bq4285E/L Enhanced RTC With NVRAM Control Features BCD or binary format for clock and calendar data General Description Direct clock/calendar replacement for IBM(R) AT-compatible computers and other applications Calendar in day of the week, day of the month, months, and years, with automatic leap-year adjustment The CMOS bq4285E/L is a low-power microprocessor peripheral providing a time-of-day clock and 100-year calendar with alarm features and battery operation. Other features include three maskable interrupt sources, square wave output, and 114 bytes of general nonvolatile storage. 114 bytes of general nonvolatile storage Enhanced features include: - System wake-up capability-- alarm interrupt output active in battery-backup mode Time of day in seconds, minutes, and hours - 12- or 24-hour format Optional daylight saving adjustment - 2.7-3.6V operation (bq4285L); 4.5-5.5V operation (bq4285E) Programmable square wave output - 32kHz output for power management Three individually maskable interrupt event flags: Automatic backup and writeprotect control to external SRAM - Periodic rates from 122s to 500ms Functionally compatible with the DS1285 - Time-of-day alarm once per second to once per day Less than 0.5 A load under battery operation - End-of-clock update cycle 24-pin plastic DIP or SOIC Selectable Intel or Motorola bus timing (PLCC), Intel bus timing (DIP and SOIC) A 32.768kHz output is available for sustaining power-management activities. Wake-up capability is provided by an alarm interrupt, which is active in battery-backup mode. The bq4285E/L write-protects the clock, calendar, and storage registers during power failure. A backup battery then maintains data and operates the clock and calendar. The bq4285E/L is a fully compatible re a l - ti me cl o ck f o r IB M ATcompatible computers and other applications. The only external components are a 32.768kHz crystal and a backup battery. T h e b q 4 2 8 5 E / L i n te g ra te s a battery-backup controller to make a 14 bytes for clock/calendar and control Pin Names Pin Connections 24-Pin DIP or SOIC MOT AD0 AD1 AD2 AD3 AD4 AD5 NC 5 6 7 8 9 10 11 25 24 23 22 21 20 19 CEIN BC INT RST DS VSS R/ W CS AS NC VCC SQW CEOUT CEIN BC INT RST DS VSS R/W AS CS 4 3 2 1 28 27 26 24 23 22 21 20 19 18 17 16 15 14 13 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 10 11 12 AD6 NC AD7 VSS VOUT X1 X2 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 VSS X2 X1 MOT VOUT VCC SQW CEOUT AD0-AD7 28-Pin PLCC PN428501.eps PN428502.eps Jan. 1999 B 1 CS AS DS R/W INT RST SQW BC X1-X2 NC CEIN CEOUT VOUT VCC Multiplexed address/data input/output Bus type select input (PLCC only ) Chip select input Address strobe input Data strobe input Read/write input Interrupt request output Reset input Square wave output 3V backup cell input Crystal inputs No connect RAM chip enable input RAM chip enable output Supply output +5V supply bq4285E/L Block Diagram standard CMOS SRAM nonvolatile during power-fail conditions. During power-fail, the bq4285E/L automatically write-protects the external SRAM and provides a V CC output sourced from the clock backup battery. The setting should not be changed during system operation. MOT is internally pulled low by a 20K resistor. For the DIP and SOIC packages, this pin is internally connected to VSS, enabling the bus timing for the Intel architecture. Pin Descriptions AD0-AD7 CS Multiplexed address/data input/ output CS should be driven low and held stable during the data-transfer phase of a bus cycle accessing the bq4285E/L. The bq4285E/L bus cycle consists of two phases: the address phase and the datatransfer phase. The address phase precedes the data-transfer phase. During the address phase, an address placed on AD0-AD7 is latched into the bq4285E/L on the falling edge of the AS signal. During the datatransfer phase of the bus cycle, the AD0-AD7 pins serve as a bidirectional data bus. MOT Chip select input Table 1. Bus Setup Bus Type Bus type select input (PLCC package only) MOT DS R/W AS Level Equivalent Equivalent Equivalent Motorola VCC MOT selects bus timing for either Motorola or Intel architecture. This pin should be tied to VCC for Motorola timing or to VSS for Intel timing (see Table 1). Intel VSS DS, E, or 2 R/W RD, MEMR, or I/OR WR, MEMW, or ALE I/OW AS Jan. 1999 B 2 bq4285E/L AS Reset may be disabled by connecting RST to VCC. This allows the control bits to retain their states through power-down/power-up cycles. Address strobe input AS serves to demultiplex the address/data bus. The falling edge of AS latches the address on AD0-AD7. This demultiplexing process is independent of the CS signal. For DIP, SOIC, and PLCC packages with MOT = VCC, the AS input is provided a signal similar to ALE in an Intel-based system. DS SQW SQW may output a programmable frequency square-wave signal during normal (VCC valid) system operation. Any one of the 13 specific frequencies may be selected through register A. This pin is held low when the square-wave enable bit (SQWE) in register B is 0 (see the Control/Status Registers section). Data strobe input For DIP, SOIC, and PLCC packages with MOT = VSS, the DS input is provided a signal similar to RD, MEMR, or I/OR in an Intel-based system. The falling edge on DS is used to enable the outputs during a read cycle. A 32.768kHz output is enabled by setting the SQWE bit in register B to 1 and the 32KE bit in register C to 1 after setting OSC2-OSC0 in register A to 011 (binary). For the PLCC package, when MOT = VCC, D S c o nt r o ls dat a t r ansf e r d u ri n g a bq4285E/L bus cycle. During a read cycle, the bq4285E/L drives the bus after the rising edge on DS. During a write cycle, the falling edge on DS is used to latch write data into the chip. R/W BC Read/write input Upon power-up, a voltage within the VBC range must be present on the BC pin for the oscillator to start up. X1-X2 For the PLCC package, when MOT = VCC, the level on R/W identifies the direction of data transfer. A high level on R/W indicates a read bus cycle, whereas a low on this pin indicates a write bus cycle. Crystal inputs The X1-X2 inputs are provided for an external 32.768Khz quartz crystal, Daiwa DT-26 or equivalent, with 6pF load capacitance. A trimming capacitor may be necessary for extremely precise time-base generation. Interrupt request output CEIN INT is an open-drain output. This allows INT to be valid in battery-backup mode for the alarm interrupt. To use this feature, INT must be connected to a power supply other than VCC. INT is asserted low when any event flag is set and the corresponding event enable bit is also set. INT becomes high-impedance whenever register C is read (see the Control/Status Registers section). RST 3V backup cell input BC should be connected to a 3V backup cell for RTC operation and storage register nonvolatility in the absence of power. When VCC slews down past VBC (3V typical), the integral control circuitry switches the power source to BC. When VCC returns above VBC, the power source is switched to VCC. For DIP, SOIC, and PLCC packages with MOT = VSS, R/W is provided a signal similar to WR, MEMW, or I/OW in an Intelbased system. The rising edge on R/W latches data into the bq4285E/L. INT Square-wave output External RAM chip enable input, active low CEIN should be driven low to enable the controlled external RAM. CEIN is internally pulled up with a 50K resistor. CEOUT External RAM chip enable output, active low When power is valid, CEOUT reflects CEIN. Reset input VOUT The bq4285E/L is reset when RST is pulled low. When reset, INT becomes highimpedance, and the bq4285E/L is not accessible. Table 4 in the Control/Status Registers section lists the register bits that are cleared by a reset. Supply output VOUT provides the higher of VCC or VBC, switched internally, to supply external RAM. Jan. 1999 B 3 VCC Positive power supply VSS Ground bq4285E/L Functional Description update period (see Figure 2). The alarm flag bit may also be set during the update cycle. Address Map The bq4285E/L copies the local register updates into the user buffer accessed by the host processor. When a 1 is written to the update transfer inhibit bit (UTI) in register B, the user copy of the clock and calendar bytes remains unchanged, while the local copy of the same bytes continues to be updated every second. The bq4285E/L provides 14 bytes of clock and control/status registers and 114 bytes of general nonvolatile storage. Figure 1 illustrates the address map for the bq4285L. The update-in-progress bit (UIP) in register A is set tBUC time before the beginning of an update cycle (see Figure 2). This bit is cleared and the update-complete flag (UF) is set at the end of the update cycle. Update Period The update period for the bq4285E/L is one second. The bq4285E/L updates the contents of the clock and calendar locations during the update cycle at the end of each Figure 1. Address Map Figure 2. Update Period Timing and UIP Jan. 1999 B 4 bq4285E/L Programming the RTC 2. Write new values to all the time, alarm, and calendar locations. The time-of-day, alarm, and calendar bytes can be written in either the BCD or binary format (see Table 2). 3. Clear the UTI bit to allow update transfers. On the next update cycle, the RTC updates all 10 bytes in the selected format. These steps may be followed to program the time, alarm, and calendar: 1. Square-Wave Output Modify the contents of register B: a. Write a 1 to the UTI bit to prevent transfers between RTC bytes and user buffer. b. Write the appropriate value to the data format (DF) bit to select BCD or binary format for all time, alarm, and calendar bytes. c. Write the appropriate value to the hour format (HF) bit. The bq4285E/L divides the 32.768kHz oscillator frequency to produce the 1 Hz update frequency for the clock and calendar. Thirteen taps from the frequency divider are fed to a 16:1 multiplexer circuit. The output of this mux is fed to the SQW output and periodic interrupt generation circuitry. The four least-significant bits of register A, RS0-RS3, select among the 13 taps (see Table 3). The square-wave output is enabled by writing a 1 to the square-wave enable bit (SQWE) in register B. A 32.768kHz output may be selected by setting OSC2-OSC0 in register A to 011 while SQWE = 1 and 32KE = 1. Table 2. Time, Alarm, and Calendar Formats Range Address RTC Bytes Decimal Binary Binary-Coded Decimal 0 Seconds 0-59 00H-3BH 00H-59H 1 Seconds alarm 0-59 00H-3BH 00H-59H 2 Minutes 0-59 00H-3BH 00H-59H 3 Minutes alarm 0-59 00H-3BH 00H-59H Hours, 12-hour format 1-12 01H-OCH AM; 81H-8CH PM 01H-12H AM; 81H-92H PM Hours, 24-hour format 0-23 00H-17H 00H-23H Hours alarm, 12-hour format 1-12 01H-OCH AM; 81H-8CH PM 01H-12H AM; 81H-92H PM Hours alarm, 24-hour format 0-23 00H-17H 00H-23H 6 Day of week (1=Sunday) 1-7 01H-07H 01H-07H 7 Day of month 1-31 01H-1FH 01H-31H 8 Month 1-12 01H-0CH 01H-12H 9 Year 0-99 00H-63H 00H-99H 4 5 Jan. 1999 B 5 bq4285E/L Interrupts Two methods can be used to process bq4285E/L interrupt events: The bq4285E/L allows three individually selected interrupt events to generate an interrupt request. These three interrupt events are: n n n n The periodic interrupt, programmable to occur once every 122 s to 500 ms. n The alarm interrupt, programmable to occur once per second to once per day, is active in battery-backup mode, providing a "wake-up" feature. Enable interrupt events and use the interrupt request output to invoke an interrupt service routine. Do not enable the interrupts and use a polling routine to periodically check the status of the flag bits. The individual interrupt sources are described in detail in the following sections. Periodic Interrupt The update-ended interrupt, which occurs at the end of each update cycle. The mux output used to drive the SQW output also drives the interrupt-generation circuitry. If the periodic interrupt event is enabled by writing a 1 to the periodic interrupt enable bit (PIE) in register C, an interrupt request is generated once every 122s to 500ms. The period between interrupts is selected by the same bits in register A that select the square wave frequency (see Table 3). Setting OSC2-OSC0 in register A to 011 does not affect the periodic interrupt timing. Each of the three interrupt events is enabled by an individual interrupt-enable bit in register B. When an event occurs, its event flag bit in register C is set. If the corresponding event enable bit is also set, then an interrupt request is generated. The interrupt request flag bit (INTF) of register C is set with every interrupt request. Reading register C clears all flag bits, including INTF, and makes INT high-impedance. Table 3. Square-Wave Frequency/Periodic Interrupt Rate Register A Bits Square Wave OSC2 OSC1 OSC0 RS3 RS2 RS1 RS0 Frequency 0 1 0 0 0 0 0 None 0 1 0 0 0 0 1 256 Hz 3.90625 ms 0 1 0 0 0 1 0 128 Hz 7.8125 ms 0 1 0 0 0 1 1 8.192 kHz 122.070 s 0 1 0 0 1 0 0 4.096 kHz 244.141 s 0 1 0 0 1 0 1 2.048 kHz 488.281 s 0 1 0 0 1 1 0 1.024 kHz 976.5625 0 1 0 0 1 1 1 512 Hz 1.95315 ms 0 1 0 1 0 0 0 256 Hz 3.90625 ms 0 1 0 1 0 0 1 128 Hz 7.8125 ms 0 1 0 1 0 1 0 64 Hz 15.625 ms 0 1 0 1 0 1 1 32 Hz 31.25 ms 0 1 0 1 1 0 0 16 Hz 62.5 0 1 0 1 1 0 1 8 Hz 125 ms 0 1 0 1 1 1 0 4 Hz 250 ms 0 1 0 1 1 1 1 2 Hz 500 ms 0 1 1 X X X X kHz same as above defined by RS3-RS0 32.768 Units Periodic Interrupt Period Units None s ms Jan. 1999 B 6 bq4285E/L Accessing RTC bytes Alarm Interrupt The alarm interrupt request is valid in battery-backup mode, providing a "wake-up" capability. During each update cycle, the RTC compares the hours, minutes, and seconds bytes with the three corresponding alarm bytes. If a match of all bytes is found, the alarm interrupt event flag bit, AF in register C, is set to 1. If the alarm event is enabled, an interrupt request is generated. Time and calendar bytes read during an update cycle may be in error. Three methods to access the time and calendar bytes without ambiguity are: n An alarm byte may be removed from the comparison by setting it to a "don't care" state. An alarm byte is set to a "don't care" state by writing a 1 to each of its two mostsignificant bits. A "don't care" state may be used to select the frequency of alarm interrupt events as follows: n n n n n n If none of the three alarm bytes is "don't care," the frequency is once per day, when hours, minutes, and seconds match. If only the hour alarm byte is "don't care," the frequency is once per hour, when minutes and seconds match. Enable the update interrupt event to generate interrupt requests at the end of the update cycle. The interrupt handler has a maximum of 999ms to access the clock bytes before the next update cycle begins (see Figure 3). Poll the update-in-progress bit (UIP) in register A. If UIP = 0, the polling routine has a minimum of tBUC time to access the clock bytes (see Figure 3). Use the periodic interrupt event to generate interrupt requests every tPI time, such that UIP = 1 always occurs between the periodic interrupts. The interrupt handler will have a minimum of tPI/2 + tBUC time to access the clock bytes (see Figure 3). Oscillator Control If only the hour and minute alarm bytes are "don't care," the frequency is once per minute, when seconds match. When power is first applied to the bq4285E/L and VCC is above VPFD, the internal oscillator and frequency divider are turned on by writing a 010 pattern to bits 4 through 6 of register A. A pattern of 011 behaves as 010 but additionally transforms register C into a read/write register. This allows the 32.768kHz output on the square wave pin to be turned on. A pattern of 11X turns the oscillator on, but keeps the frequency divider disabled. Any other pattern to these bits keeps the oscillator off. If the hour, minute, and second alarm bytes are "don't care," the frequency is once per second. Update Cycle Interrupt The update cycle ended flag bit (UF) in register C is set to a 1 at the end of an update cycle. If the update interrupt enable bit (UIE) of register B is 1, and the update transfer inhibit bit (UTI) in register B is 0, then an interrupt request is generated at the end of each update cycle. Figure 3. Update-Ended/Periodic Interrupt Relationship Jan. 1999 B 7 bq4285E/L not terminated within time tWPT (30s maximum), the chip enable output is unconditionally driven high, write-protecting the controlled SRAM. Power-Down/Power-Up Cycle The bq4285E/L power-up/power-down cycles are different. The bq4285L continuously monitors VCC for out-oftolerance. During a power failure, when VCC falls below VPFD (2.53V typical), the bq4285L write-protects the clock and storage registers. The power source is switched to BC when VCC is less than VPFD and BC is greater than VPFD, or when VCC is less than VBC and VBC is less than VPFD. RTC operation and storage data are sustained by a valid backup energy source. When VCC is above VPFD, the power source is VCC. Write-protection continues for tCSR time after VCC rises above VPFD. As the supply continues to fall past VPFD, an internal switching device forces VOUT to the external backup energy source. CEOUT is held high by the VOUT energy source. During power-up, VOUT is switched back to the main supply as VCC rises above the backup cell input voltage sourcing VOUT. If VPFD < VBC on the bq4285L, the switch to the main supply occurs at VPFD. CEOUT is held inactive for time tCER (200ms maximum) after the power supply has reached VPFD, independent of the CEIN input, to allow for processor stabilization. The bq4285E continuously monitors V CC for out-oftolerance. During a power failure, when VCC falls below VPFD (4.17V typical), the bq4285E write-protects the clock and storage registers. When VCC is below VBC (3V typical), the power source is switched to BC. RTC operation and storage data are sustained by a valid backup energy source. When VCC is above VBC, the power source is VCC. Writeprotection continues for tCSR time after VCC rises above VPFD. During power-valid operation, the CEIN input is passed through to the CEOUT output with a propagation delay of less than 10ns. Figure 4 shows the hardware hookup for the external RAM. A primary backup energy source input is provided on the bq4285E/L. The BC input accepts a 3V primary battery, typically some type of lithium chemistry. To prevent battery drain when there is no valid data to retain, VOUT and CEOUT are internally isolated from BC by the initial connection of a battery. Following the first application of VCC above VPFD, this isolation is broken, and the backup cell provides power to VOUT and CEOUT for the external SRAM. An external CMOS static RAM is battery-backed using the V O U T and chip enable output pins from the bq4285E/L. As the voltage input VCC slows down during a power failure, the chip enable output, CEOUT, is forced inactive independent of the chip enable input CEIN. This activity unconditionally write-protects the external SRAM as VCC falls below VPFD. If a memory access is in process to the external SRAM during power-fail detection, that memory cycle continues to completion before the memory is write-protected. If the memory cycle is Figure 4. External RAM Hookup to the bq4285E/L RTC Jan. 1999 B 8 bq4285E/L The four control/status registers of the bq4285E/L are accessible regardless of the status of the update cycle (see Table 4). vider. A pattern of 011 behaves as 010 but additionally transforms register C into a read/write register. This allows the 32.768kHz output on the square wave pin to be turned on. A pattern of 11X turns the oscillator on, but keeps the frequency divider disabled. When 010 is written, the RTC begins its first update after 500ms. Register A UIP - Update Cycle Status Control/Status Registers 7 UIP 6 OS2 Register A Bits 5 4 3 2 OS1 OS0 RS3 RS2 1 RS1 7 UIP 0 RS0 Register A programs: n n 5 - 4 - 3 - 2 - 1 - 0 - This read-only bit is set prior to the update cycle. When UIP equals 1, an RTC update cycle may be in progress. UIP is cleared at the end of each update cycle. This bit is also cleared when the update transfer inhibit (UTI) bit in register B is 1. The frequency of the square-wave and the periodic event rate. Oscillator operation. Register A provides: n 6 - Register B Status of the update cycle. RS0-RS3 - Frequency Select 7 - 6 - 5 - 4 - 3 RS3 2 RS2 1 RS1 7 UTI 0 RS0 6 PIE 5 AIE Register B Bits 4 3 2 UIE SQWE DF 1 HF 0 DSE Register B enables: These bits select one of the 13 frequencies for the SQW output and the periodic interrupt rate, as shown in Table 3. n Update cycle transfer operation n Square-wave output n Interrupt events n Daylight saving adjustment OS0-OS2 - Oscillator Control 7 - 6 OS2 5 OS1 4 OS0 3 - 2 - 1 - 0 - Register B selects: n These three bits control the state of the oscillator and divider stages. A pattern of 010 enables RTC operation by turning on the oscillator and enabling the frequency di- Clock and calendar data formats All bits of register B are read/write. Table 4. Control/Status Registers Reg. Bit Name and State on Reset Loc. (Hex) Read Write 6 5 4 3 2 UIP na OS2 na OS1 na OS0 na Yes Yes UTI na PIE 0 AIE 0 UIE 0 SQWE 0 Yes No2 INTF 0 PF 0 AF 0 UF 0 - 0 Yes No na - 0 - 0 - 0 - 0 0A Yes B 0B C 0C D 0D Notes: 7 (MSB) Yes1 A VRT RS3 na = not affected. 1. Except bit 7. 2. Read/write only when OSC2-OSC0 in register A is 011 (binary). Jan. 1999 B 9 1 0 (LSB) na RS2 na RS1 na DF na 32KE na - 0 HF RS0 na na DSE na - 0 - 0 - 0 - 0 bq4285E/L DSE - Daylight Saving Enable 7 - 6 - 5 - 4 - UIE - Update Cycle Interrupt Enable 3 - 2 - 1 - 0 DSE 7 - This bit enables daylight-saving time adjustments when written to 1: n n 5 - 4 - 3 - 2 - 1 HF 4 UIE 3 - 2 - 1 - 0 - 1 = Enabled 0 = Disabled The UIE bit is automatically cleared when the UTI bit equals 1. On the first Sunday in April, the time springs forward from 2:00:00 AM to 3:00:00 AM. 6 - 5 - This bit enables an interrupt request due to an update ended interrupt event: On the last Sunday in October, the first time the bq4285E/L increments past 1:59:59 AM, the time falls back to 1:00:00 AM. 7 - 6 - AIE - Alarm Interrupt Enable 0 - 7 - HF - Hour Format This bit selects the time-of-day and alarm hour format: 6 - 5 AIE 4 - 3 - 2 - 1 - 0 - This bit enables an interrupt request due to an alarm interrupt event: 1 = 24-hour format 1 = Enabled 0 = 12-hour format 0 = Disabled 7 - 6 - 5 - 4 - 3 - 2 DF 1 - 0 - PIE - Periodic Interrupt Enable 7 - DF - Data Format This bit selects the numeric format in which the time, alarm, and calendar bytes are represented: 1 = Binary 6 PIE 5 - 4 - 3 - 2 - 1 - 0 - This bit enables an interrupt request due to a periodic interrupt event: 1 = Enabled 0 = BCD 0 = Disabled 7 - 6 - 5 - 4 - 3 SQWE 2 - 1 - 0 - UTI - Update Transfer Inhibit 7 UTI SQWE - Square-Wave Enable 6 - 5 - 4 - 3 - 2 - 1 - 0 - This bit enables the square-wave output: This bit inhibits the transfer of RTC bytes to the user buffer: 1 = Enabled 0 = Disabled and held low 1 = Inhibits transfer and clears UIE 0 = Allows transfer Jan. 1999 B 10 bq4285E/L INTF - Interrupt Request Flag Register C 7 INTF 6 PF 5 AF Register C Bits 4 3 2 UF 0 32KE 1 0 7 INTF 0 0 6 - 5 - 4 - 3 - 2 - 1 - 0 - This flag is set to a 1 when any of the following is true: Register C is the read-only event status register. AIE = 1 and AF = 1 Bits 0-3 - Unused Bits 7 - 6 - PIE = 1 and PF = 1 5 - 4 - 3 0 2 - 1 0 0 0 UIE = 1 and UF = 1 Reading register C clears this bit. These bits are always set to 0. Register D 32KE-32KHz Enable Output 7 - 6 - 5 - 4 - 3 - 2 32KE 1 - 7 VRT 0 - 6 0 5 0 Register D Bits 4 3 0 0 2 0 1 0 0 0 Register D is the read-only data integrity status register. This bit may be set to a 1 only when the OSC2-OSC0 bits in register A are set to 011. Setting OSC2-OSC0 to anything other than 011 clears this bit. If SQWE in register B and 32KE are set, a 32.768KHz waveform is output on the square wave pin. Bits 0-6 - Unused Bits 7 - UF - Update-Event Flag 7 - 6 - 5 - 6 0 5 0 4 0 3 0 2 0 1 0 0 0 3 - 2 - 1 - 0 - These bits are always set to 0. 4 UF 3 - 2 - 1 - 0 - VRT - Valid RAM and Time This bit is set to a 1 at the end of the update cycle. Reading register C clears this bit. 7 VRT 6 - 5 - 4 - 1 = Valid backup energy source AF - Alarm Event Flag 0 = Backup energy source is depleted 7 - 6 - 5 AF 4 - 3 - 2 - 1 - When the backup energy source is depleted (VRT = 0), data integrity of the RTC and storage registers is not guaranteed. 0 - This bit is set to a 1 when an alarm event occurs. Reading register C clears this bit. PF - Periodic Event Flag 7 - 6 PF 5 - 4 - 3 - 2 - 1 - 0 - This bit is set to a 1 every tPI time, where tPI is the time period selected by the settings of RS0-RS3 in register A. Reading register C clears this bit. Jan. 1999 B 11 bq4285E/L Absolute Maximum Ratings--bq4285E Value Unit VCC Symbol DC voltage applied on VCC relative to VSS Parameter -0.3 to 7.0 V VT DC voltage applied on any pin excluding VCC relative to VSS -0.3 to 7.0 V TOPR Operating temperature VT VCC + 0.3 0 to +70 C Commercial -40 to +85 C Industrial "N" TSTG Storage temperature -55 to +125 C TBIAS Temperature under bias -40 to +85 C TSOLDER Soldering temperature 260 C Note: Conditions For 10 seconds Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be limited to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to conditions beyond the operational limits for extended periods of time may affect device reliability. Absolute Maximum Ratings--bq4285L Symbol Parameter Value Unit Conditions VCC DC voltage applied on VCC relative to VSS -0.3 to 6.0 V VT DC voltage applied on any pin excluding VCC relative to VSS -0.3 to 6.0 V VT VCC + 0.3 TOPR Operating temperature 0 to +70 C Commercial TSTG Storage temperature -55 to +125 C TBIAS Temperature under bias -40 to +85 C TSOLDER Soldering temperature 260 C Note: For 10 seconds Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be limited to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to conditions beyond the operational limits for extended periods of time may affect device reliability. Jan. 1999 B 12 bq4285E/L Recommended DC Operating Conditions--bq4285E (TA = TOPR) Symbol Parameter Minimum Typical Maximum Unit VCC Supply voltage 4.5 5.0 5.5 V VIL Input low voltage -0.3 - 0.8 V VIH Input high voltage 2.2 - VCC + 0.3 V VBC Backup cell voltage 2.5 - 4.0 V Notes: Typical values indicate operation at TA = 25C. Potentials are relative to VSS. Recommended DC Operating Conditions--bq4285L (TA = TOPR) Symbol Parameter Minimum Typical Maximum Unit VCC Supply voltage 2.7 3.15 3.6 V VIL Input low voltage -0.3 - 0.6 V VIH Input high voltage 2.2 - VCC + 0.3 V VBC Backup cell voltage 2.4 - 4.0 V Notes: Typical values indicate operation at TA = 25C. Potentials are relative to VSS. Crystal Specifications--bq4285E/L (DT-26 or Equivalent) Symbol Parameter Minimum Typical Maximum Unit fO Oscillation frequency - 32.768 - kHz CL Load capacitance - 6 - pF TP Temperature turnover point 20 25 30 C k Parabolic curvature constant - - -0.042 ppm/C Q Quality factor 40,000 70,000 - R1 Series resistance - - 45 K C0 Shunt capacitance - 1.1 1.8 pF C0/C1 Capacitance ratio - 430 600 DL Drive level - - 1 W f/fO Aging (first year at 25C) - 1 - ppm Jan. 1999 B 13 bq4285E/L DC Electrical Characteristics--bq4285E (TA = TOPR, VCC = 5V 10%) Symbol Parameter Minimum Typical Maximum Unit Conditions/Notes ILI Input leakage current - - 1 A VIN = VSS to VCC ILO Output leakage current - - 1 A AD0-AD7, INT, and SQW in high impedance, VOUT = VSS to VCC VOH Output high voltage 2.4 - - V IOH = -2.0 mA VOL Output low voltage - - 0.4 V IOL = 4.0 mA ICC Operating supply current - 7 15 mA VSO Supply switch-over voltage - VBC - V ICCB Battery operation current - 0.3 0.5 A VBC = 3V, TA = 25C, no load on VOUT or CEOUT ICCSB Standby supply current - 300 - A VIN = VCC or VSS, CS VCC - 0.2, no load on VOUT VPFD Power-fail-detect voltage 4.0 4.17 4.35 V VOUT1 VOUT voltage VCC - 0.3V - - V VOUT2 VOUT voltage VBC - 0.3V IMOTH Input current when MOT = VCC - - -275 A Internal 20K pull-down ICE Chip enable input current - - 100 A Internal 50K pull-up Note: Min. cycle, duty = 100%, IOH = 0mA, IOL = 0mA IOUT = 100mA, VCC >VBC IOUT = 100A, VCC < VBC Typical values indicate operation at TA = 25C, VCC = 5V or VBC = 3V. Jan. 1999 B 14 bq4285E/L DC Electrical Characteristics--bq4285L (TA = TOPR, VCC = 3.13V 0.45%) Symbol Parameter Minimum Typical Maximum Unit Conditions/Notes ILI Input leakage current - - 1 A VIN = VSS to VCC ILO Output leakage current - - 1 A AD0-AD7, INT, and SQW in high impedance, VOUT = VSS to VCC VOH Output high voltage 2.2 - - V IOH = -2.0 mA VOL Output low voltage - - 0.4 V IOL = 4.0 mA ICC Operating supply current - 5 9 mA - V VBC > VPFD Supply switch-over voltage VPFD - VSO - VBC - V VBC < VPFD Min. cycle, duty = 100%, IOH = 0mA, IOL = 0mA ICCB Battery operation current - 0.3 0.5 A VBC = 3V, TA = 25C, no load on VOUT or CEOUT ICCSB Standby supply current - 100 - A VIN = VCC or VSS, CS VCC - 0.2, no load on VOUT VPFD Power-fail-detect voltage 2.4 2.53 2.65 V VOUT1 VOUT voltage VCC - 0.3V - - V VOUT2 VOUT voltage VBC - 0.3V IMOTH Input current when MOT = VCC - - -185 A Internal 30K pull-down ICE Chip enable input current - - 120 A Internal 30K pull-up Note: IOUT = 100A, VCC < VBC Typical values indicate operation at TA = 25C, VCC = 3V. Jan. 1999 B 15 IOUT = 80mA, VCC >VBC bq4285E/L Capacitance--bq4285E/L (TA = 25C, F = 1MHz, VCC = 5.0V) Symbol Parameter Minimum Typical Maximum Unit Conditions CI/O Input/output capacitance - - 7 pF VOUT = 0V CIN Input capacitance - - 5 pF VIN = 0V Note: This parameter is sampled and not 100% tested. It does not include the X1 or X2 pin. AC Test Conditions--bq4285E Parameter Test Conditions Input pulse levels 0 to 3.0 V Input rise and fall times 5 ns Input and output timing reference levels 1.5 V (unless otherwise specified) Output load (including scope and jig) See Figures 5 and 6 +5V +5V 1.15K 960 For all outputs except INT 510 INT 50pF 130pF OL-10 OL-11 Figure 6. Output Load B--bq4285E Figure 5. Output Load A--bq4285E Jan. 1999 B 16 bq4285E/L AC Test Conditions--bq4285L Parameter Test Conditions Input pulse levels 0 to 2.3 V Input rise and fall times 5 ns Input and output timing reference levels 1.2 V (unless otherwise specified) Output load (including scope and jig) See Figures 7 and 8 Figure 7. Output Load A--bq4285L Figure 8. Output Load B--bq4285L Jan. 1999 B 17 bq4285E/L Read/Write Timing--bq4285E (TA = TOPR, VCC = 5V 10%) Symbol Parameter Minimum Typical Maximum Unit tCYC Cycle time 160 - - ns tDSL DS low or RD/WR high time 80 - - ns tDSH DS high or RD/WR low time 55 - - ns tRWH R/W hold time 0 - - ns tRWS R/W setup time 10 - - ns tCS Chip select setup time 5 - - ns tCH Chip select hold time 0 - - ns tDHR Read data hold time 0 - 25 ns tDHW Write data hold time 0 - - ns tAS Address setup time 20 - - ns tAH Address hold time 5 - - ns tDAS Delay time, DS to AS rise 10 - - ns tASW Pulse width, AS high 30 - - ns tASD Delay time, AS to DS rise (RD/WR fall) 35 - - ns tOD Output data delay time from DS rise (RD fall) - - 50 ns tDW Write data setup time 30 - - ns tBUC Delay time before update - 244 - s tPI Periodic interrupt time interval - - - - tUC Time of update cycle - 1 - s Notes See Table 3 Jan. 1999 B 18 bq4285E/L Read/Write Timing--bq4285L (TA = TOPR, VCC = 3.15V 0.45%) Symbol Parameter Minimum Typical Maximum Unit tCYC Cycle time 270 - - ns tDSL DS low or RD/WR high time 135 - - ns tDSH DS high or RD/WR low time 90 - - ns tRWH R/W hold time 0 - - ns tRWS R/W setup time 15 - - ns tCS Chip select setup time 8 - - ns tCH Chip select hold time 0 - - ns tDHR Read data hold time 0 - 40 ns tDHW Write data hold time 0 - - ns tAS Address setup time 30 - - ns tAH Address hold time 15 - - ns tDAS Delay time, DS to AS rise 15 - - ns tASW Pulse width, AS high 50 - - ns tASD Delay time, AS to DS rise (RD/WR fall) 55 - - ns tOD Output data delay time from DS rise (RD fall) - - 100 ns tDW Write data setup time 50 - - ns tBUC Delay time before update - 244 - s tPI Periodic interrupt time interval - - - - tUC Time of update cycle - 1 - s Jan. 1999 B 19 Notes See Table 3 bq4285E/L Motorola Bus Read/Write Timing--bq4285E/L (PLCC Package Only) Jan. 1999 B 20 bq4285E/L Intel Bus Read Timing--bq4285E/L Intel Bus Write Timing--bq4285E/L Jan. 1999 B 21 bq4285E/L Power-Down/Power-Up Timing--bq4285E (TA = TOPR) Symbol Parameter Minimum Typical Maximum Unit Conditions tF VCC slew from 4.5V to 0V 300 - - s tR VCC slew from 0V to 4.5V 100 - - s tCSR CS at VIH after power-up 20 - 200 ms Internal write-protection period after VCC passes VPFD on power-up. tWPT Write-protect time for external RAM 10 16 30 s Delay after VCC slows down past VPFD before SRAM is write-protected. tCER Chip enable recovery time tCSR - tCSR ms Time during which external SRAM is write-protected after VCC passes VPFD on power-up. tCED Chip enable propagation delay to external SRAM - 7 10 ns Caution: Negative undershoots below the absolute maximum rating of -0.3V in battery-backup mode may affect data integrity. Power-Down/Power-Up Timing--bq4285E Jan. 1999 B 22 bq4285E/L Power-Down/Power-Up Timing--bq4285L (TA = TOPR) Symbol Parameter Minimum Typical Maximum Unit Conditions tF VCC slew from 2.7V to 0V 300 - - s tR VCC slew from 0V to 2.7V 100 - - s tCSR CS at VIH after power-up 20 - 200 ms tWPT Write-protect time for external RAM - 0 - 10 16 30 s VBC < VPFD tCER Chip enable recovery time tCSR - tCSR ms Time during which external SRAM is write-protected after VCC passes VPFD on power-up. tCED Chip enable propagation delay to external SRAM - 9 15 ns Internal write-protection period after VCC passes VPFD on power-up. VBC > VPFD Caution: Negative undershoots below the absolute maximum rating of -0.3V in battery-backup mode may affect data integrity. Power-Down/Power-Up Timing--bq4285L Jan. 1999 B 23 bq4285E/L Interrupt Delay Timing--bq4285E/L (TA = TOPR) Symbol Parameter Minimum Typical Maximum Unit tRSW Reset pulse width 5 - - s tIRR INT release from RST - - 2 s tIRD INT release from DS (RD) - - 2 s Interrupt Delay Timing--bq4285E/L (PLCC Package Only) Interrupt Delay Timing--bq4285E/L (SOIC, DIP Packages) Jan. 1999 B 24 bq4285E/bq4285L P: 24-Pin DIP (0.600") 24-Pin P (0.600" DIP) Inches Dimension Millimeters Min. Max. Min. Max. A 0.160 0.190 4.06 4.83 A1 0.015 0.040 0.38 1.02 B 0.015 0.022 0.38 0.56 B1 0.045 0.065 1.14 1.65 C 0.008 0.013 0.20 0.33 D 1.240 1.280 31.50 32.51 E 0.600 0.625 15.24 15.88 E1 0.530 0.570 13.46 14.48 e 0.600 0.670 15.24 17.02 G 0.090 0.110 2.29 2.79 L 0.115 0.150 2.92 3.81 S 0.070 0.090 1.78 2.29 S: 24-Pin SOIC (0.300") 24-Pin S (0.300" SOIC) Inches Dimension B e D E Millimeters Min. Max. Min. Max. A 0.095 0.105 2.41 2.67 A1 0.004 0.012 0.10 0.30 B 0.013 0.020 0.33 0.51 C 0.008 0.013 0.20 0.33 D 0.600 0.615 15.24 15.62 E 0.290 0.305 7.37 7.75 e 0.045 0.055 1.14 1.40 H 0.395 0.415 10.03 10.54 L 0.020 0.040 0.51 1.02 H A C .004 A1 L Jan. 1999 B 25 bq4285E/bq4285L Q: 28-Pin Quad PLCC 28-Pin Q (Quad PLCC) Inches Dimension Millimeters Min. Max. Min. Max. A 0.165 0.180 4.19 4.57 A1 0.020 - 0.51 - B 0.012 0.021 0.30 0.53 B1 0.025 0.033 0.64 0.84 C 0.008 0.012 0.20 0.30 D 0.485 0.495 12.32 12.57 D1 0.445 0.455 11.30 11.56 D2 0.390 0.430 9.91 10.92 E 0.485 0.495 12.32 12.57 E1 0.445 0.455 11.30 11.56 E2 0.390 0.430 9.91 10.92 e 0.045 0.055 1.14 1.40 Jan. 1999 B 26 bq4285E/bq4285L Data Sheet Revision History Change No. Page No. 1 1, 25 Notes: Description Package option change Last time buy for PLCC Change 1 = Jan. 1999 B changes from May 1994. Ordering Information bq4285E/L Nature of Change Temperature: blank = Commercial (0 to +70C) N = Industrial* (-40 to +85C) Package Option: P = 24-pin plastic DIP (0.600) S = 24-pin SOIC (0.300) Q = 28-pin quad PLCC--Last time buy Device: bq4285E Real-Time Clock With NVRAM Control or bq4285L Real-Time Clock With NVRAM Control *Contact factory for availability. Jan. 1999 B 27 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated