MCP6001/1R/1U/2/4 1 MHz, Low-Power Op Amp Features Description * * * * * * * The Microchip Technology Inc. MCP6001/2/4 family of operational amplifiers (op amps) is specifically designed for general-purpose applications. This family has a 1 MHz Gain Bandwidth Product (GBWP) and 90 phase margin (typical). It also maintains 45 phase margin (typical) with a 500 pF capacitive load. This family operates from a single supply voltage as low as 1.8V, while drawing 100 A (typical) quiescent current. Additionally, the MCP6001/2/4 supports rail-to-rail input and output swing, with a common mode input voltage range of VDD + 300 mV to VSS - 300 mV. This family of op amps is designed with Microchip's advanced CMOS process. Available in SC-70-5 and SOT-23-5 packages Gain Bandwidth Product: 1 MHz (typical) Rail-to-Rail Input/Output Supply Voltage: 1.8V to 6.0V Supply Current: IQ = 100 A (typical) Phase Margin: 90 (typical) Temperature Range: - Industrial: -40C to +85C - Extended: -40C to +125C * Available in Single, Dual and Quad Packages Applications The MCP6001/2/4 family is available in the industrial and extended temperature ranges, with a power supply range of 1.8V to 6.0V. Automotive Portable Equipment Photodiode Amplifier Analog Filters Notebooks and PDAs Battery-Powered Systems Package Types VOUT 1 VOUT SOT-23-5 VOUTA 1 8 VDD VINA- 2 - + + - 5 VDD VIN+ 1 7 VOUTB VSS 2 6 VINB- VIN- 3 - 4 VOUT 5 VINB+ VOUTA 1 VINA+ 3 VSS 4 MCP6004 PDIP, SOIC, TSSOP 8 VDD EP 9 14 VOUTD VOUTA 1 V - 7 VOUTB INA 2 - + + - 13 VIND- V + 6 VINB- INA 3 5 V + VDD 4 12 VIND+ 11 VSS INB VINB+ 5 R1 VINB- 6 VREF 4 VIN- MCP6001U VINA- 2 VSS + + - MCP6002 MCP6002 2x3 DFN * MCP6001 - 5 VSS PDIP, SOIC, MSOP VSS 4 VDD R2 4 VIN- VIN+ 3 VDD 2 VIN+ 3 VINA+ 3 Typical Application 5 VDD VOUT 1 - + VSS 2 SPICE Macro Models FilterLab(R) Software MindiTM Circuit Designer & Simulator Microchip Advanced Part Selector (MAPS) Analog Demonstration and Evaluation Boards Application Notes VIN SOT-23-5 SC70-5, SOT-23-5 Design Aids * * * * * * MCP6001R MCP6001 + * * * * * * R Gain = 1 + -----1R2 Non-Inverting Amplifier (c) 2009 Microchip Technology Inc. VOUTB 7 10 VINC+ - + + - 9 VINC- 8 VOUTC * Includes Exposed Thermal Pad (EP); see Table 3-1. DS21733J-page 1 MCP6001/1R/1U/2/4 NOTES: DS21733J-page 2 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 1.0 ELECTRICAL CHARACTERISTICS VDD - VSS ........................................................................7.0V Notice: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Current at Analog Input Pins (VIN+, VIN-).....................2 mA See Section 4.1.2 "Input Voltage and Current Limits". Absolute Maximum Ratings Analog Inputs (VIN+, VIN-) ........ VSS - 1.0V to VDD + 1.0V All Other Inputs and Outputs ......... VSS - 0.3V to VDD + 0.3V Difference Input Voltage ...................................... |VDD - VSS| Output Short Circuit Current ................................ Continuous Current at Output and Supply Pins ............................30 mA Storage Temperature ................................... -65C to +150C Maximum Junction Temperature (TJ)......................... .+150C ESD Protection On All Pins (HBM; MM) .............. 4 kV; 200V DC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = +25C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VL = VDD/2, RL = 10 k to VL, and VOUT VDD/2 (refer to Figure 1-1). Parameters Sym Min Typ Max Units VOS -4.5 -- +4.5 mV VOS/TA -- 2.0 -- V/C PSRR -- 86 -- dB Conditions Input Offset Input Offset Voltage Input Offset Drift with Temperature Power Supply Rejection Ratio VCM = VSS (Note 1) TA= -40C to +125C, VCM = VSS VCM = VSS Input Bias Current and Impedance IB -- 1.0 -- pA Industrial Temperature IB -- 19 -- pA TA = +85C Extended Temperature IB -- 1100 -- pA TA = +125C Input Offset Current IOS -- 1.0 -- pA Common Mode Input Impedance ZCM -- 1013||6 -- ||pF Differential Input Impedance ZDIFF -- 1013||3 -- ||pF Common Mode Input Range VCMR VSS - 0.3 -- VDD + 0.3 V Common Mode Rejection Ratio CMRR 60 76 -- dB VCM = -0.3V to 5.3V, VDD = 5V AOL 88 112 -- dB VOUT = 0.3V to VDD - 0.3V, VCM = VSS VOL, VOH VSS + 25 -- VDD - 25 mV VDD = 5.5V, 0.5V Input Overdrive Input Bias Current: Common Mode Open-Loop Gain DC Open-Loop Gain (Large Signal) Output Maximum Output Voltage Swing Output Short Circuit Current -- 6 -- mA VDD = 1.8V -- 23 -- mA VDD = 5.5V VDD 1.8 -- 6.0 V Note 2 IQ 50 100 170 A IO = 0, VDD = 5.5V, VCM = 5V ISC Power Supply Supply Voltage Quiescent Current per Amplifier Note 1: 2: MCP6001/1R/1U/2/4 parts with date codes prior to December 2004 (week code 49) were tested to 7 mV minimum/ maximum limits. All parts with date codes November 2007 and later have been screened to ensure operation at VDD = 6.0V. However, the other minimum and maximum specifications are measured at 1.8V and 5.5V. (c) 2009 Microchip Technology Inc. DS21733J-page 3 MCP6001/1R/1U/2/4 AC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = +25C, VDD = +1.8 to 5.5V, VSS = GND, VCM = VDD/2, VL = VDD/2, VOUT VDD/2, RL = 10 k to VL, and CL = 60 pF (refer to Figure 1-1). Parameters Sym Min Typ Max Units Conditions GBWP -- 1.0 -- MHz Phase Margin PM -- 90 -- Slew Rate SR -- 0.6 -- V/s Input Noise Voltage Eni -- 6.1 -- Vp-p Input Noise Voltage Density eni -- 28 -- nV/Hz f = 1 kHz Input Noise Current Density ini -- 0.6 -- fA/Hz f = 1 kHz AC Response Gain Bandwidth Product G = +1 V/V Noise f = 0.1 Hz to 10 Hz TEMPERATURE SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, VDD = +1.8V to +5.5V and VSS = GND. Parameters Sym Min Typ Max Units Industrial Temperature Range TA -40 -- +85 C Extended Temperature Range TA -40 -- +125 C Operating Temperature Range TA -40 -- +125 C Storage Temperature Range TA -65 -- +150 C Thermal Resistance, 5L-SC70 JA -- 331 -- C/W Thermal Resistance, 5L-SOT-23 JA -- 256 -- C/W Thermal Resistance, 8L-PDIP JA -- 85 -- C/W Thermal Resistance, 8L-SOIC (150 mil) JA -- 163 -- C/W Thermal Resistance, 8L-MSOP JA -- 206 -- C/W Thermal Resistance, 8L-DFN (2x3) JA -- 68 -- C/W Thermal Resistance, 14L-PDIP JA -- 70 -- C/W Thermal Resistance, 14L-SOIC JA -- 120 -- C/W Thermal Resistance, 14L-TSSOP JA -- 100 -- C/W Conditions Temperature Ranges Note Thermal Package Resistances Note: The industrial temperature devices operate over this extended temperature range, but with reduced performance. In any case, the internal Junction Temperature (TJ) must not exceed the Absolute Maximum specification of +150C. DS21733J-page 4 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 1.1 Test Circuits The circuit used for most DC and AC tests is shown in Figure 1-1. This circuit can independently set VCM and VOUT; see Equation 1-1. Note that VCM is not the circuit's common mode voltage ((VP + VM)/2), and that VOST includes VOS plus the effects (on the input offset error, VOST) of temperature, CMRR, PSRR and AOL. CF 6.8 pF RG 100 k RF 100 k VP VDD VIN+ EQUATION 1-1: G DM = R F R G CB1 100 nF MCP600X V CM = ( V P + V DD 2 ) 2 V OUT = ( V DD 2 ) + ( V P - V M ) + V OST ( 1 + G DM ) VM RG 100 k Where: GDM = Differential Mode Gain (V/V) VCM = Op Amp's Common Mode Input Voltage (V) (c) 2009 Microchip Technology Inc. CB2 1 F VIN- V OST = V IN- - V IN+ VOST = Op Amp's Total Input Offset Voltage VDD/2 (mV) RL 10 k RF 100 k CF 6.8 pF VOUT CL 60 pF VL FIGURE 1-1: AC and DC Test Circuit for Most Specifications. DS21733J-page 5 MCP6001/1R/1U/2/4 NOTES: DS21733J-page 6 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Input Offset Voltage (V) -300 -400 TA = -40C TA = +25C TA = +85C TA = +125C -500 -600 0 0.05 0.04 0.03 0.02 0.01 0.00 -0.01 -0.02 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 -300 -400 TA = -40C TA = +25C TA = +85C TA = +125C -500 -600 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 Common Mode Input Voltage (V) Input Offset Quadratic Temp. Co.; TC2 (V/C2) Input Offset Quadratic (c) 2009 Microchip Technology Inc. -200 -700 10 12 2453 Samples TA = -40C to +125C VCM = VSS FIGURE 2-3: Temp. Co. VDD = 5.5V -100 -0.5 8 Input Offset Voltage Drift. 45% 40% 35% 30% 25% 20% 15% 10% 5% 0% 0.4 FIGURE 2-4: Input Offset Voltage vs. Common Mode Input Voltage at VDD = 1.8V. 2453 Samples TA = -40C to +125C VCM = VSS FIGURE 2-2: 0.2 Common Mode Input Voltage (V) Input Offset Voltage. -12 -10 -8 -6 -4 -2 0 2 4 6 Input Offset Voltage Drift; TC1 (V/C) 0.0 5 -0.2 4 -0.4 -2 -1 0 1 2 3 Input Offset Voltage (mV) Input Offset Voltage (V) Percentage of Occurrences -200 0.0 -3 FIGURE 2-5: Input Offset Voltage vs. Common Mode Input Voltage at VDD = 5.5V. 200 Input Offset Voltage (V) -4 FIGURE 2-1: Percentage of Occurrences VDD = 1.8V -100 -700 5 18% 16% 14% 12% 10% 8% 6% 4% 2% 0% 0 64,695 Samples VCM = VSS 0.07 20% 18% 16% 14% 12% 10% 8% 6% 4% 2% 0% 0.06 Percentage of Occurrences Note: Unless otherwise indicated, TA = +25C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT VDD/2, VL = VDD/2, RL = 10 k to VL, and CL = 60 pF. 150 100 50 0 VDD = 5.5V VDD = 1.8V -50 -100 -150 VCM = VSS -200 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Output Voltage (V) FIGURE 2-6: Output Voltage. Input Offset Voltage vs. DS21733J-page 7 MCP6001/1R/1U/2/4 Note: Unless otherwise indicated, TA = +25C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT VDD/2, VL = VDD/2, RL = 10 k to VL, and CL = 60 pF. 8% 6% 4% 2% 70 PSRR- 60 PSRR+ 50 CMRR 40 6 55% 50% 45% 40% 35% 30% 25% 20% 15% 10% 5% 0% 9 12 15 18 21 24 Input Bias Current (pA) 27 Input Bias Current at +85C. Input Bias Current (pA) Input Bias Current at PSRR (VCM = VSS) 80 CMRR (VCM = -0.3V to +5.3V) 70 -25 FIGURE 2-9: Temperature. DS21733J-page 8 PSRR, CMRR vs. 0 100 -30 80 Phase 60 Gain 20 0 -60 -90 40 -120 -150 VCM = VSS -20 0.1 1.E+ 1 1.E+ 10 1.E01 00 01 Input Noise Voltage Density (nV/Hz) 90 -50 100k 1.E+05 -180 -210 100 1.E+ 1k 1.E+ 10k 100k 1M 10M 1.E+ 1.E+ 1.E+ 1.E+ Frequency (Hz) 05 06 07 02 03 04 Open-Loop Gain, Phase vs. 1,000 95 75 1k 10k 1.E+03 1.E+04 Frequency (Hz) 120 FIGURE 2-11: Frequency. VDD = 5.0V 85 100 1.E+02 FIGURE 2-10: Frequency. Open-Loop Gain (dB) 1500 1350 1200 1050 900 750 600 300 150 0 605 Samples VDD = 5.5V VCM = VDD TA = +125C FIGURE 2-8: +125C. 20 10 1.E+01 30 Open-Loop Phase () 3 FIGURE 2-7: PSRR, CMRR (dB) 80 30 0% 100 VCM = VSS 90 PSRR, CMRR (dB) 10% 0 Percentage of Occurrences 100 1230 Samples VDD = 5.5V VCM = VDD TA = +85C 12% 450 Percentage of Occurrences 14% 0 25 50 75 Ambient Temperature (C) 100 125 CMRR, PSRR vs. Ambient 100 10 0.1 1 10 100 1.E+0 1k 10k 1.E+0 100k 1.E-01 1.E+0 1.E+0 1.E+0 1.E+0 0 1Frequency 2 (Hz)3 4 5 FIGURE 2-12: vs. Frequency. Input Noise Voltage Density (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 Note: Unless otherwise indicated, TA = +25C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT VDD/2, VL = VDD/2, RL = 10 k to VL, and CL = 60 pF. 30 0.08 Output Voltage (20 mV/div) Short Circuit Current Magnitude (mA) G = +1 V/V 25 TA = -40C TA = +25C TA = +85C TA = +125C 20 15 10 5 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Power Supply Voltage (V) FIGURE 2-13: Output Short Circuit Current vs. Power Supply Voltage. 0.02 0.00 -0.02 -0.04 -0.06 1.E-06 2.E-06 3.E-06 4.E-06 5.E-06 6.E-06 7.E-06 8.E-06 FIGURE 2-16: Pulse Response. G = +1 V/V VDD = 5.0V VOL - VSS 10 1 10 1.E-05 160 10m 1.E-02 120 100 80 40 20 3.5 3.0 2.5 2.0 1.5 1.0 0.0 TA = +125C TA = +85C TA = +25C TA = -40C 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0.E+00 1.E-05 (c) 2009 Microchip Technology Inc. 3.E-05 FIGURE 2-17: Pulse Response. 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 4.E-05 5.E-05 6.E-05 7.E-05 8.E-05 9.E-05 1.E-04 Large-Signal, Non-Inverting VDD = 5.5V Falling Edge VDD = 1.8V Rising Edge -50 -25 0 25 50 75 100 125 Ambient Temperature (C) Power Supply Voltage (V) FIGURE 2-15: Quiescent Current vs. Power Supply Voltage. 2.E-05 Time (10 s/div) VCM = VDD - 0.5V 140 60 4.0 0.5 100 1m 1.E-04 1.E-03 Output Current Magnitude (A) FIGURE 2-14: Output Voltage Headroom vs. Output Current Magnitude. 180 Output Voltage (V) 4.5 VDD - VOH 1.E-05 Small-Signal, Non-Inverting 5.0 100 9.E-06 Time (1 s/div) Slew Rate (V/s) Output Voltage Headroom (mV) 0.04 -0.08 0.E+00 1,000 Quiescent Current per amplifier (A) 0.06 FIGURE 2-18: Temperature. Slew Rate vs. Ambient DS21733J-page 9 MCP6001/1R/1U/2/4 6 10 Input, Output Voltages (V) Output Voltage Swing (V P-P ) Note: Unless otherwise indicated, TA = +25C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT VDD/2, VL = VDD/2, RL = 10 k to VL, and CL = 60 pF. VDD = 5.5V VDD = 1.8V 1 0.1 1k 1.E+03 FIGURE 2-19: Frequency. Input Current Magnitude (A) 1.E-02 10m 1m 1.E-03 100 1.E-04 10 1.E-05 1 1.E-06 100n 1.E-07 10n 1.E-08 1n 1.E-09 100p 1.E-10 10p 1.E-11 1p 1.E-12 10k 100k 1.E+04 1.E+05 Frequency (Hz) 1M 1.E+06 Output Voltage Swing vs. VIN 5 VDD = 5.0V G = +2 V/V VOUT 4 3 2 1 0 -1 0.E+00 1.E-05 2.E-05 3.E-05 4.E-05 5.E-05 6.E-05 7.E-05 8.E-05 9.E-05 1.E-04 Time (10 s/div) FIGURE 2-21: Phase Reversal. The MCP6001/2/4 Show No +125C +85C +25C -40C -1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 Input Voltage (V) FIGURE 2-20: Measured Input Current vs. Input Voltage (below VSS). DS21733J-page 10 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 3.0 PIN DESCRIPTIONS Descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE MCP6001 MCP6001R MCP6001U SC70-5, SOT-23-5 3.1 SOT-23-5 SOT-23-5 MCP6002 MSOP, PDIP, SOIC DFN 2x3 PDIP, SOIC, TSSOP Symbol Description 1 1 4 1 1 1 VOUT, VOUTA Analog Output (op amp A) 4 4 3 2 2 2 VIN-, VINA- Inverting Input (op amp A) 3 3 1 3 3 3 VIN+, VINA+ Non-inverting Input (op amp A) 5 2 5 8 8 4 VDD -- -- -- 5 5 5 VINB+ -- -- -- 6 6 6 VINB- Inverting Input (op amp B) -- -- -- 7 7 7 VOUTB Analog Output (op amp B) -- -- -- -- -- 8 VOUTC Analog Output (op amp C) -- -- -- -- -- 9 VINC- Inverting Input (op amp C) -- -- -- -- -- 10 VINC+ Non-inverting Input (op amp C) Positive Power Supply Non-inverting Input (op amp B) 2 5 2 4 4 11 VSS -- -- -- -- -- 12 VIND+ Non-inverting Input (op amp D) -- -- -- -- -- 13 VIND- Inverting Input (op amp D) -- -- -- -- -- 14 VOUTD -- -- -- -- 9 -- EP Analog Outputs The output pins are low-impedance voltage sources. 3.2 MCP6004 Analog Inputs 3.4 Negative Power Supply Analog Output (op amp D) Exposed Thermal Pad (EP); must be connected to VSS. Exposed Thermal Pad (EP) There is an internal electrical connection between the Exposed Thermal Pad (EP) and the VSS pin; they must be connected to the same potential on the Printed Circuit Board (PCB). The non-inverting and inverting inputs are high-impedance CMOS inputs with low bias currents. 3.3 Power Supply Pins The positive power supply (VDD) is 1.8V to 6.0V higher than the negative power supply (VSS). For normal operation, the other pins are at voltages between VSS and VDD. Typically, these parts are used in a single (positive) supply configuration. In this case, VSS is connected to ground and VDD is connected to the supply. VDD will need bypass capacitors. (c) 2009 Microchip Technology Inc. DS21733J-page 11 MCP6001/1R/1U/2/4 NOTES: DS21733J-page 12 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 4.0 APPLICATION INFORMATION The MCP6001/2/4 family of op amps is manufactured using Microchip's state-of-the-art CMOS process and is specifically designed for low-cost, low-power and general-purpose applications. The low supply voltage, low quiescent current and wide bandwidth makes the MCP6001/2/4 ideal for battery-powered applications. This device has high phase margin, which makes it stable for larger capacitive load applications. VDD, and dump any currents onto VDD. When implemented as shown, resistors R1 and R2 also limit the current through D1 and D2. VDD D1 R1 4.1 Rail-to-Rail Inputs 4.1.1 R2 PHASE REVERSAL INPUT VOLTAGE AND CURRENT LIMITS The ESD protection on the inputs can be depicted as shown in Figure 4-1. This structure was chosen to protect the input transistors, and to minimize input bias current (IB). The input ESD diodes clamp the inputs when they try to go more than one diode drop below VSS. They also clamp any voltages that go too far above VDD; their breakdown voltage is high enough to allow normal operation, and low enough to bypass quick ESD events within the specified limits. VDD Bond Pad R3 VSS - (minimum expected V1) 2 mA VSS - (minimum expected V2) R2 > 2 mA R1 > FIGURE 4-2: Inputs. Input Stage Bond V - IN Pad VSS Bond Pad FIGURE 4-1: Structures. Simplified Analog Input ESD In order to prevent damage and/or improper operation of these op amps, the circuit they are in must limit the currents and voltages at the VIN+ and VIN- pins (see Absolute Maximum Ratings at the beginning of Section 1.0 "Electrical Characteristics"). Figure 4-2 shows the recommended approach to protecting these inputs. The internal ESD diodes prevent the input pins (VIN+ and VIN-) from going too far below ground, and the resistors R1 and R2 limit the possible current drawn out of the input pins. Diodes D1 and D2 prevent the input pins (VIN+ and VIN-) from going too far above (c) 2009 Microchip Technology Inc. Protecting the Analog It is also possible to connect the diodes to the left of resistors R1 and R2. In this case, current through the diodes D1 and D2 needs to be limited by some other mechanism. The resistors then serve as in-rush current limiters; the DC current into the input pins (VIN+ and VIN-) should be very small. A significant amount of current can flow out of the inputs when the common mode voltage (VCM) is below ground (VSS); see Figure 2-20. Applications that are high impedance may need to limit the usable voltage range. 4.1.3 VIN+ Bond Pad MCP600X V2 The MCP6001/1R/1U/2/4 op amp is designed to prevent phase reversal when the input pins exceed the supply voltages. Figure 2-21 shows the input voltage exceeding the supply voltage without any phase reversal. 4.1.2 D2 V1 NORMAL OPERATION The input stage of the MCP6001/1R/1U/2/4 op amps use two differential CMOS input stages in parallel. One operates at low common mode input voltage (VCM), while the other operates at high VCM. WIth this topology, the device operates with VCM up to 0.3V above VDD and 0.3V below VSS. The transition between the two input stages occurs when VCM = VDD - 1.1V. For the best distortion and gain linearity, with non-inverting gains, avoid this region of operation. 4.2 Rail-to-Rail Output The output voltage range of the MCP6001/2/4 op amps is VDD - 25 mV (minimum) and VSS + 25 mV (maximum) when RL = 10 k is connected to VDD/2 and VDD = 5.5V. Refer to Figure 2-14 for more information. DS21733J-page 13 MCP6001/1R/1U/2/4 4.3 Capacitive Loads 4.4 Driving large capacitive loads can cause stability problems for voltage feedback op amps. As the load capacitance increases, the feedback loop's phase margin decreases and the closed-loop bandwidth is reduced. This produces gain peaking in the frequency response, with overshoot and ringing in the step response. While a unity-gain buffer (G = +1) is the most sensitive to capacitive loads, all gains show the same general behavior. When driving large capacitive loads with these op amps (e.g., > 100 pF when G = +1), a small series resistor at the output (RISO in Figure 4-3) improves the feedback loop's phase margin (stability) by making the output load resistive at higher frequencies. The bandwidth will be generally lower than the bandwidth with no capacitance load. - MCP600X + VIN Supply Bypass With this family of operational amplifiers, the power supply pin (VDD for single-supply) should have a local bypass capacitor (i.e., 0.01 F to 0.1 F) within 2 mm for good high-frequency performance. It also needs a bulk capacitor (i.e., 1 F or larger) within 100 mm to provide large, slow currents. This bulk capacitor can be shared with nearby analog parts. 4.5 Unused Op Amps An unused op amp in a quad package (MCP6004) should be configured as shown in Figure 4-5. These circuits prevent the output from toggling and causing crosstalk. Circuits A sets the op amp at its minimum noise gain. The resistor divider produces any desired reference voltage within the output voltage range of the op amp; the op amp buffers that reference voltage. Circuit B uses the minimum number of components and operates as a comparator, but it may draw more current. RISO VOUT CL 1/4 MCP6004 (A) VDD R1 FIGURE 4-3: Output resistor, RISO stabilizes large capacitive loads. VDD VDD VREF R2 Figure 4-4 gives recommended RISO values for different capacitive loads and gains. The x-axis is the normalized load capacitance (CL/GN), where GN is the circuit's noise gain. For non-inverting gains, GN and the Signal Gain are equal. For inverting gains, GN is 1+|Signal Gain| (e.g., -1 V/V gives GN = +2 V/V). R2 V REF = V DD * -----------------R1 + R2 FIGURE 4-5: Recommended RISO () 1000 100 VDD = 5.0V RL = 100 k GN = 1 GN 2 10 10p 1.E-11 100p 1n 10n 1.E-10 1.E-09 1.E-08 Normalized Load Capacitance; CL/GN (F) FIGURE 4-4: Recommended RISO values for Capacitive Loads. After selecting RISO for your circuit, double-check the resulting frequency response peaking and step response overshoot. Modify RISO's value until the response is reasonable. Bench evaluation and simulations with the MCP6001/1R/1U/2/4 SPICE macro model are very helpful. DS21733J-page 14 1/4 MCP6004 (B) 4.6 Unused Op Amps. PCB Surface Leakage In applications where low input bias current is critical, Printed Circuit Board (PCB) surface leakage effects need to be considered. Surface leakage is caused by humidity, dust or other contamination on the board. Under low humidity conditions, a typical resistance between nearby traces is 1012. A 5V difference would cause 5 pA of current to flow; which is greater than the MCP6001/1R/1U/2/4 family's bias current at 25C (typically 1 pA). The easiest way to reduce surface leakage is to use a guard ring around sensitive pins (or traces). The guard ring is biased at the same voltage as the sensitive pin. An example of this type of layout is shown in Figure 4-6. (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 VIN- VIN+ VSS - 1/2 MCP6002 VIN1 R1 R2 + - MCP6001 VOUT + Guard Ring FIGURE 4-6: for Inverting Gain. 1. 2. 4.7.1 VIN2 R2 + Example Guard Ring Layout Non-inverting Gain and Unity-Gain Buffer: a. Connect the non-inverting pin (VIN+) to the input with a wire that does not touch the PCB surface. b. Connect the guard ring to the inverting input pin (VIN-). This biases the guard ring to the common mode input voltage. Inverting Gain and Transimpedance Gain Amplifiers (convert current to voltage, such as photo detectors): a. Connect the guard ring to the non-inverting input pin (VIN+). This biases the guard ring to the same reference voltage as the op amp (e.g., VDD/2 or ground). b. Connect the inverting pin (VIN-) to the input with a wire that does not touch the PCB surface. 4.7 - 1/2 MCP6002 Application Circuits UNITY-GAIN BUFFER The rail-to-rail input and output capability of the MCP6001/2/4 op amp is ideal for unity-gain buffer applications. The low quiescent current and wide bandwidth makes the device suitable for a buffer configuration in an instrumentation amplifier circuit, as shown in Figure 4-7. R1 = 20 k R1 R2 = 10 k VREF R1 V OUT = ( V IN2 - V IN1 ) * ------ + V REF R2 FIGURE 4-7: Instrumentation Amplifier with Unity-Gain Buffer Inputs. 4.7.2 ACTIVE LOW-PASS FILTER The MCP6001/2/4 op amp's low input bias current makes it possible for the designer to use larger resistors and smaller capacitors for active low-pass filter applications. However, as the resistance increases, the noise generated also increases. Parasitic capacitances and the large value resistors could also modify the frequency response. These trade-offs need to be considered when selecting circuit elements. Usually, the op amp bandwidth is 100x the filter cutoff frequency (or higher) for good performance. It is possible to have the op amp bandwidth 10X higher than the cutoff frequency, thus having a design that is more sensitive to component tolerances. Figure 4-8 shows a second-order Butterworth filter with 100 kHz cutoff frequency and a gain of +1 V/V; the op amp bandwidth is only 10x higher than the cutoff frequency. The component values were selected using Microchip's FilterLab(R) software. 100 pF VIN 14.3 k 53.6 k + MCP6002 33 pF FIGURE 4-8: Low-Pass Filter. (c) 2009 Microchip Technology Inc. - VOUT Active Second-Order DS21733J-page 15 MCP6001/1R/1U/2/4 4.7.3 EQUATION 4-1: PEAK DETECTOR dV C1 I SC = C 1 ------------dt I SC dV C1 ------------- = -------dt C1 The MCP6001/2/4 op amp has a high input impedance, rail-to-rail input/output and low input bias current, which makes this device suitable for peak detector applications. Figure 4-9 shows a peak detector circuit with clear and sample switches. The peak-detection cycle uses a clock (CLK), as shown in Figure 4-9. 25mA= -------------0.1F At the rising edge of CLK, Sample Switch closes to begin sampling. The peak voltage stored on C1 is sampled to C2 for a sample time defined by tSAMP. At the end of the sample time (falling edge of Sample Signal), Clear Signal goes high and closes the Clear Switch. When the Clear Switch closes, C1 discharges through R1 for a time defined by tCLEAR. At the end of the clear time (falling edge of Clear Signal), op amp A begins to store the peak value of VIN on C1 for a time defined by tDETECT. dV C1 ------------- = 250mV s dt This voltage rate of change is less than the MCP6001/2/4 slew rate of 0.6 V/s. When the input voltage swings below the voltage across C1, D1 becomes reversebiased. This opens the feedback loop and rails the amplifier. When the input voltage increases, the amplifier recovers at its slew rate. Based on the rate of voltage change shown in the above equation, it takes an extended period of time to charge a 0.1 F capacitor. The capacitors need to be selected so that the circuit is not limited by the amplifier slew rate. Therefore, the capacitors should be less than 40 F and a stabilizing resistor (RISO) needs to be properly selected. (Refer to Section 4.3 "Capacitive Loads"). In order to define tSAMP and tCLEAR, it is necessary to determine the capacitor charging and discharging period. The capacitor charging time is limited by the amplifier source current, while the discharging time () is defined using R1 ( = R1C1). tDETECT is the time that the input signal is sampled on C1 and is dependent on the input voltage change frequency. The op amp output current limit, and the size of the storage capacitors (both C1 and C2), could create slewing limitations as the input voltage (VIN) increases. Current through a capacitor is dependent on the size of the capacitor and the rate of voltage change. From this relationship, the rate of voltage change or the slew rate can be determined. For example, with an op amp short circuit current of ISC = 25 mA and a load capacitor of C1 = 0.1 F, then: VIN + 1/2 MCP6002 - D1 Op Amp A RISO VC1 C1 R1 + 1/2 MCP6002 - RISO VC2 C2 Op Amp B + MCP6001 - VOUT Op Amp C Sample Switch Clear Switch tSAMP Sample Signal tCLEAR Clear Signal tDETECT CLK FIGURE 4-9: DS21733J-page 16 Peak Detector with Clear and Sample CMOS Analog Switches. (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 5.0 DESIGN AIDS Microchip provides the basic design tools needed for the MCP6001/1R/1U/2/4 family of op amps. 5.1 SPICE Macro Model The latest SPICE macro model for the MCP6001/1R/ 1U/2/4 op amps is available on the Microchip web site at www.microchip.com. The model was written and tested in official Orcad (Cadence) owned PSPICE. For the other simulators, it may require translation. The model covers a wide aspect of the op amp's electrical specifications. Not only does the model cover voltage, current, and resistance of the op amp, but it also covers the temperature and noise effects on the behavior of the op amp. The model has not been verified outside of the specification range listed in the op amp data sheet. The model behaviors under these conditions can not be guaranteed that it will match the actual op amp performance. Moreover, the model is intended to be an initial design tool. Bench testing is a very important part of any design and cannot be replaced with simulations. Also, simulation results using this macro model need to be validated by comparing them to the data sheet specifications and characteristic curves. 5.2 FilterLab(R) Software Microchip's FilterLab(R) software is an innovative software tool that simplifies analog active filter (using op amps) design. Available at no cost from the Microchip web site at www.microchip.com/filterlab, the FilterLab design tool provides full schematic diagrams of the filter circuit with component values. It also outputs the filter circuit in SPICE format, which can be used with the macro model to simulate actual filter performance. 5.3 5.4 Microchip Advanced Part Selector (MAPS) MAPS is a software tool that helps semiconductor professionals efficiently identify Microchip devices that fit a particular design requirement. Available at no cost from the Microchip web site at www.microchip.com/ maps, the MAPS is an overall selection tool for Microchip's product portfolio that includes Analog, Memory, MCUs and DSCs. Using this tool you can define a filter to sort features for a parametric search of devices and export side-by-side technical comparison reports. Helpful links are also provided for Data sheets, Purchase, and Sampling of Microchip parts. 5.5 Analog Demonstration and Evaluation Boards Microchip offers a broad spectrum of Analog Demonstration and Evaluation Boards that are designed to help you achieve faster time to market. For a complete listing of these boards and their corresponding user's guides and technical information, visit the Microchip web site at www.microchip.com/ analogtools. Some boards that are especially useful are: * * * * * * * MCP6XXX Amplifier Evaluation Board 1 MCP6XXX Amplifier Evaluation Board 2 MCP6XXX Amplifier Evaluation Board 3 MCP6XXX Amplifier Evaluation Board 4 Active Filter Demo Board Kit 5/6-Pin SOT-23 Evaluation Board, P/N VSUPEV2 8-Pin SOIC/MSOP/TSSOP/DIP Evaluation Board, P/N SOIC8EV * 14-Pin SOIC/TSSOP/DIP Evaluation Board, P/N SOIC14EV MindiTM Circuit Designer & Simulator Microchip's MindiTM Circuit Designer & Simulator aids in the design of various circuits useful for active filter, amplifier and power-management applications. It is a free online circuit designer & simulator available from the Microchip web site at www.microchip.com/mindi. This interactive circuit designer & simulator enables designers to quickly generate circuit diagrams, simulate circuits. Circuits developed using the Mindi Circuit Designer & Simulator can be downloaded to a personal computer or workstation. (c) 2009 Microchip Technology Inc. DS21733J-page 17 MCP6001/1R/1U/2/4 5.6 Application Notes The following Microchip Analog Design Note and Application Notes are available on the Microchip web site at www.microchip. com/appnotes and are recommended as supplemental reference resources. * ADN003: "Select the Right Operational Amplifier for your Filtering Circuits", DS21821 * AN722: "Operational Amplifier Topologies and DC Specifications", DS00722 * AN723: "Operational Amplifier AC Specifications and Applications", DS00723 * AN884: "Driving Capacitive Loads With Op Amps", DS00884 * AN990: "Analog Sensor Conditioning Circuits - An Overview", DS00990 * AN1177: "Op Amp Precision Design: DC Errors", DS01177 * AN1228: "Op Amp Precision Design: Random Noise", DS01228 * AN1297: "Microchip 's Op Amp SPICE Macro Models" These application notes and others are listed in the design guide: * "Signal Chain Design Guide", DS21825 DS21733J-page 18 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 6.0 PACKAGING INFORMATION 6.1 Package Marking Information 5-Lead SC-70 (MCP6001) XXN (Front) YWW (Back) Example: (I-Temp) Device MCP6001 I-Temp Code E-Temp Code AAN CDN AA7 (Front) 432 (Back) Note: Applies to 5-Lead SC-70. OR OR XXNN Device I-Temp Code E-Temp Code MCP6001 AANN CDNN AA74 Note: Applies to 5-Lead SC-70. Example: (E-Temp) 5-Lead SOT-23 (MCP6001/1R/1U) 5 4 XXNN 1 2 I-Temp Code E-Temp Code MCP6001 AANN CDNN MCP6001R ADNN CENN MCP6001U AFNN CFNN Device 3 5 4 CD25 1 2 3 Note: Applies to 5-Lead SOT-23. 8-Lead PDIP (300 mil) MCP6002 I/P256 0432 XXXXXXXX XXXXXNNN YYWW 8-Lead DFN (2 x 3) XXX YWW NN OR MCP6002 e3 I/P^^256 0746 Example: ABY 944 25 Legend: XX...X Y YY WW NNN e3 * Note: Example: Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2009 Microchip Technology Inc. DS21733J-page 19 MCP6001/1R/1U/2/4 Package Marking Information (Continued) 8-Lead SOIC (150 mil) Example: MCP6002I SN0432 256 XXXXXXXX XXXXYYWW NNN MCP6002I e3 SN^^0746 256 OR Example: 8-Lead MSOP XXXXXX 6002I YWWNNN 432256 14-Lead PDIP (300 mil) (MCP6004) Example: XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN MCP6004 e3 I/P^^ 0432256 OR MCP6004 e3 E/P^^ 0746256 14-Lead SOIC (150 mil) (MCP6004) XXXXXXXXXX XXXXXXXXXX YYWWNNN 14-Lead TSSOP (MCP6004) Example: OR 0432256 Example: XXXXXX YYWW 6004ST 0432 NNN 256 DS21733J-page 20 MCP6004 e3 E/SL^^ 0746256 MCP6004ISL OR 6004STE 0432 256 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / D b 3 1 2 E1 E 4 5 e A e A2 c A1 L 3# 4# 5$8 %1 44" " 5 5 56 7 ( 1# 6, : # ; < ; < < !!1/ / #! %% 9()* 6, =!# " ; !!1/=!# " ( ( ( 6, 4# ; ( . 4 9 #4# 4! / 4!=!# ; < 9 8 ( < !"! #$! !% # $ !% # $ !# "'( )*+ ) #&#,$ --# $## #&! ! (c) 2009 Microchip Technology Inc. - *9) DS21733J-page 21 MCP6001/1R/1U/2/4 . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / DS21733J-page 22 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 ! . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / b N E E1 3 2 1 e e1 D A2 A c A1 L L1 3# 4# 5$8 %1 44" " 5 56 7 5 ( 4!1# ()* 6$# !4!1# 6, : # < ; < < ( 6, =!# " < !!1/=!# " < ; 6, 4# < !!1/ / #! %% )* ( . #4# 4 < 9 . # # 4 ( < ; . # I > < > ; < 9 4! / 4!=!# 8 < ( !"! #$! !% # $ !% # $ #&! ! !# "'( )*+ ) #&#,$ --# $## (c) 2009 Microchip Technology Inc. - *) DS21733J-page 23 MCP6001/1R/1U/2/4 " # $ % &'() *!*+,-.#$ . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / e D b N N L K E2 E EXPOSED PAD NOTE 1 NOTE 1 2 1 1 2 D2 BOTTOM VIEW TOP VIEW A A3 A1 NOTE 2 3# 4# 5$8 %1 44" " 5 5 56 7 ; 1# 6, : # ; #! %% ( * ## / ()* ". 6, 4# )* 6, =!# " "& !1!4# < "& !1!=!# " ( < ( 8 ( 4 ( ? < < * ##=!# * ##4# * ### "& !1! )* (( 1, $!&%#$ , 08$#$ #8 #!-# # # ! 1/ , & !#8 #! 1/ - $#! !# "'( )*+ ) #&#,$ --# $## ".+ % 0$ $-# $## 0% % # $ DS21733J-page 24 - ** (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 " # $ % &'() *!*+,-.#$ . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / (c) 2009 Microchip Technology Inc. DS21733J-page 25 MCP6001/1R/1U/2/4 " # / )! -. #/ . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / N NOTE 1 E1 1 3 2 D E A2 A L A1 c e eB b1 b 3# 4# 5$8 %1 5*:" 5 5 1# 7 ; # #1 56 )* < < ( ( ) # #1 ( < < " ( !!1/ $! # / $! =!# !!1/=!# " ( ; 6, 4# ; 9( ( # #1 4 ( / ; ( 4!=!# 8 9 8 ; ) < < 4! 3 4 - 4!=!# 6, - @ 1, $!&%#$ , 08$#$ #8 #!-# # # ! @%#* # # !"! #$! !% # $ !% # $ !# "'( )*+) #&#,$ --# $## #&!A ! DS21733J-page 26 - *;) (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 " )0%!+,-./ . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / D e N E E1 NOTE 1 1 2 3 h b h A2 A c L A1 L1 3# 4# 5$8 %1 44" " 5 5 56 7 ; 1# 6, : # < < ( < < < ( !!1/ / #! %%@ )* ( 6, =!# " !!1/=!# " )* 6, 4# )* * % B . # C #4# 4 . # # 4 . # 9)* ( < ( < ". I > < ;> < ( 4!=!# 8 < ( ! %# D (> < (> ! %#) ## E (> < 4! / (> 1, $!&%#$ , 08$#$ #8 #!-# # # ! @%#* # # !"! #$! !% # $ !% # $ #&!( ! !# "'( )*+ ) #&#,$ --# $## ".+ % 0$ $-# $## 0% % # $ (c) 2009 Microchip Technology Inc. - *() DS21733J-page 27 MCP6001/1R/1U/2/4 " )0%!+,-./ . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / DS21733J-page 28 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 " ( &'(( . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / D N E E1 NOTE 1 1 2 e b A2 A c L L1 A1 3# 4# 5$8 %1 44" " 5 5 56 7 ; 1# 6, : # < < ( ;( ( < ( !!1/ / #! %% 9()* 6, =!# " !!1/=!# " )* 6, 4# )* . #4# 4 . # # 4 . # 4! / )* 9 ; (". I > < ;> ; < 4!=!# 8 < 1, $!&%#$ , 08$#$ #8 #!-# # # ! !"! #$! !% # $ !% # $ #&!( ! !# "'( )*+ ) #&#,$ --# $## ".+ % 0$ $-# $## 0% % # $ (c) 2009 Microchip Technology Inc. - *) DS21733J-page 29 MCP6001/1R/1U/2/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS21733J-page 30 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 12 # / )! -. #/ . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / N NOTE 1 E1 1 3 2 D E A2 A L A1 c b1 b e eB 3# 4# 5$8 %1 5*:" 5 5 1# 7 # #1 56 )* < < ( ( ) # #1 ( < < " ( !!1/ $! # / $! =!# !!1/=!# " ( ; 6, 4# ( ( ( ( # #1 4 ( / ; ( 4!=!# 8 ( 9 8 ; ) < < 4! 3 4 - 4!=!# 6, - @ 1, $!&%#$ , 08$#$ #8 #!-# # # ! @%#* # # !"! #$! !% # $ !% # $ !# "'( )*+) #&#,$ --# $## #&!A ! (c) 2009 Microchip Technology Inc. - *() DS21733J-page 31 MCP6001/1R/1U/2/4 12 )0%!+,-./ . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / D N E E1 NOTE 1 1 2 3 e h b h A2 A c L A1 L1 3# 4# 5$8 %1 44" " 5 5 56 7 1# 6, : # < < ( < < < ( !!1/ / #! %%@ )* 6, =!# " !!1/=!# " )* 6, 4# ;9()* * % B . # C #4# 4 . # # 4 . # ( 9)* ( < ( < ". I > < ;> < ( 4!=!# 8 < ( ! %# D (> < (> ! %#) ## E (> < 4! / (> 1, $!&%#$ , 08$#$ #8 #!-# # # ! @%#* # # !"! #$! !% # $ !% # $ #&!( ! !# "'( )*+ ) #&#,$ --# $## ".+ % 0$ $-# $## 0% % # $ DS21733J-page 32 - *9() (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / (c) 2009 Microchip Technology Inc. DS21733J-page 33 MCP6001/1R/1U/2/4 12 3 3 & )2+2-. . # #$ # /! - 0 # 1/ %# #!# ## +22--- 2 / D N E E1 NOTE 1 1 2 e b c A2 A A1 L L1 3# 4# 5$8 %1 44" " 5 5 56 7 1# 6, : # < < ; ( ( < ( !!1/ / #! %% 9()* 6, =!# " !!1/=!# " !!1/4# ( ( . #4# 4 ( 9 ( . # # 4 . # 4! / 9)* ( ". I > < ;> < 4!=!# 8 < 1, $!&%#$ , 08$#$ #8 #!-# # # ! !"! #$! !% # $ !% # $ #&!( ! !# "'( )*+ ) #&#,$ --# $## ".+ % 0$ $-# $## 0% % # $ DS21733J-page 34 - *;) (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging (c) 2009 Microchip Technology Inc. DS21733J-page 35 MCP6001/1R/1U/2/4 NOTES: DS21733J-page 36 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 APPENDIX A: REVISION HISTORY Revision J (November 2009) Revision G (November 2007) The following is the list of modifications: 1. The following is the list of modifications: 1. Added new 2x3 DFN 8-Lead package on page 1. 2. Updated the Temperature Specifications table with 2x3 DFN thermal resistance information. 3. Updated Section 1.1 "Test Circuits". 4. Updated Figure 2-15. 5. Added the 2x3 DFN column to Table 3-1. 6. Added new Section 3.4 "Exposed Thermal Pad (EP)". 7. Updated Section 5.1 "SPICE Macro Model". 8. Updated Section 5.5 "Analog Demonstration and Evaluation Boards". 9. Updated Section 5.6 "Application Notes". 10. Updated Section 6.1 "Package Marking Information" with the new 2x3 DFN package marking information. 11. Updated the package drawings. 12. Updated the Product Identification System section with new 2x3 DFN package information. 2. 3. 4. 5. 6. 7. 8. 9. Revision F (March 2005) The following is the list of modifications: 1. Revision H (May 2008) The following is the list of modifications: 1. 2. 3. 4. 5. Design Aids: Name change for Mindi Simulation Tool. Package Types: Correct device labeling error. Section 1.0 "Electrical Characteristics", DC Electrical Specifications: Changed "Maximum Output Voltage Swing" condition from 0.9V Input Overdrive to 0.5V Input Overdrive. Section 1.0 "Electrical Characteristics", AC Electrical Specifications: Changed Phase Margin condition from G = +1 to G= +1 V/V. Section 5.0 "Design AIDS": Name change for Mindi Simulation Tool. Updated notes to Section 1.0 "Electrical Characteristics". Increased Absolute Maximum Voltage range at input pins. Increased maximum operating supply voltage (VDD). Added test circuits. Added Figure 2-3 and Figure 2-20. Added Section 4.1.1 "Phase Reversal", Section 4.1.2 "Input Voltage and Current Limits", Section 4.1.3 "Normal Operation" and Section 4.5 "Unused Op Amps". Updated Section 5.0 "Design AIDS", Updated Section 6.0 "Packaging Information" Updated Package Outline Drawings. Updated Section 6.0 "Packaging Information" to include old and new packaging examples. Revision E (December 2004) The following is the list of modifications: 1. 2. 3. VOS specification reduced to 4.5 mV from 7.0 mV for parts starting with date code YYWW = 0449 Corrected package markings in Section 6.0 "Packaging Information". Added Appendix A: Revision History. Revision D (May 2003) * Undocumented changes. Revision C (December 2002) * Undocumented changes. Revision B (October 2002) * Undocumented changes. Revision A (June 2002) * Original data sheet release. (c) 2009 Microchip Technology Inc. DS21733J-page 35 MCP6001/1R/1U/2/4 NOTES: DS21733J-page 36 (c) 2009 Microchip Technology Inc. MCP6001/1R/1U/2/4 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X /XX Device Temperature Range Package Device: MCP6001T: MCP6001RT: MCP6001UT: MCP6002: MCP6002T: MCP6004: MCP6004T: Single Op Amp (Tape and Reel) (SC-70, SOT-23) Single Op Amp (Tape and Reel) (SOT-23) Single Op Amp (Tape and Reel) (SOT-23) Dual Op Amp Dual Op Amp (Tape and Reel) (SOIC, MSOP) Quad Op Amp Quad Op Amp (Tape and Reel) (SOIC, MSOP) Temperature Range: I E = -40C to +85C = -40C to +125C Package: LT = Plastic Package (SC-70), 5-lead (MCP6001 only) OT = Plastic Small Outline Transistor (SOT-23), 5-lead (MCP6001, MCP6001R, MCP6001U) MS = Plastic MSOP, 8-lead MC = Plastic DFN, 8-lead P = Plastic DIP (300 mil body), 8-lead, 14-lead SN = Plastic SOIC, (3.99 mm body), 8-lead SL = Plastic SOIC (3.99 body), 14-lead ST = Plastic TSSOP (4.4mm body), 14-lead Examples: a) MCP6001T-I/LT: Tape and Reel, Industrial Temperature, 5LD SC-70 package b) MCP6001T-I/OT: Tape and Reel, Industrial Temperature, 5LD SOT-23 package. c) MCP6001RT-I/OT: Tape and Reel, Industrial Temperature, 5LD SOT-23 package. d) MCP6001UT-E/OT: Tape and Reel, Extended Temperature, 5LD SOT-23 package. a) MCP6002-I/MS: b) MCP6002-I/P: c) MCP6002-E/P: d) MCP6002-E/MC: e) MCP6002-I/SN: f) MCP6002T-I/MS: g) MCP6002T-E/MC: a) MCP6004-I/P: b) MCP6004-I/SL: c) MCP6004-E/SL: d) MCP6004-I/ST: e) MCP6004T-I/SL: f) (c) 2009 Microchip Technology Inc. MCP6004T-I/ST: Industrial Temperature, 8LD MSOP package. Industrial Temperature, 8LD PDIP package. Extended Temperature, 8LD PDIP package. Extended Temperature, 8LD DFN package. Industrial Temperature, 8LD SOIC package. Tape and Reel, Industrial Temperature, 8LD MSOP package. Tape and Reel, Extended Temperature, 8LD DFN package. Industrial Temperature, 14LD PDIP package. Industrial Temperature, 14LD SOIC package. Extended Temperature, 14LD SOIC package. Industrial Temperature, 14LD TSSOP package. Tape and Reel, Industrial Temperature, 14LD SOIC package. Tape and Reel, Industrial Temperature, 14LD TSSOP package. DS21733J-page 37 MCP6001/1R/1U/2/4 NOTES: DS21733J-page 38 (c) 2009 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, PIC32 logo, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2009, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2009 Microchip Technology Inc. DS21733J-page 39 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4080 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 03/26/09 DS21733J-page 40 (c) 2009 Microchip Technology Inc.