LMC6084
www.ti.com
SNOS657D –AUGUST 2000–REVISED MARCH 2013
LMC6084 Precision CMOS Quad Operational Amplifier
Check for Samples: LMC6084
1FEATURES DESCRIPTION
The LMC6084 is a precision quad low offset voltage
2(Typical Unless Otherwise Stated) operational amplifier, capable of single supply
• Low Offset Voltage: 150 μVoperation. Performance characteristics include ultra
• Operates from 4.5V to 15V Single Supply low input bias current, high voltage gain, rail-to-rail
output swing, and an input common mode voltage
• Ultra Low Input Bias Current: 10 fA range that includes ground. These features, plus its
• Output Swing to within 20 mV of Supply Rail, low offset voltage, make the LMC6084 ideally suited
100k Load for precision circuit applications.
• Input Common-Mode Range Includes V−Other applications using the LMC6084 include
• High Voltage Gain: 130 dB precision full-wave rectifiers, integrators, references,
• Improved Latchup Immunity and sample-and-hold circuits.
This device is built with National's advanced Double-
APPLICATIONS Poly Silicon-Gate CMOS process.
• Instrumentation Amplifier For designs with more critical power demands, see
• Photodiode and Infrared Detector Preamplifier the LMC6064 precision quad micropower operational
amplifier.
• Transducer Amplifiers
• Medical Instrumentation For a single or dual operational amplifier with similar
features, see the LMC6081 or LMC6082 respectively.
• D/A Converter
• Charge Amplifier for Piezoelectric Transducers PATENT PENDING
Connection Diagram
Figure 1. 14-Pin PDIP/SOIC Figure 2. Input Bias Current
Top View vs Temperature
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2000–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LMC6084
SNOS657D –AUGUST 2000–REVISED MARCH 2013
www.ti.com
Absolute Maximum Ratings(1)(2)
Differential Input Voltage ±Supply Voltage
Voltage at Input/Output Pin (V+) +0.3V, (V−)−0.3V
Supply Voltage (V+−V−) 16V
Output Short Circuit to V+See(3)
Output Short Circuit to V−See(4)
Lead Temperature (Soldering, 10 Sec.) 260°C
Storage Temp. Range −65°C to +150°C
Junction Temperature 150°C
ESD Tolerance(5) 2 kV
Current at Input Pin ±10 mA
Current at Output Pin ±30 mA
Current at Power Supply Pin 40 mA
Power Dissipation See(6)
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test
conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
(3) Do not connect output to V+, when V+is greater than 13V or reliability will be adversely affected.
(4) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30 mA over long term may adversely
affect reliability.
(5) Human body model, 1.5 kΩin series with 100 pF.
(6) The maximum power dissipation is a function of TJ(Max),θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD= (TJ(Max) −TA) /θJA.
Operating Ratings(1)
Temperature Range LMC6084AM −55°C ≤TJ≤+125°C
LMC6084AI, LMC6084I −40°C ≤TJ≤+85°C
Supply Voltage 4.5V ≤V+≤15.5V
Thermal Resistance (θJA)(2) 14-Pin PDIP 81°C/W
14-Pin SOIC 126°C/W
Power Dissipation See(3)
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test
conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed.
(2) All numbers apply for packages soldered directly into a PC board.
(3) For operating at elevated temperatures the device must be derated based on the thermal resistance θJA with PD= (TJ−TA)/θJA. All
numbers apply for packages soldered directly into a PC board.
DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ= 25°C. Boldface limits apply at the temperature extremes. V+= 5V,
V−= 0V, VCM = 1.5V, VO= 2.5V and RL> 1M unless otherwise specified. LMC6084AM LMC6084AI LMC6084I
Symbol Parameter Conditions Typ(1) Units
Limit(2) Limit(2) Limit(2)
VOS Input Offset Voltage 150 350 350 800 μV
1000 800 1300 Max
TCVOS Input Offset Voltage 1.0 μV/°C
Average Drift
IBInput Bias Current 0.010 pA
100 4 4 Max
IOS Input Offset Current 0.005 pA
100 2 2 Max
(1) Typical values represent the most likely parametric norm.
(2) All limits are guaranteed by testing or statistical analysis.
2Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC6084
LMC6084
www.ti.com
SNOS657D –AUGUST 2000–REVISED MARCH 2013
DC Electrical Characteristics (continued)
Unless otherwise specified, all limits guaranteed for TJ= 25°C. Boldface limits apply at the temperature extremes. V+= 5V,
V−= 0V, VCM = 1.5V, VO= 2.5V and RL> 1M unless otherwise specified. LMC6084AM LMC6084AI LMC6084I
Symbol Parameter Conditions Typ(1) Units
Limit(2) Limit(2) Limit(2)
RIN Input Resistance >10 Tera Ω
CMRR Common Mode 0V ≤VCM ≤12.0V 85 75 75 66 dB
Rejection Ratio V+= 15V 72 72 63 Min
+PSRR Positive Power Supply 5V ≤V+≤15V 85 75 75 66 dB
Rejection Ratio VO= 2.5V 72 72 63 Min
−PSRR Negative Power Supply 0V ≤V−≤ −10V 94 84 84 74 dB
Rejection Ratio 81 81 71 Min
VCM Input Common-Mode V+= 5V and 15V −0.4 −0.1 −0.1 −0.1 V
Voltage Range for CMRR ≥60 dB 0 0 0 Max
V+−1.9 V+−2.3 V+−2.3 V+−2.3 V
V+−2.6 V+−2.5 V+−2.5 Min
AVLarge Signal RL= 2 kΩ(3) Sourcing 1400 400 400 300 V/mV
Voltage Gain 300 300 200 Min
Sinking 350 180 180 90 V/mV
70 100 60 Min
RL= 600Ω(3) Sourcing 1200 400 400 200 V/mV
150 150 80 Min
Sinking 150 100 100 70 V/mV
35 50 35 Min
VOOutput Swing V+= 5V 4.87 4.80 4.80 4.75 V
RL= 2 kΩto 2.5V 4.70 4.73 4.67 Min
0.10 0.13 0.13 0.20 V
0.19 0.17 0.24 Max
V+= 5V 4.61 4.50 4.50 4.40 V
RL= 600Ωto 2.5V 4.24 4.31 4.21 Min
0.30 0.40 0.40 0.50 V
0.63 0.50 0.63 Max
V+= 15V 14.63 14.50 14.50 14.37 V
RL= 2 kΩto 7.5V 14.30 14.34 14.25 Min
0.26 0.35 0.35 0.44 V
0.48 0.45 0.56 Max
V+= 15V 13.90 13.35 13.35 12.92 V
RL= 600Ωto 7.5V 12.80 12.86 12.44 Min
0.79 1.16 1.16 1.33 V
1.42 1.32 1.58 Max
IOOutput Current Sourcing, VO= 0V 22 16 16 13 mA
V+= 5V 8 10 8 Min
Sinking, VO= 5V 21 16 16 13 mA
11 13 10 Min
IOOutput Current Sourcing, VO= 0V 30 28 28 23 mA
V+= 15V 18 22 18 Min
Sinking, VO= 13V(4) 34 28 28 23 mA
19 22 18 Min
(3) V+= 15V, VCM = 7.5V and RLconnected to 7.5V. For Sourcing tests, 7.5V ≤VO≤11.5V. For Sinking tests, 2.5V ≤VO≤7.5V.
(4) Do not connect output to V+, when V+is greater than 13V or reliability will be adversely affected.
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LMC6084
LMC6084
SNOS657D –AUGUST 2000–REVISED MARCH 2013
www.ti.com
DC Electrical Characteristics (continued)
Unless otherwise specified, all limits guaranteed for TJ= 25°C. Boldface limits apply at the temperature extremes. V+= 5V,
V−= 0V, VCM = 1.5V, VO= 2.5V and RL> 1M unless otherwise specified. LMC6084AM LMC6084AI LMC6084I
Symbol Parameter Conditions Typ(1) Units
Limit(2) Limit(2) Limit(2)
ISSupply Current All Four Amplifiers 1.8 3.0 3.0 3.0 mA
V+= +5V, VO= 1.5V 3.6 3.6 3.6 Max
All Four Amplifiers 2.2 3.4 3.4 3.4 mA
V+= +15V, VO= 7.5V 4.0 4.0 4.0 Max
AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ= 25°C, Boldface limits apply at the temperature extremes. V+= 5V,
V−= 0V, VCM = 1.5V, VO= 2.5V and RL> 1M unless otherwise specified. LMC6084AM LMC6084AI LMC6084I
Symbol Parameter Conditions Typ(1) Units
Limit(2) Limit(2) Limit(2)
SR Slew Rate See(3) 1.5 0.8 0.8 0.8 V/μs
0.5 0.6 0.6 Min
GBW Gain-Bandwidth Product 1.3 MHz
φmPhase Margin 50 Deg
Amp-to-Amp Isolation See(4) 140 dB
enInput-Referred Voltage Noise F = 1 kHz 22 nV/√Hz
inInput-Referred Current Noise F = 1 kHz 0.0002 pA/√Hz
T.H.D. Total Harmonic Distortion F = 10 kHz, AV=−10
RL= 2 kΩ, VO= 8 VPP 0.01 %
±5V Supply
(1) Typical values represent the most likely parametric norm.
(2) All limits are guaranteed by testing or statistical analysis.
(3) V+= 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of the positive and negative slew rates.
(4) Input referred V+= 15V and RL= 100 kΩconnected to 7.5V. Each amp excited in turm with 1 kHz to produce VO= 12 VPP.
4Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC6084
LMC6084
www.ti.com
SNOS657D –AUGUST 2000–REVISED MARCH 2013
Typical Performance Characteristics
Distribution of LMC6084 Distribution of LMC6084
Input Offset Voltage Input Offset Voltage
(TA= +25°C) (TA=−55°C)
Figure 3. Figure 4.
Distribution of LMC6084
Input Offset Voltage Input Bias Current
(TA= +125°C) vs Temperature
Figure 5. Figure 6.
Supply Current Input Voltage
vs Supply Voltage vs Output Voltage
Figure 7. Figure 8.
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LMC6084
LMC6084
SNOS657D –AUGUST 2000–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Common Mode
Rejection Ratio Power Supply Rejection Ratio
vs Frequency vs Frequency
Figure 9. Figure 10.
Input Voltage Noise Output Characteristics
vs Frequency Sourcing Current
Figure 11. Figure 12.
Output Characteristics Gain and Phase Response
Sinking Current vs Temperature (−55°C to +125°C)
Figure 13. Figure 14.
6Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC6084
LMC6084
www.ti.com
SNOS657D –AUGUST 2000–REVISED MARCH 2013
Typical Performance Characteristics (continued)
Gain and Phase Response Gain and Phase Response
vs vs
Capacitive Load with RL= 600ΩCapacitive Load with RL= 500 kΩ
Figure 15. Figure 16.
Open Loop Inverting Small Signal
Frequency Response Pulse Response
Figure 17. Figure 18.
Inverting Large Signal Non-Inverting Small
Pulse Response Signal Pulse Response
Figure 19. Figure 20.
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LMC6084
LMC6084
SNOS657D –AUGUST 2000–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Non-Inverting Large Crosstalk Rejection
Signal Pulse Response vs Frequency
Figure 21. Figure 22.
Stability Stability
vs vs
Capacitive Load, RL= 600ΩCapacitive Load RL= 1 MΩ
Figure 23. Figure 24.
8Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC6084
LMC6084
www.ti.com
SNOS657D –AUGUST 2000–REVISED MARCH 2013
APPLICATIONS HINTS
AMPLIFIER TOPOLOGY
The LMC6084 incorporates a novel op-amp design topology that enables it to maintain rail-to-rail output swing
even when driving a large load. Instead of relying on a push-pull unity gain output buffer stage, the output stage
is taken directly from the internal integrator, which provides both low output impedance and large gain. Special
feed-forward compensation design techniques are incorporated to maintain stability over a wider range of
operating conditions than traditional micropower op-amps. These features make the LMC6084 both easier to
design with, and provide higher speed than products typically found in this ultra-low power class.
COMPENSATING FOR INPUT CAPACITANCE
It is quite common to use large values of feedback resistance for amplifiers with ultra-low input current, like the
LMC6084.
Although the LMC6084 is highly stable over a wide range of operating conditions, certain precautions must be
met to achieve the desired pulse response when a large feedback resistor is used. Large feedback resistors and
even small values of input capacitance, due to transducers, photodiodes, and circuit board parasitics, reduce
phase margins.
When high input impedances are demanded, guarding of the LMC6084 is suggested. Guarding input lines will
not only reduce leakage, but lowers stray input capacitance as well. (See Printed-Circuit-Board Layout for High
Impedance Work)
The effect of input capacitance can be compensated for by adding a capacitor, Cf, around the feedback resistors
(as in Figure 25 ) such that:
(1)
or (2)
R1CIN ≤R2Cf(3)
Since it is often difficult to know the exact value of CIN, Cfcan be experimentally adjusted so that the desired
pulse response is achieved. Refer to the LMC660 and LMC662 for a more detailed discussion on compensating
for input capacitance.
Figure 25. Cancelling the Effect of Input Capacitance
CAPACITIVE LOAD TOLERANCE
All rail-to-rail output swing operational amplifiers have voltage gain in the output stage. A compensation capacitor
is normally included in this integrator stage. The frequency location of the dominant pole is affected by the
resistive load on the amplifier. Capacitive load driving capability can be optimized by using an appropriate
resistive load in parallel with the capacitive load (see typical curves).
Direct capacitive loading will reduce the phase margin of many op-amps. A pole in the feedback loop is created
by the combination of the op-amp's output impedance and the capacitive load. This pole induces phase lag at the
unity-gain crossover frequency of the amplifier resulting in either an oscillatory or underdamped pulse response.
With a few external components, op amps can easily indirectly drive capacitive loads, as shown in Figure 26.
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LMC6084
LMC6084
SNOS657D –AUGUST 2000–REVISED MARCH 2013
www.ti.com
Figure 26. LMC6084 Noninverting Gain of 10 Amplifier, Compensated to Handle Capacitive Loads
In the circuit of Figure 26, R1 and C1 serve to counteract the loss of phase margin by feeding the high frequency
component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the
overall feedback loop.
Capacitive load driving capability is enhanced by using a pull up resistor to V+Figure 27. Typically a pull up
resistor conducting 500 μA or more will significantly improve capacitive load responses. The value of the pull up
resistor must be determined based on the current sinking capability of the amplifier with respect to the desired
output swing. Open loop gain of the amplifier can also be affected by the pull up resistor (see Electrical
Characteristics).
Figure 27. Compensating for Large Capacitive Loads with a Pull Up Resistor
PRINTED-CIRCUIT-BOARD LAYOUT FOR HIGH-IMPEDANCE WORK
It is generally recognized that any circuit which must operate with less than 1000 pA of leakage current requires
special layout of the PC board. When one wishes to take advantage of the ultra-low bias current of the
LMC6084, typically less than 10 fA, it is essential to have an excellent layout. Fortunately, the techniques of
obtaining low leakages are quite simple. First, the user must not ignore the surface leakage of the PC board,
even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or
contamination, the surface leakage will be appreciable.
To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the LMC6084's inputs
and the terminals of capacitors, diodes, conductors, resistors, relay terminals, etc. connected to the op-amp's
inputs, as in Figure 28. To have a significant effect, guard rings should be placed on both the top and bottom of
the PC board. This PC foil must then be connected to a voltage which is at the same voltage as the amplifier
inputs, since no leakage current can flow between two points at the same potential. For example, a PC board
trace-to-pad resistance of 1012Ω, which is normally considered a very large resistance, could leak 5 pA if the
trace were a 5V bus adjacent to the pad of the input. This would cause a 100 times degradation from the
LMC6084's actual performance. However, if a guard ring is held within 5 mV of the inputs, then even a
resistance of 1011Ωwould cause only 0.05 pA of leakage current. See Figure 29 for typical connections of guard
rings for standard op-amp configurations.
10 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC6084
LMC6084
www.ti.com
SNOS657D –AUGUST 2000–REVISED MARCH 2013
Figure 28. Example of Guard Ring in P.C. Board Layout
Inverting Amplifier
Non-Inverting Amplifier
Follower
Figure 29. Typical Connections of Guard Rings
The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few
circuits, there is another technique which is even better than a guard ring on a PC board: Don't insert the
amplifier's input pin into the board at all, but bend it up in the air and use only air as an insulator. Air is an
excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but
the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 30.
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LMC6084
LMC6084
SNOS657D –AUGUST 2000–REVISED MARCH 2013
www.ti.com
Latchup
CMOS devices tend to be susceptible to latchup due to their internal parasitic SCR effects. The (I/O) input and
output pins look similar to the gate of the SCR. There is a minimum current required to trigger the SCR gate
lead. The LMC6084 is designed to withstand 100 mA surge current on the I/O pins. Some resistive method
should be used to isolate any capacitance from supplying excess current to the I/O pins. In addition, like an SCR,
there is a minimum holding current for any latchup mode. Limiting current to the supply pins will also inhibit
latchup susceptibility.
(Input pins are lifted out of PC board and soldered directly to components. All other pins connected to PC board).
Figure 30. Air Wiring
Typical Single-Supply Applications
(V+= 5.0 VDC)
The extremely high input impedance, and low power consumption, of the LMC6084 make it ideal for applications
that require battery-powered instrumentation amplifiers. Examples of these types of applications are hand-held
pH probes, analytic medical instruments, magnetic field detectors, gas detectors, and silicon based pressure
transducers.
Figure 31 shows an instrumentation amplifier that features high differential and common mode input resistance
(>1014Ω), 0.01% gain accuracy at AV= 1000, excellent CMRR with 1 kΩimbalance in bridge source resistance.
Input current is less than 100 fA and offset drift is less than 2.5 μV/°C. R2provides a simple means of adjusting
gain over a wide range without degrading CMRR. R7is an initial trim used to maximize CMRR without using
super precision matched resistors. For good CMRR over temperature, low drift resistors should be used.
If R1= R5, R3= R6, and R4= R7; then
12 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC6084
LMC6084
www.ti.com
SNOS657D –AUGUST 2000–REVISED MARCH 2013
∴AV≈100 for circuit shown (R2= 9.822k).
Figure 31. Instrumentation Amplifier
Figure 32. Low-Leakage Sample and Hold
Figure 33. 1 Hz Square Wave Oscillator
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LMC6084
LMC6084
SNOS657D –AUGUST 2000–REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision C (March 2013) to Revision D Page
• Changed layout of National Data Sheet to TI format .......................................................................................................... 13
14 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC6084
PACKAGE OPTION ADDENDUM
www.ti.com 30-Sep-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LMC6084AIM/NOPB ACTIVE SOIC D 14 55 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC6084
AIM
LMC6084AIMX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC6084
AIM
LMC6084IM/NOPB ACTIVE SOIC D 14 55 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC6084IM
LMC6084IMX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC6084IM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 30-Sep-2017
Addendum-Page 2
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LMC6084AIMX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1
LMC6084IMX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 5-Dec-2014
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LMC6084AIMX/NOPB SOIC D 14 2500 367.0 367.0 35.0
LMC6084IMX/NOPB SOIC D 14 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 5-Dec-2014
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
