MP2-SS168-51S2-TG - 3M - Pdf.Support

3M

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ MetPak™ 2-FB Stacking Socket

2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail MP2 Series

Physical

Electrical

Environmental

MetPak is a trademark of 3M Company.

* Futurebus+ is a registered trademark of the Institute of Electrical and Electronic Engineers, Inc. (IEEE).

Insulation

Material: High Temp LCP

Flammability: UL 94V-0

Color: Beige

Contact

Material: Phosphor Bronze

Plating

Underplating: 50 μ″ [ 1.27 μm ] Nickel

Wiping Area: See Ordering Information

Solder Tails: See Ordering Information

Current Rating: Signal: 1.5 A - All contacts simultaneously

Insulation Resistance: 103 MΩ

Withstanding Voltage: 1000 VAC

Temperature Rating: -55°C to +125°C

Process Temperature Rating: 260°C (Profile per J-STD-020C)

Moisture Sensitivity Level: 1 (per J-STD-020C)

TS-1118-05

Sheet 1 of 3

Date Modified: March 27, 2007

• End-to-end stackable

• Offset dual-beam contact minimizes

insertion force

• High-profile/high pin count

• Ideal for parallel stacking applications

• Vertical receptacle

• Eliminates internal cabling

• Meets IEC 61076-4-104 Futurebus+®

global standard

• See Regulatory Information Appendix (RIA)

for chemical compliance information

3M

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ MetPak™ 2-FB Stacking Socket

2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail MP2 Series

TS-1118-05

Sheet 2 of 4

MP2 - SSXXX - X1XX - XXXXX

Ordering Information

Stacking

Socket Contact Count

(See Table 1)

Rows

4 = 4 Rows

5 = 5 Rows

Termination Style

P = Press-Fit (w/Tail Cover)

S = Solder Tail

Tail Length

(See Table 2)

*Contact Customer Service for information on special fill patterns.

SOLDER TAIL OR PRESS-FIT

ROW

X 2

POSITION

C

D

E

A

B

1

"A"

"B"

3.02

.119

2.00

.079 TYP.

4 ROW PRODUCT

MATED WITH MP2-HXXX-XXXX-XXXX

5 ROW PRODUCT

20.00 ±.38

.787 ±.015

MP2-HXXX-XXXX-XXXX

MP2-SSXXX-X1XX-XXXX

"C" TAIL LENGTH

3.63

.143

8.00

.315

2.00

.079 4X

16.50

.650

14.50

.571

3.63

.143

2.00

.079 3X

6.00

.236

0.63

.025

Plating Options:

(See Table 3)

Note:

1. Refer to IEC 61076-4-104 Futurebus+® global standard.

2. "Press Fit" describes a contact tail having a compliant section designed to make a reliable electrical connection with a

plated through-hole (PTH) in a printed circuit board, typically a "back plane.”

0 0.0 0.00

mm ±3 ±0.3 ±0.13

mm

[inch]

Tolerance Unless Noted

[ ] Dimensions for Reference Only

3M

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ MetPak™ 2-FB Stacking Socket

2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail MP2 Series

TS-1118-05

Sheet 3 of 4

Plating

Suffix Press-Fit Tails* Solder Tails Plating Composition

0.25 µm [10 µ"] Min. Au Contact Area

2.54 µm [100 µ"] Min. SnPb Tail Area

1.27 µm [50 µ"] Min. Ni all over

0.76 µm [30 µ"] Min. Au Contact Area

2.54 µm [100 µ"] Min. SnPb Tail Area

1.27 µm [50 µ"] Min. Ni all over

0.08 µm [3 µ"] Min. Au Contact Area

0.67 µm [27 µ"] Min. PdNi Contact Area

2.54 µm [100 µ"] Min. SnPb Tail Area

1.27 µm [50 µ"] Min. Ni all over

0.13 µm [5 µ"] Min. Hard Au Contact Area, Lubricated

1.02 µm [40 µ"] Min. PdNi Contact Area

0.10 µm [4 µ"] Min. Pd Contact Area

2.54 µm [100 µ"] Min. SnPb Tail Area

1.27 µm [50 µ"] Min. Ni all over

0.25 µm [10 µ"] Min. Au Contact Area

5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area

1.27 µm [50 µ"] Min. Ni all over

0.76 µm [30 µ"] Min. Au Contact Area

5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area

1.27 µm [50 µ"] Min. Ni all over

1.27 µm [50 µ"] Min. Au Contact Area, Lubricated

5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area

1.27 µm [50 µ"] Min. Ni all over

0.08 µm [3 µ"] Min. Au Contact Area

0.67 µm [27 µ"] Min. PdNi Contact Area

5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area

1.27 µm [50 µ"] Min. Ni all over

0.13 µm [5 µ"] Min. Hard Au Contact Area, Lubricated

1.02 µm [40 µ"] Min. PdNi Contact Area

0.10 µm [4 µ"] Min. Pd Contact Area

5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area

1.27 µm [50 µ"] Min. Ni all over

*Compliant-Pin Tail

KR

RF

Table 3 - Plating & Regulatory

TG

TG30

TR30

RIA E2 & C2

apply

RIA E3 & C2

apply

RIA E1 & C1

apply

RIA E1 & C1

apply

LR

PD

RIA E2 & C2

apply

RIA E3 & C2

apply

RIA E2 & C2

apply

RIA E3 & C2

apply

RIA E2 & C2

apply

RIA E3 & C2

apply

TR40B

FJ

RIA E1 & C1

apply

RIA E1 & C1

apply

RIA E1 & C1

apply

RIA E1 & C1

apply

RIA E1 & C1

apply

RIA E1 & C1

apply

RIA E1 & C1

apply

RIA E1 & C1

apply

Pin

Count Rows

Block

Count

024 11.95 [0.471] 10.00 [0.394] 4 1

048 23.95 [0.943] 22.00 [0.866] 4 2

072 35.95 [1.415] 34.00 [1.339] 4 3

096 47.95 [1.889] 46.00 [1.811] 4 4

120 59.95 [2.36] 58.00 [2.283] 4 5

144 71.95 [2.833] 70.00 [2.756] 4 6

168 83.95 [3.305] 82.00 [3.228] 4 7

192 95.95 [3.778] 94.00 [3.701] 4 8

030 11.95 [0.471] 10.00 [0.394] 5 1

060 23.95 [0.943] 22.00 [0.866] 5 2

090 35.95 [1.415] 34.00 [1.339] 5 3

120 47.95 [1.888] 46.00 [1.811] 5 4

150 59.95 [2.361] 58.00 [2.283] 5 5

180 71.95 [2.833] 70.00 [2.756] 5 6

210 83.95 [3.305] 82.00 [3.228] 5 7

240 95.95 [3.778] 94.00 [3.701] 5 8

Table 1 - Connector & Row Lengths

Dim. "A"

mm [inch]

Dim "B"

mm [inch]

Solder Press-Fit*

2 2.72 [0.107]

1 1 3.53 [0.139]

*Compliant-Pin Tail

Table 2 - Tail Length

Contact-to-PC Board Tail

Termination Option No. Dim. "C"

3M

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ MetPak™ 2-FB Stacking Socket

2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail MP2 Series

RECOMMENDED 5 ROW PRESS-FIT

PCB HOLE MOUNTING PATTERN

RECOMMENDED 5 ROW SOLDER

TAIL PCB HOLE MOUNTING PATTERN

lO0.10

lO0.10

A1

8.00

.315

2.00

.079 4X

2.00

.079

14.00

.551

2.00

.079

TYP.

"B"

"D" PLATED THRU HOLE

O1.50 +.10

-.00

.059 +.004

-.000

UNPLATED THRU HOLE

RECOMMENDED 4 ROW SOLDER

TAIL PCB HOLE MOUNTING PATTERN

RECOMMENDED 4 ROW PRESS-FIT

PCB HOLE MOUNTING PATTERN

lO0.10

lO0.10

A1

2.00

.079

6.00

.236

12.00

.472

2.00

.079 3X

"D" PLATED THRU HOLE

2.00

.079

TYP.

"B"

O1.50 +.10

-.00

.059 +.004

-.000

UNPLATED THRU HOLE

TS-1118-05

Sheet 4 of 4

HOLE Finished Dia.

mm [in]

Cu Thickness

mm [in]

SnPb Thickness

microns [µ"]

Drilled Hole Dia.

mm [in]

"D" 0.65-0.80 [.0256-.0315] 0.025 [.001] min 15 [600] max 0.81-0.86 [.0319-.0339]

Table 4 -- HOLE PLATING For TG, TG30, TR30, TR40B FINISHES ONLY

Hole Finished Dia.

mm [in]

Cu Thickness

mm [in]

Immersion Matte Sn

Thickness

microns [µ"]

Electrolitic Au

Thickness

microns [µ"]

OSP ENTEK

Thickness

microns [µ"]

Drilled Hole Dia.

mm [in]

0.700-0.800 0.025-0.045 0.5 - 2.5 0.1 - 0.5 0.2 - 0.5 0.830-0.860 [.0330-.0340] or

[.0276-.0315] [0.001-0.002] [20 - 100] [4 - 20] [8 - 20] 0.85mm [ #66] TWIST DRILL

Table 5 -- HOLE PLATING For FJ, KR, RF, LR, and PD FINISHES ONLY

"D"

“D” PLATED THROUGH-HOLE

UNPLATED THROUGH-HOLE

“D” PLATED THROUGH-HOLE

UNPLATED THROUGH-HOLE

Regulatory Information Appendix

3M Electronic Solutions Division/Interconnect

EUROPE

Appendix E1: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product is RoHS Compliant 2005/95/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in

excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/

EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E2: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/747/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in

excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/

EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E3: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as

amended by Commission Decision 2005/618/EC.

This product contains lead in the solder tail area in excess of the maximum concentration value allowed.

Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon

information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E4: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/17/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in

excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision

2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in

writing, this information represents 3M’s best knowledge and belief based upon information provided by third party

suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

RIA-2217-A

CHINA

Appendix C1: China RoHS

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits

for Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,

means that the product or part does not contain any of the following substances in excess of the following maximum

concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,

polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise

stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by

third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix C2: China RoHS

20

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits

for Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,

means that the product or part does contain a substance, as detailed in the chart below, in excess of the following

maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent

chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless

otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information

provided by third party suppliers to 3M.

The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an

extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform

with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in

accordance with the product Warranty stated below.

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the

accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended

application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s

current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in

writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3M MAKES NO

OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s

option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for

any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

Name and Content of Hazardous Substances or Elements

3

Electronic Solutions Division

6801 River Place Blvd.

Austin, TX 78726-9000

800/225-5373

www.3M.com/interconnects RIA-2217-A

© 3M 2007