PLM-12 12W Single Output LED Power Supply series Features : Universal AC input / Full range(up to 295VAC) Protections:Short circuit Cooling by free air convection Fully isolated plastic case Built-in active PFC function Small and compact size Class power unit, no FG Class 2 power unit 100% full load burn-in test No load power consumption <0.5W High reliability,low cost Suitable for LED lighting and moving sign applications 2 years warranty M SPECIFICATION 110 SELV 18 IP30 PLM-12-500 PLM-12-700 PLM-12-1050 LED OPERATION VOLTAGE Note.5 22 ~ 36V 0.35A RATED CURRENT 15 ~ 24V 11 ~ 18V 7 ~ 12V 0.5A 0.7A 1.05A NO-LOAD OUTPUT VOLTAGE(max.) 42V 12.6W RATED POWER 30V 12W 22V 12.6W 16V 12.6W RIPPLE & NOISE (max.) Note.2 3.6Vp-p 2.4Vp-p 2.4Vp-p 1.8Vp-p PLM-12-350 MODEL OUTPUT F M CURRENT ACCURACY Note.3 5.0% SETUP TIME 500ms / 115VAC, 230VAC at full load VOLTAGE RANGE INPUT Note.4 110 ~ 295VAC 47 ~ 63Hz POWER FACTOR PF0.97/115VAC,PF0.95/230VAC,PF>0.9/277VAC(at full load)(Please refer to "Power Factor Characteristic" curve) 85% 81% 84% 83% 0.15A/115VAC 0.08A/230VAC 0.07A/277VAC EFFICIENCY(Typ.) AC CURRENT INRUSH CURRENT(Typ.) LEAKAGE CURRENT PROTECTION SHORT CIRCUIT WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT SAFETY & EMC OTHERS COLD START 15A(twidth=50s measured at 50% Ipeak) at 230VAC 0.25mA / 240VAC Hiccup mode, recovers automatically after fault condition is removed. -30 ~ +50 20 ~ 90% RH non-condensing -40 ~ +80, 10 ~ 95% RH 0.06%/ (0 ~ 50) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS UL8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1, EN61347-2-13, EN62384, IP30 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC I/P-O/P:100M Ohms/500VDC / 25/ 70%RH Compliance to EN55015,EN61000-3-2 Class C(60% load);EN61000-3-3 ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF DIMENSION PACKING NOTE 156 ~ 416VDC FREQUENCY RANGE Compliance to EN61000-4-2,3,4,5,6,8,11;EN61547, light industry level, criteria A(surge 2KV) 808.162Khrs min. MIL-HDBK-217F (25) 145*38*22mm (L*W*H) 0.126Kg;60pcs/8.6 Kg/0.48CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Please see "AC input voltage drop vs. output current characteristics" table. 4. Derating may be needed under low input voltage, please check the static characteristic for more details. 5. Constant current operation region is within 60% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. File Name:PLM-12-SPEC 2014-03-07 PLM-12 12W Single Output LED Power Supply Mechanical Specification series Case No.PLM-25 Unit:mm 145 4.5 3.5 4.5 1 2 38 4.5 2 T case 1 12 65 TB1 TB2 4.5 22 3.5 T case: Max. Case Temperature. NOTE: The input and output line for using UL1015 18AWG*2C is suggested Terminal Pin No. Assignment (TB1) : SWITCHLAB MWX201-75002EB(GRAY) Pin No. 1 2 Terminal Pin No. Assignment (TB2) : SWITCHLAB MWX201-75002B(BLUE) Assignment AC/L AC/N Pin No. 1 2 Assignment +V -V Block Diagram I/P EMI FILTER POWER SWITCHING RECTIFIERS RECTIFIERS & FILTER +V -V PWM /PFC CONTROL Derating Curve Static Characteristics 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -30 -25 -5 0 15 30 40 AMBIENT TEMPERATURE () 50 60 (HORIZONTAL) 60 50 40 110 120 125 135 145 155 165 175 180 200 230 295 INPUT VOLTAGE (V) File Name:PLM-12-SPEC 2014-03-07 PLM-12 12W Single Output LED Power Supply series Power Factor Characteristic Constant Current Mode 1.02 1 0.98 0.96 PF 0.94 0.92 110V 0.9 230V 0.88 277V 0.86 0.84 0.82 0.8 50% 60% 70% 80% 90% 100% (12W) LOAD EFFICIENCY vs LOAD (500mA Model) 86 EFFICIENCY (%) 85 84 83 110V 230V 82 277V 81 80 79 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD AC input voltage drop vs. output current characteristics AC input drop Io drop 10% 8% 5% 3% <15% <11% <7% <6% NOTE: Output current will return to the rated value within 50ms File Name:PLM-12-SPEC 2014-03-07 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Mean Well: PLM-12-350 PLM-12-500 PLM-12-700 PLM-12-1050