VOD205T, VOD206T, VOD207T, VOD211T, VOD213T, VOD217T
www.vishay.com Vishay Semiconductors
Rev. 1.2, 23-Nov-12 1Document Number: 81956
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Optocoupler, Phototransistor Output, Dual Channel,
SOIC-8 Package
DESCRIPTION
The VOD205T, VOD206T, VOD207T, VOD211T, VOD213T,
VOD217T are optically coupled pairs with a gallium arsenide
infrared LED and a silicon NPN phototransistor. Signal
information, including a DC level, can be transmitted by the
device while maintaining a high degree of electrical isolation
between input and output.
FEATURES
• Two channel coupler
• SOIC-8 surface mountable package
• Standard lead spacing of 0.05"
• Available only on tape and reel option
(conforms to EIA standard 481-2)
• Isolation test voltage, 4000 VRMS
• Compatible with dual wave, vapor phase and IR reflow
soldering
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
AGENCY APPROVALS
• UL1577, file no. E52744 system code Y
• cUL - file no. E52744, equivalent to CSA bulletin 5A
• DIN EN 60747-5-5 (VDE 0884-5) approved, contact
customer service if this option is required
Notes
(1) IF = 10 mA
(2) IF = 1 mA
i179018-1
A1
C2
A3
C4
8C
7E
6C
5E
V
DE
i179074
ORDERING INFORMATION
VOD2 # # T
PART NUMBER
AGENCY CERTIFIED/PACKAGE CTR (%)
UL, cUL 40 to 80 63 to 125 100 to 200 > 20 > 100 (1) > 100 (2)
SOIC-8
VOD205T VOD206T VOD207T VOD211T VOD213T VOD217T
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
INPUT
Peak reverse voltage VR6V
Peak pulsed current 1 μs, 300 pps IFM 1A
Continuous forward current per channel IF30 mA
Power dissipation Pdiss 50 mW
Derate linearly from 25 °C 0.66 mW/°C
OUTPUT
Collector emitter breakdown voltage BVCEO 70 V
Emitter collector breakdown voltage BVECO 7V
Continuous output current ICmax. 50 mA
Power dissipation per channel Pdiss 125 mW
Derate linearly from 25 °C 1.67 mW/°C
SIOC-8
6.1 mm
VOD205T, VOD206T, VOD207T, VOD211T, VOD213T, VOD217T
www.vishay.com Vishay Semiconductors
Rev. 1.2, 23-Nov-12 2Document Number: 81956
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
(1) Refer to reflow profile for soldering conditions for surface mounted devices.
Fig. 1 - Power Dissipation vs. Ambient Temperature
Note
• Minimum and maximum values were tested requierements. Typical values are characteristics of the device and are the result of engineering
evaluations. Typical values are for information only and are not part of the testing requirements.
COUPLER
Isolation test voltage t = 1 s VISO 4000 VRMS
Total package dissipation ambient
(2 LEDs and 2 detectors, 2 channels) Ptot 300 mW
Derate linearly from 25 °C 4mW/°C
Storage temperature Tstg -40 to +150 °C
Operating temperature Tamb -40 to +100 °C
Soldering time from 260 °C (1) Tsld 10 s
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
iild205t_07
200
150
100
50
0
TA- Ambient Temperature (°C)
Package Power Dissipation (mW)
25 50 75 100 125
total pkg
per channel
ELECTRICAL CHARACTERISTCS (Tamb = 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT
INPUT
Forward voltage IF = 10 mA VF1.2 1.55 V
Reverse current VR = 6 V IR0.1 100 μA
Capacitance VR = 0 V CO25 pF
OUTPUT
Collector emitter breakdown voltage IC = 100 μA BVCEO 70 V
Emitter collector breakdown voltage IE = 100 μA BVECO 7V
Collector emitter leakage current VCE = 10 V, IF = 0 A ICEO 550nA
Collector emitter capacitance VCE = 0 V CCE 10 pF
Collector emitter saturation voltage IF = 10 mA, IC = 2.5 mA VCEsat 0.4 V
COUPLER
Capacitance (input to output) CIO 0.5 pF
VOD205T, VOD206T, VOD207T, VOD211T, VOD213T, VOD217T
www.vishay.com Vishay Semiconductors
Rev. 1.2, 23-Nov-12 3Document Number: 81956
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fig. 2 - Switching Test Circuit
CURRENT TRANSFER RATIO
PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT
IC/IF
VCE = 5 V, IF = 10 mA
VOD205T CTRDC 40 80 %
VOD206T CTRDC 63 125 %
VOD207T CTRDC 100 200 %
VOD211T CTRDC 20 %
VOD213T CTRDC 100 %
VCE = 5 V, IF = 1 mA
VOD205T CTRDC 13 30 %
VOD206T CTRDC 22 45 %
VOD207T CTRDC 34 70 %
VOD217T CTRDC 100 120 %
SWITCHING CHARACTERISTICS
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Turn-on time IC = 2 mA, RL = 100 Ω, VCC = 5 V ton 5μs
Turn-off time IC = 2 mA, RL = 100 Ω, VCC = 5 V toff 4μs
Rise time IC = 2 mA, RL = 100 Ω, VCC = 5 V tr5μs
Fall time IC = 2 mA, RL = 100 Ω, VCC = 5 V tf4μs
COMMON MODE TRANSIENT IMMUNITY
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Common mode transient immunity
at logic high
VCM = 1000 VP-P, RL = 1 kΩ,
IF = 0 mA |CMH| 10 000 V/μs
Common mode transient immunity
at logic low
VCM = 1000 VP-P, RL = 1 kΩ,
IF = 10 mA |CML| 10 000 V/μs
iil215at_17
VCC = 5 V
Input
VOUT
RLtfall
10 %
50 %
90 %
toff
ton
trise
Output
Input
10 %
50 %
90 %
V0
0
VOD205T, VOD206T, VOD207T, VOD211T, VOD213T, VOD217T
www.vishay.com Vishay Semiconductors
Rev. 1.2, 23-Nov-12 4Document Number: 81956
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fig. 3 - Test Circuit for Common Mode Transient Immunity
Note
• As per IEC 60747-5-5, §7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with
the safety ratings shall be ensured by means of protective circuits.
RF
VB = 4.5 V
1, 2, 4
3
B
A6
5
RL
1 K
VO
5 VDC
0.1 µF
VCM
Input from HV pulse source
+
-
21628
dt dt
dV = 63 % of V
CM
dV = 63 % of V
CM
Common mode
voltage V
CM
2.0 V 2.0 V
V
O
V
O
CM
H
CM
L
0.8 V 0.8 V
Time
21626
SAFETY AND INSULATION RATINGS
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Climatic classification according to IEC 68 part 1 40/100/21
Polution degree 2
Comparative tracking index CTI 175 399
Peak transient overvoltage VIOTM 6000 V
Peak insulation voltage VIORM 560 V
Resistance (input to output) RIO 100 GΩ
Apparent charge method a qpd C
Apparent charge method b qpd C
Safety rating - power output PSO 350 mW
Safety rating - input current ISI 150 mA
Safety rating - temperature TSI 165 °C
External creepage distance 4 mm
Internal creepage distance 4 mm
External clearance distance 4 mm
Insulation thickness 0.2 mm
VOD205T, VOD206T, VOD207T, VOD211T, VOD213T, VOD217T
www.vishay.com Vishay Semiconductors
Rev. 1.2, 23-Nov-12 5Document Number: 81956
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Fig. 4 - Forward Current vs. Forward Voltage
Fig. 5 - Collector Emitter Current vs. VCE
Fig. 6 - Normalized CTRCE vs. Forward Current
Fig. 7 - Current Transfer Ratio (normalized) vs.
Ambient Temperature
Fig. 8 - Switching Speed vs. Load Resistor
Fig. 9 - Collector Current vs. Ambient Temperature
30
25 85 °C
60 °C
25 °C
20
10
5
0
15
0.6 1.00.8 1.2 1.4
iild205t_01
V
F
- LED Forward Voltage (V)
I
F
- LED Current (mA)
iild205t_02
0 6 10 12
1.2
1.0
0.8
0.6
0.4
0.2
0.0
V
CE - Collector To Emitter Voltage (V)
NIc Normalized Collector Current
IF= 10 mA
IF= 5 mA
IF= 1 mA
Coll Current Normalized at I = 10 mA
F
VCE = 10 V
42 8
iild205t_03
NCTR
CE
- Normalized CTR
CE
0.01 0.1 1 10 100
1.2
1.0
0.8
0.6
0.4
0.2
0.0
IF- LED Current (mA)
V
CE = 5 V
CTR normalized at
IF= 10 mA
V
CE = 0.4 V
iild205t_04
20 40 60 80 100
1.2
1.0
0.8
0.6
0.4
0.2
0.0
T
A- Temperature (°C)
NCTR
ce
- Normalized CTR
ce
I
F
= 5 mA
I
F
= 1 mA
I
F
= 10 mA
CTR nonsat normalized at
I
F
= 10 mA
V
CE
= 10 V
iild205t_05
Switching Speed (µs)
0.1 1 10 100
10
3
10
2
10
1
10
0
R
L
- Load Resistor (kΩ)
I
F
= 10 mA
Pulse Width = 100 ms
Duty Cycle = 50 % t
off
t
on
0.001
0.01
Iceo - Leakage Current (μA)
0.1
1
20 60 1008040
TA - Temperature (°C)
iild205t_06
VCE = 50 V
VCE = 10 V
VOD205T, VOD206T, VOD207T, VOD211T, VOD213T, VOD217T
www.vishay.com Vishay Semiconductors
Rev. 1.2, 23-Nov-12 6Document Number: 81956
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PACKAGE DIMENSIONS in millimeters
PACKAGE MARKING (example of VOD207T)
TAPE AND REEL PACKAGING
Dimensions in millimeters
Fig. 10 - Tape and Reel Shipping Medium
(EIA-481, revision A, and IEC 60286), 2000 units per reel
Fig. 11 - Tape Dimensions, 2000 Parts per Reel
0.91
0.36
4.32 1.14
6.6
R 0.13
1.27
i178020
ISO method A
40°
6.10
1.27 typ.
0.41
0.1
0.2
Lead coplanarity
± 0.001 max.
0.20
7°
3.05 ± 0.05
CL
R 0.25 max.
1.02
5° max.
Pin one ID
3.91 ± 0.05
0.38 ± 0.05
5.84 ± 0.05
0.51 ± 0.10
2 plcs.
1.49 ± 0.05
3.18 ± 0.05
D207
V YWW Y 68
ESD sticker
Tape slot
in core
330
(13")
Regular, special
or bar code label
17999
18004-1
1.5
1.75 ± 0.1
13.3
0.3 max.
0.1 max.
16.0 ± 0.3
4 ± 0.1
2 ± 0.05
6.6
6.35
8.0
7.5 ± 0.05
3.8
Embossment
Direction of feed
Center lines
of cavity
10 pitch cumulative
tolerance on tape
± 0.2
1.5 min.
Pin 1 and
top of component
Top
cover
tape
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 08-Feb-17 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
