Multilayer Ceramic Chip Capacitors Kyocera's series of Multilayer Ceramic Chip Capacitors are designed to meet a wide variety of needs. We offer a complete range of products for both general and specialized applications, including CM series for generalpurpose, CT series for low profile, CU series for Hi-Q, AT series for Au termination, ST series for soft termination, and CF series for high-voltage. Features * We have a network worldwide in order to supply our global customer bases quickly and efficiently and to maintain our reputation as one of the highest-volume producers in the industry. * All our products are highly reliable due to their monolithic structure of high-purity and superfine uniform ceramics and their integral internal electrodes. * By combining superior manufacturing technology and materials with high dielectric constants, we produce extremely compact components with exceptional specifications. * Our stringent quality control in every phase of production from material procurement to shipping ensures consistent manufacturing and super quality. * Kyocera components are available in a wide choice of dimensions, temperature characteristics, rated voltages, and terminations to meet specific configurational requirements. RoHS Compliant CF CM series High-Voltage ST series General Multilayer series Ceramic Chip Soft Termination Capacitors AT series Au Termination CT series Low Profile CU series High-Q Structure External Termination Electrodes Internal Electrodes (Pd, Pd/ Ag or Ni or Cu) Dielectric Ceramic Layer Temperature compensation: Titanate family Zirconate family High dielectric constant: Barium Titanate family Tape and Reel Nickel Barrier Termination Products Ag or Cu or CuNi Ni Plating Sn or Au or Cu Plating Bulk Case Please contact your local AVX, Kyocera sales office or distributor for specifications not covered in this catalog. Our products are continually being improved. As a result, the capacitance range of each series is subject to change without notice. Please contact an sales representative to confirm compatibility with your application. Multilayer Ceramic Chip Capacitors Kyocera Ceramic Chip Capacitors are available for different applications as classified below: Series Dielectric Options Typical Applications Features Terminations Available Size CM C0G (NP0) X5R X7R X6S X7S General purpose Wide cap range Nickel barrier/ Tin 01005, 0201, 0402 0603, 0805, 1206 1210, 1812 CT X5R X7R IC card (Decoupling) Low profile Nickel barrier/ Tin 0201, 0402, 0603 0805, 1206, 1210 CU C0G (NP0) Power amplifier High-Q Nickel barrier/ Tin 01005 AT X5R X7R Optical communications Au termination Nickel barrier/ Au 0201, 0402 ST X5R X7R X7S PCB with severe bending conditions Soft termination Nickel barrier/ Tin (Soft Termination) 0201, 0402 1206, 1210 CF C0G (NP0) X7R High voltage & Power circuits High voltage 250VDC, 630VDC 1000VDC, 2000VDC 3000VDC, 4000VDC Nickel barrier/ Tin 0805, 1206, 1210 1808, 1812, 2208 2220 Option Negative temperature coefficient dielectric types are available on request. Multilayer Ceramic Chip Capacitors Packaging Code Dimensions E 8 / 2 L W Taping Material Code E P T P PP Taping Width Material Plastic Paper Code 4 8 12 Width 4mm 8mm 12mm P Pitch Code 1 2 4 8 Pitch 1mm 2mm 4mm 8mm Dimensions and Packaging Quantities Size 02 Code JIS EIA Dimension Code L W 0402 01005 A 0.40.02 0.20.02 0.60.03 0.30.03 A 0603 0201 C D E F 0.60.05 0.30.05 0.60.09 0.30.09 0.60.10 0.30.10 1005 0.50.05 0.30.05 0.13 0.23 0.19 0.30.09 0.25 max. 0.30.10 0.13 0.23 0.19 0.15 0.35 0.30 0.33 max. 0.50.05 B 1.00.07 0.50.07 1.00.10 0.50.10 1.00.15 0.50.15 1.00.20 0.50.20 1.60.10 0.80.10 0603 0.50.10 1.60.15 0805 1206 32 3225 1210 42 4520 1808 43 4532 1812 52 5720 2208 55 5750 2220 F A B C D E F G H J K L M A B C D E F G H J K A B C D E F G A B A B C D E A A B C 0.50.15 0.33 max. 0.50.20 0.55 max. 0.80.10 0.55 max. 0.80.15 D E 0.50.07 0.35 max. C 3216 0.20 0402 K L A 316 0.20 0.35 max. J 2012 0.10 E H 21 0.13 0.25 max. 1.00.05 G 1608 0.14 D F 105 0.07 0.20.02 0.22 max. B 05 P to P min. 0.30.03 A C P max. 0.22 max. B 03 Dimensions (mm) T P min. 0.20 0.60 0.50 0.20 0.75 0.70 0.30 0.85 1.40 0.30 0.85 1.90 0.30 1.00 1.40 0.15 0.85 2.60 0.30 1.10 2.00 0.15 0.85 4.20 0.30 1.40 2.50 0.80.15 1.60.20 2.00.10 0.80.20 1.250.10 2.00.15 1.250.15 2.00.20 1.250.20 3.20.20 1.60.15 3.20.20 1.60.20 3.20.30 3.20.35 1.60.30 3.20.30 2.50.20 4.50.20 2.00.20 4.50.30 3.20.20 5.70.40 2.00.20 5.70.40 5.00.40 Note: Taping denotes the quantity packaged per reel (kp means 1000 pieces). 0.55 max. 0.80.20 0.55 max. 0.95 max. 1.00 max. 0.60.1 0.850.10 1.050.10 1.250.10 0.55 max. 0.95 max. 1.250.15 0.95 max. 1.250.20 0.95 max. 1.00 max. 1.150.10 1.250.10 1.60.15 0.95 max. 1.00 max. 1.60.20 1.60.30 1.00 max. 1.40 max. 1.60 max. 1.60.15 2.20 max. 2.00.2 2.50.2 1.6 max. 2.2 max. 2.0 max. 2.00.2 2.5 max. 2.50.2 2.80.2 2.2 max. 2.0 max. 2.5 max. 2.8 max. Please contact us. Maximum quantity per reel 180 Reel 330 Reel 40kp (E4/1) 20kp (P8/2) 30kp (P8/1) 150kp (P8/1) 15kp (P8/2) 50kp (P8/2) 30kp (P8/1) 150kp (P8/1) 15kp (P8/2) 50kp (P8/2) 30kp (P8/1) 150kp (P8/1) 15kp (P8/2) 50kp (P8/2) 15kp (P8/2) 15kp (P8/2) 15kp (P8/2) 20kp (P8/1) 100kp (P8/1) 10kp (P8/2) 50kp (P8/2) 20kp (P8/1) 100kp (P8/1) 10kp (P8/2) 50kp (P8/2) 20kp (P8/1) 100kp (P8/1) 10kp (P8/2) 50kp (P8/2) 20kp (P8/1) 100kp (P8/1) 10kp (P8/2) 50kp (P8/2) 20kp (P8/1) 100kp (P8/1) 10kp (P8/2) 50kp (P8/2) 20kp (P8/1) 50kp (P8/2) 10kp (P8/2) 20kp (P8/1) 100kp (P8/1) 10kp (P8/2) 50kp (P8/2) 20kp (P8/1) 50kp (P8/2) 10kp (P8/2) 20kp (P8/1) 10kp (P8/2) 10kp (P8/2) 10kp (P8/2) 4kp (P8/4) 8kp (P8/2) 4kp (P8/4) 8kp (P8/2) 4kp (P8/4) 8kp (P8/2) 4kp (P8/4) 8kp (P8/2) 4kp (P8/4) 4kp (P8/4) 4kp (P8/4) 4kp (E8/4) 4kp (P8/4) 4kp (P8/4) 3kp (E8/4) 3kp (E8/4) 4kp (P8/4) 4kp (P8/4) 3kp (E8/4) 4kp (P8/4) 3kp (E8/4) 4kp (P8/4) 4kp (E8/4) 3kp (E8/4) 3kp (E8/4) 2.5kp (E8/4) 4kp (P8/4) 4kp (E8/4) 2.5kp (E8/4) 2kp (E8/4) 2kp (E8/4) 4kp (E8/4) 3kp (E8/4) 2.5kp (E8/4) 2.5kp (E8/4) 2kp (E8/4) 2kp (E8/4) 1kp (E8/4) 2kp (E12/4) 2kp (E12/4) 1kp (E12/8) 1kp (E12/8) 0.5kp (E12/8) 0.5kp (E12/8) 0.5kp (E12/8) 2kp (E12/4) 1kp (E12/8) 0.5kp (E12/8) 0.5kp (E12/8) 50kp (P8/2) 10kp (P8/4) 20kp (P8/2) 10kp (P8/4) 20kp (P8/2) 10kp (P8/4) 20kp (P8/2) 10kp (P8/4) 20kp (P8/2) 10kp (P8/4) 10kp (P8/4) 10kp (P8/4) 10kp (E8/4) 10kp (P8/4) 10kp (P8/4) 10kp (E8/4) 10kp (E8/4) 10kp (P8/4) 10kp (P8/4) 10kp (E8/4) 10kp (P8/4) 10kp (E8/4) 10kp (P8/4) 10kp (E8/4) 10kp (E8/4) 10kp (E8/4) 5kp (E8/4) 10kp (P8/4) 10kp (E8/4) 5kp (E8/4) 10kp (E8/4) 10kp (E8/4) 5kp (E8/4) 5kp (E8/4) 5kp (E8/4) 5kp (E8/4) 4kp (E8/4) - Multilayer Ceramic Chip Capacitors Ordering Information KYOCERA PART NUMBER CM 03 X5R 225 M 06 SERIES CODE = = = CM CT CU General Purpose Low Profile High-Q AT ST CF = = = Au termination Soft termination High Voltage SIZE CODE SIZE 02 = 03 = 05 = 105 = 21 = 316 = EIA (JIS) 01005 (0402) 0201 (0603) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216) SIZE 32 = 42 = 43 = 52 = 55 = EIA (JIS) 1210 (3225) 1808 (4520) 1812 (4532) 2208 (5720) 2220 (5750) DIELECTRIC CODE CODE EIA CODE CG = C0G (NPO) X7S = X7S (Option) X5R = X5R X6S = X6S (Option) X7R = X7R Negative temperature coefficient dielectric types are available on request. CAPACITANCE CODE Capacitance expressed in pF. Two significant digits plus number of zeros. For Values < 10pF, Letter R denotes decimal point, = 1R5 eg. 100000pF = 104 1.5pF = 104 = R50 0.1F 0.5pF = 107 4700pF = 472 100F TOLERANCE CODE A = 0.05pF (option) B = 0.1pF C = 0.25pF D = 0.5pF G = 2% (option) J = 5% K = 10% M = 20% VOLTAGE CODE 04 06 10 16 25 35 50 = = = = = = = 4VDC 6.3VDC 10VDC 16VDC 25VDC 35VDC 50VDC 100 = 100VDC 250 = 250VDC 630 = 630VDC 1000 2000 3000 4000 = = = = 1000VDC 2000VDC 3000VDC 4000VDC TERMINATION CODE A = Nickel Barrier/ Tin G = Nickel Barrier/ Au K = Nickel Barrier/ Au Y = Nickel Barrier/ Cu S = Nickel Barrier/ Tin (Soft Termination) G : AuSn solder and conductive adhesive. K : Wire bonding and conductive adhesive. PACKAGING CODE B C T Q L = Bulk = Bulk Cassette (option) = 7" Reel Taping & 4mm or 8mm1 Cavity pitch = 7" Reel Taping & 1mm Cavity pitch = 13" Reel Taping & 4mm Cavity pitch H = 7" Reel Taping & 2mm Cavity pitch N = 13" Reel Taping & 2mm Cavity pitch W = 13" Reel Taping & 1mm Cavity pitch P = 7" Reel Taping & 1mm Cavity pitch Carrier tape width 4mm. 1 OPTION Thickness max. value is indicated in CT series EX. 125 1.25mm max. 095 0.95mm max. Applied for size 43 to 55. A H Multilayer Ceramic Chip Capacitors Temperature Characteristics and Tolerance Temperature Compensation Type ppm/ C 30 0 60 Code CG CH Temperature Range -55 to 125C Note: All parts of C0G will be marked as "CG" but will conform to the above table. Temperature coefficients are determined by calculation based on measurement at 20C and 85C. High Dielectric Constant Type EIA Dielectric Temperature Range X5R -55 to 85C X7R -55 to 125C X7S X6S -55 to 125C -55 to 105C C max. 15% 22% option Available Tolerances E Standard Number Dielectric materials, capacitance values and tolerances are available in the following combinations only: EIA Dielectric Tolerance 3 A=0.05pF Capacitance B=0.1pF 5pF C=0.25pF C0G D=0.50pF 3 G=2% J=5% K=10% 3 X6S X7S X5R X7R 2 K=10% M=20% E3 E12 E24 (Option) 1.0 1.0 1.1 1.2 1.2 1.3 1.5 1.5 1.6 1.8 1.8 2.0 2.2 2.2 2.4 2.7 2.7 3.0 3.3 3.3 3.6 3.9 3.9 4.3 4.7 4.7 5.1 5.6 5.6 6.2 6.8 6.8 7.5 8.2 8.2 9.1 1.0 <0.5pF 1.0 1.5 1 <10pF 2.2 10pF E12 Series E6 2.2 3.3 4 E3 Series Note: 1 Nominal values below 10pF are available in the standard values of 0.5pF, 1.0pF, 1.5pF, 2.0pF, 3.0pF, 4.0pF, 5.0pF, 6.0pF, 7.0pF, 8.0pF, 9.0pF 2 J = 5% for X7R (X5R) is available on request. 3 option 4 E6 series is available on request. 4.7 4.7 6.8 CM Series General [RoHS Compliant Products] Features Applications We offer a diverse product line ranging from ultra-compact (0.4x0.2mm) to large (4.5x3.2mm) components configured for a variety of temperature characteristics, rated voltages, and packages. We offer the choice and flexibility for almost any applications. This standard type is ideal for use in a wide range of applications, from commercial to industrial equipment. Temperature Compensation Dielectric Size (EIA Code) CM02 (01005) C1 Temperature Rated Voltage (VDC) Capacitance (pF) R20 R50 1R0 1R5 100 120 101 121 102 122 103 123 0.2 0.5 1.0 1.5 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 16 CM03 (0201) C1 25 25 50 CM105 (0603) C1 50 50 CM21 (0805) C1 16 25 50 A B A B E B E E G G E12 Series Please contact for capacitance value other than standard. 1: CG,CH Alphabets in capacitance chart denote dimensions. Please refer to the below table for detail. (Example) In case of "B" for CM03; L : 0.60.03mm W : 0.30.03mm T : 0.30.03mm CM05 (0402) C1 Dimension (mm) Size Size Code L W T 02 A 0.40.02 0.20.02 0.20.02 03 B 0.60.03 0.30.03 0.30.03 05 E 1.00.05 0.50.05 0.50.05 105 B 1.60.10 0.80.10 0.80.10 E 2.00.10 1.250.10 0.850.10 G 2.00.10 1.250.10 1.250.10 21 CM Series General [RoHS Compliant Products] X5R Dielectric Size (EIA Code) Rated Voltage (VDC) Capacitance (pF) 101 151 102 152 103 153 104 105 106 107 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 10000 15000 22000 33000 47000 68000 100000 220000 470000 1000000 2200000 4700000 10000000 22000000 47000000 100000000 CM02 (01005) 6.3 10 16 A8 A8 105 106 107 220000 470000 1000000 2200000 4700000 10000000 22000000 47000000 100000000 6.3 10 CM05 (0402) 16 25 4 6.3 10 CM105 (0603) 16 25 E3 E3 35 4 6.3 10 16 CM21 (0805) 25 50 4 6.3 10 16 25 50 B3 B3 B4 A8 B7 B7 B1 B3 E5 A8 B8 D10 D9 C8 D8 E8 E7 D10 H8 J10 E8 E8 E8 B3 H7 B4 B8 D8 H7 B5 E8 L8 J8 D5 D8 G1 G3 D8 G8 G3 B8 G4 G5 M5 M8 K8 M8 M8 M7 Size (EIA Code) Rated Voltage (VDC) Capacitance (pF) CM03 (0201) CM316 (1206) 6.3 10 16 25 CM32 (1210) 50 E5 H5 E4 H8 4 6.3 10 16 H3 E3 E3 100 H3 H8 H8 G5 F4 G4 C3 G3 CM43 (1812) 25 50 B3 F1 6.3 50 CM21 size and smaller : E6 Series CM316 size and larger / capacitance value of 0.1F and larger : E3 Series Please contact for capacitance value other than standard. Optional Spec. D1 F3 G3 G3 G8 G5 E5 Two digits alphanumerics in capacitance chart denote dimensions and tan . Please refer to the below table for detail. (Example) In case of "B3" for CM03; L : 0.60.03mm W : 0.30.03mm T : 0.30.03mm Tan : 5.0% max. Dimension (mm) Size Size Code L W T 02 A 0.40.02 0.20.02 0.20.02 B 0.60.03 0.30.03 0.30.03 03 C 0.60.05 0.30.05 0.30.05 D 0.60.09 0.30.09 0.30.09 E 1.00.05 0.50.05 0.50.05 H 1.00.10 0.50.10 0.50.10 J 1.00.15 0.50.15 0.50.15 L 1.00.20 0.50.20 0.50.20 05 105 21 B 1.60.10 0.80.10 0.80.10 D 1.60.15 0.80.15 0.80.15 G 2.00.10 1.250.10 1.250.10 K 2.00.15 1.250.15 1.250.15 M 2.00.20 1.250.20 1.250.20 Size 316 32 43 Dimension (mm) Size Code L W T Tan Code Tan E 3.20.20 1.60.15 1.60.15 1 2.5% max. H 3.20.20 1.60.20 1.60.20 3 5.0% max. B 3.20.30 2.50.20 1.40 max. 4 7.0% max. C 3.20.30 2.50.20 1.60 max. 5 7.5% max. F 3.20.30 2.50.20 2.00.2 7 10.0% max. G 3.20.30 2.50.20 2.50.2 8 12.5% max. D 4.50.30 3.20.20 2.50.2 9 15.0% max. E 4.50.30 3.20.20 2.80.2 10 20.0% max. CM Series General [RoHS Compliant Products] X7R Dielectric Size CM02 (EIA Code) (01005) Rated Voltage (VDC) Capacitance (pF) 101 151 102 152 103 153 104 105 106 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 10000 15000 22000 33000 47000 68000 100000 220000 470000 1000000 2200000 4700000 10000000 22000000 16 CM03 (0201) 10 16 104 105 106 47000 100000 220000 470000 1000000 2200000 4700000 10000000 22000000 25 16 CM105 (0603) 25 6.3 10 CM21 (0805) 16 25 50 6.3 10 16 25 B3 E3 E2 E8 B1 E8 B2 B2 B8 D8 G1 B3 G2 B8 G2 D8 G3 G8 M8 M8 M8 CM316 (1206) 6.3 10 16 CM32 (1210) 25 50 100 10 16 G8 M8 M8 CM43 (1812) 25 50 100 B1 F1 G1 50 100 B1 D1 D1 C1 E1 C2 B2 F2 E2 E3 H8 H8 H8 G2 H3 H3 G8 G8 G8 H5 H8 Optional Spec. G3 CM21 size and smaller : E6 Series CM316 size and larger / capacitance value of 0.1F and larger : E3 Series Please contact for capacitance value other than standard. Two digits alphanumerics in capacitance chart denote dimensions and tan . Please refer to the below table for detail. (Example) In case of "B3" for CM03; L : 0.60.03mm W : 0.30.03mm T : 0.30.03mm Tan : 5.0% max. Dimension (mm) Size Size Code L W T 02 A 0.40.02 0.20.02 0.20.02 03 B 0.60.03 0.30.03 0.30.03 05 105 21 Size 2.5% max. 3.20.20 1.60.15 1.60.15 2 3.5% max. E 316 0.50.05 0.50.05 H 3.20.20 1.60.20 1.60.20 3 5.0% max. 0.80.10 0.80.10 B 3.20.30 2.50.20 1.40 max. 5 7.5% max. 0.80.15 0.80.15 8 12.5% max. D 1.60.15 G 2.00.10 1.250.10 1.250.10 M 2.00.20 1.250.20 1.250.20 Rated Voltage (VDC) Capacitance (pF) 100 316 H J 32 43 Dimension (mm) L W T 3.20.20 1.60.20 1.60.20 3.20.30 1.60.30 1.60.30 Tan Tan Code 3 5.0% max. Two digits alphanumerics in capacitance chart denote dimensions and tan . Please refer to the below table for detail. Optional Spec. 1 3.20.20 1.60.10 Size Code 106 1.60.15 1.150.10 C T 1.00.05 Size H3 J3 Tan W E CM316 (1206) 105 Tan Code L B Size (EIA Code) 47000 100000 220000 470000 1000000 2200000 4700000 10000000 22000000 Dimension (mm) Size Code X7S Dielectric 104 50 B2 B2 A8 Size (EIA Code) Rated Voltage (VDC) Capacitance (pF) CM05 (0402) F 3.20.30 2.50.20 2.00.2 G 3.20.30 2.50.20 2.50.2 B 4.50.30 3.20.20 2.00.2 D 4.50.30 3.20.20 2.50.2 M3 Multilayer Ceramic Chip Capacitors Test Conditions and Standards Test Conditions and Specifications for Temperature Compensation Type (C Characteristics) CM/ CU/ CF Series Test Items Capacitance Value (C) Test Conditions Capacitance Frequency C1000pF C>1000pF Q Specifications Volt 1MHz10% 0.5 to 5Vrms 1kHz10% Within tolerance C30pF : Q1000 C<30pF : Q400+20C Insulation Resistance (IR) Measured after the rated voltage is applied for 1 minute at room ambient. For the rated voltage of over 630V, apply 500V for 1 minute at room ambient. The charge and discharge current of the capacitor must not exceed 50mA. Over 10000M or 500M * F, whichever is less Dielectric Resistance Apply 3 times of the rated voltage for 1 to 5 seconds. Apply 1.5 times when the rated voltage is 250V or over. Apply 1.2 times when the rated voltage is 630V or over. The charge and discharge current of the capacitor must not exceed 50mA. No problem observed Appearance Microscope No problem observed Termination Strength Apply a sideward force of 500g (5N) to a PCBmounted sample. Apply 2N for 0201, and 1N for 01005 size. No problem observed Bending Strength Glass epoxy PCB: Fulcrum spacing: 90mm, duration time 10 seconds. No significant damage at 1mm bent Vibration Test Appearance C Q Soldering Heat Resistance Appearance C Q IR Vibration frequency: 10 to 55 (Hz) Amplitude: 1.5mm Sweeping condition: 105510Hz/ 1 minute in X, Y and Z Directions: 2 hours each, 6 hours total. No problem observed Soak the sample in 260C5C solder for 100.5 seconds and place in room ambient, and measure after 242 hours. (Pre-heating conditions) No problem observed Order 1 2 Temperature 80 to 100C 150 to 200C Time 2 minutes 2 minutes Withstanding The charge and discharge current of the capacitor must not exceed 50mA for IR and withstanding Voltage Within Tolerance C30pF : Q1000 C<30pF : Q400+20C Within 2.5% or 0.25pF, whichever is larger C30pF : Q1000 C<30pF : Q400+20C Over 10000M or 500M * F whichever is less Resist without problem voltage measurement. Soaking condition Sn-3Ag-0.5Cu Sn63 Solder Solderablity Temperature Cycle Appearance C Q IR 2455C 2355C 30.5 sec. 20.5 sec. (Cycle) Room temperature (3min.) Lowest operation temperature (30min.) Room temperature (3min.) Highest operation temperature(30min.) Solder coverage : 90% min. No problem observed Within 2.5% or 0.25pF, whichever is larger C30pF : Q1000 C<30pF : Q400+20C Over 10000M or 500M * F, whichever is less After 5 cycles, measure after 242 hours. Withstanding The charge and discharge current of the capacitor Voltage Resist without problem must not exceed 50mA for IR and withstanding voltage measurement. Load Humidity Test (Except CF Series) Appearance C Q IR HighAppearance Temperature C with Loading Q IR After applying rated voltage for 500+12/ -0 hours in pre-condition at 40C2C, humidity 90 to 95%RH, allow parts to stabilize for 242 hours, at room temperature before measurement. The charge and discharge current of the capacitor must not exceed 50mA for IR measurement. No problem observed After applying twice the rated voltage at the temperature of 1253C for 1000+12/ -0 hours, measure the sample after 242 hours. Apply 1.5 times when the rated voltage is 250V or over. Apply 1.2 times when the rated voltage is 630V or over. The charge and discharge current of the capacitor must not exceed 50mA for IR measurement. No problem observed. Please ask for individual specification for the hatched range in previous chart. Within 7.5% or 0.75pF, whichever is larger C30pF : Q200 C<30pF : Q100+10C/ 3 Over 500M or 25M * F, whichever is less Within 3% or 0.3pF, whichever is larger C30pF : Q350 10pF10F Insulation Resistance (IR) Dielectric Resistance Appearance Termination Strength Bending Strength Vibration Test Appearance C Tan (%) Soldering Heat Resistance Appearance C Tan (%) IR Withstanding Voltage Specifications Measure after heat treatment Within tolerance Volt 1kHz10% 1.00.2Vrms 120Hz10% 0.50.2Vrms Measured after the rated voltage is applied for 1 minute at room ambient. The charge and discharge current of the capacitor must not exceed 50mA. Apply 2.5 times of the rated voltage for 1 to 5 seconds. The charge and discharge current of the capacitor must not exceed 50mA. Microscope Apply a sideward force of 500g (5N) to a PCB-mounted sample. note : 2N for 0201 size in for 01005 size. Exclude CT series with thickness of less than 0.66mm. Glass epoxy PCB: Fulcrum spacing: 90mm, duration time 10 seconds. Exclude CT series with thickness of less than 0.66mm. Take the initial value after heat treatment. Vibration frequency: 10 to 55 (Hz) Amplitude: 1.5mm Sweeping condition: 105510Hz/ 1 minute in X, Y and Z Directions: 2 hours each, 6 hours total. Take the initial value after heat treatment. Soak the sample in 260C5C solder for 100.5 seconds and place in room ambient, and measure after 242 hours. (Pre-heating conditions) Order 1 2 Temperature 80 to 100C 150 to 200C Time 2 minutes 2 minutes Refer to capacitance chart Over 10000M or 500M * F, whichever is less No problem observed No problem observed No problem observed No significant damage at 1mm bent No problem observed Within tolerance Within tolerance No problem observed Within 7.5% Within tolerance Over 10000M or 500M * F, whichever is less Resist without problem The charge and discharge current of the capacitor must not exceed 50mA for IR and withstanding voltage measurement. Soaking condition Solderablity Temperature Cycle Sn-3Ag-0.5Cu Sn63 Solder Appearance C Tan (%) IR Withstanding Voltage Load Humidity Test Appearance C Tan (%) IR HighTemperature with Loading Appearance C Tan (%) IR Pre-treatment Heat Voltage 2455C 2355C 30.5 sec. 20.5 sec. Take the initial value after heat treatment. (Cycle) Room temperature (3min.) Lowest operation temperature (30min.) Room temperature (3min.) Highest operation temperature(30min.) After 5 cycles, measure after 242 hours. The charge and discharge current of the capacitor must not exceed 50mA for IR and withstanding voltage measurement. Take the initial value after voltage treatment. After applying rated voltage for 500+12/ -0 hours in pre-condition at 40C2C, humidity 90 to 95%RH, allow parts to stabilize for 242 hours, at room temperature before measurement. The charge and discharge current of the capacitor must not exceed 50mA for IR measurement. Take the initial value after voltage treatment. After applying twice the rated voltage at the highest operation temperature for 1000+12/ -0 hours, measure the sample after 242 hours. The charge and discharge current of the capacitor must not exceed 50mA for IR measurement. Apply 1.5 times when the rated voltage is 10V or less. Applied voltages for respective products are indicated in the below chart. Solder coverage : 90% min. No problem observed Within 7.5% Within tolerance Over 10000M or 500M * F, whichever is less Resist without problem No problem observed Within 12.5% 200% max. of initial value Over 500M or 25M * F, whichever is less No problem observed Within 12.5% 200% max. of initial value Over 1000M or 50M * F, whichever is less Keep specimen at 150+0/ -10C for 1 hour, leave specimen at room ambient for 242 hours. Apply the same test condition for 1 hour, then leave the specimen at room ambient for 242 hours. High-temperature with Loading Applied Voltage (Rated Voltage x ) Applied Voltage Rated Voltage Products 4V CT03X5R104 x1.3 CM105X5R475, CM316X5R476, CM02X5R153-104 6.3V CT05X5R104, CT21X5R106, CT03X5R104 CM02X7R101-222, CM05X7R333-104, CM105X7R474-105, CM21X7R105-475, CM316X7R475-106, CM32X7R106-226, CM05X5R224, CM105X5R225, CM21X5R475-106, CM316X5R226 16V CT105X5R105, CT21X5R225-475, CT316X5R106, CM03X5R332-103, CM02X5R101-103 CM105X7R474, CM21X7R105-225, CM316X7R475, CM32X7R106, CM105X5R474-105, CM21X5R225-106, CM316X5R106, CM32X5R106-226 25V x1.5 CT316X5R225-106, CM03X5R152-103, CM05X7R103-104 CM21X5R105, CM32X5R106, CM32X7R106 50V CT21X5R225, CT316X5R105-475 100V CM32X7RK74, CM43X7R105 Please ask for individual specification for the hatched range in previous chart. Multilayer Ceramic Chip Capacitors Test Conditions and Standards Substrate for Electrical Tests (Unit: mm) c a b Substrate for Bending Test (Unit: mm) Size (EIA Code) a b c 02 (01005) 0.15 0.50 0.20 03 (0201) 0.26 0.92 0.32 05 (0402) 0.4 1.4 0.5 105 (0603) 1.0 3.0 1.2 21 (0805) 1.2 4.0 1.65 316 (1206) 2.2 5.0 2.0 32 (1210) 2.2 5.0 2.9 42 (1808) 3.5 7.0 3.7 43 (1812) 3.5 7.0 3.7 52 (2208) 4.5 8.0 5.6 55 (2220) 4.5 8.0 5.6 Substrate for Adhesion Strength Test a 10.1 c 40 a b 100 R5 Soldering Pressure Load 90mm 1.6 Testing Board Support 5mm Testing Table Testing Board : Glass Epoxy Board (CE4 or FR4) Testing Board Thickness: 1.60.2mm Circuit Thickness : 0.040.01mm 02, 03, 05 size 0.80.1mm c b Multilayer Ceramic Chip Capacitors Packaging Options Tape and Reel Reel * Reel Code Reel 7-inch Reel (CODE: T, H, Q) 7-inch Reel (CODE: P) 13-inch Reel (CODE: L, N, W) Code Reel 7-inch Reel (CODE: T, H, Q) 7-inch Reel (CODE: P) 13-inch Reel (CODE: L, N, W) W2 E C B D R A W1 F=1mm (02 Type) Feed Hole J Punched rectangular hole to hold (Unit: mm) A B C D 60 min. 130.5 210.8 W1 W2 R 10.51.5 16.5 max. 4.350.3 6.951.0 9.51.0 16.5 max. 180 +0 -2.0 1782.0 3302.0 E 2.00.5 1.0 Carrier tape width 8mm. For size 42 (1808) or over, Tape width 12mm and W1: 141.5, W2: 18.4mm max. (Plastic) E Carrier Tape D A C B F F=1mm (02, 03, 05 Type) J (Paper) Parts insertion cavity E D A C B F F 02 Type: 0.4 max. 03 Type: 0.5 max. 05 Type: 0.75 max. H F=2mm (02, 03, 05, 105 Type) Feed Hole Size (EIA Code) A B F 02 (01005) 0.230.02 0.250.03 0.430.02 0.450.03 03 (0201) 0.370.03 0.670.03 05 (0402) 0.650.1 1.150.1 105 (0603) 21 (0805) 316 (1206) 32 (1210) 42 (1808) 43 (1812) 52 (2208) 55 (2220) 1.00.2 1.50.2 2.00.2 2.90.2 2.40.2 3.60.2 2.40.2 5.30.2 1.80.2 2.30.2 3.60.2 3.60.2 4.90.2 4.90.2 6.00.2 6.00.2 1.00.02 2.00.05 1.00.05 2.00.05 1.00.05 2.00.05 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 8.00.1 4.00.1 8.00.1 0.5 max. H Feed Hole (Unit: mm) Punched rectangular hole to hold capacitor J (Paper) E A Option D C B (Unit: mm) F H F 02 Type: 0.4 max. 03 Type: 0.6 max. 05 Type: 0.75 max. 105 Type: 1.1 max. F=4mm (105, 21, 316, 32, 42, 52 Type) Feed Hole Punched rectangular hole to hold capacitor J A (Plastic) (Paper) 2.8 max. E D C B F H G Holes only for plastic carrier tape. 0.3 min. 0.6 max. F=8mm (43, 55 Type) Feed Hole J F Carrier Tape C D 1.0 4mm 4.0 1.8 0.02 +0.08 0.02 Plastic 1.0 8.0 0.05 +0.3/ -0.1 8mm 2.0 Paper 3.5 0.05 0.05 8.0 0.3 4.0 8mm 0.1 Plastic Punched rectangular hole to hold capacitor (Plastic) 3.0 max. E A D B C F H G Holes only for plastic carrier tape. 0.3 min. 0.6 max. 1.1 max. 8.0 0.1 12mm Plastic 12.0 0.3 5.5 0.05 E 0.9 0.05 G 1.75 0.1 2.0 0.05 - H 2.0 0.04 4.0 0.05 J 0.8 0.04 1.5 4.0 +0.1/ -0 0.1 Multilayer Ceramic Chip Capacitors Packaging Options Detail of leader and trailer Empty Pockets Leader Components End Start 160mm min. 100mm min. 400mm min. Adhesive tape 1) The exfoliative strength when peeling off the top tape from the carrier tape by the method of the following figure shall be 0.1 to 0.7N. 02 Size: 0.1 to 0.5N 2) When the top tape is peeled off, the adhesive stays on the top tape. 3) Chip capacitors will be in a state free without being stuck on the thermal adhesive tape. Exfoliating angle: 165 to 180 degrees to the carrier tape. Exfoliating speed: 300 mm/min. Peeling Direction Top Tape 165 to 180 Carrier Tape Unrolling Direction Bulk Case (Unit: mm) 12 36 Slider Shutter 110 Connection Area * Please contact Kyocera for details. Multilayer Ceramic Chip Capacitors Surface Mounting Information Dimensions for recommended typical land Since the amount of solder (size of fillet) to be used has direct influence on the capacitor after mounting, the sufficient consideration is necessary. When the amounts of solder is too much, the stress that a capacitor receives becomes larger. It may become the cause of a crack in the capacitor. When the land design of printed wiring board is considered, it is necessary to set up the form and size of land pattern so that the amount of solder is suitable. (General, High-Voltage) Land Pattern General, High-Voltage (Unit: mm) Size (EIA Code) LxW a 02 (01005) 0.4x0.2 0.13 to 0.20 0.12 to 0.18 0.20 to 0.23 03 (0201) 0.6x0.3 0.20 to 0.30 0.25 to 0.35 0.30 to 0.40 05 (0402) 1.0x0.5 0.30 to 0.50 0.35 to 0.45 0.40 to 0.60 105 (0603) 1.6x0.8 0.70 to 1.00 0.80 to 1.00 0.60 to 0.80 21 (0805) 2.0x1.25 1.00 to 1.30 1.00 to 1.20 0.80 to 1.10 316 (1206) 3.2x1.6 2.10 to 2.50 1.10 to 1.30 1.00 to 1.30 32 (1210) 3.2x2.5 2.10 to 2.50 1.10 to 1.30 1.90 to 2.30 42 (1808) 4.5x2.0 2.50 to 3.201 1.80 to 2.30 1.50 to 1.80 43 (1812) 4.5x3.2 2.50 to 3.201 1.80 to 2.30 2.60 to 3.00 52 (2208) 5.7x2.0 4.20 to 4.70 2.00 to 2.50 1.50 to 1.80 55 (2220) 5.7x5.0 4.20 to 4.70 2.00 to 2.50 4.20 to 4.70 b c Sample capacitor c b a Soldering resist 1 Dimension of 3.0 to 3.5mm is recommended for "a", in the case of High-Voltage products. Design of printed circuit and Soldering Ideal Solder Height The recommended fillet height shall be 1/2 of the thickness of capacitors or 0.5mm. When mounting two or more capacitors in the common land, it is necessary to separate the land with the solder resist strike so that it may become the exclusive land of each capacitor. Chip Capacitor T/ 2 or 0.5mm T Solder PCB Item Not recommended example Recommended example/ Separated by solder Solder resist Multiple parts mount Solder resist Mount with leaded parts Leaded parts Leaded parts Soldering iron Solder resist Wire soldering after mounting Wire Solder resist Overview Solder resist Multilayer Ceramic Chip Capacitors Surface Mounting Information Mounting Design The chip could crack if the PCB warps during processing after the chip has been soldered. Recommended chip position on PCB to minimize stress from PCB warpage (Not recommended) (Ideal) Actual Mounting 1) If the position of the vacuum nozzle is too low, a large force may be applied to the chip capacitor during mounting, resulting in cracking. 2) During mounting, set the nozzle pressure to a static load of 1 to 3 N. 3) To minimize the shock of the vaccum nozzle, provide a support pin on the back of the PCB to minimize PCB flexture. (Ideal) (Not recommended) Crack Support pin 4) Bottom position of pick up nozzle should be adjusted to the top surface of a substrate which camber is corrected. 5) To reduce the possibility of chipping and cracks, minimize vibration to chips stored in a bulk case. 6) The discharge pressure must be adjusted to the part size. Verify the pressure during setup to avoid fracturing or cracking the chips capacitors. Resin Mold 1) If a large amount of resin is used for molding the chip, cracks may occur due to contraction stress during curing. To avoid such cracks, use a low shrinkage resin. 2) The insulation resistance of the chip will degrade due to moisture absorption. Use a low moisture absorption resin. 3) Check carefully that the resin does not generate a decomposition gas or reaction gas during the curing process or during normal storage. Such gases may crack the chip capacitor or damage the device itself. Multilayer Ceramic Chip Capacitors Surface Mounting Information Soldering Method 1) Ceramic is easily damaged by rapid heating or cooling. If some heat shock is unavoidable, preheat enough to limit the temperature difference (Delta T) to within 150 degree Celsius. 2) The product size 1.6x0.8mm to 3.2x1.6mm can be used in reflow and wave soldering, and the product size of bigger than 3.2x1.6mm, or smaller than 1.6x0.8mm can be used in reflow. Circuit shortage and smoking can be created by using capacitors which are used neglecting the above caution. 3) Please see our recommended soldering conditions. 4) In case of using Sn-Zn Solder, please contact us in advance. 5) The following condition is recommended for spot heater application. * Recommended spot heater condition Item Condition Distance 5mm min. Angle 45 How to point spot heater Projection Temp. 400C max. Flow rate Set at the minimum Nozzle diameter 2 to 4 (Single hole type) Application time 10 sec. max. (1206 and smaller) 30 sec.max. (1210 and larger) Single hole nozzle Angle 45 Recommended Temperature Profile (Sn-3Ag-0.5Cu) Reflow Recommended Temperature Profile (62Sn Solder) Reflow Peak temperature 230C5C 15 seconds maximum 250C5C 5 to 10 sec. max. 300 300 Preheat 200 1 to 3C/ sec. 170 to 180C 150 100 Temperature Temperature Cool at normal room temperature 220C max. 90 sec. max. 200 T 100 50 0 0 More than180C, 40 seconds maximum 60 seconds 60 seconds 9030 sec. Wave Minimize soldering time. Ensure that the temperature difference (T) does not exceed 150C. Ensure that the temperature difference (T) does not exceed 130C for 3.2x2.5mm size or larger. MLCC can withstand the above reflow conditions up to 3 times. Wave Preheat 300 Peak Temperature 245C to 260C 250 T 200 150 100 Cool at normal room temperature 50 Preheat Peak Temperature 230C to 260C 250 Temperature (C) 300 Temperature (C) Cool at normal room temperature after removing from furnace. 150 50 Minimize soldering time. Ensure that allowable temperature difference does not exceed 150C. Ensure that allowable temperature difference does not exceed 130C for 3.2x2.5mm size or larger. T 200 150 100 Cool at normal room temperature 50 0 0 60 to 120 sec. Preheat 250 250 60 to 120 sec. 5 sec. max. Ensure that the chip capacitor is preheated adequately. Ensure that the temperature difference (T) does not exceed 150C. Cool naturally after soldering. Wave soldering is not applicable for chips with size of 3.2x2.5mm or larger of 1.0x0.5mm or smaller and capacitor arrays. 5 sec. max. Ensure that the chip capacitor is preheated adequately. Ensure that the temperature difference (T) does not exceed 150C. Cool naturally after soldering. Wave soldering is not applicable for chips with size of 3.2x2.5mm or larger of 1.0x0.5mm or smaller and capacitor arrays. Soldering iron 1) Temperature of iron chip 2) Wattage 3) Tip shape of soldering iron 4) Soldering Time 1206 and smaller 350C max. 5) Cautions 1210 and larger 280C max. a) Pre-heating is necessary rapid heating must be avoided. 80W max. Delta T150C (product size of bigger than 3.2x1.6mm. Delta T130C) 3.0mm max. b) Avoid direct touching to capacitors. 3 sec. max. c) Avoid rapid cooling after soldering. Natural cooling is recommended. Consult as if it is difficult to keep the temperature 280C max. for 1210 and larger MLCC'S. Multilayer Ceramic Chip Capacitors Precautions Circuit Design 1. Once application and assembly environments have been checked, the capacitor may be used in conformance with the rating and performance which are provided in both the catalog and the specifications. Use exceeding that which is specified may result in inferior performance or cause a short, open, smoking, or flaming to occur, etc. 2. Please consult the manufacturer in advance when the capacitor is used in devices such as: devices which deal with human life, i.e. medical devices; devices which are highly public orientated; and devices which demand a high standard of liability. Accident or malfunction of devices such as medical devices, space equipment and devices having to do with atomic power could generate grave consequence with respect to human lives or, possibly, a portion of the public. Capacitors used in these devices may require high reliability design different from that of general purpose capacitors. 3. Please use the capacitors in conformance with the operating temperature provided in both the catalog and the specifications. Be especially cautious not to exceed the maximum temperature. In the situation the maximum temperature set forth in both the catalog and specifications is exceeded, the capacitor's insulation resistance may deteriorate, power may suddenly surge and short-circuit may occur. The capacitor has a loss, and may self-heat due to equivalent series resistance when alternating electric current is passed therethrough. As this effect becomes especially pronounced in high frequency circuits, please exercise caution. When using the capacitor in a (self-heating) circuit, please make sure the surface of the capacitor remains under the maximum temperature for usage. Also, please make certain temperature rises remain below 20C. 4. Please keep voltage under the rated voltage which is applied to the capacitor. Also, please make certain the peak voltage remains below the rated voltage when AC voltage is super-imposed to the DC voltage. In the situation where AC or pulse voltage is employed, ensure average peak voltage does not exceed the rated voltage. Exceeding the rated voltage provided in both catalog and specifications may lead to defective withstanding voltage or, in worst case situations, may cause the capacitor to smoke or flame. 5. When the capacitor is to be employed in a circuit in which there is continuous application of a high frequency voltage or a steep pulse voltage, even though it is within the rated voltage, please inquire to the manufacturer. In the situation the capacitor is to be employed using a high frequency AC voltage or a extremely fast rising pulse voltage, even though it is within the rated voltage, it is possible capacitor reliability will deteriorate. 6. It is a common phenomenon of high-dielectric products to have a deteriorated amount of static electricity due to the application of DC voltage. Due caution is necessary as the degree of deterioration varies depending on the quality of capacitor materials, capacity, as well as the load voltage at the time of operation. 7. Do not use the capacitor in an environment where it might easily exceed the respective provisions concerning shock and vibration specified in the catalog and specifications. In addition, it is a common piezo phenomenon of high dielectric products to have some voltage due to vibration or to have noise due to voltage change. Please contact sales in such case. 8. If the electrostatic capacity value of the delivered capacitor is within the specified tolerance, please consider this when designing the respective product in order that the assembled product function appropriately. 9. Please contact us upon using conductive adhesives. Storage 1. If the component is stored in minimal packaging (a heat-sealed or zippered plastic bag), the bag should be kept closed. Once the bag has been opened, reseal it or store it in a desiccator. 2. Keep storage place temperature +5 to +40 degree C, humidity 20 to 70% RH. See JIS C 60721-3-1, class 1K2 for other climatic conditions. 3. The storage atmosphere must be free of corrosive gas such as sulfur dioxide and chlorine. Also, avoid exposing the product to saline moisture. If the product is exposed to such atmospheres, the terminals will oxidize and solderability will be effected. 4. Precautions 1) to 3) apply to chip capacitors packaged in carrier tapes and bulk cases. 5. The solderability is assured for 6 months from our shipping date if the above storage precautions are followed. 6. Chip capacitors may crack if exposed to hydrogen (H2) gas while sealed or if coated with silicon, which generates hydrogen gas. Safety application guideline and detailed information of electrical properties are also provided in Kyocera home page; URL: http://www.kyocera.co.jp/electronic/