06/2003
ADA10000
Linear Amplifier MMIC
Data Sheet - Rev 2.3
S3 Package
Modified 16 Pin SOIC
Figure 1: Block Diagram
FEATURES
• High Linearity : +15 dBm IIP3 (+8 V supply)
• Low Distortion
• Low Noise Figure: 2.0 dB
• 15 dB Gain
• Single +4 V to +9 V Supply
• Wide Bandwidth: 50 MHz to 1 GHz
• SOIC-16 and SOT-89 Package Options
PRODUCT DESCIPTION
The ADA10000 is a monolithic IC intended for use in
applications requiring high linearity, such as Cellular
Telephone Base Station Driver Amplifiers, CA TV Fiber
Receiver and Distribution Amplifiers, and CATV Drop
Amplifiers. Offered in both a modified 16 lead SOIC
package and SOT-89 package, it is well suited for
use in amplifiers where small size, reduced
component count, and high reliability are important.
S24 Package
SOT-89
RF Output
/ Bias
RF Input
2Data Sheet - Rev 2.3
06/2003
ADA10000
Figure 2: Pinout - S3 Package
Table 1: Pin Description - S3 Package
NIP EMAN NOITPIRCSED NIP EMAN NOITPIRCSED
1DNGdnuorG61DNGdnuorG
2DNGdnuorG51DNGdnuorG
3DNGdnuorG41FR
TUO
saiB/tuptuOFR
4DNGdnuorG31DNGdnuorG
5DNGdnuorG21DNGdnuorG
6FR
NI
tupnIFR11DNGdnuorG
7DNGdnuorG01DNGdnuorG
8DNGdnuorG9DNGdnuorG
1
2
GND
RF
OUT
GND
GND
GND
GND
8
7
6
5
4
3
16
15
9
10
11
12
13
14
RF
IN
GND
GND
GND
GND
GND
GND
GND
GND
GND
Data Sheet - Rev 2.3
06/2003
ADA10000
3
Figure 3: Pinout - S24 Package
Table 2: Pin Description - S24 Package
2 31
4
RF
IN
RF
OUT
GND
GND
NIP EMAN NOITPIRCSED
1FR
NI
tupnIFR
2DNGdnuorG
3FR
TUO
saiB/tuptuOFR
4DNGdnuorG
4Data Sheet - Rev 2.3
06/2003
ADA10000
ELECTRICAL CHARACTERISTICS
T able 3: Absolute Minimum and Maximum Ratings
Stresses in excess of the absolute ratings may cause permanent
damage. Functional operation is not implied under these conditions.
Exposure to absolute ratings for extended periods of time may
adversely affect reliability.
T able 4: Operating Ranges
The device may be operated safely over these conditions; however, parametric
performance is guaranteed only over the conditions defined in the electrical
specifications.
Notes:
(1) RF input pin must be AC-coupled. No DC external bias should be
applied.
Notes:
(1) Median time to failure will degrade above this temperature.
RETEMARAP NIM XAM TINU
ylppuS
)41nip:egakcap3S(
)3nip:egakcap42S(
021+CDV
tupnItarewoPFR
)6nip:egakcap3S(
)1nip:egakcap42S(
-01+mBd
erutarepmeTegarotS56-051+C°
RETEMARAP NIM PYT XAM TINU
ycneuqerFtuptuO/tupnIFR05- 0001zHM
V(egatloVylppuS
DD
)4+8+9+CDV
erutarepmeTesaC04--58+
)1(
C°
Data Sheet - Rev 2.3
06/2003
ADA10000
5
T able 5: Electrical Specifications
(TA = +25 °C, VDD = +8 VDC, 75 ΩΩ
ΩΩ
Ω system, see Figures 4 and 5)
Notes:
(1) 160 channels, +17 dBmV per channel (measured at output), 6 MHz channel spacing.
(2) 80 channels, +19 dBmV per channel (measured at output), 6 MHz channel spacing.
( 3 ) Two tones, -10 dBm per tone at input.
( 4) The device can be operated at VDD = +6 VDC for lower power dissipation. Refer to Figures 7, 8, 13, and 16 for
performance variation with supply voltage.
RETEMARAP NIM PYT XAM TINU TNEMMOC
OSC
)1(
OSC/
)2(
26/06--cBd
BTC
)1(
BTC/
)2(
47/56--cBd
niaG4151- Bd
erugiFesioN-0.25.3Bd
tnioPtpecretnItupnIredrOdn2
)2PII(
)3(
92+43+- mBd
tnioPtpecretnItupnIredrOdr3
)3PII(
)3(
31+51+- mBd
ecnatsiseRlamrehT -
-
-
-
53
02 W/C° egakcap3S
egakcap42S
noitpmusnoCtnerruC
)4(
05- 051Am
6Data Sheet - Rev 2.3
06/2003
ADA10000
Figure 4: Test Circuit - S3 Packaged Device (75 ΩΩ
ΩΩ
Ω terminations)
1000 pF
1000 pF
0.1 uF
RFIN
RFOUT
5.6 nH
VDD
3.9 uH
ADA10000
0.5 pF
1000 pF 180 pF
0.5 pF
0.01 uF
RFIN RFOUT
ADA10000
13
2,4
10 nH
100 W50 W
VDD
820 nH
Figure 5: Test Circuit - S24 Packaged Device (75 ΩΩ
ΩΩ
Ω terminations)
Data Sheet - Rev 2.3
06/2003
ADA10000
7
Figure 10: Unmatched Device Input Impedance
S3 Packaged Device
(T = +25 C, V = +8 V, 75 system)
ADD
oW
50 MHz
1 GHz
50 MHz
1 GHz
Figure 11: Unmatched Device Output Impedance
S3 Packaged Device
(T = +25 C, V = +8 V, 75 system)
ADD
oW
PERFORMANCE DA TA
14
16
18
20
22
24
26
024681012
Input Power (dBm)
Output Power (dBm)
Figure 9: Output Power vs. Input Power
S3 Packaged Device
(T = +25 C, V = +8 V, f = 500 MHz, 75 system)
ADD
o
W
12
13
14
15
16
17
18
0 200 400 600 800 1000
Frequency (MHz)
Gain (dB)
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Noise Figure (dB)
Gain
NF
Figure 6: Gain and Noise Figure vs.
Frequency - S3 Packaged Device
(T = +25 C, V = +8 V, 75 system)
ADD
oW
15.0
15.2
15.4
15.6
15.8
16.0
456789
Supply Voltage (V)
Gain (dB)
1.7
1.8
1.9
2.0
2.1
2.2
Noise Figure (dB)
Gain
NF
Figure 7: Gain and Noise Figure vs.
Supply Voltage - S3 Packaged Device
(T = +25 C, f = 500 MHz, 75 system)
A
o
W
5
10
15
20
25
30
35
40
456789
Supply Voltage (V)
IIP2, IIP3 (dBm)
IIP2
IIP3
Figure 8: IIP2 and IIP3 vs. Supply
Voltage - S3 Packaged Device
(T = +25 C, 75 system)
A
o
W
Notes:
1. IIP2 measured at 986.5 MHz; Input = two
tones at 55.25 MHz and 931.25 MHz at -10 dBm.
2. IIP3 measured with two tones at the input: 986.5
MHz and 992.5 MHz at -10 dBm.
Refer to the ANADIGICS web site for full 2-port s-parameter data.
As measured in test circuits shown in Figures 4 and 5.
8Data Sheet - Rev 2.3
06/2003
ADA10000
12
13
14
15
16
17
18
0 200 400 600 800 1000
Frequency (MHz)
Gain (dB)
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Noise Figure (dB)
Gain
NF
Figure 12: Gain and Noise Figure vs.
Frequency - S24 Packaged Device
(T = +25 C, V = +8 V, 75 system)
ADD
o
W
15.0
15.2
15.4
15.6
15.8
16.0
456789
Supply Voltage (V)
Gain (dB)
1.7
1.8
1.9
2.0
2.1
2.2
Noise Figure (dB)
Gain
NF
Figure 13: Gain and Noise Figure vs.
Supply Voltage - S24 Packaged Device
(T = +25 C, f = 500 MHz, 75 system)
A
o
W
-40
-35
-30
-25
-20
-15
-10
-5
0
0 200 400 600 800 1000
Frequency (MHz)
Input Return Loss (dB)
Figure 14: Input Return Loss vs.
Frequency - S24 Packaged Device
(T = +25 C, V = +8 V, 75 system)
ADD
o
W
-40
-35
-30
-25
-20
-15
-10
-5
0
0 200 400 600 800 1000
Frequency (MHz)
Output Return Loss (dB)
Figure 15: Output Return Loss vs.
Frequency - S24 Packaged Device
(T = +25 C, V = +8 V, 75 system)
ADD
o
W
5
10
15
20
25
30
35
40
456789
Supply Voltage (V)
IIP2, IIP3 (dBm)
IIP2
IIP3
Figure 16: IIP2 and IIP3 vs.Supply
Voltage - S24 Packaged Device
(T = +25 C, 75 system)
Ao
W
Notes:
1. IIP2 measured at 986.5 MHz; Input = two
tones at 55.25 MHz and 931.25 MHz at -10 dBm.
2. IIP3 measured with two tones at the input: 986.5
MHz and 992.5 MHz at -10 dBm.
14
16
18
20
22
24
26
024681012
Input Power (dBm)
Output Power (dBm)
Figure 17: Output Power vs. Input Power
S24 Packaged Device
(T = +25 C,V = +8 V, f = 500 MHz, 75 system)
ADD
o
W
Data Sheet - Rev 2.3
06/2003
ADA10000
9
Refer to the ANADIGICS web site for full 2-port s-parameter data.
1GHz
50 MHz
Figure 18: Unmatched Device Input Impedance
S24 Packaged Device
(T = +25 C, V = +8 V, 75 system)
ADD
o
W
1 GHz
50 MHz
Figure 19: Unmatched Device Output Impedance
S24 Packaged Device
(T = +25 C, V = +8 V, 75 system)
ADD
oW
10 Data Sheet - Rev 2.3
06/2003
ADA10000
P ACKAGE OUTLINE
HE
eB1
A
B
A2
L
a
C
LE
0.003 [0.076mm]
A1
GAUGE PLANE
SEATING PLANE
D
0.015 [0.38]X45
a
L
e
E
A
D
B
L
S
O
Y
B
M
MILLIMETERSINCHES
NOTE
MAX.MIN.MAX.MIN.
H
LE
C
2
3
4
1
B
0.020 0.500.330.013
0.10
1.47
0.25
1.730.068
0.010
0.058
0.004
0.055 0.065 1.651.40
0.250.200.0100.008
8080
6.205.740.2440.226
0.380
0.150
0.400
0.160 4.06
10.16
3.81
9.66
0.050 BSC 1.27 BSC
0.016 0.040 0.41 1.02
0.030 0.76
0.062 1.58 1.780.070
4. LEAD THICKNESS AFTER PLATING TO BE 0.013 [0.33mm]
MAXIMUM.
PER SIDE.
1. CONTROLLING DIMENSION: INCHES
2. DIMENSION "D" DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS
AND GATE BURRS SHALL NOT EXCEED 0.006 [0.15mm]
3. DIMENSION "E" DOES NOT INCLUDE INTER-LEAD FLASH OR
PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS
SHALL NOT EXCEED 0.010 [0.25mm] PER SIDE.
NOTES:
A
2
A
1
Figure 20: S3 Package Outline - Modified 16 Pin SOIC
Data Sheet - Rev 2.3
06/2003
ADA10000
11
Figure 21: S24 Package Outline - SOT-89
WARNING
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS
product in any such application without written consent is prohibited.
IMPORTANT NOTICE
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
E-mail: Mktg@anadigics.com
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without
notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are
subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are
assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges
customers to verify that the information they are using is current before placing orders.
Data Sheet - Rev 2.3
06/2003
12
ADA10000
ORDERING INFORMA TION
REBMUNREDRO ERUTAREPMET
EGNAR
EGAKCAP
NOITPIRCSED GNIGAKCAPTNENOPMOC
RTC3S00001ADAC°58+otC°04-CIOSniP61deifidoMleeRdnaepaTeceip005,3
C3S00001ADAC°58+otC°04-CIOSniP61deifidoM)ebutrepseceip05(sebutcitsalP
1Q42S00001ADAC°58+otC°04-egakcaP98-TOSleeRdnaepaTeceip000,1
