NSX ARINC 600 INTRODUCTION MULTICONTACT CONNECTORS NSX-- ARINC 600 / BPX NSX series (defined by ARINC 600 specification) and BPX series (defined by Boeing S280W551 specification) are multipin rack and panel connectors used to connect high performance aeronautical equipments. These two series manufactured by RADIALL show the following characteristics : ' High contact density (up to 800 contacts). ' Numerous contact arrangements. ' Numerous shell polarization possibilities which give maximum security when mating the equipment in the rack. ' Low mating forces. ' Separation of power and signal contacts. ' EMI/RFI shielding provided by shell to shell conductivity. ' Wide range of contact types and sizes. RADIALL has a lot of customers approval for her NSX series. Among them are the airframe manufacturers and equipments manufacturers. MULTICONTACT CONNECTORS NSX-- ARINC 600 RADIALL NSX series offers the following versions : Connectors for rear removable contacts : ' NSX N : plug and receptacle connectors. Non environmental version, inserts without grommet and compound, plugs without groove and O-ring. ' NSX C : plug and receptacle connectors. Non environmental version, inserts with grommet but without compound, plugs without groove and O-ring. ' NSX E : plug and receptacle connectors. Environmental version, inserts with grommet and compound, plugs with groove and O-ring. ' NSX H : plug connectors only. Environmental version, inserts with grommet and compound, plugs without groove and O-ring. Connectors for front removable contacts : ' NSX F : receptacle connectors only. Front release, front removable signal contacts only. Non environmental version, inserts without grommet and compound. ' NSX G : identical to NSX F but with front release front removable signal, power, coax, triax and quadrax contacts. EMI/RFI shielded connectors : shell to shell conductivity. RADIALL offers a wide range of inserts which can be fitted with signal contacts only or with signal, power, coaxial, triaxial, and quadrax contacts. The range of contacts offered allows RADIALL to satisfy any of its customer needs : Sealing boots, sealing plugs, dust caps conductive or non conductive and cavity reducers. Standard tools : crimping tools, positioners, dies, insertion/extraction tools. Signal contact : size 22-crimp, solder tail and wire wrap post. Power contact : size 20-16-12-8-crimp and solder tail (except size 8). Coaxial contact : size 16-8-5-1-crimp and solder tail. Concentric twinax contact : size 8-crimp and solder tail. Fiber optic contact : size 16 and 12. Thermocouple contact : size 22 and 20-crimp. Quadrax contact : size 8 crimp and solder tail. Items in this catalog are covered by French and foreign Patents and/or Patents pending. 4 NSX ARINC 600 DESCRIPTION SHELL RADIALL NSX series offers three metallic shell sizes fitted with polarization hardware offering 216 polarizing possibilities. Plug shell is fitted with inserts for signal (size 22) pin contacts, coax, triax and quadrax power socket contacts. Receptacle shell is fitted with inserts for signal socket contacts, coax, triax and quadrax power pin contacts. The shell flange has bosses on each side and at both ends to locate the connector on the mounting panel. Shell size 1 can be mounted on a front panel or laterally by using the 3 threaded inserts on both side of the connector. The O-ring on the plug shell (environmental) allows the connector pair to be sealed once mated. CONTACT INSERTS Environmental inserts have a wire sealing grommet on the rear face and compound between insert and shell. SHELL CLIP Inserts are replaceable without having an effect on connector intermateability(shell + insert from the same supplier). The different kind of inserts available are : -- Insert for rear release rear removable contacts (colored blue on the terminating face). -- Insert for front release front removable contacts INSULATOR (colored red on their mating face). -- Insert for front release rear removable contacts (colored yellow on their mating face). CONTACTS The contacts are removable from the insert using an appropriate extraction tool. Tools are available for front and rear release inserts. Inserts use a metal contact retention system (clips) which assures the contact retention requirements of ARINC 600 to be met. The retention sytem allows contacts to be removed from the insert using an extraction tool. Signal and power contacts are low insertion force contacts. 5 NSX ARINC 600 CHARACTERISTICS TECHNICAL CHARACTERISTICS DESCRIPTION Shell Inserts MATERIAL PLATING Aluminum alloy Chromatation or nickel Thermosetting resin or thermoplastic / Aluminum alloy Nickel O-ring & grommet Fluorosilicone / Contacts Copper alloy Gold over nickel Retention clip Copper alloy / Insert retention plate Aluminum alloy Blue anodized or nickel Polarization posts and keys retention plate Aluminum alloy Chromatation or nickel Metallic inserts Screws vashers and clinch-nuts clinch nuts Polarization posts and keys Stainless steel / Steel Cadmium yellow chromate Zinc alloy Nickel ELECTRICAL CHARACTERISTICS WIRE CONTACT SIZE AWG CROSS SECTION (mm2) 22 22 24 26 20 OUTSIDE DIA. inches (mm) MAX CURRENT ((A)) min. max. 0.38 0.21 0.14 .026 (0.66) .055 (1.4) 5 3 2 20 22 24 0.60 0.38 0.21 .040 (1) .071 (1.8) 7.5 5 3 16 16 18 20 1.34 0.93 0.60 .066 (1.7) .102 (2.6) 13 10 7.5 12 12 14 16 3.18 1.91 1.34 .094 (2.4) .134 (3.4) 23 17 13 8 8 10 9 5 .183 (4.65) .255 (6.48) 46 33 MECHANICAL AND ENVIRONMENTAL -- Temperature range : -65C/+125C. -- Temperature life : 1000 hours at 125C. -- Salt spray : MIL-STD-1344 method 1001.1 test condition B (48 hours). -- Moisture resistance : MIL-STD-1344 method 1002.1 test condition II (10 times 24 hours). -- Sealing : environment resistant to running water (environmental version only). -- Fluid resistance : resistance to MIL-STD-1344 method 1016 (fluids a, e, i). -- Durability : 500 mating and unmating cycles. -- Random vibration : conforming to MIL-STD-1344 method 2005.1 test condition 5 letter E. -- Shock -- Mating force -- Contact retention force (16,4g from 50 to 2000Hz, 8 hours per direction). : 50g 11 ms half sine.MIL-STD-1344 method 2004.1 3 impacts per direction. : connector size 1 o 27 pounds (120 N) max, connector size 2 o 60 pounds (267 N) max, connector size 3 o 105 pounds (467 N) max. CONTACT SIZE 22 20 16 12 8 coax triax quadrax Retention force min (ounces) 12 20 25 30 25 25 COAX CONTACTS ELECTRICAL CHARACTERISTICS -- Nominal impedance : 508. -- DWV : 1500 VAC -- IR at 25C = 5000 M8. -- V.S.W.R. : Size 5 o 1.3 from DC to 1500 MHz and insertion loss = 0.3 dB, Size 1 o 1.3 from DC to 5000 MHz. 6 NSX ARINC 600 see page 15 NON ENVIRONMENTAL SIZE 1 PLUG SHELL DIMENSIONS see page 15 7 NSX ARINC 600 NON ENVIRONMENTAL SIZE 1 RECEPTACLE SHELL DIMENSIONS see page 17 8 NSX ARINC 600 see pages 15-16 NON ENVIRONMENTAL SIZE 2 PLUG SHELL DIMENSIONS see pages 15-16 9 NSX ARINC 600 see pages 17-18 NON ENVIRONMENTAL SIZE 2 RECEPTACLE SHELL DIMENSIONS see pages 17-18 10 NSX ARINC 600 see pages 15-16 NON ENVIRONMENTAL SIZE 3 PLUG SHELL DIMENSIONS see pages 15-16 11 NSX ARINC 600 see pages 17-18 NON ENVIRONMENTAL SIZE 3 RECEPTACLE SHELL DIMENSIONS see pages 17-18 12 NSX ARINC 600 ENVIRONMENTAL SIZE 1 PLUG AND RECEPTACLE DIMENSIONS see page 17 see page 17 see page 15 see page 15 13 NSX ARINC 600 see pages 17-18 see pages 15-16 ENVIRONMENTAL SIZE 2 & 3 PLUG AND RECEPTACLE DIMENSIONS see pages 17-18 see pages 15-16 14 NSX ARINC 600 Shell size Cavity A B A, PLUG SHELL DIMENSIONS Contact arrangement Contact size Class N mm (inch) max Class E, H, C mm (inch) max 60 22 28 (1.102) 35.5 (1.398) 30T2 4C 1 22 8 5 35.5 (1.398) 36.8 (1.449) 30.5 (1.200) - 30.5 (1.200) ( ) 39.3 (1.547) ( ) 16 5C2 C 12 5 40 22 28 (1.102) 35.5 (1.398) 4 12 30.5 (1.200) 39.3 (1.547) 150 22 28 (1.102) 35.5 (1.398) 22 28 (1.102) 35.5 (1.398) 30 5 (1.200) 30.5 (1 200) 39 3 (1.547) 39.3 (1 547) 121 20 16 120T2 118Q2 73C3 71C1 1C71 2 3 2, 28 (1.102) (1 102) A B A, B, D D, E 22 8 28 (1.102) (1 102) 35.5 (1.398) 36.8 (1.449) 22 28 (1.102) 35.5 (1.398) 8 28 (1.102) 36.8 (1.449) 22 coax 22 1 22 1 28 (1.102) (1 102) 28 (1.102) (1 102) 28 (1.102) (1 102) 35.5 (1.398) 35.5 (1.398) 35.5 (1.398) - 60 20 30.5 (1.200) 39.3 (1.547) 24 12 30.5 (1.200) 39.3 (1.547) 10T10 8 30.5 (1.200) 39.3 (1.547) Q11 8 30.5 (1.200) 39.3 (1.547) C2 1 28 (1.102) - 2C 1 28 (1.102) - C4 1 28 (1.102) - 35 16 30.5 (1.200) 39.3 (1.547) 22 28 (1.102) 110 20 12 36F36 20F12Q8 20F12T8 16 LuxCis 8 16 LuxCis 8 16 LuxCis 30 5 (1.200) 30.5 (1 200) - 30.5 (1.200) 39 (1.535) 30 5 (1.200) 30.5 (1 200) 39 (1.535) (1 535) 30 5 (1.200) 30.5 (1 200) 39 (1.535) (1 535) 15 NSX ARINC 600 Shell size Cavity PLUG SHELL DIMENSIONS Contact arrangement Contact size Class N mm (inch) max Class E, H, C mm (inch) max 100 22 28 (1.102) 35.5 (1.398) 22 85 20 35.5 (1.398) 28 (1.102) ( ) 16 34 20T4 20Q4 20 16 20 8 20 8 39 3 (1.547) 39.3 (1 547) 30 5 (1.200) 30.5 (1 200) 39 3 (1.547) 39.3 (1 547) 30 5 (1.200) 30.5 (1 200) 39 3 (1.547) 39.3 (1 547) 30 5 (1.200) 30.5 (1 200) 39 3 (1.547) 39.3 (1 547) 30 5 (1.200) 30.5 (1 200) 39 3 (1.547) 39.3 (1 547) 20 13C2 16 12 5 6T6 8 30.5 (1.200) 39.3 (1.547) Q6 8 30.5 (1.200) 39.3 (1.547) 28 (1.102) ( ) 36.8 (1.449) ( ) 22 62Q2 Q 16 8 2 3 2, C F C, 68Q2 22 8 28 (1.102) (1 102) 35.5 (1.398) 36.8 (1.449) 20 11Q2 16 30 5 (1.200) 30.5 (1 200) 39 3 (1.547 39.3 (1 547 30 5 (1.200) 30.5 (1 200) 39 3 (1.547 39.3 (1 547 8 30.5 (1.200) 39.3 (1.547) 22 28 (1.102) 35.5 (1.398) 30 5 (1.200) 30.5 (1 200) 39 3 (1.547) 39.3 (1 547) 30.5 (1.200) ( ) 39 (1.535) ( ) 30 5 (1.200) 30.5 (1 200) 39 (1.535) (1 535) 12 8 20 11WQ2 16 12 8 6P6 59 16 12 16 LuxCis 12F5C2 16 5 16 LuxCis 17F12Q2 16 12 5 16 NSX ARINC 600 Shell size Cavity A B A, RECEPTACLE SHELL DIMENSIONS Contact arrangement Contact size Class N mm (inch) max Class E, H, C mm (inch) max Class F mm (inch) Class G mm (inch) 60 22 31 (1.220) 38.9 (1.531) 30.93/29.84 (1.218/1.175) - 40.5 (1.594) 30.93/29.84 (1.218/1.175) 30.93/29.84 (1.218/1.175) 33.45 (1.317) - - 30.93/29.84 (1.218/1.175) 33.45 (1.317) ( ) 43 (1.693) ( ) - 30 93/29 84 30.93/29.84 (1.218/1.175) 30T2 4C 1 22 8 5 31 (1.220) (1 220) 38.9 (1.531) 16 5C2 12 5 C 40 22 31 (1.220) 38.9 (1.531) 30.93/29.84 (1.218/1.175) - 4 12 33.45 (1.317) 43 (1.693) - - 150 22 31 (1.220) 38.9 (1.531) 30.93/29.84 (1.218/1.175) - 22 31 (1.220) 38.9 (1.531) 30.93/29.84 (1.218/1.175) 121 20 33 45 (1.317) 33.45 (1 317) 43 (1.693) (1 693) 33 45 (1.317) 33.45 (1 317) 22 31 (1.220) 38.9 (1.531) 30.93/29.84 (1.218/1.175) - 8 31 (1.220) 40.5 (1.594) 30.93/29.84 (1.218/1.175) - 22 31 (1.220) 38.9 (1.531) 30.93/29.84 (1.218/1.175) - 8 31 (1.220) 40.5 (1.594) 30.93/29.84 (1.218/1.175) - 30.93/29.84 (1.218/1.175) - 30.93/29.84 (1.218/1.175) - - 30.93/29.84 (1.218/1.175) - 16 120T2 118Q2 73C3 71C1 2,, 3 A,, B,, D,, E 1C71 30.93/29.84 ((1.218/1.175)) 22 coax 22 1 22 1 31 (1.220) (1 220) 31 (1.220) (1 220) 31 (1.220) (1 220) 38.9 (1.531) 38.9 (1.531) 38.9 (1.531) 60 20 33.45 (1.317) 43 (1.693) - 30.93/29.84 (1.218/1.175) 24 12 33.45 (1.317) 43 (1.693) - 30.93/29.84 (1.218/1.175) 10T10 8 33.45 (1.317) 43 (1.693) - 30.93/29.84 (1.218/1.175) Q11 8 33.45 (1.317) 43 (1.693) - 30.93/29.84 (1.218/1.175) C2 1 31 (1.220) - - - 2C 1 31 (1.220) - - - C4 1 31 (1.220) - - 30.93/29.84 (1.218/1.175) 35 110 16 33.45 (1.317) 43 (1.693) - 22 31 (1.220) 38.9 (1.531) 30.93/29.84 (1.218/1.175) 20 12 33 45 (1.317) 33.45 (1 317) 43 (1.693) (1 693) 30.93/29.84 ((1.218/1.175)) 33 45 (1.317) 33.45 (1 317) 17 NSX ARINC 600 Shell size Cavity A,, B,, D,, E RECEPTACLE SHELL DIMENSIONS Contact arrangement Contact size Class N mm (inch) max Class E, H, C mm (inch) max Class F mm (inch) Class G mm (inch) 36F36 16 LuxCis 35.5 (1.398) 44 (1.732) - - 35 5 (1.398) 35.5 (1 398) 44 (1.732) (1 732) - 30.93/29.84 (1.218/1.175) 35 5 (1.398) 35.5 (1 398) 44 (1.732) (1 732) - 30.93/29.84 (1.218/1.175) 31 (1.220) 38.9 (1.531) 30.93/29.84 (1.218/1.175) - 40 5 (1.595) 40.5 (1 595) 30 93/29 84 30.93/29.84 (1.218/1.175) 30 93/29 84 30.93/29.84 (1.218/1.175) 33 45 (1.317) 33.45 (1 317) 43 (1.693) (1 693) - 30.93/29.84 (1.218/1.175) 33 45 (1.317) 33.45 (1 317) 43 (1.693) (1 693) - 30.93/29.84 (1.218/1.175) 33 45 (1.317) 33.45 (1 317) 43 (1.693) (1 693) - 30.93/29.84 (1.218/1.175) 33 45 (1.317) 33.45 (1 317) 43 (1.693) (1 693) - 30.93/29.84 (1.218/1.175) 20F12Q8 20F12T8 100 16 LuxCis 8 16 LuxCis 8 22 22 85 20 38.9 (1.531) 31 (1.220) ( ) 16 34 20T4 20Q4 20 16 20 8 20 8 20 13C2 16 12 5 6T6 8 33.45 (1.317) 43 (1.693) - 30.93/29.84 (1.218/1.175) Q6 8 33.45 (1.317) 43 (1.693) - 30.93/29.84 (1.218/1.175) 30 93/29 84 30.93/29.84 (1.218/1.175) 30 93/29 84 30.93/29.84 (1.218/1.175) 40.5 (1.595) 30.93/29.84 (1.218/1.175) 30.93/29.84 (1.218/1.175) 33 45 (1.317) 33.45 (1 317) 43 (1.693) (1 693) - 30.93/29.84 (1.218/1.175) 33 45 (1.317) 33.45 (1 317) 43 (1.693) (1 693) - 30.93/29.84 (1.218/1.175) 33.45 (1.317) 43 (1.693) - - 38.9 (1.531) 30.93/29.84 (1.218/1.175) 22 2, 3 62Q2 Q 16 38.9 (1.531) 31 (1.220) ( ) 8 C, F 68Q2 22 8 31 (1.220) (1 220) 40 5 (1.595) 40.5 (1 595) 38.9 (1.531) 20 11Q2 16 12 8 20 11WQ2 16 12 8 6P6 8 22 59 16 12 31 (1.220) 30.93/29.84 ((1.218/1.175)) 33 45 (1.317) 33.45 (1 317) 43 (1.693) (1 693) 33 45 (1.317) 33.45 (1 317) 35.5 (1.398) ( ) 44 (1.732) ( ) - - 35 5 (1.398) 35.5 (1 398) 44 (1.732) (1 732) - 30.93/29.84 (1.218/1.175) 16 LuxCis 12F5C2 16 5 16 LuxCis 17F12Q2 16 12 5 CLASS F : size 22 contacts are front release, front removable. Other sizes are rear release, rear removable. CLASS G : all contacts are front release, front removable. 18 NSX ARINC 600 SHELL POLARIZATION POSITION OF POLARIZATION KEYS AND POSTS Connectors are shown front side, with "RADIALL" upward Center key Left key Center polarizing post Right key Left polarizing post Right polarizing post POSITION CODING Dark area represents the polarizing post Clear portion represents the key hole 19 NSX ARINC 600 Code number 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 SHELL POLARIZATION RECEPTACLE SHELL PLUG SHELL Left key Center key Right key Left post Center post Right post -4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 1 1 1 1 1 1 2 2 2 2 2 2 3 3 3 3 3 3 4 4 4 4 4 4 5 5 5 5 5 5 6 -4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 3 3 3 3 3 3 3 3 3 3 3 3 3 -4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 -1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 -1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 -1 1 1 1 1 1 6 6 6 6 6 6 5 5 5 5 5 5 4 4 4 4 4 4 3 3 3 3 3 3 2 2 2 2 2 2 1 1 1 1 1 1 6 6 6 6 6 6 5 Code number 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 RECEPTACLE SHELL PLUG SHELL Left key Center key Right key Left post Center post Right post 6 6 6 6 6 1 1 1 1 1 1 2 2 2 2 2 2 3 3 3 3 3 3 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 1 1 1 1 1 1 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 5 5 5 5 5 4 4 4 4 4 4 3 3 3 3 3 3 2 2 2 2 2 2 1 1 1 1 1 1 6 6 6 6 6 6 5 5 5 5 5 5 4 4 4 4 4 4 3 3 3 20 NSX ARINC 600 Code number 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 SHELL POLARIZATION RECEPTACLE SHELL PLUG SHELL Left key Center key Right key Left post Center post Right post 2 2 2 3 3 3 3 3 3 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 1 1 1 1 1 1 2 2 2 2 2 2 3 3 3 3 3 3 4 4 4 4 4 4 5 5 5 5 5 5 6 6 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6 6 6 6 6 6 6 6 6 6 6 6 6 6 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 3 3 3 2 2 2 2 2 2 1 1 1 1 1 1 6 6 6 6 6 6 5 5 5 5 5 5 4 4 4 4 4 4 3 3 3 3 3 3 2 2 2 2 2 2 1 1 1 1 1 1 6 6 6 6 6 6 5 5 Code number 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 RECEPTACLE SHELL PLUG SHELL Left key Center key Right key Left post Center post Right post 6 6 6 6 1 1 1 1 1 1 2 2 2 2 2 2 3 3 3 3 3 3 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 1 1 1 1 1 1 2 2 2 2 2 2 3 3 3 3 3 3 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1 6 5 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 5 5 5 5 4 4 4 4 4 4 3 3 3 3 3 3 2 2 2 2 2 2 1 1 1 1 1 1 6 6 6 6 6 6 5 5 5 5 5 5 4 4 4 4 4 4 3 3 3 3 3 3 2 2 2 2 2 2 21 NSX ARINC 600 MODIFICATION CODE RECEPTACLE SHELL CODE PLUG SHELL 00 All holes All holes Shell size 1 : Qty = 4 Shell size 2 : Qty = 4 Shell size 1 : Qty = 4 Shell size 2 : Qty = 6 01 Shell size 3 : Qty = 8 Shell size 3 : Qty = 10 Size 1 plug is without threaded inserts Available for shell size 1 only 02 All holes Shell size 1 : Qty = 4 Shell size 2 : Qty = 4 Shell size 1 : Qty = 4 Shell size 2 : Qty = 6 03 Shell size 3 : Qty = 8 Shell size 3 : Qty = 10 Size 1 plug is without threaded inserts Available for shell size 1 only Qty = 4 04 Shell sizes 2 and 3 only Shell sizes 2 and 3 only All holes 08 All holes 22 NSX ARINC 600 RECEPTACLE SHELL MODIFICATION CODE CODE PLUG SHELL Shell sizes 2 and 3 only All holes 09 All holes Shell sizes 2 and 3 only All holes 10 All holes Size 1 receptacle is without threaded inserts Size 1 plug is without threaded inserts Shell size 1 : Qty = 4 Shell size 1 : Qty = 4 Shell size 2 : Qty = 6 Shell size 2 : Qty = 4 Shell size 3 : Qty = 10 11 Size 1 plug is without threaded inserts Size 1 receptacle is without threaded inserts 6 holes (4 close to the bosses and 2 at the polarization system level) Shell size 3 : Qty = 8 Available for shell size 2 only Available for shell size 2 only 12 6 holes (4 in to the corner, 2 at the polarization system level) All holes Available for shell size 1 only 13 Available for shell size 3 only Qty = 8 14 23 NSX ARINC 600 MODIFICATION CODE RECEPTACLE SHELL CODE Shell size 2 : Qty = 8 Shell size 3 : Qty = 12 PLUG SHELL Shell size 2 : Qty = 8 Shell size 3 : Qty = 12 15 Available for shell size 2 only 16 Qty = 6 Size 2 and 3 Size 1 O .122 O (3.1) 4 floating eyelets O .122 O (3.1) Size 1 23 4 floating eyelets Qty = 10 Size 2 and 3 Shell without boss 30 Available for shell size 2 only 24 CRIMPING TOOL POSITIONER INS. EXT INS. EXT TOOL (plastic) TOOL (metallic) NSX ARINC 600 SIGNAL, POWER AND GROUND CONTACTS CRIMP TERMINATION RADIALL P/N 282 885 282 886 282 546 MIL SPEC P/N M 81 969/1.01 M 81 969/1.02 M 81 969/1.03 RADIALL P/N 282 549 028 282 549 029 282 515 MIL SPEC P/N M 81 969/14.01 M 81 969/14.02 M 81 969/14.03 RADIALL P/N 282 970 282 971 282 972 MIL SPEC P/N M 22 520/2.23 M 22 520/2.08 M 22 520/1.02 RADIALL P/N 282 281 282 281 282 291 MIL SPEC P/N M 22 520/2.01 M 22 520/2.01 M 22 520/1.01 620 301 620 300 620 310 620 330 620 331 CONTACT SOCKET 1 orange 1 orange 1 orange 2 green 2 red 2 blue 620 200 620 201 620 210 620 230 620 231 PIN SELECTOR 1 orange 1 orange 1 orange 2 green 2 red 2 blue 4--3--3 WIRE STRIPING LENGTH .020 inch (mm) 5--4 .138 (3.5) 5--6--7 5--4--3--2 6--5--4 .236 (6) .157 (4) WIRE OUTSIDE DIAMETER inch (mm) .055 (1.4) .047 (1.2) .071 (1.8) CROSS SECTION (mm2) 0.38--0.21--0.14 0.093--0.055 0.21--0.38--0.60 1.34--0.93--0.60 0.93--0.60--0.38--0.21 WIRE SIZE (AWG) 22--24--26 28--30 24--22--20 16--18--20 18--20--22--24 CONTACT ARRANGEMENT CONTACT SIZE .102 (2.6) .077 (1.97) See shell contact arrangement page 78 to 87 22 22 reduced crimp barrel 20 16 16 reduced crimp barrel 25 CRIMPING TOOL POSITIONER INS. EXT INS. EXT TOOL (plastic) TOOL (metallic) NSX ARINC 600 SIGNAL, POWER AND GROUND CONTACTS CRIMP TERMINATION RADIALL P/N 282 547 MIL SPEC P/N M 81 969/28.02 RADIALL P/N 282 549 004 MIL SPEC P/N M 81 969/14.04 RADIALL P/N 282 972 282 579 MIL SPEC P/N M 22 520/1.02 M 22 520/1.11 M 81 969/19.02 RADIALL P/N 282 291 MIL SPEC P/N M 22 520/1.01 620 340 620 341 SOCKET CONTACT 1 orange 1 orange 2 yellow 620 240 620 241 619 240 (front release rear removable contact) PIN 1 orange 1 orange 1 orange 2 yellow SELECTOR 8--7--6 WIRE STRIPING LENGTH .020 inch (mm) 2 yellow 2--3--4--5 8--7--6 .236 (6) WIRE OUTSIDE DIAMETER inch (mm) .134 (3.4) .094 (2.4) .134 (3.4) CROSS SECTION (mm2) 3.18--1.91--1.34 0.93--0.60--0.38--0.21 3.18--1.91--1.34 WIRE SIZE (AWG) 12--14--16 18--20--22--24 12--14--16 See shell contact arrangement page 78 to 87 CONTACT ARRANGEMENT CONTACT SIZE 12 12 reduced crimp barrel 12 Please note Radiall recommends plastic extraction tool for environmental cavities 22-20-16 and 12 (the metallic extraction tool leads to damage risk of triple silicon web). 26 POSITIONER EXT TOOL (metallic) NSX ARINC 600 SIGNAL, POWER AND GROUND CONTACTS CRIMP TERMINATION RADIALL P/N socket: 282 549 001 pin: 282 549 012 282 549 012 282 540 001 282 548 MIL SPEC P/N socket: M 81 969/28.03 pin: M 81 969/19.03 M 81 969/19.03 M 81 969/28.03 M 81 969/28.01 282 588 282 557 RADIALL P/N MIL SPEC P/N M 22 520/23.09 DIE RADIALL P/N CRIMPING TOOL MIL SPEC P/N M 22 520/23.02 RADIALL P/N 282 296 MIL SPEC P/N M 22 520/23.01 M 22 520/ 23.01 619 370 619 371 616 361 616 366 616 261 616 266 CONTACT SOCKET 1 orange 1 orange 2 brown 2 black 619 270 619 271 (front release rear removable contact) (front release rear removable contact) 1 orange 1 orange 2 brown 2 black PIN WIRE 8--5 1--1 SELECTOR STRIPING LENGTH .020 inch (mm) .453 (11.5) WIRE OUTSIDE DIAMETER inch (mm) .224 (5.7) .134 (3.4) .234 (5.7) CROSS SECTION (mm2) 9--5 3.18--1.91 9--5 WIRE SIZE (AWG) 8--10 12--14 8--10 See shell contact arrangement page 78 to 87 CONTACT ARRANGEMENT CONTACT SIZE .315 (8.0) 8 8 ground 5 27 CRIMPING TOOL POSITIONER INS. EXT TOOL NSX ARINC 600 CHROMEL CONTACTS - CRIMP TERMINATION RADIALL P/N 282 885 282 886 MIL SPEC P/N M 81 969/1.01 M 81 969/1.02 RADIALL P/N 282 970 282 971 MIL SPEC P/N M 22 520/2.23 M 22 520/2.08 RADIALL P/N 282 281 MIL SPEC P/N M 22 520/2.01 620 380 620 390 CONTACT SOCKET 1 orange 1 orange 2 green 2 red 3 yellow 3 yellow 620 280 620 290 PIN 1 orange WIRE SELECTOR 1 orange 2 green 2 red 3 yellow 3 yellow 4--3--3 7--6--5 STRIPING LENGTH .020 inch (mm) .138 (3.5) .157 (4) WIRE OUTSIDE DIAMETER inch (mm) .055 (1.4) .071 (1.8) CROSS SECTION (mm2) 0.38--0.21--0.14 0.60--0.38--0.21 WIRE SIZE (AWG) 22--24--26 20--22--24 See shell contact arrangement page 78 to 87 CONTACT ARRANGEMENT CONTACT SIZE 22 20 28 CRIMPING TOOL POSITIONER INS. EXT TOOL NSX ARINC 600 ALUMEL CONTACTS - CRIMP TERMINATION RADIALL P/N 282 885 282 886 MIL SPEC P/N M 81 969/1.01 M 81 969/1.02 RADIALL P/N 282 970 282 971 MIL SPEC P/N M 22 520/2.23 M 22 520/2.08 RADIALL P/N 282 281 MIL SPEC P/N M 22 520/2.01 620 381 620 391 CONTACT SOCKET 1 orange 1 orange 2 green 2 red 3 black 3 black 620 281 620 291 PIN WIRE SELECTOR 1 orange 1 orange 2 green 2 red 3 black 3 black 4--3--3 7--6--5 STRIPING LENGTH .020 inch (mm) .138 (3.5) .157 (4) WIRE OUTSIDE DIAMETER inch (mm) .055 (1.4) .071 (1.8) CROSS SECTION (mm2) 0.38--0.21--0.14 0.60--0.38--0.21 WIRE SIZE (AWG) 22--24--26 20--22--24 CONTACT ARRANGEMENT CONTACT SIZE See shell contact arrangement page 78 to 87 22 20 29 NSX ARINC 600 WIRE SIZE 1 COAXIAL CONTACTS TYPE PART NUMBER Pin 620 001 CONTACT RG 214 RG 393 CONTACT ARRANGEMENTS WIRING INSTRUCTIONS 71C1--1C71--C2 A (Page 43) 71C1--1C71--C2 Not applicable 620 101 Socket 620 101 001 Identical to 620 101 without O-ring 620 101 003 Not applicable TNC termination Socket 620 101 004 Pin Identical to 620 101 003 without O-ring B (Page 44) 620 003 RG 223 RG 142 71C1--1C7171C1 1C71 -C2 C2 Socket 620 103 C (Page 45) 30 NSX ARINC 600 SIZE 1 COAXIAL CONTACTS WIRE TYPE PART NUMBER RG 402 UT .141 Pin 620 005 CONTACT CONTACT ARRANGEMENTS WIRING INSTRUCTIONS 71C1--1C71--C2 E (Page 47) 71C1--1C7171C1 1C71 -C2 C2 A (Page 43) 620 107 NSA 935 358 Socket 620 107 001 ASNE 0406 WD FILOTEX 50MFCFB and FILECA 1 703/94 Identical to 620 107 without O-ring 620 108 71C1--1C71--C2 Socket 620 108 001 G (Page 48) Identical to 620 108 without O-ring 620 109 RG 400 RG 142 Socket 71C1--1C71--C2 620 109 001 G (Page 48) Identical to 620 109 without O-ring 31 NSX ARINC 600 SIZE 1 COAXIAL CONTACTS WIRE TYPE PART NUMBER CONTACT ARRANGEMENTS WIRING INSTRUCTIONS RG 142 Pin 620 011 71C1--1C71--C2 D (Page 46) Not applicable SMA termination Pin 620 044 71C1--1C71--C2 Not applicable ASNE0691WM Socket 620 101 011 71C1--1C71--C2 TDS contact available at http://www.radiall.com ASNE0692WN Socket 620 101 012 71C1--1C71--C2 TDS contact available at http://www.radiall.com ASNE0692WN ASNE0406WD Pin 620 001 012 71C1--1C71--C2 TDS contact available at http://www.radiall.com RD316 Pin 620 043 001 71C1--1C71--C2 TDS contact available at http://www.radiall.com CONTACT 32 NSX ARINC 600 WIRE TYPE PART NUMBER Socket 619 030 SIZE 8 COAXIAL CONTACTS CONTACT FOR INSERT INS/EXT TOOL WIRING INSTRUCTIONS 282 549 001 H (Page 49) (M 81 969/28.03) ADAMS-RUSSELL FC 11Z (per S280W503--1) 282 549 001 Pin (M 81 969/28.03) for ins. 619 130 282 549 012 (M 81 969/19.03) for ext. Socket 282 549 001 619 031 (M 81 969/28.03) ADAMS-RUSSELL FC 14Z (per S280W503--2) H (Page 49) Front release rear removable contact H (Page 49) 282 549 001 Pin (M 81 969/28.03) for ins. 619 131 282 549 012 (M 81 969/19.03) for ext. H (Page 49) Front release rear removable contact for all size 8 cavities Socket Socket 619 051 619 051 001 environmental Rear release rear removable contact RG400 RG412 RG223 RG55U ASNE0293XF 282 549 001 (M 81 969/28.03) Pin Pin TDS contact available at http://www.radiall.com 619 151 619 151 001 environmental 33 NSX ARINC 600 WIRE TYPE PART NUMBER SIZE 8 COAXIAL CONTACTS CONTACT FOR INSERT INS/EXT TOOL Rear release rear removable contact 619 054 for all size 8 cavities Socket 282 549 001 (M 81 969/28.03) 619 054 001 environmental RG316--KX22 --RG179 ASNE0639XY WIRING INSTRUCTIONS TDS contact available at http://www.radiall.com Rear release rear removable contact 619 154 TDS contact available at http://www.radiall.com for all size 8 cavities Pin Rear release rear removable contact 619 154 001 environmental TDS contact available at http://www.radiall.com 619 053 Rear release rear removable contact for all size 8 cavities Socket 282 549 001 (M 81 969/28.03) 619 053 001 environmental Gore GSC--03--8174 8--00 TDS contact available at http://www.radiall.com Rear release rear removable contact 619 153 TDS contact available at http://www.radiall.com for all size 8 cavities Pin Rear release rear removable contact 619 153 001 environmental TDS contact available at http://www.radiall.com 619 052 Rear release rear removable contact for all size 8 cavities Socket 619 052 001 environmental 282 549 001 (M 81 969/28.03) TDS contact available at http://www.radiall.com Rear release rear removable contact RG180 RG195 619 152 for all size 8 cavities Pi Pin TDS contact available at http://www.radiall.com Rear release rear removable contact 619 152 001 environmental TDS contact available at http://www.radiall.com 34 NSX ARINC 600 WIRE TYPE PART NUMBER SIZE 8 COAXIAL CONTACTS CONTACT FOR INSERT INS/EXT TOOL WIRING INSTRUCTIONS Rear release rear removable contact ASNE0690WL Socket 282 549 001 619 054 002 (M 81 969/28.03) TDS contact available at http://www.radiall.com Rear release rear removable contact 619 050 TDS contact available at http://www.radiall.com Socket Rear release rear removable contact 619 050 001 environmental for all size 8 cavities RG58 RG141 TDS contact available at http://www.radiall.com Rear release rear removable contact 619 150 TDS contact available at http://www.radiall.com Pin Rear release rear removable contact 619 150 001 TDS contact available at http://www.radiall.com environmental Rear release rear removable contact 619 055 TDS contact available at http://www.radiall.com Socket Rear release rear removable contact 619 055 001 environmental RG178 KX21 for all size 8 cavities 619 155 Pi Pin TDS contact available at http://www.radiall.com Rear release rear removable contact TDS contact available at http://www.radiall.com Rear release rear removable contact 619 155 001 environmental TDS contact available at http://www.radiall.com 35 NSX ARINC 600 WIRE TYPE PART NUMBER SIZE 8 COAXIAL CONTACTS CONTACT FOR INSERT INS/EXT TOOL WIRING INSTRUCTIONS Rear release rear removable contact 619 056 TDS contact available at http://www.radiall.com Socket Rear release rear removable contact 619 056 001 environmental for all size 8 cavities RD316 619 156 Pi Pin TDS contact available at http://www.radiall.com Rear release rear removable contact TDS contact available at http://www.radiall.com Rear release rear removable contact 619 156 001 environmental TDS contact available at http://www.radiall.com Add 001 to these P/N to order environmental contacts The above mentioned contacts can be fitted with sealing boots (see available sealing boots on page 69). 36 NSX ARINC 600 WIRE TYPE PART NUMBER Pin 620 120* SIZE 5 COAXIAL CONTACTS CONTACT FOR INSERT RG 58 RG 141 INS/EXT TOOL WIRING INSTRUCTIONS 282 946 P (Page 54) (M 81 969/28.01) Socket 620 020* Pin 620 121* RG 142 RG 223 RG 400 for all size 5 cavities Socket 620 021* Pin 620 122* ASNE0639XY RG 179 RG 316 KX 22 282 946 (M 81 969/28.01) 282 946 (M 81 969/28.01) Socket P (Page 54) R (Page 55) 620 022* * Add 001 to these P/N to order for environmental contacts. 37 NSX ARINC 600 WIRE TYPE PART NUMBER Pin 620 123* SIZE 5 COAXIAL CONTACTS CONTACT FOR INSERT ASNE 0633WG RG 178 KX 21 INS/EXT TOOL WIRING INSTRUCTIONS 282 946 R (Page 55) (M 81 969/28.01) Socket 620 023* Pin 620 124* RG 180 RG 195 282 946 (M 81 969/28.01) Socket P (Page 54) 620 024* for all size 5 cavities Pin 620 126 001 RAYCHEM 5021K1011 282 946 (M 81 969/28.01) Socket 620 026 001 Pin 620 129* 282 946 RD 316 (M 81 969/28.01) Socket L (Page 51) R (Page 55) 620 029* * Add 001 to these P/N to order for environmental contacts. 38 NSX ARINC 600 WIRE TYPE PART NUMBER Pin 620 182 001 SIZE 5 COAXIAL CONTACTS CONTACT FOR INSERT ADAMS-RUSSELL FC 11Z (per S280W503--1) INS/EXT TOOL WIRING INSTRUCTIONS 282 946 L (Page 51) (M 81 969/28.01) Socket 620 082 001 Pin 620 183 001 ADAMS-RUSSELL FC 14Z (per S280W503--2) 282 946 (M 81 969/28.01) Socket 620 083 001 SMA termination Pin 620 134 ASNE0690WL Pin 620 184 ASNE0690WL Pin 620 084 L (Page 51) for all size 5 cavities 282 946 (M 81 969/28.01) 282 946 (M 81 969/28.01) 282 946 (M 81 969/28.01) Not applicable TDS contact available at http://www.radiall.com TDS contact available at http://www.radiall.com 39 NSX ARINC 600 WIRE TYPE PART NUMBER Pin 618 150 SIZE 16 COAXIAL CONTACTS & SIZE 5 CONCENTRIC TWINAX CONTACTS CONTACT FOR INSERT INS/EXT TOOL WIRING INSTRUCTIONS 282 892 S (Page 56) 282 892 T (Page 56) RG 316 RG 179 ASNE0639XY ASNE0632WK ASNE0752WS Socket 618 050 for all size 16 cavities Pin 618 154 RG 178 KX 21 ASNE0633WG Socket 618 054 SIZE 5 CONCENTRIC TWINAX CONTACTS WIRE MIL C 17/17600002 TYPE PART NUMBER Pin 616 195 001* Socket 616 095 001* FOR INSERT INS/EXT TOOL for all size 5 cavities (M 81 969/28.01) 282 946 WIRING INSTRUCTIONS U (Page 57--58) * 616 195 009 and 616 095 009 contacts are the environmental versions of 616 195 001 and 616 095 001. 40 NSX ARINC 600 WIRE TYPE SIZE 8 CONCENTRIC TWINAX CONTACTS INS/EXT TOOL WIRING INSTRUCTIONS 619 165 002 282 549 001 (note 1) (M 81 969/28.03) M (Page 52) PART NUMBER CONTACT FOR INSERT 619 165 Pin Tensolite (S280W502-1) Socket 619 065 282 549 001 Pin 619 166** for all size 8 cavities (M 81 969/28.03) for ins. 282 549 012 (M 81 969/28.03) for ext. M (Page 52) Front release front removable contact Rear release rear removable contact Pin MIL C 17/17600002 619 169 001 619 069 001 TDS contact available at http://www.radiall.com 282 549 001 (M 81 969/28.03) TDS contact available at http://www.radiall.com Socket 619 069 002 environmental Part number in bold letters indicates front release rear removable contact. Note 1 : Contact delivered with a 619 960 alignment boot. Some of the above mentioned contacts can be fitted with sealing boots (see available sealing boots on pages 69 and 115). Pin contacts can be fitted with a 619 960 alignment boot to reduce the splay at the top of the pin contacts (see page 69). 41 NSX ARINC 600 SIZE 8 QUADRAX CONTACTS WIRE TYPE PART NUMBER (non environmental) PART NUMBER (environmental) ABS972 ABS1503KD24 Pin 620 175 010 620 175 011 Socket 620 075 010 620 075 011 Pin 620 179 002 620 179 001 Socket 620 079 002 620 079 001 Pin 620 175 050 620 175 051 Socket 620 075 050 620 075 051 Pin 620 175 021 620 175 020 Socket 620 075 021 620 075 020 THERMAX 956S--4T200 GORE RCN8422 (110 8) TENSOLITE NF24Q100 (100 8) GORE RCN8487--1 (110 8) INS/EXT TOOL 282 549 001 (M 81 969/28.03 or M 81 969/14.06) 969/14 06) WIRING INSTRUCTIONS TDS contact available at http://www.radiall.com Please note quadrax contact are used in these inserts : Q11--68Q4--118Q2--Q6--20Q4--68Q2--62Q2--17F12Q2--11Q2--11WQ2--20F12Q8 42 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS A -- Trim cable at dimensions shown. -- Slide nut washer and gasket over outer jacket. -- Next slide braid clamp until it butts up against outer jacket. -- Comb braid until all strands are straight. -- Next fold braid back over braid clamp as shown. -- Trim dielectric as shown (do not cut inner conductor). -- Trim inner conductor to dimension shown. -- Place contact over inner conductor until it stops agains dielectric. -- Solder in place as shown. -- Insert contact/cable assembly into body assy, slide gasket and washer into body assy. -- Screw clamp nut in place and tighten using 45 to 55 inch. pound torque (5 to 6 m.N). 43 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS B -- Trim cable to dimensions shown. -- Slide nut, washer and gasket over outer jacket. -- Next slide braid clamp until it butts up against outer jacket. -- Comb braid until all strands are straight. -- Next fold braid over braid clamp as shown. -- Slide bushing over dielectric until it stops against braid. -- Trim dielectric as shown. -- Cut inner conductor to dimension shown. -- Assemble insulator and contact over inner conductor until insulator stops against bushing. -- Solder in place as shown -- Insert contact/cable assembly into body assy. -- Slide bushing, braid clamp, gasket and washer into body assy. -- Screw clamp nut in place and tighten using 45 to 55 inch. pound torque (5 to 6 m.N). 44 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS C -- Trim cable to dimensions shown. -- Slide nut, washer and gasket over outer jacket. -- Next slide braid clamp until it butts up against outer jacket -- Comb braid until all strands are straight. -- Next fold braid back over braid clamp as shown. -- Slide bushing over dielectric until it stops against braid. -- Trim dielectric as shown. -- Trim inner conductor to dimension shown -- Assemble insulator and contact over inner conductor until insulator stops against bushing. -- Solder in place as shown. -- Insert contact/cable assembly into body assy, slide bushing, braid clamp, gasket and washer into body assy. -- Screw clamp nut in place and tighten using 45 to 55 inch. pounds torque (5 to 6 m.N). 45 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS D -- Trim cable to dimensions shown. -- Slide nut, washer, gasket over outer jacket. -- Next slide braid clamp until it butts up against outer jacket. -- Comb braid until all strands are straight. next fold braid back over braid clamp as shown. -- Trim dielectric to .300/.330. -- Next trim inner conductor to dimension shown. -- Insert braid clamp, gasket and washer into body assy (make sure outer jacket butts against braid clamp). -- Tighten nut using 45 to 55 inch pounds torque (5 to 6 m.N). -- Next solder inner conductor to contact. -- Close body assy with clamp nut. 46 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS E -- Trim outer jacket and dielectric to dimensions shown. -- Slide center contact over inner conductor while conforming to the 02 dimension requirement. -- Next solder as shown. -- Insert cable/center contact assembly into body assy while conforming to .125 dimension. -- Next solder outer conductor to body assy. 47 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS G -- Strip cable jacket to dimensions shown and remore band between braids for fileca 1763/94 and 1703/93 wire CONTACT 620 108 620 108 001 620 109 620 109 001 620 117, 620 145 620 147, 620 148 A mm (inch) 0 0 8 --0.5 (.31/.29) 26--0.5 (1.02/1.00) 0 A 0 6 --0.5 (.24/.22) 16 --0.5 (.63/.61) 30 0.25 (1.19/1.17) 9 0.25 (.36/.34) 26 0.25 (1.033/1.014) 620 119 102 620 046 B B mm (inch) 5.50 (.216) 13.50 (.531) -- Slide ferrule and nut over the cable and flare the braid. -- Slide crimp barrel fitted with clamp nut over dielectric and place braid on knurled area. (Note : for 620 108, 620 108 001, 620 109, 620 109 001, slide first thermoretractable sheath over cable). -- Slide ferrule over braid maintening a gap (.020 max) between ferrule and clamp nut. crimp ferrule using : CABLE ASNE 0406WD FILOTEX 50MFCFB ECS 311201 FILECA 1703/94 RG214 BA 6903A TIMES AA 5887 CRIMPING TOOL DIE 282 247 M22520/5.61 282 293 M22520/5.29 Hex. A M22520/5.01 TIMES AA 5886 M22520/5.61 RG 400, RG 402 FILECA 1703/93 M22520/5.05 ECS 310801 M22520/5.21 282 246 -- Slide dielectric washer over center conductor then center contact and crimp with : CABLE ASNE 0406WD ECS 311201 RG 214 BA 6903A TIMES AA 5887 FILOTEX 50MFCFB FILECA 1703/94 282 997 M22520/1.13 GREEN 282 291 M22520/1.01 SELECTOR 8 282 997 M22520/1.13 RED 282 972 TIMES AA5886 RG400 FILECA 1703/93 ECS 310801 RG 142 POSITIONER/ TURRET CRIMPING TOOL (M22520/1.02) BLUE 282 997 M22520/1.01 SELECTOR 7 (M22520/1.13) RED 282 296 DANIELS 300 BT 282 586 001 Solder -- Introduce the cable into the outer contact, screw and tighten the clamp nut with 10-15 in. lbs torque (1.1 to 1.7 m.N). 48 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS H -- Trim cable jacket to length indicated : A .010 (0.25) B .010 (0.25) FC 11Z .340 (8.6) .235 (6) FC 14Z .340 (8.6) .215 (5.5) CABLE -- Slide ferrule over the braid. -- Fold back braid. strip inner conductor to dimension shown. -- Introduce inner conductor into center contact sub-assembly. -- Then crimp center contact using : tool : 282 281 (M22520/2.01), selector : 7 for FC 11Z, FC 14Z, positioner : 282 587. -- Slide ferrule until butting. Fold back braid over ferrule as shown -- Introduce this sub assembly into outer contact and push the ferrule until butting. -- Crimp outer contact in the indicated area using : tool : 282 293 (M22520/5.01), die : M22520/5-104 (DANIELS y793). -- During crimping operation push on the ferrule 49 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS J -- Strip cable jacket to dimensions shown. -- Slide nut and ferrule over the cable and flare the braid. slide crimp barrel over dielectric and place braid on knurled area. slide ferrule over braid and crimp using : CABLE CRIMPING TOOL DIE 282 246 RG 142 TIMES AA 6343 ECS 3C142B RG 400 ASNE 0293XF (M22520/5.05) Hex A 282 293 (M22520/5.01) TIMES AA 5888 ECS 311601 or 282 236 (M22520/5.45) Hex B M22520/5.13 Hex A -- Then trim dielectric. -- Slide dielectric washer over center conductor then center contact. -- Crimp center contact using : CABLE RG 142 TIMES AAG 343 ECS 3C 142B RG400 ASHE 0293XF TIMES AA5888 ECS 311301 CRIMPING TOOL POSITIONER/ TURRET 282 291 (M22520/1.01) SELECTOR 7 282 291 282 997 ((M22520/1.13)) GREEN (M22520/1.01) SELECTOR 8 -- Introduce the cable into outer contact, screw and thighten the clamp nut with 10-15 in.Lbs torque (1.1 to 1.7 m.N). 50 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS L -- Put the sealing boot and the shield termination ferrule over the coax cable. Remove .354 .010 on the cable jacket. -- Fold the round braid and the flat braid back over the cable jacket. -- If necessary separate the strands of the flat braid and make the strands straight before you fold them back. -- Remove .260 .010 of the dielectric. -- Put the rear insulator bushing over the center conductor. -- Push the rear insulation bushing until it touches the shield braid. -- Put the center contact over the center conductor and push until it touches the insulator bushing. -- Make sure that you can see the conductor strands through the inspection hole in the center contact. -- Crimp with : tool : 282 281 (M22520/2.01), positioner : 282 550 (DANIELS K345), selector : 5 for FC 11Z cable, 6 for FC 14Z cable, 6 for RAYCHEM 5021K1011. -- Push the shield termination ferrule forward until it touches the shield braids that touch the insulator bushing. -- Put the shield braids symmetrically around the shield te mination ferrule and cut the shield braids at .040 from the edge of the shield termination ferrule. push the cable and center contact assembly into the outer contact assembly until it stops. -- Crimp the outer contact in the area shown. -- Crimp with : tool : 282 293 (M22520/5.01), die : 282 236 (M22520/5-45) Hex B. 51 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS M -- Slide ferrule over outer jacket and trim cable to dimension shown. -- Roll up braids, cut dummy conductors and trim conductors to dimensions shown. -- Slide washer over the 2 conductors until it butts against braids. -- Introduce conductor No 1 into center contact. -- Introduce conductor No 2 into intermediate ferrule. -- Crimp using : tool : 282 293 (M22520/5-01), die : M22520/5-104 (DANIELS Y793). -- Make sure that conductor No 2 is under up die. -- Slide ferrule under braids until it butts against washer. 52 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS M (continued) -- Insert center contact sub assembly into outer body. -- Check center contact position before crimping and crimp in the area shown using : tool : M22520/5-01, die : M22520/5-104 -- After crimping cut braids close to outer body 53 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS P -- Slide ferrule over outer jacket. next trim outer jacket, braid and dielectric to dimensions shown. -- Slide center contact over inner conductor and crimp by using : tool : 282 281 (M22520/2.01), selector : 6 for RG 58 and RG 223, 8 for RG 141, RG 142 and RG 400 positioner : 282 550 (DANIELS K345). -- Flare braid and slide outer contact underneath. -- Slide ferrule over braid and crimp ferrule over outer contact by using : tool : 282 293 (M22520/5.01), die : 282 246 (M22520/5.05) Hex B .177 on flats. 54 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS R -- Trim outer jacket to dimensions shown -- Slide ferrule over braid until it batts up against outer jacket. -- Comb braid until all strands are straight. -- Next fold braid back over ferrule and cut it to dimension shown. -- Next trim dielectric as shown. -- Slide bushing over dielectrique. -- Next slide center contact over inner conductor and crimp with : tool : 282 281 (M22520/2.01), positioner : 282 550 (DANIELS K345), selector : 6 for RG 179, RG 316, RG 178, KX 21 and KX 22 selector : 7 for RD 316 -- Insert contact/cable assembly into outer contact and crimp with : tool : 282 293 (M22520/5.01), die : 282 246 (M22520/5.05) Hex B .177 on flats. 55 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS S -- Trim cable as shown. -- Slide ferrule over sheath flare the braid. -- Insert center conductor into center contact and crimp using : tool : 282 281 (M22520/2.01), positioner : 282 555 (DANIELS K370) selector : 1 for RG 179, ASNE 0639XY selector : 2 for RG 316, ASNE 0752WS and ASNE 0632WK. -- Push cable assembly into contact body and fold braid over barrel. -- Slide ferrule to .020 of shoulder barrel and crimp using : tool : 282 292 (M22520/4.01), positioner : 282 556 WIRING INSTRUCTIONS T -- Trim cable as shown -- Slide ferrule over shea flare the braid. -- Insert center conductor into center contact and crimp using : tool : 282 281 (M22520/2.01), positioner : 282 555 (DANIELS K370) selector : 1 for RG 178, ASNE 0633WG -- Push cable assembly into contact body and fold braid over barrel. -- Slide ferrule to .020 of shoulder barrel and crimp ferrule, turn the contact of about 45 degrees and crimp the ferrule a second time using : tool : 282 292 (M22520/4.01), positioner : 282 556 56 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS U -- For environmental application, before stripping, slide sealing booth over cable. -- For non environmental pin contacts (670 150, 670 151, 618 160 and 618 161), slide alignment boot over cable before stripping. -- Trim cable jacket to length indicated. -- Slide the ferrule over the cable. -- Cut the high immunity ribbon if any fold back braid or braids over the ferrule as indicated. -- Cut braid or braids as shown -- Cut rod fillers -- Strip the two inner conductors -- Introduce the No.2 conductor into the intermediate contact crimp pot crimp the intermediate contact crimp pot : tool : 282 281 (M225520/2-01) positioner : 282 574 selector : 5 -- Put the No.1 cable in the slot of the intermediate contact crimp pot slide the center contact over the conductor crimp the center contact : tool : 282 281 (M22520/2-01) Positioner : 282 576 Selector : 5 57 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS U (continued) -- Install the rear insulator -- Introduce this cable assembly into the contact body sub-assembly -- Crimp the outer contact body in the indicated crimping area : tool : 282 293 (M22520/5-01) Die : 282 236 (M22520/5-45) Hex die closure 8 (.216/flats) DURING THE CRIMPING OPERATION PUSH ON THE CABLE INSPECTION DIMENSION AFTER ASSEMBLY DIMENSIONS CONNECTOR CONTACT A MAX B MAX 616 095 001 .097 (2,46) MIL-C-81659 616 096 004 .152 (3,88) DSX 616 195 001 .078 (1,97) 616 196 003 616 196 004 .033 (0,81) A : distance between the end of outer pin contact and the end of the center pin contact B : distance between the end of outer socket contact and the end of intermediate pin contact 58 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS W -- Strip the cable at dimension shown. -- Slide clamp nut, ring gland, seal and braid clamp over the cable. -- Comb braid until all strands are straight. -- Cut braid to dimension shown. -- Fold back braid over braid clamp. -- Strip and trim inner conductor at dimension shown. -- Place center contact over inner conductor until stops against dielectric. -- Solder center contact. Mounting of the size 1 coax contacts in the connector The C4 insert is composed of : -- 1 front plate -- 1 rear plate -- the insert retention plate Design of rear plate Insert the front plate in the connector. Then, fix it with the insert retention plates; Locate the four coaxial contacts in the corresponding holes of rear plate (the removal of circlips, washer and spring is not necessary). Then, the assembly (contacts and rear plates is insered in the connector and maintained by the two attachment screws. 59 NSX ARINC 600 WIRING INSTRUCTIONS WIRING INSTRUCTIONS Y -- Strip the cable at dimension shown. -- Slide the nut over the cable. -- Introduce the solder ferrule on the dielectric until butting on the cable. -- Solder the ferrule with a 250W max tool then trim dielectric -- Slide dielectric washer on the center conductor then center contact. -- Solder the center contact with a 250W max tool. -- Introduce the cable assembly into the outer contact screw and tighten the nut. 60 NSX ARINC 600 TOOLS CRIMPING TOOLS PART NUMBER CRIMPING TOOLS 282 291 M22520/1.01 282 281 M22520/2.01 282 292 M22520/4.01 282 293 M22520/5.01 / M22520/23.01 / M22520/31.01 POSITIONERS PART NUMBER MIL SPEC P/N 282 972 M22520/1.02 282 579 M22520/1.11 282 997 M22520/1.13 282 971 M22520/2.08 282 970 M22520/2.23 / M22520/23.09 282 550 (DANIELS K345) / 282 555 (DANIELS K370) / 282 556 / 282 587 / 282 588 / PART NUMBER MIL SPEC P/N 282 246 M22520/5.05 / M22520/5.13 / M22520/5.29 282 236 M22520/5.45 282 247 M22520/5.61 / M22520/23.02 / M22520/5.104 DIES 61 NSX ARINC 600 INSERTION/EXTRACTION TOOLS PART NUMBER MIL SPEC P/N DESCRIPTION 282 885 M81969/1.01 ins/ext tool for rear release rear removable size 22 contacts (crimp version) 282 886 M81969/1.02 ins/ext tool for rear release rear removable size 20 contacts (crimp version) 282 546 M81969/1.03 ins/ext tool for rear release rear removable size 16 contacts (crimp version) 282 549 004 M81969/14.04 extraction tool for rear release rear removable size 12 contacts / M81969/19.02 extraction tool for front release rear removable size 12 power contacts / M81969/19.03 extraction tool for front release rear removable size 8 contacts 282 946 M81969/28.01 ins/ext tool for rear release rear removable size 5 coaxial contacts (metallic) 282 549 001 M81969/28.03 extraction tool for rear release rear removable size 8 contacts 282 500 / ins/ext tool for front release front removable size 22 contacts 282 503 / ins/ext tool for front release front removable size 20 contacts 282 504 / ins/ext tool for front release front removable size 16 contacts 282 547 / extraction tool for rear release rear removable size 12 contacts, crimp version 282 548 / extraction tool for rear release rear removable size 5 coaxial contacts 282 549 001 / extraction tool for rear release rear removable size 8 contacts 282 549 005 / ins/ext tool for front release front removable size 12 contacts 282 549 009 / extraction tool for front release front removable size 8 triaxial contacts 282 549 011 / insertion tool for front release front removable size 8 triaxial contacts, solder tail version 282 549 012 / extraction tool for front release rear removable size 8 triaxial contacts 282 890 / ins/ext tool for rear release size 22 contacts solder tail and wire wrap terminations 282 892 / extraction tool for rear release rear removable size 16 coaxial contacts 282 945 / extraction tool for rear release rear removable size 12 coaxial contacts 282 548 / extraction tool for rear release rear removable size 5 coaxial contacts (plastic) 62 NSX ARINC 600 SIZE CONTACT CAVITY TYPE VERSION FILLER PLUGS AND SEALING PLUGS INS EXT COLOR / TYPE non environmental for pin & socket PART NUMBER FIGURE 620 920 rear rear black 616 910 environmental 22 non environmental for socket front Aluminum 620 919 white 620 926 front non environmental non environmental 20 16 for pin & socket rear rear red d environmental 616 911 non environmental 620 922 for pin & socket rear rear blue environmental 616 912 non environmental 620 923 for pin & socket 12 620 921 rear rear yellow 616 913 environmental for pin non environmental front front white 620 936 001 63 NSX ARINC 600 FILLER PLUGS AND SEALING PLUGS SIZE CONTACT CAVITY TYPE VERSION INS EXT COLOR / TYPE PART NUMBER 12 for pin non environmental front front nickel 620 936 002 rear rear nickel 619 953 front front nickel 619 952 nickel 619 950 red 618 915 FIGURE f pin for i non environmental 8 for socket rear for pin & socket rear environmental for pin 620 924 rear for socket rear non environmental white 620 925 5 front front rear rear 620 937 001 for pin & socket environmental red 925 05 560 P/N in bold letters indicates sealing plugs made of aluminum alloy nickel plated. 64 NSX ARINC 600 DUMMY INSERTS When a cavity shell is not fitted with one of the inserts shown on pages 78 to 87, the cavity shell is fitted with a dummy insert. Dummy inserts are made of aluminum alloy and are available for each cavity shell in two kind of plating : ALODINE 1200 or nickel SHELL SIZE CAVITY DUMMY INSERT P/N A or B 620 910 (Alodine 1200) 620 913 001 (nickel) C 620 911 (Alodine 1200) 620 913 002 (nickel) A or B or D or E 620 912 (Alodine 1200) 620 913 003 (nickel) C or F 620 913 (Alodine 1200) 620 913 004 (nickel) FIGURE 1 2&3 65 NSX ARINC 600 DUST CAPS Dust caps are made of thermoplastic. They are available either conductive (black color) or not (red color). ELECTRICAL CHARACTERISTICS SHELL TYPE SHELL SIZE SHELL CAVITY PART NUMBER A/B 620 995 003 C 620 995 004 A/B & D/E 620 995 007 C&F 620 995 008 A/B 620 995 011 C 620 995 012 A/B & D/E 620 995 015 C&F 620 995 016 FIGURE 1 Pl Plug 2&3 C d ti Conductive 1 R Receptacle t l 2&3 66 NSX ARINC 600 ELECTRICAL CHARACTERISTICS DUST CAPS SHELL TYPE SHELL SIZE 1 Plug SHELL CAVITY PART NUMBER A/B 620 995 001 C 620 995 002 SPL 620 995 017 A/B & D/E 620 995 005 C&F 620 995 006 A/B 620 995 009 C 620 995 010 SPL 620 995 018 A/B & D/E 620 995 013 C&F 620 995 014 FIGURE 2&3 Non conductive 1 Receptacle 2&3 67 NSX ARINC 600 CAVITY REDUCERS The following parts are cavity reducers which allows the use of a size 12 contact in a size 5 cavity. These parts are made of copper alloy and are plated with gold over nickel. Once installed, they cannot be removed. ELECTRICAL CHARACTERISTICS PART NUMBER For pin contact 620 940 For socket contact 620 941 For pin contact front release / front removable (FR/FR) connector in version G 620 942 FIGURE 68 NSX ARINC 600 SEALING BOOTS The sealing boots are designed to slide down over the back of the crimped contacts after they have been installed in the connector. The assembly provides bend support and moisture sealing to the contact/cable assembly. Sealing boots are made of fluorosilicone rubber. CAVITY SIZE 5 CABLE OUTSIDE DIA. CABLE PART NUMBER .197 RG 58 RG 141 RG 142 RG 223 RG 400 925.05.553 .150 RG 180 RG 195 925.05.552 .102 & .079 RG 179 RG 316 KX 21 925.05.554 FIGURE ALIGNMENT BOOTS Alignment boots are designed to reduce the play at the top of the size 8 pin contacts. Shall be used with rear release/ rear removable size 8 pin contacts. PART NUMBER : 619 960 69 NSX ARINC 600 PANEL CUT OUT PANEL CUT OUT FOR PLUG SIZE 1, 2 AND 3 70 NSX ARINC 600 PANEL CUT OUT PANEL CUT OUT FOR RECEPTACLE SIZE 1, 2 AND 3 71 NSX ARINC 600 MASS OUNCE (g) SHELLS Includes screws, washers, insert retention plate and polarization hardware. PLUG RECEPTACLE SIZE 1 SIZE 2 SIZE 3 SIZE 1 SIZE 2 SIZE 3 3.88 (110) 4.59 (130) 7.76 (220) 4.59 (130) 4.94 (140) 8.64 (245) INSERTS CONTACT ARRANGEMENT DESIGNATION FOR PLUG SHELL FOR RECEPTACLE SHELL E TYPE N TYPE E TYPE NOR F TYPE 5C2 0.56 (15.75) 0.45 (12.75) 0.36 (10.25) 0.26 (7.25) 40 0.49 (13.75) 0.40 (11.25) / 0.25 (8.00) 60 0.65 (18.50) 0.54 (15.25) 0.44 (12.50) 0.33 (9.25) 30T2 0.65 (18.5) / / 0.34 (9.50) 150 1.46 (41.50) 1.22 (34.50) 0.98 (27.75) 0.72 (20.50) 121 1.65 (46.75) / / 0.85 (24.00) 120T2 1.45 (41.00) 1.20 (34.00) / / 71C1/1C71 1.04 (29.50) 0.91 (25.75) 0.63 (18.00) 0.49 (14.00) 60 / 1.77 (50.25) / 0.93 (26.50) 10T10 / / / / C4 / 1.04 (29.50) / 0.70 (19.80) C2 / 0.97 (27.50) / 0.48 (13.50) 100 1.08 (30.50) 0.90 (25.50) 0.74 (21) 0.53 (15.00) 85 1.18 (33.50) / / 34 1.48 (42.00) 1.24 (35.25) / 0.67 (19.00) 13C2 1.43 (40.50) 1.19 (33.75) 0.86 (24.50) 0.63 (18.00) 6T6 / / / / CONTACTS CONTACT SIZE PIN SOCKET 22 4 10 --3 (0.12) 5.3 10 --3 (0.15) 20 7.8 10 --3 (0.22) 14.1 10 --3 (0.40) 16 25.4 10 --3 (0.72) 26.5 10 --3 (0.75) 12 53.0 10 --3 (1.50) 53.0 10 --3 (1.50) 8 619 270 : 0.18 (5) 619 270 : 0.23 (6.5) 72 NSX ARINC 600 HOW TO ORDER NSX E/N/H/C - CONNECTORS FOR REAR REMOVABLE CONTACTS NSX N 3 P 301 X 00 01 Series Class N: E: H: C: non environmental environmental, with grommets and compound, plug with O-ring environmental, plug without O-ring non environmental, with grommets Shell size 1 : size 1 2 : size 2 3 : size 3 Shell style chromatation R: P: F: B: M: Chromatation plated receptacle Chromatation plated plug Nickel plated receptable Nickel plated plug Nickel plated plug fitted with grouding spring fingers (see pages 102 to 106) Insert combination code See combination code (pages 74 to 77) and contacts arrangements (pages 78 to 87) Contact termination (see note 1) X: S: without contacts crimp contacts Modification code See pages 22 to 24 Polarization code (see note 2) See pages 19 to 21 Impossible part numbers: NSXH--F NSXH--R note 1: Define the signal contact termination code. Power contacts (sizes 8, 12, 16 and 20) will be delivered with crimp termination. If you need to use reduced crimp barrel contacts, use code X and order signal and power contacts separately. Coax and twinax contacts are to be ordered separetely. note 2: Without polarization code, the connector is delivered with polarization hardware unassembled. Polarization code 00, the connector is delivered without polarizing hardware. Polarization code from 01 to 216, the connector is delivered with the polarization hardware assembled as defined by code. Remark: dust caps conductive on receptacle and non conductive on plug are included in the delivery. 73 NSX ARINC 600 INSERT COMBINATION CODE FOR SHELL SIZE 1 INSERT COMBINATION ON SHELL INSERT COMBINATION ON SHELL CODE CODE CAVITY A CAVITY B CAVITY C 109 blank 60 blank 110 60 60 4 5C2 111 blank 30T2 5C2 112 60 4C blank 5C2 113 60 4C 60 blank blank 114 60 107 30T2 30T2 40 115 108 60 60 40 116 CAVITY A CAVITY B CAVITY C 101 60 60 5C2 102 60 60 blank 103 blank 60 104 60 blank 105 blank 106 INSERT COMBINATION ON SHELL CODE CAVITY A CAVITY B CAVITY C 117 blank blank 40 118 60 30T2 5C2 40 119 30T2 blank 5C2 5C2 120 60 30T2 40 40 121 4C 4C 40 blank 40 122 30T2 60 5C2 blank blank blank 4C 60 40 FOR SHELL SIZE 2 INSERT COMBINATION ON SHELL INSERT COMBINATION ON SHELL CODE CODE INSERT COMBINATION ON SHELL CODE CAVITY A CAVITY B CAVITY C CAVITY A CAVITY B 272 150 150 24T4 273 150 C2 13C2 274 C2 71C1 85 275 121 60A 34 13C2 276 121 blank 100 150 6T6 277 1C71 150 13C2 10T10 13C2 278 71C1 1C71 13C2 blank 100 279 150 121 13C2 150 blank blank 280 120T2 121 34 245 71C1 71C1 85 281 150 121 34 blank 246 71C1 blank blank 282 C4 blank 13C2 CAVITY A CAVITY B CAVITY C 201 150 150 13C2 236 C4 C4 34 202 71C1 150 13C2 237 150 120T2 100 203 71C1 71C1 13C2 238 blank 60A 6P6 204 wave guide 150 13C2 239 120T2 120T2 6T6 205 150 71C1 13C2 240 120T2 10T10 206 150 150 100 241 150 207 71C1 150 100 242 150 208 150 71C1 100 243 150 209 71C1 71C1 100 244 210 wave guide 71C1 100 211 150 150 CAVITY C 212 71C1 71C1 blank 247 blank 150 85 283 150 60A 13C2 213 71C1 wave guide 13C2 248 blank 150 100 284 120T2 120T2 13C2 214 wave guide 71C1 13C2 249 blank 150 blank 285 24 60A 100 215 150 73C3 13C2 250 blank 71C1 blank 286 60A 60A 34 216 C2 1C71 85 251 blank blank 100 287 blank 60A 100 217 150 C5 13C2 252 blank wave guide 100 288 blank 121 blank 218 150 wave guide 13C2 253 C2 150 13C2 289 blank blank 85 219 150 2C 13C2 254 C2 1C71 100 290 150 121 100 220 71C1 C2 85 255 C2 1C71 13C2 291 121 150 100 221 1C71 71C1 13C2 256 C2 71C1 13C2 292 121 120 blank 222 blank 150 13C2 257 C2 C2 13C2 293 10T10 10T10 85 223 blank blank 13C2 259 C4 C4 85 294 121 121 13C2 224 150 blank 13C2 260 wave guide 150 85 295 Q11 Q11 85 225 150 71C 1 blank 261 wave guide 150 100 296 121 60A 6P6 226 150 150 85 262 150 60A 34 297 120T2 60A blank 227 150 150 34 263 24 24 6T6 298 121 60A blank 228 C4 150 13C2 264 blank 24 100 299 blank blank 59 229 120T2 120T2 100 265 24 150 13C2 501 24 60A 59 230 121 121 6T6 266 121 121 85 502 121 Q11 Q6 231 121 10T10 6T6 267 24 24 6P6 503 150 blank 11Q2 232 120T2 60A 6P6 268 60A 121 59 504 150 blank 34 233 120T2 150 100 269 10T10 150 13C2 505 Q11 blank 34 234 60A 60A 13C2 270 150 150 59 506 150 150 11Q2 235 150 C4 34 271 C4 120T2 13C2 507 150 150 68Q2 74 NSX ARINC 600 INSERT COMBINATION CODE FOR SHELL SIZE 2 (continued) INSERT COMBINATION ON SHELL INSERT COMBINATION ON SHELL CODE CODE CAVITY A CAVITY B CAVITY A CAVITY C INSERT COMBINATION ON SHELL CODE CAVITY B CAVITY C CAVITY A CAVITY B CAVITY C 508 24 24 100 542 121 C4 Q6 576 150 150 Q6 509 150 Q11 13C2 543 120T2 Q11 13C2 577 1C71 118Q2 12F5C2 510 121 121 100 544 120T2 120T2 24T4 578 150 121 20Q4 511 24 250 100 545 C4 Q11 85 579 C4 120T2 85 512 Q11 Q11 62Q2 546 121 60A 100 580 150 blank 59 513 Q11 Q11 34 547 blank 150 20Q4 581 118Q2 118Q2 20Q4 514 blank 60A 34 548 150 35 20Q4 582 blank 71C1 11Q2 515 blank blank blank 549 24 10T10 13C2 583 150 10T10 59 516 121 121 34 550 10T10 10T10 24T4 584 121 121 59 517 blank 120T2 13C2 551 121 118Q2 24T4 585 20F12Q8 blank 11Q2 518 Q11 blank 62Q2 552 150 Q11 11Q2 586 150 Q11 34 519 Q11 Q11 68Q2 553 10T10 121 100 587 150 118Q2 85 520 150 121 24T4 554 blank 118Q2 13C2 588 Q11 Q11 11Q2 11Q2 521 Q11 150 62Q2 555 blank 71C1 13C2 589 Q11 10T10 522 20F12T8 120T2 13C2 556 blank blank 62Q2 590 blank Q11 Q6 523 10T10 10T10 59 557 blank Q11 62Q2 591 20F12T8 150 100 524 120T2 120T2 11Q2 558 blank Q11 blank 592 blank blank 11Q2 525 24 120T2 6T6 559 150 150 20Q4 594 C4 118Q2 85 526 10T10 10T10 100 560 150 Q11 85 593 20F12Q8 121 blank 527 120T2 120T2 85 561 150 120T2 85 595 Q11 10T10 85 528 150 150 11WQ2 562 121 blank blank 596 blank 118Q2 11WQ2 529 35 35 62Q2 563 24 24 34 597 150 121 Q6 530 24 blank 85 564 blank blank 34 598 20F12Q8 118Q2 13C2 100 531 10T10 24 59 565 150 24 34 599 C4 24 532 20F12T8 121 34 566 150 121 blank 801 C4 Q11 59 533 120T2 C4 24T4 567 150 118Q2 blank 802 blank 120T2 24T4 534 blank Q11 85 568 150 121 6T6 803 Q11 20F12Q8 11Q2 535 150 35 24T4 569 118Q2 118Q2 blank 804 Q11 20F12Q8 17F12Q2 536 blank 150 24T4 570 Q11 150 11Q2 805 10T10 150 85 537 118Q2 118Q2 24T4 571 150 118Q2 13C2 806 C4 60A 59 538 150 120T2 13C2 572 150 C4 13C2 807 Q11 150 85 539 Q11 Q11 blank 573 150 24 13C2 808 150 35 6P6 540 120T2 C4 13C2 574 150 121 59 809 C4 C4 59 541 1C71 Q11 13C2 575 60A 150 34 75 NSX ARINC 600 INSERT COMBINATION CODE FOR SHELL SIZE 3 INSERT COMBINATION ON SHELL INSERT COMBINATION ON SHELL CODE CODE CAVITY A CAVITY B CAVITY C CAVITY D CAVITY E CAVITY F CAVITY A CAVITY B CAVITY C CAVITY D CAVITY E CAVITY F 301 150 150 13C2 150 150 13C2 353 150 150 59 150 150 59 302 150 150 100 150 150 13C2 354 150 150 34 150 24 100 303 150 150 13C2 150 150 100 355 C4 150 13C2 blank 150 13C2 304 150 150 100 150 150 100 356 150 150 100 60A 60A 100 305 150 150 blank 150 150 blank 357 C4 C4 13C2 150 150 100 306 150 71C1 13C2 150 71C1 13C2 358 C4 C4 13C2 121 150 100 307 71C1 71C1 13C2 71C1 71C1 13C2 359 121 121 13C2 121 121 13C2 308 C2 C2 13C2 C2 150 100 360 150 150 6T6 24 24 13C2 309 150 150 13C2 150 71C1 100 361 150 blank 13C2 150 150 blank 310 C4 C4 13C2 blank 150 100 362 24 24 34 150 121 34 311 150 150 85 150 150 85 363 150 150 59 24 60A 59 312 blank blank 13C2 blank blank 13C2 364 60A 24 59 150 150 59 313 blank blank 13C2 blank blank 100 365 24 60A 100 24 60A 100 314 blank blank 13C2 blank 150 100 366 150 150 84 150 150 100 315 150 150 13C2 150 150 blank 367 150 150 59 120T2 120T2 100 316 24 blank 13C2 150 150 blank 368 150 150 59 150 150 34 317 120T2 150 34 120T2 150 34 369 150 150 59 150 150 100 318 121 121 6T6 121 121 6T6 370 60A 60A 100 60A 60A 100 319 121 120T2 6T6 121 120T2 6T6 371 C4 C4 13C2 C2 150 100 320 150 60A 100 150 60A 100 372 150 150 blank 121 blank 13C2 321 150 150 100 150 blank blank 373 150 150 13C2 120T2 120T2 100 322 150 150 100 150 150 34 374 150 150 68Q2 150 150 68Q2 323 150 150 100 71C1 71C1 100 375 150 150 100 150 150 68Q2 324 150 150 100 C2 blank blank 376 150 150 68Q2 150 150 blank 325 150 150 13C2 C2 C2 13C2 377 120T2 150 13C2 120T2 150 100 326 150 71C1 100 150 150 100 378 Q11 150 13C2 150 150 13C2 327 150 71C1 100 150 150 13C2 379 60A 150 34 150 150 34 328 C2 C2 13C2 150 150 13C2 380 C4 120T2 11Q2 C4 120T2 13C2 329 C2 C2 13C2 C4 150 100 381 C4 120T2 11Q2 C4 120T2 11Q2 330 C4 C4 13C2 blank blank blank 382 150 150 11Q2 150 150 11Q2 331 71C1 150 100 150 150 100 383 150 150 blank Q11 150 85 332 C4 C4 13C2 C4 C4 85 384 Q11 150 85 150 150 blank 333 71C1 71C1 100 71C1 71C1 100 385 150 150 59 150 150 6T6 334 71C1 71C1 blank 71C1 71C1 blank 386 150 150 100 150 121 6T6 335 71C1 C4 100 71C1 C4 100 387 Q11 Q11 62Q2 Q11 Q11 62Q2 336 blank 150 13C2 blank 150 13C2 388 Q11 Q11 Q6 Q11 Q11 62Q2 337 blank blank 100 blank blank 13C2 389 Q11 150 11Q2 150 150 68Q2 338 C2 150 100 150 150 100 390 150 150 11Q2 blank blank blank 339 C2 C2 100 C2 C2 100 391 150 150 100 150 10T10 34 340 C2 C2 13C2 C2 C2 13C2 392 10T10 24 59 10T10 24 59 341 C4 C4 100 C4 C4 100 393 blank blank 13C2 150 blank blank 13C2 342 C4 C4 13C2 C4 C4 13C2 394 blank blank 13C2 150 blank 343 blank 150 100 150 150 13C2 395 Q11 Q11 100 Q11 Q11 100 344 24 150 13C2 24 150 13C2 396 blank blank blank blank blank blank 345 60A 24 blank 60A 24 blank 397 Q11 Q11 11Q2 Q11 150 11Q2 346 150 24 100 150 150 34 398 150 120T2 85 150 120T2 85 347 150 150 6T6 121 10T10 13C2 399 121 blank 6T6 60A blank 13C2 348 C4 120T2 100 150 150 13C2 601 60A 60A 13C2 60A 60A 13C2 349 10T10 120T2 100 150 120T2 59 602 Q11 150 11Q2 150 150 11Q2 350 150 120T2 100 150 120T2 59 603 24 blank 13C2 blank blank 13C2 351 150 150 34 150 150 34 604 150 150 blank 150 150 100 352 24 24 100 24 24 34 605 150 Q11 11Q2 150 Q11 68Q2 76 NSX ARINC 600 INSERT COMBINATION CODE FOR SHELL SIZE 3 (continued) INSERT COMBINATION ON SHELL INSERT COMBINATION ON SHELL CODE CODE CAVITY A CAVITY B CAVITY C CAVITY D CAVITY E CAVITY F CAVITY A CAVITY B CAVITY C CAVITY D CAVITY E CAVITY F 607 24 24 13C2 24 24 100 625 150 150 13C2 150 150 608 24 24 13C2 24 24 68Q2 626 C4 C4 13C2 120T2 150 6T6 100 609 150 150 34 150 120T2 13C2 627 C4 120T2 blank C4 120T2 11Q2 610 150 150 34 150 Q11 13C2 628 150 150 11Q2 150 150 6T6 611 blank 150 13C2 blank 150 100 629 C4 120T2 17F12Q2 C4 120T2 11Q2 612 10T10 150 68Q2 150 150 13C2 630 C4 C4 blank C4 C4 34 613 Q11 150 68Q2 150 150 13C2 631 blank 150 13C2 blank Q11 blank 614 150 150 100 blank blank blank 632 blank 150 13C2 150 150 68Q2 615 150 150 100 150 150 59 633 150 150 100 Q11 Q11 11Q2 616 150 150 13C2 60A 120T2 34 634 150 120T2 34 150 120T2 34 617 60A 120T2 13C2 60A 120T2 13C2 635 Q11 121 11Q2 Q11 121 11Q2 618 150 150 Q6 150 150 Q6 636 150 150 11Q2 150 150 100 619 Q11 Q11 11Q2 150 150 100 637 blank 150 11Q2 150 150 68Q2 620 24 24 34 24 blank 34 638 Q11 150 62Q2 Q11 150 62Q2 621 150 150 34 150 60A 34 639 Q11 121 13C2 Q11 121 13C2 622 120T2 150 100 120T2 150 100 640 150 Q11 34 10T10 Q11 34 623 C4 C4 34 C4 C4 blank 641 150 150 blank 150 150 13C2 624 150 150 13C2 60A 60A 34 642 121 60A 59 121 60A 13C2 77 NSX ARINC 600 Insert name Shell size cavity 60 1-A/B 30T2 4C NSX SHELL CONTACT ARRANGEMENT EQUIPMENT SIDE RECEPTACLE SHELL Version N Version E Version F 60x#22 RR/RR 60x#22 RR/RR Version E 28x#22 RR/RR 2x#8G RR/RR 28x#22 RR/RR 2x#8G RR/RR 60x#22 FR/FR 60x#22 RR/RR 60x#22 RR/RR 28x#22 RR/RR 2x#8G RR/RR 28x#22 RR/RR 2x#8G RR/RR 1-A/B 1-A/B Not available 28x#22 FR/FR 2x#8G RR/RR 28x#22 FR/FR 2x#8G FR/FR N/A Not available 4x#5G FR/FR 1-C 4x#5G RR/RR N/A 40x#22 RR/RR 12F12 Version N N/A 4x#5G RR/RR 40 AVIONIC SIDE PLUG SHELL Version G 40x#22 RR/RR 1-C 40x#22 FR/FR N/A 12x#16 RR/RR LUXCIS 12x#16 RR/RR LUXCIS 40x#22 RR/RR 40x#22 RR/RR 12x#16 RR/RR LUXCIS 12x#16 RR/RR LUXCIS N/A 78 NSX ARINC 600 Insert name Shell size cavity 4 1-C EQUIPMENT SIDE RECEPTACLE SHELL Version N 4x#12 FR/RR 5C2 121 120T2 Version E AVIONIC SIDE PLUG SHELL Version F Version G N/A Not available 4x#12 FR/RR 1-C Version N Version E 4x#12 RR/RR 4x#12 RR/RR N/A 2x#5 RR/RR 1x#12 RR/RR 2x#16 RR/RR 150 NSX SHELL CONTACT ARRANGEMENT 2x#5 RR/RR 1x#12 RR/RR 2x#16 RR/RR 2x#5 FR/FR 1x#12 FR/FR 2x#16 FR/FR 2/3-A/B 2x#5 RR/RR 1x#12 RR/RR 2x#16 RR/RR 2x#5 RR/RR 1x#12 RR/RR 2x#16 RR/RR N/A 150x#22 RR/RR 150x#22 RR/RR 150x#22 FR/FR 110x#22 RR/RR 6x#20 RR/RR 5x#16 RR/RR 110x#22 RR/RR 6x#20 RR/RR 5x#16 RR/RR 110x#22 FR/FR 6x#20 RR/RR 5x#16 RR/RR 118x#22 RR/RR 2x#8 RR/RR 118x#22 RR/RR 2x#8 RR/RR 118x#22 FR/FR 2x#8 RR/RR 150x#22 RR/RR 150x#22 RR/RR 110x#22 FR/FR 6x#20 FR/FR 5x#16 FR/FR 110x#22 RR/RR 6x#20 RR/RR 5x#16 RR/RR 110x#22 RR/RR 6x#20 RR/RR 5x#16 RR/RR 118x#22 FR/FR 2x#8 FR/FR 118x#22 RR/RR 2x#8 RR/RR 118x#22 RR/RR 2x#8 RR/RR 2/3-A/B 2/3-A/B 79 NSX ARINC 600 NSX SHELL CONTACT ARRANGEMENT EQUIPMENT SIDE RECEPTACLE SHELL Insert name Shell size cavity Version N Version E Version F 110 2/3-A/B Not available Not available Not available 60 2/3-A/B Version E 100x#22 FR/FR 5x#20 FR/FR 5x#12 FR/FR 100x#22 RR/RR 5x#20 RR/RR 5x#12 RR/RR 100x#22 RR/RR 5x#20 RR/RR 5x#12 RR/RR 60x#20 FR/FR 60x#20 RR/RR 60x#20 RR/RR 35x#16 FR/FR 35x#16 RR/RR 35x#16 RR/RR 24x#12 FR/FR 24x#12 RR/RR 24x#12 RR/RR 10x#8G FR/FR 10x#8G FR/RR 10x#8G FR/RR N/A 35x#16 RR/RR 2/3-A/B N/A 24x#12 RR/RR 10T10 60x#20 RR/RR 2/3-A/B 35x#16 RR/RR 24 Version N N/A 60x#20 RR/RR 35 AVIONIC SIDE PLUG SHELL Version G 24x#12 RR/RR 2/3-A/B N/A 10x#8G FR/RR 10x#8G FR/RR 80 NSX ARINC 600 Insert name Shell size cavity C5 2/3-A/B NSX SHELL CONTACT ARRANGEMENT EQUIPMENT SIDE RECEPTACLE SHELL Version N AVIONIC SIDE PLUG SHELL Version E Version F Version G N/A N/A N/A 5x#SPLG RR/RR C4 2/3-A/B N/A 2/3-A/B N/A 4x#1G FR/FR Not available 2/3-A/B Not available N/A N/A N/A 2x#1G FR/RR N/A 2x#1G FR/RR Not available 70x#22 RR/RR 3x#SPLG RR/RR N/A 2/3-A/B 4x#1G FR/RR Not available 2x#1G FR/RR 2C N/A N/A 70x#22 RR/RR 3x#SPLG RR/RR C2 Version E 5x#SPLG RR/RR 4x#1G FR/RR 73C3 Version N N/A N/A N/A 2x#1G FR/RR 81 NSX ARINC 600 Insert name Shell size cavity 71C1 2/3-A/B EQUIPMENT SIDE RECEPTACLE SHELL Version N 70x#22 RR/RR 1x#1 FR/RR 70x#22 RR/RR 1x#1 FR/RR 2/3-A/B Version N Version E 70x#22 RR/RR 1x#1 FR/RR 70x#22 RR/RR 1x#1 FR/RR 70x#22 RR/RR 1x#1 FR/RR 70x#22 RR/RR 1x#1 FR/RR 36x#16 RR/RR LUXCIS 36x#16 RR/RR LUXCIS 12x#16 RR/RR LUXCIS 8x#8G FR/FR 12x#16 RR/RR LUXCIS 8x#8G RR/RR 12x#16 RR/RR LUXCIS 8x#8G RR/RR 12x#16 RR/RR LUXCIS 8x#8 FR/FR 12x#16 RR/RR LUXCIS 8x#8 RR/RR 12x#16 RR/RR LUXCIS 8x#8 RR/RR 70x#22 FR/FR 1x#1 FR/RR 70x#22 FR/FR 1x#1 FR/RR N/A N/A 36x#16 RR/RR LUXCIS 2/3-A/B N/A 12x#16 RR/RR LUXCIS 8x#8G RR/RR 20F12T8 AVIONIC SIDE PLUG SHELL Version G N/A 36x#16 RR/RR LUXCIS 20F12Q8 Version F 2/3-A/B 70x#22 RR/RR 1x#1 FR/RR 36F36 Version E N/A 70x#22 RR/RR 1x#1 FR/RR 1C71 NSX SHELL CONTACT ARRANGEMENT 12x#16 RR/RR LUXCIS 8x#8G RR/RR 2/3-A/B N/A 12x#16 RR/RR LUXCIS 8x#8 RR/RR 12x#16 RR/RR LUXCIS 8x#8 RR/RR 82 NSX ARINC 600 Insert name Shell size cavity Q11 2/3-A/B EQUIPMENT SIDE RECEPTACLE SHELL Version N 118Q2 100 Version F 11x#8G RR/RR 2/3-A/B Not available 52x#22 RR/RR 6x#16 RR/RR 4x8G RR/RR 52x#22 RR/RR 6x#16 RR/RR 4x8G RR/RR AVIONIC SIDE PLUG SHELL Version G Version N Version E 11x#8G FR/FR 11x#8G RR/RR 11x#8G RR/RR 52x#22 RR/RR 6x#16 RR/RR 4x8G RR/RR 52x#22 RR/RR 6x#16 RR/RR 4x8G RR/RR 118x#22 RR/RR 2x#8G RR/RR 118x#22 RR/RR 2x#8G RR/RR 118x#22 RR/RR 2x#8G RR/RR 118x#22 RR/RR 2x#8G RR/RR 100x#22 RR/RR 100x#22 RR/RR 80x#22 RR/ RR 4x#20 RR/RR # / 80x#22 RR/RR 4x#20 RR/RR 1x#16 RR/RR Not available 2/3-A/B 118x#22 FR/FR 2x#8G RR/RR 2/3-C 118x#22 FR/FR 2x#8G FR/FR N/A 100x#22 RR/RR 85 Version E N/A 11x#8G RR/RR 68Q4 NSX SHELL CONTACT ARRANGEMENT 2/3-C 100x#22 RR/RR 100x#22 FR/FR Not available 80x#22 RR/RR 4x#20 RR/RR 1x#16 RR/RR 80x#22 FR/FR 4x#20 RR/RR 1x#16 RR/RR 80x#22 FR/FR 4x#20 FR/FR 1x#16 FR/FR 83 NSX ARINC 600 NSX SHELL CONTACT ARRANGEMENT EQUIPMENT SIDE RECEPTACLE SHELL AVIONIC SIDE PLUG SHELL Insert name Shell size cavity Version N Version E Version F Version G 84 2/3-C Not available Not available Not available Not available 59 42T4 50x#22 RR/RR 5x#16 RR/RR 4x#12 RR/RR 2/3-C 80x#22 RR/RR 4x#20 RR/RR 80x#22 RR/RR 4x#20 RR/RR 24x#20 RR/RR 10x#16 RR/RR 2/3-C 2/3-C 50x#22 FR/FR 5x#16 RR/RR 4x#12 RR/RR 50x#22 FR/FR 5x#16 FR/FR 4x#12 FR/FR 50x#22 RR/ RR 5x#16 RR/RR # / 50x#22 RR/RR 5x#16 RR/RR 4x#12 RR/RR 24x#20 FR/FR 10x#16 FR/FR 24x#20 RR/RR 10x#16 RR/RR 24x#20 RR/RR 10x#16 RR/RR 6x#8G RR/RR 6x#8G RR/RR N/A 24x#20 RR/RR 10x#16 RR/RR 6T6 Version E 2/3-C 50x#22 RR/RR 5x#16 RR/RR 4x#12 RR/RR 34 Version N N/A 6x#8G FR/RR 6x#8G FR/RR 6x#8G FR/FR Not available Not available Not available 36x#22 FR/FR 2x#16 RR/RR 4x#8G FR/FR Not available 36x#22 RR/RR 2x#16 RR/RR 4x#8G RR/RR 84 NSX ARINC 600 Insert name Shell size cavity 24T4 2/3-C EQUIPMENT SIDE RECEPTACLE SHELL Version N 20x#20 RR/RR 4x8G RR/RR Q6 Version G N/A Not available 20x#20 RR/RR 4x8G RR/RR 6x#8G RR/RR 2/3-C Version N Version E 20x#20 RR/RR 4x8G RR/RR 20x#20 RR/RR 4x8G RR/RR 6x#8G FR/FR 6x#8G RR/RR 6x#8G RR/RR 20x#20 FR/FR 4x#8G FR/FR 20x#20 RR/RR 4x#8G RR/RR 20x#20 RR/RR 4x#8G RR/RR 68x#22 FR/FR 2x#8G FR/FR 68x#22 RR/RR 2x#8G RR/RR 68x#22 RR/RR 2x#8G RR/RR 60x#22 FR/FR 2x#8 FR/FR 2x#8G FR/FR 60x#22 RR/RR 2x#8 RR/RR 2x#8G RR/RR 60x#22 RR/RR 2x#8 RR/RR 2x#8G RR/RR N/A 20x#20 RR/RR 4x#8G RR/RR 2/3-C Not available 68x#22 RR/RR 2x#8G RR/RR 62Q2 AVIONIC SIDE PLUG SHELL Version F N/A 20x#20 RR/RR 4x#8G RR/RR 68Q2 Version E 2/3-C 6x#8G RR/RR 20Q4 NSX SHELL CONTACT ARRANGEMENT 68x#22 RR/RR 2x#8G RR/RR 2/3-C Not available 60x#22 RR/RR 2x#8 RR/RR 2x#8G RR/RR 60x#22 RR/RR 2x#8 RR/RR 2x#8G RR/RR 85 NSX ARINC 600 Insert name Shell size cavity 17F12Q2 2/3-C EQUIPMENT SIDE RECEPTACLE SHELL Version N AVIONIC SIDE PLUG SHELL Version G Version N Version E 12x#16 RR/RR LUXCIS 3x#16 FR/FR 2x#8G FR/FR 12x#16 RR/RR LUXCIS 3x#16 RR/RR 2x#8G RR/RR 12x#16 RR/RR LUXCIS 3x#16 RR/RR 2x#8G RR/RR 4x#20 FR/FR 3x#16 FR/FR 4x#12 FR/FR 2x#8G FR/FR 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#8G RR/RR 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#8G RR/RR 4x#20 FR/FR 3x#16 FR/FR 4x#12 FR/FR 2x#8G FR/FR 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#8G RR/RR 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#8G RR/RR 4x#20 FR/FR 3x#16 FR/FR 4x#12 FR/FR 2x#5 FR/FR 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#5 RR/RR 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#5 RR/RR N/A 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#8G RR/RR 2/3-C N/A 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#8G RR/RR 13C2 Version F 12x#16 RR/RR LUXCIS 3x#16 RR/RR 2x#8G RR/RR 2/3-C 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#8G RR/RR 11WQ2 Version E N/A 12x#16 RR/RR LUXCIS 3x#16 RR/RR 2x#8G RR/RR 11Q2 NSX SHELL CONTACT ARRANGEMENT 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#8G RR/RR 2/3-C N/A 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#5 RR/RR 4x#20 RR/RR 3x#16 RR/RR 4x#12 RR/RR 2x#5 RR/RR 86 NSX ARINC 600 Insert name Shell size cavity 12F5C2 2/3-C EQUIPMENT SIDE RECEPTACLE SHELL Version N 1x#16 RR/RR 5x16 RR/RR LUXCIS 4x#12RR/RR 2x#5 RR/RR 6P6 Version E Version G N/A Not available N/A Version N N/A Version E 1x#16 RR/RR 5x16 RR/RR LUXCIS 4x#12RR/RR 2x#5 RR/RR 1x#16 RR/RR 5x16 RR/RR LUXCIS 4x#12RR/RR 2x#5 RR/RR 6x#8 FR/RR 6x#8 FR/RR Not available 6x#8 FR/RR 2/3-C 25x#16 RR/RR AVIONIC SIDE PLUG SHELL Version F 1x#16 RR/RR 5x16 RR/RR LUXCIS 4x#12RR/RR 2x#5 RR/RR 2/3-C 6x#8 FR/RR 25 NSX SHELL CONTACT ARRANGEMENT Not available 25x#16 RR/RR 25x#16 RR/RR 25x#16 RR/RR notes : -- RR/RR : rear release/rear removable -- FR/FR : front release/front removable -- FR/RR : front release/rear removable -- #8G means cavity size 8 grounded to the shell NSX E/N/H/C -- SIGNAL POWER AND GROUND CONTACTS - CRIMP See pages 25 to 27 NSX E/N/H/C - COAXIAL, TRIAXIAL AND QUADRAX CONTACTS See pages 30 to 42 87 NSX ARINC 600 NSX E/N/H/C - REAR REMOVABLE CONTACTS REAR REMOVABLE PC TAIL CONTACTS SIZE 22 SOCKET CONTACTS PART NUMBER CONTACT TERMINATION 620 305 YA 620 305 005 DIMENSION X inch (mm) C DIA. inch (mm) INS/EXT TOOL .205 (5.20) .165 (4.20) .025 025 (0.635) (0 635) 282 890 DIMENSION X inch (mm) C DIA. inch (mm) INS/EXT TOOL .288 (7.30) .250 (6.30) .025 025 (0.635) (0 635) 282 890 FIGURE ZA SIZE 22 PIN CONTACTS PART NUMBER CONTACT TERMINATION 620 202 Y 620 202 005 FIGURE Z REAR REMOVABLE WIRE WRAP CONTACTS SIZE 22 SOCKET CONTACTS PART NUMBER CONTACT TERMINATION DIMENSION X inch (mm) 620 302 K .303 (7.70) .248 (6.30) 620 303 V .421 (10.70) .366 (9.30) 620 308 W .484 (12.30) .540 (13.70) INS/EXT TOOL FIGURE 282 890 88 NSX ARINC 600 HOW TO ORDER NSX F/G - CONNECTOR FOR FRONT REMOVABLE CONTACTS NSX F 3 R 301 Y 00 01 Series Class F : receptacle connectors, non environmental. For this version, the size 22 contacts cavities only are for front release front release front removable contacts. Signal contacts defined by termination code are delivered installed. Power contacts (size 20, 16, 12) are delivered with crimp termination. Coaxial and twinax contacts are to be ordered separately. G : receptacle connectors, non environmental. For this version, signal (size 22), power (size 20, 16, 12), size 5 coaxial and size 8 coaxial or triaxial contact cavities are for front removable contacts. Size 1 coaxial contacts remain front release/rear removable. Signal and power contacts are delivered installed. Coaxial and twinax contacts are to be ordered separately. Shell size 1 : size 1 2 : size 2 3 : size 3 Shell style R : Alodine 1200 plated receptacle F : Nickel plated receptable Insert combination code (see note 1) Contacts termination X: K: V: W: L: Y: YA : YB : YC : Z: ZA : ZB : ZC : without contacts wire wrap contact, 1 level (1 = .272) wire wrap contact, 2 levels (1 = .390) wire wrap contact, 3 levels (1 = .524) wire wrap contact, 4 levels (1 = .660) pc tail contact length = .250 pc tail contact length = .150 pc tail contact dia length = .375 pc tail contact dia length = .500 pc tail contact length = .250 pre-tinned pc tail contact length = .150 pre-tinned pc tail contact dia length = .375 pre-tinned pc tail contact dia length = .500 pre-tinned Modification code See pages 22 to 24 Polarization code (see note 3) See pages 19 and 21 * Add 001 to these P/N to order dor environmental contacts note 1: See insert combinaison codes on pages 74 to 77 and contact arrangements on pages 78 to 87. note 2: For F version, contact termination code is attributable to signal contacts (size 22) only. For G version, contact termination code is attributable to signal contacts (size 22) to power contacts (size 20, 16, 12) (Power contacts are offered in solder tail version only). note 3: Without termination code, the connector is delivered polarization hardware unassembled. Polarization code 00, the connector is delivered without polarizing hardware. Polarization code from 01 to 216, the connector is delivered with the polarizion hardware assembled as defined by the code. Remark: dust caps conductive on receptacle and are included in the delivery. 89 NSX ARINC 600 NSX F/G - FRONT REMOVABLE PC TAIL CONTACTS SIZE 22 SOCKET CONTACTS PART NUMBER CONTACT TERMINATION 620 360 YA 620 360 005 ZA 620 361 Y 620 361 005 Z 620 362 YB 620 362 005 ZB 620 363 YC 620 363 005 ZC DIMENSION X mm (inch) INS/EXT TOOL COLOR BAND 1 COLOR BAND 2 282 500 orange green FIGURE 4.2/0.4 (.150/.181) 6.8/0.4 (.252/.283) 9.9/0.4 (.374/.406) 13.2/0.4 (.504/.535) SIZE 20 PIN CONTACTS PART NUMBER CONTACT TERMINATION DIMENSION X mm (inch) INS/EXT TOOL COLOR BAND 1 COLOR BAND 2 E DIA mm (inch) 620 214 018 YA 282 503 red d ZA 4.6/3.8 (.181/.150) orange 620 214 019 0.81/0.05 (.030/.034) 620 214 010 Y 282 503 red d Z 6.8/0.4 (.252/.283) orange 620 214 013 0.81/0.05 (.030/.034) 620 214 003 YB 620 214 008 ZB red d YC 282 503 orange 620 214 021 0.81/0.05 (.030/.034) 620 214 022 ZC FIGURE 9.9/0.4 (.374/.405) 13.6/12.8 (.535/.504) SIZE 16 PIN CONTACTS PART NUMBER CONTACT TERMINATION DIMENSION X mm (inch) INS/EXT TOOL COLOR BAND 1 COLOR BAND 2 E DIA mm (inch) 620 234 018 YA 282 504 blue ZA 4.6/3.8 (.181/.150) orange 620 234 019 1.27/0.05 (.048/.052) 620 234 004 Y 282 504 blue Z 6.8/0.4 (.252/.283) orange 620 234 017 1.27/0.05 (.048/.052) 620 234 003 YB 620 234 008 ZB 620 234 021 YC 620 234 022 ZC E 9.9/0.4 (.374/.405) 282 504 13.6/12.8 (.535/.504) FIGURE orange blue 1.27/0.05 (.048/.052) 90 NSX ARINC 600 NSX F/G - FRONT REMOVABLE PC TAIL CONTACTS SIZE 12 PIN CONTACTS PART NUMBER CONTACT TERMINATION DIMENSION X mm(inch) INS/EXT TOOL COLOR BAND 1 COLOR BAND 2 620 244 018 YA 282 549 005 yellow ll ZA 4.6/3.8 (.181/.150) orange 620 244 019 620 244 005 Y 282 549 005 yellow ll Z 6.8/0.4 (.252/.283) orange 620 244 016 620 244 003 YB 620 244 008 ZB yellow ll YC 282 549 005 orange 620 244 021 620 244 022 ZC FIGURE 9.9/0.4 (.374/.405) 13.6/12.8 (.535/.504) SIZE 8 PIN QUADRAX CONTACTS PART NUMBER CONTACT TERMINATION DIMENSION X mm(inch) 620 176 009 YA 3.8/4.6 (.150/.181) 620 176 016* ZA 3.8/5.1 (.150/.200) 620 176 008 Y 6.4/7.2 (.252/.283) 620 176 010* Z 6.4/7.7 (.252/.303) 620 176 011 YB 9.5/10.3 (.374/.405) 620 176 012* ZB 9.5/10.8 (.374/.425) 620 176 013 YC 12.8/13.6 (.504/.535) 620 176 014 ZC 12.8/14.1 (.504/.555) INS/EXT TOOL 282 549 009 SIZE 22 SOCKET FRONT REMOVABLE WIRE WRAP CONTACTS PART NUMBER CONTACT TERMINATION DIMENSION X (inch) mm 620 350 K 6.9/0.4 (.256/.287) 620 351 V 9.9/0.4 (.374/.405) 620 352 W 13.3/0.4 (.508/.540) 620 353 L 16.8/0.4 (.645/.677) INS/EXT TOOL COLOR BAND 1 COLOR BAND 2 282 500 orange green FIGURE * tin lead finish 91 NSX ARINC 600 NSX F/G - FRONT REMOVABLE PC TAIL CONTACTS SIZE 16 PIN COAX CONTACT PART NUMBER CONTACT TERMINATION DIMENSION X inch (mm) 618 155 001 YA 3.8/4.6 (.150/.181) 618 155 002 Y 6.4/7.2 (.252/.283) 618 155 011 YB 9.5/10.3 (.374/.405) PART NUMBER CONTACT TERMINATION DIMENSION X inch (mm) 618 149 017 YA 3.8/4.6 (.150/.181) 618 149 016 Y 6.4/7.2 (.252/.283) INS/EXT TOOL 282 504 SIZE 12 PIN COAX CONTACT 618 149 018 YB 9.5/10.3 (.374/.405) 618 149 012 YC 12.8/13.6 (.503/.535) 618 149 013** ZC 12.8/14.1 (.503/.558) PART NUMBER CONTACT TERMINATION DIMENSION X inch (mm) 619 140 009 YA 3.8/4.6 (.150/.181) 619 140 014** ZA 3.8/5.1 (.150/.200) 619 140 010 Y 6.4/7.2 (.252/.283) 619 140 013** Z 6.4/7.2 (.252/.283) 619 140 007 YB 9.5/10.3 (.374/.405) 619 140 008** ZB 9.5/10.8 (.374/.425) 619 140 011 YC 12.8/13.6 (.503/.535) 619 140 012** ZC 12.8/14.1 (.503/.555) PART NUMBER CONTACT TERMINATION DIMENSION X inch (mm) 620 133 009 YA 3.8/4.6 (.150/.181) 620 133 006 Y 6.4/7.2 (.252/.283) 620 133 001 YB 9.5/10.3 (.374/.405) 620 133 001 YC 12.8/13.6 (.503/.535) INS/EXT TOOL 282 549 005 SIZE 8 PIN COAX CONTACT INS/EXT TOOL 282 549 009 SIZE 5 PIN COAX CONTACT INS/EXT TOOL 282 549 006 ** tin lead finish 92 NSX ARINC 600 NSX F/G - FRONT REMOVABLE PC TAIL CONTACTS SIZE 8 PIN TRIAX PC TAIL FRONT RELEASE VERSION PART NUMBER CONTACT TERMINATION DIMENSION X inch (mm) 619 162 014 YA 3.8/4.6 (.150/.181) 619 162 015** ZA 3.8/5.1 (.150/.200) 619 162 011 Y 6.4/7.2 (.252/.283) 619 162 012** Z 6.4/7.7 (.252/.303) 619 162 016 YB 9.5/10.3 (.374/.405) 619 162 017** ZB 9.5/10.8 (.374/.425) 619 162 009 YC 12.8/13.6 (.503/.535) 619 162 010** ZC 12.8/14.1 (.503/.555) INS/EXT TOOL 282 549 009 SIZE 8 PIN QUADRAX PC TAIL FRONT RELEASE VERSION PART NUMBER CONTACT TERMINATION DIMENSION X inch (mm) 620 176 009 YA 3.8/4.6 (.150/.181) 620 176 016** ZA 3.8/5.1 (.150/.200) 620 176 008 Y 6.4/7.2 (.252/.283) 620 176 010** Z 6.4/7.7 (.252/.303) 620 176 011 YB 9.5/10.3 (.374/.405) 620 176 012** ZB 9.5/10.8 (.374/.425) 620 176 013 YC 12.8/13.6 (.503/.535) 620 176 014** ZC 12.8/14.1 (.503/.555) INS/EXT TOOL 282 549 009 ** tin lead finish 93