FX2M6A-60P-1.27DSAL(71) - Hirose Electric

A113

FX2 Series●1.27mm Pitch Multi-function Two Piece Connector

FX2M6 Series

Series Name : FX2M6

Type No. :A

Number of contacts : 60

Contact Style

P :Header

S :Receptacle

Contact pitch : 1.27mm

DSA :Straight type

L :Board prefixed pin

FX2M6 A - 60 P - 1.27 DSA L

1 3 4 5 6 72

1

2

3

4

5

6

7

■Ordering Imformation

BStacking Variation Unit: mm

Receptacle

Header

FX2C-60P

-1.27DSA

FX2C1-60P

-1.27DSA

FX2C2-60P

-1.27DSA

FX2M6B-60P

-1.27DSAL

FX2M6A-60P

-1.27DSAL

FX2C-60S

-1.27DSA

12

13

14

28.4 *1

34.4 *1

FX2C2-60S

-1.27DSA

14

15

16

30.4 *1

36.4 *1

FX2M6B-60S

-1.27DSAL

28.2

29.2 *2

30.2 *2

44

50

FX2M6A-60S

-1.27DSAL

44.2

45.2 *2

46.2 *2

60

66

Note 1. Mate the male and female connectors to meet the allowable clearance within 1.0mm. However, set it within 0.4mm in

combination *1.

Note 2. In case of combination *2, 0.6mm clearance occurs

on the mating side, but no problem.

Note 3. After the board is mounted, fix the board by screws.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

A114

FX2 Series●1.27mm Pitch Multi-function Two Piece Connector

■Header

BPCB mounting pattern

RoHS

YES

Unit: mm

Part Number

FX2M6A-60P-1.27DSAL(71)

FX2M6B-60P-1.27DSAL(71)

CL No.

572-1036-8-71

572-1041-8-71

A

30.9

24.9

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

A115

FX2 Series●1.27mm Pitch Multi-function Two Piece Connector

Unit: mm

■Receptacle

Part Number

FX2M6A-60S-1.27DSAL(71)

FX2M6B-60S-1.27DSAL(71)

CL No.

572-1037-0-71

572-1042-0-71

ARoHS

35.1

19.1 YES

BPCB mounting pattern

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

A116

FX2 Series●1.27mm Pitch Multi-function Two Piece Connector

BConnection Circuit Diagram

A1an

A2an 1

An a1

······

B1bn

B2bn 1

Bn b1

Connection to Cable 1 Connection to Cable 2

Type A, B

Connection to Cable 1

A1b1

A2b2

An bn

Connection to Cable 2

B1a1

B2a2

Bn an

······

Type A, A

n = Number of Contacts

2

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

A117

FX2 Series●1.27mm Pitch Multi-function Two Piece Connector

BConnecter Use Hand book

1. Selecting connector

1The FX2 series is the perfect flux tight connector for the straight type in the soldering process, but it depends on the soldering

process whether non-cleaning type (FX2C-*, FX2B-*) or cleaning type (FX2CA-*, FX2BA-*) should be selected. Please be

sure to clean the right angle type (FX2-*, FX2B-*) connector. To clean the connector, please be sure to use detergent,

containing no contaminant.

2To use the socket cable type, if a vibration or shock load is applied to the cable, select the lock type. In addition, if a load is

applied to the cable, please be sure to use the cable clamp.

2. Prefixed Process to Board

If the prefixed process is required for mounting the board, please use the prefixed pin type. (Applicable board thickness t = 1.6±0.1)

3. Mating Side Tolerance Clearance

(Example) FX2C-*P-1.27DSA and FX2C-*S-1.27DSA

Note: In order to prevent the dip post breakage in the connector installation to the board, please insert the board in parallel to the

connector so that the prefixed pin may be forcibly pushed in, after the dip post is guided to the board through-hole.

1When the connector is mated,

insert the connector by the end so

as not to make a clearance.

2When the connector is inserted or

extracted, please insert or extract

the connector after the both lock

levers are laid inside. If the

connector is inserted or extracted

with either lock lever laid, the

connector may be broken.

3please do not open the lock lever

outside.

4. Cautions: for Using Lock Cable Type

Set the tolerance clearance within 1mm to

mate the male and female connectors.

(Except for the lock cable type)

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

A118

FX2 Series●1.27mm Pitch Multi-function Two Piece Connector

5. SMT Type Connector Mounting Temperature Profile (Reference)

●IR Reflow

6. SMT Type Connector mated height

As shown in the application pattern, the mated height of the male/female connector doesn't contain the solder paste thickness. Thus,

after the connector installation in the board, consider that the mated height will be widened in proportion to the solder paste

thickness.

150ç

200ç

220ç

Soldering Time

(220çmin)

140

Temperature (ç)

180

220

0

160

200

(MAX 250ç)

240

260

(90 to 120 sec.)

(MAX 60sec.)

Preheating(150 to 200ç) Time (sec.)

HRS test conditions

Test boardGlass epoxy 110mm∞40mm∞1.6mm thick

Solder method : Reflow

Solder composition : Paste,

96.5%Sn/ 3%Ag/ 0.5%Cu

Metal mask : 0.2mm thick (Straight)

0.15mm thick(Right angle)

Reflow cycles : 2 cycles

The temperature profile is based on the above conditions.

In individual applications the actual temperature may vary, depending

on solder paste type, volume/thickness and board size/thickness.

Consult your solder paste and equipment manufacturer for specific

recommendations.

* In regard to the straight type, please contact Hirose Electric about

the recommended open area ratio when using a 0.15mm metal

mask.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.