Technical Data Sheet Chip LED with Right Angle Lens 12-215/G6C-AL2M2B/3C Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mono-color type. Pb-free. The product itself will remain with in RoHS compliant version Descriptions The 12-215 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications. etc. Applications Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Indoor signboard use. Device Selection Guide Chip Part No. Emitted Color Resin Color Brilliant Yellow Green Water Clear Material 12-215/G6C-AL2M2B/3C AlGaInP Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Rev 2 Page: 1 of 10 Prepared by: PAUL 12-215/G6C-AL2M2B/3C Package Outline Dimensions CL 0.6 CL 1.7 2.1 0.8 1.3 0.9 0.35 1.0 0.5 R0.5 0.8 Cathode Mask 0.3 1.5 0.3 Note: The tolerances unless mentioned is 0.1mm, Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Rev 2 Page: 2 of 10 Prepared by: PAUL 12-215/G6C-AL2M2B/3C Absolute Maximum Ratings (Ta=25) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Pd 60 mW ESD 2000 V Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40~ +90 Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @1KHz) Power Dissipation Electrostatic Discharge(HBM) Reflow Soldering : 260 for 10 sec. Hand Soldering : 350 for 3 sec. Electro-Optical Characteristics (Ta=25) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity IV 14.5 ----- 28.5 mcd Peak Wavelength p ---- 575 ---- nm d 569.5 ----- 577.5 nm Dominant Wavelength Spectrum Radiation Bandwidth ----- 20 ---- nm Viewing Angle 21/2 ----- 130 ---- deg Forward Voltage VF 1.75 ----- 2.35 V Reverse Current IR ---- ---- 10 A Condition IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity 11% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.1V Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Rev 2 Page: 3 of 10 Prepared by: PAUL 12-215/G6C-AL2M2B/3C Bin Range Of Dom. Wavelength Groups A Bin Min Max C16 569.5 571.5 C17 571.5 573.5 C18 573.5 575.5 C19 575.5 577.5 Unit Condition nm IF =20mA Unit Condition mcd IF =20mA Unit Condition V IF =20mA Bin Range Of Luminous Intensity Bin Min Max L2 14.5 18.0 M1 18.0 22.5 M2 22.5 28.5 Bin Range Of Forward Voltage Groups B Bin Min Max 0 1.75 1.95 1 1.95 2.15 2 2.15 2.35 Notes: 1.Tolerance of Luminous Intensity 11% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.1V Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Rev 2 Page: 4 of 10 Prepared by: PAUL 12-215/G6C-AL2M2B/3C Electro-Optical Characteristics (Ta=25) Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Rev 2 Page: 5 of 10 Prepared by: PAUL 12-215/G6C-AL2M2B/3C Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Rev 2 Page: 6 of 10 Prepared by: PAUL 12-215/G6C-AL2M2B/3C Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Desiccant Rev 2 Label Page: 7 of 10 Prepared by: PAUL 12-215/G6C-AL2M2B/3C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 2605 Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100 15min 5 min L : -40 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100 5min 10 sec L : -10 5min 300 Cycles 22 PCS. 0/1 Temp. : 100 1000 Hrs. 22 PCS. 0/1 Temp. : -40 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85/ 85% RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Rev 2 Page: 8 of 10 Prepared by: PAUL 12-215/G6C-AL2M2B/3C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30 or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Rev 2 Page: 9 of 10 Prepared by: PAUL 12-215/G6C-AL2M2B/3C 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No: DSE-0002327 Prepared date: 14-Sep-2009 Rev 2 Page: 10 of 10 Prepared by: PAUL