MCP453X/455X/463X/465X 7/8-Bit Single/Dual I2C Digital POT with Volatile Memory Features Description * Single or Dual Resistor Network options * Potentiometer or Rheostat configuration options * Resistor Network Resolution - 7-bit: 128 Resistors (129 Steps) - 8-bit: 256 Resistors (257 Steps) * RAB Resistances options of: - 5 k - 10 k - 50 k - 100 k * Zero-Scale to Full-Scale Wiper operation * Low Wiper Resistance: 75 (typical) * Low Tempco: - Absolute (Rheostat): 50 ppm typical (0C to 70C) - Ratiometric (Potentiometer): 15 ppm typical * I2C Serial interface - 100 kHz, 400 kHz and 3.4 MHz support * Serial protocol allows: - High-Speed Read/Write to wiper - Increment/Decrement of wiper * Resistor Network Terminal Disconnect Feature via the Terminal Control (TCON) Register * Brown-out reset protection (1.5V typical) * Serial Interface Inactive current (2.5 uA typical) * High-Voltage Tolerant Digital Inputs: Up to 12.5V * Wide Operating Voltage: - 2.7V to 5.5V - Device Characteristics Specified - 1.8V to 5.5V - Device Operation * Wide Bandwidth (-3dB) Operation: - 2 MHz (typical) for 5.0 k device * Extended temperature range (-40C to +125C) The MCP45XX and MCP46XX devices offer a wide range of product offerings using an I2C interface. This family of devices support 7-bit and 8-bit resistor networks, Volatile memory configurations, and Potentiometer and Rheostat pinouts. Package Types (top view) MCP45X1 Single Potentiometer HVC / A0 SCL SDA VSS 1 2 3 4 8 7 6 5 VDD P0B P0W P0A MCP45X2 Single Rheostat HVC / A0 SCL SDA VSS 1 2 3 4 MSOP SCL 2 SDA 3 VSS 4 MSOP 8 VDD HVC / A0 1 7 A1 6 P0B 5 P0W EP 9 VDD A1 P0B P0W 8 7 6 5 8 VDD HVC / A0 1 SCL 2 SDA 3 VSS 4 DFN 3x3 (MF) * EP 9 7 A1 6 P0B 5 P0W DFN 3x3 (MF) * HVC/A0 SCL SDA VSS P1B P1W P1A 1 2 3 4 5 6 7 14 13 12 11 10 9 8 TSSOP VDD A1 A2 NC P0B P0W P0A HVC/A0 VDD A1 A2 MCP46X1 Dual Potentiometers 16 15 14 13 SCL SDA VSS VSS 1 2 3 4 EP 17 12 NC 11 NC 10 P0B 9 P0W P1B P1W P1A P0A 5 6 7 8 QFN-16 4x4 (ML) * MCP46X2 Dual Rheostat HVC/A0 SCL SDA VSS P1B 1 2 3 4 5 10 VDD HVC / A0 1 9 A1 SCL 2 8 P0B SDA 3 7 P0W V SS 4 6 P1W P1B 5 MSOP 10 VDD EP 11 9 8 7 6 A1 P0B P0W P1W DFN 3x3 (MF) * * Includes Exposed Thermal Pad (EP); see Table 3-1. (c) 2008 Microchip Technology Inc. DS22096A-page 1 MCP453X/455X/463X/465X Device Block Diagram VDD VSS A2 A1 HVC/A0 SCL SDA 2 I C Interface Power-up/ Brown-out Control Resistor Network 0 (Pot 0) I2C Serial Interface Module & Control Logic (WiperLockTM Technology) Wiper 0 & TCON Register P0A P0W P0B P1A Resistor Network 1 (Pot 1) Memory (16x9) Wiper0 (V & NV) Wiper1 (V & NV) TCON Reserved P1W Wiper 1 & TCON Register P1B For Dual Resistor Network Devices Only I2C RAM No Mid-Scale 5.0, 10.0, 50.0, 100.0 75 129 1.8V to 5.5V MCP4532 (3) 1 Rheostat I2C RAM No Mid-Scale 5.0, 10.0, 50.0, 100.0 75 129 1.8V to 5.5V MCP4541 1 Potentiometer (1) I2C EE Yes NV Wiper 5.0, 10.0, 50.0, 100.0 75 129 2.7V to 5.5V MCP4542 1 Rheostat I2C EE Yes NV Wiper 5.0, 10.0, 50.0, 100.0 75 129 2.7V to 5.5V MCP4551 (3) 1 Potentiometer (1) I2C RAM No Mid-Scale 5.0, 10.0, 50.0, 100.0 75 257 1.8V to 5.5V MCP4552 (3) 1 Rheostat I2C RAM No Mid-Scale 5.0, 10.0, 50.0, 100.0 75 257 1.8V to 5.5V MCP4561 1 Potentiometer (1) I2C EE Yes NV Wiper 5.0, 10.0, 50.0, 100.0 75 257 2.7V to 5.5V MCP4562 1 Rheostat I2C EE Yes NV Wiper 5.0, 10.0, 50.0, 100.0 75 257 2.7V to 5.5V 2 Wiper Configuration RAB Options (k) Wiper - RW () VDD Operating Range (2) MCP4631 (3) 2 Potentiometer I C RAM No Mid-Scale 5.0, 10.0, 50.0, 100.0 75 129 1.8V to 5.5V MCP4632 (3) 2 Rheostat I2C RAM No Mid-Scale 5.0, 10.0, 50.0, 100.0 75 129 1.8V to 5.5V MCP4641 2 Potentiometer (1) I2C EE Yes NV Wiper 5.0, 10.0, 50.0, 100.0 75 129 2.7V to 5.5V MCP4642 2 Rheostat I2C EE Yes NV Wiper 5.0, 10.0, 50.0, 100.0 75 129 2.7V to 5.5V MCP4651 (3) 2 Potentiometer (1) I2C RAM No Mid-Scale 5.0, 10.0, 50.0, 100.0 75 257 1.8V to 5.5V MCP4652 (3) 2 Rheostat I2C RAM No Mid-Scale 5.0, 10.0, 50.0, 100.0 75 257 1.8V to 5.5V 2 I C EE Yes NV Wiper 5.0, 10.0, 50.0, 100.0 75 257 2.7V to 5.5V I2C EE Yes NV Wiper 5.0, 10.0, 50.0, 100.0 75 257 2.7V to 5.5V MCP4661 2 Potentiometer MCP4662 2 Note 1: 2: 3: Rheostat (1) Resistance (typical) # of Steps WiperLock Technology 1 Potentiometer (1) Device POR Wiper Setting Memory Type MCP4531 (3) # of POTs Control Interface Device Features (1) Floating either terminal (A or B) allows the device to be used as a Rheostat (variable resistor). Analog characteristics only tested from 2.7V to 5.5V unless otherwise noted. Please check Microchip web site for device release and availability DS22096A-page 2 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings Voltage on VDD with respect to VSS ............... -0.6V to +7.0V Voltage on HVC/A0, A1, A2, SCL, and SDA with respect to VSS ............................................................................. -0.6V to 12.5V Voltage on all other pins (PxA, PxW, and PxB) with respect to VSS ......................................... -0.3V to VDD + 0.3V Input clamp current, IIK (VI < 0, VI > VDD, VI > VPP ON HV pins) ......................20 mA Output clamp current, IOK (VO < 0 or VO > VDD) ..................................................20 mA Maximum output current sunk by any Output pin ......................................................................................25 mA Maximum output current sourced by any Output pin ......................................................................................25 mA Maximum current out of VSS pin .................................100 mA Maximum current into VDD pin ....................................100 mA Maximum current into PXA, PXW & PXB pins ............2.5 mA Storage temperature ....................................-65C to +150C Ambient temperature with power applied -40C to +125C Total power dissipation (Note 1) ................................400 mW Soldering temperature of leads (10 seconds) ............. +300C ESD protection on all pins .................................. 4 kV (HBM), .......................................................................... 300V (MM) Maximum Junction Temperature (TJ) ......................... +150C Notice: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Note 1: Power dissipation is calculated as follows: PDIS = VDD x {IDD - IOH} + {(VDD-VOH) x IOH} + (VOL x IOL) (c) 2008 Microchip Technology Inc. DS22096A-page 3 MCP453X/455X/463X/465X AC/DC CHARACTERISTICS Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (extended) DC Characteristics Parameters Supply Voltage HVC pin Voltage Range All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25C. Sym Min Typ Max VDD 2.7 -- 5.5 V 1.8 -- 2.7 V VSS -- 12.5V V VSS -- VDD + 8.0V V 1.65 V VHV -- Conditions Serial Interface only. VDD The HVC pin will be at one 4.5V of three input levels V < (VIL, VIH or VIHH). (Note 6) DD 4.5V VDD Start Voltage to ensure Wiper Reset VBOR VDD Rise Rate to ensure Power-on Reset VDDRR Delay after device exits the reset state (VDD > VBOR) TBORD -- 10 20 s IDD -- -- 600 A Serial Interface Active, HVC/A0 = VIH (or VIL) (Note 11) Write all 0's to Volatile Wiper 0 VDD = 5.5V, FSCL = 3.4 MHz -- -- 250 A Serial Interface Active, HVC/A0 = VIH (or VIL) (Note 11) Write all 0's to Volatile Wiper 0 VDD = 5.5V, FSCL = 100 kHz -- 2.5 5 A Serial Interface Inactive, (Stop condition, SCL = SDA = VIH), Wiper = 0 VDD = 5.5V, HVC/A0 = VIH Supply Current (Note 10) -- Units (Note 9) RAM retention voltage (VRAM) < VBOR V/ms Note 1: 2: 3: 4: 5: 6: 7: Resistance is defined as the resistance between terminal A to terminal B. INL and DNL are measured at VW with VA = VDD and VB = VSS. MCP4XX1 only. MCP4XX2 only, includes VWZSE and VWFSE. Resistor terminals A, W and B's polarity with respect to each other is not restricted. This specification by design. Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification DS22096A-page 4 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (extended) DC Characteristics Parameters Resistance ( 20%) Resolution Step Resistance Nominal Resistance Match Wiper Resistance (Note 3, Note 4) All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25C. Sym Min Typ Max Units Conditions RAB 4.0 5 6.0 k -502 devices (Note 1) 8.0 10 12.0 k -103 devices (Note 1) 40.0 50 60.0 k -503 devices (Note 1) 80.0 100 120.0 k -104 devices (Note 1) N 257 Taps 8-bit No Missing Codes 129 Taps 7-bit No Missing Codes -- RAB / (256) -- 8-bit Note 6 -- RAB / (128) -- 7-bit Note 6 |RAB0 - RAB1| / RAB -- 0.2 1.25 % MCP46X1 devices only |RBW0 - RBW1| / RBW -- 0.25 1.5 % MCP46X2 devices only, Code = Full-Scale RW -- 75 160 VDD = 5.5 V, IW = 2.0 mA, code = 00h -- 75 300 VDD = 2.7 V, IW = 2.0 mA, code = 00h -- 50 -- ppm/C TA = -20C to +70C -- 100 -- ppm/C TA = -40C to +85C -- 150 -- ppm/C TA = -40C to +125C ppm/C Code = Midscale (80h or 40h) RS Nominal Resistance Tempco RAB/T Ratiometeric Tempco VWB/T -- 15 -- Resistor Terminal Input Voltage Range (Terminals A, B and W) VA,VW,VB Vss -- VDD V Note 5, Note 6 Note 1: 2: 3: 4: 5: 6: 7: Resistance is defined as the resistance between terminal A to terminal B. INL and DNL are measured at VW with VA = VDD and VB = VSS. MCP4XX1 only. MCP4XX2 only, includes VWZSE and VWFSE. Resistor terminals A, W and B's polarity with respect to each other is not restricted. This specification by design. Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification (c) 2008 Microchip Technology Inc. DS22096A-page 5 MCP453X/455X/463X/465X AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (extended) DC Characteristics Parameters Maximum current through Terminal (A, W or B) Note 6 Leakage current into A, W or B All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25C. Sym Min Typ Max Units IT -- -- 2.5 mA Terminal A IAW, W = Full-Scale (FS) -- -- 2.5 mA Terminal B IBW, W = Zero Scale (ZS) -- -- 2.5 mA Terminal W IAW or IBW, W = FS or ZS -- -- 1.38 mA IAB, VB = 0V, VA = 5.5V, RAB(MIN) = 4000 -- -- 0.688 mA IAB, VB = 0V, VA = 5.5V, RAB(MIN) = 8000 IWL Conditions Terminal A and Terminal B -- -- 0.138 mA -- -- 0.069 mA -- 100 -- nA MCP4XX1 PxA = PxW = PxB = VSS -- 100 -- nA MCP4XX2 PxB = PxW = VSS -- 100 -- nA Terminals Disconnected (R1HW = R0HW = 0) IAB, VB = 0V, VA = 5.5V, RAB(MIN) = 40000 IAB, VB = 0V, VA = 5.5V, RAB(MIN) = 80000 Note 1: 2: 3: 4: 5: 6: 7: Resistance is defined as the resistance between terminal A to terminal B. INL and DNL are measured at VW with VA = VDD and VB = VSS. MCP4XX1 only. MCP4XX2 only, includes VWZSE and VWFSE. Resistor terminals A, W and B's polarity with respect to each other is not restricted. This specification by design. Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification DS22096A-page 6 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (extended) DC Characteristics All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25C. Parameters Sym Full-Scale Error (MCP4XX1 only) (8-bit code = 100h, 7-bit code = 80h) VWFSE Zero-Scale Error (MCP4XX1 only) (8-bit code = 00h, 7-bit code = 00h) VWZSE Potentiometer Integral Non-linearity INL Potentiometer Differential Non-linearity DNL Min Typ Max Units Conditions 5 k 8-bit 3.0V VDD 5.5V 7-bit 3.0V VDD 5.5V 8-bit 3.0V VDD 5.5V 7-bit 3.0V VDD 5.5V -6.0 -0.1 -- LSb -4.0 -0.1 -- LSb -3.5 -0.1 -- LSb -2.0 -0.1 -- LSb -0.8 -0.1 -- LSb 8-bit 3.0V VDD 5.5V -0.5 -0.1 -- LSb 7-bit 3.0V VDD 5.5V -0.5 -0.1 -- LSb 100 k 8-bit 3.0V VDD 5.5V -0.5 -0.1 -- LSb 7-bit 3.0V VDD 5.5V -- +0.1 +6.0 LSb 8-bit 3.0V VDD 5.5V -- +0.1 +3.0 LSb 7-bit 3.0V VDD 5.5V -- +0.1 +3.5 LSb 8-bit 3.0V VDD 5.5V 7-bit 3.0V VDD 5.5V 8-bit 3.0V VDD 5.5V 10 k 50 k 5 k 10 k -- +0.1 +2.0 LSb -- +0.1 +0.8 LSb -- +0.1 +0.5 LSb 7-bit 3.0V VDD 5.5V -- +0.1 +0.5 LSb 100 k 8-bit 3.0V VDD 5.5V -- +0.1 +0.5 LSb 7-bit 3.0V VDD 5.5V 50 k -1 0.5 +1 LSb 8-bit -0.5 0.25 +0.5 LSb 7-bit -0.5 0.25 +0.5 LSb 8-bit -0.25 0.125 +0.25 LSb 7-bit 3.0V VDD 5.5V MCP4XX1 devices only (Note 2) 3.0V VDD 5.5V MCP4XX1 devices only (Note 2) Note 1: 2: 3: 4: 5: 6: 7: Resistance is defined as the resistance between terminal A to terminal B. INL and DNL are measured at VW with VA = VDD and VB = VSS. MCP4XX1 only. MCP4XX2 only, includes VWZSE and VWFSE. Resistor terminals A, W and B's polarity with respect to each other is not restricted. This specification by design. Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification (c) 2008 Microchip Technology Inc. DS22096A-page 7 MCP453X/455X/463X/465X AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (extended) DC Characteristics Parameters Bandwidth -3 dB (See Figure 2-65, load = 30 pF) All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25C. Sym Min Typ Max Units BW -- 2 -- MHz -- 2 -- MHz -- 1 -- MHz -- 1 -- MHz -- 200 -- kHz -- 200 -- kHz -- 100 -- -- 100 -- Conditions 5 k 10 k 8-bit Code = 80h 7-bit Code = 40h 8-bit Code = 80h 7-bit Code = 40h 8-bit Code = 80h 7-bit Code = 40h kHz 100 k 8-bit Code = 80h kHz 7-bit Code = 40h 50 k Note 1: 2: 3: 4: 5: 6: 7: Resistance is defined as the resistance between terminal A to terminal B. INL and DNL are measured at VW with VA = VDD and VB = VSS. MCP4XX1 only. MCP4XX2 only, includes VWZSE and VWFSE. Resistor terminals A, W and B's polarity with respect to each other is not restricted. This specification by design. Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification DS22096A-page 8 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (extended) DC Characteristics All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25C. Parameters Sym Rheostat Integral Non-linearity MCP45X1 (Note 4, Note 8) MCP4XX2 devices only (Note 4) R-INL Min Typ Max Units -1.5 0.5 +1.5 LSb -8.25 +4.5 +8.25 LSb -1.125 0.5 +1.125 LSb -6.0 +4.5 +6.0 LSb -1.5 0.5 +1.5 LSb -5.5 +2.5 +5.5 LSb -1.125 0.5 +1.125 LSb -4.0 +2.5 +4.0 LSb -1.5 0.5 +1.5 LSb -2.0 +1 +2.0 LSb -1.125 0.5 +1.125 LSb -1.5 +1 +1.5 LSb -1.0 0.5 +1.0 LSb -1.5 +0.25 +1.5 LSb -0.8 0.5 +0.8 LSb -1.125 +0.25 +1.125 LSb Conditions 5 k 8-bit 5.5V, IW = 900 A 3.0V, IW = 480 A (Note 7) 7-bit 5.5V, IW = 900 A 3.0V, IW = 480 A (Note 7) 10 k 8-bit 5.5V, IW = 450 A 3.0V, IW = 240 A (Note 7) 7-bit 5.5V, IW = 450 A 3.0V, IW = 240 A (Note 7) 50 k 8-bit 5.5V, IW = 90 A 3.0V, IW = 48 A (Note 7) 7-bit 5.5V, IW = 90 A 3.0V, IW = 48 A (Note 7) 100 k 8-bit 5.5V, IW = 45 A 3.0V, IW = 24 A (Note 7) 7-bit 5.5V, IW = 45 A 3.0V, IW = 24 A (Note 7) Note 1: 2: 3: 4: 5: 6: 7: Resistance is defined as the resistance between terminal A to terminal B. INL and DNL are measured at VW with VA = VDD and VB = VSS. MCP4XX1 only. MCP4XX2 only, includes VWZSE and VWFSE. Resistor terminals A, W and B's polarity with respect to each other is not restricted. This specification by design. Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification (c) 2008 Microchip Technology Inc. DS22096A-page 9 MCP453X/455X/463X/465X AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (extended) DC Characteristics All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25C. Parameters Sym Min Typ Max Units Rheostat Differential Non-linearity MCP45X1 (Note 4, Note 8) MCP4XX2 devices only (Note 4) R-DNL -0.5 -1.0 0.25 +0.5 LSb +0.5 +1.0 LSb -0.375 0.25 +0.375 LSb -0.75 +0.5 +0.75 LSb -0.5 0.25 +0.5 LSb -1.0 +0.25 +1.0 LSb -0.375 0.25 +0.375 LSb -0.75 +0.5 +0.75 LSb -0.5 0.25 +0.5 LSb -0.5 0.25 +0.5 LSb -0.375 0.25 +0.375 LSb -0.375 0.25 +0.375 LSb -0.5 0.25 +0.5 LSb -0.5 0.25 +0.5 LSb -0.375 0.25 +0.375 LSb -0.375 0.25 +0.375 LSb Conditions 5 k 8-bit 5.5V, IW = 900 A 3.0V, IW = 480 A (Note 7) 7-bit 5.5V, IW = 900 A 3.0V, IW = 480 A (Note 7) 10 k 8-bit 5.5V, IW = 450 A 3.0V, IW = 240 A (Note 7) 7-bit 5.5V, IW = 450 A 3.0V, IW = 240 A (Note 7) 50 k 8-bit 5.5V, IW = 90 A 3.0V, IW = 48 A (Note 7) 7-bit 5.5V, IW = 90 A 3.0V, IW = 48 A (Note 7) 100 k 8-bit 5.5V, IW = 45 A 3.0V, IW = 24 A (Note 7) 7-bit 5.5V, IW = 45 A 3.0V, IW = 24 A (Note 7) Capacitance (PA) CAW -- 75 -- pF f =1 MHz, Code = Full-Scale Capacitance (Pw) CW -- 120 -- pF f =1 MHz, Code = Full-Scale Capacitance (PB) CBW -- 75 -- pF f =1 MHz, Code = Full-Scale Note 1: 2: 3: 4: 5: 6: 7: Resistance is defined as the resistance between terminal A to terminal B. INL and DNL are measured at VW with VA = VDD and VB = VSS. MCP4XX1 only. MCP4XX2 only, includes VWZSE and VWFSE. Resistor terminals A, W and B's polarity with respect to each other is not restricted. This specification by design. Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification DS22096A-page 10 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (extended) DC Characteristics Parameters All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25C. Sym Min Typ Max Units Conditions Digital Inputs/Outputs (SDA, SCK, HVC/A0, A1, A2, WP) Schmitt Trigger High Input Threshold Schmitt Trigger Low Input Threshold Hysteresis of Schmitt Trigger Inputs (Note 6) High Voltage Limit VIH VIL VHYS VMAX 0.45 VDD -- -- V 0.5 VDD -- -- V 0.7 VDD -- VMAX V 0.7 VDD -- VMAX V 0.7 VDD -- VMAX V 0.7 VDD -- VMAX V -- -- 0.2VDD V -0.5 -- 0.3VDD V -0.5 -- 0.3VDD V -0.5 -- 0.3VDD V -0.5 -- 0.3VDD V -- 0.1VDD -- V N.A. -- -- V N.A. -- -- V 0.1 VDD -- -- V 0.05 VDD -- -- V 0.1 VDD -- -- V 0.1 VDD -- -- V -- -- 12.5 (6) V All Inputs except SDA and SCL 2.7V VDD 5.5V (Allows 2.7V Digital VDD with 5V Analog VDD) 1.8V VDD 2.7V 100 kHz SDA and SCL 400 kHz 1.7 MHz 3.4 Mhz All inputs except SDA and SCL 100 kHz SDA and SCL 400 kHz 1.7 MHz 3.4 Mhz All inputs except SDA and SCL 100 kHz SDA and SCL 400 kHz VDD < 2.0V VDD 2.0V VDD < 2.0V VDD 2.0V 1.7 MHz 3.4 Mhz Pin can tolerate VMAX or less. Note 1: 2: 3: 4: 5: 6: 7: Resistance is defined as the resistance between terminal A to terminal B. INL and DNL are measured at VW with VA = VDD and VB = VSS. MCP4XX1 only. MCP4XX2 only, includes VWZSE and VWFSE. Resistor terminals A, W and B's polarity with respect to each other is not restricted. This specification by design. Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification (c) 2008 Microchip Technology Inc. DS22096A-page 11 MCP453X/455X/463X/465X AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (extended) DC Characteristics Parameters All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25C. Sym Output Low Voltage (SDA) VOL Weak Pull-up / Pull-down Current IPU HVC Pull-up / Pull-down Resistance Input Leakage Current Pin Capacitance Min Typ Max Units Conditions VSS -- 0.2VDD V VDD < 2.0V, IOL = 1 mA VSS -- 0.4 V VDD 2.0V, IOL = 3 mA -- -- 1.75 mA Internal VDD pull-up, VIHH pull-down VDD = 5.5V, VIHH = 12.5V -- 170 -- A HVC pin, VDD = 5.5V, VHVC = 3V RHVC -- 16 -- k VDD = 5.5V, VHVC = 3V IIL -1 -- 1 A VIN = VDD and VIN = VSS CIN, COUT -- 10 -- pF fC = 3.4 MHz N 0h -- 1FFh hex 8-bit device -- 1FFh RAM (Wiper) Value Value Range 0h TCON POR/BOR Value 1FFh NTCON hex 7-bit device hex All Terminals connected Power Requirements Power Supply Sensitivity (MCP45X2 and MCP46X2 only) PSS -- 0.0015 0.0035 %/% 8-bit VDD = 2.7V to 5.5V, VA = 2.7V, Code = 80h -- 0.0015 0.0035 %/% 7-bit VDD = 2.7V to 5.5V, VA = 2.7V, Code = 40h Note 1: 2: 3: 4: 5: 6: 7: Resistance is defined as the resistance between terminal A to terminal B. INL and DNL are measured at VW with VA = VDD and VB = VSS. MCP4XX1 only. MCP4XX2 only, includes VWZSE and VWFSE. Resistor terminals A, W and B's polarity with respect to each other is not restricted. This specification by design. Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification DS22096A-page 12 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X SCL 93 91 90 92 SDA STOP Condition START Condition I2C Bus Start/Stop Bits Timing Waveforms. FIGURE 1-1: I2C BUS START/STOP BITS REQUIREMENTS TABLE 1-1: I2C AC Characteristics Param. Symbol No. Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (Extended) Operating Voltage VDD range is described in AC/DC characteristics Characteristic FSCL D102 Cb Bus capacitive loading 90 TSU:STA START condition Setup time 91 THD:STA START condition Hold time 92 TSU:STO STOP condition Setup time 93 THD:STO STOP condition Hold time (c) 2008 Microchip Technology Inc. Standard Mode Fast Mode High-Speed 1.7 High-Speed 3.4 100 kHz mode 400 kHz mode 1.7 MHz mode 3.4 MHz mode 100 kHz mode 400 kHz mode 1.7 MHz mode 3.4 MHz mode 100 kHz mode 400 kHz mode 1.7 MHz mode 3.4 MHz mode 100 kHz mode 400 kHz mode 1.7 MHz mode 3.4 MHz mode 100 kHz mode 400 kHz mode 1.7 MHz mode 3.4 MHz mode Min Max Units 0 0 0 0 -- -- -- -- 4700 600 160 160 4000 600 160 160 4000 600 160 160 4000 600 160 160 100 400 1.7 3.4 400 400 400 100 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- kHz kHz MHz MHz pF pF pF pF ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Conditions Cb = 400 pF, 1.8V - 5.5V Cb = 400 pF, 2.7V - 5.5V Cb = 400 pF, 4.5V - 5.5V Cb = 100 pF, 4.5V - 5.5V Only relevant for repeated START condition After this period the first clock pulse is generated DS22096A-page 13 MCP453X/455X/463X/465X 103 102 100 101 SCL 90 106 91 92 107 SDA In 110 109 109 SDA Out I2C Bus Data Timing. FIGURE 1-2: I2C BUS DATA REQUIREMENTS (SLAVE MODE) TABLE 1-2: I2C AC Characteristics Param. No. Sym Characteristic 100 THIGH Clock high time 101 Note 1: 2: 3: 4: 5: 6: 7: TLOW Clock low time Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (Extended) Operating Voltage VDD range is described in AC/DC characteristics Min Max Units 100 kHz mode 4000 -- ns 1.8V-5.5V 400 kHz mode 600 -- ns 2.7V-5.5V 1.7 MHz mode 120 ns 4.5V-5.5V 3.4 MHz mode 60 -- ns 4.5V-5.5V 100 kHz mode 4700 -- ns 1.8V-5.5V 400 kHz mode 1300 -- ns 2.7V-5.5V ns 4.5V-5.5V -- ns 4.5V-5.5V 1.7 MHz mode 320 3.4 MHz mode 160 Conditions As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the requirement tSU;DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line TR max.+tSU;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before the SCL line is released. The MCP46X1/MCP46X2 device must provide a data hold time to bridge the undefined part between VIH and VIL of the falling edge of the SCL signal. This specification is not a part of the I2C specification, but must be tested in order to ensure that the output data will meet the setup and hold specifications for the receiving device. Use Cb in pF for the calculations. Not Tested A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do not unintentionally create a Start or Stop condition. Ensured by the TAA 3.4 MHz specification test. DS22096A-page 14 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X TABLE 1-2: I2C BUS DATA REQUIREMENTS (SLAVE MODE) (CONTINUED) I2C AC Characteristics Param. No. Sym 102A (5) TRSCL 102B (5) 103A 103B (5) (5) 106 Note 1: 2: 3: 4: 5: 6: 7: TRSDA TFSCL TFSDA THD:DAT Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (Extended) Operating Voltage VDD range is described in AC/DC characteristics Characteristic SCL rise time SDA rise time SCL fall time SDA fall time Data input hold time Min Max Units Conditions 100 kHz mode -- 400 kHz mode 20 + 0.1Cb 1000 ns 300 ns Cb is specified to be from 10 to 400 pF (100 pF maximum for 3.4 MHz mode) 1.7 MHz mode 20 80 ns 1.7 MHz mode 20 160 ns 3.4 MHz mode 10 40 ns 3.4 MHz mode 10 80 ns After a Repeated Start condition or an Acknowledge bit 100 kHz mode -- 1000 ns Cb is specified to be from 10 to 400 pF (100 pF max for 3.4 MHz mode) 400 kHz mode 20 + 0.1Cb 300 ns 1.7 MHz mode 20 160 ns 3.4 MHz mode 10 80 ns 100 kHz mode -- 300 ns 400 kHz mode 20 + 0.1Cb 300 ns 1.7 MHz mode 20 80 ns 3.4 MHz mode 10 40 ns 100 kHz mode -- 300 ns 400 kHz mode 20 + 0.1Cb (4) 300 ns 1.7 MHz mode 20 160 ns 3.4 MHz mode 10 80 ns After a Repeated Start condition or an Acknowledge bit Cb is specified to be from 10 to 400 pF (100 pF max for 3.4 MHz mode) Cb is specified to be from 10 to 400 pF (100 pF max for 3.4 MHz mode) 100 kHz mode 0 -- ns 1.8V-5.5V, Note 6 400 kHz mode 0 -- ns 2.7V-5.5V, Note 6 1.7 MHz mode 0 -- ns 4.5V-5.5V, Note 6 3.4 MHz mode 0 -- ns 4.5V-5.5V, Note 6 As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the requirement tSU;DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line TR max.+tSU;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before the SCL line is released. The MCP46X1/MCP46X2 device must provide a data hold time to bridge the undefined part between VIH and VIL of the falling edge of the SCL signal. This specification is not a part of the I2C specification, but must be tested in order to ensure that the output data will meet the setup and hold specifications for the receiving device. Use Cb in pF for the calculations. Not Tested A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do not unintentionally create a Start or Stop condition. Ensured by the TAA 3.4 MHz specification test. (c) 2008 Microchip Technology Inc. DS22096A-page 15 MCP453X/455X/463X/465X I2C BUS DATA REQUIREMENTS (SLAVE MODE) (CONTINUED) TABLE 1-2: I2C AC Characteristics Param. No. 107 109 110 Sym 2: 3: 4: 5: 6: 7: Characteristic TSU:DAT Data input setup time TAA TBUF TSP Note 1: Standard Operating Conditions (unless otherwise specified) Operating Temperature -40C TA +125C (Extended) Operating Voltage VDD range is described in AC/DC characteristics Output valid from clock Bus free time Input filter spike suppression (SDA and SCL) Min Max Units Conditions 100 kHz mode 250 -- ns 400 kHz mode 100 -- ns Note 2 1.7 MHz mode 10 -- ns 3.4 MHz mode 10 -- ns 100 kHz mode -- 3450 ns 400 kHz mode -- 900 ns 1.7 MHz mode -- 150 ns Cb = 100 pF, Note 1, Note 7 -- 310 ns Cb = 400 pF, Note 1, Note 5 3.4 MHz mode -- 150 ns Cb = 100 pF, Note 1 100 kHz mode 4700 -- ns Time the bus must be free before a new transmission can start Note 1 400 kHz mode 1300 -- ns 1.7 MHz mode N.A. -- ns 3.4 MHz mode N.A. -- ns 100 kHz mode -- 50 ns 400 kHz mode -- 50 ns 1.7 MHz mode -- 10 ns Spike suppression 3.4 MHz mode -- 10 ns Spike suppression Philips Spec states N.A. As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the requirement tSU;DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line TR max.+tSU;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before the SCL line is released. The MCP46X1/MCP46X2 device must provide a data hold time to bridge the undefined part between VIH and VIL of the falling edge of the SCL signal. This specification is not a part of the I2C specification, but must be tested in order to ensure that the output data will meet the setup and hold specifications for the receiving device. Use Cb in pF for the calculations. Not Tested A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do not unintentionally create a Start or Stop condition. Ensured by the TAA 3.4 MHz specification test. DS22096A-page 16 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, VDD = +2.7V to +5.5V, VSS = GND. Parameters Sym Min Typ Max Units Specified Temperature Range TA -40 -- +125 C Operating Temperature Range TA -40 -- +125 C Storage Temperature Range TA -65 -- +150 C Thermal Resistance, 8L-DFN (3x3) JA -- 60 -- C/W Thermal Resistance, 8L-MSOP JA -- 211 -- C/W Thermal Resistance, 8L-SOIC JA -- 145.5 -- C/W Thermal Resistance, 10L-DFN (3x3) JA -- 57 -- C/W Thermal Resistance, 10L-MSOP JA -- 202 -- C/W Thermal Resistance, 14L-MSOP JA -- N/A -- C/W Thermal Resistance, 14L-SOIC JA -- 95.3 -- C/W Thermal Resistance, 16L-QFN JA -- 47 -- C/W Conditions Temperature Ranges Thermal Package Resistances (c) 2008 Microchip Technology Inc. DS22096A-page 17 MCP453X/455X/463X/465X NOTES: DS22096A-page 18 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 250 450 1000 800 600 400 200 0 -200 -400 -600 -800 -1000 3.4MHz, 5.5V 400 200 3.4MHz, 2.7V 1.7MHz, 5.5V IDD (uA) 300 250 1.7MHz, 2.7V 200 400kHz, 5.5V 100kHz, 5.5V 150 100 400kHz, 2.7V 50 RHVC (kOhms) 350 0 40 100 50 100kHz, 2.7V RHVC 0 -40 IHVC 150 80 0 120 2 3 4 5 Temperature (C) FIGURE 2-1: Device Current (IDD) vs. I2C Frequency (fSCL) and Ambient Temperature (VDD = 2.7V and 5.5V). 8 9 10 FIGURE 2-4: HVC Pull-up/Pull-down Resistance (RHVC) and Current (IHVC) vs. HVC Input Voltage (VHVC) (VDD = 5.5V). 12 HVC VPP Threshold (V) 3 2.5 Istandby (uA) 6 7 VHVC (V) IHVC (A) Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 5.5V 2 1.5 1 2.7V 0.5 10 5.5V Entry 8 2.7V Entry 5.5V Exit 6 4 2.7V Exit 2 0 -40 0 40 80 120 Temperature (C) FIGURE 2-2: Device Current (ISHDN) and VDD. (HVC = VDD) vs. Ambient Temperature. -40 -20 0 20 40 60 80 Ambient Temperature (C) 100 120 FIGURE 2-5: HVC High Input Entry/Exit Threshold vs. Ambient Temperature and VDD. 420 IWRITE (A) 400 380 360 5.5V 340 320 300 -40 0 40 80 120 Temperature (C) FIGURE 2-3: Write Current (IWRITE) vs. Ambient Temperature. (c) 2008 Microchip Technology Inc. DS22096A-page 19 MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 80 0 60 -0.1 40 20 0 -0.2 RW -0.3 64 96 128 160 192 224 256 Wiper Setting (decimal) 32 -40C Rw -40C INL -40C DNL 260 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL INL 220 0.1 180 0 140 -0.1 RW 100 125C 60 -40C 20 0 32 25C -0.2 85C 2000 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL 0.5 0.2 1500 0.1 0 1000 -0.1 DNL RW 0 Note: 64 128 192 Wiper Setting (decimal) -0.2 FIGURE 2-8: 5 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 1.8V). -0.75 RW -1.25 64 96 128 160 192 224 256 Wiper Setting (decimal) -40C Rw -40C INL -40C DNL 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL 6 INL 4 2 140 RW 100 0 -40C 60 125C 20 0 32 85C 25C DNL -2 64 96 128 160 192 224 256 Wiper Setting (decimal) FIGURE 2-10: 5 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 3.0V). -40C Rw -40C INL -40C DNL 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL 118 98 INL 78 1500 58 1000 38 500 RW 18 DNL 0 256 Refer to AN1080 for additional information on the characteristics of the wiper resistance (RW) with respect to device voltage and wiper setting value. DS22096A-page 20 32 DNL -40C 180 -0.3 0 85C 25C 2000 0.3 INL 500 125C 2500 0.4 Error (LSb) Wiper Resistance (RW) (ohms) -40C Rw -40C INL -40C DNL 40 FIGURE 2-9: 5 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 5.5V). -0.3 64 96 128 160 192 224 256 Wiper Setting (decimal) FIGURE 2-7: 5 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 3.0V). 2500 -0.25 220 DNL 0.75 60 260 0.2 1.25 0.25 300 0.3 125C Rw 125C INL 125C DNL Error (LSb) Wiper Resistance (R W) (ohms) 300 125C Rw 125C INL 125C DNL 80 0 FIGURE 2-6: 5 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 5.5V). 85C Rw 85C INL 85C DNL INL 20 Wiper Resistance (R W) (ohms) 125C -40C 25C 85C 100 25C Rw 25C INL 25C DNL Error (LSb) 0.1 -40C Rw -40C INL -40C DNL Error (LSb) 0.2 INL DNL 120 0.3 125C Rw 125C INL 125C DNL -2 0 Note: Error (LSb) 85C Rw 85C INL 85C DNL Wiper Resistance (RW) (ohms) 100 25C Rw 25C INL 25C DNL Wiper Resistance (R W) (ohms) -40C Rw -40C INL -40C DNL Error (LSb) Wiper Resistance (R W) (ohms) 120 64 128 192 Wiper Setting (decimal) 256 Refer to AN1080 for additional information on the characteristics of the wiper resistance (RW) with respect to device voltage and wiper setting value. FIGURE 2-11: 5 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 1.8V). (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 5300 6000 5250 5000 RWB (Ohms) Nominal Resistance (R AB) (Ohms) Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 2.7V 5200 5150 5100 4000 3000 2000 -40C 25C 85C 125C 1000 5.5V 5050 0 -40 0 40 80 Ambient Temperature (C) 120 FIGURE 2-12: 5 k - Nominal Resistance () vs. Ambient Temperature and VDD. (c) 2008 Microchip Technology Inc. 0 32 64 96 128 160 192 Wiper Setting (decimal) 224 256 FIGURE 2-13: 5 k - RWB () vs. Wiper Setting and Ambient Temperature. DS22096A-page 21 MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. FIGURE 2-14: 5 k - Low-Voltage Decrement Wiper Settling Time (VDD = 5.5V) (1 s/Div). FIGURE 2-17: 5 k - Low-Voltage Increment Wiper Settling Time (VDD = 5.5V) (1 s/Div). FIGURE 2-15: 5 k - Low-Voltage Decrement Wiper Settling Time (VDD = 2.7V) (1 s/Div). FIGURE 2-18: 5 k - Low-Voltage Increment Wiper Settling Time (VDD = 2.7V) (1 s/Div). FIGURE 2-16: 5 k - Power-Up Wiper Response Time (20 ms/Div). DS22096A-page 22 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 0.1 80 0 60 -0.1 25C -40C 125C 85C 100 -0.2 RW 20 -0.3 -40C Rw -40C INL -40C DNL 260 220 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL INL DNL 0.1 0 140 100 -0.1 RW 25C 125C 85C 20 0 32 -0.2 -40C 3500 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 3000 2500 125C Rw 125C INL 125C DNL 0.5 INL 0.3 0.4 0.2 2000 DNL 0.1 1500 0 1000 -0.1 500 RW 0 0 64 128 192 Wiper Setting (decimal) -0.2 FIGURE 2-21: 10 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 1.8V). (c) 2008 Microchip Technology Inc. 260 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL -0.5 DNL 4 125C Rw 125C INL 125C DNL 3 INL 220 2 180 1 140 0 100 -40C 60 DNL RW -1 -2 0 25 50 75 100 125 150 175 200 225 250 Wiper Setting (decimal) FIGURE 2-23: 10 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 3.0V). -40C Rw -40C INL -40C DNL 3500 25C Rw 25C INL 25C DNL 3000 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL INL 2500 2000 1500 1000 500 -0.3 256 Refer to AN1080 for additional information on the characteristics of the wiper resistance (RW) with respect to device voltage and wiper setting value. RW -40C -1 64 96 128 160 192 224 256 Wiper Setting (decimal) -40C Rw -40C INL -40C DNL 4000 Error (LSb) -40C Rw -40C INL -40C DNL 32 85C 25C 20 0.6 4000 Wiper Resistance (R W)(ohms) 125C 125C 85C 25C -0.3 64 96 128 160 192 224 256 Wiper Setting (decimal) FIGURE 2-20: 10 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 3.0V). Note: 40 300 0.2 180 60 0 60 FIGURE 2-22: 10 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 5.5V). 0.3 125C Rw 125C INL 125C DNL 1 125C Rw 125C INL 125C DNL 80 0 Error (LSb) Wiper Resistance (R W) (ohms) 300 85C Rw 85C INL 85C DNL 0.5 20 FIGURE 2-19: 10 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 5.5V). 25C Rw 25C INL 25C DNL INL 25 50 75 100 125 150 175 200 225 250 Wiper Setting (decimal) Wiper Resistance (R W) (ohms) 0 Wiper Resistance (RW) (ohms) 40 -40C Rw -40C INL -40C DNL Error (LSb) 0.2 INL DNL 120 0.3 125C Rw 125C INL 125C DNL Error (LSb) 85C Rw 85C INL 85C DNL RW DNL 0 0 Note: 64 128 192 Wiper Setting (decimal) 98 88 78 68 58 48 38 28 18 8 -2 Error (LSb) 100 25C Rw 25C INL 25C DNL Wiper Resistance (R W) (ohms) -40C Rw -40C INL -40C DNL Error (LSb) Wiper Resistance (R W) (ohms) 120 256 Refer to AN1080 for additional information on the characteristics of the wiper resistance (RW) with respect to device voltage and wiper setting value. FIGURE 2-24: 10 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 1.8V). DS22096A-page 23 MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 12000 AB) 10250 Nominal Resistance (R (Ohms) 10300 10200 10000 10100 RWB (Ohms) 10150 2.7V 10050 10000 5.5V 9950 1.8V 8000 6000 4000 -40C 25C 85C 125C 2000 9900 9850 0 -40 0 40 80 Ambient Temperature (C) 120 FIGURE 2-25: 10 k - Nominal Resistance () vs. Ambient Temperature and VDD. DS22096A-page 24 0 32 64 96 128 160 192 Wiper Setting (decimal) 224 256 FIGURE 2-26: 10 k - RWB () vs. Wiper Setting and Ambient Temperature. (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. FIGURE 2-27: 10 k - Low-Voltage Decrement Wiper Settling Time (VDD = 5.5V) (1 s/Div). FIGURE 2-30: 10 k - Low-Voltage Increment Wiper Settling Time (VDD = 5.5V) (1 s/Div). FIGURE 2-28: 10 k - Low-Voltage Decrement Wiper Settling Time (VDD = 2.7V) (1 s/Div). FIGURE 2-31: 10 k - Low-Voltage Increment Wiper Settling Time (VDD = 2.7V) (1 s/Div). FIGURE 2-29: 10 k - Power-Up Wiper Response Time (1 s/Div). (c) 2008 Microchip Technology Inc. DS22096A-page 25 MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 0 60 -0.1 40 25C 85C 125C 20 0 -40C 100 -0.2 RW -0.3 64 96 128 160 192 224 256 Wiper Setting (decimal) 32 -40C Rw -40C INL -40C DNL 260 220 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 0.1 180 0 140 -0.2 -40C 60 32 15000 14000 13000 12000 11000 10000 9000 8000 7000 6000 5000 4000 3000 2000 1000 0 -40C Rw -40C INL -40C DNL 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 256 125C Rw 125C INL 125C DNL Error (LSb) INL RW 64 128 192 Wiper Setting (decimal) Refer to AN1080 for additional information on the characteristics of the wiper resistance (RW) with respect to device voltage and wiper setting value. FIGURE 2-34: 50 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 1.8V). DS22096A-page 26 32 RW -0.2 -0.3 64 96 128 160 192 224 256 Wiper Setting (decimal) -40C Rw -40C INL -40C DNL 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL INL 1 0.75 0.5 DNL 0.25 0 -0.25 RW 100 -0.5 -40C 60 125C DNL 0 85C 25C 125C 140 -0.3 64 96 128 160 192 224 256 Wiper Setting (decimal) FIGURE 2-33: 50 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 3.0V). -40C 180 0 32 -0.75 85C 25C 20 64 -1 96 128 160 192 224 256 Wiper Setting (decimal) FIGURE 2-36: 50 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 3.0V). Wiper Resistance (Rw) (ohms) 0 Wiper Resistance (RW) (ohms) -0.1 40 125C 85C 25C 20 Note: 0 260 -0.1 RW 100 0.1 60 220 INL DNL DNL 300 0.2 0.2 FIGURE 2-35: 50 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 5.5V). 0.3 125C Rw 125C INL 125C DNL 0.3 125C Rw 125C INL 125C DNL 80 0 Error (LSb) Wiper Resistance (R W) (ohms) 300 85C Rw 85C INL 85C DNL INL 20 FIGURE 2-32: 50 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 5.5V). 25C Rw 25C INL 25C DNL Error (LSb) 0.1 80 -40C Rw -40C INL -40C DNL Error (LSb) 0.2 INL DNL 120 0.3 125C Rw 125C INL 125C DNL 15000 14000 13000 12000 11000 10000 9000 8000 7000 6000 5000 4000 3000 2000 1000 0 -40C Rw -40C INL -40C DNL 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL RW INL DNL 78.5 73.5 68.5 63.5 58.5 53.5 48.5 43.5 38.5 33.5 28.5 23.5 18.5 13.5 8.5 3.5 -1.5 Error (LSb) 85C Rw 85C INL 85C DNL Wiper Resistance (R W) (ohms) 100 25C Rw 25C INL 25C DNL Wiper Resistance (R W) (ohms) -40C Rw -40C INL -40C DNL Error (LSb) Wiper Resistance (R W) (ohms) 120 0 25 50 75 100 125 150 175 200 225 250 Wiper Setting (decimal) Note: Refer to AN1080 for additional information on the characteristics of the wiper resistance (RW) with respect to device voltage and wiper setting value. FIGURE 2-37: 50 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 1.8V). (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 60000 52000 50000 51500 1.8V RWB (Ohms) Nominal Resistance (R (Ohms) AB) 52500 51000 50500 50000 2.7V 40000 30000 20000 -40C 25C 85C 125C 10000 49500 5.5V 49000 0 -40 0 40 80 Ambient Temperature (C) 120 FIGURE 2-38: 50 k - Nominal Resistance () vs. Ambient Temperature and VDD. (c) 2008 Microchip Technology Inc. 0 32 64 96 128 160 192 Wiper Setting (decimal) 224 256 FIGURE 2-39: 50 k - RWB () vs. Wiper Setting and Ambient Temperature. DS22096A-page 27 MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. FIGURE 2-40: 50 k - Low-Voltage Decrement Wiper Settling Time (VDD = 5.5V) (1 s/Div). FIGURE 2-43: 50 k - Low-Voltage Increment Wiper Settling Time (VDD = 5.5V) (1 s/Div). FIGURE 2-41: 50 k - Low-Voltage Decrement Wiper Settling Time (VDD = 2.7V) (1 s/Div). FIGURE 2-44: 50 k - Low-Voltage Increment Wiper Settling Time (VDD = 2.7V) (1 s/Div). FIGURE 2-42: 50 k - Power-Up Wiper Response Time (1 s/Div). DS22096A-page 28 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 0 60 -0.1 40 25C -40C RW -0.2 64 96 128 160 192 224 256 Wiper Setting (decimal) -40C Rw -40C INL -40C DNL 260 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL -0.1 40 -40C 220 DNL 260 0 140 -0.05 100 RW 60 -0.1 -40C -0.15 125C 85C 25C 20 0 32 25000 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 0.05 15000 -0.05 10000 -0.15 5000 RW INL 0 64 128 192 Wiper Setting (decimal) 0.2 0 -0.2 RW 100 60 -0.4 -40C 125C 85C 25C 32 -0.6 64 96 128 160 192 224 256 Wiper Setting (decimal) FIGURE 2-49: 100 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 3.0V). -40C Rw -40C INL -40C DNL 25000 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL RW 20000 INL 15000 10000 5000 DNL 0 256 Refer to AN1080 for additional information on the characteristics of the wiper resistance (RW) with respect to device voltage and wiper setting value. FIGURE 2-47: 100 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 1.8V). (c) 2008 Microchip Technology Inc. 0.4 140 -0.35 0 Note: -0.25 0.6 125C Rw 125C INL 125C DNL DNL 0 0.25 85C Rw 85C INL 85C DNL 180 0.35 0.15 DNL 20000 125C Rw 125C INL 125C DNL 25C Rw 25C INL 25C DNL INL 20 Error (LSb) Wiper Resistance (RW) (ohms) -40C Rw -40C INL -40C DNL -0.3 64 96 128 160 192 224 256 Wiper Setting (decimal) -40C Rw -40C INL -40C DNL 220 -0.2 64 96 128 160 192 224 256 Wiper Setting (decimal) FIGURE 2-46: 100 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 3.0V). 32 -0.2 FIGURE 2-48: 100 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 5.5V). 0.15 0.05 180 RW 125C 85C 25C 300 0.1 INL 0.1 0 0.2 Error (LSb) Wiper Resistance (R W) (ohms) 300 0.2 60 0 FIGURE 2-45: 100 k Pot Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 5.5V). 0.3 125C Rw 125C INL 125C DNL DNL 80 20 Wiper Resistance (Rw) (ohms) 32 Wiper Resistance (RW) (ohms) 0 85C Rw 85C INL 85C DNL INL 125C 85C 20 25C Rw 25C INL 25C DNL Error (LSb) DNL -40C Rw -40C INL -40C DNL 100 0.1 INL 80 120 0.2 125C Rw 125C INL 125C DNL Error (LSb) 85C Rw 85C INL 85C DNL 0 Note: 64 128 192 Wiper Setting (decimal) 59 54 49 44 39 34 29 24 19 14 9 4 -1 Error (LSb) 100 25C Rw 25C INL 25C DNL Wiper Resistance (R W) (ohms) -40C Rw -40C INL -40C DNL Error (LSb) Wiper Resistance (R W) (ohms) 120 256 Refer to AN1080 for additional information on the characteristics of the wiper resistance (RW) with respect to device voltage and wiper setting value. FIGURE 2-50: 100 k Rheo Mode - RW (), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 1.8V). DS22096A-page 29 MCP453X/455X/463X/465X 120000 103500 103000 102500 102000 101500 101000 100500 100000 99500 99000 98500 100000 Rwb (Ohms) Nominal Resistance (R (Ohms) AB) Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 1.8V 2.7V 80000 60000 40000 -40C 25C 85C 125C 20000 5.5V 0 -40 0 40 80 Ambient Temperature (C) 120 FIGURE 2-51: 100 k - Nominal Resistance () vs. Ambient Temperature and VDD . DS22096A-page 30 0 32 64 96 128 160 192 Wiper Setting (decimal) 224 256 FIGURE 2-52: 100 k - RWB () vs. Wiper Setting and Ambient Temperature. (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. FIGURE 2-53: 100 k - Low-Voltage Decrement Wiper Settling Time (VDD = 5.5V) (1 s/Div). FIGURE 2-55: 100 k - Low-Voltage Increment Wiper Settling Time (VDD =5.5V) (1 s/Div). FIGURE 2-54: 100 k - Low-Voltage Decrement Wiper Settling Time (VDD = 2.7V) (1 s/Div). FIGURE 2-56: 100 k - Low-Voltage Increment Wiper Settling Time (VDD = 2.7V) (1 s/Div) (c) 2008 Microchip Technology Inc. DS22096A-page 31 MCP453X/455X/463X/465X 0.12 0.1 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 0.1 0.08 5.5V % % Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 0.06 0.04 3.0V 0.02 3.0V 0 -40 0 40 80 Temperature (C) 120 FIGURE 2-57: Resistor Network 0 to Resistor Network 1 RAB (5 k) Mismatch vs. VDD and Temperature. -40 0.04 0.05 0.03 0.04 40 80 Temperature (C) 0.03 5.5V 0.01 0 120 FIGURE 2-59: Resistor Network 0 to Resistor Network 1 RAB (50 k) Mismatch vs. VDD and Temperature. 0.02 5.5V 0.02 0 % % 5.5V -0.01 3.0V 0 3.0V -0.02 0.01 -0.01 -0.03 -0.02 -0.04 -0.03 -40 0 40 80 Temperature (C) 120 FIGURE 2-58: Resistor Network 0 to Resistor Network 1 RAB (10 k) Mismatch vs. VDD and Temperature. DS22096A-page 32 -40 10 60 Temperature (C) 110 FIGURE 2-60: Resistor Network 0 to Resistor Network 1 RAB (100 k) Mismatch vs. VDD and Temperature. (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. 4 230 210 3.5 VOL (mV) VIH (V) 3 2.5 2 2.7V 190 5.5V 2.7V 170 150 130 5.5V 110 90 1.5 70 50 1 -40 0 40 80 120 Temperature (C) FIGURE 2-61: Temperature. -40 0 40 80 120 Temperature (C) VIH (SDA, SCL) vs. VDD and FIGURE 2-63: VOL (SDA) vs. VDD and Temperature (IOL = 3 mA). 2 VIL (V) 5.5V 1.5 2.7V 1 -40 0 40 80 120 Temperature (C) FIGURE 2-62: Temperature. VIL (SDA, SCL) vs. VDD and (c) 2008 Microchip Technology Inc. DS22096A-page 33 MCP453X/455X/463X/465X 2.1 Note: Unless otherwise indicated, TA = +25C, VDD = 5V, VSS = 0V. Test Circuits 1.2 +5V 1 5.5V VIN VDD (V) 0.8 0.6 2.7V Offset GND 0.4 0.2 A W B + VOUT - 2.5V DC 0 -40 0 40 80 120 Temperature (C) FIGURE 2-64: and Temperature. DS22096A-page 34 POR/BOR Trip point vs. VDD FIGURE 2-65: Test. -3 db Gain vs. Frequency (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3-1. Additional descriptions of the device pins follows. TABLE 3-1: PINOUT DESCRIPTION FOR THE MCP453X/455X/463X/465X Pin Single Dual Rheo Pot (1) Rheo Pot Symbol I/O Buffer Type Weak Pull-up/ down (1) Standard Function 8L 8L 10L 14L 16L 1 1 1 1 16 HVC/A0 I HV w/ST "smart" 2 2 2 2 1 SCL I HV w/ST No I2C clock input. 3 3 3 3 2 SDA I/O HV w/ST No I2C serial data I/O. Open Drain output 4 4 4 4 3, 4 VSS -- P -- Ground -- -- 5 5 5 P1B A Analog No Potentiometer 1 Terminal B -- -- 6 6 6 P1W A Analog No Potentiometer 1 Wiper Terminal -- -- -- 7 7 P1A A Analog No Potentiometer 1 Terminal A -- 5 -- 8 8 P0A A Analog No Potentiometer 0 Terminal A 5 6 7 9 9 P0W A Analog No Potentiometer 0 Wiper Terminal 6 7 8 10 10 P0B A Analog No Potentiometer 0 Terminal B -- -- -- 11 11, 12 NC -- -- -- No Connection -- -- -- 12 13 A2 I HV w/ST "smart" Address 2 7 -- 9 13 14 A1 I HV w/ST "smart" Address 1 8 8 10 14 15 VDD -- P -- Positive Power Supply Input 9 9 11 -- 17 EP -- -- -- Exposed Pad (Note 2) Legend: Note 1: 2: High Voltage Command / Address 0. HV w/ST = High Voltage tolerant input (with Schmidtt trigger input) A = Analog pins (Potentiometer terminals) I = digital input (high Z) O = digital output I/O = Input / Output P = Power The pin's "smart" pull-up shuts off while the pin is forced low. This is done to reduce the standby and shutdown current. The DFN and QFN packages have a contact on the bottom of the package. This contact is conductively connected to the die substrate, and therefore should be unconnected or connected to the same ground as the device's VSS pin. (c) 2008 Microchip Technology Inc. DS22096A-page 35 MCP453X/455X/463X/465X 3.1 High Voltage Command / Address 0 (HVC/A0) The HVC/A0 pin is the Address 0 input for the I2C interface as well as the High Voltage Command pin. At the device's POR/BOR the value of the A0 address bit is latched. This input along with the A2 and A1 pins completes the device address. This allows up to 8 MCP45xx/46xx devices can be on a single I2C bus. During normal operation the the voltage on this pin determines if the I2C command is a normal command or a High Voltage command (when HVC/A0 = VIHH). 3.2 Serial Clock (SCL) The SCL pin is the serial interfaces Serial Clock pin. This pin is connected to the Host Controllers SCL pin. The MCP45XX/46XX is a slave device, so it's SCL pin accepts only external clock signals. 3.3 Serial Data (SDA) The SDA pin is the serial interfaces Serial Data pin. This pin is connected to the Host Controllers SDA pin. The SDA pin is an open-drain N-channel driver. 3.4 Ground (VSS) The VSS pin is the device ground reference. 3.5 Potentiometer Terminal A The terminal A pin is available on the MCP4XX1 devices, and is connected to the internal potentiometer's terminal A. The potentiometer's terminal A is the fixed connection to the Full-Scale wiper value of the digital potentiometer. This corresponds to a wiper value of 0x100 for 8-bit devices or 0x80 for 7-bit devices. The terminal A pin does not have a polarity relative to the terminal W or B pins. The terminal A pin can support both positive and negative current. The voltage on terminal A must be between VSS and VDD. The terminal A pin is not available on the MCP4XX2 devices, and the internally terminal A signal is floating. MCP46X1 devices have two terminal A pins, one for each resistor network. 3.8 Address 2 (A2) The A2 pin is the I2C interface's Address 2 pin. Along with the A1 and A0 pins, up to 8 MCP45XX/46XX devices can be on a single I2C bus. 3.9 Address 1 (A1) The A2 pin is the I2C interface's Address 1 pin. Along with the A2 and A0 pins, up to 8 MCP45XX/46XX devices can be on a single I2C bus. Potentiometer Terminal B The terminal B pin is connected to the internal potentiometer's terminal B. The potentiometer's terminal B is the fixed connection to the Zero Scale wiper value of the digital potentiometer. This corresponds to a wiper value of 0x00 for both 7-bit and 8-bit devices. The terminal B pin does not have a polarity relative to the terminal W or A pins. The terminal B pin can support both positive and negative current. The voltage on terminal B must be between VSS and VDD. MCP46XX devices have two terminal B pins, one for each resistor network. 3.6 3.7 Potentiometer Wiper (W) Terminal The terminal W pin is connected to the internal potentiometer's terminal W (the wiper). The wiper terminal is the adjustable terminal of the digital potentiometer. The terminal W pin does not have a polarity relative to terminals A or B pins. The terminal W pin can support both positive and negative current. The voltage on terminal W must be between VSS and VDD. 3.10 Positive Power Supply Input (VDD) The VDD pin is the device's positive power supply input. The input power supply is relative to VSS. While the device VDD < Vmin (2.7V), the electrical performance of the device may not meet the data sheet specifications. 3.11 No Connect (NC) These pins should be either connected to VDD or VSS. 3.12 Exposed Pad (EP) This pad is conductively connected to the device's substrate. This pad should be tied to the same potential as the VSS pin (or left unconnected). This pad could be used to assist as a heat sink for the device when connected to a PCB heat sink. MCP46XX devices have two terminal W pins, one for each resistor network. DS22096A-page 36 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 4.0 FUNCTIONAL OVERVIEW This Data Sheet covers a family of thirty-two Digital Potentiometer and Rheostat devices that will be referred to as MCP4XXX. The MCP4XX1 devices are the Potentiometer configuration, while the MCP4XX2 devices are the Rheostat configuration. As the Device Block Diagram shows, there are four main functional blocks. These are: * * * * POR/BOR Operation Memory Map Resistor Network Serial Interface (I2C) The POR/BOR operation and the Memory Map are discussed in this section and the Resistor Network and I2C operation are described in their own sections. The Device Commands commands are discussed in Section 7.0 "Device Commands". 4.1 POR/BOR Operation The Power-on Reset is the case where the device is having power applied to it starting from the VSS level. The Brown-out Reset occurs when a device had power applied to it, and that power (voltage) drops below the specified range. The devices RAM retention voltage (VRAM) is lower than the POR/BOR voltage trip point (VPOR/VBOR). The maximum VPOR/VBOR voltage is less than 1.8V. When VPOR/VBOR < VDD < 2.7V, the electrical performance may not meet the data sheet specifications. In this region, the device is capable of incrementing, decrementing, reading and writing to its volatile memory if the proper serial command is executed. 4.1.1 POWER-ON RESET When the device powers up, the device VDD will cross the VPOR/VBOR voltage. Once the VDD voltage crosses the VPOR/VBOR voltage the following happens: * Volatile wiper register is loaded with value in the corresponding non-volatile wiper register * The TCON register is loaded it's default value * The device is capable of digital operation 4.1.2 BROWN-OUT RESET When the device powers down, the device VDD will cross the VPOR/VBOR voltage. Once the VDD voltage decreases below the VPOR/VBOR voltage the Serial Interface is disabled. If the VDD voltage decreases below the VRAM voltage the following happens: * Volatile wiper registers may become corrupted * TCON register may become corrupted As the voltage recovers above the VPOR/VBOR voltage see Section 4.1.1 "Power-on Reset". Serial commands not completed due to a brown-out condition may cause the volatile memory location to become corrupted. 4.2 Memory Map The device memory map supports 16 locations, of which 3 locations are used. Each location is 9-bits wide (16x9 bits). This memory space is shown in Table 4-1. TABLE 4-1: Address MEMORY MAP Function Memory Type 00h Volatile Wiper 0 RAM 01h Volatile Wiper 1 RAM 02h Reserved -- 03h Reserved -- 04h Volatile TCON Register RAM 05h Reserved RAM 06h - 0Fh Reserved 4.2.1 -- VOLATILE MEMORY (RAM) There are four Volatile Memory locations. These are: * Volatile Wiper 0 * Volatile Wiper 1 (Dual Resistor Network devices only) * Terminal Control (TCON) Register * Reserved The volatile memory starts functioning at the RAM retention voltage (VRAM). 4.2.1.1 Address 05h (Reserved) This memory location is Reserved and is mapped to the Status Register of the Non-Volatile MCP45XX/ 46XX devices. Since the Non-Volatile devices bits are not used by the volatile device, this location is reserved. Reading this address wil result in a value of 1F7h. (c) 2008 Microchip Technology Inc. DS22096A-page 37 MCP453X/455X/463X/465X 4.2.1.2 Terminal Control (TCON) Register This register contains 8 control bits. Four bits are for Wiper 0, and four bits are for Wiper 1. Register 4-1 describes each bit of the TCON register. The state of each resistor network terminal connection is individually controlled. That is, each terminal connection (A, B and W) can be individually connected/ disconnected from the resistor network. This allows the system to minimize the currents through the digital potentiometer. When the WL1 bit is enabled, writes to the TCON register bits R1HW, R1A, R1W, and R1B are inhibited. When the WL0 bit is enabled, writes to the TCON register bits R0HW, R0A, R0W, and R0B are inhibited. On a POR/BOR this register is loaded with 1FFh (9-bits), for all terminals connected. The Host Controller needs to detect the POR/BOR event and then update the Volatile TCON register value. Additionally, there is a bit which enables the operation of General Call commands. The value that is written to this register will appear on the resistor network terminals when the serial command has completed. DS22096A-page 38 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X REGISTER 4-1: TCON BITS (ADDRESS = 0x04) (1) R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 GCEN R1HW R1A R1W R1B R0HW R0A R0W R0B bit 8 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 8 GCEN: General Call Enable bit This bit specifies if I2C General Call commands are accepted 1 = Enable Device to "Accept" the General Call Address (0000h) 0 = The General Call Address is disabled bit 7 R1HW: Resistor 1 Hardware Configuration Control bit This bit forces Resistor 1 into the "shutdown" configuration of the Hardware pin 1 = Resistor 1 is NOT forced to the hardware pin "shutdown" configuration 0 = Resistor 1 is forced to the hardware pin "shutdown" configuration bit 6 R1A: Resistor 1 Terminal A (P1A pin) Connect Control bit This bit connects/disconnects the Resistor 1 Terminal A to the Resistor 1 Network 1 = P1A pin is connected to the Resistor 1 Network 0 = P1A pin is disconnected from the Resistor 1 Network bit 5 R1W: Resistor 1 Wiper (P1W pin) Connect Control bit This bit connects/disconnects the Resistor 1 Wiper to the Resistor 1 Network 1 = P1W pin is connected to the Resistor 1 Network 0 = P1W pin is disconnected from the Resistor 1 Network bit 4 R1B: Resistor 1 Terminal B (P1B pin) Connect Control bit This bit connects/disconnects the Resistor 1 Terminal B to the Resistor 1 Network 1 = P1B pin is connected to the Resistor 1 Network 0 = P1B pin is disconnected from the Resistor 1 Network bit 3 R0HW: Resistor 0 Hardware Configuration Control bit This bit forces Resistor 0 into the "shutdown" configuration of the Hardware pin 1 = Resistor 0 is NOT forced to the hardware pin "shutdown" configuration 0 = Resistor 0 is forced to the hardware pin "shutdown" configuration bit 2 R0A: Resistor 0 Terminal A (P0A pin) Connect Control bit This bit connects/disconnects the Resistor 0 Terminal A to the Resistor 0 Network 1 = P0A pin is connected to the Resistor 0 Network 0 = P0A pin is disconnected from the Resistor 0 Network bit 1 R0W: Resistor 0 Wiper (P0W pin) Connect Control bit This bit connects/disconnects the Resistor 0 Wiper to the Resistor 0 Network 1 = P0W pin is connected to the Resistor 0 Network 0 = P0W pin is disconnected from the Resistor 0 Network bit 0 R0B: Resistor 0 Terminal B (P0B pin) Connect Control bit This bit connects/disconnects the Resistor 0 Terminal B to the Resistor 0 Network 1 = P0B pin is connected to the Resistor 0 Network 0 = P0B pin is disconnected from the Resistor 0 Network Note 1: These bits do not affect the wiper register values. (c) 2008 Microchip Technology Inc. DS22096A-page 39 MCP453X/455X/463X/465X NOTES: DS22096A-page 40 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 5.0 RESISTOR NETWORK 5.1 The Resistor Network has either 7-bit or 8-bit resolution. Each Resistor Network allows zero scale to full-scale connections. Figure 5-1 shows a block diagram for the resistive network of a device. The Resistor Network is made up of several parts. These include: * Resistor Ladder * Wiper * Shutdown (Terminal Connections) Devices have either one or two resistor networks, These are referred to as Pot 0 and Pot 1. A RW RS RW R RAB S The resistor ladder is a series of equal value resistors (RS) with a connection point (tap) between the two resistors. The total number of resistors in the series (ladder) determines the RAB resistance (see Figure 5-1). The end points of the resistor ladder are connected to analog switches which are connected to the device Terminal A and Terminal B pins. The RAB (and RS) resistance has small variations over voltage and temperature. For an 8-bit device, there are 256 resistors in a string between terminal A and terminal B. The wiper can be set to tap onto any of these 256 resistors thus providing 257 possible settings (including terminal A and terminal B). 8-Bit N= 257 (1) (100h) 7-Bit N= 128 (80h) For a 7-bit device, there are 128 resistors in a string between terminal A and terminal B. The wiper can be set to tap onto any of these 128 resistors thus providing 129 possible settings (including terminal A and terminal B). 256 (FFh) 127 (7Fh) Equation 5-1 shows the calculation for the step resistance. 255 (FEh) 126 (7Eh) EQUATION 5-1: RW (1) RS Resistor Ladder Module (1) RS CALCULATION R AB R S = ------------( 256 ) 8-bit Device R AB R S = ------------( 128 ) 7-bit Device W RW RS RW 1 (1) (01h) 1 (01h) 0 (00h) 0 (00h) (1) Analog Mux B Note 1: The wiper resistance is dependent on several factors including, wiper code, device VDD, Terminal voltages (on A, B, and W), and temperature. Also for the same conditions, each tap selection resistance has a small variation. This RW variation has greater effects on some specifications (such as INL) for the smaller resistance devices (5.0 k) compared to larger resistance devices (100.0 k). FIGURE 5-1: Resistor Block Diagram. (c) 2008 Microchip Technology Inc. DS22096A-page 41 MCP453X/455X/463X/465X 5.2 Wiper TABLE 5-1: Each tap point (between the RS resistors) is a connection point for an analog switch. The opposite side of the analog switch is connected to a common signal which is connected to the Terminal W (Wiper) pin. A value in the volatile wiper register selects which analog switch to close, connecting the W terminal to the selected node of the resistor ladder. The wiper can connect directly to Terminal B or to Terminal A. A zero-scale connections, connects the Terminal W (wiper) to Terminal B (wiper setting of 000h). A full-scale connections, connects the Terminal W (wiper) to Terminal A (wiper setting of 100h or 80h). In these configurations the only resistance between the Terminal W and the other Terminal (A or B) is that of the analog switches. A wiper setting value greater than full-scale (wiper setting of 100h for 8-bit device or 80h for 7-bit devices) will also be a Full-Scale setting (Terminal W (wiper) connected to Terminal A). Table 5-1 illustrates the full wiper setting map. VOLATILE WIPER VALUE VS. WIPER POSITION MAP Wiper Setting Properties 7-bit Pot 8-bit Pot 3FFh 081h 3FFh 101h Reserved (Full-Scale (W = A)), Increment and Decrement commands ignored 080h 100h Full-Scale (W = A), Increment commands ignored 07Fh 041h 0FFh 081 W=N 040h 080h W = N (Mid-Scale) 03Fh 001h 07Fh 001 W=N 000h 000h Zero Scale (W = B) Decrement command ignored Equation 5-2 illustrates the calculation used to determine the resistance between the wiper and terminal B. EQUATION 5-2: RWB CALCULATION R AB N R WB = ------------- + RW ( 256 ) 8-bit Device N = 0 to 256 (decimal) R AB N - + RW R WB = ------------( 128 ) 7-bit Device N = 0 to 128 (decimal) DS22096A-page 42 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 5.3 Shutdown 5.3.2 Shutdown is used to minimize the device's current consumption. The MCP4XXX achieves this through the Terminal Control Register (TCON). 5.3.1 TERMINAL CONTROL REGISTER (TCON) The Terminal Control (TCON) register is a volatile register used to configure the connection of each resistor network terminal pin (A, B, and W) to the Resistor Network. This bits are described in Register 4-1. When the RxHW bit is a "0", the selected resistor network is forced into the following state: INTERACTION OF RxHW BIT AND RxA, RxW, AND RxB BITS (TCON REGISTER) Using the TCON bits allows each resistor network (Pot 0 and Pot 1) to be individually "shutdown". The state of the RxHW bit does NOT corrupt the other bit values in the TCON register nor the value of the Volatile Wiper Registers. When the Shutdown mode is exited (RxHW changes state from "0" to "1"): * The device returns to the Wiper setting specified by the Volatile Wiper value * The RxA, RxB, and RxW bits return to controlling the terminal connection state of that resistor network * The PxA terminal is disconnected * The PxW terminal is simultaneously connected to the PxB terminal (see Figure 5-2) * The Serial Interface is NOT disabled, and all Serial Interface activity is executed Alternate low power configurations may be achieved with the RxA, RxW, and RxB bits. Note 1: The RxHW bits are identical to the RxHW bits of the MCP41XX/42XX devices. The MCP42XX devices also have a SHDN pin which forces the resistor network into the same state as that resistor networks RxHW bit. 2: When RxHW = "0", the state of the TCON register RxA, RxW, and RxB bits is overridden (ignored). When the state of the RxHW bit returns to "1", the TCON register RxA, RxW, and RxB bits return to controlling the terminal connection state. In other words, the RxHW bit does not corrupt the state of the RxA, RxW, and RxB bits. Resistor Network A FIGURE 5-2: Configuration. W B Resistor Network Shutdown (c) 2008 Microchip Technology Inc. DS22096A-page 43 MCP453X/455X/463X/465X NOTES: DS22096A-page 44 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 6.0 SERIAL INTERFACE (I2C) 6.1 The MCP45XX/46XX devices support the I2C serial protocol. The MCP45XX/46XX I2C's module operates in Slave mode (does not generate the serial clock). Figure 6-1 shows a typical I2C Interface connection. All I2C interface signals are high-voltage tolerant. The MCP45XX/46XX devices use the two-wire I2C serial interface. This interface can operate in standard, fast or High-Speed mode. A device that sends data onto the bus is defined as transmitter, and a device receiving data as receiver. The bus has to be controlled by a master device which generates the serial clock (SCL), controls the bus access and generates the START and STOP conditions. The MCP45XX/46XX device works as slave. Both master and slave can operate as transmitter or receiver, but the master device determines which mode is activated. Communication is initiated by the master (microcontroller) which sends the START bit, followed by the slave address byte. The first byte transmitted is always the slave address byte, which contains the device code, the address bits, and the R/W bit. 2C Refer to the Phillips I the I2C specifications. document for more details of Typical I2C Interface Connections MCP4XXX Host Controller SCL SCL SDA SDA I/O (1) HVC/A0 (2) A1 (2, 3) A2 (2, 3) Note 1: If High voltage commands are desired, some type of external circuitry needs to be implemented. 2: These pins have internal pull-ups. If faster rise times are required, then external pull-ups should be added. 3: This pin could be tied high, low, or connected to an I/O pin of the Host Controller. FIGURE 6-1: Diagram. Typical I2C Interface Block Signal Descriptions The I2C interface uses up to five pins (signals). These are: * * * * * SDA (Serial Data) SCL (Serial Clock) A0 (Address 0 bit) A1 (Address 1 bit) A2 (Address 2 bit) 6.1.1 SERIAL DATA (SDA) The Serial Data (SDA) signal is the data signal of the device. The value on this pin is latched on the rising edge of the SCL signal when the signal is an input. With the exception of the START and STOP conditions, the high or low state of the SDA pin can only change when the clock signal on the SCL pin is low. During the high period of the clock the SDA pin's value (high or low) must be stable. Changes in the SDA pin's value while the SCL pin is HIGH will be interpreted as a START or a STOP condition. 6.1.2 SERIAL CLOCK (SCL) The Serial Clock (SCL) signal is the clock signal of the device. The rising edge of the SCL signal latches the value on the SDA pin. The MCP45XX/46XX supports three I2C interface clock modes: * Standard Mode: clock rates up to 100 kHz * Fast Mode: clock rates up to 400 kHz * High-Speed Mode (HS mode): clock rates up to 3.4 MHz The MCP4XXX will not strech the clock signal (SCL) since memory read acceses occur fast enough. Depending on the clock rate mode, the interface will display different characteristics. 6.1.3 THE ADDRESS BITS (A2:A1:A0) There are up to three hardware pins used to specify the device address. The number of adress pins is determined by the part number. Address 0 is multiplexed with the High Voltage Command (HVC) function. So the state of A0 is latched on the MCP4XXX's POR/BOR event. The state of the A2 and A1 pins should be static, that is they should be tied high or tied low. 6.1.3.1 The High Voltage Command (HVC) Signal The High Voltage Command (HVC) signal is multiplexed with Address 0 (A0) and is used to indicate that the command, or sequence of commands, are in the High Voltage mode. High Voltage commands are supported for compatibility with the non-volatile devices. The HVC pin has an internal resistor connection to the MCP45XX/46XXs internal VDD signal. (c) 2008 Microchip Technology Inc. DS22096A-page 45 MCP453X/455X/463X/465X 6.2 I2C Operation 6.2.1.3 The MCP45XX/46XX's I2C module is compatible with the Philips I2C specification. The following lists some of the modules features: * 7-bit slave addressing * Supports three clock rate modes: - Standard mode, clock rates up to 100 kHz - Fast mode, clock rates up to 400 kHz - High-speed mode (HS mode), clock rates up to 3.4 MHz * Support Multi-Master Applications * General call addressing * Internal weak pull-ups on interface signals The I2C 10-bit addressing mode is not supported. The Philips I2C specification only defines the field types, field lengths, timings, etc. of a frame. The frame content defines the behavior of the device. The frame content for the MCP4XXX is defined in Section 7.0. 6.2.1 I2C BIT STATES AND SEQUENCE Figure 6-8 shows the I2C transfer sequence. The serial clock is generated by the master. The following definitions are used for the bit states: * Start bit (S) * Data bit * Acknowledge (A) bit (driven low) / No Acknowledge (A) bit (not driven low) * Repeated Start bit (Sr) * Stop bit (P) 6.2.1.1 2nd Bit SCL S FIGURE 6-2: 6.2.1.2 Start Bit. Data Bit The SDA signal may change state while the SCL signal is Low. While the SCL signal is High, the SDA signal MUST be stable (see Figure 6-5). SDA 1st Bit SDA SCL FIGURE 6-4: 2nd Bit A D0 9 8 Acknowledge Waveform. Not A (A) Response The A bit has the SDA signal high. Table 6-1 shows some of the conditions where the Slave Device will issue a Not A (A). If an error condition occurs (such as an A instead of A), then an START bit must be issued to reset the command state machine. Event The Start bit (see Figure 6-2) indicates the beginning of a data transfer sequence. The Start bit is defined as the SDA signal falling when the SCL signal is "High". 1st Bit The A bit (see Figure 6-4) is typically a response from the receiving device to the transmitting device. Depending on the context of the transfer sequence, the A bit may indicate different things. Typically the Slave device will supply an A response after the Start bit and 8 "data" bits have been received. an A bit has the SDA signal low. TABLE 6-1: Start Bit SDA Acknowledge (A) Bit MCP45XX/MCP46XX A / A RESPONSES Acknowledge Bit Response Comment General Call A Slave Address valid A Slave Address not valid A Device Memory Address and specified command (AD3:AD0 and C1:C0) are an invalid combination A After device has received address and command N.A. I2C Module Resets, or a "Don't Care" if the collision occurs on the Masters "Start bit". Bus Collision Only if GCEN bit is set SCL Data Bit FIGURE 6-3: DS22096A-page 46 Data Bit. (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 6.2.1.4 Repeated Start Bit 6.2.1.5 The Repeated Start bit (see Figure 6-5) indicates the current Master Device wishes to continue communicating with the current Slave Device without releasing the I2C bus. The Repeated Start condition is the same as the Start condition, except that the Repeated Start bit follows a Start bit (with the Data bits + A bit) and not a Stop bit. Stop Bit The Stop bit (see Figure 6-6) Indicates the end of the I2C Data Transfer Sequence. The Stop bit is defined as the SDA signal rising when the SCL signal is "High". A Stop bit resets the I2C interface of all MCP4XXX devices. SDA A / A The Start bit is the beginning of a data transfer sequence and is defined as the SDA signal falling when the SCL signal is "High". SCL P Note 1: A bus collision during the Repeated Start condition occurs if: FIGURE 6-6: Transmit Mode. * SDA is sampled low when SCL goes from low to high. 6.2.2 * SCL goes low before SDA is asserted low. This may indicate that another master is attempting to transmit a data "1". Stop Condition Receive or CLOCK STRETCHING "Clock Stretching" is something that the receiving Device can do, to allow additional time to "respond" to the "data" that has been received. The MCP4XXX will not strech the clock signal (SCL) since memory read acceses occur fast enough. 1st Bit SDA 6.2.3 SCL Sr = Repeated Start FIGURE 6-5: Waveform. ABORTING A TRANSMISSION If any part of the I2C transmission does not meet the command format, it is aborted. This can be intentionally accomplished with a START or STOP condition. This is done so that noisy transmissions (usually an extra START or STOP condition) are aborted before they corrupt the device. Repeat Start Condition SDA SCL S FIGURE 6-7: 1st Bit 2nd Bit 3rd Bit 4th Bit 5th Bit 6th Bit 7th Bit 8th Bit A/A P Typical 8-Bit I2C Waveform Format. SDA SCL START Condition FIGURE 6-8: Data allowed to change Data or A valid STOP Condition I2C Data States and Bit Sequence. (c) 2008 Microchip Technology Inc. DS22096A-page 47 MCP453X/455X/463X/465X 6.2.4 ADDRESSING The address byte is the first byte received following the START condition from the master device. The address contains four (or more) fixed bits and (up to) three user defined hardware address bits (pins A2, A1, and A0). These 7-bits address the desired I2C device. The A7:A4 address bits are fixed to "0101" and the device appends the value of following three address pins (A2, A1, A0). Address pins that are not present on the device are pulled up (a bit value of `1'). Since there are up to three adress bits controlled by hardware pins, there may be up to eight MCP4XXX devices on the same I2C bus. Figure 6-9 shows the slave address byte format, which contains the seven address bits. There is also a read/ write bit. Table 6-2 shows the fixed address for device. Hardware Address Pins The hardware address bits (A2, A1, and A0) correspond to the logic level on the associated address pins. This allows up to eight devices on the bus. These pins have a weak pull-up enabled when the VDD < VBOR. The weak pull-up utilizes the "smart" pull-up technology and exhibits the same characteristics as the High-voltage tolerant I/O structure. The state of the A0 address pin is latch on POR/BOR. This is required since High Voltage commands force this pin (HVC/A0) to the VIHH level. Slave Address S A6 A5 A4 A3 A2 A1 A0 R/W "0" "1" "0" "1" See Table 6-2 Start bit A/A R/W bit R/W = 0 = write R/W = 1 = read A bit (controlled by slave device) A = 0 = Slave Device Acknowledges byte A = 1 = Slave Device does not Acknowledge byte FIGURE 6-9: I2C Control Byte. TABLE 6-2: Slave Address Bits in the DEVICE SLAVE ADDRESSES Device Address MCP45X1 `0101 11'b + A0 Comment Supports up to devices. Note 1 MCP45X2 `0101 1'b + A1:A0 Supports up to devices. Note 1 MCP46X1 `0101'b + A2:A1:A0 Supports up to devices. Note 1 MCP46X2 `0101 1'b + A1:A0 Supports up to devices. Note 1 Note 1: A0 is used for High-Voltage commands and the value is latched at POR. 6.2.5 2 4 8 4 SLOPE CONTROL The MCP45XX/46XX implements slope control on the SDA output. As the device transitions from HS mode to FS mode, the slope control parmameter will change from the HS specification to the FS specification. For Fast (FS) and High-Speed (HS) modes, the device has a spike suppression and a Schmidt trigger at SDA and SCL inputs. DS22096A-page 48 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 6.2.6 HS MODE After switching to the High-Speed mode, the next transferred byte is the I2C control byte, which specifies the device to communicate with, and any number of data bytes plus acknowledgements. The Master Device can then either issue a Repeated Start bit to address a different device (at High-Speed) or a Stop bit to return to Fast/Standard bus speed. After the Stop bit, any other Master Device (in a Multi-Master system) can arbitrate for the I2C bus. 2 The I C specification requires that a high-speed mode device must be `activated' to operate in high-speed (3.4 Mbit/s) mode. This is done by the Master sending a special address byte following the START bit. This byte is referred to as the high-speed Master Mode Code (HSMMC). The MCP45XX/46XX device does not acknowledge this byte. However, upon receiving this command, the device switches to HS mode. The device can now communicate at up to 3.4 Mbit/s on SDA and SCL lines. The device will switch out of the HS mode on the next STOP condition. See Figure 6-10 for illustration of HS mode command sequence. For more information on the HS mode, or other I2C modes, please refer to the Phillips I2C specification. The master code is sent as follows: 1. 2. 3. 6.2.6.1 START condition (S) High-Speed Master Mode Code (0000 1XXX), The XXX bits are unique to the high-speed (HS) mode Master. No Acknowledge (A) Slope Control The slope control on the SDA output is different between the Fast/Standard Speed and the High-Speed clock modes of the interface. 6.2.6.2 Pulse Gobbler The pulse gobbler on the SCL pin is automatically adjusted to suppress spikes < 10 ns during HS mode. F/S-mode HS-mode P F/S-mode S `0 0 0 0 1 X X X'b A Sr `Slave Address' R/W A HS Select Byte Control Byte "Data" Command/Data Byte(s) S = Start bit Sr = Repeated Start bit A = Acknowledge bit A = Not Acknowledge bit R/W = Read/Write bit P = Stop bit (Stop condition terminates HS Mode) FIGURE 6-10: A/A HS-mode continues Sr `Slave Address' R/W A Control Byte HS Mode Sequence. (c) 2008 Microchip Technology Inc. DS22096A-page 49 MCP453X/455X/463X/465X 6.2.7 GENERAL CALL The General Call is a method that the "Master" device can communicate with all other "Slave" devices. In a Multi-Master application, the other Master devices are operating in Slave mode. The General Call address has two documented formats. These are shown in Figure 6-11. We have added a MCP45XX/46XX format in this figure as well. This will allow customers to have multiple I2C Digital Potentiometers on the bus and have them operate in a synchronous fashion (analogous to the DAC Sync pin functionality). If these MCP45XX/46XX 7-bit commands conflict with other I2C devices on the bus, then the customer will need two I2C busses and ensure that the devices are on the correct bus for their desired application functionality. Dual Pot devices can not update both Pot0 and Pot1 from a single command. To address this, there are General Call commands for the Wiper 0, Wiper 1, and the TCON registers. Table 6-3 shows the General Call Commands. Three commands are specified by the I2C specification and are not applicable to the MCP45XX/46XX (so command is Not Acknowledged) The MCP45XX/46XX General Call Commands are Acknowledge. Any other command is Not Acknowledged. Note: Only one General Call command per issue of the General Call control byte. Any additional General Call commands are ignored and Not Acknowledged. DS22096A-page 50 TABLE 6-3: 7-bit Command GENERAL CALL COMMANDS Comment (1, 2, 3) `1000 00d'b Write Next Byte (Third Byte) to Volatile Wiper 0 Register `1001 00d'b Write Next Byte (Third Byte) to Volatile Wiper 1 Register `1100 00d'b Write Next Byte (Third Byte) to TCON Register `1000 010'b Increment Wiper 0 Register or `1000 011'b `1001 010'b Increment Wiper 1 Register or `1001 011'b `1000 100'b Decrement Wiper 0 Register or `1000 101'b `1001 100'b Decrement Wiper 1 Register or `1001 101'b Note 1: 2: 3: Any other code is Not Acknowledged. These codes may be used by other devices on the I2C bus. The 7-bit command always appends a "0" to form 8-bits. . "d" is the D8 bit for the 9-bit write value. (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X Second Byte S 0 0 0 0 0 0 0 0 A X X X X X General Call Address X X 0 A P "7-bit Command" Reserved 7-bit Commands (By I2C Specification - Philips # 9398 393 40011, Ver. 2.1 January 2000) `0000 011'b - Reset and write programmable part of slave address by hardware. `0000 010'b - Write programmable part of slave address by hardware. `0000 000'b - NOT Allowed MCP45XX/MCP46XX 7-bit Commands `1000 01x'b - Increment Wiper 0 Register. `1001 01x'b - Increment Wiper 1 Register. `1000 10x'b - Decrement Wiper 0 Register. `1001 10x'b - Decrement Wiper 1 Register. The Following is a Microchip Extension to this General Call Format Second Byte S 0 0 0 0 0 0 0 0 General Call Address A X X X X X X d Third Byte 0 A d "7-bit Command" d d d d d d d A P "0" for General Call Command MCP45XX/MCP46XX 7-bit Commands `1000 00d'b - Write Next Byte (Third Byte) to Volatile Wiper 0 Register. `1001 00d'b - Write Next Byte (Third Byte) to Volatile Wiper 1 Register. `1100 00d'b - Write Next Byte (Third Byte) to TCON Register. The Following is a "Hardware General Call" Format Second Byte S 0 0 0 0 0 0 0 General Call Address FIGURE 6-11: 0 A X X X X X "7-bit Command" n occurrences of (Data + A) X X 1 A X X X X X X X X A P This indicates a "Hardware General Call" MCP45XX/MCP46XX will ignore this byte and all following bytes (and A), until a Stop bit (P) is encountered. General Call Formats. (c) 2008 Microchip Technology Inc. DS22096A-page 51 MCP453X/455X/463X/465X NOTES: DS22096A-page 52 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 7.0 DEVICE COMMANDS The MCP4XXX's I2C command formats are specified in this section. The I2C protocol does not specify how commands are formatted. The MCP4XXX supports four basic commands. Depending on the location accessed determines the commands that are supported. For the Volatile Wiper Registers, these commands are: * * * * Write Data Read Data Increment Data Decrement Data For the TCON Register, these commands are: * Write Data * Read Data These commands have formats for both a single command or continuous commands. These commands are shown in Table 7-1. Each command has two operational states. These operational states are referred to as: * Normal Serial Commands * High-Voltage Serial Commands Note: High Voltage commands are supported for compatibility with Non-Volatile devices in the family. TABLE 7-1: I2C COMMANDS Command Operation Mode Operates on Volatile/ # of Bit Clocks (1) Non-Volatile memory Write Data Single 29 Both Continuous 18n + 11 Volatile Only Read Data Single 29 Both Random 48 Both Continuous 18n + 11 Both Increment Single 20 Volatile Only Continuous 9n + 11 Volatile Only Decrement Single 20 Volatile Only Continuous 9n + 11 Volatile Only Note 1: "n" indicates the number of times the command operation is to be repeated. 7.1 Command Byte The MCP4XXX's Command Byte has three fields: the Address, the Command Operation, and 2 Data bits, see Figure 7-1. Currently only one of the data bits is defined (D8). The device memory is accessed when the Master sends a proper Command Byte to select the desired operation. The memory location getting accessed is contained in the Command Byte's AD3:AD0 bits. The action desired is contained in the Command Byte's C1:C0 bits, see Table 7-1. C1:C0 determines if the desired memory location will be read, written, Incremented (wiper setting +1) or Decremented (wiper setting -1). The Increment and Decrement commands are only valid on the volatile wiper registers. If the Address bits and Command bits are not a valid combination, then the MCP4XXX will generate a Not Acknowledge pulse to indicate the invalid combination. The I2C Master device must then force a Start Condition to reset the MCP4XXX's 2C module. D9 and D8 are the most significant bits for the digital potentiometer's wiper setting. The 8-bit devices utilize D8 as their MSb while the 7-bit devices utilize D7 (from the data byte) as it's MSb. COMMAND BYTE A A A A A C C D D A D D D D 1 0 9 8 3 2 1 0 MSbits (Data) MCP4XXX Memory Address Command Operation bits 00 = Write Data 01 = Increment 10 = Decrement 11 = Read Data FIGURE 7-1: Command Byte Format. Normal serial commands are those where the HVC pin is driven to VIH or VIL. With High-Voltage Serial Commands, the HVC pin is driven to VIHH. In each mode, there are four possible commands. Table 7-2 shows the supported commands for each memory location. Table 7-3 shows an overview of all the device commands and their interaction with other device features. (c) 2008 Microchip Technology Inc. DS22096A-page 53 MCP453X/455X/463X/465X TABLE 7-2: MEMORY MAP AND THE SUPPORTED COMMANDS Address Command Operation Value 00h 01h Function Volatile Wiper 0 Volatile Wiper 1 Data (10-bits) (1) Write Data nn nnnn nnnn Read Data (3) nn nnnn nnnn Increment Wiper -- Decrement Wiper -- Write Data nn nnnn nnnn Read Data (3) nn nnnn nnnn Increment Wiper -- Decrement Wiper -- 02h Reserved -- -- 03h Reserved -- -- 04h (2) 05h (2) Volatile TCON Register Write Data Reserved 06h - 0Fh (2) Reserved Note 1: 2: 3: nn nnnn nnnn Read Data (3) nn nnnn nnnn Read Data (3) nn nnnn nnnn -- Comment Maps to Non-Volitile MCP45XX/46XX device's STATUS Register -- The Data Memory is only 9-bits wide, so the MSb is ignored by the device. Increment or Decrement commands are invalid for these addresses. I2C read operation will read 2 bytes, of which the 10-bits of data are contained within. DS22096A-page 54 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 7.2 Data Byte 7.3 Only the Read Command and the Write Command have Data Byte(s). The Write command concatenates the 8-bits of the Data Byte with the one data bit (D8) contained in the Command Byte to form 9-bits of data (D8:D0). The Command Byte format supports up to 9-bits of data so that the 8-bit resistor network can be set to Full-Scale (100h or greater). This allows wiper connections to Terminal A and to Terminal B. The D9 bit is currently unused. Error Condition If the four address bits received (AD3:AD0) and the two command bits received (C1:C0) are a valid combination, the MCP4XXX will Acknowledge the I2C bus. If the address bits and command bits are an invalid combination, then the MCP4XXX will Not Acknowledge the I2C bus. Once an error condition has occurred, any following commands are ignored until the I2C bus is reset with a Start Condition. 7.3.1 ABORTING A TRANSMISSION A Restart or Stop condition in the expected data bit position will abort the current command sequence and TABLE 7-3: COMMANDS # of Bits High Voltage (VIHH) on HVC pin? Write Data 29 -- Read Data 29 -- Increment Wiper 20 -- Command Name Decrement Wiper 20 -- High Voltage Write Data 29 Yes High Voltage Read Data 29 Yes High Voltage Increment Wiper 20 Yes High Voltage Decrement Wiper 20 Yes (c) 2008 Microchip Technology Inc. DS22096A-page 55 MCP453X/455X/463X/465X 7.4 Write Data Normal and High Voltage The Write Command can be issued to both the Volatile and Non-Volatile memory locations. The format of the command, see Figure 7-2, includes the I2C Control Byte, an A bit, the MCP4XXX Command Byte, an A bit, the MCP4XXX Data Byte, an A bit, and a Stop (or Restart) condition. The MCP4XXX generates the A / A bits. A Write command to a Volatile memory location changes that location after a properly formatted Write Command and the A / A clock have been received. 7.4.1 SINGLE WRITE TO VOLATILE MEMORY For volatile memory locations, data is written to the MCP4XXX after every byte transfer (during the Acknowledge). If a Stop or Restart condition is generated during a data transfer (before the A), the data will not be written to the MCP4XXX. After the A bit, the master can initiate the next sequence with a Stop or Restart condition. 7.4.2 CONTINUOUS WRITES TO VOLATILE MEMORY A continuous write mode of operation is possible when writing to the volatile memory registers (address 00h, 01h, and 04h). This continuous write mode allows writes without a Stop or Restart condition or repeated transmissions of the I2C Control Byte. Figure 7-3 shows the sequence for three continuous writes. The writes do not need to be to the same volatile memory address. The sequence ends with the master sending a STOP or RESTART condition. 7.4.3 THE HIGH VOLTAGE COMMAND (HVC) SIGNAL The High Voltage Command (HVC) signal is multiplexed with Address 0 (A0) and is used to indicate that the command, or sequence of commands, are in the High Voltage operational state. High Voltage commands allow the device's WiperLock Technology and write protect features to be enabled and disabled. The HVC pin has an internal resistor connection to the MCP45XX/46XXs internal VDD signal. Refer to Figure 7-2 for the byte write sequence. DS22096A-page 56 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X Write bit S 0 1 0 Device Memory Address Variable Address Fixed Address 1 A2 A1 A0 0 A AD AD AD AD 3 2 1 0 0 0 x D8 A D7 D6 D5 D4 D3 D2 D1 D0 A P WRITE Command Control Byte Write bit Fixed Address S 0 1 Variable Address 0 1 A2 A1 A0 0 A Device Memory Address Write "Data" bits Command AD AD AD AD 3 2 1 0 0 0 x D8 A D7 D6 D5 D4 D3 D2 D1 D0 A WRITE Command Control Byte AD AD AD AD 3 2 1 0 0 Write Data bits 0 x D8 A D7 D6 D5 D4 D3 D2 D1 D0 A WRITE Command AD AD AD AD 3 2 1 0 0 Write Data bits STOP bit 0 x D8 A D7 D6 D5 D4 D3 D2 D1 D0 A P WRITE Command FIGURE 7-3: Write Data bits I2C Write Sequence. FIGURE 7-2: Note: Write "Data" bits Command Write Data bits Only functions when writing the volatile wiper registers (AD3:AD0 = 00h, 01h, and 04h) or the TCON register I2C Continuous Volatile Wiper Write. (c) 2008 Microchip Technology Inc. DS22096A-page 57 MCP453X/455X/463X/465X 7.5 Read Data Normal and High Voltage 7.5.1 SINGLE READ Figure 7-4 show the waveforms for a single read. The Read Command can be issued to both the Volatile and Non-Volatile memory locations. The format of the command, see Figure 7-4, includes the Start condition, I2C Control Byte (with R/W bit set to "0"), A bit, MCP4XXX Command Byte, A bit, followed by a Repeated Start bit, I2C Control Byte (with R/W bit set to "1"), and the MCP4XXX transmitting the requested Data High Byte, and A bit, the Data Low Byte, the Master generating the A, and Stop condition. For single reads the master sends a STOP or RESTART condition after the data byte is sent from the slave. The I2C Control Byte requires the R/W bit equal to a logic one (R/W = 1) to generate a read sequence. The memory location read will be the last address contained in a valid write MCP4XXX Command Byte or address 00h if no write operations have occurred since the device was reset (Power-on Reset or Brown-out Reset). 7.5.2 Read operations initially include the same address byte sequence as the write sequence (shown in Figure 6-9). This sequence is followed by another control byte (including the Start condition and Ackowledge) with the R/W bit equal to a logic one (R/W = 1) to indicate a read. The MCP4XXX will then transmit the data contained in the addressed register. This is followed by the master generating an A bit in preparation for more data, or an A bit followed by a Stop. The sequence is ended with the master generating a Stop or Restart condition. The internal address pointer is maintained. 7.5.1.1 Random Read Figure 7-5 shows the sequence for a Random Reads. Refer to Figure 7-5 for the random byte read sequence. CONTINUOUS READS Continuous reads allows the devices memory to be read quickly. Continuous reads are possible to all memory locations. If a non-volatile memory write cycle is occurring, then Read commands may only access the volatile memory locations. Figure 7-6 shows the sequence for three continuous reads. For continuous reads, instead of transmitting a Stop or Restart condition after the data transfer, the master reads the next data byte. The sequence ends with the master Not Acknowledging and then sending a Stop or Restart. 7.5.3 THE HIGH VOLTAGE COMMAND (HVC) SIGNAL The High Voltage Command (HVC) signal is multiplexed with Address 0 (A0) and is used to indicate that the command, or sequence of commands, are in the High Voltage mode. High Voltage commands allow the device's WiperLock Technology and write protect features to be enabled and disabled. The HVC pin has an internal resistor connection to the MCP4XXXs internal VDD signal. 7.5.4 IGNORING AN I2C TRANSMISSION AND "FALLING OFF" THE BUS The MCP4XXX expects to receive entire, valid I2C commands and will assume any command not defined as a valid command is due to a bus corruption and will enter a passive high condition on the SDA signal. All signals will be ignored until the next valid Start condition and Control Byte are received. DS22096A-page 58 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X Read bit Fixed Address S 0 1 0 STOP bit Variable Address Read Data bits 1 A2 A1 A0 1 A 0 0 0 0 D8 A1 D7 D6 D5 D4 D3 D2 D1 D0 A2 0 0 0 P Read bits Control Byte Note 1: Master Device is responsible for A / A signal. If a A signal occurs, the MCP45XX/46XX will abort this transfer and release the bus. 2: The Master Device will Not Acknowledge, and the MCP45XX/46XX will release the bus so the Master Device can generate a Stop or Repeated Start condition. 3: The MCP45xx/46xx retains the last "Device Memory Address" that it has received. This is the MCP45XX/46XX does not "corrupt" the "Device Memory Address" after Repeated Start or Stop conditions. 4: The Device Memory Address pointer defaults to 00h on POR and BOR conditions. I2C Read (Last Memory Address Accessed). FIGURE 7-4: Write bit Fixed Address S 0 Repeated Start bit Device Memory Address Variable Address 1 0 1 A2 A1 A0 0 A Command AD AD AD AD 3 2 1 0 1 1 x X A Sr READ Command Control Byte STOP bit Read bit 0 1 0 1 A2 A1 A0 1 A 0 Control Byte Read Data bits 0 0 0 0 0 0 D8 A1 D7 D6 D5 D4 D3 D2 D1 D0 A2 P Read bits Note 1: Master Device is responsible for A / A signal. If a A signal occurs, the MCP45XX/46XX will abort this transfer and release the bus. 2: The Master Device will Not Acknowledge, and the MCP45XX/46XX will release the bus so the Master Device can generate a Stop or Repeated Start condition. 3: The MCP45XX/46XX retains the last "Device Memory Address" that it has received. This is the MCP45XX/46XX does not "corrupt" the "Device Memory Address" after Repeated Start or Stop conditions. FIGURE 7-5: I2C Random Read. (c) 2008 Microchip Technology Inc. DS22096A-page 59 MCP453X/455X/463X/465X Read bit Fixed Address S 0 1 0 Variable Address Read Data bits 1 A2 A1 A0 1 0 A 0 0 0 0 0 0 D8 A1 D7 D6 D5 D4 D3 D2 D1 D0 A1 Read bits Control Byte Read Data bits 0 0 0 0 0 0 0 D8 A1 D7 D6 D5 D4 D3 D2 D1 D0 A1 STOP bit Read Data bits 0 0 0 0 0 0 0 D8 A1 D7 D6 D5 D4 D3 D2 D1 D0 A2 P Note 1: Master Device is responsible for A / A signal. If a A signal occurs, the MCP45XX/46XX will abort this transfer and release the bus. 2: The Master Device will Not Acknowledge, and the MCP45XX/46XX will release the bus so the Master Device can generate a Stop or Repeated Start condition. FIGURE 7-6: DS22096A-page 60 I2C Continuos Reads. (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 7.6 Increment Wiper Normal and High Voltage TABLE 7-4: Current Wiper Setting The Increment Command provide a quick and easy method to modify the potentiometer's wiper by +1 with minimal overhead. The Increment Command will only function on the volatile wiper setting memory locations 00h and 01h. Note: Table 7-2 shows the valid addresses for the Increment Wiper command. Other addresses are invalid. When executing an Increment Command, the volatile wiper setting will be altered from n to n+1 for each Increment Command received. The value will increment up to 100h max on 8-bit devices and 80h on 7-bit devices. If multiple Increment Commands are received after the value has reached 100h (or 80h), the value will not be incremented further. Table 7-4 shows the Increment Command versus the current volatile wiper value. Write bit S 0 1 0 1 A2 A1 A0 0 Control Byte A Device Memory Address 3FFh 081h 3FFh 101h Reserved No (Full-Scale (W = A)) 080h 100h Full-Scale (W = A) 07Fh 041h 0FFh 081 W=N 040h 080h W = N (Mid-Scale) 03Fh 001h 07Fh 001 W=N 000h 000h Zero Scale (W = B) Yes Note: The advantage of using an Increment Command instead of a read-modify-write series of commands is speed and simplicity. The wiper will transition after each Command Acknowledge when accessing the volatile wiper registers. Variable Address 8-bit Pot No Yes THE HIGH VOLTAGE COMMAND (HVC) SIGNAL The High Voltage Command (HVC) signal is multiplexed with Address 0 (A0) and is used to indicate that the command, or sequence of commands, are in the High Voltage mode. Signals > VIHH (~8.5V) on the HVC/A0 pin puts MCP45XX/46XX devices into High Voltage mode. The command sequence can go from an increment to any other valid command for the specified address. Fixed Address Increment Command Operates? Wiper (W) Properties 7-bit Pot 7.6.1 Refer to Figure 7-7 for the Increment Command sequence. The sequence is terminated by the Stop condition. So when executing a continuous command string, The Increment command can be followed by any other valid command. this means that writes do not need to be to the same volatile memory address. Note: INCREMENT OPERATION VS. VOLATILE WIPER VALUE There is a required delay after the HVC pin is driven to the VIHH level to the 1st edge of the SCL pin. The HVC pin has an internal resistor connection to the MCP45XX/46XXs internal VDD signal. Command AD AD AD AD 3 2 1 0 0 1 x AD AD AD AD X A 4 3 2 1 0 INCR Command (n+1) 1 x X A P (2) INCR Command (n+2) Note 1: Increment Command (INCR) only functions when accessing the volatile wiper reg- isters (AD3:AD0 = 0h and 1h). 2: This command sequence does not need to terminate (using the Stop bit) and can change to any other desired command sequence (Increment, Read, or Write). FIGURE 7-7: I2C Increment Command Sequence. (c) 2008 Microchip Technology Inc. DS22096A-page 61 MCP453X/455X/463X/465X 7.7 Decrement Wiper Normal and High Voltage TABLE 7-5: Current Wiper Setting The Decrement Command provide a quick and easy method to modify the potentiometer's wiper by -1 with minimal overhead. The Decrement Command will only function on the volatile wiper setting memory locations 00h and 01h. Note: Table 7-2 shows the valid addresses for the Decrement Wiper command. Other addresses are invalid. When executing a Decrement Command, the volatile wiper setting will be altered from n to n-1 for each Decrement Command received. The value will decrement down to 000h min. If multiple Decrement Commands are received after the value has reached 000h, the value will not be decremented further. Table 7-5 shows the Increment Command versus the current volatile wiper value. Refer to Figure 7-8 for the Decrement Command sequence. The sequence is terminated by the Stop condition. So when executing a continuous command string, The Increment command can be followed by any other valid command. this means that writes do not need to be to the same volatile memory address. Note: The command sequence can go from an increment to any other valid command for the specified address. The advantage of using an Decrement Command instead of a read-modify-write series of commands is speed and simplicity. The wiper will transition after each Command Acknowledge when accessing the volatile wiper registers. Write bit Fixed Address S 0 Variable Address 1 0 1 A2 A1 A0 0 A Control Byte DECREMENT OPERATION VS. VOLATILE WIPER VALUE Wiper (W) Properties Decrement Command Operates? 7-bit Pot 8-bit Pot 3FFh 081h 3FFh 101h Reserved No (Full-Scale (W = A)) 080h 100h Full-Scale (W = A) 07Fh 041h 0FFh 081 W=N 040h 080h W = N (Mid-Scale) 03Fh 001h 07Fh 001 W=N 000h 000h Zero Scale (W = B) No 7.7.1 Yes Yes THE HIGH VOLTAGE COMMAND (HVC) SIGNAL The High Voltage Command (HVC) signal is multiplexed with Address 0 (A0) and is used to indicate that the command, or sequence of commands, are in the High Voltage mode. Signals > VIHH (~8.5V) on the HVC/A0 pin puts MCP45XX/46XX devices into High Voltage mode. Note: There is a required delay after the HVC pin is driven to the VIHH level to the 1st edge of the SCL pin. The HVC pin has an internal resistor connection to the MCP45XX/46XXs internal VDD signal. Device Memory Address Command AD AD AD AD 3 2 1 0 1 AD AD AD AD 0 X X A 4 3 2 1 1 DECR Command (n-1) 0 X X A P (2) DECR Command (n-2) Note 1: Decrement Command (DECR) only functions when accessing the volatile wiper registers (AD3:AD0 = 0h and 1h). 2: This command sequence does not need to terminate (using the Stop bit) and can change to any other desired command sequence (INCR, Read, or Write). FIGURE 7-8: DS22096A-page 62 I2C Decrement Command Sequence. (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 8.0 APPLICATIONS EXAMPLES Non-volatile digital potentiometers have a multitude of practical uses in modern electronic circuits. The most popular uses include precision calibration of set point thresholds, sensor trimming, LCD bias trimming, audio attenuation, adjustable power supplies, motor control overcurrent trip setting, adjustable gain amplifiers and offset trimming. The MCP453X/455X/463X/465X devices can be used to replace the common mechanical trim pot in applications where the operating and terminal voltages are within CMOS process limitations (VDD = 2.7V to 5.5V). 8.1 Techniques to force the HVC pin to VIHH The circuit in Figure 8-1 shows a method using the TC1240A doubling charge pump. When the SHDN pin is high, the TC1240A is off, and the level on the HVC pin is controlled by the PIC(R) microcontrollers (MCUs) IO2 pin. When the SHDN pin is low, the TC1240A is on and the VOUT voltage is 2 * VDD. The resistor R1 allows the HVC pin to go higher than the voltage such that the PIC MCU's IO2 pin "clamps" at approximately VDD. The circuit in Figure 8-2 shows the method used on the MCP402X Non-volatile Digital Potentiometer Evaluation Board (Part Number: MCP402XEV). This method requires that the system voltage be approximately 5V. This ensures that when the PIC10F206 enters a brown-out condition, there is an insufficient voltage level on the HVC pin to change the stored value of the wiper. The MCP402X Non-volatile Digital Potentiometer Evaluation Board User's Guide (DS51546) contains a complete schematic. GP0 is a general purpose I/O pin, while GP2 can either be a general purpose I/O pin or it can output the internal clock. For the serial commands, configure the GP2 pin as an input (high impedance). The output state of the GP0 pin will determine the voltage on the HVC pin (VIL or VIH). For high-voltage serial commands, force the GP0 output pin to output a high level (VOH) and configure the GP2 pin to output the internal clock. This will form a charge pump and increase the voltage on the HVC pin (when the system voltage is approximately 5V). PIC10F206 R1 GP0 MCP4XXX PIC MCU TC1240A C+ VIN CSHDN C1 VOUT IO1 R1 IO2 MCP45XX HVC MCP46XX C2 GP2 HVC C1 C2 FIGURE 8-2: MCP4XXX Non-Volatile Digital Potentiometer Evaluation Board (MCP402XEV) implementation to generate the VIHH voltage. FIGURE 8-1: Using the TC1240A to generate the VIHH voltage. (c) 2008 Microchip Technology Inc. DS22096A-page 63 MCP453X/455X/463X/465X 8.2 Using Shutdown Figure 8-3 shows a possible application circuit where the independent terminals could be used. Disconnecting the wiper allows the transistor input to be taken to the Bias voltage level (disconnecting A and or B may be desired to reduce system current). Disconnecting Terminal A modifies the transistor input by the RBW rheostat value to the Common B. Disconnecting Terminal B modifies the transistor input by the RAW rheostat value to the Common A. The Common A and Common B connections could be connected to VDD and VSS. Common A Input A To base of Transistor (or Amplifier) W B Common B Note: `1' `1' `1' S P Nine bits of `1' Start bit Start bit Stop bit FIGURE 8-4: Format. Software Reset Sequence The 1st Start bit will cause the device to reset from a state in which it is expecting to receive data from the Master Device. In this mode, the device is monitoring the data bus in Receive mode and can detect the Start bit forces an internal Reset. The nine bits of `1' are used to force a Reset of those devices that could not be reset by the previous Start bit. This occurs only if the MCP45XX/46XX is driving an A bit on the I2C bus, or is in output mode (from a Read command) and is driving a data bit of `0' onto the I2C bus. In both of these cases, the previous Start bit could not be generated due to the MCP45XX/46XX holding the bus low. By sending out nine `1' bits, it is ensured that the device will see a A bit (the Master Device does not drive the I2C bus low to acknowledge the data sent by the MCP45XX/46XX), which also forces the MCP45XX/46XX to reset. Bias FIGURE 8-3: Example Application Circuit using Terminal Disconnects. 8.3 `1' `1' `1' `1' `1' The 2nd Start bit is sent to address the rare possibility of an erroneous write. This could occur if the Master Device was reset while sending a Write command to the MCP45XX/46XX, AND then as the Master Device returns to normal operation and issues a Start condition while the MCP45XX/46XX is issuing an Acknowledge. In this case, if the 2nd Start bit is not sent (and the Stop bit was sent) the MCP45XX/46XX could initiate a write cycle. Input Balance S Software Reset Sequence This technique is documented in AN1028. At times it may become necessary to perform a Software Reset Sequence to ensure the MCP45XX/46XX device is in a correct and known I2C Interface state. This technique only resets the I2C state machine. Note: The potential for this erroneous write ONLY occurs if the Master Device is reset while sending a Write command to the MCP45XX/46XX. The Stop bit terminates the current I2C bus activity. The MCP45XX/46XX wait to detect the next Start condition. This sequence does not effect any other I2C devices which may be on the bus, as they should disregard this as an invalid command. This is useful if the MCP45XX/46XX device powers up in an incorrect state (due to excessive bus noise, ...), or if the Master Device is reset during communication. Figure 8-4 shows the communication sequence to software reset the device. DS22096A-page 64 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 8.4 Figure 8-5 shows two I2C bus configurations. In many cases, the single I2C bus configuration will be adequate. For applications that do not want all the MCP45XX/46XX devices to do General Call support or have a conflict with General Call commands, the multiple I2C bus configuration would be used. Using the General Call Command The use of the General Call Address Increment, Decrement, or Write commands is analogous to the "Load" feature (LDAC pin) on some DACs (such as the MCP4921). This allows all the devices to "Update" the output level "at the same time". For some applications, the ability to update the wiper values "at the same time may be a requirement, since they delay from writing to one wiper value and then the next may cause application issues. A possible example would be a "tuned" circuit that uses several MCP45XX/ 46XX in rheostat configuration. As the system condition changes (temperature, load, ...) these devices need to be changed (incremented/decremented) to adjust for the system change. These changes will either be in the same direction or in opposite directions. With the Potentiometer device the customer can either select the PxB terminals (same direction) or the PxA terminal(s) (opposite direction). Single I2C Bus Configuration Device 1 Device n Host Controller Device 4 Device 2 Multiple I2C Bus Configuration Device 1a Device 3a Device na Host Bus a Controller Figure 8-6 shows that the update of six devices takes 6*TI2CDLY time in "normal" operation, but only 1*TI2CDLY time in "General Call" operation. Note: Device 3 Device 4a Device 2a The application system may need to partition the I2C bus into multiple busses to ensure that the MCP45XX/46XX General Call commands do not conflict with the General Call commands that the other I2C devices may have defined. Also if only a portion of the MCP45XX/46XX devices are to require this synchronous operation, then the devices that should not receive these commands should be on the second I2C bus. Device 1b Device 3b Device nb Bus b Device 4b Device 2b Device 1n Device 3n Device nn Bus n Device 2n FIGURE 8-5: Configurations. Device 4n Typical Application I2C Bus Normal Operation INC POT01 TI2CDLY INC POT02 TI2CDLY INC POT03 TI2CDLY INC POT04 TI2CDLY INC POT05 TI2CDLY INC POT06 TI2CDLY General Call Operation INC POTs 01-06 TI2CDLY INC POTs 01-06 TI2CDLY INC POTs 01-06 TI2CDLY INC POTs 01-06 TI2CDLY INC POTs 01-06 TI2CDLY INC POTs 01-06 TI2CDLY TI2CDLY = Time from one I2C command completed to completing the next I2C command. FIGURE 8-6: Updates. Example Comparison of "Normal Operation" vs. "General Call Operation" wiper (c) 2008 Microchip Technology Inc. DS22096A-page 65 MCP453X/455X/463X/465X 8.5 Design Considerations 8.5.2 In the design of a system with the MCP4XXX devices, the following considerations should be taken into account: * Power Supply Considerations * Layout Considerations 8.5.1 POWER SUPPLY CONSIDERATIONS The typical application will require a bypass capacitor in order to filter high-frequency noise, which can be induced onto the power supply's traces. The bypass capacitor helps to minimize the effect of these noise sources on signal integrity. Figure 8-7 illustrates an appropriate bypass strategy. In this example, the recommended bypass capacitor value is 0.1 F. This capacitor should be placed as close (within 4 mm) to the device power pin (VDD) as possible. The power source supplying these devices should be as clean as possible. If the application circuit has separate digital and analog power supplies, VDD and VSS should reside on the analog plane. VDD LAYOUT CONSIDERATIONS Inductively-coupled AC transients and digital switching noise can degrade the input and output signal integrity, potentially masking the MCP4XXX's performance. Careful board layout minimizes these effects and increases the Signal-to-Noise Ratio (SNR). Multi-layer boards utilizing a low-inductance ground plane, isolated inputs, isolated outputs and proper decoupling are critical to achieving the performance that the silicon is capable of providing. Particularly harsh environments may require shielding of critical signals. If low noise is desired, breadboards and wire-wrapped boards are not recommended. 8.5.3 RESISTOR TEMPCO Characterization curves of the resistor temperature coefficient (Tempco) are shown in Figure 2-12, Figure 2-25, Figure 2-38, and Figure 2-51. These curves show that the resistor network is designed to correct for the change in resistance as temperature increases. This technique reduces the end to end change is RAB resistance. 8.5.4 HIGH VOLTAGE TOLERANT PINS High Voltage support (VIHH) on the Serial Interface pins is for compatibility with the non-volatile devices.. 0.1 F VDD W B VSS FIGURE 8-7: Connections. DS22096A-page 66 SCL PIC(R) Microcontroller A MCP453X/455X/ 463X/465X 0.1 F SDA VSS Typical Microcontroller (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 9.0 DEVICE OPTIONS Additional, custom devices are available. These devices have weak pull-up resistors on the SDA and SCL pins. This is useful for applications where the wiper value is programmed durning manufacture and not modified by the system during normal operation. Please contact your local sales office for current information and minimum volumn requirements. 9.1 Custom Options The custom device will have a "P" (for Pull-up) after the resistance version in the Product Identification System. These device will not be available through Microchip's online Microchip Direct nor Microchip's Sample systems. Example part number: MCP4631-103PE/ST (c) 2008 Microchip Technology Inc. DS22096A-page 67 MCP453X/455X/463X/465X NOTES: DS22096A-page 68 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 10.0 DEVELOPMENT SUPPORT 10.1 Development Tools 10.2 Technical Documentation Several additional technical documents are available to assist you in your design and development. These technical documents include Application Notes, Technical Briefs, and Design Guides. Table 10-2 shows some of these documents. Several development tools are available to assist in your design and evaluation of the MCP45XX/46XX devices. The currently available tools are shown in Table 10-1. These boards may be purchased directly from the Microchip web site at www.microchip.com. TABLE 10-1: DEVELOPMENT TOOLS Board Name Part # Supported Devices MCP42XX PICTail Plus Daughter Board (2) MCP42XXDM-PTPLS MCP42XX MCP4XXX Digital Potentiometer Daughter Board (1) MCP4XXXDM-DB MCP42XXX, MCP42XX, MCP46XX, MCP4021, and MCP4011 8-pin SOIC/MSOP/TSSOP/DIP Evaluation Board SOIC8EV Any 8-pin device in DIP, SOIC, MSOP, or TSSOP package 14-pin SOIC/MSOP/DIP Evaluation Board SOIC14EV Any 14-pin device in DIP, SOIC, or MSOP package Note 1: Requires the use of a PICDEM Demo Board (see User's Guide for details) 2: Requires the use of the PIC24 Explorer 16 Demo Board (see User's Guide for details) 3: The desired MCP46XX device (in MSOP package) must be soldered onto the extra board. TABLE 10-2: TECHNICAL DOCUMENTATION Application Note Number Title Literature # AN1080 Understanding Digital Potentiometers Resistor Variations DS01080 AN737 Using Digital Potentiometers to Design Low Pass Adjustable Filters DS00737 AN692 Using a Digital Potentiometer to Optimize a Precision Single Supply Photo Detect DS00692 AN691 Optimizing the Digital Potentiometer in Precision Circuits DS00691 AN219 Comparing Digital Potentiometers to Mechanical Potentiometers DS00219 -- Digital Potentiometer Design Guide DS22017 -- Signal Chain Design Guide DS21825 (c) 2008 Microchip Technology Inc. DS22096A-page 69 MCP453X/455X/463X/465X NOTES: DS22096A-page 70 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 11.0 PACKAGING INFORMATION 11.1 Package Marking Information 8-Lead DFN (3x3) XXXX XYWW NNN Example: Part Number Code Part Number Code MCP4531-502E/MF DACA MCP4532-502E/MF DACE MCP4531-103E/MF DACB MCP4532-103E/MF DACF MCP4531-104E/MF DACD MCP4532-104E/MF DACH MCP4531-503E/MF DACC MCP4532-503E/MF DACG MCP4551-502E/MF DACT MCP4552-502E/MF DACX MCP4551-103E/MF DACU MCP4552-103E/MF DACY MCP4551-104E/MF DACW MCP4552-104E/MF DADA MCP4551-503E/MF DACV MCP4552-503E/MF DACZ Part Number Code Part Number Code MCP4531-103E/MS 453113 MCP4532-103E/MS 453213 MCP4531-104E/MS 453114 MCP4532-104E/MS 453214 MCP4531-502E/MS 453152 MCP4532-502E/MS 453252 MCP4531-503E/MS 453153 MCP4532-503E/MS 453253 MCP4551-103E/MS 455113 MCP4552-103E/MS 455213 MCP4551-104E/MS 455114 MCP4552-104E/MS 455214 MCP4551-502E/MS 455152 MCP4552-502E/MS 455252 MCP4551-503E/MS 455153 MCP4552-503E/MS 455253 8-Lead MSOP XXXXXX YWWNNN Legend: XX...X Y YY WW NNN e3 * Note: DACA E828 256 Example 453113 828256 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2008 Microchip Technology Inc. DS22096A-page 71 MCP453X/455X/463X/465X Package Marking Information (Continued) 10-Lead DFN (3x3) XXXX YYWW NNN Example: Part Number Code Part Number Code MCP4632-502E/MF AABA MCP4652-502E/MF AAKA MCP4632-103E/MF AACA MCP4652-103E/MF AALA MCP4632-104E/MF AAEA MCP4652-104E/MF AAPA MCP4632-503E/MF AADA MCP4652-503E/MF AAMA AAFA 0828 256 Example 10-Lead MSOP XXXXXX YWWNNN Part Number Code Part Number Code MCP4632-502E/UN 463252 MCP4652-502E/UN 465252 MCP4632-103E/UN 463213 MCP4652-103E/UN 465213 MCP4632-104E/UN 463214 MCP4652-104E/UN 465214 MCP4632-503E/UN 463253 MCP4652-503E/UN 465253 14-Lead TSSOP (MCP4631, MCP4651) 828256 Example XXXXXXXX 4631502E YYWW 0828 NNN 256 16-Lead QFN (MCP4631, MCP4651) XXXXX XXXXXX XXXXXX YYWWNNN DS22096A-page 72 463252 Example 4631 502 e3 E/ML^^ 828256 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X /HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH 0) [[PP%RG\>')1@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D e b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c) 2008 Microchip Technology Inc. DS22096A-page 73 MCP453X/455X/463X/465X /HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH 0) [[PP%RG\>')1@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ DS22096A-page 74 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X /HDG3ODVWLF0LFUR6PDOO2XWOLQH3DFNDJH 06 >0623@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D N E E1 NOTE 1 1 2 e b A2 A c L L1 A1 8QLWV 'LPHQVLRQ/LPLWV 1XPEHURI3LQV 0,//,0(7(56 0,1 1 120 0$; 3LWFK H 2YHUDOO+HLJKW $ %6& 0ROGHG3DFNDJH7KLFNQHVV $ 6WDQGRII $ 2YHUDOO:LGWK ( 0ROGHG3DFNDJH:LGWK ( %6& 2YHUDOO/HQJWK ' %6& )RRW/HQJWK / )RRWSULQW / %6& 5() )RRW$QJOH /HDG7KLFNQHVV F /HDG:LGWK E 1RWHV 3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD 'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH 'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0 %6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV 5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\ 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &% (c) 2008 Microchip Technology Inc. DS22096A-page 75 MCP453X/455X/463X/465X /HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH 0) [[PP%RG\>')1@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D e b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page 76 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X /HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH 0) [[PP%RG\>')1@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ (c) 2008 Microchip Technology Inc. DS22096A-page 77 MCP453X/455X/463X/465X /HDG3ODVWLF0LFUR6PDOO2XWOLQH3DFNDJH 81 >0623@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D N E E1 NOTE 1 1 2 b e A A2 c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page 78 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X /HDG3ODVWLF7KLQ6KULQN6PDOO2XWOLQH 67 PP%RG\>76623@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D N E E1 NOTE 1 1 2 e b A2 A c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c) 2008 Microchip Technology Inc. DS22096A-page 79 MCP453X/455X/463X/465X /HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 0/ [[PP%RG\>4)1@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D2 D EXPOSED PAD e E E2 2 2 1 b 1 TOP VIEW K N N NOTE 1 L BOTTOM VIEW A3 A A1 8QLWV 'LPHQVLRQ/LPLWV 1XPEHURI3LQV 0,//,0(7(56 0,1 1 120 0$; 3LWFK H 2YHUDOO+HLJKW $ 6WDQGRII $ &RQWDFW7KLFNQHVV $ 2YHUDOO:LGWK ( ([SRVHG3DG:LGWK ( 2YHUDOO/HQJWK ' ([SRVHG3DG/HQJWK %6& 5() %6& %6& ' &RQWDFW:LGWK E &RQWDFW/HQJWK / &RQWDFWWR([SRVHG3DG . 1RWHV 3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD 3DFNDJHLVVDZVLQJXODWHG 'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0 %6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV 5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\ 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &% DS22096A-page 80 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ (c) 2008 Microchip Technology Inc. DS22096A-page 81 MCP453X/455X/463X/465X NOTES: DS22096A-page 82 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X APPENDIX A: REVISION HISTORY Revision A (November 2008) * Original Release of this Document. (c) 2008 Microchip Technology Inc. DS22096A-page 83 MCP453X/455X/463X/465X NOTES: DS22096A-page 84 (c) 2008 Microchip Technology Inc. MCP453X/455X/463X/465X PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device XXX X /XX Resistance Temperature Package Version Range Device: MCP4531: MCP4531T: MCP4532: MCP4532T: MCP4551: MCP4551T: MCP4552: MCP4552T: MCP4631: MCP4631T: MCP4632: MCP4632T: MCP4651: MCP4651T: MCP4652: MCP4652T: Resistance Version: Single Non-Volatile 7-bit Potentiometer Single Non-Volatile 7-bit Potentiometer (Tape and Reel) Single Non-Volatile 7-bit Rheostat Single Non-Volatile 7-bit Rheostat (Tape and Reel) Single Non-Volatile 8-bit Potentiometer Single Non-Volatile 8-bit Potentiometer (Tape and Reel) Single Non-Volatile8-bit Rheostat Single Non-Volatile 8-bit Rheostat (Tape and Reel) Dual Non-Volatile 7-bit Potentiometer Dual Non-Volatile 7-bit Potentiometer (Tape and Reel) Dual Non-Volatile 7-bit Rheostat Dual Non-Volatile 7-bit Rheostat (Tape and Reel) Dual Non-Volatile 8-bit Potentiometer Dual Non-Volatile 8-bit Potentiometer (Tape and Reel) Dual Non-Volatile8-bit Rheostat Dual Non-Volatile 8-bit Rheostat (Tape and Reel) 502 = 5 k 103 = 10 k 503 = 50 k 104 = 100 k Temperature Range: E = -40C to +125C Package: MF ML MS ST UN = = = = = Plastic Dual Flat No-lead (3x3 DFN), 8/10-lead Plastic Quad Flat No-lead (QFN), 16-lead Plastic Micro Small Outline (MSOP), 8-lead Plastic Thin Shrink Small Outline (TSSOP), 14-lead Plastic Micro Small Outline (MSOP), 10-lead (c) 2008 Microchip Technology Inc. Examples: a) b) c) d) e) MCP4531-502E/XX: MCP4531-103E/XX: MCP4531-503E/XX: MCP4531-104E/XX: MCP4531T-104E/XX: 5 k, 8LD Device 10 k, 8-LD Device 50 k, 8LD Device 100 k, 8LD Device T/R, 100 k, 8LD Device a) b) c) d) e) MCP4532-502E/XX: MCP4532-103E/XX: MCP4532-503E/XX: MCP4532-104E/XX: MCP4532T-104E/XX: 5 k, 8LD Device 10 k, 8-LD Device 50 k, 8LD Device 100 k, 8LD Device T/R, 100 k, 8LD Device a) b) c) d) e) MCP4551-502E/XX: MCP4551-103E/XX: MCP4551-503E/XX: MCP4551-104E/XX: MCP4551T-104E/XX: 5 k, 8LD Device 10 k, 8-LD Device 50 k, 8LD Device 100 k, 8LD Device T/R, 100 k, 8LD Device a) b) c) d) e) MCP4552-502E/XX: MCP4552-103E/XX: MCP4552-503E/XX: MCP4552-104E/XX: MCP4552T-104E/XX: 5 k, 8LD Device 10 k, 8-LD Device 50 k, 8LD Device 100 k, 8LD Device T/R, 100 k, 8LD Device a) b) c) d) e) MCP4631-502E/XX: MCP4631-103E/XX: MCP4631-503E/XX: MCP4631-104E/XX: MCP4631T-104E/XX: 5 k, 8LD Device 10 k, 8-LD Device 50 k, 8LD Device 100 k, 8LD Device T/R, 100 k, 8LD Device a) b) c) d) e) MCP4632-502E/XX: MCP4632-103E/XX: MCP4632-503E/XX: MCP4632-104E/XX: MCP4632T-104E/XX: 5 k, 8LD Device 10 k, 8-LD Device 50 k, 8LD Device 100 k, 8LD Device T/R, 100 k, 8LD Device a) b) c) d) e) MCP4651-502E/XX: MCP4651-103E/XX: MCP4651-503E/XX: MCP4651-104E/XX: MCP4651T-104E/XX: 5 k, 8LD Device 10 k, 8-LD Device 50 k, 8LD Device 100 k, 8LD Device T/R, 100 k, 8LD Device a) b) c) d) e) MCP4652-502E/XX: MCP4652-103E/XX: MCP4652-503E/XX: MCP4652-104E/XX: MCP4652T-104E/XX: 5 k, 8LD Device 10 k, 8-LD Device 50 k, 8LD Device 100 k, 8LD Device T/R, 100 k, 8LD Device XX = = = = = MF for 8/10-lead 3x3 DFN ML for 16-lead QFN MS for 8-lead MSOP ST for 14-lead TSSOP UN for 10-lead MSOP DS22096A-page 85 MCP453X/455X/463X/465X NOTES: DS22096A-page 86 (c) 2008 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC, SmartShunt and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM, PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2008, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2008 Microchip Technology Inc. DS22096A-page 87 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-4182-8400 Fax: 91-80-4182-8422 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 01/02/08 DS22096A-page 88 (c) 2008 Microchip Technology Inc.