General Description
The MAX2320/MAX2321/MAX2322/MAX2324/MAX2326/
MAX2327 evaluation kits (EV kits) simplify evaluation of
these high-linearity, silicon germanium (SiGe), dual-
band LNAs/mixers. They enable testing of the devices’
RF performance and require no additional support cir-
cuitry. The signal inputs and outputs use SMA connec-
tors to simplify the connection of RF test equipment.
The MAX2320/21/22/24/26/27 EV kits are assembled
with an associated IC and incorporate input and output
matching components optimized for the 869MHz to
894MHz cellular frequency band, 1930MHz to
1990MHz PCS frequency band, 210MHz digital mixer
output frequency, and 110MHz FM mixer output fre-
quency. All matching components may be changed to
work at other frequencies within the bands specified in
the MAX2320/21/22/24/26/27 data sheet.
Features
♦50ΩSMA Ports for Easy Testing
♦+2.7V to +3.6V Single-Supply Operation
♦All Critical Matching Components Included
♦Fully Assembled and Tested
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
________________________________________________________________ Maxim Integrated Products 1
19-1535; Rev 1; 6/00
PART
MAX2320EVKIT -40°C to +85°C
TEMP. RANGE IC PACKAGE
20 TSSOP-EP*
For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
Ordering Information
MAX2321EVKIT -40°C to +85°C 20 TSSOP-EP
MAX2322EVKIT
MAX2324EVKIT -40°C to +85°C 20 TSSOP-EP
-40°C to +85°C 20 TSSOP-EP
MAX2326EVKIT
MAX2327EVKIT -40°C to +85°C 20 TSSOP-EP
-40°C to +85°C 20 TSSOP-EP
2.7pF ±0.1pF ceramic cap (0603)
Murata GRM39COG2R7B50V
1C2
6800pF ±5% ceramic caps (0603)
Murata GRM39X7R682J50V
4
C4, C5,
C8, C34
100pF ±5% ceramic caps (0603)
Murata GRM39COG101J50V
6
C6, C11, C15,
C18, C20, C28
0.033µF ±10% ceramic cap (0603)
Murata GRM39X7R333K50V
1C9
10µF ±20%,16V tantalum capacitor
AVX TAJB106M016 or
Sprague 293D106X0010B
1C12
4.7pF ±0.1pF ceramic cap (0402)
Murata GRM36COG4R7B50V
1C10
22pF ±5% ceramic caps (0603)
Murata GRM39COG220J50V
2C7, C17
0.01µF ±5% ceramic caps (0603)
Murata GRM39X7R103J50V
4
C16, C19, C21,
C22
3.3pF ±0.1pF ceramic caps (0603)
Murata GRM39COG3R3B50V or
3.3pF ±0.25pF ceramic caps (0603)
Murata GRM39COG3R3C50V
3C13, C14, C23
DESIGNATION
1.0pF ±0.1pF ceramic caps (0603)
Murata GRM39COG010B50V
2C1, C32
DESCRIPTIONQTY
MAX2320/21/26/27 EV Kits
Component List
SUPPLIER PHONE FAX
AVX 803-946-0690 803-626-3123
Coilcraft 847-639-6400 803-639-1469
EFJohnson 402-474-4800 402-474-4858
Kamaya 219-489-1533 219-489-2261
Murata
Electronics 800-831-9172 814-238-0490
Sprague 603-224-1961 603-224-1430
URL
www.
avxcorp.com
www.
coilcraft.com
www.
efjohnson.com
www.
kamaya.com
www.
murata.com
www.
vishay.com
Toko 408-432-8281 408-943-9790 www.
toko.com
Component Suppliers
*EP = Exposed paddle
1000pF ±5% ceramic caps (0603)
Murata GRM39X7R102J50V
5C24–C27, C29
1.5pF ±0.1pF ceramic cap (0603)
Murata GRM39COG1R5B50V
1C31
18pF ±5% ceramic cap (0603)
Murata GRM39COG1180J50V
1C35
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
2 _______________________________________________________________________________________
MAX2320/21/26/27 EV Kits Component List (continued)
6.8nH ±5% inductor (0603)
Murata LQG11A6N8J00
1L2
330nH ±5% inductor (1008)
Coilcraft 1008CS-331XJBC
1L3
3.85nH ±10% inductor
Coilcraft 0906-4-10
1L6
5.6nH ±0.5nH inductor (0603)
Murata LQW1608A5N6D00
1L8
4.7nH ±0.3nH inductor (0603)
Toko LL1608-FH4N7S
1L7
110nH ±5% inductors (0603)
Coilcraft 0603CS-R11XJBC
2L4, L5
20kΩ±5% resistor (0603)
Kamaya RMC16-203JT
1R2
DESIGNATION
1.8nH ±10% inductor (0603)
Coilcraft 0603CS-1N8XKBC
1L1
DESCRIPTIONQTY DESIGNATION
51Ω±5% resistors (0603)
Kamaya RMC16-51RJT
2R3, R4
DESCRIPTIONQTY
1.65nH air core
Coilcraft 0906-2
1L10
20kΩ±5% resistor (0402)
Kamaya RMC16S-203JT
1
Not installed—
MAX2320/
26/27
8.2nH ±5% inductor (0603)
Murata LQG11A8N2J00
1MAX2321
MAX2320/
26/27
MAX2327 Not installed—
R1
GND, VCC 2Test points
JU1–JU4, JU6 53-pin headers
JU5, JU8 22-pin headers
None 7Shunts (JU1–JU6, JU8)
1MAX2320EUP, 20-pin TSSOP-EPMAX2320
1MAX2321EUP, 20-pin TSSOP-EPMAX2321
U1
1MAX2327EUP, 20-pin TSSOP-EP
1MAX2326EUP, 20-pin TSSOP-EP
MAX2327
MAX2326
L9
SMA connectors (PC edge mount)
EFJohnson 142-0701-801
12
LNAINH, LNAOUTH,
LNAINL, LNAOUTL,
LOLIN, LOHIN,
LOOUTH, LOOUTL,
FMOUT, CDMAOUT,
MIXINL, MIXINH
8.2kΩ±5% resistor (0603)
Kamaya RMC16-822JT
1R9
Balun transformer (B5F type)
Toko 458DB-1011
1T1
1kΩ±5% resistors (0603)
Kamaya RMC16-102JT
4R6, R7, R8, R10
2kΩ±5% resistor (0603)
Kamaya RMC16-202JT
1R5
30Ω±5% resistor (0603)
Kamaya RMC16-30RJT
1R11
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
_______________________________________________________________________________________ 3
MAX2322 EV Kit Component List
Not installed—
C2, C3, C5, C6,
C9, C10, C18,
C22, C23, C30
22pF ±5% ceramic capacitors (0603)
Murata GRM39COG220J50V
2C7, C17
10µF ±20%, 16V, tantalum capacitor
AVX TAJB106M016 or
Sprague 293D106X0010B
1C12
0.01µF ±5% ceramic caps (0603)
Murata GRM39X7R103J50V
3C16, C19, C21
3.3pF ±0.1pF ceramic caps (0603)
Murata GRM39COG3R3B50V or
3.3pF ±0.25pF ceramic caps (0603)
Murata GRM39COG3R3C50V
2C13, C14
100pF ±5% ceramic caps (0603)
Murata GRM39COG101J50V
3C11, C15, C20
1.5pF ±0.1pF ceramic cap (0603)
Murata GRM39COG1R5B50V
1C31
Not installed—
L2, L3, L6,
L7, L9
1.8nH ±10% inductor (0603)
Coilcraft 0603CS-1N8XKBC
1L1
1000pF ±5% ceramic caps (0603)
Murata GRM39X7R102J50V
6C24–C29
DESIGNATION
1.0pF ±0.1pF ceramic caps (0603)
Murata GRM39COG010B50V
2C1, C32
DESCRIPTIONQTY
Not installed—R4
1kΩ±5% resistors (0603)
Kamaya RMC16-102JT
4
R6, R7, R8,
R10
2kΩ±5% resistor (0603)
Kamaya RMC16-202JT
1R5
SMA connectors (PC edge mount)
EFJohnson 142-0701-801
6
LNAINH,
LNAOUTH,
LOHIN,
LOOUTH,
CDMAOUT,
MIXINH
3-pin headers5JU1–JU4, JU6
Test points2GND, VCC
Balun transformer (B5F type)
Toko 458DB-1011
1T1
Shunts (JU1–JU6, JU8)7None
MAX2322EUP, 20-pin TSSOP-EP1U1
2-pin headers2JU5, JU8
DESIGNATION
5.6nH ±0.5nH inductor (0603)
Murata LQW1608A5N6D00
1L8
DESCRIPTIONQTY
33pF ±5% ceramic capacitor (0402)
Murata GRM36COG330J50V
1C33
110nH ±5% inductors (0603)
Coilcraft 0603CS-R11XJBC
2L4, L5
0Ωresistor
Kamaya RMC16-0R0JT
1C9
8.2kΩ±5% resistor (0603)
Kamaya RMC16-822JT
1R9
51Ω±5% resistor (0603)
Kamaya RMC16-51RJT
1R3
20kΩ±5% resistor (0603)
Kamaya RMC16-203JT
1R2
20kΩ±5% resistor (0402)
Kamaya RMC16S-203JT
1R1
1.65nH air core
Coilcraft 0906-2
1L10
6800pF ±5% ceramic caps (0603)
Murata GRM39X7R082J50V
20C4, C8
30Ω±5% resistor (0603)
Kamaya RMC16-30RJT
1R11
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
4 _______________________________________________________________________________________
MAX2324 EV Kit Component List
2.7pF ±0.1pF ceramic cap (0603)
Murata GRM39COG2R7B50V
1C2
0.033µF ±10% ceramic cap (0603)
Murata GRM39X7R333K50V
1C9
100pF ±5% ceramic caps (0603)
Murata GRM39COG101J50V
5
C6, C11, C15,
C18, C28
10µF ±20%, 16V, tantalum capacitor
AVX TAJB106M016 or
Sprague 293D106X0010B
1C12
0.01µF ±5% ceramic capacitors (0603)
Murata GRM39X7R103J50V
3C16, C19, C22
3.3pF ±0.1pF ceramic caps (0603)
Murata GRM39COG3R3B50V or
3.3pF ±0.25pF ceramic caps (0603)
Murata GRM39COG3R3C50V
3C13, C14, C23
4.7pF ±0.1pF ceramic cap (0402)
Murata GRM36COG4R7B50V
1C10
6.8nH ±5% inductor (0603)
Murata LQG11A6N8J00
1L2
Not installed—L1, L7, L8, L9
1000pF ±5% ceramic capacitors (0603)
Murata GRM39X7R102J50V
5C24–C27, C29
DESIGNATION
Not installed—
C1, C4, C7, C8,
C17, C20, C21,
C31, C32, C33
DESCRIPTIONQTY
51Ω±5% resistor (0603)
Kamaya RMC16-51RJT
1R4
1kΩ±5% resistors (0603)
Kamaya RMC16-102JT
4
R6, R7, R8,
R10
2kΩ±5% resistor (0603)
Kamaya RMC16-202JT
1R5
Balun transformer (B5F type)
Toko 458DB-1011
1T1
Test points2GND, VCC
SMA connectors (PC edge mount)
EFJohnson 142-0701-801
7
LNAINL,
LNAOUTL,
LOLIN,
LOOUTL,
FMOUT,
CDMAOUT,
MIXINL
8.2kΩ±5% resistor (0603)
Kamaya RMC16-8252JT
1R9
2-pin headers2JU5, JU8
MAX2324EUP, 20-pin TSSOP-EP1U1
Shunts (JU1–JU6, JU8)7None
3-pin headers5JU1–JU4, JU6
DESIGNATION DESCRIPTIONQTY
330nH ±5% inductor (1008)
Coilcraft 1008CS-331XJBC
1L3
110nH ±5% inductors
Coilcraft 0603CS-R11XJBC
2L4, L5
3.85nH ±10% inductor
Coilcraft 0906-4-10
1L6
4.7nH ±0.3nH inductor (0603)
Toko LL1608-FH4N7S
1L10
Not installed—R3
20kΩ±5% resistor (0603)
Kamaya RMC16-203JT
1R2
20kΩ±5% resistor (0402)
Kamaya RMCS16S-203JT
1R1
6800pF ±5% ceramic caps (0603)
Murata GMR39X7R682J50V
2C5, C30
18pF ±5% ceramic capacitor (0603)
Murata GRM39COG180J50V
1C35
30Ω±5% resistor (0603)
Kamaya RMC16-30RJT
1R11
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
_______________________________________________________________________________________ 5
_________________________________Quick Start
The MAX2320/21/22/24/26/27 EV kits are fully assem-
bled and factory tested. Follow the instructions in the
Connections and Setup section for proper device eval-
uation. Figures 1, 2, and 3 show the schematics.
Figures 4 through 9 are component placement guides
and PC board layouts.
Test Equipment Required
The adjacent table lists the required test equipment to
verify MAX2320/MAX2321/MAX2322/MAX2324/MAX2326/
MAX2327 operation. It is intended as a guide only, and
some substitutions are possible.
Connections and Setup
This section provides a step-by-step guide to operating
the EV kits and testing the devices’ functions. Do not
turn on DC power or RF signal generators until all con-
nections are made.
Testing the LNA
1) Connect a DC supply set to +2.7V (through an
ammeter if desired) to the VCC and GND terminals
on the EV kit. If available, set the current limit to
40mA.
2) Install the shunts across jumpers JU5 and JU8.
Install the shunt across JU6 to the FMMXR position
and across JU4 to the OFF position. See Tables 1–5
for positions of the shunts across JU1, JU2, and JU3
for different modes.
Table 1. MAX2320/MAX2321/MAX2326 Mode Selection
PCS band, high gain, low linearityHGAINLLINPCS
PCS band, low gain, high linearity
PCS band, high gain, high linearity
Cellular band FM
Cellular band, high gain, low linearity
Cellular band, low gain, high linearity
Cellular band, high gain, high linearity
MODE
LGAINHLINPCS
HGAINHLINPCS
LGAINLLINCELL
HGAINLLINCELL
LGAINHLINCELL
HGAINHLINCELL
JU3 SHUNT
POSITION
JU1 SHUNT
POSITION
JU2 SHUNT
POSITION
ShutdownLGAINLLINPCS
Table 2. MAX2322 Mode Selection
Not used
PCS band, high gain, low linearity
PCS band, low gain, high linearity
PCS band, high gain, high linearity
Shutdown
MODE
LGAINLLINCELL
HGAINLLINCELL
LGAINHLINCELL
HGAINHLINCELL
Don’t careDon’t carePCS
JU3 SHUNT
POSITION
JU1 SHUNT
POSITION
JU2 SHUNT
POSITION*
*JU2 is connected to the MAX2322
SHDN
pin.
EQUIPMENT DESCRIPTION
Capable of delivering at least 0dBm of
output power up to 2.5GHz (HP 8648C
or equivalent)
RF Signal
Generators
Capable of covering the operating
frequency range of the devices as well
as a few harmonics (HP 8561E, for
example)
Capable of up to 100mA at +2.7V to
+3.6V
RF Spectrum
Analyzer
For measuring the supply current
(optional)
To measure small-signal return
loss and gain (optional, HP 8753D,
for example)
Power Supply
Ammeter
Network Analyzer
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
6 _______________________________________________________________________________________
15
14
13
12
11
MAX2320
MAX2321
MAX2326
MAX2327
U1
FMOUT
BUFFEN
VCC
VCC
MIXINL
20
MIXINH
LOLOUT
1
3
9
10 LOHIN
LNAOUTH
JU2
JU5
JU1
JU3
2LNAOUTL
RLNA (N.C.)
LNAINH
4
LNAINL
5
6
7
8GAIN (MODE)
( ) ARE FOR MAX2327 ONLY
*MAX2321 ONLY
VCC
VCC
VCC
VCC
VCC
LOHOUT
JU6
JU4
1
2
SMA
LOOUTH
VCC
VCC
GND
LOLIN
LIN (SHDN)
BAND
VCC
SMA
LOOUTL
SMA
FMOUT
SMA
LNAOUTL
SMA
LNAINH
SMA
LNAOUTH
SMA
LNAINL
L6
3.85nH
L2
6.8nH
L1
1.8nH
SMA
LOLIN
SMA
LOHIN
SMA
MIXINH
C27
1000pF C29
1000pF
C18
100pF
C17
22pF
R4
51Ω
R3
51ΩC15
100pF
C28
1000pF
C28
100pF
C32
1pF
C24
1000pF
C26
1000pF
C25
1000pF
C22
0.01µF
C21
0.01µF
C20
100pF
C31
1.5pF
C11
100pF
C10
4.7pF
C12
10µF
16V
C7
22pF
C2
2.7pF
C6
100pF
C1
1pF
C5
6800pF
R6
1k
R7
1k
R8
1k
C34
6800pF
C8
6800pF
L8
5.6nH
R9
8.2k
R10
1k
L3
330nH
L9
OPEN
8.2nH*
RBIAS 18
R2
20k
19 SMA
MIXINL
C30
OPEN
L7
4.7nH
C9
0.033µF
C23
3.3pF
VCC
17
16
CDMA- (IFOUT-)
T1
CDMA+ (IFOUT+) 1
2
6
34
SMA
CDMAOUT
C14
3.3pF
C13
3.3pF
R5
2k
VCC
C16
0.01µFC19
0.01µF
L4
110nH
L5
110nH
R1
20k (OPEN) JU8
C4
6800pF L10
1.65nH
C35
18pF
R11
30Ω
Figure 1. MAX2320/21/26/27 EV Kits Schematic
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
_______________________________________________________________________________________ 7
15
14
13
12
11
MAX2322
U1
LOX2
N.C.
N.C. N.C.
BUFFEN
VCC
20
MIXINH
N.C.
1
3
9
10 LOHIN
LNAOUTH
JU2
JU1
JU3
2
RLNA
LNAINH
4
6
5
7
8GAIN
VCC
VCC
VCC
VCC
LOHOUT
JU4
1
2
SMA
LOOUTH
VCC
VCC
GND
N.C.
LIN
VCC
SMA
LNAINH
SMA
LNAOUTH
L1
1.8nH
SMA
LOHIN
SMA
MIXINH
C27
1000pF
C17
22pF
R3
51ΩC15
100pF
C28
1000pF
C32
1pF
C24
1000pF
C26
1000pF
C25
1000pF
C20
100pF
C31
1.5pF
C11
100pF
C12
10µF
16V
C7
22pF
C4
6800pF
C1
1pF
R1
20k
R6
1k
R7
1k
R8
1k
C33
33pF
C8
6800pF
L8
5.6nH
R10
1k
L9
OPEN
RBIAS 18
R2
20k
19
VCC
17
16
CDMA-
T1
CDMA+ 1
2
6
34
SMA
CDMAOUT
C14
3.3pF
C13
3.3pF
R5
2k
VCC
C16
0.01µFC19
0.01µF
L4
110nH
L5
110nH
SHDN
L10
1.65nH
JU6
C29
1000pF
R9
8.2k
VCC
JU5
VCC
C21
0.01µF
R11
30Ω
JU8
Figure 2. MAX2322 EV Kit Schematic
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
8 _______________________________________________________________________________________
15
14
13
12
11
MAX2324
U1
FMOUT
BUFFEN
VCC
VCC
MIXINL
20
N.C.
LOLOUT
1
3
9
10 N.C.
N.C.
JU2
JU1
JU3
2LNAOUTL
RLNA
MODEOUT
4
LNAINL
5
6
7
8GAIN
VCC
VCC
VCC
VCC
N.C.
JU6
JU4
1
2
VCC
VCC
GND
LOLIN
LIN
VCC
SMA
LOOUTL
SMA
FMOUT
SMA
LNAOUTL
SMA
LNAOUTH
SMA
LNAINL
L6
3.85nH
L2
6.8nH
L1
OPEN
SMA
LOLIN
C27
1000pF C29
1000pF
C18
100pF
R4
51Ω
C15
100pF
C28
100pF
C28
100pF
C24
1000pF
C26
1000pF
C25
1000pF
C22
0.01µF
C20
OPEN
C11
100pF
C10
4.7pF
C12
10µF
16V
C2
2.7pF
C6
100pF
C1
OPEN
C5
6800pF
R6
1k
R7
1k
R8
1k
C30
6800pF
R9
8.2k
R10
1k
L3
330nH
RBIAS 18
R2
20k
19 SMA
MIXINL
C9
0.033µF
L7
OPEN L10
4.7nH
C23
3.3pF
VCC
17
16
CDMA-
T1
CDMA+ 1
2
6
34
SMA
CDMAOUT
C14
3.3pF
C13
3.3pF
R5
2k
VCC
C16
0.01µFC19
0.01µF
L4
110nH
L5
110nH
SHDN
C35
18pF
JU5
VCC
C21
OPEN
R11
30Ω
R1
20K JU8
Figure 3. MAX2324 EV Kit Schematic
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
_______________________________________________________________________________________ 9
3) Connect one RF signal generator to the LNAINL
(LNAINH) SMA connector for cellular (PCS) band
testing. Do not turn on the generator’s output. Set
the generator for an output frequency of 881MHz
(1960MHz) for cellular (PCS) band operation. Set
the power level to -25dBm.
4) Connect the spectrum analyzer to the LNAOUTL
(LNAOUTH) SMA connector for cellular (PCS) band.
Set the center frequency to 881MHz (1960MHz) for
cellular (PCS) band, and span to 5MHz.
5) Turn on the RF signal generator. The peak that
appears on the spectrum analyzer should have a
magnitude of about -11dBm in high-gain and FM
modes. In low-gain modes, the magnitude should
be about -27dBm. Be sure to account for cable
losses (between 0.5dB and 2dB) and circuit board
losses (approximately 0.5dB) when computing gain
and noise figure.
6) (Optional) Another method for determining gain is
by using a network analyzer. This has the advan-
tage of displaying gain over a swept frequency
band, in addition to displaying input and output
return loss. Refer to the network analyzer manufac-
turer’s user manual for setup details.
Testing the Mixer
1) Connect a DC supply set to +2.7V (through an
ammeter if desired) to the VCC and GND terminals
on the EV kit. If available, set the current limit to
40mA.
2) Install the shunts across jumpers JU5 and JU8.
Install the shunt across JU6 to the FMMXR position
(except MAX2322; see Table 5) and across JU4 to
OFF. See Tables 1–4 for positions of the shunts
across JU1, JU2, and JU3 for different modes.
3) Connect an RF signal generator to the MIXINL (MIX-
INH) SMA connector for cellular (PCS) band testing.
Do not turn on the generator’s output. Set the gener-
ator for an output frequency of 881MHz (1960MHz)
for cellular (PCS). Set the power level to -25dBm.
4) See Table 5, and connect the second RF signal gen-
erator to the appropriate LO connector and set the
frequency accordingly. Set the power level to
-6dBm.
5) In FM mode, connect the spectrum analyzer con-
nector to the FMOUT SMA, set the center frequency
to 110MHz, and span to 5MHz. For all other modes,
connect the spectrum analyzer connector to the
CDMAOUT SMA and set the center frequency to
210MHz and span to 5MHz.
FM
Cellular band, high gain, low linearity
Cellular band, low gain, high linearity
Cellular band, high gain, high linearity
Shutdown
MODE
LGAINLLINCELL
HGAINLLINCELL
LGAINHLINCELL
HGAINHLINCELL
Don’t careDon’t carePCS
JU3 SHUNT
POSITION
JU1 SHUNT
POSITION
JU2 SHUNT
POSITION*
Table 3. MAX2324 Mode Selection
*JU2 is connected to the MAX2324
SHDN
pin.
Table 4. MAX2327 Mode Selection
Not used
PCS band, digital mixer output
Cellular band, FM
Cellular band, digital mixer output
Shutdown
MODE
LGAINHLINPCS
HGAINHLINPCS
LGAINHLINCELL
HGAINHLINCELL
Don’t careLLINDon’t care
JU3 SHUNT
POSITION
JU1 SHUNT
POSITION*
JU2 SHUNT
POSITION
*JU1 is connected to the MAX2327
SHDN
pin.
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
10 ______________________________________________________________________________________
Table 5. LO Connector and LO Input Frequency Selection
991LOINLMAX2321 FM
1091LOINHMAX2321 Cellular
1750LOINHMAX2320/MAX2327 PCS
991LOINLMAX2320/MAX2327 FM
1091LOINLMAX2320/MAX2327 Cellular
LO INPUT FREQUENCY (MHz)LO CONNECTORDEVICE AND BAND OF OPERATION
991LOINLMAX2324 FM
1091LOINLMAX2324 Cellular
1085LOINHMAX2322 PCS, JU6 shunt at FMMXR position
1750LOINHMAX2322 PCS, JU6 shunt at LOX2N position
1085LOINHMAX2321 PCS
991LOINLMAX2326 FM
2182LOINHMAX2326 Cellular
2170LOINHMAX2326 PCS
6) Turn on both RF signal generators. In FM mode, the
spectrum analyzer should read about -15dBm at
110MHz. In all other modes, the peak should be
about -13dBm at 210MHz. Be sure to account for
cable losses (between 0.5dB and 2dB) and circuit
board losses (approximately 0.5dB) when comput-
ing gain and noise figure.
Layout
The EV kit PC board can serve as a guide for layout
using the MAX2320/21/22/24/26/27.
Keep traces carrying RF signals as short as possible to
minimize radiation and insertion loss due to the PC
board. Keep the differential mixer output traces togeth-
er and of equal length to ensure signal amplitude bal-
ance. Solder the entire bottom side slug evenly to the
board ground plane for best RF performance. Run the
input trace to the PCS LNA on the top layer of the PC
board avoiding via-induced coupling. Minimize the par-
allel length of the cellular LNA input trace with the PCS
LNA input trace.
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
______________________________________________________________________________________ 11
1.0"1.0"
1.0"
1.0"
Figure 6. MAX2320/21/22/24/26/27 EV Kits PC Board Layout—
Component Side
Figure 7. MAX2320/21/22/24/26/27 EV Kits PC Board Layout—
Ground Plane 2
Figure 4. MAX2320/21/22/24/26/27 EV Kits Component
Placement Guide—Component Side
Figure 5. MAX2320/21/22/24/26/27 EV Kits Component
Placement Guide—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2000 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
Evaluate: MAX2320/21/22/24/26/27
MAX2320/21/22/24/26/27 Evaluation Kits
1.0"1.0"
Figure 8. MAX2320/21/22/24/26/27 EV Kits PC Board Layout—
Ground Plane 3
Figure 9. MAX2320/21/22/24/26/27 EV Kits PC Board Layout—
Solder Side
