19-3954; Rev 4; 7/09 KIT ATION EVALU E L B A AVAIL 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance Features The MAX9242/MAX9244/MAX9246/MAX9254 deserialize three LVDS serial-data inputs into 21 single-ended LVCMOS/LVTTL outputs. A separate parallel-rate LVDS clock provides the timing for deserialization. The MAX9242/ MAX9244/MAX9246/MAX9254 feature spread-spectrum capability, allowing the output data and clock frequency to spread over a specified range to reduce EMI. The single-ended data and clock outputs are programmable for a frequency spread of 2%, 4%, or no spread. The spread-spectrum function is also available when the MAX9242/MAX9244/MAX9246/MAX9254 operate in nonDC-balanced mode. The modulation rate of the spread is 32kHz for a 33MHz LVDS clock input and scales linearly with frequency. The single-ended outputs have a separate supply, allowing +1.8V to +5V output logic levels. Programmable 4%, 2%, or OFF Spread-Spectrum Output for Reduced EMI Programmable DC-Balanced or Non-DC-Balanced Modes DC Balance Allows AC-Coupling for Wider Input Common-Mode Voltage Range Spread Spectrum Operates in DC-Balanced or Non-DC-Balanced Mode High Output Drive (MAX9254) / 4 Deskew by Oversampling (MAX9242/MAX9244/MAX9254) 16MHz-to-34MHz (DC-Balanced) and 20MHz-to40MHz (Non-DC-Balanced) Operation (MAX9242/MAX9244/MAX9254) 6MHz-to-18MHz (DC-Balanced) and 8MHz-to-20MHz (Non-DC-Balanced) Operation (MAX9246) Rising-Edge (MAX9242) or Falling-Edge (MAX9244/MAX9246/MAX9254) Output Strobe High-Impedance Outputs when PWRDWN is Low Allow Output Busing Separate Output Supply Allows Interface to +1.8V, +2.5V, +3.3V, and +5V Logic LVDS Inputs Meet ISO 10605 ESD Protection at 30kV Air-Gap Discharge and 6kV Contact Discharge LVDS Inputs Meet IEC 61000-4-2 Level 4 ESD Protection at 15kV Air-Gap Discharge and 8kV Contact Discharge LVDS Inputs Conform to ANSI TIA/EIA-644 Standard +3.3V Main Power Supply The MAX9254 features high output drive current for both data and clock outputs for faster transition times in the presence of heavy capacitive loads. The MAX9242/MAX9244/MAX9246/MAX9254 feature programmable DC balance, allowing isolation between a serializer and deserializer using AC-coupling. The MAX9242/MAX9244/MAX9246/MAX9254 operate with the MAX9209/MAX9213 serializers and are available with a rising-edge strobe (MAX9242) or falling-edge strobe (MAX9244/MAX9246/MAX9254). The LVDS inputs meet ISO 10605 ESD specifications with 30kV Air-Gap Discharge and 6kV Contact Discharge ratings. Applications Automotive Navigation Systems Automotive DVD Entertainment Systems Ordering Information Digital Copiers PART Laser Printers Selector Guide FREQUENCY RANGE STROBE EDGE OVERSAMPLING NON-DC BALANCE (MHz) DC BALANCE (MHz) MAX9242 Rising Yes 20 to 40 16 to 34 MAX9244 Falling Yes 20 to 40 16 to 34 MAX9246 Falling No 8 to 20 6 to 18 MAX9254 Falling Yes 20 to 40 16 to 34 PART Pin Configuration appears at end of data sheet. TEMP RANGE PIN-PACKAGE MAX9242EUM -40C to +85C 48 TSSOP MAX9242EUM/V+ -40C to +85C 48 TSSOP MAX9242GUM -40C to +105C 48 TSSOP MAX9242GUM/V+ -40C to +105C 48 TSSOP MAX9244EUM -40C to +85C 48 TSSOP MAX9244EUM/V+ -40C to +85C 48 TSSOP -40C to +105C 48 TSSOP MAX9244GUM MAX9244GUM/V+ -40C to +105C 48 TSSOP +Denotes a lead(Pb)-free/RoHS-compliant package. /V denotes an automotive qualified part. Note: All devices are available in lead(Pb)-free/RoHS-compliant packaging. Specify lead(Pb)-free/RoHS compliant by adding a + symbol at the end of the part number when ordering. Ordering Information continued at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX9242/MAX9244/MAX9246/MAX9254 General Description MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance ABSOLUTE MAXIMUM RATINGS (All voltages referenced to GND.) VCC, LVDSVCC, PLLVCC .......................................-0.5V to +4.0V VCCO......................................................................-0.5V to +6.0V RxIN__, RxCLKIN_.................................................-0.5V to +4.0V PWRDWN ..............................................................-0.5V to +6.0V SSG, DCB...................................................-0.5V to (VCC + 0.5V) RxOUT_, RxCLKOUT ...............................-0.5V to (VCCO + 0.5V) Continuous Power Dissipation (TA = +70C) 48-Pin TSSOP (derate 16mW/C above +70C) ........1282mW ESD Protection Human Body Model (RD = 1.5k, CS = 100pF) All Pins to GND .............................................................2.5kV IEC 61000-4-2 (RD = 330, CS = 150pF) LVDS Inputs to GND (Air-Gap Discharge).....................15kV LVDS Inputs to GND (Contact Discharge).......................8kV ISO 10605 (RD = 2.0k, CS = 330pF) LVDS Inputs to GND (Air-Gap Discharge).....................30kV LVDS Inputs to GND (Contact Discharge).......................6kV Operating Temperature Range .........................-40C to +105C Storage Temperature Range .............................-65C to +150C Junction Temperature ......................................................+150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (VCC = LVDSVCC = PLLVCC = +3.0V to +3.6V, VCCO = +3.0V to +5.5V, PWRDWN = high; SSG = high, open, or low; DCB = high or low, differential input voltage |VID| = 0.05V to 1.2V, input common-mode voltage VCM = |VID / 2| to 2.4V - |VID / 2|, unless otherwise noted. Typical values are at VCC = VCCO = LVDSVCC = PLLVCC = +3.3V, |VID| = 0.2V, VCM = +1.25V, TA = +25C.) (Notes 1, 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS POWER SUPPLY Power-Supply Range VCC, LVDSVCC, PLLVCC 3.0 3.6 V Output-Supply Range VCCO 1.8 5.5 V DC-balanced mode (SSG = low) Worst-Case Supply Current 2 ICCW CL = 8pF, worst-case pattern, VCC = VCCO = 3.0V to 3.6V, Figure 2 (MAX9242, MAX9244, MAX9254) Non-DC-balanced mode (SSG = low) 16MHz 50 68 34MHz 81 108 20MHz 55 73 33MHz 75 97 40MHz 83 110 DC-balanced mode 16MHz (SSG = high or open) 34MHz 62 85 101 135 20MHz 67 91 Non-DC-balanced 33MHz mode (SSG = high or open) 40MHz 93 123 107 134 _______________________________________________________________________________________ mA 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance (VCC = LVDSVCC = PLLVCC = +3.0V to +3.6V, VCCO = +3.0V to +5.5V, PWRDWN = high; SSG = high, open, or low; DCB = high or low, differential input voltage |VID| = 0.05V to 1.2V, input common-mode voltage VCM = |VID / 2| to 2.4V - |VID / 2|, unless otherwise noted. Typical values are at VCC = VCCO = LVDSVCC = PLLVCC = +3.3V, |VID| = 0.2V, VCM = +1.25V, TA = +25C.) (Notes 1, 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX 6MHz 29 45 8MHz 33 49 18MHz 48 69 47 DC-balanced mode (SSG = low) Worst-Case Supply Current ICCW Non-DC-balanced CL = 8pF, worst-case pattern, mode (SSG = low) VCC = VCCO = 3.0V to 3.6V, Figure 2 DC-balanced mode (MAX9246) (SSG = high or open) Non-DC-balanced mode (SSG = high or open) Power-Down Supply Current ICCZ 8MHz 33 10MHz 37 52 20MHz 52 73 6MHz 37 54 8MHz 41 62 18MHz 65 91 8MHz 41 58 10MHz 46 65 20MHz 66 92 PWRDWN = low 50 UNITS mA A 5V-TOLERANT LOGIC INPUT (PWRDWN) High-Level Input Voltage VIH 2.0 5.5 V Low-Level Input Voltage VIL -0.3 +0.8 V Input Current IIN PWRDWN = high or low level -20 +20 A ICL = -18mA -1.5 Input Clamp Voltage VCL V THREE-LEVEL LOGIC INPUTS (DCB, SSG) High-Level Input Voltage VIH Mid-Level Input Current IIM Low-Level Input Voltage VIL Input Current IIN Input Clamp Voltage VCL 2.5 VCC + 0.3 V -10 +10 A -0.3 +0.8 V DCB, SSG = high or low level, PWRDWN = high or low -20 +20 A ICL = -18mA -1.5 DCB, SSG open or connected to a driver with output in high-impedance state (Note 3) V SINGLE-ENDED OUTPUTS (RxOUT_, RxCLKOUT) VCCO - 0.1 IOH = -100A RxCLKOUT (Note 4) High-Level Output Voltage VOH RxOUT_ MAX9254 IOL = 100A VOL RxCLKOUT (Note 4) IOL = 2mA RxOUT_ V VCCO - 0.43 IOH = -2mA Low-Level Output Voltage VCCO - 0.25 MAX9254 VCCO - 0.25 0.1 0.2 0.26 0.2 V _______________________________________________________________________________________ 3 MAX9242/MAX9244/MAX9246/MAX9254 DC ELECTRICAL CHARACTERISTICS (continued) MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance DC ELECTRICAL CHARACTERISTICS (continued) (VCC = LVDSVCC = PLLVCC = +3.0V to +3.6V, VCCO = +3.0V to +5.5V, PWRDWN = high; SSG = high, open, or low; DCB = high or low, differential input voltage |VID| = 0.05V to 1.2V, input common-mode voltage VCM = |VID / 2| to 2.4V - |VID / 2|, unless otherwise noted. Typical values are at VCC = VCCO = LVDSVCC = PLLVCC = +3.3V, |VID| = 0.2V, VCM = +1.25V, TA = +25C.) (Notes 1, 2) PARAMETER SYMBOL High-Impedance Output Current IOZ Output Short-Circuit Current (Note 5) IOS Output Short-Circuit Current (MAX9254) (Note 5) IOS CONDITIONS MIN MAX UNITS -30 +30 A -10 -40 RxOUT_ -5 -20 RxCLKOUT (Note 4) -28 -75 RxOUT_ -13 -37 -16 -51 -34 -93 PWRDWN = low, VOUT = -0.3V to (VCCO + 0.3V) RxCLKOUT (Note 4) VCCO = 3.0V to 3.6V, VOUT = 0V VCCO = 4.5V to 5.5V, VOUT = 0V RxOUT_ VCCO = 3.0V to 3.6V, VOUT = 0V RxCLKOUT (Note 4) RxOUT_ VCCO = 4.5V to 5.5V, VOUT = 0V RxCLKOUT (Note 4) TYP mA mA LVDS INPUTS (RxIN__, RxCLKIN_) Differential Input High Threshold VTH (Note 6) Differential Input Low Threshold VTL (Note 6) -50 PWRDWN = high or low -25 +25 A A Input Current Power-Off Input Current Input Resistor 1 Input Resistor 2 IIN+, IIN- 50 IINO+, IINO- VCC = VCCO = 0V or open RIN1 RIN2 PWRDWN = high or low, VCC = VCCO = 0V or open, Figure 1 PWRDWN = high or low, VCC = VCCO = 0V or open, Figure 1 mV mV -40 +40 -40C to +85C 42 78 -40C to +105C 42 85 -40C to +85C 246 410 -40C to +105C 246 440 k k AC ELECTRICAL CHARACTERISTICS (VCC = LVDSVCC = PLLVCC = +3.0V to +3.6V, VCCO = +3.0V to +3.6V, CL = 8pF, PWRDWN = high; SSG = high, open, or low; DCB = high or low, differential input voltage |VID| = 0.1V to 1.2V, input common-mode voltage VCM = |VID / 2| to 2.4V - |VID / 2|, unless otherwise noted. Typical values are at VCC = VCCO = LVDSVCC = PLLVCC = +3.3V, |VID| = 0.2V, VCM = +1.25V, TA = +25C.) (Notes 6, 7, 8) PARAMETER SYMBOL CONDITIONS UNITS 2.9 4.7 6.5 2.0 3.3 4.1 RxOUT_ 2.1 3.0 4.2 RxCLKOUT 1.10 1.94 2.70 0.1 x VCCO to 0.9 x VCCO, Figure 3 RxOUT_ 1.4 2.2 3.3 ns 0.9 x VCCO to 0.1 x VCCO, Figure 3 RxCLKOUT 1.1 1.8 2.8 ns 2560 3142 0.1 x VCCO to 0.9 x VCCO, Figure 3 Output Fall Time CHLT 0.9 x VCCO to 0.1 x VCCO, Figure 3 Output Rise Time (MAX9254) CLHT Output Fall Time (MAX9254) CHLT DC-balanced mode, Figure 4 4 MAX RxOUT_ CLHT RSKM TYP RxCLKOUT Output Rise Time RxIN__ Skew Margin (Note 9) MIN 16MHz 34MHz 900 1386 Non-DC-balanced mode, 20MHz Figure 4 40MHz 2500 3164 960 1371 _______________________________________________________________________________________ ns ns ps 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance (VCC = LVDSVCC = PLLVCC = +3.0V to +3.6V, VCCO = +3.0V to +3.6V, CL = 8pF, PWRDWN = high; SSG = high, open, or low; DCB = high or low, differential input voltage |VID| = 0.1V to 1.2V, input common-mode voltage VCM = |VID / 2| to 2.4V - |VID / 2|, unless otherwise noted. Typical values are at VCC = VCCO = LVDSVCC = PLLVCC = +3.3V, |VID| = 0.2V, VCM = +1.25V, TA = +25C.) (Notes 6, 7, 8) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS RxCLKOUT High Time RCOH Figures 5a, 5b 0.35 x RCOP RxCLKOUT Low Time RCOL Figures 5a, 5b 0.35 x RCOP ns RxOUT_ Setup to RxCLKOUT RSRC Figures 5a, 5b 0.3 x RCOP ns RxOUT_ Hold from RxCLKOUT RHRC Figures 5a, 5b 0.45 x RCOP ns RxCLKIN_ to RxCLKOUT Delay RCCD SSG = low, Figures 6a, 6b Deserializer Phase-LockedLoop Set RPLLS Deserializer Power-Down Delay Deserializer Phase-LockedLoop Set from SSG Change 4.5 + 6.5 + 8.2 + (RCIP / 2) (RCIP / 2) (RCIP / 2) ns Figure 7 65,600 x RCIP ns RPDD Figure 8 100 ns RPLLS2 Figure 9 32,800 x RCIP ns SSG = high, Figure 10 Spread-Spectrum Output Frequency fRxCLKOUT SSG = open, Figure 10 SSG = low Spread-Spectrum Modulation Frequency ns fSSM Figure 10 Maximum output fRxCLKIN_ fRxCLKIN_ fRxCLKIN_ + 3.6% + 4.0% + 4.4% frequency Minimum output frequency fRxCLKIN_ fRxCLKIN_ fRxCLKIN_ - 4.4% - 4.0% - 3.6% Maximum output fRxCLKIN_ fRxCLKIN_ fRxCLKIN_ + 1.8% + 2.0% + 2.2% frequency Minimum output frequency MHz fRxCLKIN_ fRxCLKIN_ fRxCLKIN_ - 2.2% - 2.0% - 1.8% fRxCLKIN_ fRxCLKIN_ fRxCLKIN_ / 1016 Hz Note 1: Current into a pin is defined as positive. Current out of a pin is defined as negative. All voltages are referenced to ground, except VTH and VTL. Note 2: Maximum and minimum limits over temperature are guaranteed by design and characterization. Devices are production tested at TA = +25C. Note 3: To provide a mid level, leave the input open, or, if driven, put driver in high impedance. High-impedance leakage current must be less than 10A. Note 4: RxCLKOUT limits are scaled based on RxOUT_ measurements, design, and characterization data. Note 5: One output shorted at a time. Current out of the pin. Note 6: VTH, VTL, and AC parameters are guaranteed by design and characterization, and are not production tested. Limits are set at 6 sigma. Note 7: CL includes probe and test jig capacitance. Note 8: RCIP is the period of RxCLKIN_. RCOP is the period of RxCLKOUT. Note 9: RSKM is measured with less than 150ps cycle-to-cycle jitter on RxCLKIN_. _______________________________________________________________________________________ 5 MAX9242/MAX9244/MAX9246/MAX9254 AC ELECTRICAL CHARACTERISTICS (continued) MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance Test Circuits/Timing Diagrams VCC RIN2 FAIL-SAFE COMPARATOR RCOP RxIN_ + OR RxCLKIN+ RxIN_ + OR RxCLKIN+ RxCLKOUT VCC - 0.3V RIN1 RIN1 ODD RxOUT 1.2V EVEN RxOUT RIN1 RIN1 RxIN_ - OR RxCLKIN- RxIN_ - OR RxCLKIN- NON-DC-BALANCED MODE DC-BALANCED MODE Figure 2. Worst-Case Test Pattern Figure 1. LVDS Input Circuits 90% RxOUT_ OR RxCLKOUT 90% 10% RxOUT_ OR RxCLKOUT 10% 8pF CLHT CHLT Figure 3. Output Load and Transition Times IDEAL SERIAL BIT TIME 1.3V RCOP RxCLK OUT 2.0V 0.8V 1.1V RSKM RSKM IDEAL MIN IDEAL MAX RxOUT_ 2.0V 0.8V 2.0V 2.0V 0.8V RCOL RCOH RSRC RHRC 2.0V 0.8V INTERNAL STROBE Figure 4. LVDS Receiver Input Skew Margin 6 Figure 5a. Rising-Edge Output Setup/Hold and High/Low Times _______________________________________________________________________________________ 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance RCOP RCIP RxCLKOUT 2.0V 2.0V RxCLKIN_ 0.8V 0.8V RCOH RCOL RSRC RxOUT_ VID = 0V 0.8V RCCD RHRC 2.0V 0.8V 1.5V 2.0V 0.8V Figure 5b. Falling-Edge Output Setup/Hold and High/Low Times RxCLKOUT Figure 6a. Clock-IN to Clock-OUT Delay (MAX9244/MAX9246/ MAX9254) RCIP 2V + RxCLKIN_ PWRDWN VID = 0V - 3V RCCD VCC RPLLS RxCLKOUT 1.5V RxCLKIN_ Figure 6b. Clock-IN to Clock-OUT Delay (MAX9242) RxCLKOUT 1.5V HIGH IMPEDANCE PWRDWN 1.5V Figure 7. Phase-Locked-Loop Set Time RxCLKIN_ RPDD RxOUT_ RxCLKOUT 1.5V HIGH IMPEDANCE Figure 8. Power-Down Delay _______________________________________________________________________________________ 7 MAX9242/MAX9244/MAX9246/MAX9254 Test Circuits/Timing Diagrams (continued) MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance Test Circuits/Timing Diagrams (continued) 2.5V OPEN OR LESS THAN 10A LEAKAGE SSG 0.8V RPLLS2 RxCLKIN_ RxCLKOUT RxOUT_ TIMING SHOWN FOR FALLING-EDGE STROBE (MAX9244/MAX9246/MAX9254) PWRDWN = HIGH Figure 9. Phase-Locked-Loop Set Time from SSG Change FREQUENCY 1 / fSSM fRxCLKOUT (MAX) fRxCLKIN_ TIME fRxCLKOUT (MIN) Figure 10. Simplified Modulation Profile 8 _______________________________________________________________________________________ 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance 70 60 50 90 27 - 1 PRBS 40 WORST-CASE PATTERN 70 60 50 27 - 1 PRBS 20 25 30 35 40 WORST-CASE PATTERN 80 70 60 27 - 1 PRBS 50 40 30 30 15 15 20 25 30 35 15 40 20 25 30 40 35 FREQUENCY (MHz) FREQUENCY (MHz) FREQUENCY (MHz) WORST-CASE AND PRBS SUPPLY CURRENT vs. FREQUENCY (DC-BALANCED MODE, 4% SPREAD) RxOUT_ OUTPUT LOADING RxOUT_TRANSITION TIME vs. OUTPUT SUPPLY VOLTAGE (VCCO) DROPOUT (V) 80 70 60 3.2 3.1 3.0 27 - 1 PRBS 50 MAX9254 MAX9244 40 2.9 30 2.8 MAX9242 toc06 3.3 14 OUTPUT TRANSITION TIME (ns) WORST-CASE PATTERN MAX9242 toc05 90 3.4 MAX9242 toc04 100 SUPPLY CURRENT (mA) 80 40 30 90 SUPPLY CURRENT (mA) 80 100 MAX9242 toc02 WORST-CASE PATTERN SUPPLY CURRENT (mA) SUPPLY CURRENT (mA) 90 100 MAX9242 toc01 100 WORST-CASE AND PRBS SUPPLY CURRENT vs. FREQUENCY (DC-BALANCED MODE, 2% SPREAD) WORST-CASE AND PRBS SUPPLY CURRENT vs. FREQUENCY (DC-BALANCED MODE, NO SPREAD) MAX9242 toc03 WORST-CASE AND PRBS SUPPLY CURRENT vs. FREQUENCY (NON-DC-BALANCED MODE, NO SPREAD) 12 10 8 CLHT 6 4 2 CHLT 20 25 30 35 2.0 2.5 3.0 3.5 4.0 4.5 5.0 RxCLKOUT POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 33MHz, 4% SPREAD) -30 -40 -50 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB 33 FREQUENCY (MHz) 36 20 0 10 POWER SPECTRUM (dBm) POWER SPECTRUM (dBm) 10 -10 -20 -30 -40 -50 -60 -70 0 -10 -20 -30 -40 -50 -60 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB -70 -80 5.5 MAX9242 toc09 20 MAX9242 toc07 -20 30 1.5 RxCLKOUT POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 33MHz, 2% SPREAD) 0 -80 3 RxCLKOUT POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 33MHz, NO SPREAD) -10 -70 2 OUTPUT SUPPLY VOLTAGE (V) 10 -60 1 LOAD (mA) 20 POWER SPECTRUM (dBm) 0 40 FREQUENCY (MHz) MAX9242 toc08 15 0 -80 30 33 FREQUENCY (MHz) 36 30 33 36 FREQUENCY (MHz) _______________________________________________________________________________________ 9 MAX9242/MAX9244/MAX9246/MAX9254 Typical Operating Characteristics (VCC = PLLVCC = LVDSVCC = VCCO = +3.3V, CL = 8pF, PWRDWN = high, differential input voltage |VID| = 0.2V, input common-mode voltage VCM = 1.2V, TA = +25C, MAX9244/MAX9254, unless otherwise noted.) Typical Operating Characteristics (continued) (VCC = PLLVCC = LVDSVCC = VCCO = +3.3V, CL = 8pF, PWRDWN = high, differential input voltage |VID| = 0.2V, input common-mode voltage VCM = 1.2V, TA = +25C, MAX9244/MAX9254, unless otherwise noted.) RxCLKOUT POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 16MHz, 2% SPREAD) -20 -30 -40 -50 14 10 16 -10 -20 -30 -40 -50 -60 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB 16.5 0 10 -20 -30 -40 -50 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB -70 -80 -80 15.0 18.0 0 -10 -60 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB -70 16.5 18.0 15.0 16.5 FREQUENCY (MHz) FREQUENCY (MHz) FREQUENCY (MHz) RxOUT_ POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 16MHz, NO SPREAD) RxOUT_ POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 16MHz, 2% SPREAD) RxOUT_ POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 16MHz, 4% SPREAD) 10 POWER SPECTRUM (dBm) 0 10 -10 -20 -30 -40 -50 8 FREQUENCY (MHz) 0 -10 -20 -30 -40 -50 -60 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB 10 -80 7 8 FREQUENCY (MHz) 0 -10 -20 -30 -40 -50 -60 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB -70 9 20 18.0 MAX9242 toc18 20 MAX9242 toc16 20 18 20 POWER SPECTRUM (dBm) -50 7 14 MAX9242 toc15 20 MAX9242 toc13 -40 -80 -80 18 RxOUT_ POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 33MHz, 4% SPREAD) -30 -70 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB -70 RxOUT_ POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 33MHz, 2% SPREAD) -20 -60 -50 RxOUT_ POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 33MHz, NO SPREAD) -10 15.0 16 -40 FREQUENCY (MHz) POWER SPECTRUM (dBm) POWER SPECTRUM (dBm) -80 -30 -60 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB -70 -20 FREQUENCY (MHz) 0 -80 -50 0 -10 FREQUENCY (MHz) 10 -70 -40 18 16 20 -60 -30 POWER SPECTRUM (dBm) 14 -20 MAX9242 toc14 -80 -10 -60 RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB -70 10 MAX9242 toc17 -60 0 POWER SPECTRUM (dBm) -10 20 MAX9242 toc11 0 10 POWER SPECTRUM (dBm) POWER SPECTRUM (dBm) 10 10 20 MAX9242 toc10 20 RxCLKOUT POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 16MHz, 4% SPREAD) MAX9242 toc12 RxCLKOUT POWER SPECTRUM vs. FREQUENCY (RxCLKIN_ = 16MHz, NO SPREAD) POWER SPECTRUM (dBm) MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance RESOLUTION BW = 100kHz VIDEO BW = 100kHz ATTENUATION = 50dB -70 -80 9 7 8 FREQUENCY (MHz) ______________________________________________________________________________________ 9 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance PIN NAME FUNCTION 1 RxOUT17 2 RxOUT18 3, 25, 32, 38, 44 GND 4 RxOUT19 5 RxOUT20 6 SSG Three-Level-Logic, Spread-Spectrum Generator Control Input. SSG selects the frequency spread of RxCLKOUT relative to RxCLKIN_ (see Table 3). 7 DCB Three-Level-Logic, DC-Balance Control Input. DCB selects DC-balanced, non-DC-balanced, or reserved operation (see Table 1). 8 RxIN0- Channel 2 Single-Ended Outputs Ground Channel 2 Single-Ended Outputs Inverting Channel 0 LVDS Serial-Data Input 9 RxIN0+ Noninverting Channel 0 LVDS Serial-Data Input 10 RxIN1- Inverting Channel 1 LVDS Serial-Data Input 11 RxIN1+ Noninverting Channel 1 LVDS Serial-Data Input 12 LVDSVCC LVDS Supply Voltage. Bypass LVDSVCC to GND with 0.1F and 0.001F capacitors in parallel as close to the pin as possible. 13, 18 LVDSGND LVDS Ground 14 RxIN2- Inverting Channel 2 LVDS Serial-Data Input 15 RxIN2+ Noninverting Channel 2 LVDS Serial-Data Input 16 RxCLKIN- Inverting LVDS Parallel-Rate Clock Input 17 RxCLKIN+ 19, 21 PLLGND PLL Ground Noninverting LVDS Parallel-Rate Clock Input 20 PLLVCC PLL Supply Voltage. Bypass PLLVCC to GND with 0.1F and 0.001F capacitors in parallel as close to the pin as possible. 22 PWRDWN 5V-Tolerant LVTTL/LVCMOS Power-Down Input. PWRDWN is internally pulled down to GND. Outputs are high impedance when PWRDWN = low or open. 23 RxCLKOUT Parallel-Rate Clock Single-Ended Output. The MAX9242 has a rising-edge strobe. The MAX9244/MAX9246/ MAX9254 have a falling-edge strobe. 24 RxOUT0 26 RxOUT1 27 RxOUT2 28, 36, 48 VCCO 29 RxOUT3 30 RxOUT4 31 RxOUT5 33 RxOUT6 Channel 0 Single-Ended Outputs Output Supply Voltage. Bypass each VCCO to GND with 0.1F and 0.001F capacitors in parallel as close to the pin as possible. Channel 0 Single-Ended Outputs ______________________________________________________________________________________ 11 MAX9242/MAX9244/MAX9246/MAX9254 Pin Description 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance MAX9242/MAX9244/MAX9246/MAX9254 Pin Description (continued) PIN NAME FUNCTION 34 RxOUT7 35 RxOUT8 37 RxOUT9 39 RxOUT10 40 RxOUT11 41 RxOUT12 42 VCC Channel 1 Single-Ended Outputs Digital Supply Voltage. Bypass VCC to GND with 0.1F and 0.001F capacitors in parallel as close to the pin as possible. 43 RxOUT13 45 RxOUT14 46 RxOUT15 47 RxOUT16 Channel 1 Single-Ended Output Channel 2 Single-Ended Outputs Functional Diagram CHANNEL 0 RxIN0+ SERIAL-TO-PARALLEL 7 7 7 7 RxOUT0-RxOUT6 RxIN0CHANNEL 1 RxIN1+ SERIAL-TO-PARALLEL RxIN1- RxOUT7-RxOUT13 FIFO CHANNEL 2 RxIN2+ SERIAL-TO-PARALLEL 7 7 RxOUT14-RxOUT20 RxIN27x OR 9x STROBES RxCLKIN+ PARALLEL CLOCK CLK IN CLK OUT PLL1 RxCLKINFIFO CONTROL DCB 12 MAX9242 MAX9244 MAX9246 MAX9254 SPREADSPECTRUM PLL (SSPLL) PWRDWN SSG RxCLKOUT ______________________________________________________________________________________ 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance The MAX9242/MAX9244/MAX9246/MAX9254 deserialize three LVDS serial-data inputs into 21 single-ended LVCMOS/LVTTL outputs. The outputs are programmable for no spread or for a spread of 2% or 4%, relative to the LVDS input clock frequency. The MAX9242/MAX9244/ MAX9254 operate at a parallel clock frequency of 16MHz to 34MHz in DC-balanced mode and 20MHz to 40MHz in non-DC-balanced mode. The MAX9246 operates at a 6MHz-to-18MHz parallel clock frequency in DC-balanced mode and 8MHz-to-20MHz parallel clock frequency in non-DC-balanced mode. DC-balanced or non-DC-balanced operation is controlled by the DCB input. The MAX9242 has a rising-edge strobe and the MAX9244/ MAX9246/MAX9254 have a falling-edge strobe. DC Balance (DCB) DC-balanced or non-DC-balanced operation is controlled by the DCB input (see Table 1). In the non-DCbalanced mode, each channel deserializes 7 bits every cycle of the parallel clock. In DC-balanced mode, 9 bits are deserialized every clock cycle (7 data bits + 2 DC-balanced bits). The highest serial-data rate on each channel in DC-balanced mode is 34MHz x 9 = 306Mbps. In non-DC-balanced mode, the maximum data rate is 40MHz x 7 = 280Mbps. Table 1. DCB Function DCB INPUT LEVEL FUNCTION High Non-DC-balanced mode Mid Reserved Low DC-balanced mode Data coding by the MAX9209/MAX9213 serializers (that are companion devices to the MAX9242/MAX9244/ MAX9246/MAX9254 deserializers) limits the imbalance of ones and zeros transmitted on each channel. If +1 is assigned to each binary 1 transmitted and -1 is assigned to each binary 0 transmitted, the variation in the running sum of assigned values is called the digital sum variation (DSV). The maximum DSV for the data channels is 10. At most, 10 more zeros than ones, or 10 more ones than zeros, are ever transmitted. The maximum DSV for the clock channel is 5. Limiting the DSV and choosing the correct coupling capacitors maintain differential signal amplitude and reduces jitter due to droop on AC-coupled links. To obtain DC balance on the data channels, the serializer parallel data is inverted or not inverted, depending on the sign of the digital sum at the word boundary. Two complementary bits are appended to each group of 7 parallel-input data bits to indicate to the MAX9242/ MAX9244/MAX9246/MAX9254 deserializer whether the data bits are inverted (see Figures 11 and 12). The deserializer restores the original state of the parallel data. The LVDS clock signal alternates duty cycles of 4/9 and 5/9 to maintain DC balance. Spread-Spectrum Generator (SSG) The MAX9242/MAX9244/MAX9246/MAX9254 singleended data and clock outputs are programmable for a variation of 2% or 4% around the LVDS input clock frequency. The modulation rate of the frequency variation is 32.48kHz for a 33MHz LVDS clock input and scales linearly with the input clock frequency (see Table 2). The spread spectrum can also be turned off. The output spread is controlled through the SSG input (see Table 3). + RxCLKIN_ CYCLE N - 1 TxIN15 CYCLE N CYCLE N + 1 TxIN14 TxIN20 TxIN19 TxIN18 TxIN17 TxIN16 TxIN15 TxIN14 TxIN20 TxIN19 TxIN18 TxIN17 TxIN16 TxIN15 TxIN14 TxIN7 TxIN13 TxIN12 TxIN11 TxIN10 TxIN9 TxIN8 TxIN7 TxIN13 TxIN12 TxIN11 TxIN10 TxIN9 TxIN8 TxIN7 TxIN0 TxIN6 TxIN5 TxIN4 TxIN3 TxIN2 TxIN1 TxIN0 TxIN6 TxIN5 TxIN4 TxIN3 TxIN2 TxIN1 TxIN0 RxIN2_ TxIN8 RxIN1_ TxIN1 RxIN0_ TxIN_ IS DATA FROM THE SERIALIZER. Figure 11. Deserializer Serial Input in Non-DC-Balanced Mode ______________________________________________________________________________________ 13 MAX9242/MAX9244/MAX9246/MAX9254 Detailed Description MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance + RxCLKIN_ CYCLE N - 1 DCA2 CYCLE N CYCLE N + 1 DCB2 TxIN20 TxIN19 TxIN18 TxIN17 TxIN16 TxIN15 TxIN14 DCA2 DCB2 TxIN20 TxIN19 TxIN18 TxIN17 TxIN16 TxIN15 TxIN14 DCB1 TxIN13 TxIN12 TxIN11 TxIN10 TxIN9 TxIN8 TxIN7 DCA1 DCB1 TxIN13 TxIN12 TxIN11 TxIN10 TxIN9 TxIN8 TxIN7 DCB0 TxIN6 TxIN5 TxIN4 TxIN3 TxIN2 TxIN1 TxIN0 DCA0 DCB0 TxIN6 TxIN5 TxIN4 TxIN3 TxIN2 TxIN1 TxIN0 RxIN2_ DCA1 RxIN1_ DCA0 RxIN0_ TxIN_, DCA_, AND DCB_ ARE DATA FROM THE SERIALIZER. Figure 12. Deserializer Serial Input in DC-Balanced Mode Table 2. Modulation Rate fRxCLKIN_ (MHz) fM (kHz) = fRxCLKIN_ / 1016 6 5.91 8 7.87 10 9.84 16 15.75 18 17.72 20 19.68 33 32.48 34 33.46 Hot Swap 40 39.37 When the MAX9242/MAX9244/MAX9246/MAX9254 are connected to an active serializer, they synchronize correctly. The PLL control voltage does not saturate in response to high-frequency glitches that may occur during a hot swap. The PWRDWN input on the MAX9242/MAX9244/MAX9246/ MAX9254 does not need to be cycled when these devices are connected to an active serializer. Table 3. SSG Function SSG INPUT LEVEL FUNCTION High RxCLKOUT frequency spread 4% relative to RxCLKIN_ Mid RxCLKOUT frequency spread 2% relative to RxCLKIN_ Low No spread on RxCLKOUT relative to RxCLKIN_ Note: RxOUT_ data outputs are spread because RxCLKOUT strobes the output of the FIFO. 14 To select the mid level, leave the input open, or if driven, put the driver output in high impedance. The driver highimpedance leakage current must be less than 10A. Any spread change causes a maximum delay time of 32,800 x RCIP before output data is valid. When the spread amount is changed from 2% to 4% or viceversa, the data outputs go low for one delay time (see Figure 13). Similarly, when the spread is changed from no spread to 2% or 4%, the data outputs go low for one delay time (see Figure 14). The data outputs continue to switch but are not valid when the spread amount is changed from 2% or 4% to no spread (see Figure 15). The spread-spectrum function is also available when the MAX9242/MAX9244/MAX9246/MAX9254 operate in non-DC-balanced mode. PLL Lock Time The MAX9242/MAX9244/MAX9246/MAX9254 use two PLLs. The first PLL (PLL1) generates a 7x clock (non-DCbalanced mode) or a 9x clock (DC-balanced mode) from RxCLKIN_ for deserializing the LVDS inputs. The second PLL (SSPLL) is used for spread-spectrum modulation. During initial power-up, the PLL1 locks, and SSPLL locks immediately after. The PLL lock times are set by an internal counter. The maximum time to lock for each PLL is 32,800 clock periods. Power and clock should be stable to meet the lock time specification. After initialization, if the first PLL loses lock, it locks again and then the ______________________________________________________________________________________ 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance 4% OR 2% SPREAD MAX9242/MAX9244/MAX9246/MAX9254 SSG 2% OR 4% SPREAD RPLLS2 (32,800 x RCIP) RxCLKOUT RxOUT_ LOW Figure 13. Output Waveforms when Spread Amount is Changed SSG NO SPREAD 2% OR 4% SPREAD RPLLS2 (32,800 x RCIP) RxCLKOUT RxOUT_ LOW Figure 14. Output Waveforms when Spread is Added SSG 4% OR 2% SPREAD NO SPREAD RPLLS2 (32,800 x RCIP) RxCLKOUT RxOUT_ DATA SWITCHING BUT NOT VALID Figure 15. Output Waveforms when Spread is Removed spread-spectrum PLL locks immediately after (see Figure 16). If the spread-spectrum PLL loses lock, it locks again with only one PLL lock delay (see Figure 17). AC-Coupling Benefits Bit errors experienced with DC-coupling (Figure 18) can be eliminated by increasing the receiver commonmode voltage range through AC-coupling. AC-coupling increases the common-mode voltage range of an LVDS receiver to nearly the voltage rating of the capacitor. The typical LVDS driver output is 350mV centered on a 1.25V offset voltage, making single-ended output voltages of 1.425V and 1.075V. An LVDS receiver accepts signals from 0V to 2.4V, allowing approximately 1V commonmode difference between the driver and receiver on a ______________________________________________________________________________________ 15 MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance RPLLS (65,600 x RCIP) INTERNAL PLL1 LOCK INTERNAL SSPLL LOCK RxCLKOUT LOW LOW RxOUT_ LOW LOW Figure 16. Output Waveforms when PLL1 Loses Lock and Locks Again RPLLS2 (32,800 x RCIP) INTERNAL SSPLL LOCK RxCLKOUT RxOUT_ LOW TIMING SHOWN FOR STABLE CLOCK AND DATA INPUTS Figure 17. Output Waveforms if Spread-Spectrum PLL Loses Lock and Locks Again DC-coupled link (2.4V - 1.425V = 0.975V and 1.075V 0V = 1.075V). Common-mode voltage differences may be due to ground potential variation or common-mode noise. If there is more than 1V of difference, the receiver is not guaranteed to read the input signal correctly and may cause bit errors. AC-coupling filters low-frequency ground shifts and common-mode noise and passes high-frequency data. A common-mode voltage difference up to the voltage rating of the coupling capacitor (minus half the differential swing) is tolerated. DC-balanced coding of the data is required to maintain the differential signal amplitude and limit jitter on an AC-coupled link. A capacitor in series with each output of the LVDS driver is sufficient for AC-coupling. However, two capacitors--one at the serializer output and one at the deserializer input--provide protection in case either end of the cable is shorted to a high voltage. 16 Applications Information Selection of AC-Coupling Capacitors Voltage droop and the DSV of transmitted symbols cause signal transitions to start from different voltage levels. Because the transition time is finite, starting the signal transition from different voltage levels causes timing jitter. The time constant for an AC-coupled link needs to be chosen to reduce droop and jitter to an acceptable level. The RC network for an AC-coupled link consists of the LVDS receiver termination resistor (RT), the LVDS driver output resistor (RO), and the series AC-coupling capacitors (C). The RC time constant for two equal-value series capacitors is (C x (RT + RO)) / 2 (Figure 19). The RC time constant for four equal-value series capacitors is (C x (RT + RO)) / 4 (Figure 20). ______________________________________________________________________________________ 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance TRANSMISSION LINE TxOUT RO 7 MAX9242/MAX9244/MAX9246/MAX9254 RxIN__ RT 7 7:1 100 1:7 FIFO 7:1 100 1:7 FIFO 7:1 100 1:7 FIFO PLL 100 PLL1 + SSPLL 7 7 TxIN RxOUT_ 7 7 PWRDWN TxCLK IN TxCLK OUT 21:3 SERIALIZER PWRDWN RxCLK OUT RxCLK IN 3:21 DESERIALIZER Figure 18. DC-Coupled Link, Non-DC-Balanced Mode RT is required to match the transmission line impedance (usually 100) and RO is determined by the LVDS driver design (the minimum differential output resistance of 78 for the MAX9209/MAX9213 serializers is used in the following example). This condition leaves the capacitor selection to change the system time constant. In the following example, the capacitor value for a 2% droop is calculated. Jitter due to this droop is then calculated assuming a 1ns transition time: C = -(2 x tB x DSV) / (ln (1 - D) x (RT + RO)) (Eq 1) where: C = AC-coupling capacitor (F) tB = bit time (s) DSV = digital sum variation (integer) ln = natural log D = droop (% of signal amplitude) RT = termination resistor () RO = output resistance () Equation 1 is for two series capacitors (Figure 19). The bit time (tB) is the period of the parallel clock divided by 9. The DSV is 10. See equation 3 for four series capacitors (Figure 20). The capacitor for 2% maximum droop at 16MHz parallel rate clock is: C = -(2 x tB x DSV) / (ln (1 - D) x (RT + RO)) C = -(2 x 6.95ns x 10) / (ln (1 - 0.02) x (100 + 78)) C = 0.038F Jitter due to droop is proportional to the droop and transition time: tJ = tT x D (Eq 2) where: tJ = jitter (s) tT = transition time (s) (0 to 100%) D = droop (% of signal amplitude) Jitter due to 2% droop and assumed 1ns transition time is: tJ = 1ns x 0.02 tJ = 20ps The transition time in a real system depends on the frequency response of the cable driven by the serializer. ______________________________________________________________________________________ 17 MAX9242/MAX9244/MAX9246/MAX9254 MAX9209/MAX9213 MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance HIGH-FREQUENCY, CERAMIC SURFACE-MOUNT CAPACITORS CAN ALSO BE PLACED AT THE SERIALIZER INSTEAD OF THE DESERIALIZER. MAX9209/MAX9213 TxOUT RxIN__ (7 + 2):1 RT 100 (7 + 2):1 100 1:(9 - 2) + FIFO (7 + 2):1 100 1:(9 - 2) + FIFO PLL 100 PLL1 + SSPLL RO 7 7 TxIN MAX9242/MAX9244/MAX9246/MAX9254 7 PWRDWN TxCLK IN TxCLK OUT 1:(9 - 2) + FIFO 7 7 RxOUT_ 7 PWRDWN RxCLK OUT RxCLK IN 21:3 SERIALIZER 3:21 DESERIALIZER Figure 19. Two Capacitors per Link, AC-Coupled, DC-Balanced Mode The capacitor value decreases for a higher frequency parallel clock and for higher levels of droop and jitter. Use high-frequency, surface-mount ceramic capacitors. Equation 1 altered for four series capacitors (Figure 20) is: C = -(4 x tB x DSV) / (ln (1 - D) x (RT + RO)) (Eq 3) Fail-Safe The MAX9242/MAX9244/MAX9246/MAX9254 have failsafe LVDS inputs in non-DC-balanced mode (Figure 1). Fail-safe drives the outputs low when the corresponding LVDS input is open, undriven and shorted, or undriven and parallel terminated. The fail-safe on the LVDS clock input drives all outputs low when power is stable. Failsafe does not operate in DC-balanced mode. Input Bias and Frequency Detection In DC-balanced mode, the inverting and noninverting LVDS inputs are internally connected to +1.2V through 42k (min) to provide biasing for AC-coupling (Figure 1). To prevent switching due to noise when the clock input is not driven, bias the clock inputs (RxCLKIN+, 18 RxCLKIN-) to differential +15mV by connecting a 10k 1% pullup resistor between the noninverting input and LVDSVCC, and a 10k 1% pulldown resistor between the inverting input and ground. These bias resistors, along with the 100 1% tolerant termination resistor, provide +15mV of differential input. The +15mV bias causes some small degradation of RSKM proportional to the slew rate of the clock input. For example, if the clock transitions 250mV in 500ps, the slew rate of 0.5mV/ps reduces RSKM by 30ps. Unused LVDS Data Inputs In non-DC-balanced mode, leave unused LVDS data inputs open. In non-DC-balanced mode, the input failsafe circuit drives the corresponding outputs low, and no pullup or pulldown resistors are needed. In DC-balanced mode, at each unused LVDS data input, pull the inverting input up to LVDSVCC using a 10k resistor, and pull the noninverting input down to ground using a 10k resistor. Do not connect a termination resistor. The pullup and pulldown resistors drive the corresponding outputs low and prevent switching due to noise. ______________________________________________________________________________________ 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance MAX9209/MAX9213 MAX9242/MAX9244/MAX9246/MAX9254 TxOUT RxIN__ (7 + 2):1 RT 100 (7 + 2):1 100 1:(9 - 2) + FIFO (7 + 2):1 100 1:(9 - 2) + FIFO PLL 100 PLL1 + SSPLL RO 7 7 TxIN 1:(9 - 2) + FIFO 7 7 RxOUT_ 7 7 PWRDWN TxCLK IN TxCLK OUT PWRDWN RxCLK OUT RxCLK IN 21:3 SERIALIZER 3:21 DESERIALIZER Figure 20. Four Capacitors per Link, AC-Coupled, DC-Balanced Mode Link Power-Up Sequence The recommended link power-up sequence is to power up the serializer, wait until the serializer PLL locks, and then power up the deserializer. This sequence prevents the deserializer from seeing an undriven or unstable input when powering up. PWRDWN Driving PWRDWN low puts the outputs in high impedance, stops the PLL, and reduces supply current to 50A or less. Driving PWRDWN high drives the outputs low until the PLL locks. The outputs of two deserializers can be bused to form a 2:1 mux with the outputs controlled by PWRDWN. Wait 100ns between disabling one deserializer (driving PWRDWN low) and enabling the second one (driving PWRDWN high) to avoid contention of the bused outputs. Power-Supply Bypassing There are separate on-chip power domains for digital circuits, outputs, PLL, and LVDS inputs. Bypass each VCC, VCCO, PLLVCC, and LVDSVCC with high-frequency, surface-mount ceramic 0.1F and 0.001F capacitors in parallel as close to the device as possible, with the smallest value capacitor closest to the supply pin. Cables and Connectors Interconnect for LVDS typically has a differential impedance of 100. Use cables and connectors that have matched differential impedance to minimize impedance discontinuities. Twisted-pair and shielded twisted-pair cables offer superior signal quality compared to ribbon cable and tend to generate less EMI due to magnetic field canceling effects. Balanced cables pick up noise as common mode, which is rejected by the LVDS receiver. Board Layout Keep the LVTTL/LVCMOS outputs and LVDS input signals separated to prevent crosstalk. A four-layer PC board with separate layers for power, ground, LVDS inputs, and digital signals is recommended. Layout PC board traces for 100 differential characteristic impedance. The trace dimensions depend on the type of ______________________________________________________________________________________ 19 MAX9242/MAX9244/MAX9246/MAX9254 HIGH-FREQUENCY CERAMIC SURFACE-MOUNT CAPACITORS MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance trace used (microstrip or stripline). Note that two 50 PC board traces do not have 100 differential impedance when brought close together--the impedance goes down when the traces are brought closer. Route the PC board traces for an LVDS channel (there are two conductors per LVDS channel) in parallel to maintain the differential characteristic impedance. Place the termination resistor at the end of the PC board traces within a 1/4 inch of the LVDS receiver input. Avoid vias. If vias must be used, use only one pair per LVDS channel and place the via for each line at the same point along the length of the PC board traces. This way, any reflections will occur at the same time. Do not make vias into test points for ATE. Make LVDS clock and data pairs the same length on the PC board to avoid pair-to-pair skew. Make the PC board traces that make up a differential pair the same length to avoid skew within the differential pair. 5V-Tolerant Input PWRDWN is 5V tolerant and is internally pulled down to GND. SSG and DCB are not 5V tolerant. The input voltage range for SSG and DCB is nominally ground to VCC. Skew Margin (RSKM) Skew margin (RSKM) is the time allowed for degradation of the serial-data sampling setup and hold times by sources other than the deserializer. The deserializer sampling uncertainty is accounted for and does not need to be subtracted from RSKM. The main outside contributors of jitter and skew that subtract from RSKM are interconnect intersymbol interference, serializer pulse position uncertainty, and pair-to-pair path skew. VCCO Output Supply and Power Dissipation The outputs have a separate supply (VCCO) for interfacing to systems with 1.8V to 5V nominal input logic levels. The DC Electrical Characteristics table gives the maximum supply current for VCCO = 3.6V with 8pF load at several switching frequencies with all outputs switching in the worst-case switching pattern. The approximate incremental supply current for VCCO other than 3.6V with the same 8pF load and worst-case pattern can be calculated using: II = CTVI0.5fC x 21 (data outputs) + CTVIfC x 1 (clock output) where: II = incremental supply current CT = total internal (CINT) and external (CL) load capacitance VI = incremental supply voltage fC = output clock switching frequency 20 The incremental current is added to (for VCCO > 3.6V) or subtracted from (for VCCO < 3.6V) the DC Electrical Characteristics table maximum supply current. The internal output buffer capacitance is CINT = 6pF. The worst-case pattern switching frequency of the data outputs is half the switching frequency of the output clock. In the following example, the incremental supply current of the MAX9244 in spread and DC-balanced mode is calculated for VCCO = 5.5V, fC = 34MHz, and CL = 8pF: VI = 5.5V - 3.6V = 1.9V CT = CINT + CL = 6pF + 8pF = 14pF where: II = CTVI0.5fC x 21 (data outputs) + CTVIfC x 1 (clock output) II = (14pF x 1.9V x 0.5 x 34MHz x 21) + (14pF x 1.9V x 34MHz) II = 9.5mA + 0.9mA = 10.4mA. The maximum supply current in DC-balanced mode for VCC = VCCO = 3.6V at fC = 34MHz is 125mA (from the DC Electrical Characteristics table). Add 10.4mA to get the total approximate maximum supply current at VCCO = 5.5V and VCC = 3.6V. If the output supply voltage is less than VCCO = 3.6V, the reduced supply current can be calculated using the same formula and method. At high switching frequency, high supply voltage, and high capacitive loading, power dissipation can exceed the package power dissipation rating. Do not exceed the maximum package power dissipation rating. See the Absolute Maximum Ratings for maximum package power dissipation capacity and temperature derating. Rising- or Falling-Edge Output Strobe The MAX9242 has a rising-edge output strobe, which latches the parallel output data into the next chip on the rising edge of RxCLKOUT. The MAX9244/MAX9246/ MAX9254 have a falling-edge output strobe, which latches the parallel output data into the next chip on the falling edge of RxCLKOUT. The deserializer output strobe polarity does not need to match the serializer input strobe polarity. Three-Level Logic Inputs SSG and DCB (DCB mid level is reserved) are threelevel-logic inputs. A logic-high input voltage must be greater than +2.5V and a logic-low input voltage must be less than +0.8V. A mid-level logic is recognized by the MAX9242/MAX9244/MAX9246/MAX9254 when the input is left open or connected to a driver in a highimpedance state. A weak inverter on the input stage of ______________________________________________________________________________________ 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance IEC 61000-4-2 Level 4 and ISO 10605 ESD Protection The MAX9242/MAX9244/MAX9246/MAX9254 ESD tolerance is rated for Human Body Model, IEC 61000-4-2 and ISO 10605. The ISO 10605 and IEC 61000-4-2 standards specify ESD tolerance for electronic systems. All LVDS inputs on the MAX9242/MAX9244/ MAX9246/MAX9254 meet ISO 10605 ESD protection at 30kV Air-Gap Discharge and 6kV Contact Discharge and IEC 61000-4-2 ESD protection at 15kV Air-Gap Discharge and 8kV Contact Discharge. All other pins meet the Human Body Model ESD tolerance of 2.5kV. The Human Body Model discharge components are CS = 100pF and RD = 1.5k (Figure 21). The IEC 61000-42 discharge components are CS = 150pF and RD = 330 (see Figure 22). The ISO 10605 discharge components are CS = 330pF and RD = 2k (Figure 23). RD 1.5k CHARGE-CURRENTLIMIT RESISTOR HIGHVOLTAGE DC SOURCE CS 100pF DISCHARGE RESISTANCE STORAGE CAPACITOR DEVICE UNDER TEST Figure 21. Human Body ESD Test Circuit R2 330 CHARGE-CURRENTLIMIT RESISTOR HIGHVOLTAGE DC SOURCE CS 150pF DISCHARGE RESISTANCE STORAGE CAPACITOR DEVICE UNDER TEST RD 2k CHARGE-CURRENTLIMIT RESISTOR HIGHVOLTAGE DC SOURCE CS 330pF DISCHARGE RESISTANCE DEVICE UNDER TEST STORAGE CAPACITOR Figure 23. ISO 10605 Contact Discharge ESD Test Circuit Pin Configuration TOP VIEW RxOUT17 1 48 VCCO RxOUT18 2 47 RxOUT16 GND 3 46 RxOUT15 RxOUT19 4 45 RxOUT14 RxOUT20 5 44 GND SSG 6 43 RxOUT13 DCB 7 42 VCC RxIN0- 8 41 RxOUT12 RxIN0+ 9 40 RxOUT11 RxIN1- 10 39 RxOUT10 RxIN1+ 11 38 GND 37 RxOUT9 36 VCCO 35 RxOUT8 LVDSVCC 12 LVDSGND 13 RxIN2- 14 MAX9242 MAX9244 MAX9246 MAX9254 RxIN2+ 15 34 RxOUT7 RxCLKIN- 16 33 RxOUT6 RxCLKIN+ 17 32 GND LVDSGND 18 31 RxOUT5 PLLGND 19 30 RxOUT4 PLLVCC 20 29 RxOUT3 PLLGND 21 28 VCCO RxOUT2 PWRDWN 22 27 RxCLKOUT 23 26 RxOUT1 RxOUT0 24 25 GND TSSOP Figure 22. IEC 61000-4-2 Contact Discharge ESD Test Circuit Chip Information PROCESS: CMOS ______________________________________________________________________________________ 21 MAX9242/MAX9244/MAX9246/MAX9254 SSG and DCB provides the proper mid-level voltage under conditions of low input current. The mid-level input current must not be greater than 10A, and the mid-level logic state cannot be driven with an external voltage source. MAX9242/MAX9244/MAX9246/MAX9254 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance Ordering Information (continued) PART MAX9246EUM MAX9246EUM/V+ TEMP RANGE PIN-PACKAGE -40C to +85C 48 TSSOP -40C to +85C 48 TSSOP MAX9246GUM -40C to +105C 48 TSSOP MAX9246GUM/V+ -40C to +105C 48 TSSOP MAX9254EUM -40C to +85C 48 TSSOP MAX9254EUM/V+ -40C to +85C 48 TSSOP Package Information For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. 48 TSSOP U48-1 21-0155 +Denotes a lead(Pb)-free/RoHS-compliant package. /V denotes an automotive qualified part. Note: All devices are available in lead(Pb)-free/RoHS-compliant packaging. Specify lead(Pb)-free/RoHS compliant by adding a + symbol at the end of the part number when ordering. 22 ______________________________________________________________________________________ 21-Bit Deserializers with Programmable Spread Spectrum and DC Balance REVISION NUMBER REVISION DATE 3 2/09 Supply currents measured before the deserializers were fully locked to incoming serial data. DC Electrical Characteristics updated 4 7/09 Added automotive qualified parts to Ordering Information table DESCRIPTION PAGES CHANGED 2, 3 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 23 (c) 2009 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc. MAX9242/MAX9244/MAX9246/MAX9254 Revision History Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX9242EUM/V+ MAX9242EUM/V+T MAX9242GUM/V+ MAX9242GUM/V+T MAX9244EUM/V+ MAX9244EUM/V+T MAX9244GUM/V+ MAX9244GUM/V+T MAX9246EUM/V+ MAX9246EUM/V+T MAX9246GUM/V+ MAX9246GUM/V+T MAX9254EUM/V+ MAX9254EUM/V+T MAX9242EUM+T MAX9242EUM+ MAX9242GUM+D MAX9242GUM+TD MAX9244EUM+D MAX9244EUM+TD MAX9244GUM+D MAX9244GUM+TD MAX9246EUM+D MAX9246EUM+TD MAX9246GUM+D MAX9246GUM+TD MAX9254EUM+ MAX9254EUM+D MAX9254EUM+T MAX9254EUM+TD