TLN117(F) TOSHIBA Infrared LED GaAs Infrared Emitter TLN117(F) Opto-Electronic Switches Floppy Disk Drives Optical Mice Optical Touch Sensors Unit: mm * Small side-view epoxy-resin package * High radiant intensity: IE = 0.8 mW / sr(min)at IF = 20 mA * Half-angle value: 1 / 2 = 15(typ.) Absolute Maximum Ratings (Ta = 25C) Characteristic Symbol Rating Unit Forward current IF 50 mA Pulse forward current IFP Forward current derating (Ta > 25C) 600 (Note 1) mA IF / C -0.33 mA / C Reverse voltage VR 5 V Operating temperature Topr -25 to 85 C Storage temperature Tstg -40 to 100 C Soldering temperature (5s) Tsol 260 (Note 2) C TOSHIBA 4-3P1 Weight: 0.1 g (typ.) Pin Connection Note: Using continuously under heavy loads (e.g. the application of high 1. Cathode 1 2 temperature/current/voltage and the significant change in 2. Anode temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Pulse width < 100 s, repetitive frequency =100 Hz Note 2: Solder the LED no closer than 2mm from the base of the lead. 1 2008-07-11 TLN117(F) Optical and Electrical Characteristics (Ta = 25C) Characteristic Symbol Test Condition Min Typ. Max Unit Forward voltage VF IF = 10 mA 1.0 1.15 1.3 V Reverse current IR VR = 5 V 10 A TLN117(F) 2 Radiant intensity IE IF = 20 mA TLN117(B,F) 2 7.5 TLN117(C,F) 5 18.7 mW / sr Radiant power PO IF = 20 mA 2.5 mW Capacitance CT VR = 0, f = 1 MHz 30 pF Peak emission wavelength P IF = 20 mA 940 nm Spectral line half width IF = 20 mA 50 nm 1/2 IF = 20 mA 15 Half value angle Precautions Please be careful of the followings. 1. When forming the leads, bend each lead under the 2mm from the body of the device. Soldering must be performed after the leads have been formed. 2. Radiation intensity falls over time due to the current which flows in the infrared LED. When designing a circuit, take into account this change in radiant power over time. The ratio of fluctuation in radiation intensity to fluctuation in optical output is 1: 1. I E (t) PO (t) = I E (0) PO (0) 2 2008-07-11 Allowable pulse forward current IFP (mA) TLN117(F) IF - Ta Allowable forward current IF (mA) 80 60 40 20 0 20 60 40 80 IFP - PW 3000 Ta = 25C 1000 f = 100 Hz 500 200 Hz 300 500 Hz 100 50 30 10 kHz 10 3 10 5 kHz 2 kHz 100 300 30 Pulse width 100 1 kHz PW 1m 3m 10 m (s) Ambient temperature Ta (C) IF - V F (typ.) IE - IFP 50 (typ.) 30 30 10 Radiant intensity IE (mW / sr) (mA) Forward current IF Pulse 10 Ta = 75C 50 5 25 -25 0 3 5 3 1 DC 0.5 Pulse width < 100 s Repetitive Frequency = 100 Hz Ta = 25C 0.3 1 0.9 1.0 1.1 1.2 1.3 Forward voltage VF 1.4 1.5 0.1 1 (V) 3 10 30 100 300 Pulse forward current IFP (mA) 3 2008-07-11 TLN117(F) IFP - VFP (typ.) Relative IE - Ta 5 500 3 Relative radiant intensity 1000 Pulse forward current IFP (mA) 300 100 50 30 1 0.5 0.3 10 0.1 -40 -20 5 1 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 20 60 40 80 100 Ambient temperature Ta (C) Pulse width < 100 s Repetitive Frequency = 100 Hz Ta = 25C 3 (typ.) 2.2 2.4 Pulse forward voltage VFP (V) Wavelength Characteristic 1.0 (typ.) Radiation Pattern IF = 20 mA Ta = 25C 20 0 (Ta = 25C) 10 20 30 30 0.8 Relative intensity 10 (typ.) 40 40 50 50 0.6 60 60 70 70 0.4 80 80 90 0.2 0 0.2 0.4 0.6 0.8 90 1.0 Relative intensity 0 820 860 900 940 980 1020 Wavelength (nm) 4 2008-07-11 TLN117(F) RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact ("Unintended Use"). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 5 2008-07-11