19-1334; Rev 0; 1/98 Regulated, 125mA-Output, Charge-Pump DC-DC Inverter ____________________________Features The MAX1673 charge-pump inverter provides a lowcost, compact means of generating a regulated negative output from a positive input at up to 125mA. It requires only three small capacitors, and only two resistors to set its output voltage. The input range is 2V to 5.5V. The regulated output can be set from 0V to -VIN in Skip regulation mode or -1.5V to -VIN in Linear (LIN) regulation mode. In Skip mode, the MAX1673 regulates by varying its switching frequency as a function of load current. This On-DemandTM switching gives the MAX1673 two advantages: very small capacitors and very low quiescent supply current. At heavy loads, it transfers energy from the input to the output by switching at up to 350kHz. It switches more slowly at light loads, using only 35A quiescent supply current. Regulated Negative Output Voltage (up to -1 x VIN) In Linear mode, the MAX1673 switches at a constant 350kHz at all loads and regulates by controlling the current-path resistance. This provides constantfrequency ripple, which is easily filtered for low-noise applications. This device also features a 1A logic-controlled shutdown mode and is available in a standard 8-pin SO package. For a device that delivers about 10mA and fits in a smaller package, refer to the MAX868. 125mA Output Current 35A Quiescent Supply Current (Skip-mode regulation) 350kHz Fixed-Frequency, Low-Noise Output (Linear-mode regulation) 2V to 5.5V Input Range 1A Logic-Controlled Shutdown _______________Ordering Information PART MAX1673ESA TEMP. RANGE PIN-PACKAGE -40C to +85C 8 SO ________________________Applications Hard Disk Drives Measurement Instruments Camcorders Modems Analog Signal-Processing Applications Digital Cameras Typical Operating Circuit INPUT 2V TO 5.5V ___________________Pin Configuration ON TOP VIEW OFF LIN/SKIP 1 8 SHDN IN CAP+ CAP+ 2 7 GND CAP- 3 6 FB SHDN 4 5 OUT MAX1673 IN FB MAX1673 REGULATED NEGATIVE OUTPUT (UP TO -1 x VIN, UP TO 125mA) OUT CAPLIN/SKIP GND SO On-DemandTM is a trademark of Maxim Integrated Products. ________________________________________________________________ Maxim Integrated Products 1 For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468. MAX1673 ________________General Description MAX1673 Regulated, 125mA-Output, Charge-Pump DC-DC Inverter ABSOLUTE MAXIMUM RATINGS IN ..............................................................................-0.3V to +6V CAP+, FB, LIN/SKIP.....................................-0.3V to (VIN + 0.3V) SHDN........................................................................-0.3V to +6V OUT, CAP-................................................................-6V to +0.3V Continuous Output Current ...............................................135mA Output Short-Circuit Duration to GND (Note 1) ....................1sec Continuous Power Dissipation (TA = +70C) (derate 5.88mW/C above +70C) ...............................450mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +160C Lead Temperature (soldering, 10sec) .............................+300C Note 1: Shorting OUT to IN may damage the device and should be avoided. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VIN = V SHDN = +5V, CIN = 10F, COUT = 22F, CFLY = 2.2F, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = +25C.) (Note 2) PARAMETER Input Voltage Range SYMBOL VIN Minimum Output Voltage VOUT Maximum Output Current IOUT(MAX) Output Voltage VOUT CONDITIONS MIN LIN/SKIP = GND (Skip mode) 2.0 5.5 LIN/SKIP = IN (LIN mode) 2.7 5.5 Shutdown Current (IIN Current) Line Regulation Load Regulation Open-Loop Output Resistance (Dropout) Output Resistance to Ground in Shutdown Mode 2 IQ 125 LIN/SKIP = IN R1 =100k, 1%, (LIN mode) R2 = 60.4k, 1%, IOUT = 0mA to 125mA, Figure 1 LIN/SKIP = GND (Skip mode) V mA -3.02 -3.15 V -2.92 -3.02 -3.12 8 16 0.035 0.2 0.1 1 mA VFB = -25mV, VOUT = -3V, LIN/SKIP = GND (Skip mode) SHDN = GND VLNR VIN = 4.5V to 5.5V, Figure 4, VREF VIN RO -2.90 UNITS V -1.5 LIN/SKIP = IN ISHDN VLDR MAX 0 LIN/SKIP = GND VFB = -100mV, VOUT = -3V, LIN/SKIP = IN (LIN mode) Quiescent Current (IIN Current) TYP IOUT = 25mA to 125mA, Figure 1 LIN/SKIP = IN (LIN mode) 0.01 %/V LIN/SKIP = GND (Skip mode) 1 LIN/SKIP = IN (LIN mode) 0.01 LIN/SKIP = GND (Skip mode) 0.005 %/mA LIN/SKIP = GND (Skip mode) SHDN = GND A 3.5 10 1 5 _______________________________________________________________________________________ Regulated, 125mA-Output, Charge-Pump DC-DC Inverter (VIN = V SHDN = +5V, CIN = 10F, COUT = 22F, CFLY = 2.2F, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = +25C.) (Note 2) PARAMETER Switching Frequency (LIN Mode) FB Threshold FB Input Bias Current SYMBOL MIN TYP MAX OSC TA = +25C 250 350 460 TA = -40C to +85C 205 VFBT LIN/SKIP = GND (Skip mode) -25 IFB CONDITIONS LIN/SKIP = IN (LIN mode) LIN/SKIP = GND (Skip mode) 515 0 25 150 600 1 100 VFB = -25mV 1 VIH 2V VIN 5.5V Logic Low Input (SHDN, LIN/SKIP) VIL 2V VIN 5.5V kHz mV nA VFB = -25mV Input Bias Current (SHDN, LIN/SKIP) Logic High Input (SHDN, LIN/SKIP) UNITS 0.7 x VIN A V 0.3 x VIN V Note 2: Specifications to -40C are guaranteed by design, not production tested. _______________________________________________________________________________________ 3 MAX1673 ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (Circuit of Figure 1, VIN = +5V, CFLY = 2.2F, COUT = 22F, TA = +25C, unless otherwise noted.) COUT = 47F 40 MAX1673 TOC02 -3.05 150 COUT = 22F 50 75 100 125 0 50 75 100 125 LOAD CURRENT (mA) EFFICIENCY vs. LOAD CURRENT (SKIP MODE) EFFICIENCY vs. LOAD CURRENT (LIN MODE) VIN = 4V 70 VIN = 5V 60 80 50 40 -2.98 150 30 0 VREF VIN CIRCUIT OF FIGURE 4 20 40 60 50 VIN = 5V 40 30 70 80 100 120 60 LIN MODE 50 VREF VIN 100mA LOAD VOUT = -3V CIRCUIT OF FIGURE 4 30 0 140 20 40 60 80 100 120 140 3.5 4.0 4.5 5.0 5.5 6.0 LOAD CURRENT (mA) LOAD CURRENT (mA) VIN (V) DROPOUT OUTPUT RESISTANCE vs. INPUT VOLTAGE QUIESCENT CURRENT vs. INPUT VOLTAGE (LIN MODE) QUIESCENT CURRENT vs. INPUT VOLTAGE (SKIP MODE) MAX1673 TOC07 12 10 8 TA = +25C TA = +85C 6 4 2 12 DOES NOT INCLUDE BIAS CURRENT FOR RESISTOR DIVIDER 10 8 6 4 0 VREF VIN CIRCUIT OF FIGURE 4 0 3 4 VIN (V) 5 6 45 DOES NOT INCLUDE BIAS CURRENT FOR RESISTOR DIVIDER 40 35 30 25 20 15 10 2 TA = -40C 2 150 SKIP MODE 40 VREF VIN CIRCUIT OF FIGURE 4 0 60 125 MAX1673 TOC09 0 100 80 QUIESCENT CURRENT (A) 0 75 EFFICIENCY vs. INPUT VOLTAGE VIN = 4.5V 10 QUIESCENT CURRENT (mA) 10 50 90 20 20 25 LOAD CURRENT (mA) VIN = 4V 70 EFFICIENCY (%) VIN = 3.5V 80 -2.99 90 MAX1673 TOC04 90 4 25 LOAD CURRENT (mA) 100 EFFICIENCY (%) 150 LIN MODE -3.00 C CFLY = OUT 10 0 25 -3.03 -3.01 COUT = 47F 20 0 -3.04 -3.02 100 50 0 SKIP MODE -3.06 MAX1673 TOC06 60 200 -3.07 VOUT (V) COUT = 22F 80 COUT = 10F EFFICIENCY (%) 100 -3.08 MAX1673 TOC05 COUT = 10F MAX1673 TOC08 PEAK-TO-PEAK RIPPLE (mV) 120 OUTPUT VOLTAGE vs. LOAD CURRENT 250 PEAK-TO-PEAK RIPPLE (mV) C CFLY = OUT 10 MAX1673 RTOC01 140 OUTPUT RIPPLE vs. LOAD CURRENT (SKIP MODE) MAX1673 TOC03 OUTPUT RIPPLE vs. LOAD CURRENT (LIN MODE) RDROPOUT () MAX1673 Regulated, 125mA-Output, Charge-Pump DC-DC Inverter 5 0 2 3 4 VIN (V) 5 6 2 3 4 VIN (V) _______________________________________________________________________________________ 5 6 Regulated, 125mA-Output, Charge-Pump DC-DC Inverter LOAD-TRANSIENT RESPONSE (SKIP MODE) LOAD-TRANSIENT RESPONSE (LIN MODE) MAX1673 TOC11 MAX1673 TOC10 125mA IOUT 100mA/div 125mA IOUT 100mA/div 25mA 25mA CIRCUIT OF FIGURE 4 VOUT 50mV/div VOUT 50mV/div CIRCUIT OF FIGURE 4 250s/div 250s/div LINE-TRANSIENT RESPONSE (SKIP MODE) LINE-TRANSIENT RESPONSE (LIN MODE) MAX1673 TOC13 MAX1673 TOC12 VIN 2V/div 5.5V VIN 2V/div IOUT = 100mA CIRCUIT OF FIGURE 4 VOUT 50mV/div 5.5V 4.5V 4.5V VOUT 50mV/div IOUT = 100mA CIRCUIT OF FIGURE 4 50s/div 50s/div _______________________________________________________________________________________ 5 MAX1673 Typical Operating Characteristics (continued) (Circuit of Figure 1, VIN = +5V, CFLY = 2.2F, COUT = 22F, TA = +25C, unless otherwise noted.) MAX1673 Regulated, 125mA-Output, Charge-Pump DC-DC Inverter ______________________________________________________________Pin Description PIN NAME FUNCTION 1 LIN/SKIP Regulation-Mode Select Input. Driving LIN/SKIP high or connecting it to IN selects LIN mode, with regulation accomplished by modulating switch resistance. Driving LIN/SKIP low or connecting it to GND selects Skip mode, where the device regulates by skipping charge-pump pulses. 2 CAP+ Positive Terminal of Flying Capacitor 3 CAP- Negative Terminal of Flying Capacitor 4 SHDN Shutdown Control Input. Drive SHDN low to shut down the MAX1673. Connect SHDN to IN for normal operation. OUT connects to GND through a 1 (typical) resistor in shutdown mode. 5 OUT 6 FB 7 GND 8 IN Inverting Charge-Pump Output Feedback Input. Connect FB to a resistor-divider from IN (or other reference source) to OUT for regulated output voltages (Figures 1 and 4). Ground Power-Supply Positive Voltage Input Detailed Description The MAX1673 new-generation, high-output-current, regulated charge-pump DC-DC inverter provides up to 125mA. Designed specifically for compact applications, a complete regulating circuit requires only three small capacitors and two resistors. The MAX1673 employs On-DemandTM regulation circuitry, providing output regulation modes optimized for either lowest output noise or lowest supply current. In addition, the MAX1673 includes shutdown control. In Linear (LIN) mode or when heavily loaded in Skip mode, the charge pump runs continuously at 350kHz. During one-half of the oscillator period, switches S1 and S2 close (Figure 2), charging the transfer capacitor (CFLY) to the input voltage (CAP- = GND, and CAP+ = IN). During the other half cycle, switches S3 and S4 close (Figure 3), transferring the charge on CFLY to the output capacitor (CAP+ = GND, CAP- = OUT). S1 CAP+ S3 IN S2 CFLY S4 COUT OUT CAP350kHz INPUT 5.0V CIN 10F ON OFF 4 2 CFLY 2.2F R1 100k 8 SHDN IN FB LIN SKIP 1 5 COUT 22F CAPLIN/SKIP 6 R1 60.4k CAP+ MAX1673 OUT 3 Figure 2. Charging CFLY S1 CAP+ S3 IN OUTPUT -3V S2 CFLY S4 COUT OUT CAP- GND 7 350kHz Figure 1. Standard Application Circuit 6 Figure 3. Transferring Charge on CFLY to COUT _______________________________________________________________________________________ Regulated, 125mA-Output, Charge-Pump DC-DC Inverter Skip Mode In Skip mode (LIN/SKIP = GND), the device switches only as needed to maintain regulation on FB. Switching cycles are skipped until the voltage on FB rises above GND. Skip mode has higher output noise than LIN mode, but minimizes operating current. INPUT 5.0V MAX1673 Linear Mode (Constant-Frequency Mode) In LIN mode (LIN/SKIP = IN), the charge pump runs continuously at 350kHz. The MAX1673 controls the charge on CFLY by varying the gate drive on S1 (Figure 2). When the output voltage falls, CFLY charges faster due to increased gate drive. Since the device switches continuously, the regulation scheme minimizes output ripple, the output noise contains well-defined frequency components, and the circuit requires much smaller external capacitors than in Skip mode for a given output ripple.* However, LIN mode is less efficient than Skip mode due to higher operating current (8mA typical). VREF 5V CIN 10F ON OFF 4 2 CFLY 2.2F 3 LIN SKIP R1 100k 8 1 SHDN IN FB VOUT = -VREF x R2 R1 R2 60.4k CAP+ MAX1673 OUT CAPLIN/SKIP 6 GND 5 COUT 22F OUTPUT -3V 7 Figure 4. Separate VREF for Voltage Divider Shutdown Mode Capacitor Selection When SHDN (a CMOS-compatible input) is driven low, the MAX1673 enters low-power shutdown mode. Charge-pump switching action halts and an internal 1 switch pulls VOUT to ground. Connect SHDN to IN or drive high for normal operation. A CFLY value of 1F or more is sufficient to supply the specified load current. However, for minimum ripple in Skip mode, this value may need to be increased. Maxim recommends 2.2F. Surface-mount ceramic capacitors are preferred for CFLY, due to their small size, low cost, and low equivalent series resistance (ESR). To ensure proper operation over the entire temperature range, choose ceramic capacitors with X7R (or equivalent) low-temperaturecoefficient (tempco) dielectrics. See Table 1 for a list of suggested capacitor suppliers. The output capacitor stores the charge transferred from the flying capacitor and services the load between oscillator cycles. A good general rule is to make the output capacitance at least ten times greater than that of the flying capacitor. When in Skip mode, output ripple depends mostly on two parameters: charge transfer between the capacitance values of CFLY and COUT, and the ESR of COUT. The ESR ripple contribution occurs as COUT charges. The charging current creates a negative voltage pulse across the capacitor's ESR that recedes as C OUT charges. At equilibrium, when the voltage on C FLY approaches that on COUT, no charging current flows. Secondly, the ripple contribution due to charge transfer between capacitors creates a pulse as charge flows to COUT. Adding the two terms does not determine peakto-peak ripple because their peaks do not occur at the same time. It is best to use only the dominant term. The expression for the ripple component predominantly due to COUT ESR is: *See Output Ripple vs. Load Current in Typical Operating Characteristics. Applications Information Resistor Selection (Output Voltage Selection) The accuracy of VOUT depends on the accuracy of the voltage biasing the voltage-divider network (R1, R2). Use a separate reference voltage if VIN is an unregulated voltage or if greater accuracy is desired (Figure 4). Adjust the output voltage from -1.5V to -V IN in LIN mode or 0V to -VIN in Skip mode with external resistors R1 and R2 as shown in Figures 1 and 4. In either regulating mode (LIN or Skip), FB servos to 0V. Use the following equations to select R1 and R2 for the desired output voltage: R2 VOUT = - VREF R1 where VREF can be either VIN or some other positive reference source. Typically, choose a voltage-divider current of 50A to minimize the effect of FB input current: R1 = VREF / 50A R2 = -VOUT / 50A _______________________________________________________________________________________ 7 MAX1673 Regulated, 125mA-Output, Charge-Pump DC-DC Inverter V - V ESR VRIPPLE(ESR) = 8 IN OUT 2 COUT f R OUT CFLY OSC where COUT is the output capacitor value, and fMIN is the minimum oscillator frequency (250kHz). See Table 1 for a list of suggested capacitor suppliers. Layout Considerations The MAX1673's high oscillator frequency requires good layout technique, which ensures stability and helps maintain the output voltage under heavy loads. Take the following steps to ensure good layout: The expression for the ripple component predominantly due to charge transfer is: V - V 1 VRIPPLE(ESR) = 2 IN OUT fOSC ROUT (CFLY + C OUT ) * Mount all components as close together as possible. * Place the feedback resistors R1 and R2 close to the FB pin, and minimize the PC trace length at the FB circuit node. * Keep traces short to minimize parasitic inductance and capacitance. * Use a ground plane. where CFLY and COUT are their respective capacitance values, ESRCOUT is the equivalent series resistance of COUT, ROUT is the MAX1673 open-loop output impedance (typically 3.5, and fOSC is the MAX1673 switching frequency (typically 350kHz). If ESRCOUT is very small, as is likely when ceramic capacitors are used, V RIPPLE (TRANSFER) dominates. If ESR is relatively large, as with low-cost tantalum capacitors, then VRIPPLE (ESR) dominates. When operating in LIN mode, use the following equation to approximate peak-to-peak output voltage ripple: VRIPPLE = I OUT 2f OSC C OUT ___________________Chip Information TRANSISTOR COUNT: 386 SUBSTRATE CONNECTED TO: IN + 2IOUT ESRCOUT where COUT is the output capacitor value, ESRCOUT is the output capacitor's ESR, and fOSC is the MAX1673 oscillator frequency (typically 350kHz). To ensure LIN mode stability over the entire temperature range, choose a low-ESR (no more than 100m) output capacitance using the following equation: R1 COUT = 75 x 10 - 6 R1 + R2 IOUT Table 1. Partial Listing of Capacitor Vendors PRODUCTION METHOD MANUFACTURER Surface-Mount Tantalum Surface-Mount Ceramic SERIES PHONE FAX AVX TPS (803) 946-0690 (803) 448-2170 Matsuo 267 (714) 969-2491 (714) 960-6492 Sprague 593D, 595D (603) 224-1961 (603) 224-1430 AVX X7R (803) 946-0590 (803) 626-3123 Matsuo X7R (714) 969-2491 (714) 960-6492 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 1998 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.