LM359 LM359 Dual, High Speed, Programmable, Current Mode (Norton) Amplifiers Literature Number: SNOSBT4B LM359 Dual, High Speed, Programmable, Current Mode (Norton) Amplifiers General Description Features The LM359 consists of two current differencing (Norton) input amplifiers. Design emphasis has been placed on obtaining high frequency performance and providing user programmable amplifier operating characteristics. Each amplifier is broadbanded to provide a high gain bandwidth product, fast slew rate and stable operation for an inverting closed loop gain of 10 or greater. Pins for additional external frequency compensation are provided. The amplifiers are designed to operate from a single supply and can accommodate input common-mode voltages greater than the supply. n User programmable gain bandwidth product, slew rate, input bias current, output stage biasing current and total device power dissipation n High gain bandwidth product (ISET = 0.5 mA) 400 MHz for AV = 10 to 100 30 MHz for AV = 1 n High slew rate (ISET = 0.5 mA) 60 V/s for AV = 10 to 100 30 V/s for AV = 1 n Current differencing inputs allow high common-mode input voltages n Operates from a single 5V to 22V supply n Large inverting amplifier output swing, 2 mV to VCC - 2V n Low spot noise, for f > 1 kHz Applications n n n n n General purpose video amplifiers High frequency, high Q active filters Photo-diode amplifiers Wide frequency range waveform generation circuits All LM3900 AC applications work to much higher frequencies Typical Application Connection Diagram Dual-In-Line Package 00778802 00778801 * * * * AV = 20 dB -3 dB bandwidth = 2.5 Hz to 25 MHz Differential phase error < 1 at 3.58 MHz Top View Order Number LM359M or LM359N See NS Package Number M14A or N14A Differential gain error < 0.5% at 3.58 MHz (c) 2004 National Semiconductor Corporation DS007788 www.national.com LM359 Dual, High Speed, Programmable, Current Mode (Norton) Amplifiers August 2000 LM359 Absolute Maximum Ratings (Note 1) Input Currents, IIN(+) or IIN(-) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Set Currents, ISET(IN) or ISET(OUT) Supply Voltage 10 mADC 2 mADC Operating Temperature Range LM359 22 VDC 0C to +70C Storage Temperature Range or 11 VDC -65C to +150C Lead Temperature Power Dissipation (Note 2) (Soldering, 10 sec.) J Package 1W N Package 750 mW Dual-In-Line Package J Package +150C Small Outline Package N Package +125C 260C Soldering Information Maximum TJ Soldering (10 sec.) Thermal Resistance J Package 260C Vapor Phase (60 sec.) 215C Infrared (15 sec.) 220C See AN-450 "Surface Mounting Methods and Their Effect on Product Reliability" for other methods of soldering surface mount devices. jA 147C/W still air 110C/W with 400 linear feet/min air flow ESD rating to be determined. N Package jA 100C/W still air 75C/W with 400 linear feet/min air flow Electrical Characteristics ISET(IN) = ISET(OUT) = 0.5 mA, Vsupply = 12V, TA = 25C unless otherwise noted Parameter Conditions LM359 Min Open Loop Voltage Vsupply = 12V, RL = 1k, f = 100 Hz Gain TA = 125C Bandwidth RIN = 1 k, Ccomp = 10 pF RIN = 50 to 200 62 Typ Units Max 72 dB 68 dB 15 30 MHz 200 400 MHz Unity Gain Gain Bandwidth Product Gain of 10 to 100 Slew Rate Unity Gain RIN = 1 k, Ccomp = 10 pF 30 V/s Gain of 10 to 100 RIN < 200 60 V/s f = 100 Hz to 100 kHz, RL = 1k -80 dB Amplifier to Amplifier Coupling Mirror Gain at 2 mA IIN(+), ISET = 5 A, TA = 25C 0.9 1.0 1.1 A/A (Note 3) at 0.2 mA IIN(+), ISET = 5 A 0.9 1.0 1.1 A/A 0.9 1.0 1.1 A/A 3 5 % Over Temp. at 20 A IIN(+), ISET = 5 A Over Temp. Mirror Gain at 20 A to 0.2 mA IIN(+) (Note 3) Over Temp, ISET = 5 A Input Bias Current Inverting Input, TA = 25C 8 Over Temp. 15 A 30 A Input Resistance (re) Inverting Input 2.5 k Output Resistance IOUT = 15 mA rms, f = 1 MHz 3.5 Output Voltage Swing RL = 600 10.3 V VOUT High IIN(-) and IIN(+) Grounded VOUT Low IIN(-) = 100 A, IIN(+) = 0 www.national.com 9.5 2 2 50 mV LM359 Electrical Characteristics (Continued) ISET(IN) = ISET(OUT) = 0.5 mA, Vsupply = 12V, TA = 25C unless otherwise noted Parameter Conditions LM359 Units Min Typ Max 16 40 mA 4.7 mA 3 mA Output Currents Source IIN(-) and IIN(+) Grounded, RL = 100 Sink (Linear Region) Vcomp-0.5V = VOUT = 1V, IIN(+) = 0 Sink (Overdriven) IIN(-) = 100 A, IIN(+) = 0, 1.5 VOUT Force = 1V Supply Current Non-Inverting Input 18.5 22 mA Grounded, RL = Power Supply Rejection f = 120 Hz, IIN(+) Grounded 40 50 dB (Note 4) Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Note 2: See Maximum Power Dissipation graph. Note 3: Mirror gain is the current gain of the current mirror which is used as the non-inverting input. Mirror Gain is the % change in AI for two different mirror currents at any given temperature. Note 4: See Supply Rejection graphs. Typical Performance Characteristics Open Loop Gain Open Loop Gain 00778840 00778839 Note: Shaded area refers to LM359 Open Loop Gain Gain Bandwidth Product 00778842 00778841 3 www.national.com LM359 Typical Performance Characteristics (Continued) Gain and Phase Feedback Gain = - 100 Slew Rate 00778844 00778843 Inverting Input Bias Current Inverting Input Bias Current 00778846 00778845 Note: Shaded area refers to LM359 Mirror Gain Mirror Gain 00778847 00778848 Note: Shaded area refers to LM359 www.national.com 4 LM359 Typical Performance Characteristics (Continued) Mirror Gain Mirror Current 00778850 00778849 Note: Shaded area refers to LM359 Supply Current Supply Rejection 00778852 00778851 Supply Rejection Output Sink Current 00778853 00778854 5 www.national.com LM359 Typical Performance Characteristics (Continued) Output Swing Output Impedance 00778855 00778856 Amplifier to Amplifier Coupling (Input Referred) Noise Voltage 00778858 00778857 Maximum Power Dissipation 00778859 Note: Shaded area refers to LM359J/LM359N This significant improvement in frequency response is the result of using a common-emitter/common-base (cascode) gain stage which is typical in many discrete and integrated video and RF circuit designs. Another versatile aspect of these amplifiers is the ability to externally program many internal amplifier parameters to suit the requirements of a wide variety of applications in which this type of amplifier can be used. Application Hints The LM359 consists of two wide bandwidth, decompensated current differencing (Norton) amplifiers. Although similar in operation to the original LM3900, design emphasis for these amplifiers has been placed on obtaining much higher frequency performance as illustrated in Figure 1. www.national.com 6 output DC level to be whatever value necessary (within the output voltage swing of the amplifier) to provide this DC reference current, Figure 2. (Continued) 00778807 00778806 FIGURE 1. DC BIASING The LM359 is intended for single supply voltage operation which requires DC biasing of the output. The current mirror circuitry which provides the non-inverting input for the amplifier also facilitates DC biasing the output. The basic operation of this current mirror is that the current (both DC and AC) flowing into the non-inverting input will force an equal amount of current to flow into the inverting input . The mirror gain (AI) specification is the measure of how closely these two currents match. For more details see National Application Note AN-72. DC biasing of the output is accomplished by establishing a reference DC current into the (+) input, IIN(+), and requiring the output to provide the (-) input current. This forces the FIGURE 2. The DC input voltage at each input is a transistor VBE (. 0.6 VDC) and must be considered for DC biasing. For most applications, the supply voltage, V+, is suitable and convenient for establishing IIN(+). The inverting input bias current, Ib(-), is a direct function of the programmable input stage current (see current programmability section) and to obtain predictable output DC biasing set IIN(+) 10Ib(-). 7 www.national.com LM359 Application Hints LM359 Application Hints (Continued) The following figures illustrate typical biasing schemes for AC amplifiers using the LM359: 00778810 00778808 FIGURE 5. nVBE Biasing The nVBE biasing configuration is most useful for low noise applications where a reduced input impedance can be accommodated (see typical applications section). FIGURE 3. Biasing an Inverting AC Amplifier OPERATING CURRENT PROGRAMMABILITY (ISET) The input bias current, slew rate, gain bandwidth product, output drive capability and total device power consumption of both amplifiers can be simultaneously controlled and optimized via the two programming pins ISET(OUT) and ISET(IN). ISET(OUT) The output set current (ISET(OUT)) is equal to the amount of current sourced from pin 1 and establishes the class A biasing current for the Darlington emitter follower output stage. Using a single resistor from pin 1 to ground, as shown in Figure 6, this current is equal to: 00778809 FIGURE 4. Biasing a Non-Inverting AC Amplifier 00778811 FIGURE 6. Establishing the Output Set Current The output set current can be adjusted to optimize the amount of current the output of the amplifier can sink to drive load capacitance and for loads connected to V+. The maximum output sinking current is approximately 10 times ISET(OUT) . This set current is best used to reduce the total device supply current if the amplifiers are not required to drive small load impedances. ISET(IN) www.national.com 8 PROGRAMMING WITH A SINGLE RESISTOR (Continued) Operating current programming may also be accomplished using only one resistor by letting ISET(IN) equal ISET(OUT). The programming current is now referred to as ISET and it is created by connecting a resistor from pin 1 to pin 8 (Figure 8). The input set current ISET(IN) is equal to the current flowing into pin 8. A resistor from pin 8 to V+ sets this current to be: 00778812 00778813 ISET(IN) = ISET(OUT) = ISET FIGURE 7. Establishing the Input Set Current FIGURE 8. Single Resistor Programming of ISET ISET(IN) is most significant in controlling the AC characteristics of the LM359 as it directly sets the total input stage current of the amplifiers which determines the maximum slew rate, the frequency of the open loop dominant pole, the input resistance of the (-) input and the biasing current Ib(-). All of these parameters are significant in wide band amplifier design. The input stage current is approximately 3 times ISET(IN) and by using this relationship the following first order approximations for these AC parameters are: This configuration does not affect any of the internal set current dependent parameters differently than previously discussed except the total supply current which is now equal to: Isupply . 37 x ISET Care must be taken when using resistors to program the set current to prevent significantly increasing the supply voltage above the value used to determine the set current. This would cause an increase in total supply current due to the resulting increase in set current and the maximum device power dissipation could be exceeded. The set resistor value(s) should be adjusted for the new supply voltage. One method to avoid this is to use an adjustable current source which has voltage compliance to generate the set current as shown in Figure 9. where Ccomp is the total capacitance from the compensation pin (pin 3 or pin 13) to ground, AVOL is the low frequency open loop voltage gain in V/V and an ambient temperature of 25C is assumed (KT/q = 26 mV and typ = 150). ISET(IN) also controls the DC input bias current by the expression: 00778814 which is important for DC biasing considerations. The total device supply current (for both amplifiers) is also a direct function of the set currents and can be approximated by: Isupply . 27 x ISET(OUT) + 11 x ISET(IN) FIGURE 9. Current Source Programming of ISET with each set current programmed by individual resistors. This circuit allows ISET to remain constant over the entire supply voltage range of the LM359 which also improves power supply ripple rejection as illustrated in the Typical Performance Characteristics. It should be noted, however, that the current through the LM334 as shown will change linearly with temperature but this can be compensated for (see LM334 data sheet). 9 www.national.com LM359 Application Hints LM359 Application Hints (Continued) Pin 1 must never be shorted to ground or pin 8 never shorted to V+ without limiting the current to 2 mA or less to prevent catastrophic device failure. CONSIDERATIONS FOR HIGH FREQUENCY OPERATION The LM359 is intended for use in relatively high frequency applications and many factors external to the amplifier itself must be considered. Minimization of stray capacitances and their effect on circuit operation are the primary requirements. The following list contains some general guidelines to help accomplish this end: 1. Keep the leads of all external components as short as possible. 2. Place components conducting signal current from the output of an amplifier away from that amplifier's noninverting input. Use reasonably low value resistances for gain setting and biasing. Use of a ground plane is helpful in providing a shielding effect between the inputs and from input to output. Avoid using vector boards. Use a single-point ground and single-point supply distribution to minimize crosstalk. Always connect the two grounds (one from each amplifier) together. Avoid use of long wires ( > 2") but if necessary, use shielded wire. 3. 4. 5. 6. 7. 00778815 Cf = 1 pF to 5 pF for stability FIGURE 10. Best Method of Compensation Another method of compensation is to increase the effective value of the internal compensation capacitor by adding capacitance from the COMP pin of an amplifier to ground. An external 20 pF capacitor will generally compensate for all gain settings but will also reduce the gain bandwidth product and the slew rate. These same results can also be obtained by reducing ISET(IN) if the full capabilities of the amplifier are not required. This method is termed over-compensation. Another area of concern from a stability standpoint is that of capacitive loading. The amplifier will generally drive capacitive loads up to 100 pF without oscillation problems. Any larger C loads can be isolated from the output as shown in Figure 11. Over-compensation of the amplifier can also be used if the corresponding reduction of the GBW product can be afforded. Bypass the supply close to the device with a low inductance, low value capacitor (typically a 0.01 F ceramic) to create a good high frequency ground. If long supply leads are unavoidable, a small resistor (10) in series with the bypass capacitor may be needed and using shielded wire for the supply leads is also recommended. COMPENSATION The LM359 is internally compensated for stability with closed loop inverting gains of 10 or more. For an inverting gain of less than 10 and all non-inverting amplifiers (the amplifier always has 100% negative current feedback regardless of the gain in the non-inverting configuration) some external frequency compensation is required because the stray capacitance to ground from the (-) input and the feedback resistor add additional lagging phase within the feedback loop. The value of the input capacitance will typically be in the range of 6 pF to 10 pF for a reasonably constructed circuit board. When using a feedback resistance of 30 k or less, the best method of compensation, without sacrificing slew rate, is to add a lead capacitor in parallel with the feedback resistor with a value on the order of 1 pF to 5 pF as shown in Figure 10 . 00778816 FIGURE 11. Isolating Large Capacitive Loads In most applications using the LM359, the input signal will be AC coupled so as not to affect the DC biasing of the amplifier. This gives rise to another subtlety of high frequency circuits which is the effective series inductance (ESL) of the coupling capacitor which creates an increase in the impedance of the capacitor at high frequencies and can cause an unexpected gain reduction. Low ESL capacitors like solid tantalum for large values of C and ceramic for smaller values are recommended. A parallel combination of the two types is even better for gain accuracy over a wide frequency range. www.national.com 10 LM359 Application Hints (Continued) AMPLIFIER DESIGN EXAMPLES The ability of the LM359 to provide gain at frequencies higher than most monolithic amplifiers can provide makes it most useful as a basic broadband amplification stage. The design of standard inverting and non-inverting amplifiers, though different than standard op amp design due to the current differencing inputs, also entail subtle design differences between the two types of amplifiers. These differences will be best illustrated by design examples. For these examples a practical video amplifier with a passband of 8 Hz to 10 MHz and a gain of 20 dB will be used. It will be assumed that the input will come from a 75 source and proper signal termination will be considered. The supply voltage is 12 VDC and single resistor programming of the operating current, ISET, will be used for simplicity. Rf(MAX) can now be found: This value should not be exceeded for predictable DC biasing. Select Rs to be large enough so as not to appreciably load the input termination resistance: Rs 750; Let Rs = 750 5. Select Rf for appropriate gain: 4. AN INVERTING VIDEO AMPLIFIER 1. Basic circuit configuration: 7.5 k is less than the calculated Rf(MAX) so DC predictability is insured. 6. Now Rb can be found by: 00778817 2. 3. Since Rf = 7.5k, for the output to be biased to 5.1 VDC, the reference current IIN(+) must be: Determine the required ISET from the characteristic curves for gain bandwidth product. GBWMIN= 10 x 10 MHz = 100 MHz For a flat response to 10 MHz a closed loop response to two octaves above 10 MHz (40 MHz) will be sufficient. Actual GBW = 10 x 40 MHz = 400 MHz ISET required = 0.5 mA 7. Select Ci to provide the proper gain for the 8 Hz minimum input frequency: A larger value of Ci will allow a flat frequency response down to 8 Hz and a 0.01 F ceramic capacitor in parallel with Ci will maintain high frequency gain accuracy. Determine maximum value for Rf to provide stable DC biasing 8. Test for peaking of the frequency response and add a feedback "lead" capacitor to compensate if necessary. Optimum output DC level for maximum symmetrical swing without clipping is: 11 www.national.com LM359 Application Hints (Continued) A NON-INVERTING VIDEO AMPLIFIER For this case several design considerations must be dealt with. * The output voltage (AC and DC) is strictly a function of the size of the feedback resistor and the sum of AC and DC "mirror current" flowing into the (+) input. * The amplifier always has 100% current feedback so external compensation is required. Add a small (1 pF-5 pF) feedback capacitance to leave the amplifier's open loop response and slew rate unaffected. * To prevent saturating the mirror stage the total AC and DC current flowing into the amplifier's (+) input should be less than 2 mA. * The output's maximum negative swing is one diode above ground due to the VBE diode clamp at the (-) input. Final Circuit Using Standard 5% Tolerance Resistor Values: 00778818 Circuit Performance: 00778819 Vo(DC) = 5.1V Differential phase error < 1 for 3.58 MHz fIN Differential gain error < 0.5% for 3.58 MHz fIN f-3 dB low = 2.5 Hz www.national.com 12 4. (Continued) DESIGN EXAMPLE 5. For Av = 10; Rf is set to 7.5 k. 6. The optimum output DC level for symmetrical AC swing is: eIN = 50 mV (MAX), fIN = 10 MHz (MAX), desired circuit BW = 20 MHz, AV = 20 dB, driving source impedance = 75, V+ = 12V. 1. So as not to appreciably load the 75 input termination resistance the value of (Rs + re) is set to 750. Basic circuit configuration: 7. The DC feedback current must be: DC biasing predictability will be insured because 640 A is greater than the minimum of ISET/5 or 100 A. For gain accuracy the total AC and DC mirror current should be less than 2 mA. For this example the maximum AC mirror current will be: 00778820 2. 3. Select ISET to provide adequate amplifier bandwidth so that the closed loop bandwidth will be determined by Rf and Cf. To do this, the set current should program an amplifier open loop gain of at least 20 dB at the desired closed loop bandwidth of the circuit. For this example, an ISET of 0.5 mA will provide 26 dB of open loop gain at 20 MHz which will be sufficient. Using single resistor programming for ISET: therefore the total mirror current range will be 574 A to 706 A which will insure gain accuracy. 8. Rb can now be found: 9. Since Rs + re will be 750 and re is fixed by the DC mirror current to be: Since the closed loop bandwidth will be determined by Rs must be 750-40 or 710 which can be a 680 resistor in series with a 30 resistor which are standard 5% tolerance resistor values. to obtain a 20 MHz bandwidth, both Rf and Cf should be kept small. It can be assumed that Cf can be in the range of 1 pF to 5 pF for carefully constructed circuit boards to insure stability and allow a flat frequency response. This will limit the value of Rf to be within the range of: 10. As a final design step, Ci must be selected to pass the lower passband frequency corner of 8 Hz for this example. A larger value may be used and a 0.01 F ceramic capacitor in parallel with Ci will maintain high frequency gain accuracy. Also, for a closed loop gain of +10, Rf must be 10 times Rs + re where re is the mirror diode resistance. 13 www.national.com LM359 Application Hints LM359 Application Hints (Continued) Final Circuit Using Standard 5% Tolerance Resistor Values 00778821 Circuit Performance 00778822 Vo(DC) = 5.4V Differential phase error < 0.5 Differential gain error < 2% f-3 dB low = 2.5 Hz www.national.com 14 prevent damaging the current mirror input diode, the mirror current should always be limited to 10 mA, or less, which is important if the input is susceptible to high voltage transients. The voltage at any of the inputs must not be forced more negative than -0.7V without limiting the current to 10 mA. (Continued) GENERAL PRECAUTIONS The LM359 is designed primarily for single supply operation but split supplies may be used if the negative supply voltage is well regulated as the amplifiers have no negative supply rejection. The supply voltage must never be reversed to the device; however, plugging the device into a socket backwards would then connect the positive supply voltage to the pin that has no internal connection (pin 5) which may prevent inadvertent device failure. The total device power dissipation must always be kept in mind when selecting an operating supply voltage, the programming current, ISET, and the load resistance, particularly when DC coupling the output to a succeeding stage. To Typical Applications DC Coupled Inputs Inverting 00778823 Non-Inverting 00778824 * Eliminates the need for an input coupling capacitor * Input DC level must be stable and can exceed the supply voltage of the LM359 provided that maximum input currents are not exceeded. 15 www.national.com LM359 Application Hints LM359 Typical Applications (Continued) Adding a JFET Input Stage Noise Reduction using nVBE Biasing 00778825 nVBE Biasing with a Negative Supply 00778828 00778826 * R1 and C2 provide additional filtering of the negative biasing supply Typical Input Referred Noise Performance 00778827 www.national.com 16 * * * * * FET input voltage mode op amp For AV = +1; BW = 40 MHz, Sr = 60 V/s; CC = 51 pF For AV = +11; BW = 24 MHz, Sr = 130 V/s; CC = 5 pF For AV = +100; BW = 4.5 MHz, Sr = 150 V/s; CC = 2 pF VOS is typically < 25 mV; 100 potentiometer allows a VOS adjust range of 200 mV * Inputs must be DC biased for single supply operation LM359 Typical Applications (Continued) Photo Diode Amplifier 00778829 D1 RCA N-Type Silicon P-I-N Photodiode * Frequency response of greater than 10 MHz * If slow rise and fall times can be tolerated the gate on the output can be removed. In this case the rise and the fall time of the LM359 is 40 ns. * TPDL = 45 ns, TPDH = 50 ns - T2L output 17 www.national.com LM359 Typical Applications (Continued) Balanced Line Driver 00778830 * * * * 1 MHz-3 dB bandwidth with gain of 10 and 0 dbm into 600 0.3% distortion at full bandwidth; reduced to 0.05% with bandwidth of 10 kHz Will drive CL = 1500 pF with no additional compensation, 0.01 F with Ccomp = 180 pF 70 dB signal to noise ratio at 0 dbm into 600, 10 kHz bandwidth www.national.com 18 (Continued) LM359 Typical Applications Voltage Controlled Oscillator Difference Amplifier 00778831 00778832 * CMRR is adjusted for max at expected CM input signal * 5 MHz operation * T2L output * Wide bandwidth * 70 dB CMRR typ * Wide CM input voltage range 19 www.national.com LM359 Typical Applications (Continued) Phase Locked Loop 00778833 * Up to 5 MHz operation * T2L compatible input All diodes = 1N914 www.national.com 20 LM359 Typical Applications (Continued) Squarewave Generator 00778834 f = 1 MHz Output is TTL compatible Frequency is adjusted by R1 & C (R1 ! R2) Pulse Generator 00778836 Output is TTL compatible Duty cycle is adjusted by R1 Frequency is adjusted by C f = 1 MHz Duty cycle = 20% 21 www.national.com LM359 Typical Applications (Continued) Crystal Controlled Sinewave Oscillator 00778837 Vo = 500 mVp-p f = 9.1 MHz THD < 2.5% High Performance 2 Amplifier Biquad Filter(s) 00778835 * The high speed of the LM359 allows the center frequency Qo product of the filter to be: fox Qo 5 MHz * The above filter(s) maintain performance over wide temperature range * One half of LM359 acts as a true non-inverting integrator so only 2 amplifiers (instead of 3 or 4) are needed for the biquad filter structure www.national.com 22 LM359 Typical Applications (Continued) DC Biasing Equations for V01(DC) . V02(DC) .V+/2 Type I Type II Type III Analysis and Design Equations Type VO1 VO2 Ci Ri2 Ri1 Qo fZ(notch) Ho(LP) Ho(BP) Ho(HP) Ho(BR) I BP LP O Ri2 fo RQ/R -- R/Ri2 RQ/Ri2 -- -- II HP BP Ci RQ/R -- -- RQCi/RC Ci/C -- III Notch/ BR -- Ci Ri1 RQ/R -- -- -- Triangle Waveform Generator 00778838 V2 output is TTL compatible R2 adjusts for symmetry of the triangle waveform Frequency is adjusted with R5 and C 23 www.national.com www.national.com 24 Schematic Diagram 00778803 LM359 LM359 Physical Dimensions inches (millimeters) unless otherwise noted S.O. Package (M) Order Number LM359M or LM359MX NS Package Number M14A Molded Dual-In-Line Package (N) Order Number LM359N NS Package Number N14A 25 www.national.com LM359 Dual, High Speed, Programmable, Current Mode (Norton) Amplifiers Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated