HDSP-56xC Series 13 mm Slim Font Seven Segment Displays Data Sheet Description The Slim Font Seven Segment Displays incorporates a new slim font character design. This slim font features narrow width, specially mitered segments to give fuller appearance to the illuminated character. Faces of these displays are painted a neutral gray for enhanced on/off contrast. All devices are available in either common anode or common cathode configuration with right hand decimal point. Devices As AlInGaP Red Description HDSP-561C HDSP-563C Common Anode Common Cathode Features * As AlInGaP red color * Gray Face Paint Gray package gives optimum contrast * Design flexibility Common anode or common cathode * Excellent appearance * Slim font design * Mitered corners, evenly illuminated segments Part Numbering System 5082 -X X X X-X X X X X HDSP-X X X X-X X X X X Mechanical Options[1] 00: No Mechanical Option Color Bin Options[1,2] 0: No Color Bin Limitation Maximum Intensity Bin[1,2] 0: No Maximum Intensity Bin Limitation Minimum Intensity Bin[1,2] 0: No Minimum Intensity Bin Limitation Device Configuration/Color[1] C: AlInGaP Red Device Specific Configuration[1] Refer to Respective Datasheet Package[1] Refer to Respective Datasheet Notes: 1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Avago representative for details. 2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information. 2 Package Dimensions and Internal Circuit 45 7.40 (0.292) 10 1.25 (0.049) 13.00 (0.512) 15.24 0.3 (0.600) 17.50 0.3/-0.25 (0.689) 0.30 0.08 TYP. (0.012) 1.25 O (0.049) 6.40 0.25 (0.252) 3.60 0.3 (0.142) 7.00 0.25 (0.276) 12.25 0.25 (0.482) 10 8 9 6 7 a f b g 3.59 0.3 TYP. (0.141) 0.50 0.08 (0.020) e c 2.54 0.3 TYP. (0.100) 1 NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. UNLESS OTHERWISE STATED, TOLERANCES ARE 0.25 MM. Pin 1 2 3 4 5 6 7 8 9 10 3 Function E D Common A/C C DP B A Common A/C F G DP d 2 3 4 5 Absolute Maximum Ratings at TA = 25C Description Symbol HDSP-561C/563C Units DC Forward Current per Segment or DP[1,2,3] Peak Forward Current per Segment or DP[2,3] IF IPEAK 50 100 mA mA Average Forward Current[3] Reverse Voltage per Segment or DP (IR = 100 A) IAVE VR 30 5 mA V Operating Temperature Storage Temperature TO TS -40 to +105 -40 to +120 C C Wave Soldering Conditions Temperature Time 250 3 C s Notes: 1. Derate linearly as shown in Figure 1. 2. For long term performance with minimal light output degradation, drive currents between 10 mA and 30 mA are recommended. For more information on recommended drive conditions, please refer to Application Brief I-024 (5966-3087E). 3. Operating at currents below 1 mA is not recommended. Please contact your local representative for further information. Optical/Electrical Characteristics at TA = 25C Device Series HDSP561C 563C Parameter Symbol Min. Forward Voltage Reverse Voltage Peak Wavelength IV VR PEAK 5 Dominant Wavelength[3] Spectral Halfwidth d 1/2 Speed of Response S 20 ns Capacitance C 40 pF Intensity Bin Limits[1] (mcd at 10 mA) Bin Name T U Min.[2] 18.000 25.001 Max.[2] 25.000 36.000 Notes: 1. Bin categories are established for classification of products. Products may not be available in all bin categories. 2. Tolerance for each bin limit is 10%. 4 Typ. Max. Units Test Conditions 1.90 2.40 V V nm IF = 20 mA IF = 100 A Peak Wavelength of Spectral Distribution at IF = 20 mA 630 nm nm 635 622.5 626 40 Wavelength Width at Spectral Distribution 1/2 Power Point at IF = 20 mA Exponential Time Constant, e-ts VF = 0, f = 1 MHz 40 30 20 10 0 20 0 40 60 80 100 120 TA - AMBIENT TEMPERATURE - C 100 80 60 40 20 0 0.0 1.0 1.5 2.0 2.5 VF - FORWARD VOLTAGE - V Figure 2. Forward current vs. forwrad voltage. Figure 1. Maximum forward current vs. ambient temperature. Derating based on TJMAX = 130C. RELATIVE EFFICIENCY (NORMALIZED TO 1 AT 10 mA) 3.5 120 RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 10 mA) 50 IF - FORWARD CURRENT PER SEGMENT - mA IF - MAXIMUM AVERAGE CURRENT - mA 60 3.0 3.0 2.5 2.0 1.5 1.0 0.5 0 0 10 20 30 40 Contrast Enhancement 1.2 For information on contrast enhancement, please see Application Note 1015. 0.8 0.6 Soldering/Cleaning 0.4 0.2 0 60 Figure 3. Relative luminous intensity vs. DC forward current. 1.4 1.0 50 IF - FORWARD CURRENT PER SEGMENT - mA 0 10 20 30 40 50 60 IPEAK - PEAK FORWARD CURRENT PER SEGMENT - mA Figure 4. Relative efficiency (luminous intensity per unit current) vs. peak current. Cleaning agents from ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. For information on soldering LEDs, please refer to Application Note 1027. 5 For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright (c) 2006 Avago Technologies Limited. All rights reserved. 5988-4823EN May 31, 2006