LM118-N, LM218-N, LM318-N
www.ti.com
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
LM118-N/lm218-N/LM318-N Operational Amplifiers
Check for Samples: LM118-N,LM218-N,LM318-N
1FEATURES DESCRIPTION
The LM118 series are precision high speed
2• 15 MHz Small Signal Bandwidth operational amplifiers designed for applications
• Ensured 50V/μs Slew Rate requiring wide bandwidth and high slew rate. They
• Maximum Bias Current of 250 nA feature a factor of ten increase in speed over general
purpose devices without sacrificing DC performance.
• Operates from Supplies of ±5V to ±20V
• Internal Frequency Compensation The LM118 series has internal unity gain frequency
compensation. This considerably simplifies its
• Input and Output Overload Protected application since no external components are
• Pin Compatible with General Purpose Op necessary for operation. However, unlike most
Amps internally compensated amplifiers, external frequency
compensation may be added for optimum
performance. For inverting applications, feedforward
compensation will boost the slew rate to over
150V/μs and almost double the bandwidth.
Overcompensation can be used with the amplifier for
greater stability when maximum bandwidth is not
needed. Further, a single capacitor can be added to
reduce the 0.1% settling time to under 1 μs.
The high speed and fast settling time of these op
amps make them useful in A/D converters, oscillators,
active filters, sample and hold circuits, or general
purpose amplifiers. These devices are easy to apply
and offer an order of magnitude better AC
performance than industry standards such as the
LM709.
The LM218-N is identical to the LM118 except that
the LM218-N has its performance specified over a
−25°C to +85°C temperature range. The LM318-N is
specified from 0°C to +70°C.
Fast Voltage Follower
Do not hard-wire as voltage follower (R1 ≥5 kΩ)
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 1998–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LM118-N, LM218-N, LM318-N
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
Supply Voltage ±20V
Power Dissipation (3) 500 mW
Differential Input Current (4) ±10 mA
Input Voltage (5) ±15V
Output Short-Circuit Duration Continuous
Operating Temperature Range
lm118-n −55°C to +125°C
LM218-N −25°C to +85°C
LM318-N 0°C to +70°C
Storage Temperature Range −65°C to +150°C
Lead Temperature (Soldering, 10 sec.)
TO-99 Package 300°C
PDIP Package 260°C
Soldering Information
Dual-In-Line Package
Soldering (10 sec.) 260°C
SOIC Package
Vapor Phase (60 sec.) 215°C
Infrared (15 sec.) 220°C
ESD Tolerance (6) 2000V
(1) Refer to RETS118X for LM118H and LM118J military specifications.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(3) The maximum junction temperature of the lm118-n is 150°C, the LM218-N is 110°C, and the LM318-N is 110°C. For operating at
elevated temperatures, devices in the LMC package must be derated based on a thermal resistance of 160°C/W, junction to ambient, or
20°C/W, junction to case. The thermal resistance of the dual-in-line package is 100°C/W, junction to ambient.
(4) The inputs are shunted with back-to-back diodes for overvoltage protection. Therefore, excessive current will flow if a differential input
voltage in excess of 1V is applied between the inputs unless some limiting resistance is used.
(5) For supply voltages less than ±15V, the absolute maximum input voltage is equal to the supply voltage.
(6) Human body model, 1.5 kΩin series with 100 pF.
Electrical Characteristics (1)
Parameter Conditions LM118-N/LM218-N LM318-N Units
Min Typ Max Min Typ Max
Input Offset Voltage TA= 25°C 2 4 4 10 mV
Input Offset Current TA= 25°C 6 50 30 200 nA
Input Bias Current TA= 25°C 120 250 150 500 nA
Input Resistance TA= 25°C 1 3 0.5 3 MΩ
Supply Current TA= 25°C 5 8 5 10 mA
Large Signal Voltage Gain TA= 25°C, VS= ±15V 50 200 25 200 V/mV
VOUT = ±10V, RL≥2 kΩ
Slew Rate TA= 25°C, VS= ±15V, AV= 1 50 70 50 70 V/μs
(2)
Small Signal Bandwidth TA= 25°C, VS= ±15V 15 15 MHz
Input Offset Voltage 6 15 mV
Input Offset Current 100 300 nA
(1) These specifications apply for ±5V ≤VS≤±20V and −55°C ≤TA≤+125°C (lm118-n), −25°C ≤TA≤+85°C (LM218-N), and 0°C ≤TA≤
+70°C (LM318-N). Also, power supplies must be bypassed with 0.1 μF disc capacitors.
(2) Slew rate is tested with VS= ±15V. The lm118-n is in a unity-gain non-inverting configuration. VIN is stepped from −7.5V to +7.5V and
vice versa. The slew rates between −5.0V and +5.0V and vice versa are tested and specified to exceed 50V/μs.
2Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
www.ti.com
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
Electrical Characteristics (1) (continued)
Parameter Conditions LM118-N/LM218-N LM318-N Units
Min Typ Max Min Typ Max
Input Bias Current 500 750 nA
Supply Current TA= 125°C 4.5 7 mA
Large Signal Voltage Gain VS= ±15V, VOUT = ±10V 25 20 V/mV
RL≥2 kΩ
Output Voltage Swing VS= ±15V, RL= 2 kΩ±12 ±13 ±12 ±13 V
Input Voltage Range VS= ±15V ±11.5 ±11. V
5
Common-Mode Rejection Ratio 80 100 70 100 dB
Supply Voltage Rejection Ratio 70 80 65 80 dB
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
LM118-N, LM218-N
Input Current Voltage Gain
Figure 1. Figure 2.
Power Supply Rejection Input Noise Voltage
Figure 3. Figure 4.
Common Mode Rejection Supply Current
Figure 5. Figure 6.
4Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
www.ti.com
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
LM118-N, LM218-N Closed Loop Output
Impedance Current Limiting
Figure 7. Figure 8.
Input Current Unity Gain Bandwidth
Figure 9. Figure 10.
Voltage Follower Slew Rate Inverter Settling Time
Figure 11. Figure 12.
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
LM118-N, LM218-N
Large Signal Frequency Response Open Loop Frequency Response
Figure 13. Figure 14.
Voltage Follower Pulse Response Large Signal Frequency Response
Figure 15. Figure 16.
Open Loop Frequency Response Inverter Pulse Response
Figure 17. Figure 18.
6Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
www.ti.com
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
Typical Performance Characteristics
LM318-N
Input Current Voltage Gain
Figure 19. Figure 20.
Power Supply Rejection Input Noise Voltage
Figure 21. Figure 22.
Common Mode Rejection Supply Current
Figure 23. Figure 24.
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
LM318-N Closed Loop Output Impedance Current Limiting
Figure 25. Figure 26.
Input Current Unity Gain Bandwidth
Figure 27. Figure 28.
Voltage Follower Slew Rate Inverter Settling Time
Figure 29. Figure 30.
8Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
www.ti.com
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
Typical Performance Characteristics (continued)
LM318-N Large Signal Frequency Response Open Loop Frequency Response
Figure 31. Figure 32.
Voltage Follower Pulse Response Large Signal Frequency Response
Figure 33. Figure 34.
Open Loop Frequency Response Inverter Pulse Response
Figure 35. Figure 36.
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
www.ti.com
AUXILIARY CIRCUITS
Figure 39. Offset Balancing
*Balance circuit necessary for increased
slew.
Slew rate typically 150V/μs.
Figure 37. Feedforward Compensation
for Greater Inverting Slew Rate
Figure 40. Isolating Large Capacitive Loads
Figure 41. Overcompensation
Slew and settling time to 0.1% for a 10V
step change is 800 ns.
Figure 38. Compensation for Minimum Settling
Time
10 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
www.ti.com
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
TYPICAL APPLICATIONS
Do not hard-wire as voltage follower (R1 ≥5 kΩ)
Figure 42. Fast Voltage Follower
CF= Large
(CF≥50 pF)
*Do not hard-wire as integrator or slow inverter; insert a 10k-5 pF network in series with the input, to prevent
oscillation.
Do not hard-wire as voltage follower (R1 ≥5 kΩ)
Figure 43.
Figure 45. Differential Amplifie
Figure 44. Fast Summing Amplifier
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
www.ti.com
Figure 46. Fast Sample and Hold
*Optional—Reduces settling time.
Figure 47. D/A Converter Using Ladder Network
12 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
www.ti.com
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
ΔOutput zero.
*“Y” zero
+“X” zero
‡Full scale adjust.
Figure 48. Four Quadrant Multiplier
*Optional—Reduces settling time.
Figure 49. D/A Converter Using Binary Weighted Network
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
www.ti.com
Figure 50. Fast Summing Amplifier with Low Input Current
Figure 51. Wein Bridge Sine Wave Oscillator
Figure 52. Instrumentation Amplifier
14 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
www.ti.com
Pin Diagram
Available per JM38510/10107.
Available per JM38510/10107.
Dual-In-Line Package
(Top View) Dual-In-Line Package
See Package Number J (R-GDIP-T14) (Top View)
See Package Number NAB008A, D (R-PDSO-G8),
or P (R-PDIP-T8)
Pin connections shown on schematic diagram and typical applications are for TO-99 package.
TO-99 Package
(Top View)
See Package Number LMC (O-MBCY-W8)
16 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM118-N LM218-N LM318-N
LM118-N, LM218-N, LM318-N
www.ti.com
SNOSBS8C –MARCH 1998–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision B (March 2013) to Revision C Page
• Changed layout of National Data Sheet to TI format .......................................................................................................... 16
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM118-N LM218-N LM318-N
PACKAGE OPTION ADDENDUM
www.ti.com 14-Jun-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM118H ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -55 to 125 ( LM118H ~ LM118H)
LM118H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 125 ( LM118H ~ LM118H)
LM318M NRND SOIC D 8 95 TBD Call TI Call TI 0 to 70 LM
318M
LM318M/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM
318M
LM318MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM
318M
LM318N/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 70 LM
318N
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 14-Jun-2017
Addendum-Page 2
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM318MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM318MX/NOPB SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
