PRODUCT: ZEN132V130A24LS PolyZen Polymer Enhanced Zener Diode Micro-Assemblies 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com DOCUMENT: SCD 26665 REV LETTER: F REV DATE: OCTOBER 29, 2008 PAGE NO.: 1 OF 8 Raychem Circuit Protection Products Specification Status: Released GENERAL DESCRIPTION Tyco Electronics PolyZen devices are polymer enhanced, precision Zener diode micro-assemblies. They offer resettable protection against multi-Watt fault events without the need for multi-Watt heat sinks. The Zener diode used for voltage clamping in a PolyZen micro-assembly was selected due to its relatively flat voltage vs current response. This helps improve output voltage clamping, even when input voltage is high and diode currents are large. An advanced feature of the PolyZen micro-assembly is that the Zener diode is thermally coupled to a resistively nonlinear, polymer PTC (positive temperature coefficient) layer. This PTC layer is fully integrated into the device, and is electrically in series between VIN and the diode clamped VOUT. This advanced PTC layer responds to either extended diode heating or overcurrent events by transitioning from a low to high resistance state, also known as "tripping". A tripped PTC will limit current and generate voltage drop. It helps to protect both the Zener diode and the follow on electronics and effectively increases the diode's power handling capability. The polymer enhanced Zener diode helps protect sensitive portable electronics from damage caused by inductive voltage spikes, voltage transients, incorrect power supplies and reverse bias. These devices are particularly suitable for portable electronics and other low-power DC devices. BENEFITS * Stable Zener diode helps shield downstream electronics from overvoltage and reverse bias * Trip events shut out overvoltage and reverse bias sources * Analog nature of trip events minimizes upstream inductive spikes * Minimal power dissipation requirements * Single component placement FEATURES * Overvoltage transient suppression * Stable VZ vs fault current * Time delayed, overvoltage trip * Time delayed, reverse bias trip * Multi-Watt power handling capability * Integrated device construction * RoHS Compliant TARGET APPLICATIONS * DC power port protection in portable electronics * DC power port protection for systems using barrel jacks for power input * Internal overvoltage & transient suppression * DC output voltage regulation TYPICAL APPLICATION BLOCK DIAGRAM Power Supply PolyZen Protected Electronics (External or Internal) 2 VIN + 1 PolyZen Device GND VOUT 3 Regulated Output RLoad Protected downstream electronics PRODUCT: ZEN132V130A24LS PolyZen 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com Polymer Enhanced Zener Diode Micro-Assemblies DOCUMENT: SCD 26665 REV LETTER: F REV DATE: OCTOBER 29, 2008 PAGE NO.: 2 OF 8 Raychem Circuit Protection Products CONFIGURATION INFORMATION Pin Configuration (Top View) 2 VIN Recommended Pad Dimensions 0.94 mm (0.037") GND 2.21 mm (0.087") 1 3 0.33 mm (0.013") 0.94 mm (0.037") VOUT 0.56 mm (0.022") 2.88 mm (0.1135") 0.56 mm (0.022") PIN DESCRIPTION Pin Number 1 2 3 Pin Name VIN GND VOUT Pin Function VIN. Protected input to Zener diode. GND VOUT. Zener regulated voltage output BLOCK DIAGRAM Polymer PTC VIN VOUT Zener Diode GND DEFINITION of TERMS IPTC IFLT IOUT Trip Event Trip Endurance Current flowing through the PTC portion of the circuit RMS fault current flowing through the diode Current flowing out the VOUT pin of the device A condition where the PTC transitions to a high resistance state, thereby significantly limiting IPTC and related currents, and significantly increasing the voltage drop between VIN and VOUT. Time the PTC portion of the device remains both powered and in a tripped state. IOUT IPTC VIN VOUT IFLT GND PRODUCT: ZEN132V130A24LS PolyZen Polymer Enhanced Zener Diode Micro-Assemblies 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com DOCUMENT: SCD 26665 REV LETTER: F REV DATE: OCTOBER 29, 2008 PAGE NO.: 3 OF 8 Raychem Circuit Protection Products GENERAL SPECIFICATIONS Operating Temperature Storage Temperature -40 to +85C -40 to +85C ELECTRICAL CHARACTERISTICS1-3, 11 (Typical unless otherwise specified) 4 VZ (V) 4 Izt (A) Min Typ Max 13.2 13.4 13.6 0.1 5 I Leakage Current 6 HOLD @ R Typ (Ohms) 20C (A) 1.3 VInt Max (V) Test Voltage Max Current (mA) 13.15 5 0.12 8 IFLT Max Tripped Power 10 Dissipation 9 Max 7 R1Max (Ohms) 0.16 VINT Max (V) 24V Test Current (A) IFLT Max (A) Test Voltage (V) Value (W) Test Voltage (V) 3A +2 -40 +24 -16V 1.0 24 Note 1: Note 2: Electrical characteristics determined at 25C unless otherwise specified. This device is intended for limited fault protection. Repeated trip events or extended trip endurance can degrade the device and may affect performance to specifications. Performance impact will depend on multiple factors including, but not limited to, voltage, trip current, trip duration, trip cycles, and circuit design. For details or ratings specific to your application contact Tyco Electronics Circuit Protection directly. Note 3: Specifications developed using 1.0 ounce 0.045" wide copper traces on dedicated FR4 test boards. Performance in your application may vary. Note 4: Izt is the current at which Vz is measured (VZ = VOUT). Additional VZ values are available on request. Note 5: IHOLD : Maximum steady state IPTC (current entering or exiting the VIN pin of the device) that will not generate a trip event at the specified temperature. Specification assumes IFLT (current flowing through the Zener diode) is sufficiently low so as to prevent the diode from acting as a heat source. Testing is conducted with an "open" Zener. Note 6: R Typ: Resistance between VIN and VOUT pins during normal operation at room temperature. Note 7: R1Max: The maximum resistance between VIN and VOUT pins at room temperature, one hour after 1st trip or after reflow soldering. Note 8: VINT Max: VINT Max relates to the voltage across the PPTC portion of the PolyZen device (VIN-VOUT). VINT Max is defined as the voltage (VIN-VOUT) at which typical qualification devices (98% devices, 95% confidence) survived at least 100 trip cycles and 24 hours trip endurance at the specified voltage (VIN-VOUT) and current (IPTC). VINT Max testing is conducted using a "shorted" load (VOUT = 0V). VINT Max is a survivability rating, not a performance rating. Note 9: IFLT Max: IFLT Max relates to the stead state current flowing through the diode portion of the PolyZen device in a fault condition, prior to a trip event. IFLT Max is defined as the current at which typical qualification devices (12 parts per lot from 3 lots) survived 100 test cycles. RMS fault currents above IFLT Max may permanently damage the diode portion of the PolyZen device. Testing is conducted with NO load connected to VOUT, such that IOUT = 0. "Test voltage" is defined as the voltage between VIN to GND and includes the PolyZen Diode drop. Specification is dependent on the direction of current flow through the diode. IFLT Max is a survivability rating, not a performance rating. Note 10: The power dissipated by the device when in the "tripped" state, as measured on TE test boards (see note 3). Note 11: Specifications based on limited qualification data and subject to change. MECHANICAL DIMENSIONS Length L Width W Height H Length Diode Height Diode Min 3.85 mm (0.152") 3.85 mm (0.152") 1.4mm (0.055") Ld - Hd - Offset O1 - Offset O2 - Typical 4 mm (0.16") 4 mm (0.16") 1.7 mm (0.067") 3.0 mm (0.118") 1.0 mm (0.039") 0.6 mm (0.024") 0.7 mm (0.028") Max 4.15 mm (0.163") 4.15 mm (0.163") 2.0 mm (0.081") - PRODUCT: ZEN132V130A24LS PolyZen 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com Polymer Enhanced Zener Diode Micro-Assemblies Raychem Circuit Protection Products SOLDER REFLOW RECOMMENDATIONS: Classification Reflow Profiles Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Preheat * Temperature Min (Tsmin) * Temperature Max (Tsmax) * Time (tsmin to tsmax) Time maintained above: * Temperature (TL) * Time (tL) Peak/Classification Temperature (Tp) Time within 5 C of actual Peak Temperature (tp) Ramp-Down Rate Time 25 C to Peak Temperature Pb-Free Assembly 3 C/second max. 150 C 200 C 60-180 seconds 217 C 60-150 seconds 260 C 20-40 seconds 6 C/second max. 8 minutes max. DOCUMENT: SCD 26665 REV LETTER: F REV DATE: OCTOBER 29, 2008 PAGE NO.: 4 OF 8 PRODUCT: ZEN132V130A24LS PolyZen Polymer Enhanced Zener Diode Micro-Assemblies 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com DOCUMENT: SCD 26665 REV LETTER: F REV DATE: OCTOBER 29, 2008 PAGE NO.: 5 OF 8 Raychem Circuit Protection Products PACKAGING Packaging ZENXXXVXXXAXXLS Tape & Reel 3,000 Reel Dimensions for PolyZen Devices Amax = 330 Nmin = 102 W1 = 8.4 W2 = 11.1 Matte Finish These Area Nmin Amax Taped Component Dimensions for PolyZen Devices Standard Box 15,000 PRODUCT: ZEN132V130A24LS PolyZen Polymer Enhanced Zener Diode Micro-Assemblies 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com DOCUMENT: SCD 26665 REV LETTER: F REV DATE: OCTOBER 29, 2008 PAGE NO.: 6 OF 8 Raychem Circuit Protection Products TYPICAL CHARACTERISTICS Typical Fault Response: ZEN132V130A24LS 24V, 2.0A Current Limited Source (IOUT = 0) V (V) or I (A) 30 Vin (V) Vout (V) I FLT (A) 25 20 15 10 5 0 0.00 0.10 0.20 0.30 Time (s) 0.40 Pulse IV (300uSec Pulse) Pulse IV (300uSec Pulse) 10 14 13 Current: IFLT (A) Voltage: VOUT (V) 0.50 12 11 ZEN132VxxxAxxLS 5 0 -5 ZEN132VxxxAxxLS 10 1 0.1 0.01 0.001 0.0001 0.00001 -10 -5 Current: IFLT (A) VOUT Peak Vs IFLT RMS (IOUT = 0) Time To Trip (Sec) 17 VOUT Peak (V) 5 10 Voltage: VOUT (V) 15 Time to Trip Vs IFLT RMS (IOUT = 0) 10 18 16 15 14 13 0 ZEN132V130A24LS ZEN132V130A24LS 1 0.1 0.01 12 0 1 IFLT RMS(A) 2 0 1 IFLT RMS (A) 2 PRODUCT: ZEN132V130A24LS PolyZen Polymer Enhanced Zener Diode Micro-Assemblies 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com DOCUMENT: SCD 26665 REV LETTER: F REV DATE: OCTOBER 29, 2008 PAGE NO.: 7 OF 8 Raychem Circuit Protection Products VOUT Peak Vs IFLT RMS (IOUT = 0) Time to Trip Vs IFLT RMS (IOUT = 0) 0 1 ZENxxxV130A24LS ZENxxxV130A24LS Time To Trip (Sec) VOUT (V) -0.2 -0.4 -0.6 -0.8 -1 0.1 0.01 0.001 -1.2 -50 -40 -30 -20 IFLT RMS(A) -10 -50 0 Temperature Effect on IHold (IFLT = 0) Time To Trip (Sec) ZENxxxV130A24LS 1.50 1.00 0.50 0.00 -10 0 ZENxxxV130A24LS 1 0.1 0.01 0.001 -40 -20 0 20 40 60 80 Ambient Temperature (C) Temperature Effect on RTyp 0.40 ZENxxxV130A24LS RTyp (Ohms) IHold (A) -30 -20 IFLT RMS (A) Time to Trip Vs IPTC RMS (IFLT = 0) 10 2.50 2.00 -40 0.30 0.20 0.10 0.00 20 40 60 80 Ambient Temperature (C) 100 0 10 20 30 IPTC RMS (A) 40 PRODUCT: ZEN132V130A24LS PolyZen 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com Polymer Enhanced Zener Diode Micro-Assemblies DOCUMENT: SCD 26665 REV LETTER: F REV DATE: OCTOBER 29, 2008 PAGE NO.: 8 OF 8 Raychem Circuit Protection Products Materials Information ROHS Compliant ELV Compliant Pb-Free Halogen Free* HF * Halogen Free refers to: Br900ppm, Cl900ppm, Br+Cl1500ppm. Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of each product for their applications. Tyco Electronics Corporation assumes no responsibility for the use of its product or for any infringement of patents or other rights of third parties resulting from the use of its product. No license is granted by implication or otherwise under any patent or proprietary right of Tyco Electronics except the right to use such product for the purpose for which it is sold. Tyco Electronics reserves the right to change or update, without notice, any information contained in this publication; to change, without notice, the design, construction, processing, or specification of any product; and to discontinue or limit production or distribution of any product. This publication supersedes and replaces all information previously supplied. Without expressed or written consent by an officer of Tyco Electronics, Tyco Electronics does not authorize the use of any of its products as components in nuclear facility applications, aerospace, or in critical life support devices or systems. Tyco Electronics' only obligations are those in the Tyco Electronics Standard Terms and Conditions of Sale and in no case will Tyco Electronics be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of its products. (c) 2008 Tyco Electronics Corporation. All rights reserved.