UVQ Series www.murata-ps.com Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters PRODUCT OVERVIEW Typical unit FEATURES Standard quarter-brick package/pinout Outputs from 1.5 to 48V up to 125W Low profile 0.42" height 24 and 48Vdc nominal inputs Fully isolated, 2250Vdc (BASIC) insulation For efficient, fully isolated DC power in the smallest space, Murata Power Solutions' UVQ series quarter bricks offer output voltages from 1.5 to 48 Volts with currents up to 40 Amps. UVQs operate over a wide temperature range (up to +70C at 200 lfm airflow) at full-rated power. The optional mounting baseplate extends this to all practical temperature ranges at full power. UVQs achieve these impressive specifications while delivering excellent electrical performance. Overall noise is 35mVp-p (3.3V models) with fast step response (down to 50sec). These converters offer high stability even with no load and tight output regulation. The unit is fully protected against input over and undervoltage, output overcurrent and short circuit. An on-board temperature sensor shuts down the converter if thermal limits are reached. Protection uses the "hiccup" (auto restart) method. A convenient remote On/Off control input operates by external digital logic, relay or transistor input. To compensate for longer wiring and to retain output voltage accuracy at the load, UVQs include a Sense input to dynamically correct for ohmic losses. A trim input may be connected to a user's adjustment potentiometer or trim resistors for output voltage calibration closer than the standard accuracy. UVQs include industry-standard safety certifications and BASIC I/O insulation provides 2250 Volt input/output isolation. Radiation emission testing is performed to widely-accepted EMC standards. The UVQs may be considered as higher performance replacements for some Murata Power Solutions USQ models. Designed for RoHS-6 compliance Output overvoltage/short-circuit protected On/Off control, trim and sense functions High efficiency to 92% Protected against temp. and voltage limits Designed to meet UL/IEC/EN60950-1 safety approvals +SENSE (7) +VOUT (8) +VIN (1) Baseplate (9) Optional SWITCH CONTROL -VOUT (4) -VIN (3) -SENSE (5) PWM CONTROLLER INPUT UNDERVOLTAGE, INPUT OVERVOLTAGE, AND OUTPUT OVERVOLTAGE COMPARATORS REMOTE ON/OFF CONTROL* (2) For full details go to www.murata-ps.com/rohs OPTO ISOLATION REFERENCE & ERROR AMP VOUT TRIM (6) * Can be ordered with positive (standard) or negative (optional) polarity. Typical configuration -- some models use a different topology Figure 1. Simplified Schematic www.murata-ps.com/support MDC_UVQ Models.F02 Page 1 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE Output Root Models UVQ-1.5/40-D24P-C UVQ-2.5/35-D24P-C UVQ-2.5/40-D48N-C UVQ-3.3/30-D24P-C UVQ-3.3/35-D48N-C UVQ-5/20-D24P-C UVQ-5/20-D48N-C UVQ-12/8-D24P-C UVQ-12/10-D48N-C UVQ-15/7-D24P-C UVQ-15/7-D48N-C UVQ-18/5.6-D24P-C UVQ-18/6-D48N-C UVQ-24/4.5-D24P-C UVQ-24/4.5-D48N-C UVQ-48/2.5-D24P-C UVQ-48/2.5-D48N-C Input R/N (mVp-p) Regulation (Max.) VOUT IOUT Power VIN Nom. Range IIN, No Load IIN, Full Load (Volts) (Amps) (Watts) Typ. Max. Line Load (Volts) (Volts) (mA) (Amps) 1.5 40 35 40 30 35 60 87.5 100 99 115.5 5 20 100 12 8 10 96 120 15 7 105 18 5.6 6 100.8 24 4.5 48 2.5 2.5 3.3 108 120 30 35 30 20 95 110 85 120 125 125 60 75 100 250 60 60 60 65 40 50 25 130 160 150 150 185 185 100 130 200 375 0.075% 0.05% 0.05% 0.1% 0.05% 0.05% 0.05% 0.1% 0.075% 0.05% 0.05% 0.05% 0.05% 0.075% 0.075% 0.1% 0.175% These are partial model numbers. Please refer to the full model number structure for complete ordering part numbers. Min. IOUT = 3 Amps for UVQ-3.3 Vout models. All specifications are at nominal line voltage and full load, +25C unless otherwise noted. See detailed specifications. 0.05% 0.05% 0.05% 0.25% 0.25% 0.05% 0.05% 0.1% 0.05% 0.05% 0.02% 0.075% 0.075% 0.15% 0.25% 0.2% 0.2% 24 24 48 24 48 24 48 24 48 24 48 24 48 24 48 24 48 18-36 18-36 36-75 18-36 36-75 18-36 36-75 18-36 36-75 18-36 36-75 18-36 36-75 18-36 36-75 18-36 36-75 80 100 100 180 130 190 80 90 60 103 60 140 80 45 45 45 30 2.84 4.14 2.37 4.58 2.7 4.53 2.31 4.4 2.78 4.85 2.39 4.69 2.5 5.03 2.49 4.4 2.71 Efficiency) Min. 86.5% 86% 87% 88.5% 87% 91% 88.5% 89% 88.5% 88.5% 90% 88% 88.3% 88% 89% 89% 91% Typ. Package (Case, Pinout) 88% 88% 88% 90% 89% 92% 90% 91% 90% C59, P32 90.3% 91.5% 89.5% 90% 89.5% 90.5% 91% 92.3% Output capacitors are 1uF ceramic || 10 uF electrolytic. Input cap is 22 uF, low ESR, except UVQ-24/4.5 is 33uF and UVQ-48/2.5 uses no input cap. I/O caps are necessary for our test equipment and may not be needed for your application. IOUT = 14 Amps max. with VIN = 18-19.5 Volts. Model UVQ-31128-C is a standard model UVQ-5/20-D48NB-C with modified rise time to reach 4.75V within 10 mSec. All other specifications are as per the standard product. UVQ Pin 9 Baseplate Connection The UVQ series may include an optional installed baseplate for extended thermal management. Various UVQ models (see list below) are also available with an additional pin 9 on special order which connects to the baseplate but is electrically isolated from the rest of the converter. Please refer to the mechanical drawings. Pin 9 offers a positive method of controlling the electrical potential of the baseplate, independent of the converter. Some baseplate models cannot include pin 9 and in such cases, the baseplate is grounded by the mounting bolts. Or consider adding an external lugged washer with a grounding terminal. The baseplate may be ordered by adding a "B" to the model number tree and pin 9 will be pre-installed by adding a "9". The two options are separate. Please refer to the Ordering Guide. Do not order pin 9 without the baseplate. Note that "pin 9" converters may be on limited forecast, requiring minimum order quantities and scheduled deliveries. Models available with Pin 9: UVQ-12/10-D48 UVQ-1.5/40-D24 Models which are NOT available with Pin 9: UVQ-5/20-D24 and -D48 UVQ-3.3/30-D24 UVQ-3.3/35-D48 UVQ-2.5/35-D24 UVQ-2.5/40-D48 Other models which are not listed will be reviewed for future pin 9 accomodation. www.murata-ps.com/support MDC_UVQ Models.F02 Page 2 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters PART NUMBER STRUCTURE U VQ - 3.3 / 20 - D48 N B 9 LX - C RoHS-6 hazardous substance compliant (does not claim EU RoHS exemption 7b-lead in solder) Output Configuration U = Unipolar/Single Alternate Pin Length: (special quantity order) Blank = Standard pin length L1 = 0.110 (2.79mm) L2 = 0.145 (3.68mm) Quarter-Brick Package Nominal Output Voltage Baseplate Pin 9, see Mechanical Drawings: (special order) 1.2 to 48 Volts Blank = No pin 9, standard 9 = Pin 9 installed (see description on pg. 2), optional Maximum Rated Output Current in Amps Blank = No baseplate, standard B = Baseplate installed, optional special order Input Voltage Range: D24 = 18-36 Volts (24V nominal) D48 = 36-75 Volts (48V nominal) * Note: Remote On/Off Control Logic: Some model number combinations may not be Add "P" for positive logic available. Contact Murata Power Solutions. Add "N" for negative logic Positive "P" logic is standard for D24 models and optional special order for D48 models. Negative "N" logic is standard for D48 models and optional special order for D24 models. ORDERING GUIDE SUMMARY Model VOUT Range All Models 1.2V to 48V IOUT Range 2.5A to 40A INPUT CHARACTERISTICS Parameter Typ. @ 25C, full load Notes Voltage Range Current, full power Isolation Remote On/Off Control 18-36 or 36-75 Volts Up to 5.6 Amps 2kVdc to 2250V Switch or FET control 24V or 48V nominal Model dependent Model dependent Positive or negative logic OUTPUT CHARACTERISTICS Parameter Voltage Current Accuracy Ripple & Noise (to 20MHz) Line and Load Regulation Overcurrent Protection Overtemperature Protection Efficiency (minimum) Typ. @ 25C, full load 1.5 to 48 Volts 10% 2.5 to 40 Amps fullscale Down to 1% of VNOM Down to 35mVp-p Down to 0.125%/0.25% 150% of IOUT max. +125C See Performance Specifications Notes Trimmable No minimum load Most models Model dependent Model dependent With hiccup auto-restart GENERAL SPECIFICATIONS Parameter Typ. @ 25C, full load Notes Dynamic Load Response Operating Temperature Range Safety Down to 50sec -40 to +110C UL/IEC/EN 60950-1 Model dependent With baseplate, see derating curve and CSA C22.2-No.234 VIN Range 18-36V or 36-75V Efficiency Up to 92.%, model dependent MECHANICAL CHARACTERISTICS With baseplate 1.45 x 2.30 x 0.5 inches (36.83 x 58.42 x 12.7 mm) Without baseplate 1.45 x 2.30 x 0.42 inches (36.83 x 58.42 x 10.67 mm) See Performance Specifications, page 2 www.murata-ps.com/support MDC_UVQ Models.F02 Page 3 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Performance/Functional Specifications 24V Models UVQ-48/2.5-D24 17 UVQ-24/4.5-D24 UVQ-5/20-D24 17 UVQ-18/5.6-D24 UVQ-3.3/30-D24 17 UVQ-15/7-D24 UVQ-2.5/35-D24 17 17 17 17 17 17 16.25 16 16.25 16 16 UVQ-12/8-D24 UVQ-1.5/40-D24 Typical @ TA = +25C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1) Input Input voltage range Start-up threshold, (V) min. See ordering guide Undervoltage shutdown, (V)14 16 Overvoltage shutdown (V) none 39 Reflected (back) ripple current2 none 10-50 mA pk-pk, model dependent Input Current Full load conditions 2 See ordering guide. Inrush transient, (A sec) 0.5 Output short circuit, (mA) 40 No load, mA 80 100 180 3.79 5.49 6.04 Low line (VIN = min.), (Amps) 0.5 0.05 0.5 Standby mode, (Off, UV, OT shutdown) Internal input filter type Reverse polarity protection 0.1 1 1 0.05 0.05 10 320 50 50 50 190 90 103 140 45 30 5.57 5.93 6.52 6.29 6.67 3.60 50 1-4mA, model dependent L-C Pi-type L-C See notes. Remote On/Off Control5 Positive logic, "P" suffix (specifications are max) OFF = Ground pin to +0.8V ON = Open or +5V to +VIN max. Negative logic, "N" suffix (specifications are max) OFF = Open or +5V to +VIN max ON = Ground pin to+0.8V max Current 1-8 mA, model dependent www.murata-ps.com/support MDC_UVQ Models.F02 Page 4 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Performance/Functional Specifications 24V Models UVQ-48/2.5-D24 UVQ-24/4.5-D24 UVQ-18/5.6-D24 UVQ-15/7-D24 UVQ-12/8-D24 UVQ-5/20-D24 UVQ-3.3/30-D24 UVQ-2.5/35-D24 UVQ-1.5/40-D24 Typical @ TA = +25C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1) Output Voltage output range See ordering guide. Voltage output accuracy (50% load) 1.5% of VNOM 1.25% of VNOM Adjustment range -20 to +10% of VNOM. Temperature coefficient Minimum loading 3 amps No minimum load +10%. Ripple/noise See ordering guide. Line/Load regulation See ordering guide. Efficiency See ordering guide. Maximum capacitive loading, Low ESR <0.02 max., resistive load, (F) 10,000 45 5000 44 36 Short circuit protection method Short circuit current, (Amps) 4700 24 10 9.5 2200 7.2 5.8 3.4 5 2.8 Current limiting, hiccup autorestart. Remove overload for recovery. 3.6 3 3 Short circuit duration Overvoltage protection, (via magnetic feedback) 10% of VNOM. 0.02% of VOUT range per C No minimum load Remote sense compensation Current limit inception (98% of VOUT, after warmup), (Amps) 1% of VNOM 3 1.5 15 mA 3 Output may be shorted continuously to ground (no damage). 2.3 Volts 3 Volts max 4 Volts max 6.8 Volts max 14.4 Volts max 18.5 Volts 22 Volts max 29 Volts max 59 Volts max Isolation Characteristics Isolation Voltage Input to Output, (Volts min) 2000 Input to baseplate 1500 Baseplate to output, (Volts min) 1500 1000 Isolation resistance Isolation capacitance, (pF) Isolation safety rating 1500 100 M 1500 1000 2000 50 Basic insulation www.murata-ps.com/support MDC_UVQ Models.F02 Page 5 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Performance/Functional Specifications 24V Models UVQ-48/2.5-D24 UVQ-24/4.5-D24 UVQ-18/5.6-D24 UVQ-15/7-D24 UVQ-12/8-D24 UVQ-5/20-D24 UVQ-3.3/30-D24 UVQ-2.5/35-D24 UVQ-1.5/40-D24 Typical @ TA = +25C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1) Dynamic characteristics Dynamic load response (50-75-50% load step) Start-up time VIN to VOUT regulated, mSec Remote On/Off to VOUT regulated, mSec Switching frequency, (KHz) 100 Sec to 1% of final value 150 Sec to 150 Sec to 100 Sec to 50 Sec 40 Sec to 50 Sec to 100 Sec 100 Sec 1.5% 1.5% 1.5% of final to 1% 1.25% 1% to 1% to 1% of final value of final value value of final value of final value of final value of final value of final value 90msec 50msec 50msec 200msec 40msec 30msec 30msec 290msec 100msec 90msec 50msec 50msec 200msec 30msec 25msec 35msec 200msec 100msec 380 30 500 to 650 600 360 290 30 242 240 25 290 30 250 25 Environmental Calculated MTBF4 TBD Operating temperature range: see Derating Curves. -40 to +85C (with Derating, see Note 15.) Operating temperature, with baseplate, no derating required (C)3 -40 to +110 Storage temperature (C) -40 to +115 -40 to +110 -55 to +130 Thermal protection/ shutdown +110 to 125C, model dependent Relative humidity To +85C/85%, non-condensing -55 to +125 Physical Outline dimensions See mechanical specs. Baseplate material Aluminum Pin material Copper alloy Pin diameter Weight 0.040/0.062 inches (1.016/1.575 mm) 1.55 ounce (44 grams) Electromagnetic interference (conducted and radiated) (external filter required) Safety 1 ounce (28 grams) Designed to meet FCC part 15, class B, EN55022 Designed to meet UL/cUL 60950-1, CSA C22.2 No.60950-1, IEC/EN 60950-1 www.murata-ps.com/support MDC_UVQ Models.F02 Page 6 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Performance/Functional Specifications 48V Models UVQ-48/2.5-D48 UVQ-24/4.5-D48 UVQ-18/6-D48 UVQ-15/7-D48 UVQ-12/10-D48 UVQ-5/20-D48 UVQ-3.3/35-D48 UVQ-2.5/40-D48 Typical @ TA = +25C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1) Input Input voltage range See ordering guide Start-up threshold, min (V) 35 Undervoltage shutdown, (V)14 34.5 34 33.5 34.5 35 32 Overvoltage shutdown (V) 33.5 none Reflected (back) ripple current 10-50 mA pk-pk, model dependent Input Current Full load conditions 2 Inrush transient, (A sec) See ordering guide. 0.05 Output short circuit, (mA) 0.05 1 50 1 0.05 1 0.05 0.05 10 30 50 250 50 No load, mA 100 130 80 60 30 80 45 30 Low line (VIN = min.), (Amps) 3.15 3.56 3.07 3.72 3.21 3.35 3.30 3.60 Standby mode, (Off, UV, OT shutdown) Internal input filter type Reverse polarity protection 1-4mA, model dependent L-C Pi-type L-C See notes. Remote On/Off Control5 Positive logic, "P" suffix (specifications are max) OFF = Ground pin to +0.8V ON = Open or +5V to +VIN max Negative logic, "N" suffix (specifications are max) OFF = Open or +5V to +VIN max ON = Ground pin to+0.8V max Current 1-8 mA, model dependent www.murata-ps.com/support MDC_UVQ Models.F02 Page 7 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Performance/Functional Specifications 48V Models UVQ-48/2.5-D48 UVQ-24/4.5-D48 UVQ-18/6-D48 UVQ-15/7-D48 UVQ-12/10-D48 UVQ-5/20-D48 UVQ-3.3/35-D48 UVQ-2.5/40-D48 Typical @ TA = +25C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1) Output Voltage output range See ordering guide. Voltage output accuracy (50% load) 1.5% of VNOM 1.25% of VNOM Adjustment range -20 to +10% of VNOM. Temperature coefficient Minimum loading 1% of VNOM +10% of VNOM. 0.02% of VOUT range per C No minimum load 3 Amps No minimum load No minimum load Remote sense compensation +10%. Ripple/noise See ordering guide. Line/Load regulation See ordering guide. Efficiency See ordering guide. Maximum capacitive loading, Low ESR <0.02 max., resistive load, (F) Current limit inception (98% of VOUT, after warmup), (Amps) 10,000 46 4700 48 Short circuit protection method 26 8.5 7 1000 6.5 3.3 3 3.5 29 Volts max 55 Volts max Current limiting, hiccup autorestart. Remove overload for recovery. Short circuit current, (Amps) 5 0.1 Short circuit duration Overvoltage protection, (via magnetic feedback) 12.5 2200 1.5 3 3 Output may be shorted continuously to ground (no damage). 3 Volts max 4 Volts max 6 Volts max 14.4 Volts max 18.5 Volts max 22 Volts max Isolation Characteristics Isolation Voltage Input to Output, (Volts min) 2250 Input to baseplate 1500 Baseplate to output, (Volts min) 1500 1500 Isolation resistance Isolation capacitance, (pF) Isolation safety rating 100 M 1500 1000 50 50 1500 Basic insulation www.murata-ps.com/support MDC_UVQ Models.F02 Page 8 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Performance/Functional Specifications 48V Models 50msec 50msec 50msec 50msec 30msec 30msec 30msec 100msec 50msec 600 600 450 50 290 30 245 20 240 25 290 30 540 40 -40 to +110 -40 to +120 UVQ-15/7-D48 UVQ-48/2.5-D48 50msec UVQ-5/20-D48 UVQ-24/4.5-D48 150 Sec to 1.5% of final value UVQ-18/6-D48 UVQ-3.3/35-D48 150 Sec to 1.5% of final value UVQ-12/10-D48 UVQ-2.5/40-D48 Typical @ TA = +25C under nominal line voltage, nominal output voltage, natural air convection, external caps and full-load conditions, unless noted. (1) Dynamic characteristics Dynamic load response (50-75-50% load step) Start-up time VIN to VOUT regulated, mSec Remote On/Off to VOUT regulated, mSec Switching frequency, (KHz) 90 Sec 100 Sec 50 Sec to 1% 50 Sec to 1% 50 Sec to 1% to 2% to 1% of final value of final value of final value of final value of final value 50msec 40msec 30msec 30msec 100msec 75 Sec to 1% of final value 50msec Environmental Calculated MTBF4 TBD Operating temperature range: see Derating Curves. Operating temperature, with baseplate, no derating required (C)3 Storage temperature (C) -40 to +85C (with Derating, see Note 15.) -40 to +110 -40 to +115 -40 to +110 -55 to +125 Thermal protection/ shutdown +110 to 125C, model dependent Relative humidity To +85C/85%, non-condensing Physical Outline dimensions Baseplate material See mechanical specs. Aluminum Pin material Copper alloy Pin diameter 0.040/0.062 inches (1.016/1.575 mm) Weight Electromagnetic interference (conducted and radiated) (external filter required) Safety 1 ounce (28 grams) Designed to meet FCC part 15, class B, EN55022 Designed to meet UL/cUL 60950-1, CSA C22.2 No.60950-1, IEC/EN 60950-1 www.murata-ps.com/support MDC_UVQ Models.F02 Page 9 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters TYPICAL PERFORMANCE DATA UVQ-1.5/40-D24N: Maximum Current Temperature Derating (No baseplate, V IN = 24V, transverse air flow) UVQ-1.5/40-D24N: Maximum Current Temperature Derating (With baseplate, V IN = 24V, transverse air flow) 40 40 39 Output Current (Amps) Output Current (Amps) 39 Natural convection 38 100 lfm 37 200 lfm 200 lfm 36 400 lfm 35 34 Natural convection 38 37 100 lfm 36 400 lfm 35 34 33 33 20 25 30 35 40 45 50 55 60 65 70 75 80 85 20 25 30 35 40 Ambient Temperature ( oC) 50 55 60 65 70 75 80 85 UVQ-2.5/40-D48 Power Dissipation vs. Load Current @ 25C UVQ-2.5/40-D48N Efficiency vs. Line Voltage and Load Current @ 25C 16 92 14 Power Dissipation (Watts) 88 84 80 Efficiency (%) 45 Ambient Temperature ( oC) 76 VIN = 36V 72 VIN = 48V 68 12 VIN = 48V 10 8 6 4 VIN = 75V 2 64 0 62 0 5 10 15 20 25 30 35 0 40 5 10 15 20 25 30 35 40 Load Current (Amps) Load Current (Amps) UVQ-3.3/30-D24N: Maximum Current Temperature Derating (No baseplate, V IN = 24V, transverse air flow at sea level) UVQ-3.3/30-D24N: Maximum Current Temperature Derating (With baseplate, V IN = 24V, transverse air flow at sea level) 30 30 29 29 27 Output Current (Amps) Output Current (Amps) 28 Natural convection 26 25 100 lfm 24 200 lfm 23 300 lfm 22 21 28 Natural convection 27 100 lfm 26 200 lfm 25 300 lfm 24 400 lfm 400 lfm 20 23 19 22 18 17 21 20 25 30 35 40 45 50 55 60 Ambient Temperature ( oC) 65 70 75 80 85 20 25 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature ( oC) www.murata-ps.com/support MDC_UVQ Models.F02 Page 10 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters TYPICAL PERFORMANCE DATA Output Current (Amps) UVQ-3.3/35-D48 Maximum Current Temperature Derating (With baseplate, V IN = 48V, transverse air flow at sea level) UVQ-5/20-D24P Efficiency vs. Line Voltage and Load Current @ +25C 36 94 34 93 32 92 30 91 Natural Convection 26 VIN = 18V Efficiency (%) 28 100 lfm 24 200 lfm 90 22 300 lfm 20 25 30 35 40 45 50 88 VIN = 30V 87 VIN = 36V 86 400 lfm 18 20 VIN = 24V 89 55 60 65 70 75 80 85 85 Ambient Temperature ( oC) 84 5 6.5 8 9.5 11 12.5 14 15.5 17 18.5 20 80 85 Load Current (Amps) UVQ-5/20-D24 Power Dissipation vs. Load Current @ +25C 10 Power Dissipation (Watts) 9 8 7 6 5 4 VIN = 18V VIN = 24V 3 VIN = 30V 2 VIN = 36V 1 5 6.5 8 9.5 11 12.5 14 15.5 17 18.5 20 Load Current (Amps) UVQ-5/20-D24P: Maximum Current Temperature Derating (No baseplate, VIN = 24V, transverse air flow) UVQ-5/20-D24PB: Maximum Current Temperature Derating (With baseplate, VIN = 24V, transverse air flow) 20 20 19.5 19.5 Output Current (Amps) Output Current (Amps) 19 18.5 18 17.5 17 Natural convection 100 lfm 200 lfm 300 lfm 400 lfm 16.5 16 15.5 19 18.5 Natural convection 100 lfm 200 lfm 300 lfm 400 lfm 18 17.5 17 16.5 15 16 14.5 14 15.5 20 25 30 35 40 45 50 55 60 65 Ambient Temperature (oC) 70 75 80 85 20 25 30 35 40 45 50 55 60 65 70 75 Ambient Temperature (oC) www.murata-ps.com/support MDC_UVQ Models.F02 Page 11 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters TYPICAL PERFORMANCE DATA UVQ-5/20-D48P: Maximum Current Temperature Derating (No baseplate, V IN = 48V, transverse air flow at sea level) UVQ-5/20-D48 Efficiency vs. Line Voltage and Load Current @ 25C 21 92 20 Output Current (Amps) 88 Efficiency (%) 84 80 76 VIN = 36V 19 18 100 lfm 17 200 lfm 16 300 lfm 15 400 lfm 72 14 VIN = 48V Natural convection 13 68 VIN = 75V 12 64 20 25 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature ( oC) 62 0 2 4 6 8 10 12 14 16 18 20 Load Current (Amps) UVQ-5/20-D48PB: Maximum Current Temperature Derating (With baseplate, V IN = 48V, transverse air flow at sea level) UVQ-12/8-D24P Efficiency vs. Line Voltage and Load Current @ +25C 21 95 19 90 18 100 lfm 17 200 lfm 16 300 lfm 15 VIN = 18V Efficiency (%) Output Current (Amps) 20 400 lfm 85 VIN = 24V VIN = 30V 80 VIN = 36V 14 75 13 20 25 30 35 40 45 50 55 60 65 70 75 80 85 0.8 1.6 2.4 UVQ-12/8-D24P: Maximum Current Temperature Derating (No baseplate, VIN = 24V, transverse air flow) 4 4.8 8.0 92 7.8 90 7.6 88 VIN = 36V 86 VIN = 48V 84 VIN = 60V 7.4 100 lfm 200 lfm 300 lfm 7.2 7.0 6.8 25 30 35 40 45 50 55 60 65 Ambient Temperature (oC) 6.4 7.2 8 VIN = 75V 82 20 5.6 UVQ-12/10-D48N Efficiency vs. Line Voltage and Load Current @ +25C Efficiency (%) Output Current (Amps) 3.2 Load Current (Amps) Ambient Temperature ( oC) 70 75 80 85 90 80 78 1 2 3 4 5 6 7 8 9 10 Load Current (Amps) www.murata-ps.com/support MDC_UVQ Models.F02 Page 12 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters TYPICAL PERFORMANCE DATA UVQ-12/10-D48N: Maximum Current Temperature Derating (No baseplate, VIN = 48V, transverse air flow) UVQ-12/10-D48N Power Dissipation vs. Load Current @ +25C 10 13 11 VIN = 75V 9 VIN = 60V VIN = 48V 7 9 Output Current (Amps) Power Dissipation (Watts) 15 VIN = 36V 5 8 7 Natural convection 100 lfm 200 lfm 300 lfm 400 lfm 6 3 1 1 2 3 4 5 6 7 8 9 5 10 20 Load Current (Amps) 25 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (oC) UVQ-15/7-D24N Efficiency vs. Line Voltage and Load Current @ +25C 10.0 94 9.5 92 9.0 90 Efficiency (%) Output Current (Amps) UVQ-12/10-D48N: Maximum Current Temperature Derating (With baseplate, VIN = 48V, transverse air flow) 8.5 8.0 7.5 Natural convection 100 lfm 200 lfm 300 lfm 400 lfm 7.0 6.5 88 VIN = 18V 86 VIN = 24V VIN = 30V 84 VIN = 36V 82 80 6.0 20 25 30 35 40 45 50 55 60 65 70 75 80 0.7 85 1.4 2.1 2.8 3.5 4.2 4.9 5.6 6.3 7 Load Current (Amps) Ambient Temperature (oC) UVQ-15/7-D24N: Maximum Current Temperature Derating (No baseplate, VIN = 24V, transverse air flow) UVQ-15/7-D24N Power Dissipation vs. Load Current @ +25C 7.5 13 Output Current (Amps) Power Dissipation (Watts) 7 11 9 VIN = 36V VIN = 30V 7 VIN = 24V VIN = 18V 5 3 6.5 6 5.5 Natural convection 100 lfm 200 lfm 300 lfm 400 lfm 5 4.5 1 4 0.7 1.4 2.1 2.8 3.5 4.2 4.9 Load Current (Amps) 5.6 6.3 7 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 Ambient Temperature (oC) www.murata-ps.com/support MDC_UVQ Models.F02 Page 13 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters TYPICAL PERFORMANCE DATA UVQ-15/7-D24N: Maximum Current Temperature Derating (With baseplate, VIN = 24V, transverse air flow) UVQ-15/7-D48N Efficiency vs. Line Voltage and Load Current @ +25C 7.5 94 92 90 Efficiency (%) Output Current (Amps) 7 6.5 6 Natural convection 100 lfm 200 lfm 300 lfm 400 lfm 5.5 5 88 86 VIN = 36V 84 VIN = 48V 82 VIN = 60V 80 VIN = 75V 78 4.5 76 0.7 4 20 25 30 35 40 45 50 55 60 65 70 75 80 85 1.4 2.1 2.8 3.5 4.2 4.9 5.6 6.3 7 Load Current (Amps) 90 Ambient Temperature (oC) UVQ-15/7-D48N: Maximum Current Temperature Derating (No baseplate, VIN = 48V, transverse air flow) UVQ-15/7-D48N Power Dissipation vs. Load Current @ +25C 11 9 8 VIN = 75V 7 VIN = 60V VIN = 48V VIN = 36V 6 Output Current (Amps) Power Dissipation (Watts) 10 5 4 3 2 1 0.7 1.4 2.1 2.8 3.5 4.2 4.9 Load Current (Amps) 5.6 6.3 7 7.0 6.8 6.6 6.4 6.2 6.0 5.8 5.6 5.4 5.2 5.0 4.8 4.6 4.4 4.2 4.0 Natural convection 100 lfm 200 lfm 300 lfm 400 lfm 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 Ambient Temperature (oC) UVQ-18/5.6-D24 Efficiency vs. Line Voltage and Load Current @ 25C 92 7.0 6.8 6.6 6.4 6.2 6.0 5.8 5.6 5.4 5.2 5.0 4.8 4.6 4.4 4.2 4.0 90 88 Efficiency (%) Output Current (Amps) UVQ-15/7-D48N: Maximum Current Temperature Derating (With baseplate, VIN = 48V, transverse air flow) Natural convection 100 lfm 200 lfm 300 lfm 86 84 VIN = 18V 82 VIN = 24V 80 VIN = 36V 78 76 0.56 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 1.12 1.68 2.24 2.8 3.36 3.92 4.48 5.04 5.6 Load Current (Amps) Ambient Temperature (oC) www.murata-ps.com/support MDC_UVQ Models.F02 Page 14 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters TYPICAL PERFORMANCE DATA UVQ-18/5.6-D24: Maximum Current Temperature Derating (No baseplate, V IN = 24V, transverse air flow) UVQ-18/5.6-D24: Maximum Current Temperature Derating (With baseplate, V IN = 24V, transverse air flow) 5.8 5.8 5.6 5.6 200 lfm 5.2 Output Current (Amps) Output Current (Amps) 5.4 300 lfm 5 4.8 400 lfm 100 lfm 4.6 4.4 4.2 4 Natural Convection 3.8 5.4 5.2 5 Natural Convection 4.8 100 lfm 200 lfm 4.6 300 lfm 400 lfm 4.4 4.2 3.6 4 3.4 20 25 30 35 40 45 50 55 60 65 70 75 80 20 85 25 30 35 40 Ambient Temperature ( oC) 45 50 55 60 65 70 75 80 85 Ambient Temperature ( oC) UVQ-18/6-D48 Power Dissipation vs. Load Current @ 25C UVQ-18/6-D48N Efficiency vs. Line Voltage and Load Current @ 25C 16 95 14 90 VIN = 75V Power Dissipation (Watts) Efficiency (%) 85 80 VIN = 36V 75 VIN = 48V 70 12 VIN = 48V 10 VIN = 36V 8 6 4 VIN = 75V 65 2 0 0.6 60 0.6 1.2 1.8 2.4 3 3.6 4.2 4.8 5.4 6 1.2 1.8 2.4 3.6 4.2 4.8 5.4 6 UVQ-18/6-D48: Maximum Current Temperature Derating (With baseplate, V IN = 48V, transverse air flow) 6.5 6.5 6 6 Output Current (Amps) Output Current (Amps) UVQ-18/6-D48: Maximum Current Temperature Derating (No baseplate, V IN = 48V, transverse air flow) 5.5 5 100 lfm 200 lfm 4.5 3 Load Current (Amps) Load Current (Amps) 5.5 100 lfm 5 200 lfm 4.5 300 lfm 300 lfm 500 lfm 4 4 500 lfm 3.5 3.5 20 25 30 35 40 45 50 55 60 Ambient Temperature (oC) 65 70 75 80 85 20 25 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature (oC) www.murata-ps.com/support MDC_UVQ Models.F02 Page 15 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters TYPICAL PERFORMANCE DATA UVQ-24/4.5-D24N Efficiency vs. Line Voltage and Load Current @ +25C 91 90 89 Efficiency (%) 88 87 86 VIN = 18V 85 VIN = 24V 84 VIN = 30V 83 VIN = 36V 82 81 80 1.00 1.35 1.70 2.05 2.40 2.75 3.10 3.45 3.80 4.15 4.50 Load Current (Amps) UVQ-24/4.5-D24P: Maximum Current Temperature Derating (With baseplate, Vin= 24V, air flow is from Pin 1 to Pin 3) 4.50 4.50 4.25 4.25 Output Current (Amps) Output Current (Amps) UVQ-24/4.5-D24P: Maximum Current Temperature Derating (No baseplate, Vin= 24V, air flow is from Pin 1 to Pin 3) 4.00 3.75 400 LFM 300 LFM 200 LFM 100 LFM LOW LFM 3.50 3.25 4.00 3.50 3.25 3.00 3.00 2.75 2.75 2.50 400 LFM 300 LFM 200 LFM 100 LFM LOW LFM 3.75 2.50 20 25 30 35 40 45 50 55 60 65 70 75 80 85 20 25 30 35 40 Ambient Temperature (oC) 55 60 65 70 75 80 85 85 90 UVQ-24/4.5-D48N: Maximum Current Temperature Derating (No baseplate, VIN = 48V, transverse air flow) 4.5 Output Current (Amps) Efficiency (%) 50 Ambient Temperature (oC) UVQ-24/4.5-D48N Efficiency vs. Line Voltage and Load Current @ +25C 92 90 88 86 84 82 80 78 76 74 72 70 68 66 64 1.00 45 VIN = 36V VIN = 48V VIN = 60V VIN = 75V 4.3 400 lfm 300 lfm 200 lfm 100 lfm 4.0 3.8 3.5 3.3 3.0 1.35 1.70 2.05 2.40 2.75 3.10 Load Current (Amps) 3.45 3.80 4.15 4.50 20 25 30 35 40 45 50 55 60 65 70 75 80 Ambient Temperature (oC) www.murata-ps.com/support MDC_UVQ Models.F02 Page 16 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters TYPICAL PERFORMANCE DATA UVQ-48/2.5-D48N: Maximum Current Temperature Derating (With baseplate, V IN = 48V, transverse air flow) UVQ-48/2.5-D48N Efficiency vs. Line Voltage and Load Current @ 25C 2.6 93 2.5 Output Current (Amps) 92 Efficiency (%) 91 90 VIN = 36V 89 2.4 Natural convection 2.3 100 lfm 2.2 200 lfm VIN = 48V 88 2.1 VIN = 60V 87 2.0 20 VIN = 75V 86 85 0.25 25 30 35 40 45 50 55 60 65 70 75 80 85 Ambient Temperature ( oC) 0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.5 Load Current (Amps) www.murata-ps.com/support MDC_UVQ Models.F02 Page 17 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters MECHANICAL SPECIFICATIONS Case C59 with Baseplate 2.30 (58.4) 1.860 (47.2) A B A B Case C59 0.42 (10.7) PINS 1-3, 5-7: 0.040 0.002 (1.016 0.05) PINS 4 & 8: 0.062 0.002 (1.575 0.05) 2.00 (50.8) 1.45 (36.8) 1.030 (26.2) 0.188 (4.78) B B A 4 5 6 7 3 2 0.600 (15.24) 4 EQ. SP. @ 0.150 (3.81) 8 1 BASEPLATE #M3-THREAD X 0.15 DEEP TYPICAL (4) PLACES 1.45 (36.8) 0.50 (12.7) PINS 1-3, 5-7: 0.040 0.002 (1.016 0.05) PINS 4 & 8: 0.062 0.002 (1.575 0.05) BOTTOM VIEW 0.188 (4.8) Alternate pin lengths are available. Contact Murata Power Solutions. 2.30 (58.4) A 2.00 (50.8) A B Optional baseplate pin is special order. Contact Murata Power Solutions.. 0.15 (3.81) 3 9 2 Optional pin 9 connects to baseplate. Electrically isolated from converter. 4 5 6 7 0.600 (15.24) 4 EQ. SP. @ 0.150 (3.81) 8 1 BOTTOM VIEW Dimensions are in inches (mm shown for ref. only). Third Angle Projection Tolerances (unless otherwise specified): .XX 0.02 (0.5) .XXX 0.010 (0.25) Angles 2 Components are shown for reference only. DOSA-Compliant I/O Connections Pin Function P32 1 +Vin 2 On/Off Control 3 -Vin 4 -Vout 5 -Sense 6 Trim 7 +Sense 8 +Vout Important: If sense inputs are not connected to a remote load, connect them to their respective VOUT pins at the converter. www.murata-ps.com/support MDC_UVQ Models.F02 Page 18 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters ABSOLUTE MAXIMUM RATINGS TECHNICAL NOTES Input Voltage Continuous Transient (100 mS) 24V models 0 to +36V +50V 48V models 0 to +75V +100V On/Off Control -0.3 V min to +13.5V max. Input Reverse Polarity Protection See Fuse section Output Overvoltage VOUT +20% max. Output Current (Note 7) Current-limited. Devices can withstand sustained short circuit without damage. Storage Temperature -55 to +125C Lead Temperature See soldering guidelines Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifications Table is not implied nor recommended. (1) All models are tested and specified with 200 LFM airflow, external 1||10F ceramic/ tantalum output capacitors. External input capacitance varies according to model type. All capacitors are low ESR types. These capacitors are necessary to accommodate our test equipment and may not be required to achieve specified performance in your applications. All models are stable and regulate within spec under no-load conditions. General conditions for Specifications are +25C, VIN =nominal, VOUT = nominal, full load. (2) Input Ripple Current is tested and specified over a 5-20MHz bandwidth. Input filtering is CIN = 33F tantalum, CBUS = 220F electrolytic, LBUS = 12H. (3) Note that Maximum Power Derating curves indicate an average current at nominal input voltage. At higher temperatures and/or lower airflow, the DC-DC converter will tolerate brief full current outputs if the total RMS current over time does not exceed the Derating curve. (4) Mean Time Before Failure is calculated using the Telcordia (Belcore) SR-332 Method 1, Case 3, ground fixed conditions, TPCBOARD = +25C, full output load, natural air convection. (5) The On/Off Control may be driven with external logic or by applying appropriate external voltages which are referenced to Input Common. The On/Off Control Input should use either an open collector/open drain transistor or logic gate which does not exceed +13.5V. (6) Short circuit shutdown begins when the output voltage degrades approximately 2% from the selected setting. (7) The outputs are not intended to sink appreciable reverse current. (8) Output noise may be further reduced by adding an external filter. See I/O Filtering and Noise Reduction. (9) All models are fully operational and meet published specifications, including "cold start" at -40C. (10) Regulation specifications describe the deviation as the line input voltage or output load current is varied from a nominal midpoint value to either extreme. (11) Overvoltage shutdown on 48V input models is not supplied in order to comply with telecom reliability requirements. These requirements attempt continued operation despite significant input overvoltage. (12) Do not exceed maximum power specifications when adjusting the output trim. (13) Note that the converter may operate up to +110C with the baseplate installed. However, thermal self-protection occurs near +110C, and there is a temperature gradient between the hotspot and the baseplate. Therefore, +100C is recommended to avoid thermal shutdown. (14) The converter is guaranteed to turn off at the UV shutdown voltage. (15) At full power, the package temperature of all on-board components must not exceed +128C. Removal of Soldered UVQs from Printed Circuit Boards Should removal of the UVQ from its soldered connection be needed, thoroughly de-solder the pins using solder wicks or de-soldering tools. At no time should any prying or leverage be used to remove boards that have not been properly de-soldered first. Input Source Impedance UVQ converters must be driven from a low ac-impedance input source. The DC-DC's performance and stability can be compromised by the use of highly inductive source impedances. The input circuit shown in Figure 2 is a practical solution that can be used to minimize the effects of inductance in the input traces. For optimum performance, components should be mounted close to the DC-DC converter. I/O Filtering, Input Ripple Current, and Output Noise All models in the UVQ Series are tested/specified for input ripple current (also called input reflected ripple current) and output noise using the circuits and layout shown in Figures 2 and 3. TO OSCILLOSCOPE CURRENT PROBE + VIN 1 +VIN LBUS CBUS CIN - 3 -VIN CIN = 33F, ESR < 700m @ 100kHz CBUS = 220F, ESR < 100m @ 100kHz LBUS = 12H Figure 2. Measuring Input Ripple Current External input capacitors (CIN in Figure 2) serve primarily as energy-storage elements. They should be selected for bulk capacitance (at appropriate frequencies), low ESR, and high rms-ripple-current ratings. The switching nature of DC-DC converters requires that dc voltage sources have low ac impedance as highly inductive source impedance can affect system stability. In Figure 2, CBUS and LBUS simulate a typical dc voltage bus. Your specific system configuration may necessitate additional considerations. www.murata-ps.com/support MDC_UVQ Models.F02 Page 19 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters In critical applications, output ripple/noise (also referred to as periodic and random deviations or PARD) can be reduced below specified limits using filtering techniques, the simplest of which is the installation of additional external output capacitors. Output capacitors function as true filter elements and should be selected for bulk capacitance, low ESR, and appropriate frequency response. On/Off Control The primary-side, Remote On/Off Control function (pin 2) can be specified to operate with either positive or negative logic. Positive-logic devices ("P" suffix) are enabled when pin 2 is left open or is pulled high. Positive-logic devices are disabled when pin 2 is pulled low. Negative-logic devices are off when pin 2 is high/open and on when pin 2 is pulled low. See Figure 4. All external capacitors should have appropriate voltage ratings and be located as close to the converter as possible. Temperature variations for all relevant parameters should be taken into consideration. OS-CONTM organic semiconductor capacitors (www.sanyo.com) can be especially effective for further reduction of ripple/noise. The most effective combination of external I/O capacitors will be a function of line voltage and source impedance, as well as particular load and layout conditions. Dynamic control of the remote on/off function is best accomplished with a mechanical relay or an open-collector/open-drain drive circuit (optically isolated if appropriate). The drive circuit should be able to sink appropriate current (see Performance Specifications) when activated and withstand appropriate voltage when deactivated. 1 +SENSE +VOUT +VIN EQUIVALENT CIRCUIT FOR POSITIVE AND NEGATIVE LOGIC MODELS +Vcc 7 8 2 ON/OFF CONTROL C1 -VOUT -SENSE C2 SCOPE CONTROL RLOAD 4 5 C1 = 1F C2 = 10F LOAD 2-3 INCHES (51-76mm) FROM MODULE Figure 3. Measuring Output Ripple/Noise (PARD) Start-Up Threshold and Undervoltage Shutdown Under normal start-up conditions, the UVQ Series will not begin to regulate properly until the ramping input voltage exceeds the Start-Up Threshold. Once operating, devices will turn off when the applied voltage drops below the Undervoltage Shutdown point. Devices will remain off as long as the undervoltage condition continues. Units will automatically re-start when the applied voltage is brought back above the Start-Up Threshold. The hysteresis built into this function avoids an indeterminate on/off condition at a single input voltage. See Performance/Functional Specifications table for actual limits. Start-Up Time The VIN to VOUT Start-Up Time is the interval between the point at which a ramping input voltage crosses the Start-Up Threshold voltage and the point at which the fully loaded output voltage enters and remains within its specified 1% accuracy band. Actual measured times will vary with input source impedance, external input capacitance, and the slew rate and final value of the input voltage as it appears to the converter. The On/Off to VOUT start-up time assumes that the converter is turned off via the Remote On/Off Control with the nominal input voltage already applied. REF 3 -VIN COMMON Figure 4. Driving the Remote On/Off Control Pin Current Limiting (Power limit with current mode control) As power demand increases on the output and enters the specified "limit inception range" (current in voltage mode and power in current mode) limiting circuitry activates in the DC-DC converter to limit/restrict the maximum current or total power available. In voltage mode, current limit can have a "constant or foldback" characteristic. In current mode, once the current reaches a certain range the output voltage will start to decrease while the output current continues to increase, thereby maintaining constant power, until a maximum peak current is reached and the converter enters a "hic-up" (on off cycling) mode of operation until the load is reduced below the threshold level, whereupon it will return to a normal mode of operation. Current limit inception is defined as the point where the output voltage has decreased by a pre-specified percentage (usually a 2% decrease from nominal). Short Circuit Condition (Current mode control) The short circuit condition is an extension of the "Current Limiting" condition. When the monitored peak current signal reaches a certain range, the PWM controller's outputs are shut off thereby turning the converter "off." This is followed by an extended time out period. This period can vary depending on other conditions such as the input voltage level. Following this time out period, the PWM controller will attempt to re-start the converter by initiating a "normal start cycle" which includes softstart. If the "fault condition" persists, another "hic-up" cycle is initiated. This "cycle" can and will continue indefinitely until such time as the "fault condition" is removed, at which time the converter will resume "normal operation." Operating in the "hic-up" mode during a fault condition is advantageous in that average input and output power levels are held low preventing excessive internal increases in temperature. www.murata-ps.com/support MDC_UVQ Models.F02 Page 20 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Thermal Shutdown UVQ converters are equipped with thermal-shutdown circuitry. If the internal temperature of the DC-DC converter rises above the designed operating temperature (See Performance Specifications), a precision temperature sensor will power down the unit. When the internal temperature decreases below the threshold of the temperature sensor, the unit will self start. Output Overvoltage Protection The output voltage is monitored for an overvoltage condition via magnetic coupling to the primary side. If the output voltage rises to a fault condition, which could be damaging to the load circuitry (see Performance Specifications), the sensing circuitry will power down the PWM controller causing the output voltage to decrease. Following a time-out period the PWM will restart, causing the output voltage to ramp to its appropriate value. If the fault condition persists, and the output voltages again climb to excessive levels, the overvoltage circuitry will initiate another shutdown cycle. This on/off cycling is referred to as "hiccup" mode. Input Reverse-Polarity Protection If the input-voltage polarity is accidentally reversed, an internal diode will become forward biased and likely draw excessive current from the power source. If the source is not current limited or the circuit appropriately fused, it could cause permanent damage to the converter. Input Fusing Certain applications and/or safety agencies may require the installation of fuses at the inputs of power conversion components. Fuses should also be used if the possibility of a sustained, non-current-limited, input-voltage polarity reversal exists. For Murata Power Solutions' UVQ Series DC-DC Converters, fast-blow fuses are recommended with values no greater than twice the maximum input current. Trimming Output Voltage UVQ converters have a trim capability (pin 6) that enables users to adjust the output voltage from +10% to -20% (refer to the trim equations). Adjustments to the output voltage can be accomplished with a single fixed resistor as shown in Figures 5 and 6. A single fixed resistor can increase or decrease the output voltage depending on its connection. Resistors should be located close to the converter and have TCR's less than 100ppm/C to minimize sensitivity to changes in temperature. If the trim function is not used, leave the trim pin open. 1 +VIN +VOUT 8 1 +VIN +VOUT +SENSE 2 ON/OFF CONTROL TRIM -VIN 7 6 LOAD RTRIM DOWN -SENSE 3 8 -VOUT 5 4 Figure 6. Trim Connections To Decrease Output Voltages Using Fixed Resistors On UVQs, a single resistor connected from the Trim pin (pin 6) to the +Sense (pin 7) will increase the output voltage. A resistor connected from the Trim Pin (pin 6) to the -Sense (pin 5) will decrease the output voltage. Trim adjustments greater than the specified +10%/-20% can have an adverse affect on the converter's performance and are not recommended. Excessive voltage differences between VOUT and Sense, in conjunction with trim adjustment of the output voltage, can cause the overvoltage protection circuitry to activate (see Performance Specifications for overvoltage limits). Temperature/power derating is based on maximum output current and voltage at the converter's output pins. Use of the trim and sense functions can cause output voltages to increase, thereby increasing output power beyond the UVQ's specified rating, or cause output voltages to climb into the output overvoltage region. Therefore: (VOUT at pins) x (IOUT) rated output power The Trim pin (pin 6) is a relatively high impedance node that can be susceptible to noise pickup when connected to long conductors in noisy environments. Soldering Guidelines Murata Power Solutions recommends the specifications below when installing these converters. These specifications vary depending on the solder type. Exceeding these specifications may cause damage to the product. Your production environment may differ; therefore please thoroughly review these guidelines with your process engineers. Wave Solder Operations for through-hole mounted products (THMT) For Sn/Ag/Cu based solders: +SENSE 2 ON/OFF CONTROL TRIM -VIN Maximum Preheat Temperature 6 -VOUT 115 C. Maximum Pot Temperature 270 C. Maximum Solder Dwell Time 7 seconds LOAD RTRIM UP -SENSE 3 7 5 4 For Sn/Pb based solders: Maximum Preheat Temperature 105 C. Maximum Pot Temperature 250 C. Maximum Solder Dwell Time 6 seconds Figure 5. Trim Connections To Increase Output Voltages Using Fixed Resistors www.murata-ps.com/support MDC_UVQ Models.F02 Page 21 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Trim Equations F E AT U R E S A N D O P T I O N S Trim Up Trim Down Remote Sense UVQ-1.5/40-D24 RT UP (k) = 6.23(VO - 1.226) -10.2 VO - 1.5 RTDOWN (k) = 7.64 -10.2 1.5 - VO UVQ-2.5/40-D48, UVQ-2.5/35-D24 RT UP (k) = 10(VO - 1.226) -10.2 VO - 2.5 RTDOWN (k) = 12.26 -10.2 2.5 - VO UVQ-3.3/35-D48 RT UP (k) = 13.3(VO - 1.226) -10.2 VO - 3.3 RTDOWN (k) = 16.31 -10.2 3.3 - VO UVQ-5/25-D24, UVQ-5/20-D48 RT UP (k) = 20.4(VO - 1.226) -10.2 VO - 5 RTDOWN (k) = 25.01 -10.2 5 - VO Note: The Sense and VOUT lines are internally connected through low-value resistors. Nevertheless, if the sense function is not used for remote regulation the user must connect the +Sense to +VOUT and -Sense to -VOUT at the DC-DC converter pins. UVQ series converters employ a sense feature to provide point of use regulation, thereby overcoming moderate IR drops in pcb conductors or cabling. The remote sense lines carry very little current and therefore require minimal cross-sectional-area conductors. The sense lines, which are capacitively coupled to their respective output lines, are used by the feedback control-loop to regulate the output. As such, they are not low impedance points and must be treated with care in layouts and cabling. Sense lines on a pcb should be run adjacent to dc signals, preferably ground. In cables and discrete wiring applications, twisted pair or other techniques should be implemented. UVQ series converters will compensate for drops between the output voltage at the DC-DC and the sense voltage at the DC-DC provided that: [VOUT(+) -VOUT(-)] - [Sense(+) -Sense (-)] 10% VOUT UVQ-12/8-D24, -12/10-D48 RT UP (k) = 49.6(VO - 1.226) -10.2 VO - 12 RTDOWN (k) = 60.45 Contact and PCB resistance losses due to IR drops -10.2 12 - VO 1 -INPUT UVQ-15/7-D24, -D48 RT UP (k) = 62.9(VO - 1.226) -10.2 VO - 15 RTDOWN (k) = +OUTPUT +SENSE 76.56 8 7 IOUT Sense Current -10.2 2 15 - VO ON/OFF CONTROL TRIM 6 LOAD Sense Return UVQ-18/5.6-D24, -18/6-D48 -SENSE 5 IOUT Return RT UP (k) = 75.5(VO - 1.226) -10.2 VO - 18 RTDOWN (k) = 92.9 18 - VO 3 -10.2 101(VO - 1.226) -10.2 VO - 24 RTDOWN (k) = 210.75(VO - 1.226) VO - 48 -10.2 RTDOWN (k) = 4 Figure 8. Remote Sense Circuit Configuration 124.2 24 - VO -10.2 UVQ-48/2.5-D24, -D48 RT UP (k) = -OUTPUT Contact and PCB resistance losses due to IR drops UVQ-24/4.5-D24, -D48 RT UP (k) = +INPUT 250 48 - VO -10.2 Note: Higher output 24V and 48V converters require larger, low-tempco, precision trim resistors. An alternative is a low-TC multi-turn potentiometer (20k typical) connected between +VOUT and -VOUT with the wiper to the Trim pin. Output overvoltage protection is monitored at the output voltage pin, not the Sense pin. Therefore, excessive voltage differences between VOUT and Sense in conjunction with trim adjustment of the output voltage can cause the overvoltage protection circuitry to activate (see Performance Specifications for overvoltage limits). Power derating is based on maximum output current and voltage at the converter's output pins. Use of trim and sense functions can cause output voltages to increase, thereby increasing output power beyond the conveter's specified rating, or cause output voltages to climb into the output overvoltage region. Therefore, the designer must ensure: (VOUT at pins) (IOUT) rated output power www.murata-ps.com/support MDC_UVQ Models.F02 Page 22 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters UVQ Series Aluminum Heatsink The UVQ series converter baseplate can be attached either to an enclosure wall or a heatsink to remove heat from internal power dissipation. The discussion below concerns only the heatsink alternative. The UVQs are available with a low-profile extruded aluminum heatsink kit, models HS-QB25-UVQ, HS-QB50-UVQ, and HS-QB100-UVQ. This kit includes the heatsink, thermal mounting pad, screws and mounting hardware. See the assembly diagram below. Do not overtighten the screws in the tapped holes in the converter (3.5 n-m or 1.9 in-oz. max.). This kit adds excellent thermal performance without sacrificing too much component height. See the Mechanical Outline Drawings for assembled dimensions. If the thermal pad is firmly attached, no thermal compound ("thermal grease") is required. Thermal Performance The HS-QB25-UVQ heatsink has a thermal resistance of 12 C/Watt of internal heat dissipation with "natural convection" airflow (no fans or other mechanical airflow) at sea level altitude. This thermal resistance assumes that the heatsink is firmly attached using the supplied thermal pad and that there is no nearby wall or enclosure surface to inhibit the airflow. The thermal pad adds a negligible series resistance of approximately 0.5C/Watt so that the total assembled resistance is 12.5C/Watt. Be aware that we need to handle only the internal heat dissipation, not the full power output of the converter. This internal heat dissipation is related to the efficiency as follows: Power Dissipation [Pd] = Power In - Power Out [1] Power Out / Power In = Efficiency [in %] / 100 [2] 0!. (%!$ 3#2%7 - 8 - 0,#3 Power Dissipation [Pd] = Power In x (1 -Efficiency%/100) [3] Power Dissipation [Pd] = Power Out x (1 / (Efficiency%/100) - 1) [4] Efficiency of course varies with input voltage and the total output power. Please refer to the Performance Curves. ,/#+ 7!3(%2 - 0,#3 &,!4 7!3(%2 ./ 0,#3 Since many applications do include fans, here is an approximate equation to calculate the net thermal resistance: R [at airflow] = R [natural convection] / (1 + (Airflow in LFM) x [Airflow Constant]) [5] Where, R [at airflow] is the net thermal resistance (in C/W) with the amount of airflow available and, (%!43).+ R [natural convection] is the still air total path thermal resistance or in this case 12.5C/Watt and, "Airflow in LFM" is the net air movement flow rate immediately at the converter. (%!4 42!.3&%2 0!$ 0EEL OFF WHITE PLASTIC BACKING MATERIAL BEFORE ATTACHING TO HEATSINK Figure 7. Model UVQ Heatsink Assembly Diagram When assembling these kits onto the converter, include ALL kit hardware to assure adequate mechanical capture and proper clearances. Thread relief is 0.090" (2.3mm). This equation simplifies an otherwise complex aerodynamic model but is a useful starting point. The "Airflow Constant" is dependent on the fan and enclosure geometry. For example, if 200 LFM of airflow reduces the effective natural convection thermal resistance by one half, the airflow constant would be 0.005. There is no practical way to publish a "one size fits all" airflow constant because of variations in airflow direction, heatsink orientation, adjacent walls, enclosure geometry, etc. Each application must be determined empirically and the equation is primarily a way to help understand the cooling arithmetic. This equation basically says that small amounts of forced airflow are quite effective removing the heat. But very high airflows give diminishing returns. Conversely, no forced airflow causes considerable heat buildup. At zero airflow, cooling occurs only because of natural convection over the heatsink. Natural convection is often well below 50 LFM, not much of a breeze. While these equations are useful as a conceptual aid, most users find it very difficult to measure actual airflow rates at the converter. Even if you know the velocity specifications of the fan, this does not usually relate directly to the enclosure geometry. Be sure to use a considerable safety margin doing thermal analysis. If in doubt, measure the actual heat sink temperature with a calibrated thermocouple, RTD or thermistor. Safe operation should keep the heat sink below 100C. www.murata-ps.com/support MDC_UVQ Models.F02 Page 23 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Calculating Maximum Power Dissipation To determine the maximum amount of internal power dissipation, find the ambient temperature inside the enclosure and the airflow (in Linear Feet per Minute - LFM) at the converter. Determine the expected heat dissipation using the Efficiency curves and the converter Input Voltage. You should also compensate for lower atmospheric pressure if your application altitude is considerably above sea level. The general proceedure is to compute the expected temperature rise of the heatsink. If the heatsink exceeds +100C. either increase the airflow and/or reduce the power output. Start with this equation: Internal Heat Dissipation [Pd in Watts] = (Ts - Ta)/R [at airflow] [6] where "Ta" is the enclosure ambient air temperature and, where "Ts" is the heatsink temperature and, where "R [at airflow]" is a specific heat transfer thermal resistance (in degrees Celsius per Watt) for a particular heat sink at a set airflow rate. We have already estimated R [at airflow] in the equations above. Note particularly that Ta is the air temperature inside the enclosure at the heatsink, not the outside air temperature. Most enclosures have higher internal temperatures, especially if the converter is "downwind" from other heat-producing circuits. Note also that this "Pd" term is only the internal heat dissipated inside the converter and not the total power output of the converter. We can rearrange this equation to give an estimated temperature rise of the heatsink as follows: Heat Sink Example Assume an efficiency of 92% and power output of 100 Watts. Using equation [4], Pd is about 8.7 Watts at an input voltage of 48 Volts. Using +30C ambient temperature inside the enclosure, we wish to limit the heat sink temperature to +90C maximum baseplate temperature to stay well away from thermal shutdown. The +90C. figure also allows some margin in case the ambient climbs above +30C or the input voltage varies, giving us less than 92% efficiency. The heat sink and airflow combination must have the following characteristics: 8.7 W = (90-30) / R[airflow] or, R[airflow] = 60/8.7 = 6.9C/W Since the ambient thermal resistance of the heatsink and pad is 12.5C/W, we need additional forced cooling to get us down to 6.9C/W. Using a hypothetical airflow constant of 0.005, we can rearrange equation [5] as follows: (Required Airflow, LFM) x (Airflow Constant) = R[Nat.Convection] / R[at airflow] -1 or, (Required Airflow, LFM) x (Airflow Constant) = 12.5/6.9 -1 = 0.81 and, rearranging again, (Required Airflow, LFM) = 0.81/0.005 = 162 LFM 162 LFM is the minumum airflow to keep the heatsink below +90C. Increase the airflow to several hundred LFM to reduce the heatsink temperature further and improve life and reliability. 2.28 (57.91) Ts = (Pd x R [at airflow]) + Ta [7] 1.860 (47.24) Heatsink Kit * Model Number Still Air (Natural convection) thermal resistance Heatsink height (see drawing) HS-QB25-UVQ 12C/Watt 0.25" (6.35mm) HS-QB50-UVQ 10.6C/Watt 0.50" (12.7mm) HS-QB100-UVQ 8C/Watt 1.00" (25.4mm) 1.03 1.45 (26.16) (36.83) * Kit includes heatsink, thermal pad and mounting hardware. These are non-RoHS models. For RoHS-6 versions, add "-C" to the model number (e.g., HS-QB25-UVQ-C). 0.140 DIA. (3.56) (4 PLACES) * MATERIAL: BLACK ANODIZED ALUMINUM 0.10 (2.54) * UVQ SERIES HEATSINKS ARE AVAILABLE IN 3 HEIGHTS: 0.25 (6.35), 0.50 (12.70) AND 1.00 (25.4) Dimensions in inches (mm) www.murata-ps.com/support MDC_UVQ Models.F02 Page 24 of 25 UVQ Series Low Profile, Isolated Quarter Brick 2.5-40 Amp DC-DC Converters Vertical Wind Tunnel IR Transparent optical window Unit under test (UUT) Variable speed fan Murata Power Solutions employs a computer controlled custom-designed closed loop vertical wind tunnel, infrared video camera system, and test instrumentation for accurate airflow and heat dissipation analysis of power products. The system includes a precision low flow-rate anemometer, variable speed fan, power supply input and load controls, temperature gauges, and adjustable heating element. The IR camera monitors the thermal performance of the Unit Under Test (UUT) under static steady-state conditions. A special optical port is used which is transparent to infrared wavelengths. IR Video Camera Heating element Precision low-rate anemometer 3" below UUT Ambient temperature sensor Airflow collimator Figure 9. Vertical Wind Tunnel Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED Both through-hole and surface mount converters are soldered down to a 10" x 10" host carrier board for realistic heat absorption and spreading. Both longitudinal and transverse airflow studies are possible by rotation of this carrier board since there are often significant differences in the heat dissipation in the two airflow directions. The combination of adjustable airflow, adjustable ambient heat, and adjustable Input/Output currents and voltages mean that a very wide range of measurement conditions can be studied. The collimator reduces the amount of turbulence adjacent to the UUT by minimizing airflow turbulence. Such turbulence influences the effective heat transfer characteristics and gives false readings. Excess turbulence removes more heat from some surfaces and less heat from others, possibly causing uneven overheating. Both sides of the UUT are studied since there are different thermal gradients on each side. The adjustable heating element and fan, built-in temperature gauges, and no-contact IR camera mean that power supplies are tested in real-world conditions. This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. (c) 2015 Murata Power Solutions, Inc. www.murata-ps.com/support MDC_UVQ Models.F02 Page 25 of 25