Solid State Relay G3R-I/O 407
Solid State Relay
G3R-I/O
Compact SSRs for I/O Interface with High
Dielectric Strength Requirements
• High-speed models with optimum input ratings for a variety
of sensors are available.
• Input Modules and Output Modules that have the same
form-factor as the G2R.
• Using a coupler approved by VDE 0884 and assuring an
I/O dielectric strength of 4 kV.
• Incorporating an easy-to-see monitoring indicator.
• Approved by UL, CSA, and TÜV. (“-UTU” models)
Ordering Information
To Order: Select the part number and add the desired coil voltage rating, (e.g., G3R-IAZR1SN-DC5)
■Input Module
■Output Module
Note: When ordering a UL, CSA and EN (TÜV) approved model, add “-UTU” to the model number as shown below:
Example: G3R-OA202SZN-UTU DC5-24.
■I/O Indication
I/O module classification and AC/DC use are indicated on the mark
affixed to the top of the product.
Isolation Indicator Response speed Logic level Rated input
voltage
Model
Supply voltage Supply current
Photocoupler Yes — 4 to 32 VDC 0.1 to 100 mA 100 to 240 VAC G3R-IAZR1SN
High-speed
(1 kHz)
5 VDC G3R-IDZR1SN
12 to 24 VDC
Low-speed
(10 Hz)
5 VDC G3R-IDZR1SN-1
12 to 24 VDC
Isolation Indicator Zero cross
function
Rated output
load
Rated input
voltage
Model
Phototriac Yes Yes 2 A at 100 to 240 VAC 5 to 24 VDC G3R-OA202SZN
No G3R-OA202SLN
Photocoupler — 2 A at 5 to 48 VDC G3R-ODX02SN
1.5 A at 48 to 200 VDC G3R-OD201SN
Mark indication Specification
AC IN Input module, AC input
DC IN Input module, DC input
AC OUT Output module, AC output
DC OUT Output module, DC output
Mark attached to the top of the product
408 Solid State Relay G3R-I/O
Specifications
■Ratings (at an Ambient Temperature of 25°C)
Input Module
Input
Output
Output Module
Input
Output
Note: The minimum current value is measured at 10°C min.
Model Rated voltage Operating voltage Input current Must operate
voltage
Must release
voltage
G3R-IAZR1SN 100 to 240 VAC 60 to 264 VAC 15 mA max. 60 VAC max. 20 VAC min.
G3R-IDZR1SN 5 VDC 4 to 6 VDC 8 mA max. 4 VDC max. 1 VDC min.
12 to 24 VDC 6.6 to 32 VDC 6.6 VDC max. 3.6 VDC min.
G3R-IDZR1SN-1 5 VDC 4 to 6 VDC 4 VDC max. 1 VDC min.
12 to 24 VDC 6.6 to 32 VDC 6.6 VDC max. 3.6 VDC min.
Model Logic level supply voltage Logic level supply current
G3R-IAZR1SN 4 to 32 VDC 0.1 to 100 mA
G3R-IDZR1SN
G3R-IDZR1SN-1
Model Rated voltage Operating voltage Input current Must operate
voltage
Must release
voltage
G3R-OA202SZN 5 to 24 VDC 4 to 32 VDC 15 mA max.
(at 25°C)
4 VDC max. 1 VDC min.
G3R-OA202SLN
G3R-ODX02SN 8 mA max.
G3R-OD201SN
Model Rated load voltage Load voltage range Load current (see note) Inrush current
G3R-OA202SZN 100 to 240 VAC 75 to 264 VAC 0.05 to 2 A 30 A (60 Hz, 1 cycle)
G3R-OA202SLN
G3R-ODX02SN 5 to 48 VDC 4 to 60 VDC 0.01 to 2 A 8 A (10 ms)
G3R-OD201SN 48 to 200 VDC 40 to 200 VDC 0.01 to 1.5 A 8 A (10 ms)
Solid State Relay G3R-I/O 409
Characteristics
■Input Module
■Output Module
Item G3R-IAZR1SN G3R-IDZR1SN G3R-IDZR1SN-1
Operate time 20 ms max. 0.1 ms max. 15 ms max.
Release time 20 ms max. 0.1 ms max. 15 ms max.
Response frequency 10 Hz 1 kHz 10 Hz
Output ON voltage drop 1.6 V max.
Leakage current 5 μA max.
Insulation resistance 100 MΩmin. between input and output
Dielectric strength 4,000 VAC, 50/60 Hz for 1 min. between input and output
Vibration resistance 10 to 55 Hz, 1.5-mm double amplitude
Shock resistance 1,000 m/s2 {approx. 100G}
Ambient temperature Operating: -30°C to 80°C (with no icing)
Storage: -30°C to 100°C (with no icing)
Approved standards UL File No. E64562
CSA File No. LR35535
TÜV File No. R9650094 (EN60950)
Ambient humidity Operating: 45% to 85%
Weight Approx. 18 g
Item G3R-OA202SZN G3R-OA202SLN G3R-ODX02SN G3R-OA201SN
Operate time 1/2 of load power source cycle + 1 ms max. 1 ms max.
Release time 1/2 of load power source cycle + 1 ms max. 2 ms max.
Response frequency 20 Hz 100 Hz
Output ON voltage drop 1.6 V max. 2.5 V max.
Leakage current 1.5 mA max. 1 mA max.
Insulation resistance 100 MΩmin. between input and output
Dielectric strength 4,000 VAC, 50/60 Hz for 1 min. between input and output
Vibration resistance 10 to 55 Hz, 1.5-mm double amplitude
Shock resistance 1,000 m/s2 {approx. 100G}
Ambient temperature Operating: -30°C to 80°C (with no icing)
Storage: -30°C to 100°C (with no icing)
Approved standards UL File No. E64562
CSA File No. LR35535
TÜV File No. R9650094 (EN60950)
Ambient humidity Operating: 45% to 85%
Weight Approx. 18 g
410 Solid State Relay G3R-I/O
Engineering Data
Load Current vs. Ambient Temperature
Inrush Current Resistivity
Non-repetitive (Keep the inrush current to half the rated value if it occurs repetitively.)
2
1.5
−30
0.7
0.5
1
−20 0 20 30 40 55 60 80 100
1.4
−30 −20 0 20 40 55 60 80 100
2
1.5
0.5
1
0.6
1.1
2
1.5
0.5
1
−30 −20 0 20 40 55 60 80 100
1.4
4-point mounting (see note 1)
16-point mounting (see note 2) 4-point mounting (see note 1)
4-point mounting (see note 1)
16-point mounting (see note 2)
G3R-OA202SZN(-UTU)/OA202SLN(-UTU) G3R-OD201SN(-UTU) (40 to 200 VAC)G3R-ODX02SN(-UTU) (4 to 60 VDC)
Ambient temperature (
°
C)
Load current (A)
Ambient temperature (
°
C)
Load current (A)
Ambient temperature (
°
C)
Load current (A)
Note: 1. When G730-Z0M04-B is mounted.
2. When G70A-Z0C16 is mounted.
Single-point
mounting Single-point
mounting
16-point mounting
(see note 2)
Single-point
mounting
30
20
10
10 30 50 100 200 500 1000 5000
10
9
8
7
6
5
4
3
2
1
010 30 50 100 500 1000 2000300
10
9
8
7
6
5
4
3
2
1
010 30 50 100 500 1000 2000300
G3R-OA202SZN(-UTU)/OA202SLN(-UTU) G3R-OD201SN(-UTU)G3R-ODX02SN(-UTU)
Inrush current (A)
Energized time (ms)
Inrush current (A)
Energized time (ms)
Inrush current (A)
Energized time (ms)
Solid State Relay G3R-I/O 411
Dimensions
Unit: mm (inch)
■G3R
■Connecting Sockets
4
57.5
9.6
3
4
1
2
20
0.5
5.2
17.4
4.7
4.75
4.75
0.5
10
15
(+)
(−)
3
4
1 5
(−) (+)
13 max. 28 max.
29 max.
Load
Input
Terminal Arrangement/
Internal Connections
(Bottom View)
58.5 *
Five, M3.5×8
12
P2RF-05
71.5 max.
19.5 max.
54 max.
30 max.
4 dia.
4.2-dia. hole
P2RF-05 Socket
G3R I/O Relay
M3 (M3 x16) or
3.2-dia. hole
* Indicates a value when using the PFP-@N
Supporting Rail.
The value is 67.5 when using the PFP-@N2.
62.5 **
(66.5)***
P2RF-05-E
G3R I/O Relay
3.2-dia. hole
M3 or 3.5-dia. hole
59 max.
48 max.
M3.5 screw
85.5 max.
61 max.
3.5-dia.
hole
PFRF-05-E
Socket
** Indicates a value when using the PFP-@N
Supporting Rail with the P2RF-05-E
The value is 71.5 when using the PFP-@N2.
*** Indicates a value when using the PFP-@N
Supporting Rail with the P2RF-08-E
The value is 75.5 when using the PFP-@N2.
P2R-05A 14.5 max.
35.5 max.
Five, 3x1.5-dia. hole
G3R I/O Relay
P2R-05A Socket
36 max.
(Panel thickness must
be 1.6 to 2.0 mm.) (For use when mounting in a panel or in
the P2R-P mounting plate )
412 Solid State Relay G3R-I/O
■Socket Mounting Plate
Use the P2R-P Socket Mounting Plate when arranging several P2R-05A Sockets in a row.
P2R-P
■Approvals
UL Recognized (File No. E64562) / CSA Certified (File No. LR35535)
P2R-05P
Dimensional tolerance is ±0.1.
G3R I/O Relay
P2R-05P Socket
Five, 1.6-dia. hole
35.5 max.
14.5 max.
36 max.
P2R-057P G3R I/O Relay
P2R-057P Socket
Five, 1.6-dia. hole
14 max.
32 max.
41 max.
Square hole
R2.25
10 ellipses
Model G3R- Module type Rating
IAZR1SN Input 100 to 240 VAC
IDZR1SN Input 5 VDC, 12 to 24 VDC
IDZR1SN-1 Input 5 VDC, 12 to 24 VDC
OA202SZN Output 5 to 24 VDC
OA202SLN Output 5 to 24 VDC
ODX02SN Output 5 to 24 VDC
OD201SN Output 5 to 24 VDC
Model G3R- Module type Output rating
IAZR1SN Input 32 VDC, 100 mA (General Purpose)
IDZR1SN Input 32 VDC, 100 mA (General Purpose)
IDZR1SN-1 Input 32 VDC, 100 mA (General Purpose)
OA202SZN Output 264 VAC, 2 A (General Purpose)
264 VAC, 1 A (Tungsten)
264 VAC, 1 A FLA, 6 A LRA
OA202SLN Output 264 VAC, 2 A (General Purpose)
264 VAC, 1 A (Tungsten)
264 VAC, 1 A FLA, 6 A LRA
ODX02SN Output 60 VDC, 2 A (General Purpose)
60 VDC, 1 A (Tungsten)
OD201SN Output 200 VDC, 1.5 A (General Purpose)
200 VDC, 0.75 A (Tungsten)
Solid State Relay G3R-I/O 413
Precautions
■Connection
With the SSR for DC switching, the load can be connected to either
positive or negative output terminal of the SSR.
■Protective element
Since the SSR does not incorporate an overvoltage absorption com-
ponent, be sure to connect an overvoltage absorption component
when using the SSR under an inductive load.
■Precaution of Mounting Output Modules
G3R G3R G3R
With up to four G3R SSRs mounted closely and
side by side, 2-A loads can be switched.
With a G3R SSRs mounted every other slot,
2-A loads can be switched.
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-
out notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-
tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importa-
tion, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liabil-
ity and in addition to other remedies) cancel any unshipped portion of Prod-
ucts sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security inter-
est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original trans-
portation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or oth-
erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-
gation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsi-
ble for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were prop-
erly handled, stored, installed and maintained and not subject to contamina-
tion, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Compa-
nies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environ-
ments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for pub-
lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, inves-
tigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or set-
tle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-
sive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law princi-
ples). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability
. If any provi-
sion hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Compa-
nies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Prod-
uct in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equip-
ment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or prop-
erty. Please know and observe all prohibitions of use applicable to this Prod-
uct.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-
ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitabil-
ity and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application require-
ments. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our prac-
tice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifica-
tions of the Product may be changed without any notice. When in doubt, spe-
cial part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
Cat. No. J25I-E-01 06/09 Note: Specications are subject to change. © 2010 Omron Electronics LLC
OMRON CANADA, INC. • HEAD OFFICE
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
OMRON ELECTRONICS MEXICO SA DE CV • HEAD OFFICE
OMRON ARGENTINA • SALES OFFICE
OMRON CHILE • SALES OFFICE
OTHER OMRON LATIN AMERICA SALES
OMRON ELECTRONICS LLC • THE AMERICAS HEADQUARTERS
OMRON EUROpE B.V.
