Freescale Semiconductor Technical Data MSC8122 Rev. 12, 4/2006 MSC8122 Quad Core 16-Bit Digital Signal Processor SC140 Extended Core SC140 Extended Core SC140 Extended Core MQBus SC140 Extended Core 128 128 SQBus Boot ROM 64 Local Bus IP Master 32 Timers Memory Controller M2 RAM UART RS-232 4 TDMs PLL/Clock JTAG Port IPBus PLL GPIO GIC 32 Ethernet 64 System Interface DMA Internal Local Bus SIU Registers Bridge 64 Internal System Bus GPIO Pins Interrupts Direct Slave Interface (DSI) Memory Controller What's New? Rev. 12 includes the following: 8 Hardware Semaphores JTAG The raw processing power of this highly integrated systemon- a-chip device will enable developers to create nextgeneration networking products that offer tremendous channel densities, while maintaining system flexibility, scalability, and upgradeability. The MSC8122 is offered in three core speed levels: 300, 400, and 500 MHz. MII/RMII/SMII * Chapter 2 updates Figure 2-11 for reset timing. DSI Port 32/64 System Bus 32/64 Figure 1. MSC8122 Block Diagram The MSC8122 is a highly integrated system-on-a-chip that combines four SC140 extended cores with an RS-232 serial interface, four time-division multiplexed (TDM) serial interfaces, thirty-two general-purpose timers, a flexible system interface unit (SIU), an Ethernet interface, and a multi-channel DMA engine. The four extended cores can deliver a total 4800/6400/8000 DSP MMACS performance at 300/400/500 MHz. Each core has four arithmetic logic units (ALUs), internal memory, a write buffer, and two interrupt controllers. The MSC8122 targets high-bandwidth highly computational DSP applications and is optimized for wireless transcoding and packet telephony as well as high-bandwidth base station applications. The MSC8122 delivers enhanced performance while maintaining low power dissipation and greatly reducing system cost. (c) Freescale Semiconductor, Inc., 2004, 2006. All rights reserved. Table of Contents Table of Contents Features...............................................................................................................................................................iv Product Documentation ......................................................................................................................................ix Chapter 1 Signals/Connections 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 Chapter 2 Specifications 2.1 2.2 2.3 2.4 2.5 Chapter 3 Maximum Ratings.............................................................................................................................................2-1 Recommended Operating Conditions...............................................................................................................2-2 Thermal Characteristics ....................................................................................................................................2-3 DC Electrical Characteristics............................................................................................................................2-3 AC Timings.......................................................................................................................................................2-4 Packaging 3.1 3.2 Chapter 4 Power Signals ...................................................................................................................................................1-3 Clock Signals ....................................................................................................................................................1-3 Reset and Configuration Signals.......................................................................................................................1-3 Direct Slave Interface, System Bus, Ethernet, and Interrupt Signals ...............................................................1-4 Memory Controller Signals ............................................................................................................................1-14 GPIO, TDM, UART, and Timer Signals.........................................................................................................1-16 Dedicated Ethernet Signals.............................................................................................................................1-23 EOnCE Event and JTAG Test Access Port Signals ........................................................................................1-24 Reserved Signals.............................................................................................................................................1-24 Package Description .........................................................................................................................................3-1 MSC8122 Package Mechanical Drawing .......................................................................................................3-20 Design Considerations 4.1 4.2 4.3 4.4 4.5 Start-up Sequencing Recommendations ...........................................................................................................4-1 Power Supply Design Considerations...............................................................................................................4-1 Connectivity Guidelines ...................................................................................................................................4-3 External SDRAM Selection..............................................................................................................................4-4 Thermal Considerations....................................................................................................................................4-5 Data Sheet Conventions OVERBAR Used to indicate a signal that is active when pulled low (For example, the RESET pin is active when low.) "asserted" Means that a high true (active high) signal is high or that a low true (active low) signal is low "deasserted" Means that a high true (active high) signal is low or that a low true (active low) signal is high Examples: Signal/Symbol Logic State Signal State Voltage PIN True Asserted VIL/VOL PIN False Deasserted VIH/VOH PIN True Asserted VIH/VOH PIN False Deasserted VIL/VOL Note: Values for VIL, VOL, VIH, and VOH are defined by individual product specifications. MSC8122 Technical Data, Rev. 12 ii Freescale Semiconductor Data Sheet Conventions Address Register File Program Sequencer SC140 Core Address ALU JTAG EOnCE Data ALU Register File Data ALU Power Management M1 RAM SC140 Core Xa Xb P 64 64 128 Instruction Cache QBus Interface QBC 128 QBus PIC IRQs LIC IRQs QBus Bank 1 QBus Bank 3 MQBus 128 SQBus Local Bus 128 64 Notes: 1. The arrows show the data transfer direction. 2. The QBus interface includes a bus switch, write buffer, fetch unit, and a control unit that defines four QBus banks. In addition, the QBC handles internal memory contentions. Figure 2. SC140 Extended Core Block Diagram MSC8122 Technical Data, Rev. 12 Freescale Semiconductor iii Features Features Feature Description SC140 Cores Four SC140 cores: * Up to 8000 MMACS using 16 ALUs running at up to 500 MHz. * A total of 1436 KB of internal SRAM (224 KB per core + 16 KB ICache per core + the shared M2 memory). Each SC140 core provides the following: * Up to 2000 MMACS using an internal 500 MHz clock. A MAC operation includes a multiply-accumulate command with the associated data move and pointer update. * 4 ALUs per SC140 core. * 16 data registers, 40 bits each. * 27 address registers, 32 bits each. * Hardware support for fractional and integer data types. * Very rich 16-bit wide orthogonal instruction set. * Up to six instructions executed in a single clock cycle. * Variable-length execution set (VLES) that can be optimized for code density and performance. * IEEE Std 1149.1TM JTAG port. * Enhanced on-device emulation (EOnCE) with real-time debugging capabilities. Extended Core Each SC140 core is embedded within an extended core that provides the following: * 224 KB M1 memory that is accessed by the SC140 core with zero wait states. * Support for atomic accesses to the M1 memory. * 16 KB instruction cache, 16 ways. * A four-entry write buffer that frees the SC140 core from waiting for a write access to finish. * External cache support by asserting the global signal (GBL) when predefined memory banks are accessed. * Programmable interrupt controller (PIC). * Local interrupt controller (LIC). Multi-Core Shared Memories M2-Accessible MultiCore Bus (MQBus) Internal PLL * 476 KB M2 memory (shared memory) working at the core frequency, accessible from the local bus, and accessible from all four SC140 cores using the MQBus. * 4 KB bootstrap ROM. * * * * * A QBus protocol multi-master bus connecting the four SC140 cores to the M2 memory. Data bus access of up to 128-bit read and up to 64-bit write. Operation at the SC140 core frequency. A central efficient round-robin arbiter controlling SC140 core access on the MQBus. Atomic operation control of access to M2 memory by the four SC140 cores and the local bus. * Generates up to 500 MHz core clock and up to166 MHz bus clocks for the 60x-compatible local and system buses and other modules. * PLL values are determined at reset based on configuration signal values. * * * * * 60x-Compatible System Bus 64/32-bit data and 32-bit address 60x bus. Support for multiple-master designs. Four-beat burst transfers (eight-beat in 32-bit wide mode). Port size of 64, 32, 16, and 8 controlled by the internal memory controller. Bus can access external memory expansion or off-device peripherals, or it can enable an external host device to access internal resources. * Slave support, direct access by an external host to internal resources including the M1 and M2 memories. * On-device arbitration between up to four master devices. Direct Slave Interface (DSI) A 32/64-bit wide slave host interface that operates only as a slave device under the control of an external host processor. * 21-25 bit address, 32/64-bit data. * Direct access by an external host to internal and external resources, including the M1 and the M2 memories as well as external devices on the system bus. * Synchronous and asynchronous accesses, with burst capability in the synchronous mode. * Dual or Single strobe modes. * Write and read buffers improve host bandwidth. * Byte enable signals enables 1, 2, 4, and 8 byte write access granularity. * Sliding window mode enables access with reduced number of address pins. * Chip ID decoding enables using one CS signal for multiple DSPs. * Broadcast CS signal enables parallel write to multiple DSPs. * Big-endian, little-endian, and munged little-endian support. 3-Mode Signal Multiplexing * 64-bit DSI, 32-bit system bus. * 32-bit DSI, 64-bit system bus. * 32-bit DSI, 32-bit system bus. MSC8122 Technical Data, Rev. 12 iv Freescale Semiconductor Features Feature Description Memory Controller Flexible eight-bank memory controller: * Three user-programmable machines (UPMs), general-purpose chip-select machine (GPCM), and a page-mode SDRAM machine. * Glueless interface to SRAM, page mode SDRAM, DRAM, EPROM, Flash memory, and other user-definable peripherals. * Byte enables for either 64-bit or 32-bit bus width mode. * Eight external memory banks (banks 0-7). Two additional memory banks (banks 9, 11) control IPBus peripherals and internal memories. Each bank has the following features: -- 32-bit address decoding with programmable mask. -- Variable block sizes (32 KB to 4 GB). -- Selectable memory controller machine. -- Two types of data errors check/correction: normal odd/even parity and read-modify-write (RMW) odd/even parity for single accesses. -- Write-protection capability. -- Control signal generation machine selection on a per-bank basis. -- Support for internal or external masters on the system bus. -- Data buffer controls activated on a per-bank basis. -- Atomic operation. -- RMW data parity check (on system bus only). -- Extensive external memory-controller/bus-slave support. -- Parity byte select pin, which enables a fast, glueless connection to RMW-parity devices (on the system bus only). -- Data pipeline to reduce data set-up time for synchronous devices. * * * * Multi-Channel DMA Controller * * * * Time-Division Multiplexing (TDM) 16 time-multiplexed unidirectional channels. Services up to four external peripherals. Supports DONE or DRACK protocol on two external peripherals. Each channel group services 16 internal requests generated by eight internal FIFOs. Each FIFO generates: -- A watermark request to indicate that the FIFO contains data for the DMA to empty and write to the destination. -- A hungry request to indicate that the FIFO can accept more data. Priority-based time-multiplexing between channels using 16 internal priority levels. Round-robin time-multiplexing between channels. A flexible channel configuration: -- All channels support all features. -- All channels connect to the system bus or local bus. Flyby transfers in which a single data access is transferred directly from the source to the destination without using a DMA FIFO. Up to four independent TDM modules, each with the following features: * Optional operating configurations: -- Totally independent receive and transmit channels, each having one data line, one clock line, and one frame sync line. -- Four data lines with one clock and one frame sync shared among the transmit and receive lines. * Connects gluelessly to most T1/E1 framers as well as to common buses such as the ST-BUS. * Hardware A-law/-law conversion. * Up to 62.5 Mbps per TDM (62.5 MHz bit clock if one data line is used, 31.25 MHz if two data lines are used, 15.63 MHz if four data lines are used). * Up to 256 channels. * Up to 16 MB per channel buffer (granularity 8 bytes), where A/ law buffer size is double (granularity 16 byte). * Receive buffers share one global write offset pointer that is written to the same offset relative to their start address. * Transmit buffers share one global read offset pointer that is read from the same offset relative to their start address. * All channels share the same word size. * Two programmable receive and two programmable transmit threshold levels with interrupt generation that can be used, for example, to implement double buffering. * Each channel can be programmed to be active or inactive. * 2-, 4-, 8-, or 16-bit channels are stored in the internal memory as 2-, 4-, 8-, or 16-bit channels, respectively. * The TDM Transmitter Sync Signal (TxTSYN) can be configured as either input or output. * Frame Sync and Data signals can be programmed to be sampled either on the rising edge or on the falling edge of the clock. * Frame sync can be programmed as active low or active high. * Selectable delay (0-3 bits) between the Frame Sync signal and the beginning of the frame. * MSB or LSB first support. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor v Features Feature Description Ethernet Controller * Designed to comply with IEEE(R) Std 802(R) including Std. 802.3TM, 802.3uTM, 802.3xTM, and 802.3acTM. * Three Ethernet physical interfaces: -- 10/100 Mbps MII. -- 10/100 Mbps RMII. -- 10/100 Mbps SMII. * Full and half-duplex support. * Full-duplex flow control (automatic PAUSE frame generation or software programmed PAUSE frame generation and recognition). * Out-of-sequence transmit queue for initiating flow-control. * Programmable maximum frame length supports jumbo frames (up to 9.6k) and virtual local area network (VLAN) tags and priority. * Retransmission from transmit FIFO following a collision. * CRC generation and verification of inbound/outbound packets. * Address recognition: -- Each exact match can be programmed to be accepted or rejected. -- Broadcast address (accept/reject). -- Exact match 48-bit individual (unicast) address. -- Hash (256-bit hash) check of individual (unicast) addresses. -- Hash (256-bit hash) check of group (multicast) addresses. -- Promiscuous mode. * Pattern matching: -- Up to 16 unique 4-byte patterns. -- Pattern match on bit-basis. -- Matching range up to 256 bytes deep into the frame. -- Offsets to a maximum of 252 bytes. -- Programmable pattern size in 4-byte increments up to 64 bytes. -- Accept or reject frames if a match is detected. -- Up to eight unicast addresses for exact matches. -- Pattern matching accepts/rejects IP addresses. * Filing of receive frames based on pattern match; prioritization of frames. * Insertion with expansion or replacement for transmit frames; VLAN tag insertion. * RMON statistics. * Master DMA on the local bus for fetching descriptors and accessing the buffers. * Ethernet PHY can be exposed either on GPIO pins or on the high most significant bits of the DSI/system when the DSI and the system bus are both 32 bits. * MPC8260 8-byte width buffer descriptor mode as well as 32 byte width buffer descriptor mode. * MII Bridge (MIIGSK): -- Programmable selection of the 50 MHz RMII reference clock source (external or internal). -- Independent 2 bit wide transmit and receive data paths. -- Six operating modes. -- Four general-purpose control signals. -- Programmable transmitted inter-frame bits to support inter-frame gap for frames in the SMII domain. * SMII features: -- Multiplexed only with GPIO signals -- Convey complete MII information between the PHY and MAC. -- Allow direct MAC-to-MAC communication in SMII mode. -- Can generate an interrupt request line while receiving inter-frame segments. MSC8122 Technical Data, Rev. 12 vi Freescale Semiconductor Features Feature Description * * * * * * * * * * UART * * * * * * * Two signals for transmit data and receive data. No clock, asynchronous mode. Can be serviced either by the SC140 DSP cores or an external host on the system bus or the DSI. Full-duplex operation. Standard mark/space non-return-to-zero (NRZ) format. 13-bit baud rate selection. Programmable 8-bit or 9-bit data format. Separately enabled transmitter and receiver. Programmable transmitter output polarity. Two receiver wake-up methods: -- Idle line wake-up. -- Address mark wake-up. Separate receiver and transmitter interrupt requests. Nine flags, the first five can generate interrupt request: -- Transmitter empty. -- Transmission complete. -- Receiver full. -- Idle receiver input. -- Receiver overrun. -- Receiver active. -- Noise error. -- Framing error. -- Parity error. Receiver framing error detection. Hardware parity checking. 1/16 bit-time noise detection. Maximum bit rate 6.25 Mbps. Single-wire and loop operations. General-Purpose I/O (GPIO) Port * 32 bidirectional signal lines that either serve the peripherals or act as programmable I/O ports. * Each port can be programmed separately to serve up to two dedicated peripherals, and each port supports open-drain output mode. I2C Software Module * Booting from a serial EEPROM. * Uses GPIO timing. Timers Hardware Semaphores Two modules of 16 timers each. * Cyclic or one-shot. * Input clock polarity control. * Interrupt request when counting reaches a programmed threshold. * Pulse or level interrupts. * Dynamically updated programmed threshold. * Read counter any time. Watchdog mode for the timers that connect to the device. Eight coded hardware semaphores, locked by simple write access without need for read-modify-write mechanism. Global Interrupt Controller (GIC) * Consolidation of chip maskable interrupt and non-maskable interrupt sources and routing to INT_OUT, NMI_OUT, and to the cores. * Generation of 32 virtual interrupts (eight to each SC140 core) by a simple write access. * Generation of virtual NMI (one to each SC140 core) by a simple write access. Reduced Power Dissipation * * * * Packaging Real-Time Operating System (RTOS) Low power CMOS design. Separate power supply for internal logic (1.2 V or 1.1 V) and I/O (3.3 V). Low-power standby modes. Optimized power management circuitry (instruction-dependent, peripheral-dependent, and mode-dependent). * 0.8 mm pitch flip-chip plastic ball-grid array (FC-PBGA) with lead-free or lead-bearing spheres. * 431-connection (ball). * 20 mm x 20 mm. The real-time operating system (RTOS) fully supports device architecture (multi-core, memory hierarchy, ICache, timers, DMA controller, interrupts, peripherals), as follows: * High-performance and deterministic, delivering predictive response time. * Optimized to provide low interrupt latency with high data throughput. * Preemptive and priority-based multitasking. * Fully interrupt/event driven. * Small memory footprint. * Comprehensive set of APIs. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor vii Features Feature Description Multi-Core Support * One instance of kernel code in all four SC140 cores. * Dynamic and static memory allocation from local memory (M1) and shared memory (M2). Distributed System Support Enables transparent inter-task communications between tasks running inside the SC140 cores and the other tasks running in on-board devices or remote network devices: * Messaging mechanism between tasks using mailboxes and semaphores. * Networking support; data transfer between tasks running inside and outside the device using networking protocols. * Includes integrated device drivers for such peripherals as TDM, UART, and external buses. Software Support * Task debugging utilities integrated with compilers and vendors. * Board support package (BSP) for the application development system (ADS). * Integrated development environment (IDE): -- C/C++ compiler with in-line assembly so developers can generate highly optimized DSP code. Translates C/C++ code into parallel fetch sets and maintains high code density. -- Librarian. User can create libraries for modularity. -- A collection of C/C++ functions for developer use. -- Highly efficient linker to produce executables from object code. -- Seamlessly integrated real-time, non-intrusive multi-mode debugger for debugging highly optimized DSP algorithms. The developer can choose to debug in source code, assembly code, or mixed mode. -- Device simulation models enable design and simulation before hardware availability. -- Profiler using a patented binary code instrumentation (BCI) technique helps developers identify program design inefficiencies. -- Version control. Metrowerks(R) CodeWarrior(R) includes plug-ins for ClearCase, Visual SourceSafe, and CVS. Boot Options * * * * * External memory. External host. UART. TDM. I2C MSC8122ADS * Host debug through single JTAG connector supports both processors. * MSC8103 as the MSC8122 host with both devices on the board. The MSC8103 system bus connects to the MSC8122 DSI. * Flash memory for stand-alone applications. * Communications ports: -- 10/100Base-T. -- 155 Mbit ATM over Optical. -- T1/E1 TDM interface. -- H.110. -- Voice codec. -- RS-232. -- High-density (MICTOR) logic analyzer connectors to monitor MSC8122 signals -- 6U CompactPCI form factor. * Emulates MSC8122 DSP farm by connecting to three other ADS boards. MSC8122 Technical Data, Rev. 12 viii Freescale Semiconductor Product Documentation Product Documentation The documents listed in Table 1 are required for a complete description of the MSC8122 and are necessary to design properly with the part. Documentation is available from a local Freescale distributor, a Freescale semiconductor sales office, or a Freescale Literature Distribution Center. For documentation updates, visit the Freescale DSP website. See the contact information on the back of this document. Table 1. MSC8122 Documentation Name Description Order Number MSC8122 Technical Data MSC8122 features list and physical, electrical, timing, and package specifications MSC8122 MSC8122 User's Guide User information includes system functionality, getting started, and programming topics Availability TBD MSC8122 Reference Manual Detailed functional description of the MSC8122 memory and peripheral configuration, MSC8122RM operation, and register programming StarCoreTM SC140 DSP Core Reference Manual Detailed description of the SC140 family processor core and instruction set MNSC140CORE Application Notes Documents describing specific applications or optimized device operation including code examples Refer to the MSC8122 product page. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor ix MSC8122 Technical Data, Rev. 12 x Freescale Semiconductor 1 Signals/Connections The MSC8122 external signals are organized into functional groups, as shown in Table 1-1 and Figure 1-1. Table 1-1 lists the functional groups, the number of signal connections in each group, and references the table that gives a detailed listing of multiplexed signals within each group. Figure 1-1 shows MSC8122 external signals organized by function. Table 1-1. MSC8122 Functional Signal Groupings Functional Group Number of Signal Connections Power (VDD, VCC, and GND) Clock Reset and configuration Description 155 Table 1-2 on page 1-3 3 Table 1-3 on page 1-3 4 Table 1-4 on page 1-3 DSI, system bus, Ethernet, and interrupts 210 Table 1-5 on page 1-4 Memory controller 16 Table 1-6 on page 1-14 General-purpose input/output (GPIO), time-division multiplexed (TDM) interface, universal asynchronous receiver/ transmitter (UART), Ethernet, and timers 32 Table 1-7 on page 1-16 Dedicated Ethernet signals 3 Table 1-8 on page 1-23 EOnCE and JTAG test access port 7 Table 1-9 on page 1-24 Reserved (denotes connections that are always reserved) 1 Table 1-10 on page 1-24 MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-1 Signals/Connections HD0/SWTE HD1/DSISYNC HD2/DSI64 HD3/MODCK1 HD4/MODCK2 HD5/CNFGS HD[6-31] HD[32-39]/D[32-39]/reserved HD40/D40/ETHRXD0 HD41/D41/ETHRXD1 HD42/D42/ETHRXD2/reserved HD43/D43/ETHRXD3/reserved HD[44-45]/D[44-45]/reserved HD46/D46/ETHTXD0 HD47/D47/ETHTXD1 HD48/D48/ETHTXD2/reserved HD49/D49/ETHTXD3/reserved HD[50-53]/D[50-53]/reserved HD54/D54/ETHTX_EN HD55/D55/ETHTX_ER/reserved HD56/D56/ETHRX_DV/ETHCRS_DV HD57/D57/ETHRX_ER HD58/D58/ETHMDC HD59/D59/ETHMDIO HD60/D60/ETHCOL/reserved HD[61-63]/D[61-63]/reserved HCID[0-2] HCID3/HA8 HA[11-29] HWBS[0-3]/HDBS[0-3]/HWBE[0-3]/HDBE[0-3] HWBS[4-7]/HDBS[4-7]/HWBE[4-7]/HDBE[4-7]/ PWE[4-7]/PSDDQM[4-7]/PBS[4-7] HRDS/HRW/HRDE HBRST HDST[0-1]/HA[9-10] HCS HBCS HTA HCLKIN GPIO0/CHIP_ID0/IRQ4/ETHTXD0 GPIO1/TIMER0/CHIP_ID1/IRQ5/ETHTXD1 GPIO2/TIMER1/CHIP_ID2/IRQ6 GPIO3/TDM3TSYN/IRQ1/ETHTXD2 GPIO4/TDM3TCLK/IRQ2/ETHTX_ER GPIO5/TDM3TDAT/IRQ3/ETHRXD3 GPIO6/TDM3RSYN/IRQ4/ETHRXD2 GPIO7/TDM3RCLK/IRQ5/ETHTXD3 GPIO8/TDM3RDAT/IRQ6/ETHCOL GPIO9/TDM2TSYN/IRQ7/ETHMDIO GPIO10/TDM2TCLK/IRQ8/ETHRX_DV/ETHCRS_DV/NC GPIO11/TDM2TDAT/IRQ9/ETHRX_ER/ETHTXD GPIO12/TDM2RSYN/IRQ10/ETHRXD1/ETHSYNC GPIO13/TDM2RCLK/IRQ11/ETHMDC GPIO14/TDM2RDAT/IRQ12/ETHRXD0/NC GPIO15/TDM1TSYN/DREQ1 GPIO16/TDM1TCLK/DONE1/DRACK1 GPIO17/TDM1TDAT/DACK1 GPIO18/TDM1RSYN/DREQ2 GPIO19/TDM1RCLK/DACK2 GPIO20/TDM1RDAT GPIO21/TDM0TSYN GPIO22/TDM0TCLK/DONE2/DRACK2 GPIO23/TDM0TDAT/IRQ13 GPIO24/TDM0RSYN/IRQ14 GPIO25/TDM0RCLK/IRQ15 GPIO26/TDM0RDAT GPIO27/URXD/DREQ1 GPIO28/UTXD/DREQ2 GPIO29/CHIP_ID3/ETHTX_EN GPIO30/TIMER2/TMCLK/SDA GPIO31/TIMER3/SCL 1 1 1 1 1 1 26 8 1 1 1 1 2 1 1 1 1 4 1 1 1 1 1 1 1 3 3 1 19 4 4 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D S I / S Y S. B U S / E T H E R N E T S Y S T E M B U S M E M C D S I G P I O / T D M / E T H E R N E T / T I M E R S / I 2 C M E M C S Y S De bug C L K R E S E T J T A G 32 1 1 3 5 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 32 1 1 1 1 1 1 1 1 1 A[0-31] TT0/HA7 TT1 TT[2-4]/CS[5-7] CS[0-4] TSZ[0-3] TBST IRQ1/GBL IRQ3/BADDR31 IRQ2/BADDR30 IRQ5/BADDR29 BADDR28 BADDR27 BR BG DBG ABB/IRQ4 DBB/IRQ5 TS AACK ARTRY D[0-31] reserved/DP0/DREQ1/EXT_BR2 IRQ1/DP1/DACK1/EXT_BG2 IRQ2/DP2/DACK2/EXT_DBG2 IRQ3/DP3/DREQ2/EXT_BR3 IRQ4/DP4/DACK3/EXT_DBG3 IRQ5/DP5/DACK4/EXT_BG3 IRQ6/DP6/DREQ3 IRQ7/DP7/DREQ4 TA 1 1 1 1 1 1 1 3 1 4 1 1 1 1 1 1 TEA NMI NMI_OUT PSDVAL IRQ7/INT_OUT 1 1 1 1 1 1 1 1 1 1 1 1 1 1 EE0 EE1 CLKOUT Reserved CLKIN PORESET HRESET Ded. 1 Eth. 1 Net 1 BCTL0 BCTL1/CS5 BM[0-2]/TC[0-2]/BNKSEL[0-2] ALE PWE[0-3]/PSDDQM[0-3]/PBS[0-3] PSDA10/PGPL0 PSDWE/PGPL1 POE/PSDRAS/PGPL2 PSDCAS/PGPL3 PGTA/PUPMWAIT/PGPL4/PPBS PSDAMUX/PGPL5 SRESET RSTCONF TMS TDI TCK TRST TDO ETHRX_CLK/ETHSYNC_IN ETHTX_CLK/ETHREF_CLK/ETHCLOCK ETHCRS/ETHRXD Power signals are: VDD, VDDH, VCCSYN, GND, GNDH, and GNDSYN. Reserved signals can be left unconnected. NC signals must not be connected. Figure 1-1. MSC8122 External Signals MSC8122 Technical Data, Rev. 12 1-2 Freescale Semiconductor Power Signals 1.1 Power Signals Table 1-2. Power and Ground Signal Inputs Signal Name Description VDD Internal Logic Power VDD dedicated for use with the device core. The voltage should be well-regulated and the input should be provided with an extremely low impedance path to the VDD power rail. VDDH Input/Output Power This source supplies power for the I/O buffers. The user must provide adequate external decoupling capacitors. VCCSYN System PLL Power VCC dedicated for use with the system Phase Lock Loop (PLL). The voltage should be well-regulated and the input should be provided with an extremely low impedance path to the VCC power rail. GND System Ground An isolated ground for the internal processing logic and I/O buffers. This connection must be tied externally to all chip ground connections, except GNDSYN. The user must provide adequate external decoupling capacitors. GNDSYN System PLL Ground Ground dedicated for system PLL use. The connection should be provided with an extremely low-impedance path to ground. 1.2 Clock Signals Table 1-3. Signal Name CLKIN Clock Signals Type Input CLKOUT Output Reserved Input Signal Description Clock In Primary clock input to the MSC8122 PLL. Clock Out The bus clock. Reserved. Pull down to ground. 1.3 Reset and Configuration Signals Table 1-4. Signal Name Type Reset and Configuration Signals Signal Description PORESET Input Power-On Reset When asserted, this line causes the MSC8122 to enter power-on reset state. RSTCONF Input Reset Configuration Used during reset configuration sequence of the chip. A detailed explanation of its function is provided in the MSC8122 Reference Manual. This signal is sampled upon deassertion of PORESET. Note: When PORESET is deasserted, the MSC8122 also samples the following signals: * BM[0-2]--Selects the boot mode. * MODCK[1-2]--Selects the clock configuration. * SWTE--Enables the software watchdog timer. * DSISYNC, DSI64, CNFGS, and CHIP_ID[0-3]--Configures the DSI. Refer to Table 1-5 for details on these signals. HRESET Input/Output Hard Reset When asserted as an input, this signal causes the MSC8122 to enter hard reset state. After the device enters a hard reset state, it drives the signal as an open-drain output. SRESET Input/Output Soft Reset When asserted as an input, this signal causes the MSC8122 to enter soft reset state. After the device enters a soft reset state, it drives the signal as an open-drain output. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-3 Signals/Connections 1.4 Direct Slave Interface, System Bus, Ethernet, and Interrupt Signals The direct slave interface (DSI) is combined with the system bus because they share some common signal lines. Individual assignment of a signal to a specific signal line is configured through internal registers. Table 1-5 describes the signals in this group. Note: Although there are fifteen interrupt request (IRQ) connections to the core processors, there are multiple external lines that can connect to these internal signal lines. After reset, the default configuration enables only IRQ[1-7], but includes two input lines each for IRQ[1-3] and IRQ7. The designer must select one line for each required interrupt and reconfigure the other external signal line or lines for alternate functions. Additional alternate IRQ lines and IRQ[8-15] are enabled through the GPIO signal lines. Table 1-5. Signal Name HD0 SWTE HD1 DSISYNC HD2 DSI64 HD3 MODCK1 HD4 MODCK2 HD5 CNFGS HD[6-31] DSI, System Bus, Ethernet, and Interrupt Signals Type Description Input/ Output Host Data Bus 0 Bit 0 of the DSI data bus. Input Software Watchdog Timer Disable. It is sampled on the rising edge of PORESET signal. Input/ Output Host Data Bus 1 Bit 1 of the DSI data bus. Input DSI Synchronous Distinguishes between synchronous and asynchronous operation of the DSI. It is sampled on the rising edge of PORESET signal. Input/ Output Host Data Bus 2 Bit 2 of the DSI data bus. Input DSI 64 Defines the width of the DSI and SYSTEM Data buses. It is sampled on the rising edge of PORESET signal. Input/ Output Host Data Bus 3 Bit 3 of the DSI data bus. Input Clock Mode 1 Defines the clock frequencies. It is sampled on the rising edge of PORESET signal. Input/ Output Host Data Bus 4 Bit 4 of the DSI data bus. Input Clock Mode 2 Defines the clock frequencies. It is sampled on the rising edge of PORESET signal. Input/ Output Host Data Bus 5 Bit 5 of the DSI data bus. Input Configuration Source One signal out of two that indicates reset configuration mode. It is sampled on the rising edge of PORESET signal. Input/ Output Host Data Bus 6-31 Bits 6-31 of the DSI data bus. MSC8122 Technical Data, Rev. 12 1-4 Freescale Semiconductor Direct Slave Interface, System Bus, Ethernet, and Interrupt Signals Table 1-5. Signal Name DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Type Description HD[32-39] Input/ Output Host Data Bus 32-39 Bits 32-39 of the DSI data bus. D[32-39] Input/ Output System Bus Data 32-39 For write transactions, the bus master drives valid data on this bus. For read transactions, the slave drives valid data on this bus. Reserved Input If the Ethernet port is enabled and multiplexed with the DSI/System bus, these pins are reserved and can be left unconnected. HD40 Input/ Output Host Data Bus 40 Bit 40 of the DSI data bus. D40 Input/ Output System Bus Data 40 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHRXD0 Input Ethernet Receive Data 0 In MII and RMII modes, bit 0 of the Ethernet receive data. HD41 Input/ Output Host Data Bus 41 Bit 41 of the DSI data bus. D41 Input/ Output System Bus Data 41 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHRXD1 Input Ethernet Receive Data 1 In MII and RMII modes, bit 1 of the Ethernet receive data. HD42 Input/ Output Host Data Bus 42 Bit 42 of the DSI data bus. D42 Input/ Output System Bus Data 42 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHRXD2 Reserved Input Ethernet Receive Data 2 In MII mode only, bit 2 of the Ethernet receive data. Input In RMII mode, this pin is reserved and can be left unconnected. HD43 Input/ Output Host Data Bus 43 Bit 43 of the DSI data bus. D43 Input/ Output System Bus Data 43 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHRXD3 Input Ethernet Receive Data 3 In MII mode only, bit 3 of the Ethernet receive data. Reserved Input In RMII mode, this pin is reserved and can be left unconnected. HD[44-45] Input/ Output Host Data Bus 44-45 Bits 44-45 of the DSI data bus. D[44-56] Input/ Output System Bus Data 44-45 For write transactions, the bus master drives valid data on this bus. For read transactions, the slave drives valid data on this bus. Reserved Input If the Ethernet port is enabled and multiplexed with the DSI/System bus, these pins are reserved and can be left unconnected. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-5 Signals/Connections Table 1-5. Signal Name DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Type Description HD46 Input/ Output Host Data Bus 46 Bit 46 of the DSI data bus. D46 Input/ Output System Bus Data 46 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHTXD0 Output Ethernet Transmit Data 0 In MII and RMII modes, bit 0 of the Ethernet transmit data. HD47 Input/ Output Host Data Bus 47 Bit 47 of the DSI data bus. D47 Input/ Output System Bus Data 47 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHTXD1 Output Ethernet Transmit Data 1 In MII and RMII modes, bit 1 of the Ethernet transmit data. HD48 Input/ Output Host Data Bus 48 Bit 48 of the DSI data bus. D48 Input/ Output System Bus Data 48 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHTXD2 Output Reserved Input Ethernet Transmit Data 2 In MII mode only, bit 2 of the Ethernet transmit data. In RMII mode, this pin is reserved and can be left unconnected. HD49 Input/ Output Host Data Bus 49 Bit 49 of the DSI data bus. D49 Input/ Output System Bus Data 49 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHTXD3 Reserved Output Input Ethernet Transmit Data 3 In MII mode only, bit 3 of the Ethernet transmit data. In RMII mode, this pin is reserved and can be left unconnected. HD[50-53] Input/ Output Host Data Bus 50-53 Bits 50-53 of the DSI data bus. D[50-53] Input/ Output System Bus Data 50-53 For write transactions, the bus master drives valid data on this bus. For read transactions, the slave drives valid data on this bus. Reserved Input If the Ethernet port is enabled and multiplexed with the DSI/System bus, these pins are reserved and can be left unconnected. HD54 Input/ Output Host Data Bus 54 Bit 54 of the DSI data bus. D54 Input/ Output System Bus Data 54 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHTX_EN Output Ethernet Transmit Data Enable In MII and RMII modes, indicates that the transmit data is valid. MSC8122 Technical Data, Rev. 12 1-6 Freescale Semiconductor Direct Slave Interface, System Bus, Ethernet, and Interrupt Signals Table 1-5. Signal Name DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Type Description HD55 Input/ Output Host Data Bus 55 Bit 55 of the DSI data bus. D55 Input/ Output System Bus Data 55 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHTX_ER Reserved Output Input Ethernet Transmit Data Error In MII mode only, indicates a transmit data error. In RMII mode, this pin is reserved and can be left unconnected. HD56 Input/ Output Host Data Bus 56 Bit 56 of the DSI data bus. D56 Input/ Output System Bus Data 56 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHRX_DV Input Ethernet Receive Data Valid Indicates that the receive data is valid. ETHCRS_DV Input Ethernet Carrier Sense/Receive Data Valid In RMII mode, indicates that a carrier is detected and after the connection is established that the receive data is valid. HD57 Input/ Output Host Data Bus 57 Bit 57 of the DSI data bus. D57 Input/ Output System Bus Data 57 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHRX_ER Input Ethernet Receive Data Error In MII and RMII modes, indicates a receive data error. HD58 Input/ Output Host Data Bus 58 Bit 58 of the DSI data bus. D58 Input/ Output System Bus Data 58 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHMDC Output Ethernet Management Clock In MII and RMII modes, used for the MDIO reference clock. HD59 Input/ Output Host Data Bus 59 Bit 59 of the DSI data bus. D59 Input/ Output System Bus Data 59 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHMDIO Input/ Output Ethernet Management Data In MII and RMII modes, used for station management data input/output. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-7 Signals/Connections Table 1-5. Signal Name DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Type Description HD60 Input/ Output Host Data Bus 60 Bit 60 of the DSI data bus. D60 Input/ Output System Bus Data 60 For write transactions, the bus master drives valid data on this line. For read transactions, the slave drives valid data on this bus. ETHCOL Input/ Output Ethernet Collision In MII mode only, indicates that a collision was detected. Reserved Input In RMII mode, this pin is reserved and can be left unconnected. HD[61-63] Input/ Output Host Data Bus 61-63 Bits 61-63 of the DSI data bus. D[61-63] Input/ Output System Bus Data 61-63 For write transactions, the bus master drives valid data on this bus. For read transactions, the slave drives valid data on this bus. Reserved Input If the Ethernet port is enabled and multiplexed with the DSI/System bus, these pins are reserved and can be left unconnected. HCID[0-2] Input Host Chip ID 0-2 With HCID3, carries the chip ID of the DSI. The DSI is accessed only if HCS is asserted and HCID[0-3] matches the Chip_ID, or if HBCS is asserted. HCID3 Input Host Chip ID 3 With HCI[0-2], carries the chip ID of the DSI. The DSI is accessed only if HCS is asserted and HCID[0-3] matches the Chip_ID, or if HBCS is asserted. HA8 Input Host Bus Address 8 Used by an external host to access the internal address space. HA[11-29] Input Host Bus Address 11-29 Used by external host to access the internal address space. HWBS[0-3] Input Host Write Byte Strobes (In Asynchronous dual mode) One bit per byte is used as a strobe for host write accesses. HDBS[0-3] Input Host Data Byte Strobe (in Asynchronous single mode) One bit per byte is used as a strobe for host read or write accesses HWBE[0-3] Input Host Write Byte Enable (In Synchronous dual mode) One bit per byte is used to indicate a valid data byte for host read or write accesses. HDBE[0-3] Input Host Data Byte Enable (in Synchronous single mode) One bit per byte is used as a strobe enable for host write accesses MSC8122 Technical Data, Rev. 12 1-8 Freescale Semiconductor Direct Slave Interface, System Bus, Ethernet, and Interrupt Signals Table 1-5. Signal Name DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Type Description HWBS[4-7] Input Host Write Byte Strobes (In Asynchronous dual mode) One bit per byte is used as a strobe for host write accesses. HDBS[4-7] Input Host Data Byte Strobe (in Asynchronous single mode) One bit per byte is used as a strobe for host read or write accesses HWBE[4-7] Input Host Write Byte Enable (In Synchronous dual mode) One bit per byte is used to indicate a valid data byte for host write accesses. HDBE[4-7] Input Host Data Byte Enable (in Synchronous single mode) One bit per byte is used as a strobe enable for host read or write accesses PWE[4-7] Output System Bus Write Enable Outputs of the bus general-purpose chip-select machine (GPCM). These pins select byte lanes for write operations. PSDDQM[4-7] Output System Bus SDRAM DQM From the SDRAM control machine. These pins select specific byte lanes of SDRAM devices. PBS[4-7] Output System Bus UPM Byte Select From the UPM in the memory controller, these signals select specific byte lanes during memory operations. The timing of these pins is programmed in the UPM. The actual driven value depends on the address and size of the transaction and the port size of the accessed device. HRDS Input Host Read Data Strobe (In Asynchronous dual mode) Used as a strobe for host read accesses. HRW Input Host Read/Write Select (in Asynchronous/Synchronous single mode) Host read/write select. HRDE Input Host Read Data Enable (In Synchronous dual mode) Indicates valid data for host read accesses. HBRST Input Host Burst The host asserts this pin to indicate that the current transaction is a burst transaction in synchronous mode only. HDST[0-1] Input Host Data Structure 0-1 Defines the data structure of the host access in DSI little-endian mode. HA[9-10] Host Bus Address 9-10 Used by an external host to access the internal address space. HCS Input Host Chip Select DSI chip select. The DSI is accessed only if HCS is asserted and HCID[0-3] matches the Chip_ID. HBCS Input Host Broadcast Chip Select DSI chip select for broadcast mode. Enables more than one DSI to share the same host chip-select pin for broadcast write accesses. HTA HCLKIN Output Input Host Transfer Acknowledge Upon a read access, indicates to the host when the data on the data bus is valid. Upon a write access, indicates to the host that the data on the data bus was written to the DSI write buffer. Host Clock Input Host clock signal for DSI synchronous mode. A[0-31] Input/ Output Address Bus When the MSC8122 is in external master bus mode, these pins function as the system address bus. The MSC8122 drives the address of its internal bus masters and responds to addresses generated by external bus masters. When the MSC8122 is in internal master bus mode, these pins are used as address lines connected to memory devices and are controlled by the MSC8122 memory controller. TT0 Input/ Output Bus Transfer Type 0 The bus master drives this pins during the address tenure to specify the type of the transaction. HA7 Host Bus Address 7 Used by an external host to access the internal address space. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-9 Signals/Connections Table 1-5. Signal Name Type DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Description TT1 Input/ Output Bus Transfer Type 1 The bus master drives this pins during the address tenure to specify the type of the transaction. Some applications use only the TT1 signal, for example, from MSC8122 to MSC8122 or MSC8122 to MSC8101 and vice versa. In these applications, TT1 functions as read/write signal. TT[2-4] Input/ Output Bus Transfer Type 2-4 The bus master drives these pins during the address tenure to specify the type of the transaction. CS[5-7] Output Chip Select 5-7 Enables specific memory devices or peripherals connected to the system bus. CS[0-4] Output Chip Select 0-4 Enables specific memory devices or peripherals connected to the system bus. TSZ[0-3] Input/ Output Transfer Size 0-3 The bus master drives these pins with a value indicating the number of bytes transferred in the current transaction. TBST Input/ Output Bus Transfer Burst The bus master asserts this pin to indicate that the current transaction is a burst transaction (transfers eight words). IRQ1 Input GBL Output IRQ3 Input BADDR31 IRQ2 BADDR30 IRQ5 Output Input Output Input Interrupt Request 11 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Global1 When a master within the MSC8122 initiates a bus transaction, it drives this pin. Assertion of this pin indicates that the transfer is global and should be snooped by caches in the system. Interrupt Request 31 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Burst Address 311 Five burst address output pins are outputs of the memory controller. These pins connect directly to burstable memory devices without internal address incrementors controlled by the MSC8122 memory controller. Interrupt Request 21 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Burst Address 301 Five burst address output pins are outputs of the memory controller. These pins connect directly to burstable memory devices without internal address incrementors controlled by the MSC8122 memory controller. Interrupt Request 51 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. BADDR29 Output Bus Burst Address 291 Five burst address output pins are outputs of the memory controller. These pins connect directly to burstable memory devices without internal address incrementors controlled by the MSC8122 memory controller. BADDR28 Output Burst Address 28 Five burst address output pins are outputs of the memory controller. These pins connect directly to burstable memory devices without internal address incrementors controlled by the MSC8122 memory controller. BADDR27 Output Burst Address 27 Five burst address output pins are outputs of the memory controller. These pins connect directly to burstable memory devices without internal address incrementors controlled by the MSC8122 memory controller. MSC8122 Technical Data, Rev. 12 1-10 Freescale Semiconductor Direct Slave Interface, System Bus, Ethernet, and Interrupt Signals Table 1-5. Signal Name DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Type Description Request2 BR Input/ Output Bus When an external arbiter is used, the MSC8122 asserts this pin as an output to request ownership of the bus. When the MSC8122 controller is used as an internal arbiter, an external master asserts this pin as an input to request bus ownership. BG Input/ Output Bus Grant2 When the MSC8122 acts as an internal arbiter, it asserts this pin as an output to grant bus ownership to an external bus master. When an external arbiter is used, it asserts this pin as an input to grant bus ownership to the MSC8122. DBG Input/ Output Data Bus Grant2 When the MSC8122 acts as an internal arbiter, it asserts this pin as an output to grant data bus ownership to an external bus master. When an external arbiter is used, it asserts this pin as an input to grant data bus ownership to the MSC8122. ABB Input/ Output Address Bus Busy1 The MSC8122 asserts this pin as an output for the duration of the address bus tenure. Following an AACK, which terminates the address bus tenure, the MSC8122 deasserts ABB for a fraction of a bus cycle and then stops driving this pin. The MSC8122 does not assume bus ownership as long as it senses this pin is asserted as an input by an external bus master. IRQ4 DBB IRQ5 Input Interrupt Request 4 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Input/ Output Data Bus Busy1 The MSC8122 asserts this pin as an output for the duration of the data bus tenure. Following a TA, which terminates the data bus tenure, the MSC8122 deasserts DBB for a fraction of a bus cycle and then stops driving this pin. The MSC8122 does not assume data bus ownership as long as it senses that this pin is asserted as an input by an external bus master. Input Interrupt Request 5 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. TS Input/ Output Bus Transfer Start Assertion of this pin signals the beginning of a new address bus tenure. The MSC8122 asserts this signal when one of its internal bus masters begins an address tenure. When the MSC8122 senses that this pin is asserted by an external bus master, it responds to the address bus tenure as required (snoop if enabled, access internal MSC8122 resources, memory controller support). AACK Input/ Output Address Acknowledge A bus slave asserts this signal to indicate that it has identified the address tenure. Assertion of this signal terminates the address tenure. ARTRY Input/ Output Address Retry Assertion of this signal indicates that the bus master should retry the bus transaction. An external master asserts this signal to enforce data coherency with its caches and to prevent deadlock situations. D[0-31] Input/ Output Data Bus Bits 0-31 In write transactions, the bus master drives the valid data on this bus. In read transactions, the slave drives the valid data on this bus. Reserved DP0 Input The primary configuration selection (default after reset) is reserved. Input/ Output System Bus Data Parity 0 The agent that drives the data bus also drives the data parity signals. The value driven on the data parity 0 pin should give odd parity (odd number of ones) on the group of signals that includes data parity 0 and D[0-7]. DREQ1 Input DMA Request 1 Used by an external peripheral to request DMA service. EXT_BR2 Input External Bus Request 2 An external master asserts this pin to request bus ownership from the internal arbiter. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-11 Signals/Connections Table 1-5. Signal Name IRQ1 DP1 DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Type Description Input Interrupt Request 1 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Input/ Output System Bus Data Parity 1 The agent that drives the data bus also drives the data parity signals. The value driven on the data parity 1 pin should give odd parity (odd number of ones) on the group of signals that includes data parity 1 and D[8-15]. DACK1 Output DMA Acknowledge 1 The DMA controller drives this output to acknowledge the DMA transaction on the bus. EXT_BG2 Output External Bus Grant 22 The MSC8122 asserts this pin to grant bus ownership to an external bus master. IRQ2 DP2 Input Interrupt Request 2 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Input/ Output System Bus Data Parity 2 The agent that drives the data bus also drives the data parity signals. The value driven on the data parity 2 pin should give odd parity (odd number of ones) on the group of signals that includes data parity 2 and D[16-23]. DACK2 Output DMA Acknowledge 2 The DMA controller drives this output to acknowledge the DMA transaction on the bus. EXT_DBG2 Output External Data Bus Grant 22 The MSC8122 asserts this pin to grant data bus ownership to an external bus master. IRQ3 DP3 Input Interrupt Request 3 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Input/ Output System Bus Data Parity 3 The agent that drives the data bus also drives the data parity signals. The value driven on the data parity 3 pin should give odd parity (odd number of ones) on the group of signals that includes data parity 3 and D[24-31]. DREQ2 Input DMA Request 2 Used by an external peripheral to request DMA service. EXT_BR3 Input External Bus Request 32 An external master should assert this pin to request bus ownership from the internal arbiter. IRQ4 Input Interrupt Request 4 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. DP4 Input/ Output System Bus Data Parity 4 The agent that drives the data bus also drives the data parity signals. The value driven on the data parity 4 pin should give odd parity (odd number of ones) on the group of signals that includes data parity 4 and D[32-39]. DACK3 Output DMA Acknowledge 3 The DMA controller drives this output to acknowledge the DMA transaction on the bus. EXT_DBG3 Output External Data Bus Grant 32 The MSC8122 asserts this pin to grant data bus ownership to an external bus master. MSC8122 Technical Data, Rev. 12 1-12 Freescale Semiconductor Direct Slave Interface, System Bus, Ethernet, and Interrupt Signals Table 1-5. Signal Name IRQ5 DP5 DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Type Description Input Interrupt Request 5 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Input/ Output System Bus Data Parity 5 The agent that drives the data bus also drives the data parity signals. The value driven on the data parity 5 pin should give odd parity (odd number of ones) on the group of signals that includes data parity 5 and D[40-47]. DACK4 Output DMA Acknowledge 4 The DMA controller drives this output to acknowledge the DMA transaction on the bus. EXT_BG3 Output External Bus Grant 32 The MSC8122 asserts this pin to grant bus ownership to an external bus. IRQ6 DP6 Input Interrupt Request 6 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Input/ Output System Bus Data Parity 6 The agent that drives the data bus also drives the data parity signals. The value driven on the data parity 6 pin should give odd parity (odd number of ones) on the group of signals that includes data parity 6 and D[48-55]. DREQ3 Input DMA Request 3 Used by an external peripheral to request DMA service. IRQ7 Input Interrupt Request 7 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. DP7 DREQ4 Input/ Output System Bus Data Parity 7 The agent that drives the data bus also drives the data parity signals. The value driven on the data parity 7 pin should give odd parity (odd number of ones) on the group of signals that includes data parity 7 and D[56-63]. Input DMA Request 4 Used by an external peripheral to request DMA service. TA Input/ Output Transfer Acknowledge Indicates that a data beat is valid on the data bus. For single-beat transfers, TA assertion indicates the termination of the transfer. For burst transfers, TA is asserted eight times to indicate the transfer of eight data beats, with the last assertion indicating the termination of the burst transfer. TEA Input/ Output Transfer Error Acknowledge Indicates a failure of the data tenure transaction.The masters within the MSC8122 monitor the state of this pin. The MSC8122 internal bus monitor can assert this pin if it identifies a bus transfer that does not complete. NMI NMI_OUT PSDVAL Input Non-Maskable Interrupt When an external device asserts this line, it generates an non-maskable interrupt in the MSC8122, which is processed internally (default) or is directed to an external host for processing (see NMI_OUT). Output Non-Maskable Interrupt Output An open-drain pin driven from the MSC8122 internal interrupt controller. Assertion of this output indicates that a non-maskable interrupt is pending in the MSC8122 internal interrupt controller, waiting to be handled by an external host. Input/ Output Port Size Data Valid Indicates that a data beat is valid on the data bus. The difference between the TA pin and the PSDVAL pin is that the TA pin is asserted to indicate data transfer terminations, while the PSDVAL signal is asserted with each data beat movement. When TA is asserted, PSDVAL is always asserted. However, when PSDVAL is asserted, TA is not necessarily asserted. For example, if the DMA controller initiates a double word (2 x 64 bits) transaction to a memory device with a 32-bit port size, PSDVAL is asserted three times without TA and, finally, both pins are asserted to terminate the transfer. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-13 Signals/Connections Table 1-5. Signal Name IRQ7 INT_OUT Notes: 1. 2. DSI, System Bus, Ethernet, and Interrupt Signals (Continued) Type Description Input Interrupt Request 7 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Output Interrupt Output Assertion of this output indicates that an unmasked interrupt is pending in the MSC8122 internal interrupt controller. See the System Interface Unit (SIU) chapter in the MSC8122 Reference Manual for details on how to configure these pins. When used as the bus control arbiter, the MSC8122 can support up to three external bus masters. Each master uses its own set of Bus Request, Bus Grant, and Data Bus Grant signals (BR/BG/DBG, EXT_BR2/EXT_BG2/EXT_DBG2, and EXT_BR3/EXT_BG3/EXT_DBG3). Each of these signal sets must be configured to indicate whether the external master is or is not a MSC8122 master device. See the Bus Configuration Register (BCR) description in the System Interface Unit (SIU) chapter in the MSC8122 Reference Manual for details on how to configure these pins. The second and third set of pins is defined by EXT_xxx to indicate that they can only be used with external master devices. The first set of pins (BR/BG/DBG) have a dual function. When the MSC8122 is not the bus arbiter, it uses these signals (BR/BG/DBG) to obtain master control of the bus. 1.5 Memory Controller Signals Refer to the Memory Controller chapter in the MSC8122 Reference Manual for details on configuring these signals. Table 1-6. Signal Name Memory Controller Signals Type Description BCTL0 Output System Bus Buffer Control 0 Controls buffers on the data bus. Usually used with BCTL1. The exact function of this pin is defined by the value of SIUMCR[BCTLC]. BCTL1 Output System Bus Buffer Control 1 Controls buffers on the data bus. Usually used with BCTL0. The exact function of this pin is defined by the value of SIUMCR[BCTLC]. CS5 Output System and Local Bus Chip Select 5 Enables specific memory devices or peripherals connected to MSC8122 buses. BM[0-2] TC[0-2] Input Boot Mode 0-2 Defines the boot mode of the MSC8122. This signal is sampled on PORESET deassertion. Input/ Output Transfer Code 0-2 The bus master drives these pins during the address tenure to specify the type of the code. BNKSEL[0-2] Output Bank Select 0-2 Selects the SDRAM bank when the MSC8122 is in 60x-compatible bus mode. ALE Output Address Latch Enable Controls the external address latch used in an external master bus. PWE[0-3] Output System Bus Write Enable Outputs of the bus general-purpose chip-select machine (GPCM). These pins select byte lanes for write operations. PSDDQM[0-3] Output System Bus SDRAM DQM From the SDRAM control machine. These pins select specific byte lanes of SDRAM devices. PBS[0-3] Output System Bus UPM Byte Select From the UPM in the memory controller, these signals select specific byte lanes during memory operations. The timing of these pins is programmed in the UPM. The actual driven value depends on the address and size of the transaction and the port size of the accessed device. MSC8122 Technical Data, Rev. 12 1-14 Freescale Semiconductor Memory Controller Signals Table 1-6. Signal Name Memory Controller Signals (Continued) Type Description PSDA10 Output System Bus SDRAM A10 From the bus SDRAM controller. The precharge command defines which bank is precharged. When the row address is driven, it is a part of the row address. When column address is driven, it is a part of column address. PGPL0 Output System Bus UPM General-Purpose Line 0 One of six general-purpose output lines from the UPM. The values and timing of this pin are programmed in the UPM. PSDWE Output System Bus SDRAM Write Enable From the bus SDRAM controller. Should connect to SDRAM WE input. PGPL1 Output System Bus UPM General-Purpose Line 1 One of six general-purpose output lines from the UPM. The values and timing of this pin are programmed in the UPM. POE Output System Bus Output Enable From the bus GPCM. Controls the output buffer of memory devices during read operations. PSDRAS Output System Bus SDRAM RAS From the bus SDRAM controller. Should connect to SDRAM RAS input. PGPL2 Output System Bus UPM General-Purpose Line 2 One of six general-purpose output lines from the UPM. The values and timing of this pin are programmed in the UPM. PSDCAS Output System Bus SDRAM CAS From the bus SDRAM controller. Should connect to SDRAM CAS input. PGPL3 Output System Bus UPM General-Purpose Line 3 One of six general-purpose output lines from the UPM. The values and timing of this pin are programmed in the UPM. PGTA Input System GPCM TA Terminates external transactions during GPCM operation. Requires an external pull-up resistor for proper operation. PUPMWAIT Input System Bus UPM Wait An external device holds this pin low to force the UPM to wait until the device is ready to continue the operation. PGPL4 Output System Bus UPM General-Purpose Line 4 One of six general-purpose output lines from the UPM. The values and timing of this pin are programmed in the UPM. PPBS Output System Bus Parity Byte Select In systems that store data parity in a separate chip, this output is used as the byte-select for that chip. PSDAMUX Output System Bus SDRAM Address Multiplexer Controls the system bus SDRAM address multiplexer when the MSC8122 is in external master mode. PGPL5 Output System Bus UPM General-Purpose Line 5 One of six general-purpose output lines from the UPM. The values and timing of this pin are programmed in the UPM. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-15 Signals/Connections 1.6 GPIO, TDM, UART, and Timer Signals The general-purpose input/output (GPIO), time-division multiplexed (TDM), universal asynchronous receiver/transmitter (UART), and timer signals are grouped together because they use a common set of signal lines. Individual assignment of a signal to a specific signal line is configured through internal registers. Table 1-7 describes the signals in this group. Table 1-7. Signal Name GPIO0 Type GPIO, TDM, UART, Ethernet, and Timer Signals Description Input/ Output General-Purpose Input Output 0 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. CHIP_ID0 Input Chip ID 0 Determines the chip ID of the MSC8122 DSI. It is sampled on the rising edge of PORESET signal. IRQ4 Input Interrupt Request 4 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHTXD0 GPIO1 TIMER0 Output Ethernet Transmit Data 0 For MII or RMII mode, bit 0 of the Ethernet transmit data. Input/ Output General-Purpose Input Output 1 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. Input/ Output Timer 0 Each signal is configured as either input to or output from the counter. See the MSC8122 Reference Manual for configuration details. CHIP_ID1 Input Chip ID 1 Determines the chip ID of the MSC8122 DSI. It is sampled on the rising edge of PORESET signal. IRQ5 Input Interrupt Request 5 One of the fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHTXD1 Output Ethernet Transmit Data 1 For MII or RMII mode, bit 1 of the Ethernet transmit data. GPIO2 Input/ Output General-Purpose Input Output 2 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual. TIMER1 Input/ Output Timer 1 Each signal is configured as either input to or output from the counter. For the configuration of the pin direction, refer to the MSC8122 Reference Manual. CHIP_ID2 Input Chip ID 2 Determines the chip ID of the MSC8122 DSI. It is sampled on the rising edge of PORESET signal. IRQ6 Input Interrupt Request 6 One of the fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. MSC8122 Technical Data, Rev. 12 1-16 Freescale Semiconductor GPIO, TDM, UART, and Timer Signals Table 1-7. Signal Name GPIO, TDM, UART, Ethernet, and Timer Signals (Continued) Type Description GPIO3 Input/ Output General-Purpose Input Output 3 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM3TSYN Input/ Output TDM3 Transmit Frame Sync Transmit frame sync for TDM 3. IRQ1 ETHTXD2 GPIO4 Input Output Interrupt Request 1 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Ethernet Transmit Data 2 For MII mode only, bit 2 of the Ethernet transmit data. Input/ Output General-Purpose Input Output 4 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM3TCLK Input TDM3 Transmit Clock Transmit Clock for TDM 3 IRQ2 Input Interrupt Request 2 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHTX_ER Output Ethernet Transmit Data Error For MII mode only, indicates whether a transmit data error occurred. GPIO5 Input/ Output General-Purpose Input/Output 5 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM3TDAT Input/ Output TDM3 Serial Transmitter Data The serial transmit data signal for TDM 3. As an output, it provides the DATA_D signal for TDM 3. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ3 Input Interrupt Request 3 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHRXD3 Input Ethernet Receive Data 3 For MII mode only, bit 3 of the Ethernet receive data. GPIO6 Input/ Output General-Purpose Input Output 6 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM3RSYN Input/ Output TDM3 Receive Frame Sync The receive sync signal for TDM 3. As an input, this can be the DATA_B data signal for TDM 3.For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ4 Input Interrupt Request 4 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHRXD2 Input Ethernet Receive Data 2 For MII mode only, bit 2 of the Ethernet receive data. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-17 Signals/Connections Table 1-7. Signal Name GPIO, TDM, UART, Ethernet, and Timer Signals (Continued) Type Description GPIO7 Input/ Output General-Purpose Input Output 7 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM3RCLK Input/ Output TDM3 Receive Clock The receive clock signal for TDM 3. As an output, this can be the DATA_C data signal for TDM 3. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ5 ETHTXD3 Input Output Interrupt Request 5 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Ethernet Transmit Data 3 For MII mode only, bit 3 of the Ethernet transmit data. GPIO8 Input/ Output General-Purpose Input Output 8 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM3RDAT Input/ Output TDM3 Serial Receiver Data The receive data signal for TDM 3. As an input, this can be the DATA_A data signal for TDM 3. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ6 Input Interrupt Request 6 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHCOL Input Ethernet Collision For MII mode only, indicates whether a collision was detected. GPIO9 Input/ Output General-Purpose Input Output 9 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM2TSYN Input/ Output TDM2 Transmit frame Sync Transmit Frame Sync for TDM 2. IRQ7 Input Interrupt Request 7 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHMDIO Input/ Output Ethernet Management Data Station management data input/output line in MII, RMII, and SMII modes. GPIO10 Input/ Output General-Purpose Input Output 10 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM2TCLK Input TDM 2 Transmit Clock Transmit Clock for TDM 2. IRQ8 Input Interrupt Request 8 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHRX_DV Input Ethernet Receive Data Valid In MII mode, this signal indicates that the receive data is valid. ETHCRS_DV Input Ethernet Carrier Sense/Receive Data Valid In RMII mode, this signal indicates that a carrier is sense or that the receive data is valid. NC Input Not Connected For SMII mode, this signal must be left unconnected. MSC8122 Technical Data, Rev. 12 1-18 Freescale Semiconductor GPIO, TDM, UART, and Timer Signals Table 1-7. Signal Name Type GPIO, TDM, UART, Ethernet, and Timer Signals (Continued) Description GPIO11 Input/ Output General-Purpose Input Output 11 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM2TDAT Input/ Output TDM2 Serial Transmitter Data The transmit data signal for TDM 2. As an output, this can be the DATA_D data signal for TDM 2. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ9 Input Interrupt Request 9 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHRX_ER Input Ethernet Receive Data Error In MII and RMII modes, indicates a receive data error. ETHTXD Output Ethernet Transmit Data In SMII, used as the Ethernet transmit data line. GPIO12 Input/ Output General-Purpose Input Output 12 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM2RSYN Input/ Output TDM2 Receive Frame Sync The receive sync signal for TDM 2. As an input, this can be the DATA_B data signal for TDM 2. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ10 Input Interrupt Request 10 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHRXD1 Input Ethernet Receive Data 1 Bit 1 of the Ethernet receive data (MII and RMII mode). ETHSYNC Output Ethernet Sync Signal In SMII mode, this is the Ethernet sync signal input. GPIO13 Input/ Output General-Purpose Input Output 13 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM2RCLK Input/ Output TDM2 Receive Clock The receive clock signal for TDM 2. As an input, this can be the DATA_C data signal for TDM 2. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ11 ETHMDC Input Output Interrupt Request 11 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. Ethernet Management Clock Used for the MDIO reference clock for MII, RMII, and SMII modes. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-19 Signals/Connections Table 1-7. Signal Name GPIO, TDM, UART, Ethernet, and Timer Signals (Continued) Type Description GPIO14 Input/ Output General-Purpose Input Output 14 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM2RDAT Input/ Output TDM2 Serial Receiver Data The receive data signal for TDM 2. As an input, this can be the DATA_A data signal for TDM 2. For Input configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ12 Input Interrupt Request 12 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. ETHRXD0 Input Ethernet Receive Data 0 Bit 0 of the Ethernet receive data (MII and RMII). NC Input Not Connected For SMII mode, this signal must be left unconnected. GPIO15 Input/ Output General-Purpose Input Output 15 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM1TSYN Input/ Output TDM1 Transmit frame Sync Transmit Frame Sync for TDM 1. DREQ1 GPIO16 TDM1TCLK DONE1 Input DMA Request 1 Used by an external peripheral to request DMA service. Input/ Output General-Purpose Input Output 16 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. Input TDM1 Transmit Clock Transmit Clock for TDM 1. Input/ Output DMA Done 1 Signifies that the channel must be terminated. If the DMA controller generates DONE, the channel handling this peripheral is inactive. As an input to the DMA controller, DONE closes the channel much like a normal channel closing. See the MSC8122 Reference Manual chapters on DMA controller and GPIO for information on configuring the DRACK or DONE mode and pin direction. DRACK1 Output DMA Data Request Acknowledge 1 Asserted by the DMA controller to indicate that the DMA controller has sampled the peripheral request. GPIO17 Input/ Output General-Purpose Input Output 17 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM1TDAT Input/ Output TDM1 Serial Transmitter Data The transmit data signal for TDM 1. As an output, this can be the DATA_D data signal for TDM 1.For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. DACK1 Output DMA Acknowledge 1 The DMA controller drives this output to acknowledge the DMA transaction on the bus. MSC8122 Technical Data, Rev. 12 1-20 Freescale Semiconductor GPIO, TDM, UART, and Timer Signals Table 1-7. Signal Name GPIO, TDM, UART, Ethernet, and Timer Signals (Continued) Type Description GPIO18 Input/ Output General-Purpose Input Output 18 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM1RSYN Input/ Output TDM1 Receive Frame Sync The receive sync signal for TDM 1. As an input, this can be the DATA_B data signal for TDM 1. For configuration details, refer to the MSC8122 Reference Manual. DREQ2 Input DMA Request 1 Used by an external peripheral to request DMA service. GPIO19 Input/ Output General-Purpose Input Output 19 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM1RCLK Input/ Output TDM1 Receive Clock The receive clock signal for TDM 1. As an input, this can be the DATA_C data signal for TDM 1. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. DACK2 Output DMA Acknowledge 2 The DMA controller drives this output to acknowledge the DMA transaction on the bus. GPIO20 Input/ Output General-Purpose Input Output 20 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM1RDAT Input/ Output TDM1 Serial Receiver Data The receive data signal for TDM 1. As an input, this can be the DATA_A data signal for TDM 1. For configuration details, refer to the MSC8122 Reference Manual. GPIO21 Input/ Output General-Purpose Input Output 21 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM0TSYN Input/ Output TDM0 Transmit frame Sync Transmit Frame Sync for TDM 0. GPIO22 Input/ Output General-Purpose Input Output 22 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs.For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM0TCLK DONE2 Input TDM 0 Transmit Clock Transmit Clock for TDM 0. Input/ Output DMA Done 2 Signifies that the channel must be terminated. If the DMA generates DONE, the channel handling this peripheral is inactive. As an input to the DMA, DONE closes the channel much like a normal channel closing. Note: DRACK2 Output See the MSC8122 Reference Manual chapters on DMA and GPIO for information on configuring the DRACK or DONE mode and pin direction. DMA Data Request Acknowledge 2 Asserted by the DMA controller to indicate that the DMA controller has sampled the peripheral request. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-21 Signals/Connections Table 1-7. Signal Name GPIO, TDM, UART, Ethernet, and Timer Signals (Continued) Type Description GPIO23 Input/ Output General-Purpose Input Output 23 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM0TDAT Input/ Output TDM0 Serial Transmitter Data The transmit data signal for TDM 0. As an output, this can be the DATA_D data signal for TDM 0. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ13 Input Interrupt Request 13 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. GPIO24 Input/ Output General-Purpose Input Output 24 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM0RSYN Input/ Output TDM0 Receive Frame Sync The receive sync signal for TDM 0. As an input, this can be the DATA_B data signal for TDM 0. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ14 Input Interrupt Request 14 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. GPIO25 Input/ Output General-Purpose Input Output 25 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM0RCLK Input/ Output TDM0 Receive Clock The receive clock signal for TDM 0. As an input, this can be the DATA_C data signal for TDM 0. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. IRQ15 Input Interrupt Request 15 One of fifteen external lines that can request a service routine, via the internal interrupt controller, from the SC140 core. GPIO26 Input/ Output General-Purpose Input Output 26 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TDM0RDAT Input/ Output TDM0 Serial Receiver Data The receive data signal for TDM 0. As an input, this can be the DATA_A data signal for TDM 0. For configuration details, refer to the MSC8122 Reference Manual chapter describing TDM operation. GPIO27 Input/ Output General-Purpose Input Output 27 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. DREQ1 Input DMA Request 1 Used by an external peripheral to request DMA service. URXD Input UART Receive Data GPIO28 DREQ2 UTXD Input/ Output General-Purpose Input Output 28 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. Input Output DMA Request 2 Used by an external peripheral to request DMA service. UART Transmit Data MSC8122 Technical Data, Rev. 12 1-22 Freescale Semiconductor Dedicated Ethernet Signals Table 1-7. Signal Name GPIO29 CHIP_ID3 ETHTX_EN GPIO, TDM, UART, Ethernet, and Timer Signals (Continued) Type Description Input/ Output General-Purpose Input Output 29 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. Input Output Chip ID 3 Determines the chip ID of the MSC8122 DSI. It is sampled on the rising edge of PORESET signal. Ethernet Transmit Enable Used to enable the Ethernet transmit controller for MII and RMII modes. GPIO30 Input/ Output General-Purpose Input Output 30 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs.For details, refer to the MSC8122 Reference Manual GPIO programming model. TIMER2 Input/ Output Timer 2 Each signal is configured as either input to the counter or output from the counter. For the configuration of the pin direction, refer to the MSC8122 Reference Manual. TMCLK Input External TIMER Clock An external timer can connect directly to the SIU as the SIU clock. SDA Input/ Output I2C-Bus Data Line This is the data line for the I2C bus. GPIO31 Input/ Output General-Purpose Input Output 31 One of 32 GPIO pins used as GPIO or as one of two dedicated inputs or one of two dedicated outputs. For details, refer to the MSC8122 Reference Manual GPIO programming model. TIMER3 Input/ Output Timer 3 Each signal is configured as either input to or output from the counter. For the configuration of the pin direction, refer to the MSC8122 Reference Manual. SCL Input/ Output I2C-Bus Clock Line This the clock line for the I2C bus. 1.7 Dedicated Ethernet Signals Most Ethernet signals are multiplexed with the DSI/system bus and the GPIO ports. In addition to the multiplexed signals, there are three dedicated Ethernet signals that are described in Table 1-8. Table 1-8. Signal Name Type Dedicated Ethernet Signals Signal Description ETHRX_CLK Input Receive Clock In MII mode, provides the timing reference for the receive signals. ETHSYNC_IN Input Sync Input In SMII mode, is the sync signal input line. ETHTX_CLK Input Transmit Clock In MII mode, provides the timing reference for transmit signals. ETHREF_CLK Input Reference Clock In RMII mode, provides the timing reference. ETHCLOCK Input Ethernet Clock In SMII mode, provides the Ethernet clock signal. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 1-23 Signals/Connections Table 1-8. Signal Name Dedicated Ethernet Signals Type Signal Description ETHCRS Input Carrier Sense In MII mode, indicates that either the transmit or receive medium is non-idle. ETHRXD Input Ethernet Receive Data In SMII mode, used for the Ethernet receive data. 1.8 EOnCE Event and JTAG Test Access Port Signals The MSC8122 uses two sets of debugging signals for the two types of internal debugging modules: EOnCE and the JTAG TAP controller. Each internal SC140 core has an EOnce module, but they are all accessed externally by the same two signals EE0 and EE1. The MSC8122 supports the standard set of test access port (TAP) signals defined by IEEE 1149.1 Standard Test Access Port and Boundary-Scan Architecture specification and described in Table 1-9. Table 1-9. Signal Name Type JTAG TAP Signals Signal Description EE0 Input EOnCE Event Bit 0 Puts the internal SC140 cores into Debug mode. EE1 Output TCK Input Test Clock--Synchronizes JTAG test logic. TDI Input Test Data Input--A test data serial signal for test instructions and data. TDI is sampled on the rising edge of TCK and has an internal pull-up resistor. TDO Output TMS Input Test Mode Select--Sequences the test controller state machine, is sampled on the rising edge of TCK, and has an internal pull-up resistor. TRST Input Test Reset--Asynchronously initializes the test controller; must be asserted during power up. EOnCE Event Bit 1 Indicates that at least one on-device SC140 core is in Debug mode. Test Data Output--A test data serial signal for test instructions and data. TDO can be tri-stated. The signal is actively driven in the shift-IR and shift-DR controller states and changes on the falling edge of TCK. 1.9 Reserved Signals Table 1-10. Signal Name TEST Type Input Reserved Signals Signal Description Test For manufacturing testing. You must connect this pin to GND. MSC8122 Technical Data, Rev. 12 1-24 Freescale Semiconductor 2 Specifications This document contains detailed informatRev. 12ion on power considerations, DC/AC electrical characteristics, and AC timing specifications. For additional information, see the MSC8122 User's Guide and MSC8122 Reference Manual. 2.1 Maximum Ratings CAUTION This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, normal precautions should be taken to avoid exceeding maximum voltage ratings. Reliability is enhanced if unused inputs are tied to an appropriate logic voltage level (for example, either GND or VDD). In calculating timing requirements, adding a maximum value of one specification to a minimum value of another specification does not yield a reasonable sum. A maximum specification is calculated using a worst case variation of process parameter values in one direction. The minimum specification is calculated using the worst case for the same parameters in the opposite direction. Therefore, a "maximum" value for a specification never occurs in the same device with a "minimum" value for another specification; adding a maximum to a minimum represents a condition that can never exist. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-1 Specifications Table 2-1 describes the maximum electrical ratings for the MSC8122. Table 2-1. Rating Absolute Maximum Ratings Symbol Value Unit Core and PLL supply voltage VDD -0.2 to 1.6 V I/O supply voltage VDDH -0.2 to 4.0 V Input voltage VIN -0.2 to 4.0 V Maximum operating temperature: * Standard range * Extended range TJ 90 105 C C Minimum operating temperature * Standard range * Extended range TJ 0 -40 C C -55 to +150 C Storage temperature range Notes: 1. 2. 3. TSTG Functional operating conditions are given in Table 2-2. Absolute maximum ratings are stress ratings only, and functional operation at the maximum is not guaranteed. Stress beyond the listed limits may affect device reliability or cause permanent damage. Section 4.5, Thermal Considerations includes a formula for computing the chip junction temperature (TJ). 2.2 Recommended Operating Conditions Table 2-2 lists recommended operating conditions. Proper device operation outside of these conditions is not guaranteed. Table 2-2. Rating Recommended Operating Conditions Value Unit 1.14 to 1.26 1.16 to 1.24 1.07 to 1.13 V V V VDDH 3.135 to 3.465 V Input voltage VIN -0.2 to VDDH+0.2 V Operating temperature range: * Standard * Extended TJ TJ 0 to 90 -40 to 105 C C Core and PLL supply voltage: * Standard -- 400 MHz -- 500 MHz * Reduced (300 and 400 MHz) I/O supply voltage Symbol VDD VCCSYN MSC8122 Technical Data, Rev. 12 2-2 Freescale Semiconductor Thermal Characteristics 2.3 Thermal Characteristics Table 2-3 describes thermal characteristics of the MSC8122 for the FC-PBGA packages. Table 2-3. Characteristic Thermal Characteristics for the MSC8122 FC-PBGA 20 x 20 mm5 Symbol Unit Natural Convection 200 ft/min (1 m/s) airflow RJA 26 21 Junction-to-ambient, four-layer board RJA 19 15 Junction-to-board (bottom)4 RJB 9 C/W Junction-to-case5 RJC 0.9 C/W JT 1 C/W Junction-to-ambient1, 2 1, 3 Junction-to-package-top6 Notes: 1. 2. 3. 4. 5. 6. C/W C/W Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board horizontal. Per JEDEC JESD51-6 with the board horizontal. Thermal resistance between the die and the printed circuit board per JEDEC JESD 51-8. Board temperature is measured on the top surface of the board near the package. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1). Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per JEDEC JESD51-2. Section 4.5, Thermal Considerations provides a detailed explanation of these characteristics. 2.4 DC Electrical Characteristics This section describes the DC electrical characteristics for the MSC8122. The measurements in Table 2-4 assume the following system conditions: * * TA = 25 C VDD = -- 300/400 MHz 1.1 V nominal = 1.07-1.13 VDC -- 400 MHz 1.2 V nominal = 1.14-1.26 VDC -- 500 MHz 1.2 V nominal = 1.16-1.24 VDC * * = 3.3 V 5% VDC GND = 0 VDC VDDH Note: The leakage current is measured for nominal VDDH and VDD. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-3 Specifications Table 2-4. DC Electrical Characteristics Characteristic Symbol Min Typical Max Unit Input high voltage1, all inputs except CLKIN VIH 2.0 -- 3.465 V Input low voltage1 VIL GND 0 0.4 V CLKIN input high voltage VIHC 2.4 3.0 3.465 V CLKIN input low voltage VILC GND 0 0.4 V Input leakage current, VIN = VDDH IIN -1.0 0.09 1 A Tri-state (high impedance off state) leakage current, VIN = VDDH IOZ -1.0 0.09 1 A Signal low input current, VIL = 0.4 V 2 IL -1.0 0.09 1 A IH -1.0 0.09 1 A Output high voltage, IOH = -2 mA, except open drain pins VOH 2.0 3.0 -- V Output low voltage, IOL= 3.2 mA VOL -- 0 0.4 V Internal supply current: * Wait mode * Stop mode IDDW IDDS -- -- 3753 2903 -- -- mA mA P -- 1.15 -- W Signal high input current, VIH = 2.0 V2 Typical power 400 MHz at 1.2 V4 Notes: 1. 2. 3. 4. See Figure 2-1 for undershoot and overshoot voltages. Not tested. Guaranteed by design. Measured for 1.2 V core at 25C junction temperature. The typical power values were measured using an EFR code with the device running at a junction temperature of 25C. No peripherals were enabled and the ICache was not enabled. The source code was optimized to use all the ALUs and AGUs and all four cores. It was created using CodeWarrior(R) 2.5. These values are provided as examples only. Power consumption is application dependent and varies widely. To assure proper board design with regard to thermal dissipation and maintaining proper operating temperatures, evaluate power consumption for your application and use the design guidelines in Chapter 4 of this document and in MSC8102, MSC8122, and MSC8126 Thermal Management Design Guidelines (AN2601). VIH VDDH + 17% VDDH + 8% VDDH VIL GND GND - 0.3 V GND - 0.7 V Must not exceed 10% of clock period Figure 2-1. Overshoot/Undershoot Voltage for VIH and VIL 2.5 AC Timings The following sections include illustrations and tables of clock diagrams, signals, and parallel I/O outputs and inputs. When systems such as DSP farms are developed using the DSI, use a device loading of 4 pF per pin. AC timings are based on a 20 pF load, except where noted otherwise, and a 50 transmission line. For loads smaller than 20 pF, subtract 0.06 ns per pF down to 10 pF load. For loads larger than 20 pF, add 0.06 ns for SIU/Ethernet/DSI delay and 0.07 ns for GPIO/TDM/timer delay. When calculating overall loading, also consider additional RC delay. MSC8122 Technical Data, Rev. 12 2-4 Freescale Semiconductor AC Timings 2.5.1 Output Buffer Impedances Table 2-5. Output Buffer Impedances Output Buffers Typical Impedance () System bus 50 Memory controller 50 Parallel I/O 50 Note: 2.5.2 These are typical values at 65C. The impedance may vary by 25% depending on device process and operating temperature. Start-Up Timing Starting the device requires coordination among several input sequences including clocking, reset, and power. Section 2.5.3 describes the clocking characteristics. Section 2.5.4 describes the reset and power-up characteristics. You must use the following guidelines when starting up an MSC8122 device: * * * * PORESET and TRST must be asserted externally for the duration of the power-up sequence. See Table 2-10 for timing. If possible, bring up the VDD and VDDH levels together. For designs with separate power supplies, bring up the VDD levels and then the VDDH levels (see Figure 2-3). CLKIN should start toggling at least 16 cycles (starting after VDDH reaches its nominal level) before PORESET deassertion to guarantee correct device operation (see Figure 2-2 and Figure 2-3). CLKIN must not be pulled high during VDDH power-up. CLKIN can toggle during this period. The following figures show acceptable start-up sequence examples. Figure 2-2 shows a sequence in which VDD and VDDH are raised together. Figure 2-3 shows a sequence in which VDDH is raised after VDD and CLKIN begins to toggle as VDDH rises. VDDH = Nominal Value VDD = Nominal Value 1 VDDH Nominal Level Voltage 3.3 V 2.2 V 1.2 V VDD Nominal Level o.5 V Time PORESET/TRST Deasserted CLKIN Starts Toggling PORESET/TRST Asserted VDD/VDDH Applied Figure 2-2. Start-Up Sequence with VDD and VDDH Raised Together MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-5 Specifications VDDH = Nominal VDD = Nominal 1 VDDH Nominal Voltage 3.3 V 1.2 V VDD Nominal o.5 V Time PORESET/TRST asserted VDD applied PORESET/TRST deasserted CLKIN starts toggling VDDH applied Figure 2-3. 2.5.3 Start-Up Sequence with VDD Raised Before VDDH with CLKIN Started with VDDH Clock and Timing Signals The following sections include a description of clock signal characteristics. Table 2-6 shows the maximum frequency values for internal (Core, Reference, Bus, and DSI) and external (CLKIN and CLKOUT) clocks. The user must ensure that maximum frequency values are not exceeded. Table 2-6. Maximum Frequencies Characteristic Maximum in MHz Core frequency 300/400/500 Reference frequency (REFCLK) 100/133/166 Internal bus frequency (BLCK) 100/133/166 DSI clock frequency (HCLKIN) * Core frequency = 300 MHz * Core frequency = 400/500 MHz HCLKIN (min{70 MHz, CLKOUT}) HCLKIN (min{100 MHz, CLKOUT}) External clock frequency (CLKIN or CLKOUT) 100/133/166 Table 2-7. Characteristics Clock Frequencies 300 MHz Device 400 MHz Device 500 MHz Device Min Max Min Max Min Max FCLKIN 20 100 20 133.3 20 166.7 Symbol CLKIN frequency BCLK frequency FBCLK 40 100 40 133.3 40 166.7 Reference clock (REFCLK) frequency FREFCLK 40 100 40 133.3 40 166.7 Output clock (CLKOUT) frequency FCLKOUT 40 100 40 133.3 40 166.7 FCORE 200 300 200 400 200 500 SC140 core clock frequency Note: The rise and fall time of external clocks should be 3 ns maximum Table 2-8. Characteristic System Clock Parameters Min Max Phase jitter between BCLK and CLKIN -- 0.3 Unit ns CLKIN frequency 20 see Table 2-7 MHz CLKIN slope -- 3 ns PLL input clock (after predivider) 20 100 MHz MSC8122 Technical Data, Rev. 12 2-6 Freescale Semiconductor AC Timings Table 2-8. System Clock Parameters Characteristic Min PLL output frequency (VCO output) * 300 MHz core * 400 MHz core * 500 MHz core Max Unit 1200 1600 2000 MHz MHz MHz MHz 800 CLKOUT frequency jitter1 -- 200 ps CLKOUT phase jitter1 with CLKIN phase jitter of 100 ps. -- 500 ps Notes: 1. 2. 2.5.4 Peak-to-peak. Not tested. Guaranteed by design. Reset Timing The MSC8122 has several inputs to the reset logic: * * * * * * Power-on reset (PORESET) External hard reset (HRESET) External soft reset (SRESET) Software watchdog reset Bus monitor reset Host reset command through JTAG All MSC8122 reset sources are fed into the reset controller, which takes different actions depending on the source of the reset. The reset status register indicates the most recent sources to cause a reset. Table 2-9 describes the reset sources. Table 2-9. Name Reset Sources Direction Description Power-on reset (PORESET) Input Initiates the power-on reset flow that resets the MSC8122 and configures various attributes of the MSC8122. On PORESET, the entire MSC8122 device is reset. SPLL states is reset, HRESET and SRESET are driven, the SC140 extended cores are reset, and system configuration is sampled. The clock mode (MODCK bits), reset configuration mode, boot mode, Chip ID, and use of either a DSI 64 bits port or a System Bus 64 bits port are configured only when PORESET is asserted. External hard reset (HRESET) Input/ Output Initiates the hard reset flow that configures various attributes of the MSC8122. While HRESET is asserted, SRESET is also asserted. HRESET is an open-drain pin. Upon hard reset, HRESET and SRESET are driven, the SC140 extended cores are reset, and system configuration is sampled. The most configurable features are reconfigured. These features are defined in the 32-bit hard reset configuration word described in Hard Reset Configuration Word section of the Reset chapter in the MSC8122 Reference Manual. External soft reset (SRESET) Input/ Output Initiates the soft reset flow. The MSC8122 detects an external assertion of SRESET only if it occurs while the MSC8122 is not asserting reset. SRESET is an open-drain pin. Upon soft reset, SRESET is driven, the SC140 extended cores are reset, and system configuration is maintained. Software watchdog reset Internal When the MSC8122 watchdog count reaches zero, a software watchdog reset is signalled. The enabled software watchdog event then generates an internal hard reset sequence. Bus monitor reset Internal When the MSC8122 bus monitor count reaches zero, a bus monitor hard reset is asserted. The enabled bus monitor event then generates an internal hard reset sequence. Host reset command through the TAP Internal When a host reset command is written through the Test Access Port (TAP), the TAP logic asserts the soft reset signal and an internal soft reset sequence is generated. Table 2-10 summarizes the reset actions that occur as a result of the different reset sources. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-7 Specifications Table 2-10. Reset Actions for Each Reset Source Power-On Reset (PORESET) Hard Reset (HRESET) External only External or Internal (Software Watchdog or Bus Monitor) External JTAG Command: EXTEST, CLAMP, or HIGHZ Yes No No No Soft Reset (SRESET) Reset Action/Reset Source Configuration pins sampled (Refer to Section 2.5.4.1 for details). SPLL state reset Yes No No No System reset configuration write through the DSI Yes No No No System reset configuration write though the system bus Yes Yes No No HRESET driven Yes Yes No No SIU registers reset Yes Yes No No IPBus modules reset (TDM, UART, Timers, DSI, IPBus master, GIC, HS, and GPIO) Yes Yes Yes Yes SRESET driven Yes Yes Yes Depends on command SC140 extended cores reset Yes Yes Yes Yes MQBS reset Yes Yes Yes Yes 2.5.4.1 Power-On Reset (PORESET) Pin Asserting PORESET initiates the power-on reset flow. PORESET must be asserted externally for at least 16 CLKIN cycles after VDD and VDDH are both at their nominal levels. 2.5.4.2 Reset Configuration The MSC8122 has two mechanisms for writing the reset configuration: * * Through the direct slave interface (DSI) Through the system bus. When the reset configuration is written through the system bus, the MSC8122 acts as a configuration master or a configuration slave. If configuration slave is selected, but no special configuration word is written, a default configuration word is applied. Fourteen signal levels (see Chapter 1 for signal description details) are sampled on PORESET deassertion to define the Reset Configuration Mode and boot and operating conditions: * * * * * * * * RSTCONF CNFGS DSISYNC DSI64 CHIP_ID[0-3] BM[0-2] SWTE MODCK[1-2] MSC8122 Technical Data, Rev. 12 2-8 Freescale Semiconductor AC Timings 2.5.4.3 Reset Timing Tables Table 2-11 and Figure 2-4 describe the reset timing for a reset configuration write through the direct slave interface (DSI) or through the system bus. Table 2-11. Timing for a Reset Configuration Write through the DSI or System Bus No. 1 Characteristics Expression Required external PORESET duration minimum * CLKIN = 20 MHz * CLKIN = 100 MHz (300 MHz core) * CLKIN = 133 MHz (400 MHz core) * CLKIN = 166 MHz (500 MHz core) Delay from deassertion of external PORESET to deassertion of internal PORESET * CLKIN = 20 MHz to 166 MHz 3 Delay from de-assertion of internal PORESET to SPLL lock * CLKIN = 20 MHz (RDF = 1) * CLKIN = 100 MHz (RDF = 1) (300 MHz core) * CLKIN = 133 MHz (RDF = 2) (400 MHz core) * CLKIN = 166 MHz (RDF = 2) (500 MHz core) 6 Max Unit 800 160 120 96 -- -- -- -- ns ns ns ns 6.17 51.2 s 320 64 96 77 320 64 96 77 s s s s 3.08 12.8 s 3.10 12.88 s 16/CLKIN 2 5 Min 1024/CLKIN 6400/(CLKIN/RDF) (PLL reference clockdivision factor) Delay from SPLL to HRESET deassertion * REFCLK = 40 MHz to 166 MHz 512/REFCLK Delay from SPLL lock to SRESET deassertion * REFCLK = 40 MHz to 166 MHz 515/REFCLK 7 Setup time from assertion of RSTCONF, CNFGS, DSISYNC, DSI64, CHIP_ID[0-3], BM[0-2], SWTE, and MODCK[1-2] before deassertion of PORESET 3 -- ns 8 Hold time from deassertion of PORESET to deassertion of RSTCONF, CNFGS, DSISYNC, DSI64, CHIP_ID[0-3], BM[0-2], SWTE, and MODCK[1-2] 5 -- ns Note: Timings are not tested, but are guaranteed by design. RSTCONF, CNFGS, DSISYNC, DSI64 CHIP_ID[0-3], BM[0-2], SWTE, MODCK[1-2] pins are sampled 1 PORESET Input Host programs Reset Configuration Word PORESET Internal 1+2 MODCK[3-5] SPLL is locked (no external indication) HRESET Output (I/O) 2 SRESET Output (I/O) Reset configuration write sequence during this period. Figure 2-4. 3 SPLL locking period 5 6 Timing Diagram for a Reset Configuration Write MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-9 Specifications 2.5.5 System Bus Access Timing 2.5.5.1 Core Data Transfers Generally, all MSC8122 bus and system output signals are driven from the rising edge of the reference clock (REFCLK). The REFCLK is the CLKIN signal. Memory controller signals, however, trigger on four points within a REFCLK cycle. Each cycle is divided by four internal ticks: T1, T2, T3, and T4. T1 always occurs at the rising edge of REFCLK (and T3 at the falling edge), but the spacing of T2 and T4 depends on the PLL clock ratio selected, as Table 2-12 shows. Table 2-12. Tick Spacing for Memory Controller Signals Tick Spacing (T1 Occurs at the Rising Edge of REFCLK) BCLK/SC140 clock T2 T3 T4 1:4, 1:6, 1:8, 1:10 1/4 REFCLK 1/2 REFCLK 3/4 REFCLK 1:3 1/6 REFCLK 1/2 REFCLK 4/6 REFCLK 1:5 2/10 REFCLK 1/2 REFCLK 7/10 REFCLK Figure 2-5 is a graphical representation of Table 2-12. for 1:4, 1:6, 1:8, 1:10 REFCLK T1 T2 T3 T4 REFCLK for 1:3 T1 T2 T3 T4 REFCLK for 1:5 T1 T2 Figure 2-5. T3 T4 Internal Tick Spacing for Memory Controller Signals MSC8122 Technical Data, Rev. 12 2-10 Freescale Semiconductor AC Timings The UPM machine and GPCM machine outputs change on the internal tick selected by the memory controller configuration. The AC timing specifications are relative to the internal tick. SDRAM machine outputs change only on the REFCLK rising edge. Table 2-13. AC Timing for SIU Inputs Value for Bus Speed in MHz Ref = CLKIN No. Characteristic Ref = CLKOUT 1.1 V 1.2 V 1.2 V 1.2 V 100/ 133 133 166 133 Units 10 Hold time for all signals after the 50% level of the REFCLK rising edge 0.5 0.5 0.5 0.5 ns 11a ARTRY/ABB set-up time before the 50% level of the REFCLK rising edge 3.1 3.0 3.0 3.0 ns 11b DBG/DBB/BG/BR/TC set-up time before the 50% level of the REFCLK rising edge 3.6 3.3 3.3 3.3 ns 11c AACK set-up time before the 50% level of the REFCLK rising edge 3.0 2.9 2.9 2.9 ns 11d TA/TEA/PSDVAL set-up time before the 50% level of the REFCLK rising edge * Data-pipeline mode * Non-pipeline mode 3.5 4.4 3.4 4.0 3.4 4.0 3.4 4.0 ns ns Data bus set-up time before REFCLK rising edge in Normal mode * Data-pipeline mode * Non-pipeline mode 1.9 4.2 1.8 4.0 1.7 4.0 1.8 4.0 ns ns Data bus set-up time before the 50% level of the REFCLK rising edge in ECC and PARITY modes * Data-pipeline mode * Non-pipeline mode 2.0 8.2 2.0 7.3 2.0 7.3 2.0 7.3 ns ns DP set-up time before the 50% level of the REFCLK rising edge * Data-pipeline mode * Non-pipeline mode 2.0 7.9 2.0 6.1 2.0 6.1 2.0 6.1 ns ns TS and Address bus set-up time before the 50% level of the REFCLK rising edge * Extra cycle mode (SIUBCR[EXDD] = 0) * No extra cycle mode (SIUBCR[EXDD] = 1) 4.2 5.5 3.8 5.0 3.8 5.0 3.8 5.0 ns ns Address attributes: TT/TBST/TSZ/GBL set-up time before the 50% level of the REFCLK rising edge * Extra cycle mode (SIUBCR[EXDD] = 0) * No extra cycle mode (SIUBCR[EXDD] = 1) 3.7 4.8 3.5 4.4 3.5 4.4 3.5 4.4 ns ns 3.7 3.7 3.7 3.7 ns 12 131 141 15a 15b 16 Notes: PUPMWAIT signal set-up time before the 50% level of the REFCLK rising edge 1. 2. Timings specifications 13 and 14 in non-pipeline mode are more restrictive than MSC8102 timings. Values are measured from the 50% TTL transition level relative to the 50% level of the REFCLK rising edge. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-11 Specifications Table 2-14. AC Timing for SIU Outputs Value for Bus Speed in MHz3 Ref = CLKIN No. Characteristic Ref = CLKOUT 1.1 V 1.2 V 1.2 V 1.2 V 100/ 133 133 166 100/133 Units 302 Minimum delay from the 50% level of the REFCLK for all signals 0.9 0.8 0.8 1.0 ns 31 PSDVAL/TEA/TA max delay from the 50% level of the REFCLK rising edge 6.0 4.9 4.9 5.8 ns 32a Address bus max delay from the 50% level of the REFCLK rising edge * Multi-master mode (SIUBCR[EBM] = 1) * Single-master mode (SIUBCR[EBM] = 0) 6.4 5.3 5.5 4.2 5.5 3.9 6.4 5.1 ns ns 32b Address attributes: TT[0-1]/TBST/TSZ/GBL max delay from the 50% level of the REFCLK rising edge 6.4 5.1 5.1 6.0 ns 32c Address attributes: TT[2-4]/TC max delay from the 50% level of the REFCLK rising edge 6.9 5.7 5.7 6.6 ns 32d BADDR max delay from the 50% level of the REFCLK rising edge 5.2 4.2 4.2 5.1 ns 33a Data bus max delay from the 50% level of the REFCLK rising edge * Data-pipeline mode * Non-pipeline mode 4.8 7.1 3.9 6.1 3.7 6.1 4.8 7.0 ns ns DP max delay from the 50% level of the REFCLK rising edge * Data-pipeline mode * Non-pipeline mode 6.0 7.5 5.3 6.5 5.3 6.5 6.2 7.4 ns ns 33b 34 Memory controller signals/ALE/CS[0-4] max delay from the 50% level of the REFCLK rising edge 5.1 4.2 3.9 5.1 ns 35a DBG/BG/BR/DBB max delay from the 50% level of the REFCLK rising edge 6.0 4.7 4.7 5.6 ns 35b AACK/ABB/TS/CS[5-7] max delay from the 50% level of the REFCLK rising edge 5.5 4.5 4.5 5.4 ns Notes: 1. 2. 3. Values are measured from the 50% level of the REFCLK rising edge to the 50% signal level and assume a 20 pF load except where otherwise specified. The load for specification 30 is 10 pF. The load for the other specifications in this table is 20 pF. For a 15 pF load, subtract 0.3 ns from the listed value. The maximum bus frequency depends on the mode: * In 60x-compatible mode connected to another MSC8122 device, the frequency is determined by adding the input and output longest timing values, which results in the total delay for 20 pF output capacitance. You must also account for other influences that can affect timing, such as on-board clock skews, on-board noise delays, and so on. * In single-master mode, the frequency depends on the timing of the devices connected to the MSC8122. * To achieve maximum performance on the bus in single-master mode, disable the DBB signal by writing a 1 to the SIUMCR[BDD] bit. See the SIU chapter in the MSC8122 Reference Manual for details. MSC8122 Technical Data, Rev. 12 2-12 Freescale Semiconductor AC Timings REFCLK 10 AACK/ARTRY/TA/TEA/DBG/BG/BR PSDVAL/ABB/DBB inputs 11 10 12 Data bus inputs--normal mode 10 Data bus inputs--ECC and parity modes 13 DP inputs 14 Address bus/TS /TT[0-4]/TC[0-2]/ TBST/TSZ[0-3]/GBL inputs 15 PUPMWAIT input 10 16 30 Min delay for all output pins 31 PSDVAL/TEA/TA outputs 32a/b Address bus/TT[0-4]/TC[0-2]/TBST/TSZ[0-3]/GBL outputs BADDR outputs Data bus outputs DP outputs Memory controller/ALE outputs 32c 33a 33b 34 35 AACK/ABB/TS/DBG/BG/BR/DBB/CS outputs Figure 2-6. Bus Signal Timing MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-13 Specifications 2.5.5.2 CLKIN to CLKOUT Skew Table 2-16 describes the CLKOUT-to-CLKIN skew timing. Table 2-15. Min1 Max1 Units Rise-to-rise skew * VDD = 1.1 V * VDD = 1.2 V 0.0 0.0 0.95 0.85 ns ns Fall-to-fall skew * VDD = 1.1 V * VDD = 1.2 V -1.5 -0.8 1.0 1.0 ns ns CLKOUT phase (1.2 V, 133 MHz) * Phase high * Phase low 2.8 2.8 -- -- ns ns CLKOUT phase (1.1 V, 133 MHz) * Phase high * Phase low 2.2 2.2 -- -- ns ns CLKOUT phase (1.1 V, 100 MHz) * Phase high * Phase low 3.3 3.3 -- -- ns ns No. 20 21 22 23 24 Notes: CLKOUT Skew Characteristic 1. 2. 3. 4. A positive number indicates that CLKOUT precedes CLKIN, A negative number indicates that CLKOUT follows CLKIN. Skews are measured in clock mode 29, with a CLKIN:CLKOUT ratio of 1:1. The same skew is valid for all clock modes. CLKOUT skews are measured using a load of 10 pF. CLKOUT skews and phase are not measured for 500/166 Mhz parts because these parts only use CLKIN mode. For designs that use the CLKOUT synchronization mode, use the skew values listed in Table 2-15 to adjust the riseto-fall timing values specified for CLKIN synchronization. Figure 2-7 shows the relationship between the CLKOUT and CLKIN timings. CLKIN CLKOUT 20 Figure 2-7. 21 CLKOUT and CLKIN Signals. MSC8122 Technical Data, Rev. 12 2-14 Freescale Semiconductor AC Timings 2.5.5.3 DMA Data Transfers Table 2-16 describes the DMA signal timing. Table 2-16. DMA Signals Ref = CLKIN No. Characteristic Min Max Ref = CLKOUT (1.2 V only) Min Units Max 37 DREQ set-up time before the 50% level of the falling edge of REFCLK 5.0 -- 5.0 -- ns 38 DREQ hold time after the 50% level of the falling edge of REFCLK 0.5 -- 0.5 -- ns ns 39 DONE set-up time before the 50% level of the rising edge of REFCLK 5.0 -- 5.0 -- 40 DONE hold time after the 50% level of the rising edge of REFCLK 0.5 -- 0.5 -- ns 41 DACK/DRACK/DONE delay after the 50% level of the REFCLK rising edge 0.5 7.5 0.5 8.4 ns The DREQ signal is synchronized with REFCLK. To achieve fast response, a synchronized peripheral should assert DREQ according to the timings in Table 2-16. Figure 2-8 shows synchronous peripheral interaction. REFCLK 38 37 DREQ 40 39 DONE 41 DACK/DONE/DRACK Figure 2-8. DMA Signals MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-15 Specifications 2.5.6 DSI Timing The timings in the following sections are based on a 20 pF capacitive load. 2.5.6.1 DSI Asynchronous Mode Table 2-17. No. DSI Asynchronous Mode Timing Characteristics Min 1 Max Unit 100 Attributes set-up time before strobe (HWBS[n]) assertion 1.5 -- ns 101 Attributes1 hold time after data strobe deassertion 1.3 -- ns 102 Read/Write data strobe deassertion width: * DCR[HTAAD] = 1 -- Consecutive access to the same DSI -- Different device with DCR[HTADT] = 01 -- Different device with DCR[HTADT] = 10 -- Different device with DCR[HTADT] = 11 * DCR[HTAAD] = 0 -- ns ns ns ns ns 1.8 + TREFCLK 5 + TREFCLK 5 + (1.5 x TREFCLK) 5 + (2.5 x TREFCLK) 1.8 + TREFCLK 103 Read data strobe deassertion to output data high impedance -- 8.5 104 Read data strobe assertion to output data active from high impedance 2.0 -- ns ns 105 Output data hold time after read data strobe deassertion 2.2 -- ns 106 Read/Write data strobe assertion to HTA active from high impedance 2.2 -- ns 107 Output data valid to HTA assertion 3.2 -- ns 108 Read/Write data strobe assertion to HTA valid2 * 1.1 V core * 1.2 V core -- -- 7.4 6.7 ns ns 109 Read/Write data strobe deassertion to output HTA high impedance. (DCR[HTAAD] = 0, HTA at end of access released at logic 0) -- 6.5 ns 110 Read/Write data strobe deassertion to output HTA deassertion. (DCR[HTAAD] = 1, HTA at end of access released at logic 1) -- 6.5 ns 111 Read/Write data strobe deassertion to output HTA high impedance. (DCR[HTAAD] = 1, HTA at end of access released at logic 1 * DCR[HTADT] = 01 * DCR[HTADT] = 10 * DCR[HTADT] = 11 -- 5 + TREFCLK 5 + (1.5 x TREFCLK) 5 + (2.5 x TREFCLK) ns ns ns 112 Read/Write data strobe assertion width 1.8 + TREFCLK -- ns 201 Host data input set-up time before write data strobe deassertion 1.0 -- ns 202 Host data input hold time after write data strobe deassertion * 1.1 V core * 1.2 V core 1.7 1.5 -- -- ns ns Notes: 1. 2. 3. Attributes refers to the following signals: HCS, HA[11-29], HCID[0-4], HDST, HRW, HRDS, and HWBSn. This specification is tested in dual-strobe mode. Timing in single-strobe mode is guaranteed by design. All values listed in this table are tested or guaranteed by design. MSC8122 Technical Data, Rev. 12 2-16 Freescale Semiconductor AC Timings Figure 2-9 shows DSI asynchronous read signals timing. HCS HA[11-29] HCID[0-4] HDST HRW1 HWBSn2 100 101 112 HDBSn1 HRDS2 102 103 107 105 104 HD[0-63] 106 109 HTA3 108 110 HTA4 111 Notes: 1. 2. 3. 4. Figure 2-9. Used for single-strobe mode access. Used for dual-strobe mode access. HTA released at logic 0 (DCR[HTAAD] = 0) at end of access; used with pulldown implementation. HTA released at logic 1 (DCR[HTAAD] = 1) at end of access; used with pull-up implementation. Asynchronous Single- and Dual-Strobe Modes Read Timing Diagram MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-17 Specifications Figure 2-10 shows DSI asynchronous write signals timing. HCS HA[11-29] HCID[0-4] HDST HRW1 HRDS2 101 100 112 HDBSn1 HWBSn2 102 201 202 HD[0-63] 109 106 HTA3 108 110 HTA4 111 Notes: 1. 2. 3. 4. Used for single-strobe mode access. Used for dual-strobe mode access. HTA released at logic 0 (DCR[HTAAD] = 0) at end of access; used with pull-down implementation. HTA released at logic 1 (DCR[HTAAD] = 1) at end of access; used with pull-up implementation. Figure 2-10. Asynchronous Single- and Dual-Strobe Modes Write Timing Diagram Figure 2-11 shows DSI asynchronous broadcast write signals timing. HCS HA[11-29] HCID[0-4] HDST HRW1 HRDS2 101 100 112 HDBSn1 HWBSn2 102 201 202 HD[0-63] Notes: 1. 2. Used for single-strobe mode access. Used for dual-strobe mode access. Figure 2-11. Asynchronous Broadcast Write Timing Diagram MSC8122 Technical Data, Rev. 12 2-18 Freescale Semiconductor AC Timings 2.5.6.2 DSI Synchronous Mode Table 2-18. DSI Inputs in Synchronous Mode 1.1 V Core No. Characteristic 1.2 V Core Expression Units Min Max Min Max 120 HCLKIN cycle time1,2 HTC 10.0 55.6 10.0 55.6 ns 121 HCLKIN high pulse width (0.5 0.1) x HTC 4.0 33.3 4.0 33.3 ns 122 HCLKIN low pulse width (0.5 0.1) x HTC 4.0 33.3 4.0 33.3 ns 123 HA[11-29] inputs set-up time -- 1.2 -- 1.2 -- ns 124 HD[0-63] inputs set-up time -- 0.6 -- 0.4 -- ns 125 HCID[0-4] inputs set-up time -- 1.3 -- 1.3 -- ns 126 All other inputs set-up time -- 1.2 -- 1.2 -- ns 127 All inputs hold time -- 1.5 -- 1.5 -- ns Notes: 1. 2. Values are based on a frequency range of 18-100 MHz. Refer to Table 2-6 for HCLKIN frequency limits. Table 2-19. DSI Outputs in Synchronous Mode 1.1 V Core No. 1.2 V Core Characteristic Units Min Max Min Max 128 HCLKIN high to HD[0-63] output active 2.0 -- 2.0 -- 129 HCLKIN high to HD[0-63] output valid -- 7.6 -- 6.3 ns ns 130 HD[0-63] output hold time 1.7 -- 1.7 -- ns 131 HCLKIN high to HD[0-63] output high impedance -- 8.3 -- 7.6 ns 132 HCLKIN high to HTA output active 2.2 -- 2.0 -- ns 133 HCLKIN high to HTA output valid -- 7.4 -- 5.9 ns 134 HTA output hold time 1.7 -- 1.7 -- ns 135 HCLKIN high to HTA high impedance -- 7.5 -- 6.3 ns 120 121 HCLKIN 122 127 123 HA[11-29] input signals 127 124 HD[0-63] input signals 127 125 HCID[0-4] input signals 127 126 All other input signals 131 129 HD[0-63] output signals 130 ~ ~ ~ ~ 128 135 133 132 Figure 2-12. 134 ~ ~ HTA output signal DSI Synchronous Mode Signals Timing Diagram MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-19 Specifications 2.5.7 TDM Timing Table 2-20. TDM Timing 1.1 V Core No. Characteristic 1.2 V Core Expression Units Min Max Min Max TC1 16 -- 16 -- TDMxRCLK/TDMxTCLK high pulse width (0.5 0.1) x TC 7 -- 7 -- ns 302 TDMxRCLK/TDMxTCLK low pulse width (0.5 0.1) x TC 7 -- 7 -- ns 303 TDM receive all input set-up time 1.3 -- 1.3 -- ns 304 TDM receive all input hold time 1.0 -- 1.0 -- ns 305 TDMxTCLK high to TDMxTDAT/TDMxRCLK output active2,3 2.8 -- 2.8 -- ns 306 TDMxTCLK high to TDMxTDAT/TDMxRCLK output -- 10.0 -- 8.8 ns 307 All output hold time4 2.5 -- 2.5 -- ns 308 TDMxTCLK high to TDmXTDAT/TDMxRCLK output high impedance2,3 -- 10.7 -- 10.5 ns 309 TDMxTCLK high to TDMXTSYN output valid2 -- 9.7 -- 8.5 ns 310 TDMxTSYN output hold time4 2.5 -- 2.5 -- ns 300 TDMxRCLK/TDMxTCLK 301 Notes: 1. 2. 3. 4. ns Values are based on a a maximum frequency of 62.5 MHz. The TDM interface supports any frequency below 62.5 MHz. Devices operating at 300 MHz are limited to a maximum TDMxRCLK/TDMxTCLK frequency of 50 MHz. Values are based on 20 pF capacitive load. When configured as an output, TDMxRCLK acts as a second data link. See the MSC8122 Reference Manual for details. Values are based on 10 pF capacitive load. 300 302 301 TDMxRCLK 304 303 TDMxRDAT 304 303 TDMxRSYN Figure 2-13. TDM Inputs Signals 300 302 301 TDMxTCLK 308 305 TDMxTDAT TDMxRCLK 309 TDMxTSYN Figure 2-14. ~ ~ ~ ~ 306 307 310 TDM Output Signals MSC8122 Technical Data, Rev. 12 2-20 Freescale Semiconductor AC Timings 2.5.8 UART Timing Table 2-21. No. UART Timing Characteristics Expression Min 16 x TREFCLK 160.0 Max Un it 400 URXD and UTXD inputs high/low duration -- ns 401 URXD and UTXD inputs rise/fall time 10 ns 402 UTXD output rise/fall time 10 ns 401 401 UTXD, URXD inputs 400 Figure 2-15. 402 400 UART Input Timing 402 UTXD output Figure 2-16. UART Output Timing MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-21 Specifications 2.5.9 Timer Timing Table 2-22. Timer Timing Ref = CLKIN No. Characteristics Unit Min Max 500 TIMERx frequency 10.0 -- ns 501 TIMERx Input high period 4.0 -- ns 502 TIMERx Output low period 4.0 -- ns 503 TIMERx Propagations delay from its clock input * 1.1 V core * 1.2 V core 3.1 2.8 9.5 8.1 ns ns Min Max Unit 500 501 502 TIMERx (Input) 503 TIMERx (Output) Figure 2-17. Timer Timing 2.5.10 Ethernet Timing 2.5.10.1 Management Interface Timing Table 2-23. No. Ethernet Controller Management Interface Timing Characteristics 801 ETHMDIO to ETHMDC rising edge set-up time 10 -- ns 802 ETHMDC rising edge to ETHMDIO hold time 10 -- ns ETHMDC 801 802 Valid ETHMDIO Figure 2-18. MDIO Timing Relationship to MDC MSC8122 Technical Data, Rev. 12 2-22 Freescale Semiconductor AC Timings 2.5.10.2 MII Mode Timing Table 2-24. No. MII Mode Signal Timing Min Max 803 ETHRX_DV, ETHRXD[0-3], ETHRX_ER to ETHRX_CLK rising edge set-up time Characteristics 3.5 -- Unit ns 804 ETHRX_CLK rising edge to ETHRX_DV, ETHRXD[0-3], ETHRX_ER hold time 3.5 -- ns 805 ETHTX_CLK to ETHTX_EN, ETHTXD[0-3], ETHTX_ER output delay * 1.1 V core * 1.2 V core 1 1 14.6 12.6 ns ns ETHRX_CLK 803 804 ETHRX_DV ETHRXD[0-3] ETHRX_ER Valid ETHTX_CLK 805 ETHTX_EN ETHTXD[0-3] ETHTX_ER Valid Figure 2-19. Valid MII Mode Signal Timing 2.5.10.3 RMII Mode Table 2-25. RMII Mode Signal Timing 1.1 V Core No. 1.2 V Core Characteristics Unit Min Max Min Max 806 ETHTX_EN,ETHRXD[0-1], ETHCRS_DV, ETHRX_ER to ETHREF_CLK rising edge set-up time 1.6 -- 2 -- ns 807 ETHREF_CLK rising edge to ETHRXD[0-1], ETHCRS_DV, ETHRX_ER hold time 1.6 -- 1.6 -- ns 811 ETHREF_CLK rising edge to ETHTXD[0-1], ETHTX_EN output delay. 3 12.5 3 11 ns ETHREF_CLK 806 807 ETHCRS_DV ETHRXD[0-1] ETHRX_ER Valid 811 ETHTX_EN ETHTXD[0-1] Valid Figure 2-20. Valid RMII Mode Signal Timing MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-23 Specifications 2.5.10.4 SMII Mode Table 2-26. No. SMII Mode Signal Timing Characteristics Min Max Unit 808 ETHSYNC_IN, ETHRXD to ETHCLOCK rising edge set-up time 1.0 -- ns 809 ETHCLOCK rising edge to ETHSYNC_IN, ETHRXD hold time 1.0 -- ns 810 ETHCLOCK rising edge to ETHSYNC, ETHTXD output delay * 1.1 V core. * 1.2 V core. 1.51 1.51 6.02 5.02 ns ns Notes: 1. 2. Measured using a 5 pF load. Measured using a 15 pF load. ETHCLOCK 808 809 ETHSYNC_IN ETHRXD Valid 810 ETHSYNC ETHTXD Valid Figure 2-21. Valid SMII Mode Signal Timing 2.5.11 GPIO Timing Table 2-27. GPIO Timing Ref = CLKIN No. Characteristics Ref = CLKOUT (1.2 V only) Unit Min Max Min Max 601 REFCLK edge to GPIO out valid (GPIO out delay time) -- 6.1 -- 6.9 ns 602 REFCLK edge to GPIO out not valid (GPIO out hold time) 1.1 -- 1.3 -- ns 603 REFCLK edge to high impedance on GPIO out -- 5.4 -- 6.2 ns 604 GPIO in valid to REFCLK edge (GPIO in set-up time) 3.5 -- 3.7 -- ns 605 REFCLK edge to GPIO in not valid (GPIO in hold time) 0.5 -- 0.5 -- ns MSC8122 Technical Data, Rev. 12 2-24 Freescale Semiconductor AC Timings REFCLK 601 603 602 GPIO (Output) High Impedance 604 605 GPIO (Input) Valid Figure 2-22. GPIO Timing 2.5.12 EE Signals Table 2-28. Number Notes: Characteristics 65 EE0 (input) 66 EE1 (output) 1. 2. EE Pin Timing Type Min Asynchronous 4 core clock periods Synchronous to Core clock 1 core clock period The core clock is the SC140 core clock. The ratio between the core clock and CLKOUT is configured during power-on-reset. Refer to Table 1-4 on page 1-6 for details on EE pin functionality. Figure 2-23 shows the signal behavior of the EE pins. 65 EE0 in 66 EE1 out Figure 2-23. EE Pin Timing Table 2-29. JTAG Timing 2.5.13 JTAG Signals No. Characteristics All frequencies Min Max Unit 700 TCK frequency of operation (1/(TC x 4); maximum 25 MHz) 0.0 25 MHz 701 TCK cycle time 40.0 -- ns 702 TCK clock pulse width measured at VM = 1.6 V * High * Low 20.0 16.0 -- -- ns ns TCK rise and fall times 0.0 3.0 ns 703 MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-25 Specifications Table 2-29. No. JTAG Timing (Continued) All frequencies Characteristics Min Unit Max 704 Boundary scan input data set-up time 5.0 -- ns 705 Boundary scan input data hold time 20.0 -- ns 706 TCK low to output data valid 0.0 30.0 ns 707 TCK low to output high impedance 0.0 30.0 ns 708 TMS, TDI data set-up time 5.0 -- ns 709 TMS, TDI data hold time 20.0 -- ns 710 TCK low to TDO data valid 0.0 20.0 ns 711 TCK low to TDO high impedance 0.0 20.0 ns 712 TRST assert time 100.0 -- ns 713 TRST set-up time to TCK low 30.0 -- ns Note: All timings apply to OnCE module data transfers as well as any other transfers via the JTAG port. 701 702 VM VIH TCK (Input) VM VIL 703 703 Figure 2-24. TCK (Input) Test Clock Input Timing Diagram VIH VIL 704 Data Inputs 705 Input Data Valid 706 Data Outputs Output Data Valid 707 Data Outputs Figure 2-25. Boundary Scan (JTAG) Timing Diagram MSC8122 Technical Data, Rev. 12 2-26 Freescale Semiconductor AC Timings TCK (Input) VIH VIL 708 TDI TMS (Input) 709 Input Data Valid 710 TDO (Output) Output Data Valid 711 TDO (Output) Figure 2-26. Test Access Port Timing Diagram TCK (Input) 713 TRST (Input) 712 Figure 2-27. TRST Timing Diagram MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 2-27 Specifications MSC8122 Technical Data, Rev. 12 2-28 Freescale Semiconductor 3 Packaging This section provides information on the MSC8122 package, including diagrams of the package pinouts and tables showing how the signals discussed in Chapter 1 are allocated. The MSC8122 is available in a 431-pin flip chipplastic ball grid array (FC-PBGA). 3.1 Package Description Figure 3-1 and Figure 3-2 show top and bottom views of the package, including pinouts. To conform to JEDEC requirements, the package is based on a 23 x 23 position (20 x 20 mm) layout with the outside perimeter depopulated. Therefore, ball position numbering starts with B2. Signal names shown in the figures are typically the signal assigned after reset. Signals that are only used during power-on reset (SWTE, DSISYNC, DSI64, MODCK[1-2], CNFGS, and CHIP_ID[0-3]) are not shown in these figures if there is another signal assigned to the pin after reset. Also, there are several signals that are designated as IRQ lines immediately after reset, but represent duplicate IRQ lines that should be reconfigured by the user. To represent these signals uniquely in the figures, the second functions (BADDR[29-31], DP[1-7], and INT_OUT) are used. Table 3-1 lists the MSC8122 signals alphabetically by signal name. Connections with multiple names are listed individually by each name. Signals with programmable polarity are shown both as signals which are asserted low (default) and high (that is, NAME/NAME). Table 3-2 lists the signals numerically by pin number. Each pin number is listed once with the various signals that are multiplexed to it. For simplicity, signals with programmable polarity are shown in this table only with their default name (asserted low). Note: For Ethernet signals multiplexed with the DSI/system Bus (MII and RMII modes only), signals not used by the RMII mode are reserved when the Ethernet controller is multiplexed with the DSI/system bus and RMII mode is selected. These reserved signals can be left unconnected. These RMII reserved signals are not included in Table 3-1, but are indicated in Table 3-2. Note: For Ethernet signals multiplexed with the GPIO/TDM signals, signals not used by the RMII or SMII mode can be assigned to their alternate GPIO or dedicated function, except for GPIO10 and GPIO14. If the Ethernet controller is enabled and multiplexed with the GPIO signals and SMII mode is selected, GPIO10 and GPIO14 (E21 and F21, respectively) must be left unconnected. These signals are designated as NC (no connect) in Table 3-1 and Table 3-2. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-1 Packaging Top View 2 B 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 VDD GND GND NMI_ OUT GND VDD GND VDD GND VDD GND VDD GND VDD GND VDD GPIO0 VDD VDD GND S GPIO28 HCID1 RESET GND VDD GND VDD GND VDD GND GND GPIO30 GPIO2 GPIO1 GPIO7 GPIO3 GPIO5 GPIO6 VDDH HCID3 GND VDD GND VDD GND VDD VDD GPIO31 GPIO29 VDDH GPIO4 VDDH GND GPIO8 GND VDD GND VDD GND VDD GND GND GND GPIO9 GPIO13 GPIO10 GPIO12 C GND VDD TDO D TDI EE0 EE1 TCK TRST TMS F PO RESET RST CONF NMI HA29 HA22 GND VDD VDD VDD GND VDD GND VDD ETHRX_ ETHTX_ GPIO20 GPIO18 GPIO16 GPIO11 GPIO14 GPIO19 CLK CLK G HA24 HA27 HA25 HA23 HA17 PWE0 VDD VDD BADDR 31 BM0 ABB VDD INT_ OUT ETHCR S VDD CS1 BCTL0 GPIO15 GND H HA20 HA28 VDD HA19 TEST PSD CAS PGTA VDD BM1 ARTRY AACK DBB HTA VDD TT4 CS4 GPIO24 GPIO21 VDD VDDH A31 J HA18 HA26 VDD HA13 GND PSDA BADDR MUX 27 VDD CLKIN BM2 DBG VDD GND VDD TT3 PSDA10 BCTL1 GPIO23 GND GPIO25 A30 K HA15 HA21 HA16 PWE3 PWE1 BADDR 30 Res. GND GND GND GND CLKOUT VDD TT2 ALE CS2 GND A26 A29 A28 L HA12 HA14 HA11 VDDH VDDH BADDR BADDR 28 29 GND GND GND VDDH GND GND CS3 VDDH A27 A25 A22 M HD28 HD31 VDDH GND GND GND VDD VDDH GND GND VDDH HB RST VDDH VDDH GND VDDH A24 A21 N HD26 HD30 HD29 HD24 PWE2 VDDH HWBS 0 HBCS GND GND HRDS BG HCS CS0 A23 A20 P HD20 HD27 HD25 HD23 HWBS 3 HWBS 2 HWBS HCLKIN 1 GND GND GND TA BR TEA PSD VAL DP0 VDDH GND A19 R HD18 VDDH GND HD22 HWBS 6 HWBS 4 TSZ1 TSZ3 GBL VDD VDD VDD TT0 DP7 DP6 DP3 TS DP2 A17 A18 A16 T HD17 HD21 HD1 HD0 HWBS 7 HWBS 5 TSZ0 TSZ2 TBST VDD D16 TT1 D21 D23 DP5 DP4 DP1 D30 GND A15 A14 U HD16 HD19 HD2 D2 D3 D6 D8 D9 D11 D14 D15 D17 D19 D22 D25 D26 D28 D31 VDDH A12 A13 V HD3 VDDH GND D0 D1 D4 D5 D7 D10 D12 D13 D18 D20 GND D24 D27 D29 A8 A9 A10 A11 W HD6 HD5 HD4 GND GND VDDH VDDH GND VDDH GND HD40 VDDH HD33 VDDH HD32 GND GND A7 A6 Y HD7 HD15 VDDH HD9 VDD HD60 HD58 GND VDDH HD51 GND VDDH HD43 GND VDDH GND HD37 HD34 VDDH A4 A5 AA VDD HD14 HD12 HD10 HD63 HD59 GND VDDH HD54 HD52 VDDH GND VDDH HD46 GND HD42 HD38 HD35 A0 A2 A3 AB GND HD13 HD11 HD8 HD62 HD61 HD57 HD56 HD55 HD53 HD50 HD49 HD48 HD47 HD45 HD44 HD41 HD39 HD36 A1 VDD E GND HCID2 HRESET GPIO27 HCID0 POE VDD GND GPIO17 GPIO22 M 81 SC 22 GNDSYN VCCSYN HDST1 HDST0 Figure 3-1. PSDWE GPIO26 MSC8122 Package, Top View MSC8122 Technical Data, Rev. 12 3-2 Freescale Semiconductor Package Description Bottom View 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 B GND VDD VDD GPIO0 VDD GND VDD GND VDD GND VDD GND VDD GND VDD GND NMI_ OUT GND GND VDD C GPIO6 GPIO5 GPIO3 GPIO7 GPIO1 GPIO2 GPIO30 GND GND VDD GND VDD GND VDD GND S RESET TDO VDD GND D GPIO8 GND VDDH GPIO4 VDDH GPIO29 GPIO31 VDD VDD GND VDD GND VDD GND HCID3 GND EE1 EE0 TDI GPIO12 GPIO10 GPIO13 GPIO9 GND GND GND VDD GND VDD GND VDD GND TMS TRST TCK ETHTX_ ETHRX_ CLK CLK VDD GND VDD GND VDD VDD VDD GND HA22 HA29 NMI RST CONF PO RESET E GND F GPIO19 GPIO14 GPIO11 GPIO16 GPIO18 GPIO20 HCID2 VDDH HCID0 GPIO27 HRESET GND GPIO15 BCTL0 CS1 VDD ETHCR S INT_ OUT VDD ABB BM0 BADDR 31 VDD VDD PWE0 HA17 HA23 HA25 HA27 HA24 CS4 TT4 VDD HTA DBB AACK ARTRY BM1 VDD PGTA PSD CAS TEST HA19 VDD HA28 HA20 TT3 VDD GND VDD DBG BM2 CLKIN VDD BADDR PSDA 27 MUX GND HA13 VDD HA26 HA18 CLKOUT GND GND GND GND Res. BADDR 30 PWE1 PWE3 HA16 HA21 HA15 GND GND BADDR BADDR 29 28 VDDH VDDH HA11 HA14 HA12 GND VDDH VDD GND GND GND VDDH HD31 HD28 GND HBCS HWBS 0 VDDH PWE2 HD24 HD29 HD30 HD26 GND HCLKIN HWBS 1 HWBS 2 HWBS 3 HD23 HD25 HD27 HD20 A31 VDDH VDD GPIO21 GPIO24 J A30 GPIO25 GND GPIO23 BCTL1 PSDA10 K A28 A29 A26 GND CS2 ALE TT2 VDD L A22 A25 A27 VDDH CS3 GND GND VDDH GND M A21 A24 VDDH GND VDDH VDDH HB RST VDDH GND N A20 A23 CS0 HCS BG HRDS GND P A19 GND VDDH DP0 PSD VAL TEA BR TA GND GND R A16 A18 A17 DP2 TS DP3 DP6 DP7 TT0 VDD VDD VDD GBL TSZ3 TSZ1 HWBS 4 HWBS 6 HD22 GND VDDH HD18 T A14 A15 GND D30 DP1 DP4 DP5 D23 D21 TT1 D16 VDD TBST TSZ2 TSZ0 HWBS 5 HWBS 7 HD0 HD1 HD21 HD17 U A13 A12 VDDH D31 D28 D26 D25 D22 D19 D17 D15 D14 D11 D9 D8 D6 D3 D2 HD2 HD19 HD16 V A11 A10 A9 A8 D29 D27 D24 GND D20 D18 D13 D12 D10 D7 D5 D4 D1 D0 GND VDDH HD3 W A6 A7 GND GND HD32 VDDH HD33 VDDH HD40 GND VDDH GND VDDH VDDH GND GND HD4 HD5 HD6 Y A5 A4 VDDH HD34 HD37 GND VDDH GND HD43 VDDH GND HD51 VDDH GND HD58 HD60 VDD HD9 VDDH HD15 HD7 AA A3 A2 A0 HD35 HD38 HD42 GND HD46 VDDH GND VDDH HD52 HD54 VDDH GND HD59 HD63 HD10 HD12 HD14 VDD AB VDD A1 HD36 HD39 HD41 HD44 HD45 HD47 HD48 HD49 HD50 HD53 HD55 HD56 HD57 HD61 HD62 HD8 HD11 HD13 GND GPIO26 PSDWE POE SC 81 22 H M G GPIO22 GPIO17 VDD HCID1 GPIO28 2 Figure 3-2. VCCSYN GNDSYN HDST0 HDST1 MSC8122 Package, Bottom View MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-3 Packaging Table 3-1. MSC8122 Signal Listing By Name Signal Name Location Designator Signal Name Location Designator A0 AA20 BADDR27 J8 A1 AB21 BADDR28 L7 A2 AA21 BADDR29 L8 A3 AA22 BADDR30 K8 A4 Y21 BADDR31 G10 A5 Y22 BCTL0 G18 A6 W22 BCTL1 J18 A7 W21 BG N16 A8 V19 BNKSEL0 G11 A9 V20 BNKSEL1 H10 A10 V21 BNKSEL2 J11 A11 V22 BM0 G11 A12 U21 BM1 H10 A13 U22 BM2 J11 A14 T22 BR P16 A15 T21 CHIP_ID0 B19 A16 R22 CHIP_ID1 C18 A17 R20 CHIP_ID2 C17 A18 R21 CHIP_ID3 D17 A19 P22 CLKIN J10 A20 N22 CLKOUT K14 A21 M22 CNFGS W3 A22 L22 CS0 N18 A23 N21 CS1 G17 A24 M21 CS2 K18 A25 L21 CS3 L18 A26 K20 CS4 H17 A27 L20 CS5 K16 A28 K22 CS5 J18 A29 K21 CS6 J16 A30 J22 CS7 H16 A31 H22 D0 V5 AACK H12 D1 V6 ABB G12 D2 U5 ALE K17 D3 U6 ARTRY H11 D4 V7 MSC8122 Technical Data, Rev. 12 3-4 Freescale Semiconductor Package Description Table 3-1. MSC8122 Signal Listing By Name (Continued) Signal Name Location Designator Signal Name Location Designator D5 V8 D41 AB18 D6 U7 D42 AA17 D7 V9 D43 Y14 D8 U8 D44 AB17 D9 U9 D45 AB16 D10 V10 D46 AA15 D11 U10 D47 AB15 D12 V11 D48 AB14 D13 V12 D49 AB13 D14 U11 D50 AB12 D15 U12 D51 Y11 D16 T12 D52 AA11 D17 U13 D53 AB11 D18 V13 D54 AA10 D19 U14 D55 AB10 D20 V14 D56 AB9 D21 T14 D57 AB8 D22 U15 D58 Y8 D23 T15 D59 AA7 D24 V16 D60 Y7 D25 U16 D61 AB7 D26 U17 D62 AB6 D27 V17 D63 AA6 D28 U18 DACK1 G21 D29 V18 DACK1 T18 D30 T19 DACK2 F22 D31 U19 DACK2 R19 D32 W18 DACK3 T17 D33 W16 DACK4 T16 D34 Y19 DBB H13 D35 AA19 DBG J12 D36 AB20 DONE1 F19 D37 Y18 DONE2 G22 D38 AA18 DP0 P19 D39 AB19 DP1 T18 D40 W14 DP2 R19 MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-5 Packaging Table 3-1. MSC8122 Signal Listing By Name (Continued) Signal Name Location Designator Signal Name Location Designator DP3 R17 ETHRXD0 F21 DP4 T17 ETHRXD0 W14 DP5 T16 ETHRXD1 E22 DP6 R16 ETHRXD1 AB18 DP7 R15 ETHRXD2 C22 DRACK1 F19 ETHRXD2 AA17 DRACK2 G22 ETHRXD3 C21 DREQ1 E6 ETHRXD3 Y14 DREQ1 G19 ETHSYNC E22 DREQ1 P19 ETHSYNC_IN F15 DREQ2 C6 ETHTX_CLK F16 DREQ2 F18 ETHTX_EN D17 DREQ2 R17 ETHTX_EN AA10 DREQ3 R16 ETHTX_ER D19 DREQ4 R15 ETHTX_ER AB10 DSI64 U4 ETHTXD F20 DSISYNC T4 ETHTXD0 B19 EE0 D3 ETHTXD0 AA15 EE1 D4 ETHTXD1 C18 ETHCLOCK F16 ETHTXD1 AB15 ETHCOL D22 ETHTXD2 C20 ETHCOL Y7 ETHTXD2 AB14 ETHCRS G15 ETHTXD3 C19 ETHCRS_DV E21 ETHTXD3 AB13 ETHCRS_DV AB9 EXT_BG2 T18 ETHMDC E20 EXT_BG3 T16 ETHMDC Y8 EXT_BR2 P19 ETHMDIO E19 EXT_BR3 R17 ETHMDIO AA7 EXT_DBG2 R19 ETHREF_CLK F16 EXT_DBG3 T17 ETHRX_CLK F15 GBL R10 ETHRX_DV E21 GND B4 ETHRX_DV AB9 GND B5 ETHRX_ER F20 GND B7 ETHRX_ER AB8 GND B9 ETHRXD G15 GND B11 MSC8122 Technical Data, Rev. 12 3-6 Freescale Semiconductor Package Description Table 3-1. MSC8122 Signal Listing By Name (Continued) Signal Name Location Designator Signal Name Location Designator GND B13 GND L14 GND B15 GND L16 GND B17 GND L17 GND B22 GND M5 GND C2 GND M6 GND C8 GND M7 GND C10 GND M10 GND C12 GND M14 GND C14 GND M19 GND C15 GND N10 GND D5 GND N14 GND D9 GND P10 GND D11 GND P13 GND D13 GND P14 GND D21 GND P21 GND E8 GND R4 GND E10 GND T20 GND E12 GND V4 GND E14 GND V15 GND E15 GND W5 GND E17 GND W6 GND E18 GND W9 GND F7 GND W13 GND F11 GND W19 GND F13 GND W20 GND G20 GND Y9 GND J6 GND Y12 GND J14 GND Y15 GND J20 GND Y17 GND K10 GND AA8 GND K11 GND AA13 GND K12 GND AA16 GND K13 GND AB2 GND K19 GNDSYN P11 GND L9 GPIO0 B19 GND L10 GPIO1 C18 MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-7 Packaging Table 3-1. MSC8122 Signal Listing By Name (Continued) Signal Name Location Designator Signal Name Location Designator GPIO2 C17 HA13 J5 GPIO3 C20 HA14 L3 GPIO4 D19 HA15 K2 GPIO5 C21 HA16 K4 GPIO6 C22 HA17 G6 GPIO7 C19 HA18 J2 GPIO8 D22 HA19 H5 GPIO9 E19 HA20 H2 GPIO10 E21 HA21 K3 GPIO11 F20 HA22 F6 GPIO12 E22 HA23 G5 GPIO13 E20 HA24 G2 GPIO14 F21 HA25 G4 GPIO15 G19 HA26 J3 GPIO16 F19 HA27 G3 GPIO17 G21 HA28 H3 GPIO18 F18 HA29 F5 GPIO19 F22 HBCS N9 GPIO20 F17 HBRST M16 GPIO21 H19 HCID0 E7 GPIO22 G22 HCID1 C7 GPIO23 J19 HCID2 D7 GPIO24 H18 HCID3 D8 GPIO25 J21 HCLKIN P9 GPIO26 N20 HCS N17 GPIO27 E6 HD0 T5 GPIO28 C6 HD1 T4 GPIO29 D17 HD2 U4 GPIO30 C16 HD3 V2 GPIO31 D16 HD4 W4 HA7 R14 HD5 W3 HA8 D8 HD6 W2 HA9 W11 HD7 Y2 HA10 W10 HD8 AB5 HA11 L4 HD9 Y5 HA12 L2 HD10 AA5 MSC8122 Technical Data, Rev. 12 3-8 Freescale Semiconductor Package Description Table 3-1. MSC8122 Signal Listing By Name (Continued) Signal Name Location Designator Signal Name Location Designator HD11 AB4 HD47 AB15 HD12 AA4 HD48 AB14 HD13 AB3 HD49 AB13 HD14 AA3 HD50 AB12 HD15 Y3 HD51 Y11 HD16 U2 HD52 AA11 HD17 T2 HD53 AB11 HD18 R2 HD54 AA10 HD19 U3 HD55 AB10 HD20 P2 HD56 AB9 HD21 T3 HD57 AB8 HD22 R5 HD58 Y8 HD23 P5 HD59 AA7 HD24 N5 HD60 Y7 HD25 P4 HD61 AB7 HD26 N2 HD62 AB6 HD27 P3 HD63 AA6 HD28 M2 HDBE0 N8 HD29 N4 HDBE1 P8 HD30 N3 HDBE2 P7 HD31 M3 HDBE3 P6 HD32 W18 HDBE4 R7 HD33 W16 HDBE5 T7 HD34 Y19 HDBE6 R6 HD35 AA19 HDBE7 T6 HD36 AB20 HDBS0 N8 HD37 Y18 HDBS1 P8 HD38 AA18 HDBS2 P7 HD39 AB19 HDBS3 P6 HD40 W14 HDBS4 R7 HD41 AB18 HDBS5 T7 HD42 AA17 HDBS6 R6 HD43 Y14 HDBS7 T6 HD44 AB17 HDST0 W11 HD45 AB16 HDST1 W10 HD46 AA15 HRDE N15 MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-9 Packaging Table 3-1. MSC8122 Signal Listing By Name (Continued) Signal Name Location Designator Signal Name Location Designator HRDS N15 IRQ5 H13 HRESET E5 IRQ5 L8 HRW N15 IRQ5 T16 HTA H14 IRQ6 C17 HWBE0 N8 IRQ6 D22 HWBE1 P8 IRQ6 R16 HWBE2 P7 IRQ7 E19 HWBE3 P6 IRQ7 G14 HWBE4 R7 IRQ7 R15 HWBE5 T7 IRQ8 E21 HWBE6 R6 IRQ9 F20 HWBE7 T6 IRQ10 E22 HWBS0 N8 IRQ11 E20 HWBS1 P8 IRQ12 F21 HWBS2 P7 IRQ13 J19 HWBS3 P6 IRQ14 H18 HWBS4 R7 IRQ15 J21 HWBS5 T7 MODCK1 V2 HWBS6 R6 MODCK2 W4 HWBS7 T6 NC E21 INT_OUT G14 NC F21 IRQ1 C20 NMI F4 IRQ1 R10 NMI_OUT B6 IRQ1 T18 PBS0 G7 IRQ2 D19 PBS1 K6 IRQ2 K8 PBS2 N6 IRQ2 R19 PBS3 K5 IRQ3 C21 PBS4 R7 IRQ3 G10 PBS5 T7 IRQ3 R17 PBS6 R6 IRQ4 B19 PBS7 T6 IRQ4 C22 PGPL0 J17 IRQ4 G12 PGPL1 N19 IRQ4 T17 PGPL2 K7 IRQ5 C18 PGPL3 H7 IRQ5 C19 PGPL4 H8 MSC8122 Technical Data, Rev. 12 3-10 Freescale Semiconductor Package Description Table 3-1. MSC8122 Signal Listing By Name (Continued) Signal Name Location Designator Signal Name Location Designator PGPL5 J7 TC0 G11 PGTA H8 TC1 H10 POE K7 TC2 J11 PORESET F2 TCK E2 PPBS H8 TDI D2 PSDA10 J17 TDM0RCLK J21 PSDAMUX J7 TDM0RDAT N20 PSDCAS H7 TDM0RSYN H18 PSDDQM0 G7 TDM0TCLK G22 PSDDQM1 K6 TDM0TDAT J19 PSDDQM2 N6 TDM0TSYN H19 PSDDQM3 K5 TDM1RCLK F22 PSDDQM4 R7 TDM1RDAT F17 PSDDQM5 T7 TDM1RSYN F18 PSDDQM6 R6 TDM1TCLK F19 PSDDQM7 T6 TDM1TDAT G21 PSDRAS K7 TDM1TSYN G19 PSDVAL P18 TDM2RCLK E20 PSDWE N19 TDM2RDAT F21 PWE0 G7 TDM2RSYN E22 PWE1 K6 TDM2TCLK E21 PWE2 N6 TDM2TDAT F20 PWE3 K5 TDM2TSYN E19 PWE4 R7 TDM3RCLK C19 PWE5 T7 TDM3RDAT D22 PWE6 R6 TDM3RSYN C22 PWE7 T6 TDM3TCLK D19 PUPMWAIT H8 TDM3TDAT C21 Reserved K9 TDM3TSYN C20 RSTCONF F3 TDO C4 SCL D16 TEA P17 SDA C16 TEST H6 SRESET C5 TIMER0 C18 SWTE T5 TIMER1 C17 TA P15 TIMER2 C16 TBST T10 TIMER3 D16 MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-11 Packaging Table 3-1. MSC8122 Signal Listing By Name (Continued) Signal Name Location Designator Signal Name Location Designator TMCLK C16 VDD F8 TMS E4 VDD F9 TRST E3 VDD F10 TS R18 VDD F12 TSZ0 T8 VDD F14 TSZ1 R8 VDD G8 TSZ2 T9 VDD G9 TSZ3 R9 VDD G13 TT0 R14 VDD G16 TT1 T13 VDD H4 TT2 K16 VDD H9 TT3 J16 VDD H15 TT4 H16 VDD H20 URXD E6 VDD J4 UTXD C6 VDD J9 VCCSYN P12 VDD J13 VDD B8 VDD J15 VDD B10 VDD K15 VDD B12 VDD M8 VDD B14 VDD R11 VDD B16 VDD R12 VDD B18 VDD R13 VDD B20 VDD T11 VDD B21 VDD Y6 VDD C3 VDD AA2 VDD C9 VDD B3 VDD C11 VDD AB22 VDD C13 VDDH D6 VDD D10 VDDH D18 VDD D12 VDDH D20 VDD D14 VDDH H21 VDD D15 VDDH L5 VDD E9 VDDH L6 VDD E11 VDDH L15 VDD E13 VDDH L19 VDD E16 VDDH M4 MSC8122 Technical Data, Rev. 12 3-12 Freescale Semiconductor Package Description Table 3-1. MSC8122 Signal Listing By Name (Continued) Signal Name Location Designator Signal Name Location Designator VDDH M9 VDDH W12 VDDH M15 VDDH W15 VDDH M17 VDDH W17 VDDH M18 VDDH Y4 VDDH M20 VDDH Y10 VDDH N7 VDDH Y13 VDDH P20 VDDH Y16 VDDH R3 VDDH Y20 VDDH U20 VDDH AA9 VDDH V3 VDDH AA12 VDDH W7 VDDH AA14 VDDH W8 Note: This table lists every signal name. Because many signals are multiplexed, an individual ball designator number may be listed several times. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-13 Packaging Table 3-2. MSC8122 Signal Listing by Ball Designator Des. Signal Name Des. Signal Name B3 VDD C18 GPIO1/TIMER0/CHIP_ID1/IRQ5/ETHTXD1 B4 GND C19 GPIO7/TDM3RCLK/IRQ5/ETHTXD3 B5 GND C20 GPIO3/TDM3TSYN/IRQ1/ETHTXD2 B6 NMI_OUT C21 GPIO5/TDM3TDAT/IRQ3/ETHRXD3 B7 GND C22 GPIO6/TDM3RSYN/IRQ4/ETHRXD2 B8 VDD D2 TDI B9 GND D3 EE0 B10 VDD D4 EE1 B11 GND D5 GND B12 VDD D6 VDDH B13 GND D7 HCID2 B14 VDD D8 HCID3/HA8 B15 GND D9 GND B16 VDD D10 VDD B17 GND D11 GND B18 VDD D12 VDD B19 GPIO0/CHIP_ID0/IRQ4/ETHTXD0 D13 GND B20 VDD D14 VDD B21 VDD D15 VDD B22 GND D16 GPIO31/TIMER3/SCL C2 GND D17 GPIO29/CHIP_ID3/ETHTX_EN C3 VDD D18 VDDH C4 TDO D19 GPIO4/TDM3TCLK/IRQ2/ETHTX_ER C5 SRESET D20 VDDH C6 GPIO28/UTXD/DREQ2 D21 GND C7 HCID1 D22 GPIO8/TDM3RDAT/IRQ6/ETHCOL C8 GND E2 TCK C9 VDD E3 TRST C10 GND E4 TMS C11 VDD E5 HRESET C12 GND E6 GPIO27/URXD/DREQ1 C13 VDD E7 HCID0 C14 GND E8 GND C15 GND E9 VDD C16 GPIO30/TIMER2/TMCLK/SDA E10 GND C17 GPIO2/TIMER1/CHIP_ID2/IRQ6 E11 VDD MSC8122 Technical Data, Rev. 12 3-14 Freescale Semiconductor Package Description Table 3-2. MSC8122 Signal Listing by Ball Designator (Continued) Des. Signal Name Des. Signal Name E12 GND G6 HA17 E13 VDD G7 PWE0/PSDDQM0/PBS0 E14 GND G8 VDD E15 GND G9 VDD E16 VDD G10 IRQ3/BADDR31 E17 GND G11 BM0/TC0/BNKSEL0 E18 GND G12 ABB/IRQ4 E19 GPIO9/TDM2TSYN/IRQ7/ETHMDIO G13 VDD E20 GPIO13/TDM2RCLK/IRQ11/ETHMDC G14 IRQ7/INT_OUT E21 GPIO10/TDM2TCLK/IRQ8/ETHRX_DV/ETHCRS_DV/NC G15 ETHCRS/ETHRXD E22 GPIO12/TDM2RSYN/IRQ10/ETHRXD1/ETHSYNC G16 VDD F2 PORESET G17 CS1 F3 RSTCONF G18 BCTL0 F4 NMI G19 GPIO15/TDM1TSYN/DREQ1 F5 HA29 G20 GND F6 HA22 G21 GPIO17/TDM1TDAT/DACK1 F7 GND G22 GPIO22/TDM0TCLK/DONE2/DRACK2 F8 VDD H2 HA20 F9 VDD H3 HA28 F10 VDD H4 VDD F11 GND H5 HA19 F12 VDD H6 TEST F13 GND H7 PSDCAS/PGPL3 F14 VDD H8 PGTA/PUPMWAIT/PGPL4/PPBS F15 ETHRX_CLK/ETHSYNC_IN H9 VDD F16 ETHTX_CLK/ETHREF_CLK/ETHCLOCK H10 BM1/TC1/BNKSEL1 F17 GPIO20/TDM1RDAT H11 ARTRY F18 GPIO18/TDM1RSYN/DREQ2 H12 AACK F19 GPIO16/TDM1TCLK/DONE1/DRACK1 H13 DBB/IRQ5 F20 GPIO11/TDM2TDAT/IRQ9/ETHRX_ER/ETHTXD H14 HTA F21 GPIO14/TDM2RDAT/IRQ12/ETHRXD0/NC H15 VDD F22 GPIO19/TDM1RCLK/DACK2 H16 TT4/CS7 G2 HA24 H17 CS4 G3 HA27 H18 GPIO24/TDM0RSYN/IRQ14 G4 HA25 H19 GPIO21/TDM0TSYN G5 HA23 H20 VDD MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-15 Packaging Table 3-2. MSC8122 Signal Listing by Ball Designator (Continued) Des. Signal Name Des. Signal Name H21 VDDH K15 VDD H22 A31 K16 TT2/CS5 J2 HA18 K17 ALE J3 HA26 K18 CS2 J4 VDD K19 GND J5 HA13 K20 A26 J6 GND K21 A29 J7 PSDAMUX/PGPL5 K22 A28 J8 BADDR27 L2 HA12 J9 VDD L3 HA14 J10 CLKIN L4 HA11 J11 BM2/TC2/BNKSEL2 L5 VDDH J12 DBG L6 VDDH J13 VDD L7 BADDR28 J14 GND L8 IRQ5/BADDR29 J15 VDD L9 GND J16 TT3/CS6 L10 GND J17 PSDA10/PGPL0 L14 GND J18 BCTL1/CS5 L15 VDDH J19 GPIO23/TDM0TDAT/IRQ13 L16 GND J20 GND L17 GND J21 GPIO25/TDM0RCLK/IRQ15 L18 CS3 J22 A30 L19 VDDH K2 HA15 L20 A27 K3 HA21 L21 A25 K4 HA16 L22 A22 K5 PWE3/PSDDQM3/PBS3 M2 HD28 K6 PWE1/PSDDQM1/PBS1 M3 HD31 K7 POE/PSDRAS/PGPL2 M4 VDDH K8 IRQ2/BADDR30 M5 GND K9 Reserved M6 GND K10 GND M7 GND K11 GND M8 VDD K12 GND M9 VDDH K13 GND M10 GND K14 CLKOUT M14 GND MSC8122 Technical Data, Rev. 12 3-16 Freescale Semiconductor Package Description Table 3-2. MSC8122 Signal Listing by Ball Designator (Continued) Des. Signal Name Des. Signal Name M15 VDDH P12 VCCSYN M16 HBRST P13 GND M17 VDDH P14 GND M18 VDDH P15 TA M19 GND P16 BR M20 VDDH P17 TEA M21 A24 P18 PSDVAL M22 A21 P19 DP0/DREQ1/EXT_BR2 N2 HD26 P20 VDDH N3 HD30 P21 GND N4 HD29 P22 A19 N5 HD24 R2 HD18 N6 PWE2/PSDDQM2/PBS2 R3 VDDH N7 VDDH R4 GND N8 HWBS0/HDBS0/HWBE0/HDBE0 R5 HD22 N9 HBCS R6 HWBS6/HDBS6/HWBE6/HDBE6/PWE6/PSDDQM6/PBS6 N10 GND R7 HWBS4/HDBS4/HWBE4/HDBE4/PWE4/PSDDQM4/PBS4 N14 GND R8 TSZ1 N15 HRDS/HRW/HRDE R9 TSZ3 N16 BG R10 IRQ1/GBL N17 HCS R11 VDD N18 CS0 R12 VDD N19 PSDWE/PGPL1 R13 VDD N20 GPIO26/TDM0RDAT R14 TT0/HA7 N21 A23 R15 IRQ7/DP7/DREQ4 N22 A20 R16 IRQ6/DP6/DREQ3 P2 HD20 R17 IRQ3/DP3/DREQ2/EXT_BR3 P3 HD27 R18 TS P4 HD25 R19 IRQ2/DP2/DACK2/EXT_DBG2 P5 HD23 R20 A17 P6 HWBS3/HDBS3/HWBE3/HDBE3 R21 A18 P7 HWBS2/HDBS2/HWBE2/HDBE2 R22 A16 P8 HWBS1/HDBS1/HWBE1/HDBE1 T2 HD17 P9 HCLKIN T3 HD21 P10 GND T4 HD1/DSISYNC P11 GNDSYN T5 HD0/SWTE MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-17 Packaging Table 3-2. MSC8122 Signal Listing by Ball Designator (Continued) Des. Signal Name Des. Signal Name T6 HWBS7/HDBS7/HWBE7/HDBE7/PWE7/PSDDQM7/PBS7 U21 A12 T7 HWBS5/HDBS5/HWBE5/HDBE5/PWE5/PSDDQM5/PBS5 U22 A13 T8 TSZ0 V2 HD3/MODCK1 T9 TSZ2 V3 VDDH T10 TBST V4 GND T11 VDD V5 D0 T12 D16 V6 D1 T13 TT1 V7 D4 T14 D21 V8 D5 T15 D23 V9 D7 T16 IRQ5/DP5/DACK4/EXT_BG3 V10 D10 T17 IRQ4/DP4/DACK3/EXT_DBG3 V11 D12 T18 IRQ1/DP1/DACK1/EXT_BG2 V12 D13 T19 D30 V13 D18 T20 GND V14 D20 T21 A15 V15 GND T22 A14 V16 D24 U2 HD16 V17 D27 U3 HD19 V18 D29 U4 HD2/DSI64 V19 A8 U5 D2 V20 A9 U6 D3 V21 A10 U7 D6 V22 A11 U8 D8 W2 HD6 U9 D9 W3 HD5/CNFGS U10 D11 W4 HD4/MODCK2 U11 D14 W5 GND U12 D15 W6 GND U13 D17 W7 VDDH U14 D19 W8 VDDH U15 D22 W9 GND U16 D25 W10 HDST1/HA10 U17 D26 W11 HDST0/HA9 U18 D28 W12 VDDH U19 D31 W13 GND U20 VDDH W14 HD40/D40/ETHRXD0 MSC8122 Technical Data, Rev. 12 3-18 Freescale Semiconductor Package Description Table 3-2. MSC8122 Signal Listing by Ball Designator (Continued) Des. Signal Name Des. Signal Name W15 VDDH AA9 VDDH W16 HD33/D33/reserved AA10 HD54/D54/ETHTX_EN W17 VDDH AA11 HD52/D52 W18 HD32/D32/reserved AA12 VDDH W19 GND AA13 GND W20 GND AA14 VDDH W21 A7 AA15 HD46/D46/ETHTXT0 W22 A6 AA16 GND Y2 HD7 AA17 HD42/D42/ETHRXD2/reserved Y3 HD15 AA18 HD38/D38/reserved Y4 VDDH AA19 HD35/D35/reserved Y5 HD9 AA20 A0 Y6 VDD AA21 A2 Y7 HD60/D60/ETHCOL/reserved AA22 A3 Y8 HD58/D58/ETHMDC AB2 GND Y9 GND AB3 HD13 Y10 VDDH AB4 HD11 Y11 HD51/D51 AB5 HD8 Y12 GND AB6 HD62/D62 Y13 VDDH AB7 HD61/D61 Y14 HD43/D43/ETHRXD3/reserved AB8 HD57/D57/ETHRX_ER Y15 GND AB9 HD56/D56/ETHRX_DV/ETHCRS_DV Y16 VDDH AB10 HD55/D55/ETHTX_ER/reserved Y17 GND AB11 HD53/D53 Y18 HD37/D37/reserved AB12 HD50/D50 Y19 HD34/D34/reserved AB13 HD49/D49/ETHTXD3/reserved Y20 VDDH AB14 HD48/D48/ETHTXD2/reserved Y21 A4 AB15 HD47/D47/ETHTXD1 Y22 A5 AB16 HD45/D45 AA2 VDD AB17 HD44/D44 AA3 HD14 AB18 HD41/D41/ETHRXD1 AA4 HD12 AB19 HD39/D39/reserved AA5 HD10 AB20 HD36/D36/reserved AA6 HD63/D63 AB21 A1 AA7 HD59/D59/ETHMDIO AB22 VDD AA8 GND MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 3-19 Packaging 3.2 MSC8122 Package Mechanical Drawing Notes: 1. All dimensions in millimeters. 2. Dimensioning and tolerancing per ASME Y14.5M-1994. 3. Features are symmetrical about the package center lines unless dimensioned otherwise. 4. Maximum solder ball diameter measured parallel to Datum A. 5. Datum A, the seating plane, is determined by the spherical crowns of the solder balls. 6. Parallelism measurement shall exclude any effect of mark on top surface of package. 7. Capacitors may not be present on all devices. 8. Caution must be taken not to short capacitors or exposed metal capacitor pads on package top. 9. FC CBGA (Ceramic) package code: 5238. FC PBGA (Plastic) package code: 5263. 10.Pin 1 indicator can be in the form of number 1 marking or an "L" shape marking. Figure 3-3. MSC8122 Mechanical Information, 431-pin FC-PBGA Package MSC8122 Technical Data, Rev. 12 3-20 Freescale Semiconductor Design Considerations 4 The following sections discuss areas to consider when the MSC8122 device is designed into a system. 4.1 Start-up Sequencing Recommendations Use the following guidelines for start-up and power-down sequences: * Assert PORESET and TRST before applying power and keep the signals driven low until the power reaches the required minimum power levels. This can be implemented via weak pull-down resistors. * CLKIN can be held low or allowed to toggle during the beginning of the power-up sequence. However, CLKIN must start toggling before the deassertion of PORESET and after both power supplies have reached nominal voltage levels. * If possible, bring up VDD/VCCSYN and VDDH together. If it is not possible, raise VDD/VCCSYN first and then bring up VDDH. VDDH should not exceed VDD/VCCSYN until VDD/VCCSYN reaches its nominal voltage level. Similarly, bring both voltage levels down together. If that is not possible reverse the power-up sequence, with VDDH going down first and then VDD/VCCSYN. Note: This recommended power sequencing for the MSC8122 is different from the MSC8102. External voltage applied to any input line must not exceed the I/O supply VDDH by more than 0.8 V at any time, including during power-up. Some designs require pull-up voltages applied to selected input lines during power-up for configuration purposes. This is an acceptable exception to the rule. However, each such input can draw up to 80 mA per input pin per device in the system during start-up. After power-up, VDDH must not exceed VDD/VCCSYN by more than 2.6 V. 4.2 Power Supply Design Considerations When used as a drop-in replacement in MSC8102 applications or when implementing a new design, use the guidelines described in Migrating Designs from the MSC8102 to the MSC8122 (AN2716) and the MSC8122 Design Checklist (AN2787) for optimal system performance. MSC8122 and MSC8126 Power Circuit Design Recommendations and Examples (AN2937) provides detailed design information. Figure 4-1 shows the recommended power decoupling circuit for the core power supply. The voltage regulator and the decoupling capacitors should supply the required device current without any drop in voltage on the device pins. The voltage on the package pins should not drop below the minimum specified voltage level even for a very short spikes. This can be achieved by using the following guidelines: * For the core supply, use a voltage regulator rated at 1.2 V with nominal rating of at least 3 A. This rating does not reflect actual average current draw, but is recommended because it resists changes imposed by transient spikes and has better voltage recovery time than supplies with lower current ratings. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 4-1 Design Considerations * Decouple the supply using low-ESR capacitors mounted as close as possible to the socket. Figure 4-1 shows three capacitors in parallel to reduce the resistance. Three capacitors is a recommended minimum number. If possible, mount at least one of the capacitors directly below the MSC8122 device. Maximum IR drop of 15 mV at 1 A Lmax = 2 cm 1.2 V Power supply or Voltage Regulator (Imin = 3 A) One 0.01 F capacitor for every 3 core supply pads. + - MSC8122 Bulk/Tantalum capacitors with low ESR and ESL High frequency capacitors (very low ESR and ESL) Note: Use at least three capacitors. Each capacitor must be at least 150 F. Figure 4-1. Core Power Supply Decoupling Each VCC and VDD pin on the MSC8122 device should have a low-impedance path to the board power supply. Similarly, each GND pin should have a low-impedance path to the ground plane. The power supply pins drive distinct groups of logic on the chip. The VCC power supply should have at least four 0.1 F by-pass capacitors to ground located as closely as possible to the four sides of the package. The capacitor leads and associated printed circuit traces connecting to chip VCC, VDD, and GND should be kept to less than half an inch per capacitor lead. A four-layer board is recommended, employing two inner layers as VCC and GND planes. All output pins on the MSC8122 have fast rise and fall times. PCB trace interconnection length should be minimized to minimize undershoot and reflections caused by these fast output switching times. This recommendation particularly applies to the address and data buses. Maximum PCB trace lengths of six inches are recommended. For the DSI control signals in synchronous mode, ensure that the layout supports the DSI AC timing requirements and minimizes any signal crosstalk. Capacitance calculations should consider all device loads as well as parasitic capacitances due to the PCB traces. Attention to proper PCB layout and bypassing becomes especially critical in systems with higher capacitive loads because these loads create higher transient currents in the VCC, VDD, and GND circuits. Pull up all unused inputs or signals that will be inputs during reset. Special care should be taken to minimize the noise levels on the PLL supply pins. There is one pair of PLL supply pins: VCCSYN-GNDSYN. To ensure internal clock stability, filter the power to the VCCSYN input with a circuit similar to the one in Figure 4-2. For optimal noise filtering, place the circuit as close as possible to VCCSYN. The 0.01-F capacitor should be closest to VCCSYN, followed by the 10-F capacitor, the 10-nH inductor, and finally the 10- resistor to VDD. These traces should be kept short and direct. Provide an extremely low impedance path to the ground plane for GNDSYN. Bypass GNDSYN to VCCSYN by a 0.01-F capacitor located as close as possible to the chip package. For best results, place this capacitor on the backside of the PCB aligned with the depopulated void on the MSC8122 located in the square defined by positions, L11, L12, L13, M11, M12, M13, N11, N12, and N13. VCCSYN VDD 10 10nH 10 F Figure 4-2. 0.01 F VCCSYN Bypass MSC8122 Technical Data, Rev. 12 4-2 Freescale Semiconductor Connectivity Guidelines 4.3 Connectivity Guidelines Unused output pins can be disconnected, and unused input pins should be connected to the non-active value, via resistors to VDDH or GND, except for the following: * If the DSI is unused (DDR[DSIDIS] is set), HCS and HBCS must pulled up and all the rest of the DSI signals can be disconnected. * When the DSI uses synchronous mode, HTA must be pulled up. In asynchronous mode, HTA should be pulled either up or down, depending on design requirements. * HDST can be disconnected if the DSI is in big-endian mode, or if the DSI is in little-endian mode and the DCR[DSRFA] bit is set. * When the DSI is in 64-bit data bus mode and DCR[BEM] is cleared, pull up HWBS[1-3]/HDBS[1-3]/HWBE[1-3]/ HDBE[1-3] and HWBS[4-7]/HDBS[4-7]/HWBE[4-7]/HDBE[4-7]/PWE[4-7]/PSDDQM[4-7]/PBS[4-7]. * When the DSI is in 32-bit data bus mode and DCR[BEM] is cleared, must be pulled up. HWBS[1-3]/HDBS[1-3]/HWBE[1-3]/HDBE[1-3] * When the DSI is in asynchronous mode, HBRST and HCLKIN should either be disconnected or pulled up. * The following signals must be pulled up: HRESET, SRESET, ARTRY, TA, TEA, PSDVAL, and AACK. * In single-master mode (BCR[EBM] = 0) with internal arbitration (PPC_ACR[EARB] = 0): -- BG, DBG, and TS can be left unconnected. -- EXT_BG[2-3], EXT_DBG[2-3], and GBL can be left unconnected if they are multiplexed to the system bus functionality. For any other functionality, connect the signal lines based on the multiplexed functionality. -- BR must be pulled up. -- EXT_BR[2-3] must be pulled up if multiplexed to the system bus functionality. * If there is an external bus master (BCR[EBM] = 1): -- BR, BG, DBG, and TS must be pulled up. -- EXT_BR[2-3], EXT_BG[2-3], and EXT_DBG[2-3] must be pulled up if multiplexed to the system bus functionality. * In single-master mode, ABB and DBB can be selected as IRQ inputs and be connected to the non-active value. In other modes, they must be pulled up. Note: The MSC8122 does not support DLL-enabled mode. For the following two clock schemes, ensure that the DLL is disabled (that is, the DLLDIS bit in the Hard Reset Configuration Word is set). * If no system synchronization is required (for example, the design does not use SDRAM), you can use any of the available clock modes. * In the CLKIN synchronization mode, use the following connections: -- Connect the oscillator output through a buffer to CLKIN. -- Connect the CLKIN buffer output to the slave device (for example, SDRAM) making sure that the delay path between the clock buffer to the MSC8122 and the SDRAM is equal (that is, has a skew less than 100 ps). -- Valid clock modes in this scheme are: 0, 7, 15, 19, 21, 23, 28, 29, 30, and 31. MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 4-3 Design Considerations * In CLKOUT synchronization mode (for 1.2 V devices), CLKOUT is the main clock to SDRAM. Use the following connections: -- Connect the oscillator output through a buffer to CLKIN. -- Connect CLKOUT through a zero-delay buffer to the slave device (for example, SDRAM) using the following guidelines: * The maximum delay between the slave and CLKOUT must not exceed 0.7 ns. * The maximum load on CLKOUT must not exceed 10 pF. * Use a zero-delay buffer with a jitter less than 0.3 ns. -- All clock modes are valid in this clock scheme. Note: See the Clock chapter in the MSC8122 Reference Manual for details. * If the 60x-compatible system bus is not used and SIUMCR[PBSE] is set, PPBS can be disconnected. Otherwise, it should be pulled up. * The following signals: SWTE, DSISYNC, DSI64, MODCK[1-2], CNFGS, CHIPID[0-3], RSTCONF and BM[0-2] are used to configure the MSC8122 and are sampled on the deassertion of the PORESET signal. Therefore, they should be tied to GND or VDDH or through a pull-down or a pull-up resistor until the deassertion of the PORESET signal. * When they are used, INT_OUT (if SIUMCR[INTODC] is cleared), NMI_OUT, and IRQxx (if not full drive) signals must be pulled up. * When the Ethernet controller is enabled and the SMII mode is selected, GPIO10 and GPIO14 must not be connected externally to any signal line. Note: For details on configuration, see the MSC8122 User's Guide and MSC8122 Reference Manual. For additional information, refer to the MSC8122 Design Checklist (AN2787). 4.4 External SDRAM Selection The external bus speed implemented in a system determines the speed of the SDRAM used on that bus. However, because of differences in timing characteristics among various SDRAM manufacturers, you may have use a faster speed rated SDRAM to assure efficient data transfer across the bus. For example, for 166 MHz operation, you may have to use 183 or 200 MHz SDRAM. Always perform a detailed timing analysis using the MSC8122 bus timing values and the manufacturer specifications for the SDRAM to ensure correct operation within your system design. The output delay listed in SDRAM specifications is usually given for a load of 30 pF. Scale the number to your specific board load using the typical scaling number provided by the SDRAM manufacturer. MSC8122 Technical Data, Rev. 12 4-4 Freescale Semiconductor Thermal Considerations 4.5 Thermal Considerations An estimation of the chip-junction temperature, TJ, in C can be obtained from the following: TJ = TA + (R JA x PD) Equation 1 where TA = ambient temperature near the package ( C) RJA = junction-to-ambient thermal resistance ( C/W) PD = PINT + PI/O = power dissipation in the package (W) PINT = IDD x VDD = internal power dissipation (W) PI/O = power dissipated from device on output pins (W) The power dissipation values for the MSC8122 are listed in Table 2-3. The ambient temperature for the device is the air temperature in the immediate vicinity that would cool the device. The junction-to-ambient thermal resistances are JEDEC standard values that provide a quick and easy estimation of thermal performance. There are two values in common usage: the value determined on a single layer board and the value obtained on a board with two planes. The value that more closely approximates a specific application depends on the power dissipated by other components on the printed circuit board (PCB). The value obtained using a single layer board is appropriate for tightly packed PCB configurations. The value obtained using a board with internal planes is more appropriate for boards with low power dissipation (less than 0.02 W/cm2 with natural convection) and well separated components. Based on an estimation of junction temperature using this technique, determine whether a more detailed thermal analysis is required. Standard thermal management techniques can be used to maintain the device thermal junction temperature below its maximum. If TJ appears to be too high, either lower the ambient temperature or the power dissipation of the chip. You can verify the junction temperature by measuring the case temperature using a small diameter thermocouple (40 gauge is recommended) or an infrared temperature sensor on a spot on the device case that is painted black. The MSC8122 device case surface is too shiny (low emissivity) to yield an accurate infrared temperature measurement. Use the following equation to determine TJ: TJ = TT + ( JA x PD) Equation 2 where TT = thermocouple (or infrared) temperature on top of the package ( C) JA = thermal characterization parameter ( C/W) PD = power dissipation in the package (W) Note: See MSC8102, MSC8122, and MSC8126 Thermal Management Design Guidelines (AN2601/D). MSC8122 Technical Data, Rev. 12 Freescale Semiconductor 4-5 Ordering Information Consult a Freescale Semiconductor sales office or authorized distributor to determine product availability and place an order. Part MSC8122 Package Type Core Voltage Operating Temperature 1.1 V -40 to 105C Flip Chip Plastic Ball Grid Array (FC-PBGA) 1.2 V How to Reach Us: Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations not listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GMBH Technical Information Center Schatzbogen 7 81829 Munchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064, Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T. Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com MSC8122 Rev. 12 4/2006 Core Frequency (MHz) Order Number Lead-Free Lead-Bearing 300 MSC8122TVT4800V MSC8122TMP4800V 400 MSC8122TVT6400V MSC8122TMP6400V -40 to 105C 400 MSC8122TVT6400 MSC8122TMP6400 0 to 90C 500 MSC8122VT8000 MSC8122MP8000 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale, the Freescale logo, and CodeWarrior are trademarks of Freescale Semiconductor, Inc. StarCore is a licensed trademark of StarCore LLC. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2004, 2006.