Drawing No. JGB40-1497PRE P. 1/11 Specification of Piezoelectric Sounder PKMCS0909E4000-R1 Date 1. February 7, 2013 Scope This product specification is applied to the piezoelectric sounder used for sounder in alarm systems. Please contact us when using this product for any other applications than described in the above. 2. 2-1 Part Number :PKMCS0909E4000-R1 Murata Part Number : Customer's Part Number : Customer's Drawing Number 2-2 2-3 3. Maximum Rating Item Specification 3-1 Maximum Input Voltage 3-2 Operating Temperature Range -40 +85 -40 to +85C 3-3 Storage Temperature Range -40 +85 - 40 to +85C 12.5Vo-p /max Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE 4. P. 2/11 Electrical Characteristics Item 4-1 Sound Pressure Level Refer to next item for measuring method. 5. 5-1 Specification 65dB /min. Measuring Method S.P.L. Measuring Circuit 1.5Vo-p, 4kHz, Input Signal1.5Vo-p, 4kHz, Square wave 0.1m Piezoelectric Sounder Measuring equipment /Mic. /Pre Amp. / Audio Analyzer 5-2 Mic. Pre Amp. Audio Analyzer Type4191 (Bruel & kjaer) / or Equivalent Type2669 (Bruel & kjaer) / or Equivalent Type3560C (Bruel & kjaer) / or Equivalent Measuring Condition 0.1m+2536010R.H. +5+35,4585% After mounting products on PCB(0.1m), standard conditions for the measurement shall be +253C temperature and 6010%R.H. humidity. The measurement shall be performed at the temperature of +5 to +35C and the humidity of 45 to 85%R.H. unless otherwise the result is doubtful. Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE Physical Characteristics Item 6-1 Shock 6-2 Vibration Resistant 6-3 Bend Strength PCB Test Condition Specification 980m/s2 XYZ 3 3 Components shall be measured after being applied shock(980m/s2) for each three mutually perpendicular directions to each of 3 times by half sine wave. 1055Hz 1.5mm XYZ 3 2 Applying the vibration of amplitude 1.5mm and vibration frequency 10 to 55 Hz in each of 3 perpendicular directions for 2 hours. 115 1 After components soldered on PCB, the load shall be applied to the PCB as shown in below The measured value figure for 5 times (1 second per 1 time). shall meet Table 1. Pressing rod 20 10 load PCB R10 o5 Supporting rod 1.0 45 Sample under the test Off center 45 3 6. P. 3/11 / PCB thickness : 0.8mm / unit : mm Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE Soldering Heat Resistance (1) (1)Re-flow Soldering 2 1 Components shall be measured after applying twice of the re-flow soldering with following temperature profile and leaving in natural condition for 1 hour. Temperature (C) 6-4 P. 4/11 Peak (260C / max.) 260 230 Heating (230C) Pre-heating 100 (150-180C) Gradual Cooling 30 60 - 120 / sec. sec. min. (2) (2)Soldering with Iron 6-5 Solderability 1 The measured value shall meet Table 1. 40 120 sec. max. sec. min. +3505C3.00.51 Components shall be measured after soldered at +3505C for 3.00.5 seconds, and then being placed in natural condition for 1 hour. The soldering iron shall not touch the components while soldering. LF (Sn-3Ag-0.5Cu PCT+105C100%R.H. 4 5 90% +2455C30.5 The solder shall LF Solder (Sn-3Ag-0.5Cu After being kept in pressure cooker at +105C coat at least 90% temperature and 100%R.H. for 4 hours, of the surface of terminals of components shall be immersed in a terminal. soldering bath at temperature of +2455C for 30.5 seconds after being placed in a rosinmethanol for 5 seconds. Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE 7. P. 5/11 Environmental Characteristics Item Test Condition +852 240 4 Dry Heat Test Components shall be left in a chamber (Storage) (Temperature: +852C) for 240 hours, then measured after leaving in natural condition for 4 hours. 7-1 7-2 -402 240 4 Components shall be left in a chamber (Temperature: -402C) for 240 hours, then measured after leaving in natural condition for 4 hours. Cold Test (Storage) 7-3 +402 9095R.H. 240 4 Components shall be left in a chamber (90 to 1 95% R.H. at +402C) for 240 hours, then measured after leaving in natural condition for 4 The measured value shall meet Table 1. hours. Humidity 7-4 Specification -402 30 (+20) 15 +852 30 (+20) 15 1 5 4 Temperature Cycle After being placed in a chamber at -402C for 30 minutes, components shall be placed at room temperature (+20C). After 15 minutes at this temperature, components shall be placed in a chamber at +852C. After 30 minutes at this temperature, components shall be returned to room temperature (+20C) for 15 minutes. After 5 above cycles, components shall be measured after being placed in natural condition for 4 hours. 1 Table 1. Item Specification after test Sound Pressure Level 10dB Initial Value10dB Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE 8. P. 6/11 Dimensions Sound Emitting Hole 0.6 9.0 9.0 3.2 (1.5) (1.5) (0.3) 1.9max. 0 0 Open Hole (2.0) Recommendable Land Pattern 3.4 (1.5) 10.0 7.4 1.0 () (Note) 4 1 The location of sound Emitting hole is not specified. : Vender's Code : EIAJ Monthly : mm in mm Tol. : 0.2 0.2 * Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE 9. P. 7/11 Taping Method 9-1 () The carrier tape shall be wound clockwise. The feeding holes shall be to the right side as the tape is pulled toward the user. 9-2 1 2,000 A reel shall contain 2,000pcs of components. 9-3 1 The minimum packaging unit shall be a reel. And each reel shall have a label which shows part number, quantity and outgoing inspection number. Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE P. 8/11 1.50 +0.1 -0.0 9.50.1 M 0 0 M 0 0 M 0 0 M 0 0 9.50.1 2.00.1 Direction of Feed 12.00.1 0.30.1 16.00.3 4.00.1 1.750.1 Dimensions of Plastic Tape 7.50.1 1 Figure 1. 2.40.2 Cover Film 10 in mm 0.10.7N The cover Film peel strength force 0.1 to 0.7N 300mm/ The cover Film peel speed 300mm/min. 2 Figure 2. Dimensions of Plastic Reel (330) (80) Trailer 160200 2.00.5 Components Cover Film 240280 Empty 400560 Leader 17.41.0 22.5max. 13.00.5 :mm in mm Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE 10 ! P. 9/11 Cautions 10-1 Limitation of Applications () Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property . Aircraft equipment Aerospace equipment Undersea equipment Power plant control equipment Medical equipment Transportation equipment(vehicles, trains, ships, etc.) Traffic signal equipment Disaster prevention / crime prevention equipment Data-processing equipment Applications of similar complexity and /or with reliability requirements to the applications listed In the above. 10-2 Fail-safe Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. 11 Cautions for Use 11-1 The component may be damaged if mechanical stress over this specification is applied. 11-2 Please pay attention to protect operating circuit from surge voltage provided by something of force such as falling, shock and temperature changing. 11-3 Please pay attention never to be applied DC voltage to component. There is possibility that silver migration will occur. Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE P. 10/11 11-4 ICICIC12k The resistor should be used as shown in Fig. A. A suitable resistance value should be chosen, preferably 1k to 2k. Instead of this measure, a diode may also be applied as shown in Fig. B. IC IC Fig.B Fig.A 11-5 Washing of the component is not acceptable, because it is not sealed. 11-6 High pressure air should not be blown on the component directly at short range by air gun or equivalent. 11-7 Please do not adsorb the sound emitting hole when the component is mounted. 12 Notice on Product Storage 12-1 -10+401585% Please store the products in room where the temperature / humidity is stable. And avoid such places where there are large temperature changes. Please store the products under the following conditions : Temperature : -10 to +40 (degree C) Humidity : 15 to 85% R.H. 12-2 66 6 Expire date (Shelf life) of the products is 6 months after delivery under the conditions of a sealed and an unopened package. Please use the products within 6 months after delivery. If you store the products for a long time (more than 6months), use carefully because the products may be degraded in the solder-ability and/or rusty. Please confirm solder-ability and characteristics for the products regularly. 12-3 Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality, and/or be degraded in the solder-ability due to the storage in a chemical atmosphere. 12-4 Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. Murata Manufacturing Co.,Ltd. Drawing No. JGB40-1497PRE P. 11/11 12-5 Please do not store the products in the places such as : in a damp heated place, in a place where direct sunlight comes in, in place applying vibrations. 12-6 Please use the products immediately after the package is opened, because the characteristics may be reduced in quality, and/or be degraded in the solder-ability due to storage under the poor condition. 12-7 Please do not drop the products to avoid cracking of ceramic element. 13 ! Note 13-1 Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 13-2 You are requested not to use our product deviating from this product specification. 13-3 1 Please return one duplicate of this product specification to us with your signature to acknowledge your receipt . In case of no return within three months from submission date, or if we receive order before the duplicate is returned, this product specification will be deemed to have been received by you. 13-4 We consider it not appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents. Therefore, if your technical documents as above include such terms and conditions such as warranty clause, product liability clause, or intellectual property infringement liability clause, they will be deemed to be invalid. Murata Manufacturing Co.,Ltd. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Murata: PKMCS0909E4000-R1