Philips Semiconductors Prod uct specification Low power quad op amps LM124/224/324/324A/ SA534/LM2902 DESCRIPTION The LM124/SA534/LM2902 series consists of four independent, high-gain, internally frequency-compensated operational amplifiers designed specifically to operate from a single power supply over a wide range of voltages. UNIQUE FEATURES In the linear mode, the input common-mode voitage range includes ground and the output voltage can also swing to ground, even though operated from only a single power supply voltage. The unity gain crossover frequency and the input bias current are temperature-compensated. PIN CONFIGURATION D, F, N Packages NS 14] ouTPUT 4 A 13 | ANPUT 4 11] GND 12 | +INPUT 4 10 | 4INPUT 3 +INPUT 2 | 5 -INPUT 2 | 6 iy vj 9 | -INPUT 3 OUTPUT 2 | 7 8 | OUTPUT 3 FEATURES Internally frequency-compensated for unity gain rope SLOO06S Large DC voltage gain: 100dB Figure 1. Pin Configuration Wide bandwidth (unity gain): 1MHz (temperature-compensated) Wide power supply range Single supply: 3Vpc to 30Vpc or dual supplies: +1.5Vpc to+15Vpc Very low supply current drain: essentially independent of supply voltage (1mW/op amp at +5Vpc) Low input biasing current: 45nApc (temperature-compensated) Low input offset voltage: 2MVpc and offset current: 5nApo Differential input voltage range equal to the power supply voltage Large output voltage: OVpc to Voc-1.5Vpc swing ORDERING INFORMATION DESCRIPTION TEMPERATURE RANGE ORDER CODE DWG # 14-Pin Plastic Dual In-Line Package (DIP) -55C to +125C LM124N SOT27-1 14-Pin Ceramic Dual In-Line Package (CERDIP) -55C to +126C LM124F 0581B 14-Pin Plastic Dual In-Line Package (DIP) -25C to +85C LM224N SOT27-1 14-Pin Ceramic Dual In-Line Package (CERDIP) -25C to +85C LM224F 0581B 14-Pin Plastic Small Outline (GO) Package -25C to +85C LM224D SOT108-1 14-Pin Plastic Dual In-Line Package (DIP) 0C to +70C LM324N SOT27-1 14-Pin Ceramic Dual In-Line Package (CERDIP) OC to +70C LM324F 0581B 14-Pin Plastic Small Outline (SO) Package 0C to +70C LM324D SOT108-1 14-Pin Plastic Dual In-Line Package (DIP) 0C to +70C LM324AN SOT27-1 14-Pin Plastic Small Outline (SO) Package 0C to +70C LM324AD SOT108-1 14-Pin Plastic Dual In-Line Package (DIP) -40C to +85C SA534N SOT27-1 14-Pin Ceramic Dual In-Line Package (CERDIP) -40C to +85C SAS534F 0581B 14-Pin Plastic Small Outline (SO) Package -40C to +85C SA534D SOT108-1 14-Pin Plastic Small Outline (SO) Package -40C to +125C LM2902D SOT108-1 14-Pin Plastic Dual In-Line Package (DIP) -40C to +125C LM2902N SOT27-1 4995Nov27 (<M 7110826 0098209 230 mm 2 853-0929 16050Philips Semiconductors Product specification LM124/224/324/324A/ Low power quad op amps SA534/LM2902 ABSOLUTE MAXIMUM RATINGS SYMBOL PARAMETER RATING UNIT Veco Supply voltage 32 or +16 Voc VIN Differential input voltage 32 Voc Vin Input voltage -0.3 to +32 Voc p Maximum power dissipation, D Ta=25C (still-air)! N package 1420 mW F package 1190 mw D package 1040 mW Output short-circuit to GND one amplifier? j Voc<15Vpc and Ta=25C Continuous lin Input current (Vixy<-0.3V)9 50 mA Ta Operating ambient temperature range LM324/A 0 to +70 C LM224 -25 to +85 C SA534 -40 to +85 C LM2902 -40 to +125 C LM124 -55 to +125 G Tsta Storage temperature range -65 to +150 C TsoLp Lead soldering temperature (10sec max) 300 C NOTES: 1. Derate above 25C at the following rates: F package at 9.5mW/C N package at 11.4mW/C D package at 8.3mW/C 2. Short-circuits from the output to Voc + can cause excessive heating and eventual destruction. The maximum output current is approximately 40mA, independent of the magnitude of Vcc. At values of supply voltage in excess of +15Vp continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. 3. This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistors becoming forward biased and thereby acting as input bias clamps. In addition, there is also fateral! NPN parasitic transistor action on the IC chip. This action can cause the output voltages of the op amps to go to the V+ rail (or to ground for a large overdrive) during the time that the input is driven negative. 1995 Nov 27 Me 7110826 0098210 TS2Philips Semiconductors Product specification Low power quad op amps SA534/LM2902 DC ELECTRICAL CHARACTERISTICS Voc=5V, Ta=25C unless otherwise specified. LM124/LM224 LM324/SA534/LM2902 SYMBOL PARAMETER TEST CONDITIONS - = UNIT Min Typ Max Min Typ Max V Offset voltage Rg=02 +2 +5 +2 +7 V os Set womage Rg=02, over temp. +7 +9 m AVos/AT Temperature drift Rg=0Q, over temp. 7 7 pV/PC input g lin(+) oF bin) 45 150 45 250 A BIAS npur caren lin(+) oF lin(-), over temp. 40 300 40 500 " Algias/AT | Temperature drift Over temp. 50 50 parc lin(+)-lin(-) +3 +30 +5 +50 A los Offset current lin(+)-liy(-), over temp. +100 +150 n Alos/AT Temperature drift Over temp. 10 10 pArc Common-mode voltage Voecs30V Voo-1.5 0 Voc-i.5 V V cM range? Voc<30V, over temp. Vec-2 Vec-2 cmAR | Common-mode rejection Veo=30V 70 | 85 65 | 70 dB . Ri =2kQ, Vec=30V, Vout Output voltage swing U over tomp 26 26 Vv < = Vou Output voltage high PS ce 30V, a7 | 28 27 | 28 V < VoL Output voltage low ar temn 5 20 5 20 mv Fi=e, Veo=30V, 1.5 3 1.5 3 over temp. lec Supply current Ae mA ve 0.7 1.2 0.7 1.2 over temp. Voc=15V (for large Vo swing), R.22k 50 100 25 100 AVoL Large-signal voltage gain Voec=15V (for large Vo Vim swing), RL22kQ, 25 15 over temp. Amplifier-to-amplifier f=1 kHz to 20kKHz, -120 -120 dB coupling input referred PSRR Power supply rejection ratio Rgs0Q 65 100 65 100 dB Output current Vint=+1V, Vin-=0V, 20 40 20 40 source Voc=15V Vint=+1V, Vin=0V, 10 | 20 10 | 20 Voc=15V, over temp. A m lout Output current MI 10 | 20 10 | 20 . Vin-=+1V, Vint=OV, sink Vec=15V, over temp. 8 S 8 Vin-=+1 Vv, Vint=0V, Vo=200mV 12 50 12 50 pA Isc Short-circuit current4 10 40 60 10 40 60 mA GBW Unity gain bandwidth 1 1 MHz SR Slew rate 0.3 0.3 V/us VNOISE Input noise voltage f=1kHz 40 40 nV/AHz VoirF Differential input voltage? Voc Voc V 1995 Nov 27 MH 7110826 00548211 999 omPhilips Semiconductors Product specification LM124/224/324/324A/ Low power quad op amps SA534/LM2902 DC ELECTRICAL CHARACTERISTICS (Continued) Voc=5V, Ta=25C unless otherwise specified. LM324A SYMBOL PARAMETER TEST CONDITIONS - UNIT Min Typ Max Rg=02 +2 43 Vos Offset voltage! RocdO, over temp. = mV AVgs/AT Temperature drift Rg=0Q, over temp. 7 30 pvc . linG) or lin) 45 100 lBias Input current? lin(+) OF lyy(-), over temp. 40 200 na Algias/AT Temperature drift Over temp. 50 pA?c fin(+)-lin(-) +5 +30 los Offset current T)liw(-), over temp. +75 nA Alos/AT Temperature drift Over temp. 10 300 pAc Vom Common-mode voltage range? Voecs30V 0 Voo-1.5 Vv Vocss0V, over temp. 0 Voc-2 Vv CMRR Common-mode rejection ratio Voec=30V 65 85 dB : RL=2kQ, Voc=30V, Vout Output voltage swing over temp. 26 Vv Vou Output voltage high Ris10kQ, Voc=30V, over temp. 27 28 Vv VoL Output voltage low aor toma, 5 20 mV lec Supply current R=, Vec=30V, over temp. 1.5 3 mA Ri =e, over temp. 0.7 1.2 mA AVOL Large-signal voltage gain Vec=15V (for large Vo swing), Rp2=2kQ 25 100 VimvV Voc=15V (for large Vo swing), RL22kQ, 45 VimV over temp. Amplifier-to-amplifier couplingS ppult rae -120 dB PSRR Power supply rejection ratio Rgs0Q 65 100 dB Output current Vint=+1V, Vin-=0V, Vec=15V 20 40 mA Vint=+1V, Vin-=0V, Vec=15V, over temp. 10 20 mA lout Output current Vinc=+1V, Vint=OV, Voc=15V 10 20 mA sink Vin-=+1V, Vint=0V, Vec=15V, over temp. 5 8 mA Vin-=t41V, Vint=0V, Vo=200mV 12 50 HA Isc Short-circuit current* 10 40 60 mA VolFF Differential input voltage? Voc V GBW Unity gain bandwidth 1 MHz SR Slew rate 0.3 Vis VNOISE Input noise voltage f=1kHz 40 nVAVHz NOTES: 1. Vo* 1.4Vpc, Rg=02 with Voc from SV to 30V and over full input common-mode range (OVpc+ to Ver -1.5V). 2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. 3. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is Vc -1.5, but either or both inputs can go to +32V without damage. 4. Short-circuits from the output to Vec can cause excessive heating and eventual destruction. The maximum output current is approximately 40mA independent of the magnitude of Vcc. At values of supply voltage in excess of +15Vpc, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. 5. Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of coupling increases at higher frequencies. 1995 Nov 27 mm 71108 a, oodaele 25 MM,Product specification LM124/224/324/324A/ Low power quad op amps SA534/LM2902 Philips Semiconductors EQUIVALENT CIRCUIT v, 0 + 6 6HA 10014! 9 BHA J as Q7 Rec mM at OUTPUT INPUTS = Qu {ars +o Qi2 50uA Q8 SLOO06E Figure 2. Equivalent Circuit 1995Nov27 MH 71120826 0098213 7b] mm &Philips Semiconductors Product specification Low power quad op amps LM124/224/324/324A/ SA534/LM2902 TYPICAL PERFORMANCE CHARACTERISTICS SUPPLY CURRENT DRAIN (mAdc) AOL VOLTAGE GAIN (dB) 160 ary x] So a o Ps So Supply Current Ta = 0C to *125C TA = -55C 10 20 30 40 SUPPLY VOLTAGE (Vpc) OP0S450S Voltage Gain RL +20 Ka RL +2KQ 10 20 30 40 SUPPLY VOLTAGE (Vpc) OP0s480S V, - OUTPUT VOLTAGE REFERENCE TO V+ (Vpc) 2 1 0.001 0.01 Ig* - OUTPUT SOURCE CURRENT (mApc) 10 01 Vo~ OUTPUT VOLTAGE (Vpc) 0.01 Output Characteristics Current Sourcing T t D V+ + +V" /2 V2 lo | INDEPENDENT OF V+ Ta = 425C / Ht 0.1 1 10 Output Characteristics Current Sinking 100 OPpos460S T T vt=45Vpc Vt 2415 Vpe i] vt=+30Vpc 77 LZ Ta = +25C 0.001 0.01 0.1 1 10 100 ig ~ OUTPUT SINK CURRENT (mApc) OP0S480S OUTPUT CURRENT (mAdc) VOLTAGE GAIN (dB) Current Limiting 90 80 70 60 50 40 30 20 10 0 55 35 -15 5 25 45 65 85 105 125 TEMPERATURE (C) OP05470S Open-Loop Frequency Response 0.1pf \ " 80 = = vt = 30 Voc AND 60 \ XI < TA < +1259 40 120 100 Vt =10 to 15 Voc AND 20] -55C < TA < +125C N 1 10 100 1K 10K 100K 1M 10M FREQUENCY (Hz) OPos500S $L00067 Figure 3. Typical Performance Characteristics 1995Nov27 MH 7110826 OOF6214 bTs moPhilips Semiconductors Product specification LM124/224/324/324A/ Low power quad op amps SA534/L M2902 TYPICAL PERFORMANCE CHARACTERISTICS (Continued) Large-Scale Voltage-Follower Frequency Response > Pulse Response Input Voltage Range wo te 15 Vpc 9 <2K V7" 15Vpc ~ 5 Qo ao = o > g S zi J/| 5 ~ S a 10 = 3 < NEGATIVE V4 wd 8 5 = E POSITIVE = > a w a 5 3 Z5 | 3 F 2 > 3 oY 5 & 1K 10K 100K 1M Zz 0 10 20 30 40 0 5 10 15 FREQUENCY (Hz) TIME (1S) POWER SUPPLY VOLTAGE (+ Vpc) vt OR V- ~ Voltage-Follower Pulse Input Current 3 Common-Mode Rejection Ratio Response (Small-Signal) 500 90 2 120 TTT 80 Vom = Voc = ~ z ~ 8 70 + | | ze mn a % 450 Eo < vt =430Vp 8 we Tr 50pF = 60 3 80 g vy _. f\ a 5 400 ~ _ iad 50 w oO = Vv x Vt =+15 Voc Q 60 > | 3% 5 = 350 weer 5 30 5 40 5 z 9 OUTPUT z = $ 1 20 Vt =45 Voc So on p 300 iN. * 10 J Ta = +25C Po vt = 430 Vpc 0 i 250 -55 35-15 5 25 45 65 85 105 125 = 100 ik 10k 100k 1M o 1 2 3 4 5 6 7 8 Ta TEMPERATURE (C) f FREQUENCY (Hz) L TIME (8) SL00068 Figure 4. Typical Performance Characteristics (cont.) TYPICAL APPLICATIONS RF -vWA Ve RIN 8 vinOWw 4 pO V = 9 VIN >_o Vo Ve 2 Single Supply Inverting Amplifier Non-Inverting Amplifier Input Biasing VoltageFollower SLOO069 Figure 5. Typical Applications 1995Nov27 mm 7410826 0098215 534 mm 8Product specification LM124/224/324/324A/ Philips Semiconductors Low power quad op amps SA534/LM2902 14-PIN (300 mils wide) CERAMIC DUAL IN-LINE (F) PACKAGE 0581B (S20) O10'0 (29"2) 00"9 (ge'0) S100 (0'01) s6e'0 ( 3LON) (292} 006'0 o f osa I {4s0) oz0'0 | (eh) SPOO @ 1 | | Yao 3 Srl'O (Srv) S210 (vy S3LON) (2Z) 062'0 (era) ozo *do} Su} Woy POMBIA USUM F1# Ul 0} ASIMYDO}OI9}UNDD enuljuod pue }# Uld YUM YR}S SIBqUUNU Ul SG | eueld oO} JejnoIpUuedied 6q oO} pauleSUOS Sped| OU) UM Peunsesw SUdISUBLUID eSeUL P "yoewWSsiwW ese 0} pl} pue aul| ees ay] UO SNdsIUeWW PUB UNJEA ssejb 10} BOUMO||e Bpnjou! pue Apoq eu} uo suunyep eoueieje/ ee 4, pue Ld, 1, e Z8G6L-WNGS PLA ISN Jed Buloueseso] pue uolsuawig Zz saselquesed ul UMOUs Qe SISJOWUIIIIW SeYou| :uoIsUaLUIP Bul]}ONjU0T) 1 "SALON fenenace|S als [1 [S| (80) SLO'O (830) 20'0 7 r - (8L') S20 (61'r) Sot0 ANV1d NILYSS (61) Sato (80's) 0020 (22'1) 0s00 (g2'1) 0200 (1 61) esz'0 ~a (661) S820 os (ps2) 0010 -+| (229) Srz0 C _3_ (9224) 98z0 [-3-] (22' 1) oso'o _. (2% 1) oSo'o _ (62'2) O10 (622) O10 853-0581B 06688 me 7110826 005821b 470 1995 Nov 27Philips Semiconductors Product specification Low power quad op amps SA534/L M2902 DIP14: plastic dual in-line package; 14 ieads (300 mil) SOT27-1 + D o> ME o 5 a a : 1 P| f , AL 4 it | | | ! | i (84) b 14 & My med : + ---_----}4 cE 7 0 5 10 mm ps AS a a a | scale OIMENSIONS (inch dimensions are derived from the original mm dimensions) A A A 1 1 z UNIT | max | omnis. | mex. b b, po | &f e e; L ME My w max, 1.73 0.53 0.36 19.50 6.48 3.60 8.25 10.0 mm 42 ] 051 | 32 1 443 | 038 | 023 | 1855 | 620 | 254 | 762 | 305 | 780 | a3 | 2254) 22 . 0.068 | 0.021 0.014 0.77 0.26 0.14 0.32 0.39 inches | 0.17 | 0.020 | 0.13 | Qo44 0015 | 0009 | 073 024 0.10 030 | g40 031 033 0.01 | 0,087 Note 1. Plastic or meta! protrusions of 0.25 mm maximum per side are not included. OUTLINE REFERENCES EUROPEAN ISSUE DATE VERSION IEC JEDEC EIAJ PROJECTION B24 SOT27-1 050G04 MO-001AA f&} 95-03-11 1995Nov27 mg 71410826 0098217 307 a 10Philips Semiconductors Product specification LM124/224/324/324A/ Low power quad op amps SA534/LM2902 $014: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1 Oly a ooaooe : PCN 2 t pines ye? , | 7 _ as iH ug H oo aie ; p 0 2.5 5mm Daa es} scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT | max, | At | Az | As bp c pM | eM | e He L Lp Q v w y | zM] 6 0.25 | 1.45 0.49 | 025 | 3.75 | 4.0 62 10 | 07 07 mm 1175) o10 | 1.25 | 75 | ose] o19| ass} 3a | 127] sa 1 1] o4 | o6 | 97] O79 | OT] os | Co " 0.0098] 0.057 0.019 [0.0098] 0.35 | 0.16 0.24 0.039 | 0.028 0.028} 9 inches | 0.069 4 o939] 0.049 | 9-97 | 0.014 [0.0075] 0.34 | 0.15 | 99} 9.23 | 9-941 | 016 | 0.024 | 9-04 | 9.01 | 0.004) Qo, Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE REFERENCES EUROPEAN ISSUE DATE VERSION IEC JEDEC EIAJ PROJECTION 94-08-43- SOT108-1 076E06S MS-012AB --} 95.01.23 1995Nov27 MM 7110826 00982146 243 mm 1