LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 LM101AJAN Operational Amplifiers Check for Samples: LM101AJAN FEATURES DESCRIPTION * The LM101A is a general purpose operational amplifier which features improved performance over industry standards such as the LM709. Advanced processing techniques make possible an order of magnitude reduction in input currents, and a redesign of the biasing circuitry reduces the temperature drift of input current. Improved specifications include: * Offset voltage 3 mV maximum over temperature * Input current 100 nA maximum over temperature * Offset current 20 nA maximum over temperature * Ensured drift characteristics * Offsets ensured over entire common mode and supply voltage ranges * Slew rate of 10V/s as a summing amplifier 1 2 * * * * * Offset Voltage 3 mV Maximum Over Temperature Input Current 100 nA Maximum Over Temperature Offset Current 20 nA Maximum Over Temperature Ensured Drift Characteristics Offsets Ensured Over Entire Common Mode and Supply Voltage Ranges Slew Rate of 10 V/S as a Summing Amplifier 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2006-2013, Texas Instruments Incorporated LM101AJAN SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 www.ti.com This amplifier offers many features which make its application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, and freedom from oscillations and compensation with a single 30 pF capacitor. It has advantages over internally compensated amplifiers in that the frequency compensation can be tailored to the particular application. For example, in low frequency circuits it can be overcompensated for increased stability margin. Or the compensation can be optimized to give more than a factor of ten improvement in high frequency performance for most applications. In addition, the device provides better accuracy and lower noise in high impedance circuitry. The low input currents also make it particularly well suited for long interval integrators or timers, sample and hold circuits and low frequency waveform generators. Further, replacing circuits where matched transistor pairs buffer the inputs of conventional IC op amps, it can give lower offset voltage and a drift at a lower cost. Schematic Pin connections shown are for 8-pin packages Connection Diagrams 2 Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 Pin 4 connected to case. Figure 1. (Top View) TO-99 Package See Package Number LMC Figure 2. (Top View) CDIP Package See Package Number NAB0008A Figure 3. (Top View) CDIP Package See NS Package Number J Figure 4. (Top View) CLGA Package See NS Package Number NAD0010A Fast AC/DC Converter Feedforward compensation can be used to make a fast full wave rectifier without a filter. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN 3 LM101AJAN SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 www.ti.com Absolute Maximum Ratings (1) Supply Voltage 22V Differential Input Voltage 30V Input Voltage (2) 15V Output Short Circuit Duration Continuous -55C TA +125C Operating Ambient Temp. Range TJ Max 150C Power Dissipation at TA = 25C (3) LMC-Package Still Air) NAB0008A-Package J-Package NAD0010A-Package LMC-Package NAB0008A-Package JA J-Package Thermal Resistance NAD0010A-Package JC (Typical) 750 mW (500 LF / Min Air Flow) 1,200 mW (Still Air) 1,000 mW (500 LF / Min Air Flow) 1,500 mW (Still Air) 1,200mW (500 LF / Min Air Flow) 2,000mW (Still Air) 500mW (500 LF / Min Air Flow) 800mW (Still Air) 165C/W (500 LF / Min Air Flow) 89C/W (Still Air) 128C/W (500 LF / Min Air Flow) 75C/W (Still Air) 98C/W (500 LF / Min Air Flow) 59C/W (Still Air) 233C/W (500 LF / Min Air Flow) 155C/W LMC-Package 39C/W NAB0008A-Package 26C/W J-Package 24C/W NAD0010A-Package 26C/W -65C TA +150C Storage Temperature Range Lead Temperature (Soldering, 10 sec.) 300C ESD Tolerance (4) 3000V (1) (2) (3) (4) 4 Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is intended to be functional, but do no ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. For supply voltages less than 15V, the absolute maximum input voltage is equal to the supply voltage. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), JA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA) / JA or the number given in the Absolute Maximum Ratings, whichever is lower. Human body model, 100 pF discharged through 1.5 k. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 Quality Conformance Inspection Mil-Std-883, Method 5005 - Group A Subgroup Description Temp (C) 1 Static tests at 25 2 Static tests at 125 3 Static tests at -55 4 Dynamic tests at 25 5 Dynamic tests at 125 6 Dynamic tests at -55 7 Functional tests at 25 8A Functional tests at 125 8B Functional tests at -55 9 Switching tests at 25 10 Switching tests at 125 11 Switching tests at -55 LM101JAN Electrical Characteristics DC Parameters The following conditions apply to all parameters, unless otherwise specified VCC = 20V, VCM = 0V, RS = 50 Symbol Parameters Conditions VIO Input Offset Voltage IIO IIB Input Offset Current Input Bias Current Min Max Unit Subgroups +VCC = 35V, -VCC = -5V, VCM = -15V -2.0 +2.0 mV 1 -3.0 +3.0 mV 2, 3 +VCC = 5V, -VCC = -35V, VCM = +15V -2.0 +2.0 mV 1 -3.0 +3.0 mV 2, 3 VCM = 0V -2.0 +2.0 mV 1 -3.0 +3.0 mV 2, 3 +VCC = 5V, -VCC = -5V, VCM = 0V -2.0 +2.0 mV 1 -3.0 +3.0 mV 2, 3 +VCC = 35V, -VCC = -5V, VCM = -15V, RS = 100K -10 +10 nA 1, 2 -20 +20 nA 3 +VCC = 5V, -VCC = -35V, VCM = +15V, RS = 100K -10 +10 nA 1, 2 -20 +20 nA 3 VCM = 0V, RS = 100K -10 +10 nA 1, 2 -20 +20 nA 3 +VCC = 5V, -VCC = -5V, VCM = 0V, RS = 100K -10 +10 nA 1, 2 -20 +20 nA 3 +VCC = 35V, -VCC = -5V, VCM = -15V, RS = 100K -0.1 75 nA 1, 2 -0.1 100 nA 3 +VCC = 5V, -VCC = -35V, VCM = +15V, RS = 100K -0.1 75 nA 1, 2 -0.1 100 nA 3 VCM = 0V, RS = 100K -0.1 75 nA 1, 2 -0.1 100 nA 3 -0.1 75 nA 1, 2 -0.1 100 nA 3 +VCC = 5V, -VCC = -5V, VCM = 0V, RS = 100K +PSRR -PSRR Power Supply Rejection Ratio Power Supply Rejection Ratio +VCC = 10V, -VCC = -20V +VCC = 20V, -VCC = -10V Notes -50 +50 V/V 1 -100 +100 V/V 2, 3 -50 +50 V/V 1 -100 +100 V/V 2, 3 Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN 5 LM101AJAN SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 www.ti.com LM101JAN Electrical Characteristics DC Parameters (continued) The following conditions apply to all parameters, unless otherwise specified VCC = 20V, VCM = 0V, RS = 50 Symbol Parameters Conditions CMRR Common Mode Rejection Ratio VCC = 35V to 5V, VCM = 15V +VIO Adj Adjustment for Input Offset Voltage -VIO Adj Adjustment for Input Offset Voltage +IOS Output Short Circuit Current +VCC = 15V, -VCC = -15V, t 25mS, VCM = -15V -IOS Output Short Circuit Current +VCC = 15V, -VCC = -15V, t 25mS, VCM = +15V ICC Power Supply Current +VCC = 15V, -VCC = -15V VIO / T IIO / T -AVS (1) (2) (3) 6 dB 1, 2, 3 4.0 mV 1, 2, 3 mV 1, 2, 3 mA 1, 2, 3 +60 mA 1, 2, 3 3.0 mA 1 2.32 mA 2 3.5 mA 3 -60 -18 +18 V/C 2 +25C TA +125C See (1) -15 +15 V/C 3 -55C TA +25C See (2) -200 +200 pA/C 2 +25C TA +125C See (2) -100 +100 pA/C 3 Large Signal (Open Loop) Voltage RL = 2K, VO = -15V Gain See (3) 50 V/mV 4 (3) 25 V/mV 5, 6 See (3) 50 V/mV 4 See (3) 25 V/mV 5, 6 See (3) 50 V/mV 4 See (3) 25 V/mV 5, 6 See (3) 50 V/mV 4 See (3) 25 V/mV 5, 6 See (3) 10 V/mV 4, 5, 6 See (3) 10 V/mV 4, 5, 6 RL = 10K, VCM = -20V +16 V 4, 5, 6 RL = 2K, VCM = -20V +15 V 4, 5, 6 Temperature Coefficient of Input Offset Current Large Signal (Open Loop) Voltage RL = 2K, VO = +15V Gain VCC = 5V, RL = 10K, VO = 2V -VOP 80 See (1) Large Signal (Open Loop) Voltage VCC = 5V, RL = 2K, Gain VO = 2V +VOP Subgroups Max -55C TA +25C Temperature Coefficient of Input Offset Voltage RL = 10K, VO = +15V AVS Unit Min -4.0 RL = 10K, VO = -15V +AVS Notes Output Voltage Swing Output Voltage Swing See RL = 10K, VCM = 20V -16 V 4, 5, 6 RL = 2K, VCM = 20V -15 V 4, 5, 6 Calculated parameter Calculated parameter Datalog reading of K = V/mV. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 LM101AJAN Electrical Characteristics AC Parameters The following conditions apply to all parameters, unless otherwise specified VCC = 20V, VCM = 0V, RS = 50 Symbol Parameter Conditions Units Subgroups +SR Slew Rate AV = 1, VI = -5V to +5V -SR Slew Rate AV = 1, VI = +5V to -5V 0.3 V/S 7 0.3 V/S TRTR Rise Time AV = 1, VI = 50mV 7 800 nS TROS Overshoot 7 AV = 1, VI = 50mV 25 % 7 NIBB NIPC Noise Broadband BW = 10Hz to 5KHz, RS = 0 15 VRMS 7 Noise Popcorn BW = 10Hz to 5KHz, RS = 100K 80 VPK 7 Min Max Units Subgroups Notes Min Max LM101AJAN Electrical Characteristics DC Parameters: Drift Values The following conditions apply to all parameters, unless otherwise specified VCC = 20V, VCM = 0V, RS = 50 Delta calculations performed on JAN S devices at group B, Subgroup 5 only. Symbol Parameter Conditions VIO Input Offset Voltage VCM = 0V -0.5 0.5 mV 1 IIB Input Bias Current VCM = 0V, RS = 100K -7.5 7.5 nA 1 Notes Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN 7 LM101AJAN SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics LM101A 8 Input Voltage Range Output Swing Figure 5. Figure 6. Voltage Gain Supply Current Figure 7. Figure 8. Voltage Gain Maximum Power Dissipation Figure 9. Figure 10. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 Typical Performance Characteristics LM101A (continued) Input Current, LM101A Input Noise Voltage Figure 11. Figure 12. Input Noise Current Common Mode Rejection Figure 13. Figure 14. Power Supply Rejection Closed Loop Output Impedance Figure 15. Figure 16. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN 9 LM101AJAN SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics for Various Compensation Circuits (1) Single Pole Compensation Two Pole Compensation CS= 30 pF CS= 30 pF C2 = 10 C1 fo= 3 MHz (1) 10 Figure 17. Figure 18. Feedforward Compensation Open Loop Frequency Response Figure 19. Figure 20. Pin connections shown are for 8-pin packages. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 Typical Performance Characteristics for Various Compensation Circuits(1) (continued) Open Loop Frequency Response Open Loop Frequency Response Figure 21. Figure 22. Large Signal Frequency Response Large Signal Frequency Response Figure 23. Figure 24. Large Signal Frequency Response Voltage Follower Pulse Response Figure 25. Figure 26. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN 11 LM101AJAN SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics for Various Compensation Circuits(1) (continued) 12 Voltage Follower Pulse Response Inverter Pulse Response Figure 27. Figure 28. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 TYPICAL APPLICATIONS (2) Inverting Amplifier with Balancing Circuit Variable Capacitance Multiplier May be zero or equal to parallel combination of R1 and R2 for minimum offset. Simulated Inductor Sine Wave Oscillator L R1 R2 C1 RS = R2 RP = R1 fo = 10 kHz Fast Inverting Amplifier with High Input Impedance Integrator with Bias Current Compensation *Adjust for zero integrator drift. Current drift typically 0.1 nA/C over -55C to +125C temperature range. (2) Pin connections shown are for 8-pin packages. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN 13 LM101AJAN SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 www.ti.com Application Hints (2) Protecting Against Gross Fault Conditions *Protects input Protects output Protects output--not needed when R4 is used. Compensating for Stray Input Capacitances or Large Feedback Resistor Isolating Large Capacitive Loads Although the LM101A is designed for trouble free operation, experience has indicated that it is wise to observe certain precautions given below to protect the devices from abnormal operating conditions. It might be pointed out that the advice given here is applicable to practically any IC op amp, although the exact reason why may differ with different devices. 14 Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 When driving either input from a low-impedance source, a limiting resistor should be placed in series with the input lead to limit the peak instantaneous output current of the source to something less than 100 mA. This is especially important when the inputs go outside a piece of equipment where they could accidentally be connected to high voltage sources. Large capacitors on the input (greater than 0.1 F) should be treated as a low source impedance and isolated with a resistor. Low impedance sources do not cause a problem unless their output voltage exceeds the supply voltage. However, the supplies go to zero when they are turned off, so the isolation is usually needed. The output circuitry is protected against damage from shorts to ground. However, when the amplifier output is connected to a test point, it should be isolated by a limiting resistor, as test points frequently get shorted to bad places. Further, when the amplifier drives a load external to the equipment, it is also advisable to use some sort of limiting resistance to preclude mishaps. Precautions should be taken to insure that the power supplies for the integrated circuit never become reversed--even under transient conditions. With reverse voltages greater than 1V, the IC will conduct excessive current, fusing internal aluminum interconnects. If there is a possibility of this happening, clamp diodes with a high peak current rating should be installed on the supply lines. Reversal of the voltage between V+ and V- will always cause a problem, although reversals with respect to ground may also give difficulties in many circuits. The minimum values given for the frequency compensation capacitor are stable only for source resistances less than 10 k, stray capacitances on the summing junction less than 5 pF and capacitive loads smaller than 100 pF. If any of these conditions are not met, it becomes necessary to overcompensate the amplifier with a larger compensation capacitor. Alternately, lead capacitors can be used in the feedback network to negate the effect of stray capacitance and large feedback resistors or an RC network can be added to isolate capacitive loads. Although the LM101A is relatively unaffected by supply bypassing, this cannot be ignored altogether. Generally it is necessary to bypass the supplies to ground at least once on every circuit card, and more bypass points may be required if more than five amplifiers are used. When feed-forward compensation is employed, however, it is advisable to bypass the supply leads of each amplifier with low inductance capacitors because of the higher frequencies involved. Typical Applications (3) Standard Compensation and Offset Balancing Circuit (3) Pin connections shown are for 8-pin packages. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN 15 LM101AJAN SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 www.ti.com Fast Voltage Follower Power Bandwidth: 15 kHz Slew Rate: 1V/s Fast Summing Amplifier Power Bandwidth: 250 kHz Small Signal Bandwiidth: 3.5 MHz Slew Rate: 10V/s Bilateral Current Source R3 = R4 + R5 R1 = R2 16 Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 Fast AC/DC Converter Feedforward compensation can be used to make a fast full wave rectifier without a filter. Instrumentation Amplifier R1 = R4; R2 = R3 *, Matching determines CMRR. Integrator with Bias Current Compensation Voltage Comparator for Driving RTL Logic or High Current Driver *Adjust for zero integrator drift. Current drift typically 0.1 nA/C over 0C to +70C temperature range. Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN 17 LM101AJAN SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 www.ti.com Low Frequency Square Wave Generator Voltage Comparator for Driving DTL or TTL Integrated Circuits Low Drift Sample and Hold *Polycarbonate-dielectric capacitor 18 Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN LM101AJAN www.ti.com SNOSAJ8A - JANUARY 2006 - REVISED MARCH 2013 REVISION HISTORY SECTION Date Released Revision Section Originator Changes 01/05/06 A New Release to corporate format L. Lytle 1 MDS datasheets converted into one Corp. datasheet format. MJLM101A-X Rev 1A0 datasheet will be archived. 03/20/13 A All - Changed layout of National Data Sheet to TI format Submit Documentation Feedback Copyright (c) 2006-2013, Texas Instruments Incorporated Product Folder Links: LM101AJAN 19 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) (3) Top-Side Markings (4) JL101ABCA ACTIVE CDIP J 14 25 TBD Call TI Call TI -55 to 125 JL101ABCA JM38510/10103BCA Q JL101ABGA ACTIVE TO-99 LMC 8 20 TBD Call TI Call TI -55 to 125 JL101ABGA JM38510/10103BGA Q ACO JM38510/10103BGA Q >T JL101ABPA ACTIVE CDIP NAB 8 40 TBD Call TI Call TI -55 to 125 JL101ABPA Q JM38510/ 10103BPA ACO 10103BPA >T JM38510/10103BCA ACTIVE CDIP J 14 25 TBD Call TI Call TI -55 to 125 JL101ABCA JM38510/10103BCA Q JM38510/10103BGA ACTIVE TO-99 LMC 8 20 TBD Call TI Call TI -55 to 125 JL101ABGA JM38510/10103BGA Q ACO JM38510/10103BGA Q >T JM38510/10103BPA ACTIVE CDIP NAB 8 40 TBD Call TI Call TI -55 to 125 JL101ABPA Q JM38510/ 10103BPA ACO 10103BPA >T M38510/10103BCA ACTIVE CDIP J 14 25 TBD Call TI Call TI -55 to 125 JL101ABCA JM38510/10103BCA Q M38510/10103BGA ACTIVE TO-99 LMC 8 20 TBD Call TI Call TI -55 to 125 JL101ABGA JM38510/10103BGA Q ACO JM38510/10103BGA Q >T M38510/10103BPA ACTIVE CDIP NAB 8 40 TBD Call TI Call TI -55 to 125 JL101ABPA Q JM38510/ 10103BPA ACO 10103BPA >T (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA NAB0008A J08A (Rev M) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated