DIM200PLM33-A000 DIM200PLM33-A000 IGBT Chopper Module Preliminary Information Replaces issue April 2003, version DS5597-1.1 FEATURES 10s Short Circuit Withstand High Thermal Cycling Capability Non Punch Through Silicon Isolated MMC Base with AlN Substrates DS5597-2.0 May 2003 KEY PARAMETERS VCES VCE(sat) * IC IC(PK) (typ) (max) (max) 3300V 3.2V 200A 400A *(measured at the power busbars and not the auxiliary terminals) APPLICATIONS Choppers Traction Auxiliaries 1(A/C2) The Powerline range of high power modules includes half bridge, chopper, dual, single and bi-directional switch configurations covering voltages from 600V to 3300V and currents up to 2400A. 2(K) 3(E2) 8(C2) 7(E2) 6(G2) The DIM200PLM33-A000 is a 3300V, n channel enhancement mode insulated gate bipolar transistor (IGBT) chopper module configured with the lower arm of the bridge controlled. The IGBT has a wide reverse bias safe operating area (RBSOA) plus full 10s short circuit withstand. This device is optimised for applications requiring high thermal cycling capability. Fig. 1 Chopper circuit diagram - lower arm control The module incorporates an electrically isolated base plate and low inductance construction enabling circuit designers to optimise circuit layouts and utilise grounded heat sinks for safety. ORDERING INFORMATION Order As: DIM200PLM33-A000 Note: When ordering, please use the whole part number. Outline type code: P (See package details for further information) Fig. 2 Electrical connections - (not to scale) Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. www.dynexsemi.com 1/6 DIM200PLM33-A000 ABSOLUTE MAXIMUM RATINGS Stresses above those listed under 'Absolute Maximum Ratings' may cause permanent damage to the device. In extreme conditions, as with all semiconductors, this may include potentially hazardous rupture of the package. Appropriate safety precautions should always be followed. Exposure to Absolute Maximum Ratings may affect device reliability. Tcase = 25C unless stated otherwise Symbol Test Conditions Parameter VCES Collector-emitter voltage VGES Gate-emitter voltage VGE = 0V - Max. Units 3300 V 20 V Continuous collector current Tcase = 85C 200 A IC(PK) Peak collector current 1ms, Tcase = 115C 400 A Pmax Max. transistor power dissipation Tcase = 25C, Tj = 150C 2608 W Visol Isolation voltage - per module Commoned terminals to base plate. AC RMS, 1 min, 50Hz 6000 V QPD Partial discharge - per module IEC1287. V1 = 2450V, V2 = 1800V, 50Hz RMS 10 pC IC THERMAL AND MECHANICAL RATINGS Internal insulation material: Baseplate material: Creepage distance: Clearance: CTI (Critical Tracking Index): AlN AlSiC 33mm 20mm 175 Symbol Parameter Rth(j-c) Thermal resistance - transistor (IGBT arm) Test Conditions Continuous dissipation - Min. Typ. Max. Units - - 48 C/kW junction to case Rth(j-c) Rth(c-h) Tj Tstg - 2/6 Thermal resistance - diode (IGBT arm) Continuous dissipation - - - 96 C/kW Thermal resistance - diode (diode arm) junction to case - - 96 C/kW Thermal resistance - case to heatsink Mounting torque 5Nm - - 16 C/kW (per module) (with mounting grease) Junction temperature Transistor - - 150 C Diode - - 125 C -40 - 125 C Mounting - M6 - - 5 Nm Electrical connections - M5 - - 4 Nm - Storage temperature range Screw torque Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. www.dynexsemi.com DIM200PLM33-A000 ELECTRICAL CHARACTERISTICS Tcase = 25C unless stated otherwise. Parameter Symbol Test Conditions Min. Typ. Max. Units Collector cut-off current VGE = 0V, VCE = VCES - - 1 mA (IGBT arm) VGE = 0V, VCE = VCES, Tcase = 125C - - 15 mA Gate leakage current (IGBT arm) VGE = 20V, VCE = 0V - - 2 A VGE(TH) Gate threshold voltage (IGBT arm) IC =20mA, VGE = VCE 4.5 5.5 6.5 V VCE(sat) Collector-emitter saturation voltage VGE = 15V, IC = 200A - 3.2 - V (IGBT arm) VGE = 15V, IC = 200A, , Tcase = 125C - 4.0 - V Diode forward current (IGBT arm) DC - 200 - A Diode forward current (diode arm) DC - 200 - A Diode maximum forward current tp = 1ms - 400 - A tp = 1ms - 400 - A IF = 200A (IGBT arm) - 2.5 - V IF = 200A (Diode arm) - 2.5 - V IF = 200A, Tcase = 125C (IGBT arm) - 2.5 - V IF = 200A, Tcase = 125C (diode arm) - 2.5 - V ICES IGES IF IFM (IGBT arm) Diode maximum forward current (diode arm) VF Diode forward voltage Cies Input capacitance (IGBT arm) VCE = 25V, VGE = 0V, f = 1MHz - 45 - nF Cres Reverse transfer capacitance (IGBT arm) VCE = 25V, VGE = 0V, f = 1MHz - 2.5 - nF LM Module inductance - per switch - - 30 - nH Internal transistor resistance (IGBT arm) - - 0.54 - m RINT SCData Short circuit. ISC Tj = 125C, VCC = 2500V, I1 1300 A tp 10s, VCE(max) = VCES - L*. di/dt I2 1100 A IEC 60747-9 Note: Measured at the power busbars and not the auxiliary terminals) L* is the circuit inductance + LM Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. www.dynexsemi.com 3/6 DIM200PLM33-A000 ELECTRICAL CHARACTERISTICS - IGBT ARM Tcase = 25C unless stated otherwise Min. Typ. Max. Units IC = 200A - 1300 - ns Fall time VGE = 15V - 200 - ns EOFF Turn-off energy loss VCE = 1800V - 170 - mJ td(on) Turn-on delay time RG(ON) = RG(OFF) =10 - 640 - ns Rise time Cge = 33nF - 250 - ns EON Turn-on energy loss L ~ 100nH - 290 - mJ Qg Gate charge - 6 - C Qrr Diode reverse recovery charge IF = 200A, VR = 1800V, - 115 - C Irr Diode reverse current dIF/dt = 1100A/s - 165 - A - 130 - mJ Min. Typ. Max. Units IC = 200A - 1600 - ns Fall time VGE = 15V - 250 - ns EOFF Turn-off energy loss VCE = 1800V - 240 - mJ td(on) Turn-on delay time RG(ON) = RG(OFF) =10 - 640 - ns Rise time Cge = 33nF - 300 - ns EON Turn-on energy loss L ~ 100nH - 420 - mJ Qrr Diode reverse recovery charge IF = 200A, VR = 1800V, - 190 - C Irr Diode reverse current dIF/dt = 1000A/s - 185 - A - 220 - mJ Parameter Symbol td(off) tf tr EREC Turn-off delay time Test Conditions Diode reverse recovery energy Tcase = 125C unless stated otherwise Parameter Symbol td(off) tf tr EREC 4/6 Turn-off delay time Diode reverse recovery energy Test Conditions Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. www.dynexsemi.com DIM200PLM33-A000 PACKAGE DETAILS For further package information, please visit our website or contact Customer Services. All dimensions in mm, unless stated otherwise. DO NOT SCALE. Nominal weight: 750g Module outline type code: P Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. www.dynexsemi.com 5/6 POWER ASSEMBLY CAPABILITY The Power Assembly group was set up to provide a support service for those customers requiring more than the basic semiconductor, and has developed a flexible range of heatsink and clamping systems in line with advances in device voltages and current capability of our semiconductors. We offer an extensive range of air and liquid cooled assemblies covering the full range of circuit designs in general use today. The Assembly group offers high quality engineering support dedicated to designing new units to satisfy the growing needs of our customers. Using the latest CAD methods our team of design and applications engineers aim to provide the Power Assembly Complete Solution (PACs). HEATSINKS The Power Assembly group has its own proprietary range of extruded aluminium heatsinks which have been designed to optimise the performance of Dynex semiconductors. Data with respect to air natural, forced air and liquid cooling (with flow rates) is available on request. For further information on device clamps, heatsinks and assemblies, please contact your nearest sales representative or Customer Services. http://www.dynexsemi.com e-mail: power_solutions@dynexsemi.com HEADQUARTERS OPERATIONS DYNEX SEMICONDUCTOR LTD Doddington Road, Lincoln. Lincolnshire. LN6 3LF. United Kingdom. Tel: +44-(0)1522-500500 Fax: +44-(0)1522-500550 CUSTOMER SERVICE Tel: +44 (0)1522 502753 / 502901. Fax: +44 (0)1522 500020 SALES OFFICES Benelux, Italy & Switzerland: Tel: +33 (0)1 64 66 42 17. Fax: +33 (0)1 64 66 42 19. France: Tel: +33 (0)2 47 55 75 52. Fax: +33 (0)2 47 55 75 59. Germany, Northern Europe, Spain & Rest Of World: Tel: +44 (0)1522 502753 / 502901. Fax: +44 (0)1522 500020 North America: Tel: (440) 259-2060. Fax: (440) 259-2059. Tel: (949) 733-3005. Fax: (949) 733-2986. These offices are supported by Representatives and Distributors in many countries world-wide. (c) Dynex Semiconductor 2003 TECHNICAL DOCUMENTATION - NOT FOR RESALE. PRODUCED IN UNITED KINGDOM Datasheet Annotations: Dynex Semiconductor annotate datasheets in the top right hard corner of the front page, to indicate product status. The annotations are as follows:Target Information: This is the most tentative form of information and represents a very preliminary specification. No actual design work on the product has been started. Preliminary Information: The product is in design and development. The datasheet represents the product as it is understood but details may change. Advance Information: The product design is complete and final characterisation for volume production is well in hand. No Annotation: The product parameters are fixed and the product is available to datasheet specification. This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request. All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners. www.dynexsemi.com