PCA2129 Automotive accurate RTC with integrated quartz crystal Rev. 5 -- 19 December 2014 Product data sheet 1. General description The PCA2129 is a CMOS1 Real Time Clock (RTC) and calendar with an integrated Temperature Compensated Crystal (Xtal) Oscillator (TCXO) and a 32.768 kHz quartz crystal optimized for very high accuracy and very low power consumption. The PCA2129 has a selectable I2C-bus or SPI-bus, a backup battery switch-over circuit, a programmable watchdog function, a timestamp function, and many other features. For a selection of NXP Real-Time Clocks, see Table 83 on page 73 2. Features and benefits 1. AEC-Q100 compliant for automotive applications Operating temperature range from 40 C to +85 C Temperature Compensated Crystal Oscillator (TCXO) with integrated capacitors Typical accuracy: 3 ppm from 30 C to +80 C Integration of a 32.768 kHz quartz crystal and oscillator in the same package Provides year, month, day, weekday, hours, minutes, seconds, and leap year correction Timestamp function with interrupt capability detection of two different events on one multilevel input pin (for example, for tamper detection) Two line bidirectional 400 kHz Fast-mode I2C-bus interface 3 line SPI-bus with separate data input and output (maximum speed 6.5 Mbit/s) Battery backup input pin and switch-over circuitry Battery backed output voltage Battery low detection function Power-On Reset Override (PORO) Oscillator stop detection function Interrupt output (open-drain) Programmable 1 second or 1 minute interrupt Programmable watchdog timer with interrupt Programmable alarm function with interrupt capability Programmable square output Clock operating voltage: 1.8 V to 4.2 V Low supply current: typical 0.70 A at VDD = 3.3 V The definition of the abbreviations and acronyms used in this data sheet can be found in Section 21. PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 3. Applications Electronic metering for electricity, water, and gas Precision timekeeping Access to accurate time of the day GPS equipment to reduce time to first fix Applications that require an accurate process timing Products with long automated unattended operation time 4. Ordering information Table 1. Ordering information Type number Package PCA2129T Name Description Version SO16 plastic small outline package; 16 leads; SOT162-1 body width 7.5 mm 4.1 Ordering options Table 2. Ordering options Product type number Orderable part number Sales item (12NC) Delivery form IC revision PCA2129T/Q900/2 PCA2129T/Q900/2,51 tape and reel, 13 inch, dry pack 2 935296923518 5. Marking Table 3. PCA2129 Product data sheet Marking codes Product type number Marking code PCA2129T/Q900/2 PCA2129T/Q All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 2 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 6. Block diagram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ig 1. Block diagram of PCA2129 PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 3 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 7. Pinning information 7.1 Pinning 6&/ 6', 9'' 9%$7 %%6 6'2 6'$&( ,)6 76 QF &/.287 QF 966 ,17 3&$7 QF QF DDD Top view. For mechanical details, see Figure 47. Fig 2. Pin configuration for PCA2129 (SO16) DDD Fig 3. Position of the stubs from the package assembly process After lead forming and cutting, there remain stubs from the package assembly process. These stubs are present at the edge of the package as illustrated in Figure 3. The stubs are at an electrical potential. To avoid malfunction of the PCA2129, it has to be ensured that they are not shorted with another electrical potential (e.g. by condensation). PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 4 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 7.2 Pin description Table 4. Pin description of PCA2129 Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Pin Description SCL 1 combined serial clock input for both I2C-bus and SPI-bus SDI 2 serial data input for SPI-bus connect to pin VSS if I2C-bus is selected SDO 3 serial data output for SPI-bus, push-pull SDA/CE 4 combined serial data input and output for the I2C-bus and chip enable input (active LOW) for the SPI-bus IFS 5 interface selector input connect to pin VSS to select the SPI-bus connect to pin BBS to select the I2C-bus TS 6 timestamp input (active LOW) with 200 k internal pull-up resistor (RPU) CLKOUT 7 clock output (open-drain) VSS 8 ground supply voltage n.c. 9 to 12 not connected; do not connect; do not use as feed through INT 13 interrupt output (open-drain; active LOW) BBS 14 output voltage (battery backed) VBAT 15 battery supply voltage (backup) VDD 16 supply voltage connect to VSS if battery switch over is not used PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 5 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8. Functional description The PCA2129 is a Real Time Clock (RTC) and calendar with an on-chip Temperature Compensated Crystal (Xtal) Oscillator (TCXO) and a 32.768 kHz quartz crystal integrated into the same package (see Section 8.3.3). Address and data are transferred by a selectable 400 kHz Fast-mode I2C-bus or a 3 line SPI-bus with separate data input and output (see Section 9). The maximum speed of the SPI-bus is 6.5 Mbit/s. The PCA2129 has a backup battery input pin and backup battery switch-over circuit which monitors the main power supply. The backup battery switch-over circuit automatically switches to the backup battery when a power failure condition is detected (see Section 8.5.1). Accurate timekeeping is maintained even when the main power supply is interrupted. A battery low detection circuit monitors the status of the battery (see Section 8.5.2). When the battery voltage drops below a certain threshold value, a flag is set to indicate that the battery must be replaced soon. This ensures the integrity of the data during periods of battery backup. 8.1 Register overview The PCA2129 contains an auto-incrementing address register: the built-in address register will increment automatically after each read or write of a data byte up to the register 1Bh. After register 1Bh, the auto-incrementing will wrap around to address 00h (see Figure 4). DGGUHVVUHJLVWHU K K K DXWRLQFUHPHQW K K $K %K Fig 4. ZUDSDURXQG DDM Handling address registers * The first three registers (memory address 00h, 01h, and 02h) are used as control registers (see Section 8.2). * The memory addresses 03h through to 09h are used as counters for the clock function (seconds up to years). The date is automatically adjusted for months with fewer than 31 days, including corrections for leap years. The clock can operate in 12-hour mode with an AM/PM indication or in 24-hour mode (see Section 8.8). * The registers at addresses 0Ah through 0Eh define the alarm function. It can be selected that an interrupt is generated when an alarm event occurs (see Section 8.9). * The register at address 0Fh defines the temperature measurement period and the clock out mode. The temperature measurement can be selected from every 4 minutes (default) down to every 30 seconds (see Table 14). CLKOUT frequencies of PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 6 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 32.768 kHz (default) down to 1 Hz for use as system clock, microcontroller clock, and so on, can be chosen (see Table 15). * The registers at addresses 10h and 11h are used for the watchdog timer functions. The watchdog timer has four selectable source clocks allowing for timer periods from less than 1 ms to greater than 4 hours (see Table 52). An interrupt is generated when the watchdog times out. * The registers at addresses 12h to 18h are used for the timestamp function. When the trigger event happens, the actual time is saved in the timestamp registers (see Section 8.11). * The register at address 19h is used for the correction of the crystal aging effect (see Section 8.4.1). * The registers at addresses 1Ah and 1Bh are for internal use only. * The registers Seconds, Minutes, Hours, Days, Months, and Years are all coded in Binary Coded Decimal (BCD) format to simplify application use. Other registers are either bit-wise or standard binary. When one of the RTC registers is written or read, the content of all counters is temporarily frozen. This prevents a faulty writing or reading of the clock and calendar during a carry condition (see Section 8.8.8). PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 7 of 84 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCA2129 Product data sheet Table 5. Register overview Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as T must always be written with logic 0. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Address Register name Bit 7 6 5 4 3 2 1 Reset value Reference 0 Control registers 00h Control_1 EXT_ TEST T STOP TSF1 POR_ OVRD 12_24 MI SI 0000 1000 Table 7 on page 10 01h Control_2 MSF WDTF TSF2 AF T TSIE AIE T 0000 0000 Table 9 on page 11 02h Control_3 BTSE BF BLF BIE BLIE 0000 0000 Table 11 on page 12 PWRMNG[2:0] Time and date registers Seconds OSF SECONDS (0 to 59) 1XXX XXXX Table 22 on page 25 04h Minutes - MINUTES (0 to 59) - XXX XXXX Table 25 on page 26 05h Hours - - - - XX XXXX Table 27 on page 27 06h Days - - 07h Weekdays - - - 08h Months - - - 09h Years AMPM HOURS (1 to 12) in 12-hour mode HOURS (0 to 23) in 24-hour mode - - XX XXXX DAYS (1 to 31) - - XX XXXX Table 29 on page 27 - - - - - XXX Table 31 on page 28 - - - X XXXX Table 34 on page 29 YEARS (0 to 99) XXXX XXXX Table 37 on page 30 - - WEEKDAYS (0 to 6) MONTHS (1 to 12) Alarm registers 0Ah Second_alarm AE_S SECOND_ALARM (0 to 59) 1XXX XXXX Table 39 on page 33 0Bh Minute_alarm AE_M MINUTE_ALARM (0 to 59) 1XXX XXXX Table 41 on page 33 0Ch Hour_alarm AE_H 1 - XX XXXX Table 43 on page 34 - Day_alarm AE_D - 0Eh Weekday_alarm AE_W - HOUR_ALARM (1 to 12) in 12-hour mode HOUR_ALARM (0 to 23) in 24-hour mode 1 - XX XXXX DAY_ALARM (1 to 31) 1 - XX XXXX Table 45 on page 34 - - - WEEKDAY_ALARM (0 to 6) 1 - - - - XXX Table 47 on page 35 OTPR - - COF[2:0] 00X - - 000 Table 13 on page 12 TI_TP - - 000 - - - 11 Table 49 on page 36 XXXX XXXX Table 51 on page 36 00 - X XXXX Table 58 on page 41 CLKOUT control register 0Fh CLKOUT_ctl TCR[1:0] Watchdog registers 10h Watchdg_tim_ctl 11h Watchdg_tim_val WD_CD T - WATCHDG_TIM_VAL[7:0] TF[1:0] Timestamp registers 12h Timestp_ctl TSM TSOFF - 1_O_16_TIMESTP[4:0] PCA2129 8 of 84 (c) NXP Semiconductors N.V. 2014. All rights reserved. 0Dh AMPM Automotive accurate RTC with integrated quartz crystal Rev. 5 -- 19 December 2014 All information provided in this document is subject to legal disclaimers. 03h xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Address Register name Bit 13h Sec_timestp - 14h Min_timestp - 15h Hour_timestp - - 16h Day_timestp - - 17h Mon_timestp - - 18h Year_timestp 7 6 5 Reset value Reference SECOND_TIMESTP (0 to 59) - XXX XXXX Table 60 on page 41 MINUTE_TIMESTP (0 to 59) - XXX XXXX Table 62 on page 42 - - XX XXXX Table 64 on page 42 4 AMPM 3 2 1 0 HOUR_TIMESTP (1 to 12) in 12-hour mode - - XX XXXX DAY_TIMESTP (1 to 31) - - XX XXXX Table 66 on page 43 - - - X XXXX Table 68 on page 43 XXXX XXXX Table 70 on page 43 - - - - 1000 Table 17 on page 14 MONTH_TIMESTP (1 to 12) YEAR_TIMESTP (0 to 99) Aging offset register 19h Aging_offset - - - - AO[3:0] Internal registers 1Ah Internal_reg - - - - - - - - ---- ---- - 1Bh Internal_reg - - - - - - - - ---- ---- - PCA2129 9 of 84 (c) NXP Semiconductors N.V. 2014. All rights reserved. Automotive accurate RTC with integrated quartz crystal Rev. 5 -- 19 December 2014 All information provided in this document is subject to legal disclaimers. HOUR_TIMESTP (0 to 23) in 24-hour mode - NXP Semiconductors PCA2129 Product data sheet Table 5. Register overview ...continued Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as T must always be written with logic 0. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.2 Control registers The first 3 registers of the PCA2129, with the addresses 00h, 01h, and 02h, are used as control registers. 8.2.1 Register Control_1 Table 6. Control_1 - control and status register 1 (address 00h) bit allocation Bits labeled as T must always be written with logic 0. Bit Symbol 7 6 5 4 3 2 1 0 EXT_ TEST T STOP TSF1 POR_ OVRD 12_24 MI SI 0 0 0 0 1 0 0 0 Reset value Table 7. Control_1 - control and status register 1 (address 00h) bit description Bits labeled as T must always be written with logic 0. Bit Symbol Value Description Reference 7 EXT_TEST 0 normal mode Section 8.13 1 external clock test mode 6 T 0 unused - 5 STOP 0 RTC source clock runs Section 8.14 1 RTC clock is stopped; RTC divider chain flip-flops are asynchronously set logic 0; CLKOUT at 32.768 kHz, 16.384 kHz, or 8.192 kHz is still available 4 TSF1 0 no timestamp interrupt generated Section 8.11.1 1 flag set when TS input is driven to an intermediate level between power supply and ground; flag must be cleared to clear interrupt 3 POR_OVRD 0 Power-On Reset Override (PORO) facility disabled; Section 8.7.2 1 Power-On Reset Override (PORO) sequence reception enabled 0 24-hour mode selected 1 12-hour mode selected Table 27, Table 43, Table 64 0 minute interrupt disabled Section 8.12.1 1 minute interrupt enabled 0 second interrupt disabled 1 second interrupt enabled set logic 0 for normal operation 2 1 0 12_24 MI SI PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 10 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.2.2 Register Control_2 Table 8. Control_2 - control and status register 2 (address 01h) bit allocation Bits labeled as T must always be written with logic 0. Bit Symbol 7 6 5 4 3 2 1 0 MSF WDTF TSF2 AF T TSIE AIE T 0 0 0 0 0 0 0 0 Reset value Table 9. Control_2 - control and status register 2 (address 01h) bit description Bits labeled as T must always be written with logic 0. Bit Symbol Value Description Reference 7 MSF 0 no minute or second interrupt generated Section 8.12 1 flag set when minute or second interrupt generated; flag must be cleared to clear interrupt 6 WDTF 0 no watchdog timer interrupt or reset generated 1 flag set when watchdog timer interrupt or reset generated; Section 8.12.3 flag cannot be cleared by command (read-only) 5 TSF2 0 no timestamp interrupt generated Section 8.11.1 1 flag set when TS input is driven to ground; flag must be cleared to clear interrupt 4 AF 0 no alarm interrupt generated 1 flag set when alarm triggered; Section 8.9.6 flag must be cleared to clear interrupt 3 T 2 TSIE 1 0 AIE T PCA2129 Product data sheet 0 unused Section 8.12.5 0 no interrupt generated from timestamp flag 1 interrupt generated when timestamp flag set 0 no interrupt generated from the alarm flag 1 interrupt generated when alarm flag set 0 unused All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 Section 8.12.4 - (c) NXP Semiconductors N.V. 2014. All rights reserved. 11 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.2.3 Register Control_3 Table 10. Control_3 - control and status register 3 (address 02h) bit allocation Bit 7 6 Symbol PWRMNG[2:0] Reset value Table 11. 5 0 0 0 4 3 2 1 0 BTSE BF BLF BIE BLIE 0 0 0 0 0 Control_3 - control and status register 3 (address 02h) bit description Bit Symbol Value Description Reference 7 to 5 PWRMNG[2:0] see Table 19 control of the battery switch-over, battery low detection, and extra power fail detection functions Section 8.5 4 BTSE 0 no timestamp when battery switch-over occurs Section 8.11.4 1 time-stamped when battery switch-over occurs 0 no battery switch-over interrupt generated 1 flag set when battery switch-over occurs; 3 BF Section 8.5.1 and Section 8.11.4 flag must be cleared to clear interrupt 2 BLF 0 battery status ok; Section 8.5.2 no battery low interrupt generated 1 battery status low; flag cannot be cleared by command 1 0 BIE BLIE 0 no interrupt generated from the battery flag (BF) 1 interrupt generated when BF is set 0 no interrupt generated from battery low flag (BLF) 1 interrupt generated when BLF is set Section 8.12.6 Section 8.12.7 8.3 Register CLKOUT_ctl Table 12. CLKOUT_ctl - CLKOUT control register (address 0Fh) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 Symbol 6 5 TCR[1:0] Reset value 0 0 4 3 OTPR - - X - - 2 1 0 COF[2:0] 0 0 0 Table 13. CLKOUT_ctl - CLKOUT control register (address 0Fh) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Description 7 to 6 TCR[1:0] see Table 14 temperature measurement period 5 OTPR 0 no OTP refresh 1 OTP refresh performed 4 to 3 - - unused 2 to 0 COF[2:0] see Table 15 CLKOUT frequency selection PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 12 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.3.1 Temperature compensated crystal oscillator The frequency of tuning fork quartz crystal oscillators is temperature-dependent. In the PCA2129, the frequency deviation caused by temperature variation is corrected by adjusting the load capacitance of the crystal oscillator. The load capacitance is changed by switching between two load capacitance values using a modulation signal with a programmable duty cycle. In order to compensate the spread of the quartz parameters every chip is factory calibrated. The frequency accuracy can be evaluated by measuring the frequency of the square wave signal available at the output pin CLKOUT. However, the selection of fCLKOUT = 32.768 kHz (default value) leads to inaccurate measurements. Accurate frequency measurement occurs when fCLKOUT = 16.384 kHz or lower is selected (see Table 15). 8.3.1.1 Temperature measurement The PCA2129 has a temperature sensor circuit used to perform the temperature compensation of the frequency. The temperature is measured immediately after power-on and then periodically with a period set by the temperature conversion rate TCR[1:0] in the register CLKOUT_ctl. Table 14. Temperature measurement period TCR[1:0] Temperature measurement period [1] 00 4 min 01 2 min 10 1 min 11 30 seconds [1] Default value. 8.3.2 OTP refresh Each IC is calibrated during production and testing of the device. The calibration parameters are stored on EPROM cells called One Time Programmable (OTP) cells. It is recommended to process an OTP refresh once after the power is up and the oscillator is operating stable. The OTP refresh takes less than 100 ms to complete. To perform an OTP refresh, bit OTPR has to be cleared (set to logic 0) and then set to logic 1 again. 8.3.3 Clock output A programmable square wave is available at pin CLKOUT. Operation is controlled by the COF[2:0] control bits in register CLKOUT_ctl. Frequencies of 32.768 kHz (default) down to 1 Hz can be generated for use as system clock, microcontroller clock, charge pump input, or for calibrating the oscillator. CLKOUT is an open-drain output and enabled at power-on. When disabled, the output is high-impedance. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 13 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 15. CLKOUT frequency selection CLKOUT frequency (Hz) Typical duty cycle[1] 32768 60 : 40 to 40 : 60 001 16384 50 : 50 010 8192 50 : 50 011 4096 50 : 50 100 2048 50 : 50 101 1024 50 : 50 110 1 50 : 50 111 CLKOUT = high-Z - COF[2:0] [2][3] 000 [1] Duty cycle definition: % HIGH-level time : % LOW-level time. [2] Default value. [3] The specified accuracy of the RTC can be only achieved with CLKOUT frequencies not equal to 32.768 kHz or if CLKOUT is disabled. The duty cycle of the selected clock is not controlled, however, due to the nature of the clock generation all but the 32.768 kHz frequencies are 50 : 50. 8.4 Register Aging_offset Table 16. Aging_offset - crystal aging offset register (address 19h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bit 7 6 5 4 Symbol - - - - Reset value - - - - 3 2 1 0 0 0 AO[3:0] 1 0 Table 17. Aging_offset - crystal aging offset register (address 19h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bit Symbol Value Description 7 to 4 - - unused 3 to 0 AO[3:0] see Table 18 aging offset value 8.4.1 Crystal aging correction The PCA2129 has an offset register Aging_offset to correct the crystal aging effects2. The accuracy of the frequency of a quartz crystal depends on its aging. The aging offset adds an adjustment, positive or negative, in the temperature compensation circuit which allows correcting the aging effect. At 25 C, the aging offset bits allow a frequency correction of typically 1 ppm per AO[3:0] value, from 7 ppm to +8 ppm. 2. For further information, refer to the application note Ref. 3 "AN11186". PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 14 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 18. Frequency correction at 25C, typical AO[3:0] Decimal Binary 0 0000 +8 1 0001 +7 2 0010 +6 3 0011 +5 4 0100 +4 5 0101 +3 6 0110 +2 7 0111 Product data sheet +1 [1] 0 8 1000 9 1001 1 10 1010 2 11 1011 3 12 1100 4 13 1101 5 14 1110 6 15 1111 7 [1] PCA2129 ppm Default value. All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 15 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.5 Power management functions The PCA2129 has two power supplies: VDD -- the main power supply VBAT -- the battery backup supply Internally, the PCA2129 is operating with the internal operating voltage Voper(int) which is also available as VBBS on the battery backed output voltage pin, BBS. Depending on the condition of the main power supply and the selected power management function, Voper(int) is either on the potential of VDD or VBAT (see Section 8.5.3). Two power management functions are implemented: Battery switch-over function -- monitoring the main power supply VDD and switching to VBAT in case a power fail condition is detected (see Section 8.5.1). Battery low detection function -- monitoring the status of the battery, VBAT (see Section 8.5.2). The power management functions are controlled by the control bits PWRMNG[2:0] (see Table 19) in register Control_3 (see Table 11): Table 19. Power management control bit description PWRMNG[2:0] Function [1] 000 battery switch-over function is enabled in standard mode; battery low detection function is enabled 001 battery switch-over function is enabled in standard mode; battery low detection function is disabled 010 battery switch-over function is enabled in standard mode; battery low detection function is disabled 011 battery switch-over function is enabled in direct switching mode; battery low detection function is enabled 100 battery switch-over function is enabled in direct switching mode; battery low detection function is disabled 101 battery switch-over function is enabled in direct switching mode; battery low detection function is disabled [2] 111 battery switch-over function is disabled, only one power supply (VDD); battery low detection function is disabled PCA2129 Product data sheet [1] Default value. [2] When the battery switch-over function is disabled, the PCA2129 works only with the power supply VDD. VBAT must be put to ground and the battery low detection function is disabled. All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 16 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.5.1 Battery switch-over function The PCA2129 has a backup battery switch-over circuit which monitors the main power supply VDD. When a power failure condition is detected, it automatically switches to the backup battery. One of two operation modes can be selected: Standard mode -- the power failure condition happens when: VDD < VBAT AND VDD < Vth(sw)bat Vth(sw)bat is the battery switch threshold voltage. Typical value is 2.5 V. The battery switch-over in standard mode works only for VDD > 2.5 V Direct switching mode -- the power failure condition happens when VDD < VBAT. Direct switching from VDD to VBAT without requiring VDD to drop below Vth(sw)bat When a power failure condition occurs and the power supply switches to the battery, the following sequence occurs: 1. The battery switch flag BF (register Control_3) is set logic 1. 2. An interrupt is generated if the control bit BIE (register Control_3) is enabled (see Section 8.12.6). 3. If the control bit BTSE (register Control_3) is logic 1, the timestamp registers store the time and date when the battery switch occurred (see Section 8.11.4). 4. The battery switch flag BF is cleared by command; it must be cleared to clear the interrupt. The interface is disabled in battery backup operation: * Interface inputs are not recognized, preventing extraneous data being written to the device * Interface outputs are high-impedance For further information about I2C-bus communication and battery backup operation, see Section 9.3 on page 56. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 17 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.5.1.1 Standard mode If VDD > VBAT OR VDD > Vth(sw)bat: Voper(int) is at VDD potential. If VDD < VBAT AND VDD < Vth(sw)bat: Voper(int) is at VBAT potential. EDFNXSEDWWHU\RSHUDWLRQ 9'' 9RSHU LQW 9%$7 9RSHU LQW LQWHUQDORSHUDWLQJYROWDJH 9RSHU LQW 9WK VZ EDW 9 9'' 9 %) ,17 FOHDUHGYLDLQWHUIDFH DDM Vth(sw)bat is the battery switch threshold voltage. Typical value is 2.5 V. In standard mode, the battery switch-over works only for VDD > 2.5 V. VDD may be lower than VBAT (for example VDD = 3 V, VBAT = 4.1 V). Fig 5. PCA2129 Product data sheet Battery switch-over behavior in standard mode with bit BIE set logic 1 (enabled) All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 18 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.5.1.2 Direct switching mode If VDD > VBAT: Voper(int) is at VDD potential. If VDD < VBAT: Voper(int) is at VBAT potential. The direct switching mode is useful in systems where VDD is always higher than VBAT. This mode is not recommended if the VDD and VBAT values are similar (for example, VDD = 3.3 V, VBAT 3.0 V). In direct switching mode, the power consumption is reduced compared to the standard mode because the monitoring of VDD and Vth(sw)bat is not performed. EDFNXSEDWWHU\RSHUDWLRQ 9'' 9RSHU LQW 9%$7 9RSHU LQW LQWHUQDORSHUDWLQJYROWDJH 9RSHU LQW 9WK VZ EDW 9 9'' 9 %) ,17 FOHDUHGYLDLQWHUIDFH DDM Fig 6. 8.5.1.3 Battery switch-over behavior in direct switching mode with bit BIE set logic 1 (enabled) Battery switch-over disabled: only one power supply (VDD) When the battery switch-over function is disabled: * * * * PCA2129 Product data sheet The power supply is applied on the VDD pin The VBAT pin must be connected to ground Voper(int) is at VDD potential The battery flag (BF) is always logic 0 All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 19 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.5.1.4 Battery switch-over architecture The architecture of the battery switch-over circuit is shown in Figure 7. FRPSDUDWRUV ORJLF VZLWFKHV 9'' 9WK VZ EDW 9'' 9RSHU LQW /2*,& 9WK VZ EDW 9%$7 9%$7 DDJ Fig 7. Battery switch-over circuit, simplified block diagram Voper(int) is at VDD or VBAT potential. Remark: It has to be assured that there are decoupling capacitors on the pins VDD, VBAT, and BBS. 8.5.2 Battery low detection function The PCA2129 has a battery low detection circuit which monitors the status of the battery VBAT. When VBAT drops below the threshold value Vth(bat)low (typically 2.5 V), the BLF flag (register Control_3) is set to indicate that the battery is low and that it must be replaced. Monitoring of the battery voltage also occurs during battery operation. An unreliable battery cannot prevent that the supply voltage drops below Vlow (typical 1.2 V) and with that the data integrity gets lost. (For further information about Vlow see Section 8.6.) When VBAT drops below the threshold value Vth(bat)low, the following sequence occurs (see Figure 8): 1. The battery low flag BLF is set logic 1. 2. An interrupt is generated if the control bit BLIE (register Control_3) is enabled (see Section 8.12.7). 3. The flag BLF remains logic 1 until the battery is replaced. BLF cannot be cleared by command. It is automatically cleared by the battery low detection circuit when the battery is replaced or when the voltage rises again above the threshold value. This could happen if a super capacitor is used as a backup source and the main power is applied again. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 20 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 9'' 9RSHU LQW LQWHUQDORSHUDWLQJYROWDJH 9RSHU LQW 9%$7 9WK EDW ORZ 9 9%$7 %/) ,17 DDM Fig 8. Battery low detection behavior with bit BLIE set logic 1 (enabled) 8.5.3 Battery backup supply The VBBS voltage on the output pin BBS is at the same potential as the internal operating voltage Voper(int), depending on the selected battery switch-over function mode: Table 20. Output pin BBS Battery switch-over function mode Conditions Potential of Voper(int) and VBBS standard VDD > VBAT OR VDD > Vth(sw)bat VDD VDD < VBAT AND VDD < Vth(sw)bat VBAT direct switching VDD > VBAT VDD VDD < VBAT VBAT disabled only VDD available, VBAT must be put to ground VDD The output pin BBS can be used as a supply for external devices with battery backup needs, such as SRAM (see Ref. 3 "AN11186"). For this case, Figure 9 shows the typical driving capability when VBBS is driven from VDD. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 21 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal DDM 9%%6 9'' P9 9'' 9 9'' 9 9'' 9 ,%%6 P$ Fig 9. Typical driving capability of VBBS: (VBBS VDD) with respect to the output load current IBBS 8.6 Oscillator stop detection function The PCA2129 has an on-chip oscillator detection circuit which monitors the status of the oscillation: whenever the oscillation stops, a reset occurs and the oscillator stop flag OSF (in register Seconds) is set logic 1. * Power-on: a. The oscillator is not running, the chip is in reset (OSF is logic 1). b. When the oscillator starts running and is stable after power-on, the chip exits from reset. c. The flag OSF is still logic 1 and can be cleared (OSF set logic 0) by command. * Power supply failure: a. When the power supply of the chip drops below a certain value (Vlow), typically 1.2 V, the oscillator stops running and a reset occurs. b. When the power supply returns to normal operation, the oscillator starts running again, the chip exits from reset. c. The flag OSF is still logic 1 and can be cleared (OSF set logic 0) by command. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 22 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 9'' 9RSHU LQW 9'' 9RSHU LQW 9%$7 9%$7 9WK VZ EDW 9 9'' 9'' EDWWHU\GLVFKDUJH 9ORZ 9 9RSHU LQW 9%$7 966 966 26) DDM (1) Theoretical state of the signals since there is no power. (2) The oscillator stop flag (OSF), set logic 1, indicates that the oscillation has stopped and a reset has occurred since the flag was last cleared (OSF set logic 0). In this case, the integrity of the clock information is not guaranteed. The OSF flag is cleared by command. Fig 10. Power failure event due to battery discharge: reset occurs 8.7 Reset function The PCA2129 has a Power-On Reset (POR) and a Power-On Reset Override (PORO) function implemented. 8.7.1 Power-On Reset (POR) The POR is active whenever the oscillator is stopped. The oscillator is considered to be stopped during the time between power-on and stable crystal resonance (see Figure 11). This time may be in the range of 200 ms to 2 s depending on temperature and supply voltage. Whenever an internal reset occurs, the oscillator stop flag is set (OSF set logic 1). The OTP refresh (see Section 8.3.2 on page 13) should ideally be executed as the first instruction after start-up and also after a reset due to an oscillator stop. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 23 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal FKLSLQUHVHW FKLSQRWLQUHVHW FKLSIXOO\RSHUDWLYH &/.287 DYDLODEOH 9'' RVFLOODWLRQ LQWHUQDO UHVHW 2735 W DDD Fig 11. Dependency between POR and oscillator After POR, the following mode is entered: * * * * * 32.768 kHz CLKOUT active Power-On Reset Override (PORO) available to be set 24-hour mode is selected Battery switch-over is enabled Battery low detection is enabled The register values after power-on are shown in Table 5 on page 8. 8.7.2 Power-On Reset Override (PORO) The POR duration is directly related to the crystal oscillator start-up time. Due to the long start-up times experienced by these types of circuits, a mechanism has been built in to disable the POR and therefore speed up the on-board test of the device. 26&,//$725 6&/ 6'$&( 5(6(7 29(55,'( RVFVWRSSHG VWRSSHG UXQQLQJ UHVHW RYHUULGHLQDFWLYH RYHUULGHDFWLYH &/($5 325B295' FOHDURYHUULGHPRGH RYHUULGHSRVVLEOH DDM Fig 12. Power-On Reset (POR) system The setting of the PORO mode requires that POR_OVRD in register Control_1 is set logic 1 and that the signals at the interface pins SDA/CE and SCL are toggled as illustrated in Figure 13. All timings shown are required minimum. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 24 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal SRZHUXS PV PLQLPXPQV PLQLPXPQV 6'$&( 6&/ UHVHWRYHUULGH DDM Fig 13. Power-On Reset Override (PORO) sequence, valid for both I2C-bus and SPI-bus Once the override mode is entered, the device is immediately released from the reset state and the set-up operation can commence. The PORO mode is cleared by writing logic 0 to POR_OVRD. POR_OVRD must be logic 1 before a re-entry into the override mode is possible. Setting POR_OVRD logic 0 during normal operation has no effect except to prevent accidental entry into the PORO mode. 8.8 Time and date function Most of these registers are coded in the Binary Coded Decimal (BCD) format. 8.8.1 Register Seconds Table 21. Seconds - seconds and clock integrity register (address 03h) bit allocation Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 Symbol 6 5 4 OSF Reset value 1 3 2 1 0 X X X SECONDS (0 to 59) X X X X Table 22. Seconds - seconds and clock integrity register (address 03h) bit description Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol 7 OSF Value Place value Description 0 - clock integrity is guaranteed 1 - clock integrity is not guaranteed: oscillator has stopped and chip reset has occurred since flag was last cleared 6 to 4 SECONDS 3 to 0 PCA2129 Product data sheet 0 to 5 ten's place 0 to 9 unit place actual seconds coded in BCD format All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 25 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 23. Seconds coded in BCD format Seconds value in decimal Upper-digit (ten's place) Digit (unit place) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 00 0 0 0 0 0 0 0 01 0 0 0 0 0 0 1 02 0 0 0 0 0 1 0 : : : : : : : : 09 0 0 0 1 0 0 1 10 0 0 1 0 0 0 0 : : : : : : : : 58 1 0 1 1 0 0 0 59 1 0 1 1 0 0 1 8.8.2 Register Minutes Table 24. Minutes - minutes register (address 04h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 Symbol - Reset value - 6 5 4 3 2 1 0 X X X MINUTES (0 to 59) X X X X Table 25. Minutes - minutes register (address 04h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 - - - unused 6 to 4 MINUTES 0 to 5 ten's place actual minutes coded in BCD format 0 to 9 unit place 3 to 0 PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 26 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.8.3 Register Hours Table 26. Hours - hours register (address 05h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 5 Symbol - - AMPM 4 3 2 1 0 HOURS (1 to 12) in 12-hour mode HOURS (0 to 23) in 24-hour mode Reset value - - X X X X X X Table 27. Hours - hours register (address 05h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 to 6 - - - unused - indicates AM 12-hour mode[1] 5 AMPM 0 1 - indicates PM 4 HOURS 0 to 1 ten's place 0 to 9 unit place actual hours coded in BCD format when in 12-hour mode 0 to 2 ten's place 0 to 9 unit place 3 to 0 24-hour mode[1] 5 to 4 HOURS 3 to 0 [1] actual hours coded in BCD format when in 24-hour mode Hour mode is set by the bit 12_24 in register Control_1 (see Table 7). 8.8.4 Register Days Table 28. Days - days register (address 06h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 Symbol - - Reset value - - Table 29. 5 4 3 2 X X X X 0 X X Days - days register (address 06h) bit description Bit Symbol Value Place value Description 7 to 6 - - - unused 5 to 4 DAYS[1] 0 to 3 ten's place actual day coded in BCD format 0 to 9 unit place 3 to 0 [1] 1 DAYS (1 to 31) If the year counter contains a value which is exactly divisible by 4, including the year 00, the RTC compensates for leap years by adding a 29th day to February. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 27 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.8.5 Register Weekdays Table 30. Weekdays - weekdays register (address 07h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 5 4 3 Symbol - - - - - Reset value - - - - - 2 1 0 WEEKDAYS (0 to 6) X X X Table 31. Weekdays - weekdays register (address 07h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Description 7 to 3 - - unused 2 to 0 WEEKDAYS 0 to 6 actual weekday value, see Table 32 Although the association of the weekdays counter to the actual weekday is arbitrary, the PCA2129 assumes that Sunday is 000 and Monday is 001 for the purpose of determining the increment for calendar weeks. Table 32. Weekday assignments Day[1] 2 1 0 Sunday 0 0 0 Monday 0 0 1 Tuesday 0 1 0 Wednesday 0 1 1 Thursday 1 0 0 Friday 1 0 1 Saturday 1 1 0 [1] PCA2129 Product data sheet Bit Definition may be reassigned by the user. All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 28 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.8.6 Register Months Table 33. Months - months register (address 08h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 5 Symbol - - - Reset value - - - 4 3 2 1 0 X X MONTHS (1 to 12) X X X Table 34. Months - months register (address 08h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 to 5 - - - unused 4 MONTHS 0 to 1 ten's place actual month coded in BCD format, see Table 35 0 to 9 unit place 3 to 0 Table 35. Month PCA2129 Product data sheet Month assignments in BCD format Upper-digit (ten's place) Digit (unit place) Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 January 0 0 0 0 1 February 0 0 0 1 0 March 0 0 0 1 1 April 0 0 1 0 0 May 0 0 1 0 1 June 0 0 1 1 0 July 0 0 1 1 1 August 0 1 0 0 0 September 0 1 0 0 1 October 1 0 0 0 0 November 1 0 0 0 1 December 1 0 0 1 0 All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 29 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.8.7 Register Years Table 36. Years - years register (address 09h) bit allocation Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 5 X X X Symbol 4 3 2 1 0 X X X YEARS (0 to 99) Reset value X X Table 37. Years - years register (address 09h) bit description Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 to 4 YEARS 0 to 9 ten's place 0 to 9 unit place 3 to 0 actual year coded in BCD format 8.8.8 Setting and reading the time Figure 14 shows the data flow and data dependencies starting from the 1 Hz clock tick. During read/write operations, the time counting circuits (memory locations 03h through 09h) are blocked. This prevents * Faulty reading of the clock and calendar during a carry condition * Incrementing the time registers during the read cycle +]WLFN 6(&21'6 0,187(6 BKRXUPRGH +2856 /($3<($5 &$/&8/$7,21 '$<6 :((.'$< 0217+6 <($56 DDI Fig 14. Data flow of the time function After this read/write access is completed, the time circuit is released again. Any pending request to increment the time counters that occurred during the read/write access is serviced. A maximum of 1 request can be stored; therefore, all accesses must be completed within 1 second (see Figure 15). PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 30 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal WV 67$57 6/$9($''5(66 '$7$ '$7$ 6723 DDD Fig 15. Access time for read/write operations As a consequence of this method, it is very important to make a read or write access in one go. That is, setting or reading seconds through to years should be made in one single access. Failing to comply with this method could result in the time becoming corrupted. As an example, if the time (seconds through to hours) is set in one access and then in a second access the date is set, it is possible that the time may increment between the two accesses. A similar problem exists when reading. A roll-over may occur between reads thus giving the minutes from one moment and the hours from the next. Therefore it is advised to read all time and date registers in one access. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 31 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.9 Alarm function When one or more of the alarm bit fields are loaded with a valid second, minute, hour, day, or weekday and its corresponding alarm enable bit (AE_x) is logic 0, then that information is compared with the actual second, minute, hour, day, and weekday (see Figure 16). H[DPSOH FKHFNQRZVLJQDO $(B6 $(B6 6(&21'$/$50 6(&21'7,0( $(B0 0,187($/$50 0,187(7,0( $(B+ +285$/$50 VHWDODUPIODJ$) +2857,0( $(B' '$<$/$50 '$<7,0( $(B: :((.'$<$/$50 DDD :((.'$<7,0( (1) Only when all enabled alarm settings are matching. Fig 16. Alarm function block diagram The generation of interrupts from the alarm function is described in Section 8.12.4. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 32 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.9.1 Register Second_alarm Table 38. Second_alarm - second alarm register (address 0Ah) bit allocation Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol 7 5 4 X X X AE_S Reset value Table 39. 6 1 3 2 1 0 X X SECOND_ALARM (0 to 59) X X Second_alarm - second alarm register (address 0Ah) bit description Bit Symbol Value Place value Description 7 AE_S 0 - second alarm is enabled 1 - second alarm is disabled 0 to 5 ten's place second alarm information coded in BCD format 0 to 9 unit place 6 to 4 SECOND_ALARM 3 to 0 8.9.2 Register Minute_alarm Table 40. Minute_alarm - minute alarm register (address 0Bh) bit allocation Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol 7 6 5 4 AE_M Reset value 1 3 2 1 0 X X MINUTE_ALARM (0 to 59) X X X X X Table 41. Minute_alarm - minute alarm register (address 0Bh) bit description Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 AE_M 0 - minute alarm is enabled 1 - minute alarm is disabled 0 to 5 ten's place minute alarm information coded in BCD format 0 to 9 unit place 6 to 4 MINUTE_ALARM 3 to 0 PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 33 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.9.3 Register Hour_alarm Table 42. Hour_alarm - hour alarm register (address 0Ch) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol 7 6 5 AE_H - AMPM 4 3 2 1 0 HOUR_ALARM (1 to 12) in 12-hour mode HOUR_ALARM (0 to 23) in 24-hour mode Reset value 1 - X X X X X X Table 43. Hour_alarm - hour alarm register (address 0Ch) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 AE_H 0 - hour alarm is enabled 1 - hour alarm is disabled - - unused 0 - indicates AM 1 - indicates PM 0 to 1 ten's place 0 to 9 unit place hour alarm information coded in BCD format when in 12-hour mode 0 to 2 ten's place 0 to 9 unit place 6 - 12-hour 5 mode[1] AMPM 4 HOUR_ALARM 3 to 0 24-hour mode[1] 5 to 4 HOUR_ALARM 3 to 0 [1] hour alarm information coded in BCD format when in 24-hour mode Hour mode is set by the bit 12_24 in register Control_1. 8.9.4 Register Day_alarm Table 44. Day_alarm - day alarm register (address 0Dh) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol 7 6 AE_D - 1 - Reset value 5 4 3 2 1 0 X X DAY_ALARM (1 to 31) X X X X Table 45. Day_alarm - day alarm register (address 0Dh) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 AE_D 0 - day alarm is enabled 1 - day alarm is disabled 6 - - - unused 5 to 4 DAY_ALARM 0 to 3 ten's place day alarm information coded in BCD format 0 to 9 unit place 3 to 0 PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 34 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.9.5 Register Weekday_alarm Table 46. Weekday_alarm - weekday alarm register (address 0Eh) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol 7 6 5 4 3 2 AE_W - - - - WEEKDAY_ALARM (0 to 6) 1 - - - - X Reset value 1 X 0 X Table 47. Weekday_alarm - weekday alarm register (address 0Eh) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Description 7 AE_W 0 weekday alarm is enabled 1 weekday alarm is disabled 6 to 3 - - unused 2 to 0 WEEKDAY_ALARM 0 to 6 weekday alarm information 8.9.6 Alarm flag When all enabled comparisons first match, the alarm flag AF (register Control_2) is set. AF remains set until cleared by command. Once AF has been cleared, it will only be set again when the time increments to match the alarm condition once more. For clearing the flags, see Section 8.10.5 Alarm registers which have their alarm enable bit AE_x at logic 1 are ignored. PLQXWHVFRXQWHU PLQXWHDODUP $) ,17ZKHQ$,( DDI Example where only the minute alarm is used and no other interrupts are enabled. Fig 17. Alarm flag timing diagram 8.10 Timer functions The PCA2129 has a watchdog timer function. The timer can be switched on and off by using the control bit WD_CD in the register Watchdg_tim_ctl. The watchdog timer has four selectable source clocks. It can, for example, be used to detect a microcontroller with interrupt and reset capability which is out of control (see Section 8.10.3) To control the timer function and timer output, the registers Control_2, Watchdg_tim_ctl, and Watchdg_tim_val are used. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 35 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.10.1 Register Watchdg_tim_ctl Table 48. Watchdg_tim_ctl - watchdog timer control register (address 10h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as T must always be written with logic 0. Bit Symbol 7 6 5 4 3 2 WD_CD T TI_TP - - - 0 0 0 - - - Reset value 1 0 TF[1:0] 1 1 Table 49. Watchdg_tim_ctl - watchdog timer control register (address 10h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as T must always be written with logic 0. Bit Symbol Value Description 7 WD_CD 0 watchdog timer disabled 1 watchdog timer enabled; the interrupt pin INT is activated when timed out 6 T 0 unused 5 TI_TP 0 the interrupt pin INT is configured to generate a permanent active signal when MSF is set 1 the interrupt pin INT is configured to generate a pulsed signal when MSF flag is set (see Figure 20) - unused 4 to 2 - 1 to 0 TF[1:0] timer source clock for watchdog timer 00 4.096 kHz 01 64 Hz 10 1 Hz 11 1 60 Hz 8.10.2 Register Watchdg_tim_val Table 50. Watchdg_tim_val - watchdog timer value register (address 11h) bit allocation Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 5 4 Symbol 3 2 1 0 X X X WATCHDG_TIM_VAL[7:0] Reset value X X X X X Table 51. Watchdg_tim_val - watchdog timer value register (address 11h) bit description Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Description 7 to 0 WATCHDG_TIM_ VAL[7:0] 00 to FF timer period in seconds: n TimerPeriod = -------------------------------------------------------------SourceClockFrequency where n is the timer value PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 36 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 52. Programmable watchdog timer TF[1:0] Timer source clock frequency Units Minimum timer period (n = 1) Units Maximum timer period (n = 255) Units 00 4.096 kHz 244 s 62.256 ms 01 64 Hz 15.625 ms 3.984 s 10 1 Hz 1 s 255 s 11 1 60 Hz 60 s 15300 s 8.10.3 Watchdog timer function The watchdog timer function is enabled or disabled by the WD_CD bit of the register Watchdg_tim_ctl (see Table 49). The 2 bits TF[1:0] in register Watchdg_tim_ctl determine one of the four source clock frequencies for the watchdog timer: 4.096 kHz, 64 Hz, 1 Hz, or 160 Hz (see Table 52). When the watchdog timer function is enabled, the 8-bit timer in register Watchdg_tim_val determines the watchdog timer period (see Table 52). The watchdog timer counts down from the software programmed 8-bit binary value n in register Watchdg_tim_val. When the counter reaches 1, the watchdog timer flag WDTF (register Control_2) is set logic 1 and an interrupt is generated. The counter does not automatically reload. When WD_CD is logic 0 (watchdog timer disabled) and the Microcontroller Unit (MCU) loads a watchdog timer value n: * the flag WDTF is reset * INT is cleared * the watchdog timer starts again Loading the counter with 0 will: * reset the flag WDTF * clear INT * stop the watchdog timer Remark: WDTF is read only and cannot be cleared by command. WDTF can be cleared by: * loading a value in register Watchdg_tim_val * reading of the register Control_2 Writing a logic 0 or logic 1 to WDTF has no effect. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 37 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 0&8 ZDWFKGRJ WLPHUYDOXH Q Q :'7) ,17 DDJ Counter reached 1, WDTF is logic 1, and an interrupt is generated. Fig 18. WD_CD set logic 1: watchdog activates an interrupt when timed out * When the watchdog timer counter reaches 1, the watchdog timer flag WDTF is set logic 1 * When a minute or second interrupt occurs, the minute/second flag MSF is set logic 1 (see Section 8.12.1). 8.10.4 Pre-defined timers: second and minute interrupt PCA2129 has two pre-defined timers which are used to generate an interrupt either once per second or once per minute (see Section 8.12.1). The pulse generator for the minute or second interrupt operates from an internal 64 Hz clock. It is independent of the watchdog timer. Each of these timers can be enabled by the bits SI (second interrupt) and MI (minute interrupt) in register Control_1. 8.10.5 Clearing flags The flags MSF, AF, and TSFx can be cleared by command. To prevent one flag being overwritten while clearing another, a logic AND is performed during the write access. A flag is cleared by writing logic 0 while a flag is not cleared by writing logic 1. Writing logic 1 results in the flag value remaining unchanged. Two examples are given for clearing the flags. Clearing a flag is made by a write command: * Bits labeled with - must be written with their previous values * Bits labeled with T have to be written with logic 0 * WDTF is read only and has to be written with logic 0 Repeatedly rewriting these bits has no influence on the functional behavior. Table 53. Register Control_2 PCA2129 Product data sheet Flag location in register Control_2 Bit 7 6 5 4 3 2 1 0 MSF WDTF TSF2 AF T - - T All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 38 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 54. Register Control_2 Example values in register Control_2 Bit 7 6 5 4 3 2 1 0 1 0 1 1 0 0 0 0 The following tables show what instruction must be sent to clear the appropriate flag. Table 55. Register Example to clear only AF (bit 4) Bit 7 Control_2 [1] 6 1 0 1 4 0 3 2 1 0 0 0[1] 0[1] 0 3 2 1 0 0 0[1] 0[1] 0 The bits labeled as - have to be rewritten with the previous values. Table 56. Register Example to clear only MSF (bit 7) Bit 7 Control_2 [1] 5 6 0 0 5 1 4 1 The bits labeled as - have to be rewritten with the previous values. 8.11 Timestamp function The PCA2129 has an active LOW timestamp input pin TS, internally pulled with an on-chip pull-up resistor to Voper(int). It also has a timestamp detection circuit which can detect two different events: 1. Input on pin TS is driven to an intermediate level between power supply and ground. 2. Input on pin TS is driven to ground. 9RSHU LQW 5 N 76 5 N SXVKEXWWRQ FRQQHFWHGWR FRYHU SXVKEXWWRQ FRQQHFWHGWR FRYHU 966 3&$ Q) DDD (1) When using switches or push-buttons, it is recommended to connect a 1 nF capacitance to the TS pin to ensure proper switching. Fig 19. Timestamp detection with two push-buttons on the TS pin (for example, for tamper detection) The timestamp function is enabled by default after power-on and it can be switched off by setting the control bit TSOFF (register Timestp_ctl). PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 39 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal A most common application of the timestamp function is described in Ref. 3 "AN11186". See Section 8.12.5 for a description of interrupt generation from the timestamp function. 8.11.1 Timestamp flag 1. When the TS input pin is driven to an intermediate level between the power supply and ground, either on the falling edge from VDD or on the rising edge from ground, then the following sequence occurs: a. The actual date and time are stored in the timestamp registers. b. The timestamp flag TSF1 (register Control_1) is set. c. If the TSIE bit (register Control_2) is active, an interrupt on the INT pin is generated. The TSF1 flag can be cleared by command. Clearing the flag clears the interrupt. Once TSF1 is cleared, it will only be set again when a new negative or positive edge on pin TS is detected. 2. When the TS input pin is driven to ground, the following sequence occurs: a. The actual date and time are stored in the timestamp registers. b. In addition to the TSF1 flag, the TSF2 flag (register Control_2) is set. c. If the TSIE bit is active, an interrupt on the INT pin is generated. The TSF1 and TSF2 flags can be cleared by command; clearing both flags clears the interrupt. Once TSF2 is cleared, it will only be set again when TS pin is driven to ground once again. 8.11.2 Timestamp mode The timestamp function has two different modes selected by the control bit TSM (timestamp mode) in register Timestp_ctl: * If TSM is logic 0 (default): in subsequent trigger events without clearing the timestamp flags, the last timestamp event is stored * If TSM is logic 1: in subsequent trigger events without clearing the timestamp flags, the first timestamp event is stored The timestamp function also depends on the control bit BTSE in register Control_3, see Section 8.11.4. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 40 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.11.3 Timestamp registers 8.11.3.1 Register Timestp_ctl Table 57. Timestp_ctl - timestamp control register (address 12h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol 7 6 5 TSM TSOFF - 0 0 - Reset value 4 3 2 1 0 X X 1_O_16_TIMESTP[4:0] X X X Table 58. Timestp_ctl - timestamp control register (address 12h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Description 7 TSM 0 in subsequent events without clearing the timestamp flags, the last event is stored 1 in subsequent events without clearing the timestamp flags, the first event is stored 0 timestamp function active 1 timestamp function disabled - unused 6 TSOFF 5 - 4 to 0 1_O_16_TIMESTP[4:0] 8.11.3.2 1 16 second timestamp information coded in BCD format Register Sec_timestp Table 59. Sec_timestp - second timestamp register (address 13h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 Symbol - Reset value - 6 5 X X 4 3 2 1 0 X X SECOND_TIMESTP (0 to 59) X X X Table 60. Sec_timestp - second timestamp register (address 13h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 - - - unused 6 to 4 SECOND_TIMESTP 0 to 5 ten's place second timestamp information coded in BCD format 0 to 9 unit place 3 to 0 PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 41 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.11.3.3 Register Min_timestp Table 61. Min_timestp - minute timestamp register (address 14h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 Symbol - Reset value - 6 5 4 3 2 1 0 X X MINUTE_TIMESTP (0 to 59) X X X X X Table 62. Min_timestp - minute timestamp register (address 14h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 - - - unused 6 to 4 MINUTE_TIMESTP 0 to 5 ten's place minute timestamp information coded in BCD format 0 to 9 unit place 3 to 0 8.11.3.4 Register Hour_timestp Table 63. Hour_timestp - hour timestamp register (address 15h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 5 Symbol - - AMPM 4 3 2 1 0 HOUR_TIMESTP (1 to 12) in 12-hour mode HOUR_TIMESTP (0 to 23) in 24-hour mode Reset value - - X X X X X X Table 64. Hour_timestp - hour timestamp register (address 15h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 to 6 - - - unused 0 - indicates AM 1 - indicates PM 0 to 1 ten's place 0 to 9 unit place hour timestamp information coded in BCD format when in 12-hour mode 0 to 2 ten's place 0 to 9 unit place 12-hour mode[1] 5 AMPM 4 HOUR_TIMESTP 3 to 0 24-hour 5 to 4 mode[1] HOUR_TIMESTP 3 to 0 [1] hour timestamp information coded in BCD format when in 24-hour mode Hour mode is set by the bit 12_24 in register Control_1. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 42 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.11.3.5 Register Day_timestp Table 65. Day_timestp - day timestamp register (address 16h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 Symbol - - Reset value - - 5 4 3 2 1 0 X X DAY_TIMESTP (1 to 31) X X X X Table 66. Day_timestp - day timestamp register (address 16h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 to 6 - - - unused 5 to 4 DAY_TIMESTP 0 to 3 ten's place day timestamp information coded in BCD format 0 to 9 unit place 3 to 0 8.11.3.6 Register Mon_timestp Table 67. Mon_timestp - month timestamp register (address 17h) bit allocation Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 5 Symbol - - - Reset value - - - 4 3 2 1 0 MONTH_TIMESTP (1 to 12) X X X X X Table 68. Mon_timestp - month timestamp register (address 17h) bit description Bit positions labeled as - are not implemented and return 0 when read. Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 to 5 - - - unused 4 MONTH_TIMESTP 0 to 1 ten's place month timestamp information coded in BCD format 0 to 9 unit place 3 to 0 8.11.3.7 Register Year_timestp Table 69. Year_timestp - year timestamp register (address 18h) bit allocation Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit 7 6 5 Symbol 4 3 2 1 0 X X X YEAR_TIMESTP (0 to 99) Reset value X X X X X Table 70. Year_timestp - year timestamp register (address 18h) bit description Bits labeled as X are undefined at power-on and unchanged by subsequent resets. Bit Symbol Value Place value Description 7 to 4 YEAR_TIMESTP 0 to 9 ten's place 0 to 9 unit place 3 to 0 PCA2129 Product data sheet year timestamp information coded in BCD format All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 43 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 8.11.4 Dependency between Battery switch-over and timestamp The timestamp function depends on the control bit BTSE in register Control_3: Table 71. Battery switch-over and timestamp BTSE BF Description 0 - [1] 0 [1] 1 the battery switch-over does not affect the timestamp registers If a battery switch-over event occurs: the timestamp registers store the time and date when the switch-over occurs; after this event occurred BF is set logic 1 1 the timestamp registers are not modified; in this condition subsequent battery switch-over events or falling edges on pin TS are not registered [1] Default value. 8.12 Interrupt output, INT PCA2129 has an interrupt output pin INT which is open-drain, active LOW (requiring a pull-up resistor if used). Interrupts may be sourced from different places: * * * * * * second or minute timer watchdog timer alarm timestamp battery switch-over battery low detection The control bit TI_TP (register Watchdg_tim_ctl) is used to configure whether the interrupts generated from the second/minute timer (flag MSF in register Control_2) are pulsed signals or a permanently active signal. All the other interrupt sources generate a permanently active interrupt signal which follows the status of the corresponding flags. When the interrupt sources are all disabled, INT remains high-impedance. * The flags MSF, AF, TSFx, and BF can be cleared by command. * The flag WDTF is read only. How it can be cleared is explained in Section 8.10.5. * The flag BLF is read only. It is cleared automatically from the battery low detection circuit when the battery is replaced. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 44 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 6, 6(&21'6&2817(5 0, 0,187(6&2817(5 06) 0,187( 6(&21')/$* 6(7 &/($5 WRLQWHUIDFH UHDG06) 38/6( *(1(5$725 75,**(5 &/($5 6,0, 7,B73 ,17SLQ IURPLQWHUIDFH FOHDU06) :'B&' :$7&+'2* &2817(5 0&8ORDGLQJ ZDWFKGRJFRXQWHU VHWDODUP IODJ$) :'7) :$7&+'2* 7,0(5)/$* 6(7 &/($5 WRLQWHUIDFH UHDG$) $,( 76)[7,0(67$03 )/$* 6(7 &/($5 WRLQWHUIDFH UHDG76)[ 76,( %)%$77(5< )/$* 6(7 &/($5 WRLQWHUIDFH UHDG%) %,( %/)%$77(5< /2:)/$* 6(7 &/($5 WRLQWHUIDFH UHDG%/) %/,( IURPLQWHUIDFH FOHDU76) VHWEDWWHU\ IODJ%) IURPLQWHUIDFH FOHDU%) VHWEDWWHU\ ORZIODJ%/) :'B&' $)$/$50 )/$* 6(7 &/($5 IURPLQWHUIDFH FOHDU$) VHWWLPHVWDPS IODJ76)[ WRLQWHUIDFH UHDG:'B&' IURPEDWWHU\ ORZGHWHFWLRQ FLUFXLWFOHDU%) DDM When SI, MI, WD_CD, AIE, TSIE, BIE, BLIE are all disabled, INT remains high-impedance. Fig 20. Interrupt block diagram 8.12.1 Minute and second interrupts Minute and second interrupts are generated by predefined timers. The timers can be enabled independently from one another by the bits MI and SI in register Control_1. However, a minute interrupt enabled on top of a second interrupt cannot be distinguishable since it occurs at the same time. The minute/second flag MSF (register Control_2) is set logic 1 when either the seconds or the minutes counter increments according to the enabled interrupt (see Table 72). The MSF flag can be cleared by command. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 45 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 72. Effect of bits MI and SI on pin INT and bit MSF MI SI Result on INT Result on MSF 0 0 no interrupt generated MSF never set 1 0 an interrupt once per minute MSF set when minutes counter increments 0 1 an interrupt once per second MSF set when seconds counter increments 1 1 an interrupt once per second MSF set when seconds counter increments When MSF is set logic 1: * If TI_TP is logic 1, the interrupt is generated as a pulsed signal. * If TI_TP is logic 0, the interrupt is permanently active signal that remains until MSF is cleared. VHFRQGVFRXQWHU PLQXWHVFRXQWHU ,17ZKHQ6,HQDEOHG 06)ZKHQ6,HQDEOHG ,17ZKHQRQO\0,HQDEOHG 06)ZKHQRQO\0,HQDEOHG DDI In this example, bit TI_TP is logic 1 and the MSF flag is not cleared after an interrupt. Fig 21. INT example for SI and MI when TI_TP is logic 1 VHFRQGVFRXQWHU PLQXWHVFRXQWHU ,17ZKHQ6,HQDEOH 06)ZKHQ6,HQDEOH ,17ZKHQRQO\0,HQDEOHG 06)ZKHQRQO\0,HQDEOHG DDJ In this example, bit TI_TP is logic 0 and the MSF flag is cleared after an interrupt. Fig 22. INT example for SI and MI when TI_TP is logic 0 PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 46 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal The pulse generator for the minute/second interrupt operates from an internal 64 Hz clock and generates a pulse of 164 seconds in duration. 8.12.2 INT pulse shortening If the MSF flag (register Control_2) is cleared before the end of the INT pulse, then the INT pulse is shortened. This allows the source of a system interrupt to be cleared immediately when it is serviced, that is, the system does not have to wait for the completion of the pulse before continuing; see Figure 23. Instructions for clearing the bit MSF can be found in Section 8.10.5. VHFRQGVFRXQWHU 06) ,17 6&/ WKFORFN LQVWUXFWLRQ &/($5,16758&7,21 DDI (1) Indicates normal duration of INT pulse. The timing shown for clearing bit MSF is also valid for the non-pulsed interrupt mode, that is, when TI_TP is logic 0, where the INT pulse may be shortened by setting both bits MI and SI logic 0. Fig 23. Example of shortening the INT pulse by clearing the MSF flag 8.12.3 Watchdog timer interrupts The generation of interrupts from the watchdog timer is controlled using the WD_CD bit (register Watchdg_tim_ctl). The interrupt is generated as an active signal which follows the status of the watchdog timer flag WDTF (register Control_2). No pulse generation is possible for watchdog timer interrupts. The interrupt is cleared when the flag WDTF is reset. WDTF is a read-only bit and cannot be cleared by command. Instructions for clearing it can be found in Section 8.10.5. 8.12.4 Alarm interrupts Generation of interrupts from the alarm function is controlled by the bit AIE (register Control_2). If AIE is enabled, the INT pin follows the status of bit AF (register Control_2). Clearing AF immediately clears INT. No pulse generation is possible for alarm interrupts. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 47 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal PLQXWHFRXQWHU PLQXWHDODUP $) ,17 6&/ WKFORFN LQVWUXFWLRQ &/($5,16758&7,21 DDI Example where only the minute alarm is used and no other interrupts are enabled. Fig 24. AF timing diagram 8.12.5 Timestamp interrupts Interrupt generation from the timestamp function is controlled using the TSIE bit (register Control_2). If TSIE is enabled, the INT pin follows the status of the flags TSFx. Clearing the flags TSFx immediately clears INT. No pulse generation is possible for timestamp interrupts. 8.12.6 Battery switch-over interrupts Generation of interrupts from the battery switch-over is controlled by the BIE bit (register Control_3). If BIE is enabled, the INT pin follows the status of bit BF in register Control_3 (see Table 71). Clearing BF immediately clears INT. No pulse generation is possible for battery switch-over interrupts. 8.12.7 Battery low detection interrupts Generation of interrupts from the battery low detection is controlled by the BLIE bit (register Control_3). If BLIE is enabled, the INT pin follows the status of bit BLF (register Control_3). The interrupt is cleared when the battery is replaced (BLF is logic 0) or when bit BLIE is disabled (BLIE is logic 0). BLF is read only and therefore cannot be cleared by command. 8.13 External clock test mode A test mode is available which allows on-board testing. In this mode, it is possible to set up test conditions and control the operation of the RTC. The test mode is entered by setting bit EXT_TEST logic 1 (register Control_1). Then pin CLKOUT becomes an input. The test mode replaces the internal clock signal (64 Hz) with the signal applied to pin CLKOUT. Every 64 positive edges applied to pin CLKOUT generate an increment of one second. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 48 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal The signal applied to pin CLKOUT should have a minimum pulse width of 300 ns and a maximum period of 1000 ns. The internal clock, now sourced from CLKOUT, is divided down by a 26 divider chain called prescaler (see Table 73). The prescaler can be set into a known state by using bit STOP. When bit STOP is logic 1, the prescaler is reset to 0. STOP must be cleared before the prescaler can operate again. From a stop condition, the first 1 second increment will take place after 32 positive edges on pin CLKOUT. Thereafter, every 64 positive edges cause a 1 second increment. Remark: Entry into test mode is not synchronized to the internal 64 Hz clock. When entering the test mode, no assumption as to the state of the prescaler can be made. Operating example: 1. Set EXT_TEST test mode (register Control_1, EXT_TEST is logic 1). 2. Set bit STOP (register Control_1, STOP is logic 1). 3. Set time registers to desired value. 4. Clear STOP (register Control_1, STOP is logic 0). 5. Apply 32 clock pulses to CLKOUT. 6. Read time registers to see the first change. 7. Apply 64 clock pulses to CLKOUT. 8. Read time registers to see the second change. Repeat 7 and 8 for additional increments. 8.14 STOP bit function The function of the STOP bit is to allow for accurate starting of the time circuits. STOP causes the upper part of the prescaler (F9 to F14) to be held in reset and thus no 1 Hz ticks are generated. The time circuits can then be set and will not increment until the STOP bit is released. STOP doesn't affect the CLKOUT signal but the output of the prescaler in the range of 32 Hz to 1 Hz (see Figure 25). /2:(535(6&$/(5 +] 26& +] ) +] ) 833(535(6&$/(5 +] +] ) +] ) ) ) ) ) 5(6 5(6 5(6 5(6 +]WLFN VWRS DDM Fig 25. STOP bit functional diagram The lower stages of the prescaler, F0 to F8, are not reset and because the I2C-bus and the SPI-bus are asynchronous to the crystal oscillator, the accuracy of restarting the time circuits is between 0 and one 64 Hz cycle (0.484375 s and 0.500000 s), see Table 73 and Figure 26. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 49 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 73. First increment of time circuits after stop release Bit STOP Prescaler bits[1] F0 to F8 - F9 to F14 1 Hz tick Time hh:mm:ss Comment 12:45:12 prescaler counting normally Clock is running normally 0 010000111-010100 STOP bit is activated by user. F0 to F8 are not reset and values cannot be predicted externally 1 xxxxxxxxx-000000 12:45:12 prescaler is reset; time circuits are frozen 08:00:00 prescaler is reset; time circuits are frozen 08:00:00 prescaler is now running New time is set by user 1 xxxxxxxxx-000000 STOP bit is released by user xxxxxxxxx-000000 0 xxxxxxxxx-100000 0 xxxxxxxxx-100000 0 xxxxxxxxx-110000 : : 0 111111111-111110 0 000000000-000001 08:00:01 0 100000000-000001 08:00:01 : : : 0 111111111-111111 08:00:01 0 000000000-000000 0 100000000-000000 : : : 0 111111111-111110 08:00:01 0 000000000-000001 08:00:02 V 0 08:00:00 08:00:00 08:00:00 : V 08:00:00 0 to 1 transition of F14 increments the time circuits 08:00:01 0 to 1 transition of F14 increments the time circuits DDM [1] F0 is clocked at 32.768 kHz. +] VWRSUHOHDVHG PVPV DDM Fig 26. STOP bit release timing PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 50 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 9. Interfaces The PCA2129 has an I2C-bus or SPI-bus interface using the same pins. The selection is done using the interface selection pin IFS (see Table 74). Table 74. Interface selection input pin IFS Pin Connection Bus interface Reference IFS VSS SPI-bus Section 9.1 BBS I2C-bus Section 9.2 9'' 9'' 6&/ 538 538 6', 6&/ 6'2 6'$ &( 9'' 6&/ 9'' 6&/ 6', 6', 6'2 %%6 6'2 6'$&( ,)6 %%6 6'$&( ,)6 3&$ 3&$ 966 966 966 966 DDD DDD To select the I2C-bus interface, pin IFS has to be connected to pin BBS. To select the SPI-bus interface, pin IFS has to be connected to pin VSS. b. I2C-bus interface selection a. SPI-bus interface selection Fig 27. Interface selection 9.1 SPI-bus interface Data transfer to and from the device is made by a 3 line SPI-bus (see Table 75). The data lines for input and output are split. The data input and output line can be connected together to facilitate a bidirectional data bus (see Figure 28). The SPI-bus is initialized whenever the chip enable line pin SDA/CE is inactive. 6', 6', 6'2 6'2 WZRZLUHPRGH VLQJOHZLUHPRGH DDL Fig 28. SDI, SDO configurations PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 51 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 75. Serial interface Symbol Function SDA/CE Description [1] chip enable input; active LOW when HIGH, the interface is reset; input may be higher than VDD SCL serial clock input when SDA/CE is HIGH, input may float; SDI serial data input when SDA/CE is HIGH, input may float; input may be higher than VDD input may be higher than VDD; input data is sampled on the rising edge of SCL SDO serial data output push-pull output; drives from VSS to Voper(int) (VBBS); output data is changed on the falling edge of SCL [1] The chip enable must not be wired permanently LOW. 9.1.1 Data transmission The chip enable signal is used to identify the transmitted data. Each data transfer is a whole byte, with the Most Significant Bit (MSB) sent first. The transmission is controlled by the active LOW chip enable signal SDA/CE. The first byte transmitted is the command byte. Subsequent bytes are either data to be written or data to be read (see Figure 29). GDWDEXV &200$1' '$7$ '$7$ '$7$ 6'$&( DDD Fig 29. Data transfer overview The command byte defines the address of the first register to be accessed and the read/write mode. The address counter will auto increment after every access and will reset to zero after the last valid register is accessed. The R/W bit defines if the following bytes are read or write information. Table 76. Command byte definition Bit Symbol 7 R/W 6 to 5 SA Value Description data read or write selection 0 write data 1 read data 01 subaddress; other codes will cause the device to ignore data transfer 4 to 0 PCA2129 Product data sheet RA 00h to 1Bh register address All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 52 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 5: 6$ DGGUK VHFRQGVGDWD%&' PLQXWHVGDWD%&' E E E E E E E E E E E E E E E E E E E E E E E E 6&/ 6', 6'$&( DGGUHVV [[ FRXQWHU DDM In this example, the Seconds register is set to 45 seconds and the Minutes register to 10 minutes. Fig 30. SPI-bus write example 5: 6$ DGGUK PRQWKVGDWD%&' \HDUVGDWD%&' E E E E E E E E E E E E E E E E E E E E E E E E 6&/ 6', 6'2 6'$&( DGGUHVV [[ FRXQWHU $ DDM In this example, the registers Months and Years are read. The pins SDI and SDO are not connected together. For this configuration, it is important that pin SDI is never left floating. It must always be driven either HIGH or LOW. If pin SDI is left open, high IDD currents may result. Fig 31. SPI-bus read example PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 53 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 9.2 I2C-bus interface The I2C-bus is for bidirectional, two-line communication between different ICs or modules. The two lines are a Serial DAta line (SDA) and a Serial CLock line (SCL). Both lines are connected to a positive supply by a pull-up resistor. Data transfer is initiated only when the bus is not busy. 9.2.1 Bit transfer One data bit is transferred during each clock pulse. The data on the SDA line remains stable during the HIGH period of the clock pulse as changes in the data line at this time are interpreted as control signals (see Figure 32). 6'$ 6&/ GDWDOLQH VWDEOH GDWDYDOLG FKDQJH RIGDWD DOORZHG PEF Fig 32. Bit transfer 9.2.2 START and STOP conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line, while the clock is HIGH, is defined as the START condition S. A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP condition P (see Figure 33). 6'$ 6'$ 6&/ 6&/ 6 3 67$57FRQGLWLRQ 6723FRQGLWLRQ PEF Fig 33. Definition of START and STOP conditions Remark: For the PCA2129, a repeated START is not allowed. Therefore a STOP has to be released before the next START. 9.2.3 System configuration A device generating a message is a transmitter; a device receiving a message is the receiver. The device that controls the message is the master; and the devices which are controlled by the master are the slaves. The PCA2129 can act as a slave transmitter and a slave receiver. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 54 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 6'$ 6&/ 0$67(5 75$160,77(5 5(&(,9(5 6/$9( 75$160,77(5 5(&(,9(5 6/$9( 5(&(,9(5 0$67(5 75$160,77(5 5(&(,9(5 0$67(5 75$160,77(5 PED Fig 34. System configuration 9.2.4 Acknowledge The number of data bytes transferred between the START and STOP conditions from transmitter to receiver is unlimited. Each byte of 8 bits is followed by an acknowledge cycle. * A slave receiver which is addressed must generate an acknowledge after the reception of each byte. * Also a master receiver must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. * The device that acknowledges must pull-down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse (set-up and hold times must be considered). * A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition. Acknowledgement on the I2C-bus is illustrated in Figure 35. GDWDRXWSXW E\WUDQVPLWWHU QRWDFNQRZOHGJH GDWDRXWSXW E\UHFHLYHU DFNQRZOHGJH 6&/IURP PDVWHU 6 67$57 FRQGLWLRQ FORFNSXOVHIRU DFNQRZOHGJHPHQW PEF Fig 35. Acknowledgement on the I2C-bus 9.2.5 I2C-bus protocol After a start condition, a valid hardware address has to be sent to a PCA2129 device. The appropriate I2C-bus slave address is 1010001. The entire I2C-bus slave address byte is shown in Table 77. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 55 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal I2C slave address byte Table 77. Slave address Bit 7 6 5 4 3 2 1 0 0 1 0 0 0 1 R/W MSB LSB 1 The R/W bit defines the direction of the following single or multiple byte data transfer (read is logic 1, write is logic 0). For the format and the timing of the START condition (S), the STOP condition (P), and the acknowledge (A) refer to the I2C-bus specification Ref. 13 "UM10204" and the characteristics table (Table 82). In the write mode, a data transfer is terminated by sending a STOP condition. A repeated START (Sr) condition is not applicable. DFNQRZOHGJH IURP3&$ 6 VODYHDGGUHVV DFNQRZOHGJH IURP3&$ DFNQRZOHGJH IURP3&$ $ $ $ WRQ GDWDE\WHV SOXV$&. UHJLVWHUDGGUHVV KWR%K ZULWHELW 3 6 6723 67$57 DDD Fig 36. Bus protocol, writing to registers DFNQRZOHGJH IURP3&$ 6 VODYHDGGUHVV DFNQRZOHGJH IURP3&$ $ $ UHJLVWHUDGGUHVV KWR%K ZULWHELW DFNQRZOHGJH IURP3&$ 6 VODYHDGGUHVV $ VHWUHJLVWHU DGGUHVV 3 6723 DFNQRZOHGJH IURPPDVWHU '$7$%<7( $ QRDFNQRZOHGJH /$67'$7$%<7( $ WRQ GDWDE\WHV SOXV$&. UHDGELW 3 UHDGUHJLVWHU GDWD DDD Fig 37. Bus protocol, reading from registers 9.3 Bus communication and battery backup operation To save power during battery backup operation (see Section 8.5.1), the bus interfaces are inactive. Therefore the communication via I2C- or SPI-bus should be terminated before the supply of the PCA2129 is switched from VDD to VBAT. Remark: If the I2C-bus communication was terminated uncontrolled, the I2C-bus has to be reinitialized by sending a STOP followed by a START after the device switched back from battery backup operation to VDD supply operation. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 56 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 10. Internal circuitry 9'' 6&/ 9%$7 %%6 6', 6'2 ,17 6'$&( ,)6 76 &/.287 966 3&$7 DDD Fig 38. Device diode protection diagram of PCA2129 11. Safety notes CAUTION This device is sensitive to ElectroStatic Discharge (ESD). Observe precautions for handling electrostatic sensitive devices. Such precautions are described in the ANSI/ESD S20.20, IEC/ST 61340-5, JESD625-A or equivalent standards. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 57 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 12. Limiting values Table 78. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VDD Conditions Min Max Unit supply voltage 0.5 +6.5 V IDD supply current 50 +50 mA Vi input voltage 0.5 +6.5 V II input current 10 +10 mA VO output voltage 0.5 +6.5 V IO output current at pin SDA/CE VBAT battery supply voltage Ptot total power dissipation 10 +10 mA 10 +20 mA 0.5 +6.5 V - 300 mW HBM [1] - 4000 V CDM [2] - 1250 V latch-up current [3] - 200 mA Tstg storage temperature [4] 55 +85 C Tamb ambient temperature 40 +85 C VESD Ilu electrostatic discharge voltage operating device [1] Pass level; Human Body Model (HBM) according to Ref. 7 "JESD22-A114". [2] Pass level; Charged-Device Model (CDM), according to Ref. 8 "JESD22-C101". [3] Pass level; latch-up testing according to Ref. 9 "JESD78" at maximum ambient temperature (Tamb(max)). [4] According to the store and transport requirements (see Ref. 14 "UM10569") the devices have to be stored at a temperature of +8 C to +45 C and a humidity of 25 % to 75 %. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 58 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 13. Static characteristics Table 79. Static characteristics VDD = 1.8 V to 4.2 V; VSS = 0 V; Tamb = 40 C to +85 C, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Supplies [1] VDD supply voltage 1.8 - 4.2 V VBAT battery supply voltage 1.8 - 4.2 V VDD(cal) calibration supply voltage - 3.3 - V Vlow low voltage - 1.2 - V IDD supply current SPI-bus (fSCL = 6.5 MHz) - - 800 A I2C-bus - - 200 A interface active; supplied by VDD (fSCL = 400 kHz) Hz)[2]; interface inactive (fSCL = 0 TCR[1:0] = 00 (see Table 13 on page 12) PWRMNG[2:0] = 111 (see Table 19 on page 16); TSOFF = 1 (see Table 58 on page 41); COF[2:0] = 111 (see Table 15 on page 14) VDD = 1.8 V - 470 - nA VDD = 3.3 V - 700 1500 nA VDD = 4.2 V - 800 - nA - nA PWRMNG[2:0] = 111 (see Table 19 on page 16); TSOFF = 1 (see Table 58 on page 41); COF[2:0] = 000 (see Table 15 on page 14) VDD = 1.8 V - 560 VDD = 3.3 V - 850 - nA VDD = 4.2 V - 1050 - nA PWRMNG[2:0] = 000 (see Table 19 on page 16); TSOFF = 0 (see Table 58 on page 41); COF[2:0] = 111 (see Table 15 on page 14) VDD or VBAT = 1.8 V [3] - 1750 - nA VDD or VBAT = 3.3 V [3] - 2150 - nA VDD or VBAT = 4.2 V [3] - 2350 3500 nA PWRMNG[2:0] = 000 (see Table 19 on page 16); TSOFF = 0 (see Table 58 on page 41); COF[2:0] = 000 (see Table 15 on page 14) IL(bat) battery leakage current PCA2129 Product data sheet VDD or VBAT = 1.8 V [3] - 1840 - nA VDD or VBAT = 3.3 V [3] - 2300 - nA VDD or VBAT = 4.2 V [3] - 2600 - nA - 50 100 nA VDD is active supply; VBAT = 3.0 V All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 59 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 79. Static characteristics ...continued VDD = 1.8 V to 4.2 V; VSS = 0 V; Tamb = 40 C to +85 C, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Power management Vth(sw)bat battery switch threshold voltage - 2.5 - V Vth(bat)low low battery threshold voltage - 2.5 - V 2.25 - 2.85 V Tamb = 25 C Inputs[4] VI input voltage 0.5 - VDD + 0.5 V VIL LOW-level input voltage - - 0.25VDD V - - 0.3VDD V Tamb = 20 C to +85 C; VDD > 2.0 V VIH HIGH-level input voltage ILI input leakage current 0.7VDD - - V - 0 - A 1 - +1 A - - 7 pF on pins CLKOUT, INT, referring to external pull-up 0.5 - +5.5 V on pin BBS 1.8 - 4.2 V VI = VDD or VSS post ESD event [5] input capacitance Ci Outputs output voltage VO on pin SDO 0.5 - VDD + 0.5 V VOH HIGH output voltage on pin SDO 0.8VDD - VDD V VOL LOW output voltage on pins CLKOUT, INT, and SDO VSS - 0.2VDD V IOL LOW-level output current output sink current; VOL = 0.4 V 3 17 - mA on all other outputs 1.0 - - mA on pin SDA/CE [6] IOH HIGH-level output current output source current; on pin SDO; VOH = 3.8 V; VDD = 4.2 V 1.0 - - mA ILO output leakage current VO = VDD or VSS - 0 - A 1 - +1 A post ESD event [1] For reliable oscillator start-up at power-on: VDD(po)min = VDD(min) + 0.3 V. [2] Timer source clock = 160 Hz, level of pins SDA/CE, SDI, and SCL is VDD or VSS. [3] When the device is supplied by the VBAT pin instead of the VDD pin, the current values for IBAT are as specified for IDD under the same conditions. [4] The I2C-bus and SPI-bus interfaces of PCA2129 are 5 V tolerant. [5] Tested on sample basis. [6] For further information, see Figure 39. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 60 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 13.1 Current consumption characteristics, typical DDO ,2/ P$ 9'' 9 Typical value; VOL = 0.4 V. Fig 39. IOL on pin SDA/CE DDM ,'' $ 9'' 9 9'' 9 7HPSHUDWXUH & CLKOUT disabled; PWRMNG[2:0] = 111; TSOFF = 1; TS input floating. Fig 40. IDD as a function of temperature PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 61 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal DDM ,'' $ &/.287HQDEOHGDW N+] &/.2872)) 9'' 9 a. PWRMNG[2:0] = 111; TSOFF = 1; Tamb = 25 C; TS input floating DDM ,'' $ &/.287HQDEOHGDW N+] &/.2872)) 9'' 9 b. PWRMNG[2:0] = 000; TSOFF = 0; Tamb = 25 C; TS input floating Fig 41. IDD as a function of VDD PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 62 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal ,'' $ 3:50*>@ DDD Interface inactive; Tamb = 25 C; VBAT = 0 V; default configuration. Description of the PWRMNG[2:0] settings, see Table 19 on page 16. (1) VDD = 1.8 V. (2) VDD = 3.3 V. (3) VDD = 4.2 V. (4) VDD or VBAT = 1.8 V. (5) VDD or VBAT = 3.3 V. (6) VDD or VBAT = 4.2 V. Fig 42. Typical IDD as a function of the power management settings PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 63 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 13.2 Frequency characteristics Table 80. Frequency characteristics VDD = 1.8 V to 4.2 V; VSS = 0 V; Tamb = +25 C, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fo output frequency on pin CLKOUT; VDD or VBAT = 3.3 V; COF[2:0] = 000; AO[3:0] = 1000 - 32.768 - kHz f/f frequency stability VDD or VBAT = 3.3 V fxtal/fxtal relative crystal frequency variation Tamb = +23 C (2 C) [1][2] - 3 5.8 ppm Tamb = 30 C to +80 C [1][2] - 3 8 ppm Tamb = 40 C to 30 C and Tamb = +80 C to +85 C [1][2] - 5 15 ppm [3] - - 3 ppm - - 8 ppm - 1 - ppm/V crystal aging first year ten years f/V [1] frequency variation with voltage on pin CLKOUT 1 ppm corresponds to a time deviation of 0.0864 seconds per day. [2] Only valid if CLKOUT frequencies are not equal to 32.768 kHz or if CLKOUT is disabled. [3] Not production tested. Effects of reflow soldering are included (see Ref. 3 "AN11186"). DDD )UHTXHQF\ VWDELOLW\ SSP SSP SSP SSP 7HPSHUDWXUH & (1) Typical temperature compensated frequency response. (2) Uncompensated typical tuning-fork crystal frequency. Fig 43. Typical characteristic of frequency with respect to temperature of PCA2129 PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 64 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 14. Dynamic characteristics 14.1 SPI-bus timing characteristics Table 81. SPI-bus characteristics VDD = 1.8 V to 4.2 V; VSS = 0 V; Tamb = 40 C to +85 C, unless otherwise specified. All timing values are valid within the operating supply voltage at ambient temperature and referenced to VIL and VIH with an input voltage swing of VSS to VDD (see Figure 44). Symbol Parameter Conditions VDD = 1.8 V VDD = 4.2 V Min Min Max Unit Max Pin SCL fclk(SCL) SCL clock frequency - 2.0 - 6.5 MHz tSCL SCL time 800 - 140 - ns tclk(H) clock HIGH time 100 - 70 - ns tclk(L) clock LOW time 400 - 70 - ns tr rise time for SCL signal - 100 - 100 ns tf fall time for SCL signal - 100 - 100 ns Pin SDA/CE tsu(CE_N) CE_N set-up time 60 - 30 - ns th(CE_N) CE_N hold time 40 - 25 - ns trec(CE_N) CE_N recovery time 100 - 30 - ns tw(CE_N) CE_N pulse width - 0.99 - 0.99 s Pin SDI tsu set-up time set-up time for SDI data 70 - 20 - ns th hold time hold time for SDI data 70 - 20 - ns SDO read delay time CL = 50 pF - 225 - 55 ns Pin SDO td(R)SDO tdis(SDO) SDO disable time tt(SDI-SDO) transition time from SDI to SDO [1] [1] to avoid bus conflict - 90 - 25 ns 0 - 0 - ns No load value; bus is held up by bus capacitance; use RC time constant with application values. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 65 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal WZ &(B1 &( WVX &(B1 WU WUHF &(B1 WI WFON 6&/ WK &(B1 6&/ WFON / WFON + :5,7( WVX WK 6', 6'2 5: 6$ 5$ E E E E E KLJK= 5($' 6', E WW 6',6'2 6'2 KLJK= WG 5 6'2 E WGLV 6'2 E E DDD Fig 44. SPI-bus timing PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 66 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 14.2 I2C-bus timing characteristics Table 82. I2C-bus characteristics All timing characteristics are valid within the operating supply voltage and ambient temperature range and reference to 30 % and 70 % with an input voltage swing of VSS to VDD (see Figure 45). Symbol Parameter Standard mode Fast-mode (Fm) Unit Min Max Min Max 0 100 0 400 kHz Pin SCL [1] fSCL SCL clock frequency tLOW LOW period of the SCL clock 4.7 - 1.3 - s tHIGH HIGH period of the SCL clock 4.0 - 0.6 - s Pin SDA/CE tSU;DAT data set-up time 250 - 100 - ns tHD;DAT data hold time 0 - 0 - ns Pins SCL and SDA/CE tBUF bus free time between a STOP and START condition 4.7 - 1.3 - s tSU;STO set-up time for STOP condition 4.0 - 0.6 - s tHD;STA hold time (repeated) START condition 4.0 - 0.6 - s tSU;STA set-up time for a repeated START condition 4.7 - 0.6 - s tr rise time of both SDA and SCL signals [2][3][4] - 1000 20 + 0.1Cb 300 ns tf fall time of both SDA and SCL signals [2][3][4] - 300 20 + 0.1Cb 300 ns tVD;ACK data valid acknowledge time [5] 0.1 3.45 0.1 0.9 s tVD;DAT data valid time [6] 300 - 75 - ns tSP pulse width of spikes that must be suppressed by the input filter [7] - 50 - 50 ns [1] The minimum SCL clock frequency is limited by the bus time-out feature which resets the serial bus interface if either the SDA or SCL is held LOW for a minimum of 25 ms. The bus time-out feature must be disabled for DC operation. [2] A master device must internally provide a hold time of at least 300 ns for the SDA signal (refer to the VIL of the SCL signal) in order to bridge the undefined region of the falling edge of SCL. [3] Cb is the total capacitance of one bus line in pF. [4] The maximum tf for the SDA and SCL bus lines is 300 ns. The maximum fall time for the SDA output stage, tf is 250 ns. This allows series protection resistors to be connected between the SDA/CE pin, the SCL pin, and the SDA/SCL bus lines without exceeding the maximum tf. [5] tVD;ACK is the time of the acknowledgement signal from SCL LOW to SDA (out) LOW. [6] tVD;DAT is the minimum time for valid SDA (out) data following SCL LOW. [7] Input filters on the SDA and SCL inputs suppress noise spikes of less than 50 ns. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 67 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 35272&2/ 67$57 &21',7,21 6 W6867$ %,7 06% $ W/2: %,7 /6% 5: %,7 $ W+,*+ $&.12:/('*( $ 6723 &21',7,21 3 I6&/ 6&/ W%8) WU WI 6'$ W+'67$ W68'$7 W+''$7 W9''$7 W68672 PEG Fig 45. I2C-bus timing diagram; rise and fall times refer to 30 % and 70 % PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 68 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 15. Application information Q) ) 9'' 6&/ 6', ,QWHUIDFH 6'2 Q) 9%$7 6'$&( %%6 ,& 63, 9'' %%6 ,)6 WRQ) %%6 3&$ 76 ,17 ,17 538 N 9'' &L 966 &/.287 &/.287 538 9'' DDD Ci: In case mechanical switches are used, a capacitor of 1 nF is recommended. RPU: For example, 10 k. Fig 46. General application diagram For information about application configuration, see Ref. 3 "AN11186". 16. Test information 16.1 Quality information This product has been qualified in accordance with the Automotive Electronics Council (AEC) standard Q100 - Failure mechanism based stress test qualification for integrated circuits, and is suitable for use in automotive applications. PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 69 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 17. Package outline 62SODVWLFVPDOORXWOLQHSDFNDJHOHDGVERG\ZLGWKPP ' 627 $ ( ; F +( \ Y 0 $ = 4 $ $ $ $ SLQLQGH[ /S / H GHWDLO; Z 0 ES PP VFDOH ',0(16,216 LQFKGLPHQVLRQVDUHGHULYHGIURPWKHRULJLQDOPPGLPHQVLRQV 81,7 $ PD[ $ $ $ ES F ' ( H +( / /S 4 Y Z \ PP LQFKHV = R R 1RWH 3ODVWLFRUPHWDOSURWUXVLRQVRIPP LQFK PD[LPXPSHUVLGHDUHQRWLQFOXGHG 5()(5(1&(6 287/,1( 9(56,21 ,(& -('(& 627 ( 06 -(,7$ (8523($1 352-(&7,21 ,668('$7( Fig 47. Package outline SOT162-1 (SO16) of PCA2129T PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 70 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 18. Packing information 18.1 Tape and reel information For tape and reel packing information, see Ref. 11 "SOT162-1_518" on page 76 for the PCA2129T. 19. Soldering For information about soldering, see Ref. 3 "AN11186". PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 71 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 19.1 Footprint information )RRWSULQWLQIRUPDWLRQIRUUHIORZVROGHULQJRI62SDFNDJH 627 +[ *[ 3 +\ *\ %\ $\ & ' [ ' 3 *HQHULFIRRWSULQWSDWWHUQ 5HIHUWRWKHSDFNDJHRXWOLQHGUDZLQJIRUDFWXDOOD\RXW VROGHUODQG RFFXSLHGDUHD ',0(16,216LQPP 3 3 $\ %\ & ' ' *[ *\ +[ +\ VRWBIU Fig 48. Footprint information for reflow soldering of SOT162-1 (SO16) of PCA2129T PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 72 of 84 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCA2129 Product data sheet 20. Appendix 20.1 Real-Time Clock selection Table 83. Selection of Real-Time Clocks Type name Alarm, Timer, Interrupt Interface IDD, Battery Timestamp, Watchdog output typical (nA) backup tamper input AEC-Q100 compliant Special features Packages PCF8563 X 1 I2C 250 - - - - SO8, TSSOP8, HVSON10 PCF8564A X 1 I2C 250 - - - integrated oscillator caps WLCSP 600 - - grade 1 high robustness, Tamb40 C to 125 C TSSOP8, HVSON10 X 1 PCA8565A X 1 I2C 600 - - - integrated oscillator caps, Tamb40 C to 125 C WLCSP PCF85063 - 1 I2C 220 - - - basic functions only, no alarm HXSON8 PCF85063A X 1 I2C 220 - - - tiny package SO8, DFN2626-10 PCF85063B X 1 SPI 220 - - - tiny package DFN2626-10 230 X X - time stamp, battery backup, stopwatch 1100 s SO8, TSSOP10, TSSOP8, DFN2626-10 X 2 PCF85263B X 2 SPI 230 X X - time stamp, battery backup, stopwatch 1100s TSSOP10, DFN2626-10 PCF85363A X 2 I2C 230 X X - time stamp, battery backup, stopwatch 1100s, 64 Byte RAM TSSOP10, DFN2626-10 PCF85363B X 2 SPI 230 X X - time stamp, battery backup, stopwatch 1100s, 64 Byte RAM TSSOP10, DFN2626-10 PCF8523 X 2 I2C 150 X - - lowest power 150 nA in operation, FM+ 1 MHz SO8, HVSON8, TSSOP14, WLCSP PCF2123 X 1 SPI 100 - - - lowest power 100 nA in operation TSSOP14, HVQFN16 PCF2127 X 1 I2C and SPI 500 X X - temperature SO16 compensated, quartz built in, calibrated, 512 Byte RAM PCA2129 73 of 84 (c) NXP Semiconductors N.V. 2014. All rights reserved. PCF85263A I2C Automotive accurate RTC with integrated quartz crystal Rev. 5 -- 19 December 2014 All information provided in this document is subject to legal disclaimers. PCA8565 I2C xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Selection of Real-Time Clocks ...continued Alarm, Timer, Interrupt Interface IDD, Battery Timestamp, Watchdog output typical (nA) backup tamper input AEC-Q100 compliant Special features PCF2127A X 1 I2C and SPI 500 X PCF2129 X 1 I2C and SPI 500 PCF2129A X 1 I2C and SPI PCA2129 X 1 PCA21125 X 1 Packages X - temperature SO20 compensated, quartz built in, calibrated, 512 Byte RAM X X - temperature SO16 compensated, quartz built in, calibrated 500 X X - temperature SO20 compensated, quartz built in, calibrated I2C and SPI 500 X X grade 3 temperature SO16 compensated, quartz built in, calibrated SPI 820 - - grade 1 high robustness, Tamb40 C to 125 C TSSOP14 PCA2129 74 of 84 (c) NXP Semiconductors N.V. 2014. All rights reserved. Automotive accurate RTC with integrated quartz crystal Rev. 5 -- 19 December 2014 All information provided in this document is subject to legal disclaimers. Type name NXP Semiconductors PCA2129 Product data sheet Table 83. PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 21. Abbreviations Table 84. Acronym PCA2129 Product data sheet Abbreviations Description AM Ante Meridiem BCD Binary Coded Decimal CDM Charged Device Model CMOS Complementary Metal-Oxide Semiconductor DC Direct Current GPS Global Positioning System HBM Human Body Model I2C Inter-Integrated Circuit IC Integrated Circuit LSB Least Significant Bit MCU Microcontroller Unit MM Machine Model MSB Most Significant Bit PM Post Meridiem POR Power-On Reset PORO Power-On Reset Override PPM Parts Per Million RC Resistance-Capacitance RTC Real-Time Clock SCL Serial CLock line SDA Serial DAta line SPI Serial Peripheral Interface SRAM Static Random Access Memory TCXO Temperature Compensated Xtal Oscillator Xtal crystal All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 75 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 22. References [1] AN10365 -- Surface mount reflow soldering description [2] AN10853 -- Handling precautions of ESD sensitive devices [3] AN11186 -- Application and soldering information for the PCA2129 and PCF2129 TCXO RTC [4] IEC 60134 -- Rating systems for electronic tubes and valves and analogous semiconductor devices [5] IEC 61340-5 -- Protection of electronic devices from electrostatic phenomena [6] IPC/JEDEC J-STD-020D -- Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices [7] JESD22-A114 -- Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM) [8] JESD22-C101 -- Field-Induced Charged-Device Model Test Method for Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components [9] JESD78 -- IC Latch-Up Test [10] JESD625-A -- Requirements for Handling Electrostatic-Discharge-Sensitive (ESDS) Devices [11] SOT162-1_518 -- SO16; Reel pack; SMD, 13", packing information [12] SOT163-1_518 -- SO20; Reel pack; SMD, 13", packing information [13] UM10204 -- I2C-bus specification and user manual [14] UM10569 -- Store and transport requirements [15] UM10762 -- User manual for the accurate RTC demo board OM13513 containing PCF2127T and PCF2129AT PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 76 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 23. Revision history Table 85. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA2129 v.5 20141219 Product data sheet - PCA2129T v.4 Modifications: PCA2129T v.4 * The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. * * * * * * * * * Legal texts have been adapted to the new company name where appropriate. Added Figure 3, Figure 42 and Figure 46 Enhanced Figure 7, Figure 11, Figure 19, Section 8.11.1, Figure 36, Figure 37 Added Section 9.3 Changed IDD values in Table 79 Added VOH and VOL values in Table 79 Enhanced description of internal operating voltage Added register bit allocation tables Fixed typos 20130711 Product data sheet - PCA2129T v.3 PCA2129 v.3 20130124 Product data sheet - PCA2129 v.2.1 PCA2129 v.2.1 20121114 Product data sheet - PCA2129 v.2 PCA2129 v.2 20121113 Product data sheet - PCA2129 v.1 PCA2129 v.1 20111027 Objective data sheet - - PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 77 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 24. Legal information 24.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 24.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 24.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. PCA2129 Product data sheet Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 78 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 24.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of NXP Semiconductors N.V. 25. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 79 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 26. Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Ordering information . . . . . . . . . . . . . . . . . . . . . .2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . .2 Marking codes . . . . . . . . . . . . . . . . . . . . . . . . . .2 Pin description of PCA2129 . . . . . . . . . . . . . . . .5 Register overview . . . . . . . . . . . . . . . . . . . . . . .8 Control_1 - control and status register 1 (address 00h) bit allocation . . . . . . . . . . . . . . . . . . . . . .10 Control_1 - control and status register 1 (address 00h) bit description . . . . . . . . . . . . . . . . . . . . . .10 Control_2 - control and status register 2 (address 01h) bit allocation . . . . . . . . . . . . . . . . . . . . . . 11 Control_2 - control and status register 2 (address 01h) bit description . . . . . . . . . . . . . . . . . . . . . 11 Control_3 - control and status register 3 (address 02h) bit allocation . . . . . . . . . . . . . . . . . . . . . .12 Control_3 - control and status register 3 (address 02h) bit description . . . . . . . . . . . . . . . . . . . . . .12 CLKOUT_ctl - CLKOUT control register (address 0Fh) bit allocation . . . . . . . . . . . . . . . . . . . . . .12 CLKOUT_ctl - CLKOUT control register (address 0Fh) bit description . . . . . . . . . . . . . . . . . . . . . .12 Temperature measurement period . . . . . . . . . .13 CLKOUT frequency selection . . . . . . . . . . . . . .14 Aging_offset - crystal aging offset register (address 19h) bit allocation . . . . . . . . . . . . . . .14 Aging_offset - crystal aging offset register (address 19h) bit description . . . . . . . . . . . . . .14 Frequency correction at 25 C, typical . . . . . . .15 Power management control bit description. . . .16 Output pin BBS. . . . . . . . . . . . . . . . . . . . . . . . .21 Seconds - seconds and clock integrity register (address 03h) bit allocation . . . . . . . . . . . . . . .25 Seconds - seconds and clock integrity register (address 03h) bit description . . . . . . . . . . . . . .25 Seconds coded in BCD format . . . . . . . . . . . .26 Minutes - minutes register (address 04h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Minutes - minutes register (address 04h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Hours - hours register (address 05h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Hours - hours register (address 05h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Days - days register (address 06h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Days - days register (address 06h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Weekdays - weekdays register (address 07h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Weekdays - weekdays register (address 07h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Weekday assignments . . . . . . . . . . . . . . . . . . .28 Months - months register (address 08h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Months - months register (address 08h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 PCA2129 Product data sheet Table 35. Month assignments in BCD format . . . . . . . . . 29 Table 36. Years - years register (address 09h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 37. Years - years register (address 09h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 38. Second_alarm - second alarm register (address 0Ah) bit allocation . . . . . . . . . . . . . . . . . . . . . . 33 Table 39. Second_alarm - second alarm register (address 0Ah) bit description . . . . . . . . . . . . . . . . . . . . . 33 Table 40. Minute_alarm - minute alarm register (address 0Bh) bit allocation . . . . . . . . . . . . . . . . . . . . . . 33 Table 41. Minute_alarm - minute alarm register (address 0Bh) bit description . . . . . . . . . . . . . . . . . . . . . 33 Table 42. Hour_alarm - hour alarm register (address 0Ch) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Table 43. Hour_alarm - hour alarm register (address 0Ch) bit description . . . . . . . . . . . . . . . . . . . . . . . . . 34 Table 44. Day_alarm - day alarm register (address 0Dh) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Table 45. Day_alarm - day alarm register (address 0Dh) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Table 46. Weekday_alarm - weekday alarm register (address 0Eh) bit allocation . . . . . . . . . . . . . . 35 Table 47. Weekday_alarm - weekday alarm register (address 0Eh) bit description . . . . . . . . . . . . . . 35 Table 48. Watchdg_tim_ctl - watchdog timer control register (address 10h) bit allocation . . . . . . . . . . . . . . . 36 Table 49. Watchdg_tim_ctl - watchdog timer control register (address 10h) bit description . . . . . . . . . . . . . . 36 Table 50. Watchdg_tim_val - watchdog timer value register (address 11h) bit allocation . . . . . . . . . . . . . . . 36 Table 51. Watchdg_tim_val - watchdog timer value register (address 11h) bit description . . . . . . . . . . . . . . 36 Table 52. Programmable watchdog timer . . . . . . . . . . . . 37 Table 53. Flag location in register Control_2 . . . . . . . . . . 38 Table 54. Example values in register Control_2 . . . . . . . 39 Table 55. Example to clear only AF (bit 4). . . . . . . . . . . . 39 Table 56. Example to clear only MSF (bit 7) . . . . . . . . . . 39 Table 57. Timestp_ctl - timestamp control register (address 12h) bit allocation . . . . . . . . . . . . . . . . . . . . . . 41 Table 58. Timestp_ctl - timestamp control register (address 12h) bit description. . . . . . . . . . . . . . . . . . . . . . 41 Table 59. Sec_timestp - second timestamp register (address 13h) bit allocation . . . . . . . . . . . . . . . 41 Table 60. Sec_timestp - second timestamp register (address 13h) bit description . . . . . . . . . . . . . . 41 Table 61. Min_timestp - minute timestamp register (address 14h) bit allocation . . . . . . . . . . . . . . . . . . . . . . 42 Table 62. Min_timestp - minute timestamp register (address 14h) bit description . . . . . . . . . . . . . . . . . . . . . 42 Table 63. Hour_timestp - hour timestamp register (address 15h) bit allocation . . . . . . . . . . . . . . . . . . . . . . 42 Table 64. Hour_timestp - hour timestamp register (address 15h) bit description. . . . . . . . . . . . . . . . . . . . . . 42 Table 65. Day_timestp - day timestamp register (address 16h) bit allocation . . . . . . . . . . . . . . . . . . . . . . 43 All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 80 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal Table 66. Day_timestp - day timestamp register (address 16h) bit description . . . . . . . . . . . . . . . . . . . . . .43 Table 67. Mon_timestp - month timestamp register (address 17h) bit allocation . . . . . . . . . . . . . . . . . . . . . .43 Table 68. Mon_timestp - month timestamp register (address 17h) bit description . . . . . . . . . . . . . . . . . . . . . .43 Table 69. Year_timestp - year timestamp register (address 18h) bit allocation . . . . . . . . . . . . . . . . . . . . . .43 Table 70. Year_timestp - year timestamp register (address 18h) bit description . . . . . . . . . . . . . . . . . . . . . .43 Table 71. Battery switch-over and timestamp. . . . . . . . . .44 Table 72. Effect of bits MI and SI on pin INT and bit MSF 46 Table 73. First increment of time circuits after stop release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Table 74. Interface selection input pin IFS . . . . . . . . . . . .51 Table 75. Serial interface . . . . . . . . . . . . . . . . . . . . . . . . .52 Table 76. Command byte definition . . . . . . . . . . . . . . . . .52 Table 77. I2C slave address byte . . . . . . . . . . . . . . . . . . .56 Table 78. Limiting values . . . . . . . . . . . . . . . . . . . . . . . . .58 Table 79. Static characteristics . . . . . . . . . . . . . . . . . . . .59 Table 80. Frequency characteristics . . . . . . . . . . . . . . . .64 Table 81. SPI-bus characteristics . . . . . . . . . . . . . . . . . .65 Table 82. I2C-bus characteristics . . . . . . . . . . . . . . . . . . .67 Table 83. Selection of Real-Time Clocks . . . . . . . . . . . . .73 Table 84. Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .75 Table 85. Revision history . . . . . . . . . . . . . . . . . . . . . . . .77 PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 81 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 27. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Fig 17. Fig 18. Fig 19. Fig 20. Fig 21. Fig 22. Fig 23. Fig 24. Fig 25. Fig 26. Fig 27. Fig 28. Fig 29. Fig 30. Fig 31. Fig 32. Fig 33. Fig 34. Fig 35. Fig 36. Fig 37. Fig 38. Fig 39. Fig 40. Fig 41. Fig 42. Fig 43. Block diagram of PCA2129 . . . . . . . . . . . . . . . . . .3 Pin configuration for PCA2129 (SO16) . . . . . . . . .4 Position of the stubs from the package assembly process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Handling address registers . . . . . . . . . . . . . . . . . .6 Battery switch-over behavior in standard mode with bit BIE set logic 1 (enabled) . . . . . . . . . . . . . . . . .18 Battery switch-over behavior in direct switching mode with bit BIE set logic 1 (enabled) . . . . . . . .19 Battery switch-over circuit, simplified block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Battery low detection behavior with bit BLIE set logic 1 (enabled). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Typical driving capability of VBBS: (VBBS - VDD) with respect to the output load current IBBS . . . . . . . . .22 Power failure event due to battery discharge: reset occurs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Dependency between POR and oscillator . . . . . .24 Power-On Reset (POR) system. . . . . . . . . . . . . .24 Power-On Reset Override (PORO) sequence, valid for both I2C-bus and SPI-bus. . . . . . . . . . . . . . . .25 Data flow of the time function. . . . . . . . . . . . . . . .30 Access time for read/write operations . . . . . . . . .31 Alarm function block diagram. . . . . . . . . . . . . . . .32 Alarm flag timing diagram . . . . . . . . . . . . . . . . . .35 WD_CD set logic 1: watchdog activates an interrupt when timed out . . . . . . . . . . . . . . . . . . . . . . . . . .38 Timestamp detection with two push-buttons on the TS pin (for example, for tamper detection) . . . . .39 Interrupt block diagram . . . . . . . . . . . . . . . . . . . .45 INT example for SI and MI when TI_TP is logic 146 INT example for SI and MI when TI_TP is logic 046 Example of shortening the INT pulse by clearing the MSF flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 AF timing diagram . . . . . . . . . . . . . . . . . . . . . . . .48 STOP bit functional diagram . . . . . . . . . . . . . . . .49 STOP bit release timing . . . . . . . . . . . . . . . . . . . .50 Interface selection . . . . . . . . . . . . . . . . . . . . . . . .51 SDI, SDO configurations . . . . . . . . . . . . . . . . . . .51 Data transfer overview . . . . . . . . . . . . . . . . . . . . .52 SPI-bus write example . . . . . . . . . . . . . . . . . . . . .53 SPI-bus read example . . . . . . . . . . . . . . . . . . . . .53 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Definition of START and STOP conditions. . . . . .54 System configuration . . . . . . . . . . . . . . . . . . . . . .55 Acknowledgement on the I2C-bus . . . . . . . . . . . .55 Bus protocol, writing to registers . . . . . . . . . . . . .56 Bus protocol, reading from registers . . . . . . . . . .56 Device diode protection diagram of PCA2129 . . .57 IOL on pin SDA/CE . . . . . . . . . . . . . . . . . . . . . . . .61 IDD as a function of temperature . . . . . . . . . . . . .61 IDD as a function of VDD . . . . . . . . . . . . . . . . . . . .62 Typical IDD as a function of the power management settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Typical characteristic of frequency with respect to temperature of PCA2129 . . . . . . . . . . . . . . . . . . .64 PCA2129 Product data sheet Fig 44. SPI-bus timing. . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Fig 45. I2C-bus timing diagram; rise and fall times refer to 30 % and 70 % . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Fig 46. General application diagram . . . . . . . . . . . . . . . . 69 Fig 47. Package outline SOT162-1 (SO16) of PCA2129T. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Fig 48. Footprint information for reflow soldering of SOT162-1 (SO16) of PCA2129T . . . . . . . . . . . . 72 All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 82 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 28. Contents 1 2 3 4 4.1 5 6 7 7.1 7.2 8 8.1 8.2 8.2.1 8.2.2 8.2.3 8.3 8.3.1 8.3.1.1 8.3.2 8.3.3 8.4 8.4.1 8.5 8.5.1 8.5.1.1 8.5.1.2 8.5.1.3 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 6 Register overview . . . . . . . . . . . . . . . . . . . . . . . 6 Control registers . . . . . . . . . . . . . . . . . . . . . . . 10 Register Control_1 . . . . . . . . . . . . . . . . . . . . . 10 Register Control_2 . . . . . . . . . . . . . . . . . . . . . 11 Register Control_3 . . . . . . . . . . . . . . . . . . . . . 12 Register CLKOUT_ctl . . . . . . . . . . . . . . . . . . . 12 Temperature compensated crystal oscillator . 13 Temperature measurement . . . . . . . . . . . . . . 13 OTP refresh . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Clock output . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Register Aging_offset . . . . . . . . . . . . . . . . . . . 14 Crystal aging correction . . . . . . . . . . . . . . . . . 14 Power management functions . . . . . . . . . . . . 16 Battery switch-over function . . . . . . . . . . . . . . 17 Standard mode . . . . . . . . . . . . . . . . . . . . . . . . 18 Direct switching mode . . . . . . . . . . . . . . . . . . 19 Battery switch-over disabled: only one power supply (VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . 19 8.5.1.4 Battery switch-over architecture . . . . . . . . . . . 20 8.5.2 Battery low detection function. . . . . . . . . . . . . 20 8.5.3 Battery backup supply . . . . . . . . . . . . . . . . . . 21 8.6 Oscillator stop detection function . . . . . . . . . . 22 8.7 Reset function . . . . . . . . . . . . . . . . . . . . . . . . 23 8.7.1 Power-On Reset (POR) . . . . . . . . . . . . . . . . . 23 8.7.2 Power-On Reset Override (PORO) . . . . . . . . 24 8.8 Time and date function . . . . . . . . . . . . . . . . . . 25 8.8.1 Register Seconds . . . . . . . . . . . . . . . . . . . . . . 25 8.8.2 Register Minutes. . . . . . . . . . . . . . . . . . . . . . . 26 8.8.3 Register Hours . . . . . . . . . . . . . . . . . . . . . . . . 27 8.8.4 Register Days . . . . . . . . . . . . . . . . . . . . . . . . . 27 8.8.5 Register Weekdays. . . . . . . . . . . . . . . . . . . . . 28 8.8.6 Register Months . . . . . . . . . . . . . . . . . . . . . . . 29 8.8.7 Register Years . . . . . . . . . . . . . . . . . . . . . . . . 30 8.8.8 Setting and reading the time. . . . . . . . . . . . . . 30 8.9 Alarm function. . . . . . . . . . . . . . . . . . . . . . . . . 32 8.9.1 8.9.2 8.9.3 8.9.4 8.9.5 8.9.6 8.10 8.10.1 8.10.2 8.10.3 8.10.4 Register Second_alarm . . . . . . . . . . . . . . . . . 33 Register Minute_alarm. . . . . . . . . . . . . . . . . . 33 Register Hour_alarm . . . . . . . . . . . . . . . . . . . 34 Register Day_alarm . . . . . . . . . . . . . . . . . . . . 34 Register Weekday_alarm. . . . . . . . . . . . . . . . 35 Alarm flag. . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Timer functions. . . . . . . . . . . . . . . . . . . . . . . . 35 Register Watchdg_tim_ctl . . . . . . . . . . . . . . . 36 Register Watchdg_tim_val . . . . . . . . . . . . . . . 36 Watchdog timer function . . . . . . . . . . . . . . . . 37 Pre-defined timers: second and minute interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 8.10.5 Clearing flags . . . . . . . . . . . . . . . . . . . . . . . . . 38 8.11 Timestamp function . . . . . . . . . . . . . . . . . . . . 39 8.11.1 Timestamp flag. . . . . . . . . . . . . . . . . . . . . . . . 40 8.11.2 Timestamp mode . . . . . . . . . . . . . . . . . . . . . . 40 8.11.3 Timestamp registers. . . . . . . . . . . . . . . . . . . . 41 8.11.3.1 Register Timestp_ctl . . . . . . . . . . . . . . . . . . . 41 8.11.3.2 Register Sec_timestp. . . . . . . . . . . . . . . . . . . 41 8.11.3.3 Register Min_timestp . . . . . . . . . . . . . . . . . . . 42 8.11.3.4 Register Hour_timestp . . . . . . . . . . . . . . . . . . 42 8.11.3.5 Register Day_timestp. . . . . . . . . . . . . . . . . . . 43 8.11.3.6 Register Mon_timestp . . . . . . . . . . . . . . . . . . 43 8.11.3.7 Register Year_timestp . . . . . . . . . . . . . . . . . . 43 8.11.4 Dependency between Battery switch-over and timestamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 8.12 Interrupt output, INT. . . . . . . . . . . . . . . . . . . . 44 8.12.1 Minute and second interrupts. . . . . . . . . . . . . 45 8.12.2 INT pulse shortening . . . . . . . . . . . . . . . . . . . 47 8.12.3 Watchdog timer interrupts . . . . . . . . . . . . . . . 47 8.12.4 Alarm interrupts . . . . . . . . . . . . . . . . . . . . . . . 47 8.12.5 Timestamp interrupts . . . . . . . . . . . . . . . . . . . 48 8.12.6 Battery switch-over interrupts . . . . . . . . . . . . 48 8.12.7 Battery low detection interrupts . . . . . . . . . . . 48 8.13 External clock test mode . . . . . . . . . . . . . . . . 48 8.14 STOP bit function . . . . . . . . . . . . . . . . . . . . . . 49 9 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 9.1 SPI-bus interface . . . . . . . . . . . . . . . . . . . . . . 51 9.1.1 Data transmission . . . . . . . . . . . . . . . . . . . . . 52 9.2 I2C-bus interface . . . . . . . . . . . . . . . . . . . . . . 54 9.2.1 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 9.2.2 START and STOP conditions. . . . . . . . . . . . . 54 9.2.3 System configuration . . . . . . . . . . . . . . . . . . . 54 9.2.4 Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . 55 9.2.5 I2C-bus protocol . . . . . . . . . . . . . . . . . . . . . . . 55 9.3 Bus communication and battery backup operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 10 Internal circuitry . . . . . . . . . . . . . . . . . . . . . . . 57 continued >> PCA2129 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 5 -- 19 December 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 83 of 84 PCA2129 NXP Semiconductors Automotive accurate RTC with integrated quartz crystal 11 12 13 13.1 13.2 14 14.1 14.2 15 16 16.1 17 18 18.1 19 19.1 20 20.1 21 22 23 24 24.1 24.2 24.3 24.4 25 26 27 28 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . Static characteristics. . . . . . . . . . . . . . . . . . . . Current consumption characteristics, typical . Frequency characteristics. . . . . . . . . . . . . . . . Dynamic characteristics . . . . . . . . . . . . . . . . . SPI-bus timing characteristics . . . . . . . . . . . . I2C-bus timing characteristics . . . . . . . . . . . . . Application information. . . . . . . . . . . . . . . . . . Test information . . . . . . . . . . . . . . . . . . . . . . . . Quality information . . . . . . . . . . . . . . . . . . . . . Package outline . . . . . . . . . . . . . . . . . . . . . . . . Packing information . . . . . . . . . . . . . . . . . . . . Tape and reel information . . . . . . . . . . . . . . . . Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Footprint information. . . . . . . . . . . . . . . . . . . . Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Real-Time Clock selection . . . . . . . . . . . . . . . Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . . Legal information. . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information. . . . . . . . . . . . . . . . . . . . . Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 58 59 61 64 65 65 67 69 69 69 70 71 71 71 72 73 73 75 76 77 78 78 78 78 79 79 80 82 83 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP Semiconductors N.V. 2014. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 19 December 2014 Document identifier: PCA2129 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: NXP: PCA2129T/Q900/2,51