MCP6V27 620 A, 2 MHz Auto-Zeroed Op Amps Features Description * High DC Precision: - VOS Drift: 50 nV/C (maximum) - VOS: 2 V (maximum) - AOL: 125 dB (minimum) - PSRR: 125 dB (minimum) - CMRR: 120 dB (minimum) - Eni: 1.0 VP-P (typical), f = 0.1 Hz to 10 Hz - Eni: 0.32 VP-P (typical), f = 0.01 Hz to 1 Hz * Low Power and Supply Voltages: - IQ: 620 A/amplifier (typical) - Wide Supply Voltage Range: 2.3V to 5.5V * Easy to Use: - Rail-to-Rail Input/Output - Gain Bandwidth Product: 2 MHz (typical) - Unity Gain Stable - Available in Dual * Extended Temperature Range: -40C to +125C The Microchip Technology Inc. MCP6V27 dual operational amplifier has input offset voltage correction for very low offset and offset drift. This device has a wide gain bandwidth product (2 MHz, typical) and strongly rejects switching noise. It is unity gain stable, has no 1/f noise, and has good PSRR and CMRR. This product operates with a single supply voltage as low as 2.3V, while drawing 620 A/amplifier (typical) of quiescent current. Typical Applications * * * * * Portable Instrumentation Sensor Conditioning Temperature Measurement DC Offset Correction Medical Instrumentation Design Aids * * * * * SPICE Macro Models FilterLab(R) Software Microchip Advanced Part Selector (MAPS) Analog Demonstration and Evaluation Boards Application Notes Related Parts The Microchip Technology Inc. MCP6V27 op amp is offered as a dual. It is designed in an advanced CMOS process. Package Types (top view) MCP6V27 4x4 DFN * MCP6V27 SOIC, MSOP 8 VDD VOUTA 1 VOUTA 7 VOUTB V - INA 6 VINB- V + INA 5 VINB+ V SS VINA- 2 VINA+ 3 VSS 4 8 VDD 1 2 3 EP 9 7 VOUTB 6 VINB- 5 VINB+ 4 * Includes Exposed Thermal Pad (EP); see Table 3-1. Typical Application Circuit 10 k 10 k VOUT VIN 10 k 10 nF 500 k MCP661 10 k 5 k VDD/2 1/2 MCP6V27 VDD/2 Offset Voltage Correction for Power Driver Parts with lower power, lower bandwidth and higher noise: * MCP6V01/2/3: Spread clock * MCP6V06/7/8: Non-spread clock (c) 2011 Microchip Technology Inc. DS25007A-page 1 MCP6V27 NOTES: DS25007A-page 2 (c) 2011 Microchip Technology Inc. MCP6V27 1.0 ELECTRICAL CHARACTERISTICS 1.1 Absolute Maximum Ratings Notice: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. See Section 4.2.1, Rail-to-Rail Inputs. VDD - VSS ..............................................................................6.5V Current at Input Pins ......................................................2 mA Analog Inputs (VIN+ and VIN-) .......... VSS - 1.0V to VDD+1.0V All other Inputs and Outputs .................. VSS - 0.3V to VDD+0.3V Difference Input voltage ............................................. |VDD - VSS| Output Short Circuit Current ....................................... Continuous Current at Output and Supply Pins ...................................30 mA Storage Temperature ..........................................-65C to +150C Max. Junction Temperature .............................................. +150C ESD protection on all pins (HBM, CDM, MM) 4 kV,1.5 kV, 300V 1.2 Specifications TABLE 1-1: DC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = +25C, VDD = +2.3V to +5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2 and RL = 10 k to VL (refer to Figure 1-4 and Figure 1-5). Parameters Sym Min Typ Max Units Conditions Input Offset Voltage VOS -2 -- +2 V Input Offset Voltage Drift with Temperature (linear Temp. Co.) TC1 -50 -- +50 nV/C TA = -40 to +125C (Note 1) Input Offset Voltage Quadratic Temperature Coefficient TC2 -- 0.2 -- nV/C2 TA = -40 to +125C PSRR 125 142 -- dB Input Bias Current IB -- +7 -- pA Input Bias Current across Temperature IB -- +110 -- pA TA = +85C IB -- +1.2 +5 nA TA = +125C Input Offset Current IOS -- 70 -- pA Input Offset Current across Temperature IOS -- 50 -- pA TA = +85C IOS -- 60 -- pA TA = +125C -- ||pF -- ||pF Input Offset Power Supply Rejection TA = +25C (Note 1) (Note 1) Input Bias Current and Impedance Common Mode Input Impedance ZCM -- 1013||12 Differential Input Impedance ZDIFF -- 1013||12 Note 1: 2: Set by design and characterization. Due to thermal junction and other effects in the production environment, these parts can only be screened in production (except TC1; see Appendix B: "Offset Related Test Screens"). Figure 2-18 shows how VCML and VCMH changed across temperature for the first production lot. (c) 2011 Microchip Technology Inc. DS25007A-page 3 MCP6V27 TABLE 1-1: DC ELECTRICAL SPECIFICATIONS (CONTINUED) Electrical Characteristics: Unless otherwise indicated, TA = +25C, VDD = +2.3V to +5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2 and RL = 10 k to VL (refer to Figure 1-4 and Figure 1-5). Parameters Sym Min Typ Max Units Conditions Common-Mode Input Voltage Range Low VCML -- -- VSS - 0.15 V (Note 2) Common-Mode Input Voltage Range High VCMH VDD + 0.2 -- -- V (Note 2) Common-Mode Rejection CMRR 120 136 -- dB VDD = 2.3V, VCM = -0.15V to 2.5V (Note 1, Note 2) CMRR 125 142 -- dB VDD = 5.5V, VCM = -0.15V to 5.7V (Note 1, Note 2) AOL 125 147 -- dB VDD = 2.3V, VOUT = 0.2V to 2.1V (Note 1) AOL 133 155 -- dB VDD = 5.5V, VOUT = 0.2V to 5.3V (Note 1) Minimum Output Voltage Swing VOL -- VSS + 5 VSS + 15 mV G = +2, 0.5V input overdrive Maximum Output Voltage Swing VOH -- mV G = +2, 0.5V input overdrive Output Short Circuit Current ISC -- 12 -- mA VDD = 2.3V ISC -- 22 -- mA VDD = 5.5V Common Mode Open-Loop Gain DC Open-Loop Gain (large signal) Output VDD - 15 VDD - 5 Power Supply Supply Voltage Quiescent Current per amplifier POR Trip Voltage Note 1: 2: VDD 2.3 -- 5.5 V IQ 450 620 800 A VPOR 1.15 -- 1.65 V IO = 0 Set by design and characterization. Due to thermal junction and other effects in the production environment, these parts can only be screened in production (except TC1; see Appendix B: "Offset Related Test Screens"). Figure 2-18 shows how VCML and VCMH changed across temperature for the first production lot. DS25007A-page 4 (c) 2011 Microchip Technology Inc. MCP6V27 TABLE 1-2: AC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = +25C, VDD = +2.3V to +5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF (refer to Figure 1-4 and Figure 1-5). Parameters Sym Min Typ Max Units Conditions GBWP -- 2.0 -- MHz Slew Rate SR -- 1.0 -- V/s Phase Margin PM -- 65 -- Eni -- 0.32 -- VP-P f = 0.01 Hz to 1 Hz Eni -- 1.0 -- VP-P f = 0.1 Hz to 10 Hz eni -- 50 -- nV/Hz f < 5 kHz eni -- 29 -- nV/Hz f = 100 kHz ini -- 0.6 -- fA/Hz IMD -- 40 -- VPK Start Up Time tSTR -- 75 -- s G = +1, VOS within 50 V of its final value (Note 2) Offset Correction Settling Time tSTL -- 150 -- s G = +1, VIN step of 2V, VOS within 50 V of its final value Output Overdrive Recovery Time tODR -- 45 -- s G = -100, 0.5V input overdrive to VDD/2, VIN 50% point to VOUT 90% point (Note 3) Amplifier AC Response Gain Bandwidth Product G = +1 Amplifier Noise Response Input Noise Voltage Input Noise Voltage Density Input Noise Current Density Amplifier Distortion (Note 1) Intermodulation Distortion (AC) VCM tone = 50 mVPK at 1 kHz, GN = 1 Amplifier Step Response Note 1: 2: 3: These parameters were characterized using the circuit in Figure 1-6. In Figure 2-37 and Figure 2-38, there is an IMD tone at DC, a residual tone at 1 kHz, other IMD tones and clock tones. High gains behave differently; see Section 4.3.3, Offset at Power Up. tODR includes some uncertainty due to clock edge timing. TABLE 1-3: TEMPERATURE SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, all limits are specified for: VDD = +2.3V to +5.5V, VSS = GND. Parameters Sym Min Typ Max Units Specified Temperature Range TA -40 -- +125 C Operating Temperature Range TA -40 -- +125 C Storage Temperature Range TA -65 -- +150 C Thermal Resistance, 8L-4x4 DFN JA -- 48 -- C/W Thermal Resistance, 8L-MSOP JA -- 211 -- C/W Thermal Resistance, 8L-SOIC JA -- 150 -- C/W Conditions Temperature Ranges (Note 1) Thermal Package Resistances Note 1: 2: (Note 2) Operation must not cause TJ to exceed Maximum Junction Temperature specification (+150C). Measured on a standard JC51-7, four layer printed circuit board with ground plane and vias. (c) 2011 Microchip Technology Inc. DS25007A-page 5 MCP6V27 1.3 Timing Diagrams 1.4 2.3V to 5.5V 2.3V VDD 0V tSTR VOS + 50 V VOS Test Circuits The circuits used for the DC and AC tests are shown in Figure 1-4 and Figure 1-5. Lay the bypass capacitors out as discussed in Section 4.3.10, Supply Bypassing and Filtering. RN is equal to the parallel combination of RF and RG to minimize bias current effects. VDD VOS - 50 V VIN FIGURE 1-1: Amplifier Start Up. RISO tSTL 100 nF RG VOS + 50 V VOS VOS + 50 V Offset Correction Settling CL RL VL RF FIGURE 1-4: AC and DC Test Circuit for Most Non-Inverting Gain Conditions. VDD FIGURE 1-2: Time. VOUT 1/2 MCP6V27 VDD/3 VIN 1 F RN 1 F VDD/3 RN RISO VOUT 1/2 MCP6V27 VIN 100 nF VIN tODR RG VDD tODR VOUT VDD/2 VSS FIGURE 1-3: Output Overdrive Recovery. CL RL VL RF FIGURE 1-5: AC and DC Test Circuit for Most Inverting Gain Conditions. The circuit in Figure 1-6 tests the op amp input's dynamic behavior (i.e., IMD, tSTR, tSTL and tODR). The potentiometer balances the resistor network (VOUT should equal VREF at DC). The op amp's common mode input voltage is VCM = VIN/2. The error at the input (VERR) appears at VOUT with a noise gain of 10 V/V. VIN 2.49 k 2.49 k 20.0 k 20.0 k 50 0.1% 0.1% 25 turn VDD VREF 1 F RISO 100 nF 1/2 MCP6V27 VOUT CL RL VL 20.0 k 20.0 k 24.9 0.1% 0.1% FIGURE 1-6: Input Behavior. DS25007A-page 6 Test Circuit for Dynamic (c) 2011 Microchip Technology Inc. MCP6V27 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF. 2.1 DC Input Precision Percentage of Occurrences 40% 35% 30% 20 Samples TA = +25C VDD = 2.3V and 5.5V 25% 20% 15% 10% 5% 2.0 1.0 0.0 -1.0 -2.0 0% Input Offset Voltage (V) FIGURE 2-1: Percentage of Occurrences 30% 25% Input Offset Voltage. FIGURE 2-4: Input Offset Voltage vs. Power Supply Voltage with VCM = VCML. 20 Samples VDD = 2.3V and 5.5V 20% 15% 10% 5% 50 40 30 20 10 0 -10 -20 -30 -40 -50 0% Input Offset Voltage Drift; TC1 (nV/C) Input Offset Voltage Drift. FIGURE 2-5: Input Offset Voltage vs. Power Supply Voltage with VCM = VCMH. Input Offset Voltage (V) FIGURE 2-2: 5 4 3 2 1 0 -1 -2 -3 -4 -5 Representative Part VDD = 2.3V VDD = 5.5V 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Output Voltage (V) FIGURE 2-3: Input Offset Voltage Quadratic Temperature Coefficient. (c) 2011 Microchip Technology Inc. FIGURE 2-6: Output Voltage. Input Offset Voltage vs. DS25007A-page 7 MCP6V27 Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF. 30% FIGURE 2-10: 0.4 0.3 0.2 0.1 0.0 0.4 0.3 0.2 0.1 0.0 155 25% VDD = 5.5V 15% DC Open-Loop Gain. 160 CMRR, PSRR (dB) Percentage of Occurrences FIGURE 2-11: 20 Samples TA = +25C 20% -0.1 1/AOL (V/V) FIGURE 2-8: Input Offset Voltage vs. Common Mode Voltage with VDD = 5.5V. 30% VDD = 5.5V VDD = 2.3V -0.2 Percentage of Occurrences 20 Samples TA = +25C 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% PSRR. Input Common Mode Voltage (V) 35% -0.1 1/PSRR (V/V) -40C +25C +85C +125C 2.0 1.5 1.0 0.5 0.0 -0.5 Input Offset Voltage (V) VDD = 5.5V Representative Part 0% 3.0 FIGURE 2-7: Input Offset Voltage vs. Common Mode Voltage with VDD = 2.3V. 5 4 3 2 1 0 -1 -2 -3 -4 -5 5% -0.2 0.5 1.0 1.5 2.0 2.5 Input Common Mode Voltage (V) 10% -0.3 0.0 15% -0.4 -4 -5 -0.5 20% -0.4 -40C +25C +85C +125C 20 Samples TA = +25C 25% -0.3 VDD = 2.3V Representative Part 4 3 2 1 0 -1 -2 -3 Percentage of Occurrences Input Offset Voltage (V) 5 VDD = 2.3V 10% 5% PSRR 150 145 140 135 130 VDD = 5.5V VDD = 2.3V CMRR 125 1/CMRR (V/V) FIGURE 2-9: DS25007A-page 8 CMRR. 0.5 0.3 0.0 -0.3 -0.5 0% 120 -50 -25 0 25 50 75 100 Ambient Temperature (C) 125 FIGURE 2-12: CMRR and PSRR vs. Ambient Temperature. (c) 2011 Microchip Technology Inc. MCP6V27 Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF. 10n 10,000 Input Bias, Offset Currents (A) DC Open-Loop Gain (dB) 160 155 150 1n 1,000 VDD = 5.5V VDD = 2.3V 145 140 135 130 125 120 -50 -25 0 25 50 75 100 Ambient Temperature (C) 1p 1 25 35 45 55 65 75 85 95 105 115 125 Ambient Temperature (C) Input Current Magnitude (A) 1.E-04 100 1.E-05 10 100 IB 50 1.E-06 1 1.E-07 100n 0 1.E-08 10n IOS -50 1.E-09 1n 1.E-10 100p 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.0 0.5 -100 -0.5 Input Bias, Offset Currents (pA) IB 1.E-02 10m 1.E-03 1m Common Mode Input Voltage (V) FIGURE 2-14: Input Bias and Offset Currents vs. Common Mode Input Voltage with TA = +85C. +125C +85C +25C -40C 10p 1.E-11 -1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 Input Voltage (V) FIGURE 2-17: Input Bias Current vs. Input Voltage (below VSS). TA = +125C VDD = 5.5V IB 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 IOS 0.0 2000 1800 1600 1400 1200 1000 800 600 400 200 0 -200 -400 -0.5 Input Bias, Offset Currents (pA) 10p 10 FIGURE 2-16: Input Bias and Offset Currents vs. Ambient Temperature with VDD = +5.5V. TA = +85C VDD = 5.5V 150 -IOS 100p 100 125 FIGURE 2-13: DC Open-Loop Gain vs. Ambient Temperature. 200 VDD = 5.5V Common Mode Input Voltage (V) FIGURE 2-15: Input Bias and Offset Currents vs. Common Mode Input Voltage with TA = +125C. (c) 2011 Microchip Technology Inc. DS25007A-page 9 MCP6V27 Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF. Other DC Voltages and Currents -25 0 25 50 75 100 Ambient Temperature (C) 125 FIGURE 2-20: Output Voltage Headroom vs. Ambient Temperature. DS25007A-page 10 6.0 5.5 5.0 6.5 6.5 6.0 5.5 5.0 4.5 4.0 15% 10% 5% 0% 1.35 -50 20% 1.34 0 25% 1.33 VDD = 2.3V 30% 820 Samples 1 Wafer Lot TA = +25C 1.32 VOL - VSS 35% Supply Current vs. Power 1.31 1 FIGURE 2-22: Supply Voltage. 1.30 VDD - VOH 3 2 0 1.25 VDD = 5.5V 4 100 Power Supply Voltage (V) Percentage of Occurrences Output Headroom (mV) 7 5 200 40% RL = 10 k 8 6 +125C +85C +25C -40C 300 3.5 10 FIGURE 2-19: Output Voltage Headroom vs. Output Current. 400 0.0 10 500 3.0 VOL - VSS 600 1.29 VDD - VOH 700 2.5 100 800 2.0 Supply Current (A/amplifier) Output Voltage Headroom (mV) VDD = 5.5V VDD = 2.3V 10 9 4.5 FIGURE 2-21: Output Short Circuit Current vs. Power Supply Voltage. 1000 1 Output Current Magnitude (mA) 4.0 Power Supply Voltage (V) FIGURE 2-18: Input Common Mode Voltage Headroom (Range) vs. Ambient Temperature. 0.1 -40 125 1.28 0 25 50 75 100 Ambient Temperature (C) 1.5 -25 1.27 -50 +125C +85C +25C -40C -30 0.0 -0.4 -20 3.5 Lower (VCML - VSS) -0.3 1.0 -0.2 0 -10 3.0 -0.1 10 2.5 0.0 20 2.0 0.1 1.5 0.2 -40C +25C +85C +125C 30 1.0 Upper ( VCMH - VDD) 1.26 0.3 40 0.5 1 Wafer Lot 0.5 Input Common Mode Voltage Headroom (V) 0.4 Output Short Circuit Current (mA) 2.2 POR Trip Voltage (V) FIGURE 2-23: Voltage. Power On Reset Trip (c) 2011 Microchip Technology Inc. MCP6V27 Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF. 1.8 POR Trip Voltage (V) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -50 -25 0 25 50 75 100 Ambient Temperature (C) 125 FIGURE 2-24: Power On Reset Voltage vs. Ambient Temperature. (c) 2011 Microchip Technology Inc. DS25007A-page 11 MCP6V27 Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF. PSRR+ PSRR- CMRR and PSRR vs. -10 -240 -270 10M 1.E+07 Open-Loop Gain (dB) 0 -30 50 -60 40 -90 AOL 30 20 -180 | AOL | 0 -210 -10 -20 1k 1.E+03 -120 -150 10 -240 10k 100k 1M 1.E+04 1.E+05 1.E+06 Frequency (Hz) -270 10M 1.E+07 FIGURE 2-27: Open-Loop Gain vs. Frequency with VDD = 5.5V. DS25007A-page 12 3.0 100 VDD = 5.5V GBWP VDD = 2.3V 2.5 90 20 2.0 80 1.5 70 1.0 60 Ph hase Margin () 120 110 PM 0.5 50 0.0 40 FIGURE 2-29: Gain Bandwidth Product and Phase Margin vs. Common Mode Input Voltage. Open-Loop Phase () VDD = 5.5V CL = 60 pF 60 4.0 Common Mode Input Voltage (V) FIGURE 2-26: Open-Loop Gain vs. Frequency with VDD = 2.3V. 70 125 4.0 120 3.5 110 3.0 2.5 100 VDD = 2.3V PM VDD = 5.5V 90 20 2.0 80 1.5 70 1.0 GBWP 0.5 60 Ph hase Ma argin () 10k 100k 1M 1.E+04 1.E+05 1.E+06 Frequency (Hz) 0 25 50 75 100 Ambient Temperature (C) 3.5 -0 0.5 -20 1k 1.E+03 -25 25 6.0 6 -210 40 50 -50 5.5 5 0 0.0 5.0 5 -180 | AOL | 50 4.5 4 10 0.5 4.0 4 -150 60 3.5 3 -120 20 PM 1.0 3.0 3 30 70 VDD = 2.3V 2.5 2 -30 -90 15 1.5 FIGURE 2-28: Gain Bandwidth Product and Phase Margin vs. Ambient Temperature. 0 -60 AOL 40 80 2.0 2 50 2.0 1.5 60 90 VDD = 5.5V GBWP 1.0 VDD = 2.3V CL = 60 pF 2.5 0.5 0 70 Open-Loop Gain (dB) 1M 1.E+06 100 0.0 0 FIGURE 2-25: Frequency. 10k 100k 1.E+04 1.E+05 Frequency (Hz) ain Ban ndwidth h Produ uct (MH Hz) Ga 1k 1.E+03 3.0 Ph hase Ma argin () CMRR Gaiin Band dwidth Produ uct (MH Hz) 110 100 90 80 70 60 50 40 30 20 10 0 100 1.E+02 Gain Band dwidth Produ uct (MH Hz) Frequency Response Open-Loop Phase () CMRR, PSRR (dB) 2.3 50 0.0 40 0 0 0.5 0.0 0 5 1.0 10 1 1.5 5 2.0 2 0 2.5 2 5 3.0 3 0 3.5 3 5 4.0 4 0 4.5 4 5 5.0 5 0 5.5 55 Output Voltage (V) FIGURE 2-30: Gain Bandwidth Product and Phase Margin vs. Output Voltage. (c) 2011 Microchip Technology Inc. MCP6V27 Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF. VDD = 2.3V Closed-Loop Output Impedance () 1.E+04 10k 1.E+03 1k 1.E+02 100 10 1.E+01 1.E+001 100k 1.0E+05 G = 1 V/V G = 11 V/V G = 101 V/V 1M 10M 1.0E+06 1.0E+07 Frequency (Hz) 100M 1.0E+08 FIGURE 2-31: Closed-Loop Output Impedance vs. Frequency with VDD = 2.3V. 10 Maximum Output Voltage Swing (VP-P) VDD = 5.5V Closed-Loop Output Impedance () 1.E+04 10k 1.E+03 1k 1.E+02 100 10 1.E+01 1.E+001 100k 1.0E+05 FIGURE 2-33: Channel-to-Channel Separation vs. Frequency. G = 1 V/V G = 10 V/V G = 100 V/V 1M 10M 1.0E+06 1.0E+07 Frequency (Hz) 100M 1.0E+08 FIGURE 2-32: Closed-Loop Output Impedance vs. Frequency with VDD = 5.5V. (c) 2011 Microchip Technology Inc. VDD = 5.5V VDD = 2.3V 1 0.1 1k 1.E+03 10k 100k 1.E+04 1.E+05 Frequency (Hz) 1M 1.E+06 FIGURE 2-34: Maximum Output Voltage Swing vs. Frequency. DS25007A-page 13 MCP6V27 Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF. Input Noise and Distortion VDD = 5.5V VDD = 2.3V 1,000 100 100 1,000 100 eni 10 Eni(0 Hz to f) 10 1 100 100k 110E 01 1 1.E+01 1.E+02 E 02 1.E+03 1 1k E 03 1.E+04 1 10k E 04 1 1.E+05 E 05 Frequency (Hz) 100 90 80 70 60 50 40 30 20 10 0 1 kHz tone VDD = 5.5V VDD = 2.3V 10 1 GDM = 1 V/V VDD tone = 50 mVP-P, f = 1 kHz 0.1 100 1.E+02 1k 10k 1.E+03 1.E+04 Frequency (Hz) VDD = 2.3V Input Noise Voltage; eni(t) (0.2 V/div) VDD = 5.5V VDD = 2.3V NPBW = 10 Hz 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 NPBW = 1 Hz 0 10 20 30 40 Common Mode Input Voltage (V) FIGURE 2-36: Input Noise Voltage Density vs. Input Common Mode Voltage. 50 60 t (s) 70 80 90 100 FIGURE 2-39: Input Noise vs. Time with 1 Hz and 10 Hz Filters and VDD =2.3V. 100 VDD = 5.5V IMD tone at DC Input Noise Voltage; eni(t) (0.2 V/div) IMD Spectrum, RTI (V PK) 100k 1.E+05 FIGURE 2-38: Inter-Modulation Distortion vs. Frequency with VDD Disturbance (see Figure 1-6). f < 5 kHz -0.5 Input Noise Voltage Density (nV/Hz) FIGURE 2-35: Input Noise Voltage Density and Integrated Input Noise Voltage vs. Frequency. IMD tone at DC IMD Spectrum, RTI (VPK) Inp put Noise Volltage D Density;; eni (nV//Hz) 10,000 Integrrated In nput No oise Vo oltage; Eni (VP-P) 2.4 residual 1 kHz tone 10 VDD = 2.3V VDD = 5.5V 1 GDM = 1 V/V VCM tone = 50 mVPK, f = 1 kHz 0.1 100 1.E+02 1k 10k 1.E+03 1.E+04 Frequency (Hz) NPBW = 1 Hz 100k 1.E+05 FIGURE 2-37: Inter-Modulation Distortion vs. Frequency with VCM Disturbance (see Figure 1-6). DS25007A-page 14 NPBW = 10 Hz 0 10 20 30 40 50 60 t (s) 70 80 90 100 FIGURE 2-40: Input Noise vs. Time with 1 Hz and 10 Hz Filters and VDD =5.5V. (c) 2011 Microchip Technology Inc. MCP6V27 Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 k to VL and CL = 60 pF. Time Response 2 0 -2 90 80 70 60 VOS -4 -6 -8 -10 100 50 40 30 20 TPCB -12 10 -14 0 20 40 60 0 80 100 120 140 160 180 Time (s) 0 FIGURE 2-41: Input Offset Voltage vs. Time with Temperature Change. 6 G=1 80 5 VDD 70 4 60 3 50 2 40 1 POR Trip Point 30 0 20 -1 10 -2 VOS 0 -3 -10 -4 5 10 VOUT 3 2 1 0 5 6 Time (s) 7 8 9 10 15 20 25 30 Time (s) 35 40 45 50 Non-inverting Large Signal VDD = 5.5V G = -1 Output Voltage (10 mV/div) Input, Output Voltages (V) 5 4 4 Non-inverting Small Signal FIGURE 2-45: Step Response. VDD = 5.5V G=1 VIN 3 VDD = 5.5V G=1 0 FIGURE 2-42: Input Offset Voltage vs. Time at Power Up. 6 2 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Time (ms) 7 1 FIGURE 2-44: Step Response. Power Supply Voltage (V) Input Offset Voltage (V) 90 VDD = 5.5V G=1 Output Voltage (10 mV/div) Temperature increased by using heat gun for 10 seconds. 4 Output Voltage (V) Input Offset Voltage (V) 6 PCB Temperature (C) 2.5 -1 0 1 2 3 4 5 6 Time (ms) 7 8 9 10 FIGURE 2-43: The MCP6V27 Device Shows No Input Phase Reversal with Overdrive. (c) 2011 Microchip Technology Inc. 0 1 2 FIGURE 2-46: Response. 3 4 5 6 Time (s) 7 8 9 10 Inverting Small Signal Step DS25007A-page 15 MCP6V27 Note: Unless otherwise indicated, TA = +25C, VDD = +2.3V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, 6.0 VDD = 5.5V G = -1 5.0 5 G VIN VOUT 4.0 4 3.0 3 2.0 VDD = 5.5V G = -100 V/V 0.5V Overdrive 1.0 VOUT 2 G VIN 0.0 0 5 10 15 FIGURE 2-47: Response. 20 25 30 Time (s) 35 40 45 Inverting Large Signal Step 1.4 Falling Edge 1.2 1.0 0.8 0.6 Rising Edge VDD = 2.3V 0.4 0.2 0.0 -50 -25 FIGURE 2-48: Temperature. DS25007A-page 16 0 25 50 75 100 Ambient Temperature (C) Slew Rate vs. Ambient 125 Time (50 s/div) -1 FIGURE 2-49: Output Overdrive Recovery vs. Time with G = -100 V/V. Overdrive Recovery Time (s) VDD = 5.5V 1 0 -1.0 50 1.6 Slew Rate (V/s) 6 Input Voltage x G (V/V) 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 Output Voltage (V) Output Voltage (V) VL = VDD/2, RL = 10 k to VL and CL = 60 pF. 1000 0.5V Output Overdrive 100 VDD = 5.5V t ODR, high 10 tODR, low VDD = 2.3V 1 1 10 100 Inverting Gain Magnitude (V/V) 1000 FIGURE 2-50: Output Overdrive Recovery Time vs. Inverting Gain. (c) 2011 Microchip Technology Inc. MCP6V27 3.0 PIN DESCRIPTIONS Descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE MCP6V27 3.1 Symbol MSOP, SOIC 1 1 VOUT, VOUTA Output (op amp A) 2 2 VIN-, VINA- Inverting Input (op amp A) 3 3 VIN+, VINA+ Non-inverting Input (op amp A) 4 4 VSS 5 5 VINB+ Non-inverting Input (op amp B) 6 6 VINB- Inverting Input (op amp B) 7 7 VOUTB Output (op amp B) 8 8 VDD Positive Power Supply 9 -- EP Exposed Thermal Pad (EP); must be connected to VSS Analog Outputs The analog output pins (VOUT) are low-impedance voltage sources. 3.2 Analog Inputs The non-inverting and inverting inputs (VIN+, VIN-, ...) are high-impedance CMOS inputs with low bias currents. 3.3 Description DFN Negative Power Supply 3.4 Exposed Thermal Pad (EP) There is an internal connection between the Exposed Thermal Pad (EP) and the VSS pin; they must be connected to the same potential on the Printed Circuit Board (PCB). This pad can be connected to a PCB ground plane to provide a larger heat sink. This improves the package thermal resistance (JA). Power Supply Pins The positive power supply (VDD) is 2.3V to 5.5V higher than the negative power supply (VSS). For normal operation, the other pins are between VSS and VDD. Typically, these parts are used in a single (positive) supply configuration. In this case, VSS is connected to ground and VDD is connected to the supply. VDD will need bypass capacitors. (c) 2011 Microchip Technology Inc. DS25007A-page 17 MCP6V27 NOTES: DS25007A-page 18 (c) 2011 Microchip Technology Inc. MCP6V27 4.0 APPLICATIONS 4.1 The MCP6V27 auto-zeroed op amp is manufactured using Microchip's state of the art CMOS process. It is designed for low cost, low power and high precision applications. Its low supply voltage, low quiescent current and wide bandwidth makes the MCP6V27 device ideal for battery-powered applications. Overview of Auto-Zeroing Operation Figure 4-1 shows a simplified diagram of the MCP6V27 auto-zeroed op amp. This will be used to explain how the DC voltage errors are reduced in this architecture. VIN+ VIN- Main Amp. CFW NC Output Buffer VOUT VREF Null Input Switches 1 Null Output Switches Null Amp. CH POR Null Correct Switches 2 FIGURE 4-1: 4.1.1 1 2 Digital Control Oscillator Simplified Auto-Zeroed Op Amp Functional Diagram. BUILDING BLOCKS The Null Amplifier and Main Amplifier are designed for high gain and accuracy using a differential topology. They have a main input pair (+ and - pins at their top left) used for the signal. They have an auxiliary input pair (+ and - pins at their bottom left) used for correcting the offset voltages. Both input pairs are added together internally. The capacitors at the auxiliary inputs (CFW and CH) hold the corrected values during normal operation. The Output Buffer is designed to drive external loads at the VOUT pin. It also produces a single ended output voltage (VREF is an internal reference voltage). (c) 2011 Microchip Technology Inc. All of these switches are make-before-break in order to minimize glitch-induced errors. They are driven by two clock phases (1 and 2) that select between normal mode and auto-zeroing mode. The clock is derived from an internal R-C oscillator running at a rate of fOSC1 = 850 kHz. The oscillator's output is divided down to the desired rate. The internal POR ensures the part starts up in a known good state. It also provides protection against power supply brown-out events. The Digital Control circuitry takes care of all of the housekeeping details of the switching operation. It also takes care of POR events. DS25007A-page 19 MCP6V27 4.1.2 AUTO-ZEROING ACTION Figure 4-2 shows the connections between amplifiers during the Normal Mode of operation (1). The hold capacitor (CH) corrects the Null Amplifier's input offset. Since the Null Amplifier has very high gain, it dominates the signal seen by the Main Amplifier. This greatly reduces the impact of the Main Amplifier's input offset voltage on overall performance. Essentially, the Null Amplifier and Main Amplifier behave as a regular op amp with very high gain (AOL) and very low offset voltage (VOS). VIN+ VIN- CFW CH Main Amp. NC Output Buffer VOUT VREF Null Amp. Normal Mode of Operation (1); Equivalent Amplifier Diagram. FIGURE 4-2: Figure 4-3 shows the connections between amplifiers during the Auto-zeroing Mode of operation (2). The signal goes directly through the Main Amplifier, and the flywheel capacitor (CFW) maintains a constant correction on the Main Amplifier's offset. Since these corrections happen every 40 s, or so, we also minimize slow errors, including offset drift with temperature (VOS/TA), 1/f noise, and input offset aging. The Null Amplifier uses its own high open loop gain to drive the voltage across CH to the point where its input offset voltage is almost zero. Because the signal input pair is connected to VIN+, the auto-zeroing action corrects the offset at the current common mode input voltage (VCM) and supply voltage (VDD). This makes the DC CMRR and PSRR very high also. VIN+ VIN- CFW CH FIGURE 4-3: 4.1.3 Null Amp. Main Amp. NC Output Buffer VOUT VREF Auto-zeroing Mode of Operation (2); Equivalent Diagram. INTERMODULATION DISTORTION (IMD) The MCP6V27 op amp will show intermodulation distortion (IMD), products when an AC signal is present. frequencies. IMD distortion tones are generated about all of the square wave clock's harmonics. See Figure 2-37 and Figure 2-38. The signal and clock can be decomposed into sine wave tones (Fourier series components). These tones interact with the auto-zeroing circuitry's non-linear response to produce IMD tones at sum and difference DS25007A-page 20 (c) 2011 Microchip Technology Inc. MCP6V27 4.2 Other Functional Blocks 4.2.1 RAIL-TO-RAIL INPUTS The input stage of the MCP6V27 op amp uses two differential CMOS input stages in parallel. One operates at low common mode input voltage (VCM, which is approximately equal to VIN+ and VIN- in normal operation) and the other at high VCM. With this topology, the input operates with VCM up to VDD + 0.2V, and down to VSS - 0.15V, at +25C (see Figure 2-18). The input offset voltage (VOS) is measured at VCM = VSS - 0.15V and VDD + 0.2V to ensure proper operation. The transition between the input stages occurs when VCM VDD - 1.2V (see Figure 2-7 and Figure 2-8). For the best distortion and gain linearity, with non-inverting gains, avoid this region of operation. 4.2.1.1 The input ESD diodes clamp the inputs when they try to go more than one diode drop below VSS. They also clamp any voltages that are well above VDD; their breakdown voltage is high enough to allow normal operation, but not low enough to protect against slow over-voltage (beyond VDD) events. Very fast ESD events (that meet the spec) are limited so that damage does not occur. In some applications, it may be necessary to prevent excessive voltages from reaching the op amp inputs; Figure 4-5 shows one approach to protecting these inputs. D1 and D2 may be small signal silicon diodes, Schottky diodes for lower clamping voltages or diodeconnected FETs for low leakage. VDD Phase Reversal The input devices are designed to not exhibit phase inversion when the input pins exceed the supply voltages. Figure 2-43 shows an input voltage exceeding both supplies with no phase inversion. 4.2.1.2 U1 D1 Input Voltage Limits In order to prevent damage and/or improper operation of these amplifiers, the circuit must limit the voltages at the input pins (see Section 1.1, Absolute Maximum Ratings ). This requirement is independent of the current limits discussed later on. The ESD protection on the inputs can be depicted as shown in Figure 4-4. This structure was chosen to protect the input transistors against many (but not all) over-voltage conditions, and to minimize input bias current (IB). VDD Bond Pad 1/2 MCP6V27 V1 D2 VOUT V2 FIGURE 4-5: Protecting the Analog Inputs Against High Voltages. 4.2.1.3 Input Current Limits In order to prevent damage and/or improper operation of these amplifiers, the circuit must limit the currents into the input pins (see Section 1.1, Absolute Maximum Ratings ). This requirement is independent of the voltage limits previously discussed. Figure 4-6 shows one approach to protecting these inputs. The resistors R1 and R2 limit the possible current in or out of the input pins (and into D1 and D2). The diode currents will dump onto VDD. VDD VIN+ Bond Pad Input Stage Bond V - IN Pad V1 V2 VSS Bond Pad FIGURE 4-4: Structures. Simplified Analog Input ESD U1 D1 R1 1/2 MCP6V27 D2 VOUT R2 VSS - min(V1, V2) 2 mA max(V1, V2) - VDD min(R1, R2) > 2 mA min(R1, R2) > FIGURE 4-6: Protecting the Analog Inputs Against High Currents. (c) 2011 Microchip Technology Inc. DS25007A-page 21 MCP6V27 It is also possible to connect the diodes to the left of resistors R1 and R2. In this case, the currents through the diodes D1 and D2 need to be limited by some other mechanism. The resistors then serve as in-rush current limiters; the DC current into the input pins (VIN+ and VIN-) should be very small. A significant amount of current can flow out of the inputs (through the ESD diodes) when the common mode voltage (VCM) is below ground (VSS); see Figure 2-17. 4.2.2 RAIL-TO-RAIL OUTPUT This op amp is designed to drive light loads; use another amplifier to buffer the output from heavy loads. Application Tips 4.3.1 INPUT OFFSET VOLTAGE OVER TEMPERATURE Table 1-1 gives both the linear and quadratic temperature coefficients (TC1 and TC2) of input offset voltage. The input offset voltage, at any temperature in the specified range, can be calculated as follows: EQUATION 4-1: V OS ( T A ) = VOS + TC1 T + TC 2 T 2 Where: OFFSET AT POWER UP When this part powers up, the input offset (VOS) starts at its uncorrected value (usually less than 5 mV). Circuits with high DC gain can cause the output to reach one of the two rails. In this case, the time to a valid output is delayed by an output overdrive time (like tODR), in addition to the startup time (like tSTR). It can be simple to avoid this extra startup time. Reducing the gain is one method. Adding a capacitor across the feedback resistor (RF) is another method. 4.3.4 The output voltage range of the MCP6V27 zero-drift op amp is VDD - 15 mV (minimum) and VSS + 15 mV (maximum) when RL = 10 k is connected to VDD/2 and VDD = 5.5V. Refer to Figure 2-19 and Figure 2-20. 4.3 4.3.3 SOURCE RESISTANCES The input bias currents have two significant components; switching glitches that dominate at room temperature and below, and input ESD diode leakage currents that dominate at +85C and above. Make the resistances seen by the inputs small and equal. This minimizes the output offset caused by the input bias currents. The inputs should see a resistance on the order of 10 to 1 k at high frequencies (i.e., above 1 MHz). This helps minimize the impact of switching glitches, which are very fast, on overall performance. In some cases, it may be necessary to add resistors in series with the inputs to achieve this improvement in performance. 4.3.5 SOURCE CAPACITANCE The capacitances seen by the two inputs should be small and matched. The internal switches connected to the inputs dump charges on these capacitors; an offset can be created if the capacitances do not match. T = TA - 25C 4.3.6 VOS(TA) = input offset voltage at TA VOS = input offset voltage at +25C TC1 = linear temperature coefficient TC2 = quadratic temperature coefficient Driving large capacitive loads can cause stability problems for voltage feedback op amps. As the load capacitance increases, the feedback loop's phase margin decreases and the closed-loop bandwidth is reduced. This produces gain peaking in the frequency response, with overshoot and ringing in the step response. These auto-zeroed op amps have a different output impedance than most op amps, due to their unique topology. 4.3.2 DC GAIN PLOTS Figure 2-9, Figure 2-10 and Figure 2-11 are histograms of the reciprocals (in units of V/V) of CMRR, PSRR and AOL, respectively. They represent the change in input offset voltage (VOS) with a change in common mode input voltage (VCM), power supply voltage (VDD) and output voltage (VOUT). The 1/AOL histogram is centered near 0 V/V because the measurements are dominated by the op amp's input noise. The negative values shown represent noise, not unstable behavior. We validate the op amps' stability by making multiple measurements of VOS; an unstable part would show either greater variability in VOS, or the output is stuck at one of the rails. DS25007A-page 22 CAPACITIVE LOADS When driving a capacitive load with these op amps, a series resistor at the output (RISO in Figure 4-7) improves the feedback loop's phase margin (stability) by making the output load resistive at higher frequencies. The bandwidth will be generally lower than the bandwidth with no capacitive load. (c) 2011 Microchip Technology Inc. MCP6V27 RG RISO RF VOUT VOUT RL CL 1/2 MCP6V27 CL 1/2 MCP6V27 FIGURE 4-9: FIGURE 4-7: Output Resistor, RISO, Stabilizes Capacitive Loads. Figure 4-8 gives recommended RISO values for different capacitive loads and gains. The x-axis is the normalized load capacitance (CL/GN2). The y-axis is the normalized resistance (GNRISO). GN is the circuit's noise gain. For non-inverting gains, GN and the Signal Gain are equal. For inverting gains, GN is 1+|Signal Gain| (e.g., -1 V/V gives GN = +2 V/V). 4.3.8 Output Load. GAIN PEAKING Figure 4-10 shows an op amp circuit that represents non-inverting amplifiers (VM is a DC voltage and VP is the input) or inverting amplifiers (VP is a DC voltage and VM is the input). The capacitances CN and CG represent the total capacitance at the input pins; they include the op amp's common mode input capacitance (CCM), board parasitic capacitance and any capacitor placed in parallel. Recommended GNRISO () 1000 1k VP 100 100 VM 10 GN = 1 GN = 2 GN = 5 GN 10 11 100p 1.E-10 1n 1.E-09 10n 100n 1.E-08 2 1.E-07 CL/GN (F) 1 1.E-06 FIGURE 4-8: Recommended RISO values for Capacitive Loads. After selecting RISO for your circuit, double check the resulting frequency response peaking and step response overshoot. Modify RISO's value until the response is reasonable. Bench evaluation and simulations with the MCP6V27 SPICE macro model are helpful. 4.3.7 STABILIZING OUTPUT LOADS This auto-zeroed op amp has an output impedance (Figure 2-31 and Figure 2-32) that has a double zero when the gain is low. This can cause a large phase shift in feedback networks that have low resistance near the part's bandwidth. This large phase shift can cause stability problems. Figure 4-9 shows that the load on the output is (RL + RISO)||(RF + RG), where RISO is before the load (like Figures 4-7). This load needs to be large enough to maintain stability; it should be at least (2 k)/GN. (c) 2011 Microchip Technology Inc. RN RG FIGURE 4-10: Capacitance. CN 1/2 MCP6V27 CG VOUT RF Amplifier with Parasitic CG acts in parallel with RG (except for a gain of +1 V/V), which causes an increase in gain at high frequencies. CG also reduces the phase margin of the feedback loop, which becomes less stable. This effect can be reduced by either reducing CG or RF||RG. CN and RN form a low-pass filter that affects the signal at VP. This filter has a single real pole at 1/(2RNCN). The largest value of RF that should be used depends on noise gain (see GN in Section 4.3.6, Capacitive Loads), CG and the open-loop gain's phase shift. An approximate limit for RF is: EQUATION 4-2: 12 pF 2 RF 2 k x --------------- x G N CG Some applications may modify these values to reduce either output loading or gain peaking (step response overshoot). DS25007A-page 23 MCP6V27 4.3.9 REDUCING UNDESIRED NOISE AND SIGNALS Reduce undesired noise and signals with: * Low bandwidth signal filters: - Minimizes random analog noise - Reduces interfering signals * Good PCB layout techniques: - Minimizes crosstalk - Minimizes parasitic capacitances and inductances that interact with fast switching edges * Good power supply design: - Provides isolation from other parts - Filters interference on supply line(s) 4.3.10 SUPPLY BYPASSING AND FILTERING With this operational amplifier, the power supply pin (VDD for single supply) should have a local bypass capacitor (i.e., 0.01 F to 0.1 F) within 2 mm of the pin for good high-frequency performance. This part also needs a bulk capacitor (i.e., 1 F or larger) within 100 mm to provide large, slow currents. This bulk capacitor can be shared with other low noise, analog parts. In some cases, high-frequency power supply noise (e.g., switched mode power supplies) may cause undue intermodulation distortion, with a DC offset shift; this noise needs to be filtered. Adding a resistor into the supply connection can be helpful. This resistors needs to be small enough to prevent a large drop in VDD for the op amp, which would cause a reduced output range and possible load-induced power supply noise. It also needs to be large enough to dissipate little power when VDD is turned on and off quickly. Figure 4-11 shows a circuit with resistors in the supply connections. It gives good rejection out to 1 MHz for switched mode power supplies. Smaller resistors and capacitors are a better choice for designs where the power supply is not as noisy. VS_ANA 50 1/4W 50 1/10W 100 F 100 F to other analog parts FIGURE 4-11: DS25007A-page 24 0.1 F 1/2 MCP6V27 Additional Supply Filtering. 4.3.11 PCB DESIGN FOR DC PRECISION In order to achieve DC precision on the order of 1 V, many physical errors need to be minimized. The design of the Printed Circuit Board (PCB), the wiring and the thermal environment has a strong impact on the precision achieved. A poor PCB design can easily be more than 100 times worse than the MCP6V27 op amp minimum and maximum specifications. 4.3.11.1 PCB Layout Any time two dissimilar metals are joined together, a temperature dependent voltage appears across the junction (the Seebeck or thermo-junction effect). This effect is used in thermocouples to measure temperature. The following are examples of thermo-junctions on a PCB: * Components (resistors, op amps, ...) soldered to a copper pad * Wires mechanically attached to the PCB * Jumpers * Solder joints * PCB vias Typical thermo-junctions have temperature to voltage conversion coefficients of 10 to 100 V/C (sometimes higher). Microchip's AN1258 ("Op Amp Precision Design: PCB Layout Techniques") contains in depth information on PCB layout techniques that minimize thermo-junction effects. It also discusses other effects, such as crosstalk, impedances, mechanical stresses and humidity. 4.3.11.2 Crosstalk DC crosstalk causes offsets that appear as a larger input offset voltage. Common causes include: * Common mode noise (remote sensors) * Ground loops (current return paths) * Power supply coupling Interference from the mains (usually 50 Hz or 60 Hz), and other AC sources, can also affect the DC performance. Non-linear distortion can convert these signals to multiple tones, included a DC shift in voltage. When the signal is sampled by an ADC, these AC signals can also be aliased to DC, causing an apparent shift in offset. To reduce interference: - Keep traces and wires as short as possible Use shielding (e.g., encapsulant) Use ground plane (at least a star ground) Place the input signal source near to the DUT Use good PCB layout techniques Use a separate power supply filter (bypass capacitors) for these auto-zeroed op amps (c) 2011 Microchip Technology Inc. MCP6V27 4.3.11.3 Miscellaneous Effects 1/2 MCP6V27 Keep the resistances seen by the input pins as small and as near to equal as possible to minimize bias current related offsets. Make the (trace) capacitances seen by the input pins small and equal. This is helpful in minimizing switching glitch-induced offset voltages. Bending a coax cable with a radius that is too small causes a small voltage drop to appear on the center conductor (the tribo-electric effect). Make sure the bending radius is large enough to keep the conductors and insulation in full contact. 200 VDD R R 1 F 200 R R 10 nF 4.4.1 Figure 4-12 shows how to interface to a Wheatstone bridge with a minimum of components. Because the circuit is not symmetric, the ADC input is single ended, and there is a minimum of filtering, the CMRR is good enough for moderate common mode noise. 20 k High Performance Design. RTD SENSOR The ratiometric circuit in Figure 4-14 conditions a three wire RTD. It corrects for the sensor's wiring resistance by subtracting the voltage across the middle RW. The top R1 does not change the output voltage; it balances the op amp inputs. Failure (open) of the RTD is detected by an out-of-range voltage. 1/2 MCP6V27 2.49 k VDD 0.01C VDD R R R R 0.2R VDD 3 k 100R ADC 1/2 MCP6V27 FIGURE 4-12: RW RRTD 100 Simple Design. Figure 4-13 shows a higher performance circuit for Wheatstone bridges. This circuit is symmetric and has high CMRR. Using a differential input to the ADC helps with the CMRR. 100 nF RT 20 k 10 nF 0.2R 3 k 1/2 MCP6V27 4.4.2 Many sensors are configured as Wheatstone bridges. Strain gauges and pressure sensors are two common examples. These signals can be small and the common mode noise large. Amplifier designs with high differential gain are desirable. ADC 200 FIGURE 4-13: WHEATSTONE BRIDGE VDD 1 F Humidity can cause electro-chemical potential voltages to appear in a circuit. Proper PCB cleaning helps, as does the use of encapsulants. Typical Applications 3 k 1 F 200 Mechanical stresses can make some capacitor types (such as ceramic) to output small voltages. Use more appropriate capacitor types in the signal path and minimize mechanical stresses and vibration. 4.4 20 k 10 nF R1 2.49 k 1 F 10 nF RW R1 2.49 k RB 20 k R3 100 k R2 2.55 k 3 k VDD ADC R2 2.55 k R3 100 k 3 k 100 nF RW 2.49 k 1/2 MCP6V27 FIGURE 4-14: (c) 2011 Microchip Technology Inc. RTD Sensor. DS25007A-page 25 MCP6V27 The voltages at the input of the ADC can be calculated with the following: G RTD = 1 + 2 R3 R 2 G W = G RTD - R3 R 1 VDM = G RTD ( VT - V B ) + G W VW V T + V B + ( G RTD + 1 - G W )VW VCM = -----------------------------------------------------------------------------2 Where: VT = Voltage at the top of RRTD VB = Voltage at the bottom of RRTD VW = Voltage across top and middle RW's VCM = ADC's common mode input VDM = ADC's differential mode input 4.4.3 EQUATION 4-3: V1 THJ(40 V/C) V3 = TCJ(10 mV/C) + (0.50V) V4 = 250V1 + (V2 - V3) (10 mV/C) (THJ - TCJ) + (0.50V) FIGURE 4-15: Simplified Circuit. (RTH) V4 FIGURE 4-16: Thermocouple Sensor. The MCP1541 produces a 4.10V output, assuming VDD is at 5.0V. This voltage, tied to a resistor ladder of 4.100(RTH) and 1.3224(RTH), would produce a Thevenin equivalent of 1.00V and 250(RTH). The 1.3224(RTH) resistor is combined in parallel with the top right RTH resistor (in Figure 4-15), producing the 0.5696(RTH) resistor. OFFSET VOLTAGE CORRECTION Figure 4-17 shows an MCP6V27 correcting the input offset voltage of another op amp. R2 and C2 integrate the offset error seen at the other op amp's input; the integration needs to be slow enough to be stable (with the feedback provided by R1 and R3). VIN R1 R2 R3 C2 VOUT R4 MCP661 (RTH) R2 VDD/2 FIGURE 4-17: DS25007A-page 26 V4 3 k The MCP9700A senses the temperature at its physical location. It needs to be at the same temperature as the cold junction (TCJ), and produces V3 (Figure 4-15). C Thermocouple Sensor; (RTH) (RTH) 4.4.4 (hot junction RTH = Thevenin Equivalent Resistance at THJ) (RTH) (RTH) V 2 40 V/C C Type K Thermocouple (RTH)/250 1/2 MCP6V27 V3 C V4 should be converted to digital, then corrected for the thermocouple's non-linearity. The ADC can use the MCP1541 as its voltage reference. Alternately, an absolute reference inside a PICmicro(R) device can be used instead of the MCP1541. V2 = (1.00V) (cold junction at TCJ) (RTH)/250 MCP9700A Figure 4-15 shows a simplified diagram of an amplifier and temperature sensor used in a thermocouple application. The type K thermocouple senses the temperature at the hot junction (THJ), and produces a voltage at V1 proportional to THJ (in C). The amplifier's gain is set so that V4/THJ is 10 mV/C. V3 represents the output of a temperature sensor, which produces a voltage proportional to the temperature (in C) at the cold junction (TCJ), and with a 0.50V offset. V2 is set so that V4 is 0.50V when THJ - TCJ is 0C. (RTH)/250 RTH = Thevenin Equivalent Resistance (e.g., 10 k) VDD 4.100(RTH) 0.5696(RTH) MCP1541 C (R )/250 TH Type K 1/2 MCP6V27 V1 VDD THERMOCOUPLE SENSOR V1 Figure 4-16 shows a more complete implementation of this circuit. The dashed red arrow indicates a thermally conductive connection between the thermocouple and the MCP9700A; it needs to be very short and have low thermal resistance. R5 1/2 MCP6V27 VDD/2 Offset Correction. (c) 2011 Microchip Technology Inc. MCP6V27 4.4.5 PRECISION COMPARATOR Use high gain before a comparator to improve the latter's performance. Do not use MCP6V27 as a comparator by itself; the VOS correction circuitry does not operate properly without a feedback loop. 1/2 MCP6V27 VIN R1 R2 R3 R4 R5 1 k VOUT VDD/2 MCP6541 FIGURE 4-18: Precision Comparator. (c) 2011 Microchip Technology Inc. DS25007A-page 27 MCP6V27 NOTES: DS25007A-page 28 (c) 2011 Microchip Technology Inc. MCP6V27 5.0 DESIGN AIDS Microchip provides the basic design aids needed for the MCP6V27 op amp. 5.1 SPICE Macro Model The latest SPICE macro model for the MCP6V27 op amp is available on the Microchip web site at www.microchip.com. This model is intended to be an initial design tool that works well in the op amp's linear region of operation over the temperature range. See the model file for information on its capabilities. Bench testing is a very important part of any design and cannot be replaced with simulations. Also, simulation results using this macro model need to be validated by comparing them to the data sheet specifications and characteristic curves. 5.2 FilterLab(R) Software Microchip's FilterLab(R) software is an innovative software tool that simplifies analog active filter (using op amps) design. Available at no cost from the Microchip web site at www.microchip.com/filterlab, the Filter-Lab design tool provides full schematic diagrams of the filter circuit with component values. It also outputs the filter circuit in SPICE format, which can be used with the macro model to simulate actual filter performance. 5.3 Microchip Advanced Part Selector (MAPS) MAPS is a software tool that helps efficiently identify Microchip devices that fit a particular design requirement. Available at no cost from the Microchip website at www.microchip.com/maps, the MAPS is an overall selection tool for Microchip's product portfolio that includes Analog, Memory, MCUs and DSCs. Using this tool, a customer can define a filter to sort features for a parametric search of devices and export side-by-side technical comparison reports. Helpful links are also provided for Data sheets, Purchase and Sampling of Microchip parts. 5.4 Analog Demonstration and Evaluation Boards Microchip offers a broad spectrum of Analog Demonstration and Evaluation Boards that are designed to help customers achieve faster time to market. For a complete listing of these boards and their corresponding user's guides and technical information, visit the Microchip web site at www.microchip.com/analog tools. Some boards that are especially useful are: * MCP6V01 Thermocouple Auto-Zeroed Reference Design * MCP6XXX Amplifier Evaluation Board 1 * MCP6XXX Amplifier Evaluation Board 2 * MCP6XXX Amplifier Evaluation Board 3 * MCP6XXX Amplifier Evaluation Board 4 * Active Filter Demo Board Kit * P/N SOIC8EV: 8-Pin SOIC/MSOP/TSSOP/DIP Evaluation Board * P/N SOIC14EV: 14-Pin SOIC/TSSOP/DIP Evaluation Board 5.5 Application Notes The following Microchip Application Notes are available on the Microchip web site at www.microchip. com/appnotes and are recommended as supplemental reference resources. ADN003: "Select the Right Operational Amplifier for your Filtering Circuits", DS21821 AN722: "Operational Amplifier Topologies and DC Specifications", DS00722 AN723: "Operational Amplifier AC Specifications and Applications", DS00723 AN884: "Driving Capacitive Loads With Op Amps", DS00884 AN990: "Analog Sensor Conditioning Circuits - An Overview", DS00990 AN1177: "Op Amp Precision Design: DC Errors", DS01177 AN1228: "Op Amp Precision Design: Random Noise", DS01228 AN1258: "Op Amp Precision Design: PCB Layout Techniques", DS01258 These application notes and others are listed in the design guide: "Signal Chain Design Guide", DS21825 (c) 2011 Microchip Technology Inc. DS25007A-page 29 MCP6V27 NOTES: DS25007A-page 30 (c) 2011 Microchip Technology Inc. MCP6V27 6.0 PACKAGING INFORMATION 6.1 Package Marking Information 8-Lead DFN (4x4 mm) XXXX YYWW NNN PIN 1 8-Lead MSOP Example 6V27 e3 E/MD^^ 1105 256 PIN 1 Example 6V27E 105256 8-Lead SOIC (150 mil) Example MCP6V27E SN^^ e31105 256 NNN Legend: XX...X Y YY WW NNN e3 * Note: Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2011 Microchip Technology Inc. DS25007A-page 31 MCP6V27 8-Lead Plastic Dual Flat, No Lead Package (MD) - 4x4x0.9 mm Body [DFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Microchip Technology Drawing C04-131E Sheet 1 of 2 DS25007A-page 32 (c) 2011 Microchip Technology Inc. MCP6V27 8-Lead Plastic Dual Flat, No Lead Package (MD) - 4x4x0.9 mm Body [DFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Microchip Technology Drawing C04-131E Sheet 2 of 2 (c) 2011 Microchip Technology Inc. DS25007A-page 33 MCP6V27 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS25007A-page 34 (c) 2011 Microchip Technology Inc. MCP6V27 1 % & %! % 2" ) ' % 2 $% %"% %% 033)))& &3 2 D N E E1 NOTE 1 1 2 e b A2 A c L L1 A1 4% & 5&% 6!&( $ 55* * 6 6 67 8 9 % 7 ; % < < + 9+ + < + ""2 2 %" $$ :+./ 7 ="% * ""2="% * ,./ 7 5% ,./ 1 %5% 5 1 % % 5 1 % 5" 2 ./ : 9 +*1 > < 9> 9 < , 5"="% ( < !"#$%! & '(!%&! %( %")% % % " & "*" %!"& "$ % ! "$ % ! %#"+&& " , & "% *-+ ./0 . & %#%! ))% !%% *10 $ & '! !)% !%% '$ $ &% ! (c) 2011 Microchip Technology Inc. ) /. DS25007A-page 35 MCP6V27 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS25007A-page 36 (c) 2011 Microchip Technology Inc. MCP6V27 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging (c) 2011 Microchip Technology Inc. DS25007A-page 37 MCP6V27 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS25007A-page 38 (c) 2011 Microchip Technology Inc. MCP6V27 !"#$%&'() 1 % & %! % 2" ) ' % 2 $% %"% %% 033)))& &3 2 (c) 2011 Microchip Technology Inc. DS25007A-page 39 MCP6V27 NOTES: DS25007A-page 40 (c) 2011 Microchip Technology Inc. MCP6V27 APPENDIX A: REVISION HISTORY Revision A (March 2011) * Original Release of this Document. (c) 2011 Microchip Technology Inc. DS25007A-page 41 MCP6V27 APPENDIX B: OFFSET RELATED TEST SCREENS - Greater accuracy We use production screens to ensure the quality of our outgoing products. These screens are set at wider limits to eliminate any fliers; see Table B-1. Input offset voltage related specifications in the DC spec table (Table 1-1) are based on bench measurements (see Section 2.1 "DC Input Precision"). These measurements are much more accurate because: * More compact circuit * Soldered parts on the PCB (to validate other measurements) * More time spent averaging (reduces noise) * Better temperature control - Reduced temperature gradients TABLE B-1: OFFSET RELATED TEST SCREENS Electrical Characteristics: Unless otherwise indicated, TA = +25C, VDD = +2.3V to +5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2 and RL = 10 k to VL (refer to Figure 1-4 and Figure 1-5). Parameters Sym Min Max Units Conditions Input Offset Voltage VOS -10 +10 V Input Offset Voltage Drift with Temperature (linear Temp. Co.) TC1 -- -- PSRR 115 -- dB (Note 1) CMRR 106 -- dB VDD = 2.3V, VCM = -0.15V to 2.5V (Note 1) CMRR 116 -- dB VDD = 5.5V, VCM = -0.15V to 5.7V (Note 1) AOL 114 -- dB VDD = 2.3V, VOUT = 0.2V to 2.1V (Note 1) AOL 122 -- dB VDD = 5.5V, VOUT = 0.2V to 5.3V (Note 1) Input Offset Power Supply Rejection TA = +25C (Note 1, Note 2) nV/C TA = -40 to +125C (Note 3) Common Mode Common Mode Rejection Open-Loop Gain DC Open-Loop Gain (large signal) Note 1: 2: 3: Due to thermal junctions and other errors in the production environment, these specifications are only screened in production. VOS is also sample screened at +125C. TC1 is not measured in production. DS25007A-page 42 (c) 2011 Microchip Technology Inc. MCP6V27 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. -X /XX Device Temperature Range Package Device: MCP6V27 Dual Op Amp MCP6V27T Dual Op Amp (Tape and Reel) Temperature Range: E Package: MD MS SN Examples: a) b) Extended temperature, 8LD 4x4 DFN package MCP6V27T-E/MD: Tape and Reel Extended temperature, 8LD 4x4 DFN package c) MCP6V27-E/MS: d) Extended temperature, 8LD MSOP package MCP6V27T-E/MS: Tape and Reel, Extended temperature, 8LD MSOP package. e) MCP6V27-E/SN: = -40C to +125C = Plastic Dual Flat, No-Lead (4x4x0.9 mm), 8-lead = Plastic Micro Small Outline Package, 8-lead = Plastic SOIC (150 mil Body), 8-lead (c) 2011 Microchip Technology Inc. MCP6V27-E/MD: f) Extended temperature, 8LD SOIC package. MCP6V27T-E/SN: Tape and Reel, Extended temperature, 8LD SOIC package. DS25007A-page 43 MCP6V27 NOTES: DS25007A-page 44 (c) 2011 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2011, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-61341-020-2 Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2011 Microchip Technology Inc. DS25007A-page 45 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7830 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 02/18/11 DS22049F-page 46 (c) 2011 Microchip Technology Inc.