for customized programming Operates with Industry Standard Dimmers Compact Encapsulated Assembly Active Power Factor Correction Output Over-Voltage, Over-Current and Short-Circuit Protection and Auto Recovery High Temperature Operation (up to 90C case) UL Approved, ENEC Approved, CE Mark Long Life ROHS Compliant EVM Series 60-120 W Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming TROPO is designed for powering LED luminaries with standard lighting contro Standard Light Switches Triac based Incandescent Dimmers (Standard phase - leading edge Electronic Low Voltage Dimmers (Reverse Phase - trailing edge) Input& Voltage Max.& Output& Power Output& Voltage Output& Current Efficiency Max.&Case& Temperature Power& Dimming& Startup& &THD TROPO isFactor ideal forDimming&Method installations requiring Range dimmable Time Class 2 outputs such as 90#to#305# Vac# maximum 120#W 30#to#84#Vdc 1.05#to#2.8#A# CC# #87%# typical 90C# (measured#at# the#hot#spot) <#20% CC: Constant Current >#0.9 ForwardIPhase, Commercial Lighting 1#I#100% ReverseIPhase 400#ms (%#of#Iout) �#I#10V Residential Lig The following diagram depicts a typical installation utilizing the TROPO: + Dim TRIAC Dimmer FEATURES * CompaHble with TRIAC (forward-phase or leading-edge) / ELV (reverse-phase or trailing-edge) and 0-10 V dimmers * TRIAC dimming only at 120 Vac * Outdoor surge protecHon: 3 kV line to line/6 kV line to earth * Linear 0-10V dimming transfer funcHon: 10V=100%, 1V=10%, 0.1V=1% * ProtecHons: output open load, over-current and short-circuit (hiccup), and over-temperature with auto recovery * Conducted and radiated EMI: Compliant with FCC CFR Title 47 Part 15 Class B (120 Vac)/Class A (277 Vac) and EN55015 (CISPR 15) at 220/230/240 Vac * Enables ENERGY STAR(R) and DLC (DesignLight ConsorHum(R)) luminaire compliance * IP20-rated Boom Leads with Studs metal case with silicone-based poang. OpHonal IP64 metal case with side leads * LifeHme: 50,000 hours * 90C maximum case hot spot temperature * Class 2 power supply (only some models) * Double-insulated power supply between input and output (class II) * Worldwide safety approvals Dimmer - Dim Triac Based Dimmer + LEDs 0-10 V Dimmer EVM110 TROPO - LEDs APPLICATION DIAGRAM METAL CASE L 144 x W 70 x H 40 mm (L 5.67 x W 2.76 x H 1.57 in) APPLICATIONS * High Bay Lights Industrial LED LighHng * Metal Halide replacement Tunnels and street lighHng * Outdoor LED LighHng Wide-area downlights * Suitable for driving high current COB LEDs such as Cree's CXA3050/3070/3590, Bridgelux' Vero series and modules such as Cree's LMH020 6000/8000 Purple: + Dim White: Neutral Black: Line LED DRIVER Grey: - Dim Red: + LEDs Black: - LEDs WIRING DIAGRAM (c) ERP - ENERGY RECOVERY PRODUCTS 1 EVM Series Data Sheet December 7, 2014 - rev. A Di 10 Ou du Ou to M m di Fa St EVM Series 60-120 W Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming 1 - INPUT SPECIFICATION (@25C ambient temperature) Units Minimum Vac 90 Hz 47 0.9 AC5Line5Input5Voltage5Range5 (Vin) Input5Frequency5Range Power5Factor5(PF) Inrush5Current A Typical 120/220/230/ 240/277 600/050 >00.9 Maximum 305 63 Meets0NEMAL4100requirements At0nominal0input0voltage At0any0point0on0the0sine0wave0and025C 2500A0@012000Vac 5000A0@02300Vac Measured0per0IEC60950L1 6000A0@02770Vac Complies0with0IEC61000L3L20for0Class0C0equipment Leakage5Current A Input5Harmonics Total5Harmonics5Distortion5 (THD) 20% 87% 89% Efficiency Isolation Notes L !At00nominal0input0voltage0and0nominal0LED0load !Complies0with0DLC0(DesignLight0Consortium)0 000technical0requirements0v2.1 !At01200Vac !At02770Vac Meets0UL60950L10for0class0II0reinforced/double0insulation0power0supply 2 - OUTPUT SPECIFICATION (@25C ambient temperature) Units Minimum Typical Maximum Notes Vdc 30 84.0 See+ordering+information+for+details A 1.05 2.8 See+ordering+information+for+details % <5 2.5 +5 Includes+AC+line+voltage,+load,+and+current+set+point+variations The driver does not operate outside of the regulation requirements for more Output4Current4Overshoot % < < 10 than+500+ms+during+power+on+with+nominal+LED+load+and+without+dimmer. <+25%+peak%300,000%hours%when%operated%at%nominal%input%and%output%conditions,%and%at%Tc%%70C Lifetime 50,000%hours%at%70C%maximum%case%hot%spot%temperature%(see%hot%spot%!tc%on%label%in%page%10)% 4 - EMC COMPLIANCE AND SAFETY APPROVALS Conducted)and)Radiated)EMI Harmonic)Current)Emissions Voltage)Fluctuations)&)Flicker ESD)(Electrostatic) Discharge) RF)Electromagnetic)Field) Susceptibility Immunity) Electrical)Fast)Transient Compliance Surge Conducted)RF) Disturbances Voltage)Dips Transient)Protection Ring)Wave UL cUL CE EMC)Compliance !FCC-CFR-Title-47-Part-15-Class-B-at-120-Vac-and-Class-A-at-277-Vac, !EN55015-(CISPR-15)-compliant-at-220/230/240-Vac IEC61000'3'2 For-Class-C-equipment IEC61000'3'3 IEC61000'4'2 6-kV-contact-discharge,-8-kV-air-discharge,-level-3 IEC61000'4'3 3-V/m,-80-'-1000-MHz,-80%-modulated-at-a-distance-of-3-meters IEC61000'4'4 -2-kV-on-AC-power-port-for-1-minute,-1-kV-on-signal/control-lines -3-kV-line-to-line-(differential-mode)-/-6-kV-line-to-common-mode-ground(tested-to-secondary-ground)-on-on-AC-power-port,-0.5-kV-for-outdoor-cables IEC61000'4'5 IEC61000'4'6 3-V,-0.15'80-MHz,-80%-modulated IEC61000'4'11 >95%-dip,-0.5-period;-30%-dip,-25-periods;-95%-reduction,-250-periods ANSI/IEEE-c62.41.1'2002-&-c62.41.2'2002-category-A,-2.5-kV-ring-wave Safety)Agency)Approvals UL8750-recognized -UL60950'1-recognized CSA-C22.2-60950'1 IEC61347'2'13-electronic-control-gear-for-LED-Modules Hi4Pot4(High4Potential) SaveEnergy@ERPpowerllc.com Units Minimum Vdc 4242 Safety Typical 3 Maximum Notes !Insulation/between/the/input/(AC/line/and/Neutral)/ and/the/output !Tested/at/the/RMS/voltage/equivalent/of/3000/Vac www.ERPpowerllc.com EVM Series 60-120 W Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming 5 - PROTECTION FEATURES Under-Voltage (Brownout) The EVM series provides protecHon circuitry such that an applicaHon of an input voltage below the minimum stated in paragraph 1 (Input SpecificaHon) shall not cause damage to the driver. Short Circuit The EVM series is protected against short-circuit such that a short from any output to return shall not result in a fire hazard or shock hazard. The driver shall hiccup as a result of a short circuit or over current fault. Removal of the fault will return the driver to within normal operaHon. The driver shall recover, with no damage, from a short across the output for an indefinite period of Hme. Internal Over temperature ProtecJon The EVM series incorporates circuitry that prevents internal damage due to an over temperature condiHon. An over temperature condiHon may be a result of an excessive ambient temperature or as a result of an internal failure. When the over temperature condiHon is removed, the driver shall automaHcally recover. Output Open Load When the LED load is removed, the output voltage of the EVM series is limited to 1.3 Hmes the maximum output voltage of each model. SaveEnergy@ERPpowerllc.com 4 www.ERPpowerllc.com EVM Series 60-120 W Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming Percent of Output Current (Normalized to Rated Current 6 - PHASE-CUT DIMMING Dimming of the driver is possible with standard TRIAC-based incandescent dimmers that chop the AC voltage as shown in Figure 1, or with ELV dimmers. During the rapid rise Hme of the AC voltage when the dimmer turns on, the driver does not generate any voltage or current oscillaHons, and inrush current is controlled. During the on-Hme of the AC input, the driver regulates the output current based upon the conducHon angle. The RMS value of the driver output current is proporHonal to the on-Hme of the AC input voltage. When operaHng with an incandescent dimmer, the RMS output current varies depending upon the conducHon angle and RMS value of the applied AC input voltage. Figure 2 shows the typical output current versus conducHon angle at nominal input voltage. Chopped AC Input to Driver AC Wall Power 120% Output Current versus ConducJon Angle 100% 80% 120 Vac 60% 40% 20% 0% 0 Figure 1 50 100 150 ConducJon Angle 200 Figure 2 7 - COMPATIBLE PHASE-CUT DIMMERS & DIMMING RANGE 120Vac'Dimmers' Mfg.' Model' Mfg.' Model' Mfg.' Model' Lutron' S"603PG( Lutron( DVELV"303P( Lutron( CT"103P( Leviton' IPI06"1LZ( Lutron( SELV"300P( Cooper( SLC03P( Leviton' 6631"2( Leviton'( 6683"IW( Leviton( IPE04( Lutron' DVCL"153P( Leviton( 6161( Lutron( MAELV"600( Lutron' DV"600P( Leviton'( 6633"P( Lutron( FAELV"500( Lutron' TGCL"153P( Lutron( TG"600P( Lightolier'( ZP260QEW( Lutron' S"600P( Cooper( DLC03P( Cooper( DAL06P( Leviton' VPE06( Lutron( LG"600P( ( ( SaveEnergy@ERPpowerllc.com 5 www.ERPpowerllc.com EVM Series 60-120 W Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming 8 - 0-10 V DIMMING The EVM drivers operate only with 0-10V dimmers that sink current. They are not designed to operate with 0-10V control systems that source current, as used in theatrical/entertainment systems. Developed in the 1980's, the 0-10V sinking current control method is adopted by the InternaHonal Electrotechnical Commission (IEC) as apart of their IEC Standard 60929 Annex E. The method to dim the output current of the driver is done via the +Dim/-Dim Signal pins. The +Dim/-Dim Signal pins respond to a 0 to 10 V signal, delivering 1% to 100% of the output current based on rated current for each model. A pull-up resistor is included internal to the driver. When the +Dim input (purple) is short circuited to the -Dim wire (grey) or to the -LED wire (black), there is no output current. When the +Dim input (purple) is 1 V, the output current is programmed to 10% of rated current. If the +Dim input is >10V or open circuited, the output current is programmed to 100% of the rated current. When not used, the -Dim wire (grey) and to the +Dim wire (purple) can be capped or cut off. In this configuraHon, no dimming is possible and the driver delivers 100% of its rated output current. The maximum source current (flowing from the driver to the 0-10V dimmer) supplied by the +Dim Signal pin is < 1 mA. The tolerance of the output current while being dimmed shall be +/-8% typical unHl down to 2V. There are two 0-10V dimming transfer funcHons available, a linear curve where 10V = 100% of the output current and 1V = 10% of the output current (seen in figure 3) or a non-linear curve where the 9V = 100% of the output current and 1V = 1% of the output current (seen in figure 4). The non-linear curve is recommended when using standard in wall 0-10V logarithmic dimmers to avoid having insufficient source current available to pull the dimmer up to 10V and to account for the inability of the dimmer to pull below approximately 0.9V. In these types of installaHons, the modified transfer funcHon will ensure 100% light output and dimming to 1%, regardless of the number of drivers on the 0-10V dimming line. Normalized Output Current vs Dimming Voltage Percent of Output Current (Normalized to Rated Current Percent of Output Current (Normalized to Rated Current) 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% Normalized Output Current vs Dimming Voltage 0 1 2 3 4 5 6 7 Dimming Voltage (V) 8 0 9 10 Figure 3 SaveEnergy@ERPpowerllc.com 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 1% 0% 1 2 3 4 5 6 7 Dimming Voltage (V) 8 9 10 Figure 4 6 www.ERPpowerllc.com EVM Series 60-120 W Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming 8 - 0-10 V DIMMING (CONTINUED) Percent of Output Current (Normalized to Rated Current) A fixed or variable resistor can be also used from the dimming input to the return to adjust the output current. Figure 5 show the relaHonship of the output current to a resistor connected across the 0-10V dimming input Normalized Output Current vs Resistance 120% 100% 80% 60% 40% 20% 0% 0 20 40 60 Resistance (k) Figure 5 80 100 9 - COMPATIBLE 0-10 V DIMMERS * Lutron, Nova series (part number NFTV) * Lutron, Diva series (part number DVTV) * Leviton, IllumaTech series (part number IP710-DL) SaveEnergy@ERPpowerllc.com 7 www.ERPpowerllc.com EVM Series 60-120 W Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming 10 - MECHANICAL DETAILS Packaging OpJons: Metal I/O ConnecJons: Flying leads, 18 AWG on power leads, 22 AWG on control leads, 203 mm (8") long, 105C rated, double insulated stranded, stripped by approximately 9.5mm and Hnned. All the wires, on both input and output, have a 300 V insulaHon raHng. Input wires have double insulaHon. Ingress ProtecJon: IP20 rated 11 - OUTLINE DRAWINGS Dimensions: L 144 x W 70 x H 40 mm (L 5.66 x W 2.76 x H 1.57 in) Volume: 403.2 cm3 (24.6 in3) Figure 6 SaveEnergy@ERPpowerllc.com 8 All dimensions are in mm www.ERPpowerllc.com EVM Series 60-120 W Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming 12 - ORDERING INFORMATION - MODEL DESCRIPTION EVM-- Series Nominal Vin * 080 (70 - 80 W) * W (120 to * 090 (81 - 90 W) 277 Vac) * etc... Iout ERP Part Number Vout Max. Nominal Iout Input Voltage (mA) (Vac) Max Output Power (W) Vout Vout Vout No Load Min Nom Max Voltage (Vdc) (Vdc) (Vdc) (Vdc) EVM060W:(up(to(60W EVM060W'1400'42'C0B 120-'-277 1400 58.8 30 37.8 42 50 30 37.8 42 50 70 37 30 75.6 43.2 37.8 84 48 42 100 60 50 66 70 32 72 75.6 40.5 80 84 45 104 100 58.5 40 30 46.8 37.8 52 42 60 50 66 70 32 30 30 72 75.6 40.5 37.8 37.8 80 84 45 42 42 104 100 58.5 50 50 EVM080W:(71/80W EVM080W'1900'42 120-'-277 EVM090W'1050'84 [1] EVM090W'1700'48'N1B [2] EVM090W'2000'42 120-'-277 120-'-277 120-'-277 EVM100W'1200'80 [1] EVM100W'1200'84 [1] EVM100W'2100'45 120-'-277 120-'-277 120-'-277 EVM110W'2000'52'N1B [1][3] EVM110W'2500'42 [1] 120-'-277 120-'-277 1900 79.8 EVM090W:(81/90W 1050 1700 2000 88.2 81.6 84.0 EVM100W:(91/100W 1200 1200 2100 96.0 100.8 94.5 EVM110W:(101/110W 2000 2500 104.0 105.0 EVM120W:(111/120W [1] EVM120W'1400'80 EVM120W'1400'84 [1] EVM120W'2500'45 [1] EVM120W'2700'42 [1] EVM120W'2800'42 [1] 120-'-277 120-'-277 120-'-277 120-'-277 120-'-277 1400 1400 2500 2700 2800 112.0 117.6 112.5 113.4 117.6 Notes: * (1) Not class 2. * (2)The EVM090W-1700-48-N1B is specifically intended to drive the Cree LMH020 6000 module and exhibits a customized 0-10V dimming transfer funcPon. * (3) The EVM110W-2000-52-N1B is specifically intended to drive the Cree LMH020 8000 module and exhibits a customized 0-10V dimming transfer funcPon. * For addiPonal opPons of output current and output voltage, contact your sales representaPve or send an email to: SaveEnergy@ERPPowerLLC.com SaveEnergy@ERPpowerllc.com 9 www.ERPpowerllc.com EVM Series 60-120 W Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming 13 - LABELING The EVM090W-1700-48 is used in figures 7 & 8 as an example to illustrate a typical label. Top Face Bo\om Face Figure 8 Figure 7 USA Headquarters Tel: +1-805-517-1300 Fax: +1-805-517-1411 301 Science Drive, Suite 210 Moorpark, CA 93021, USA CHINA OperaJons Tel: +86-756-6266298 Fax: +86-756-6266299 No. 8 Pingdong Road 2 Zhuhai, Guangdong, China 519060 ERP - Energy Recovery Products (ERP Power, LLC) - reserves the right to make changes without further noHce to any products herein. ERP makes no warranty, representaHon or guarantee regarding the suitability of its products for any parHcular purpose, nor does ERP assume any liability arising out of the applicaHon or use of any product or circuit, and specifically disclaims any and all liability, including without limitaHon special, consequenHal or incidental damages. "Typical" parameters which may be provided in ERP data sheets and/or specificaHons can and do vary in different applicaHons and actual performance may vary over Hme. All operaHng parameters, including "Typicals" must be validated for each customer applicaHon by customer's technical experts. ERP does not convey any license under its patent rights nor the rights of others. ERP products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applicaHons intended to support or sustain life, or for any other applicaHon in which the failure of the ERP product could create a situaHon where personal injury or death may occur. Should Buyer purchase or use ERP products for any such unintended or unauthorized applicaHon, Buyer shall indemnify and hold ERP and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable aorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ERP was negligent regarding the design or manufacture of the part. ERP is an Equal Opportunity/ AffirmaHve AcHon Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. SaveEnergy@ERPpowerllc.com 10 www.ERPpowerllc.com