SHURE MODEL 450 SERIES II
PAGING AND DISPATCHING MICROPHONE
The Shure Model 450 Series II is a high output dynamic mi-
crophone designed for paging and dispatching applications.
This extremely rugged microphone features an omnidirec-
tional pickup pattern and a frequency response tailored for
optimum speech intelligibility. It also includes an impedance
selection switch and a locking press-to-talk switch. The
press-to-talk switch can be converted to a monitor/transmit
switch with the Shure RK199S Split-Bar Conversion Kit.
Features
•
Dual impedance
•
Locking press-to-talk switch
•
Rugged ARMO-DUR
base and case
•
Adjustable height
•
Optional monitor/transmit switch conversion kit
PRESS-TO-TALK SWITCH OPERATION
To operate the control bar as a press–to–talk switch, simply
hold it down and begin speaking. When you are finished
speaking, release the control bar.
To lock the control bar in the “on” position, press it down and
pull it forward. To unlock the control bar, push it back and re-
lease it.
IMPEDANCE SELECTION
To select high or low impedance, move the impedance selec-
tion switch, located under the microphone base, to either the
HIGH or LO position. The switch is factory pre–set to LO.
Shure recommends the low impedance setting if long
lengths of cable are used, or if severe hum is encountered.
Use Shure A95 Line Matching Transformers to match a low
impedance (300 Ω) microphone line to a high impedance
amplifier input.
WIRING CONNECTIONS
Refer to Figure 1 and Table 1 below. For unbalanced opera-
tion, the GREEN wire is connected to the audio input, the
WHITE wire is connected to the audio ground, and the
SHIELD i s connected to chassis ground. In some cases, a u -
dio ground and chassis ground will be the same.
For balanced operation, the GREEN wire is connected to the
positive audio input, the WHITE wire is connected to the
negative audio input, and the SHIELD is connected to chas-
sis ground.
HILO
WHITE
GREEN
SHIELD
BLACK
RED
IMPEDANCE SWITCH PRESS-TO-TALK SWITCH
12 3
GREEN
WHITE
GREEN
ORANGE
RED
YELLOW
BLACK
WIRING DIAGRAM
FIGURE 1
Table 1. Typical Cable-to-Connector Wiring
INPUT TYPE WIRE
COLOR FUNCTION XLR
CONNECTOR 1/4 IN.
PHONE JACK
GREEN AUDIO PIN 2 TIP
UNBALANCED WHITE AUDIO GROUND PIN 3 SLEEVE
SHIELD CHASSIS GROUND PIN 1 SLEEVE
GREEN AUDIO + PIN 2 TIP
BALANCED WHITE AUDIO – PIN 3 RING
SHIELD CHASSIS GROUND PIN 1 SLEEVE
NOTE: The RED a nd B LACK l eads a re n ot p art o f the a udio
circuit. T hese w ires p rovide a c ontact c losure w hen t he p ress-
to-talk s witch i s d epressed. T his c losure m ay b e u sed t o c on-
trol an external relay or a transmit/receive circuit.
CHANGING PTT CIRCUIT TO NORMALLY OPEN
Using microphones in parallel requires a normally open mi-
crophone circuit. To modify the press–to–talk switch so that
it provides a normally open circuit, proceed as follows:
1. Remove the screws, washers, and bottom plate from
the microphone.
2. Unsolder the black, red, and white leads from terminals
2 and 3 of the press–to–talk switch (see Figure 1).
Make
sure these leads are still soldered together. If necessary,
resolder them and insulate the connection.
3. Replace the bottom plate and secure it with the screws
and washers removed in Step 1.
Model 450 Series II User Guide
27B2917 (AC)
2001, Shure Incorporated Printed in Mexico
TRANSMIT/MONITOR SWITCH CONVERSION KIT
When t he o ptional s plit-bar Transmit/Monitor Switch C onver-
sion Kit i s i nstalled, t he M onitor b ar m ust b e d epressed b efore
the Transmit s witch c an b e d epressed, r equiring t he o perator
to verify that the channel is open before transmitting. The
Monitor bar c an be locked in the “on” position. The Transmit
bar is momentary and cannot be locked.
NOTE: Transceiver w iring i nformation m ust b e o btained f rom
the transceiver schematic and/or the manufacturer.
SPECIFICATIONS
Type
Dynamic
Frequency Response
200 to 5,000 Hz (see Figure 2)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
TYPICAL FREQUENCY RESPONSE
FIGURE 2
Polar Pattern
Omnidirectional
Impedance (at 1,000 Hz)
High Impedance: 30,000 Ω
Low Impedance: 225 Ω
Recommended Load Impedance
High Impedance: 100,000 Ω
Low Impedance: 1,000 Ω
Output Level (at 1,000 Hz, Open Circuit Voltage)
High Impedance Low Impedance
–35.0 dBV/Pa* –57.0 dBV/Pa*
(17.8 mV) (1.4 mV)
*1 Pa = 94 dB SPL
Switches
Locking Press-to-Talk Switch: Activates microphone cir-
cuit and an external relay or control circuit. The micro-
phone circuit is normally shorted.
Impedance Selection Switch: Double-pole, double-throw
slide switch located in the base of the microphone.
Cable
2.1 m (7 ft.) four-conductor, two conductors shielded,
non-detachable
Case
Two-tone gray ARMO-DUR
OVERALL DIMENSIONS
FIGURE 3
Net Weight
737 grams (1 lb., 10 oz.)
Shipping Weight
1020 grams (2 lb., 4 oz.)
Certification
Conforms to European Union directives, eligible to bear
CE marking; meets European Union EMC Immunity Re-
quirements (EN 50082–1, 1992).
REPLACEMENT PARTS
Cartridge R96. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable C31C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
On/Off Switch RK141S. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONAL ACCESSORIES
Transmit/Monitor Split-Bar Switch Kit RK199S. . . . . . . . .
SHURE Incorporated Web Address: http://www.shure.com
222 Hartrey Avenue, Evanston, IL 60202–3696, U.S.A.
Phone: 847-866–2200 Fax: 847-866-2279
In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414
In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055
Elsewhere, Phone: 847-866–2200 Fax: 847-866-2585
