DS90LV110AT
www.ti.com
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
DS90LV110AT 1 to 10 LVDS Data/Clock Distributor with Failsafe
Check for Samples: DS90LV110AT
1FEATURES DESCRIPTION
DS90LV110A is a 1 to 10 data/clock distributor
2• Low jitter 400 Mbps fully differential data path utilizing LVDS (Low Voltage Differential Signaling)
• 145 ps (typ) of pk-pk jitter with PRBS = 223−1technology for low power, high speed operation. Data
data pattern at 400 Mbps paths are fully differential from input to output for low
• Single +3.3 V Supply noise generation and low pulse width distortion. The
design allows connection of 1 input to all 10 outputs.
• Balanced output impedance LVDS I/O enable high speed data transmission for
• Output channel-to-channel skew is 35ps (typ) point-to-point interconnects. This device can be used
• Differential output voltage (VOD) is 320mV (typ) as a high speed differential 1 to 10 signal distribution
with 100Ωtermination load. / fanout replacing multi-drop bus applications for
higher speed links with improved signal quality. It can
• LVDS receiver inputs accept LVPECL signals also be used for clock distribution up to 200MHz.
• LVDS input failsafe The DS90LV110A accepts LVDS signal levels,
• Fast propagation delay of 2.8 ns (typ) LVPECL levels directly or PECL with attenuation
• Receiver open, shorted, and terminated input networks.
failsafe The LVDS outputs can be put into TRI-STATE by use
• 28 lead TSSOP package of the enable pin.
• Conforms to ANSI/TIA/EIA-644 LVDS standard For more details, please refer to the APPLICATION
INFORMATION section of this datasheet.
Connection Diagram
Order Number DS90LV110ATMT
PW0028A Package
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2004–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
DS90LV110AT
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
www.ti.com
Block Diagram
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1)
Supply Voltage (VDD-VSS)−0.3V to +4V
LVCMOS/LVTTL Input Voltage (EN) −0.3V to (VCC + 0.3V)
LVDS Receiver Input Voltage (IN+, IN−)−0.3V to +4V
LVDS Driver Output Voltage (OUT+, OUT−)−0.3V to +4V
Junction Temperature +150°C
Storage Temperature Range −65°C to +150°C
Lead Temperature (Soldering, 4 sec.) +260°C
Maximum Package Power 28 Lead TSSOP 2.115 W
Dissipation at 25°C
Package Derating 28 Lead TSSOP 16.9 mW/°C above +25°C
θJA 28 Lead TSSOP 59.1 °C/W
(4-Layer, 2 oz. Cu, JEDEC) (HBM, 1.5kΩ, 100pF) > 8 kV
ESD Rating: (EIAJ, 0Ω, 200pF) > 250 V
(1) “Absolute Maximum Ratings” are these beyond which the safety of the device cannot be verified. They are not meant to imply that the
device should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation.
Recommended Operating Conditions Min Typ Max Units
Supply Voltage (VDD - VSS) 3.0 3.3 3.6 V
Receiver Input Voltage 0 VDD V
Operating Free Air Temperature -40 +25 +85 °C
2Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
DS90LV110AT
www.ti.com
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol Parameter Conditions Min Typ(1) Max Units
LVCMOS/LVTTL DC SPECIFICATIONS (EN)
VIH High Level Input Voltage 2.0 VDD V
VIL Low Level Input Voltage VSS 0.8 V
IIH High Level Input Current VIN = 3.6V or 2.0V; VDD = 3.6V ±7 ±20 μA
IIL Low Level Input Current VIN = 0V or 0.8V; VDD = 3.6V ±7 ±20 μA
VCL Input Clamp Voltage ICL =−18 mA −0.8 −1.5 V
LVDS OUTPUT DC SPECIFICATIONS (OUT1, OUT2, OUT3, OUT4, OUT5, OUT6, OUT7, OUT8, OUT9, OUT10)
VOD Differential Output Voltage RL= 100Ω250 320 450 mV
RL= 100Ω, VDD = 3.3V, TA= 25°C 260 320 425 mV
ΔVOD Change in VOD between Complimentary Output States 35 |mV|
VOS Offset Voltage (2) 1.125 1.25 1.375 V
ΔVOS Change in VOS between Complimentary Output States 35 |mV|
IOZ Output TRI-STATE Current EN = 0V, ±1 ±10 μA
VOUT = VDD or GND
IOFF Power-Off Leakage Current VDD = 0V; VOUT = 3.6V or GND ±1 ±10 μA
ISA,ISB Output Short Circuit Current VOUT+ OR VOUT−= 0V or VDD 12 24 |mA|
ISAB Both Outputs Shorted (3) VOUT+ = VOUT−6 12 |mA|
LVDS RECEIVER DC SPECIFICATIONS (IN)
VTH Differential Input High Threshold VCM = +0.05V or +1.2V or +3.25V, 0 +100 mV
VDD = 3.3V
VTL Differential Input Low Threshold −100 0 mV
VCMR Common Mode Voltage Range VID = 100mV, VDD = 3.3V 0.05 3.25 V
IIN Input Current VIN = +3.0V, VDD = 3.6V or 0V ±1 ±10 μA
VIN = 0V, VDD = 3.6V or 0V ±1 ±10 μA
SUPPLY CURRENT
ICCD Total Supply Current RL= 100Ω, CL= 5 pF, 200 MHz, 125 160 mA
EN = High
No Load, 200 MHz, EN = High 80 125 mA
ICCZ TRI-STATE Supply Current EN = Low 15 29 mA
(1) All typical are given for VCC = +3.3V and TA= +25°C, unless otherwise stated.
(2) VOS is defined as (VOH + VOL) / 2.
(3) Only one output can be shorted at a time. Don't exceed the package absolute maximum rating.
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: DS90LV110AT
DS90LV110AT
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
www.ti.com
AC Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol Parameter Conditions Min Typ Max Units
TLHT Output Low-to-High Transition Time, 20% to 80%, Figure 4 (1) 390 550 ps
THLT Output High-to-Low Transition Time, 80% to 20%, Figure 4 (1) 390 550 ps
TDJ LVDS Data Jitter, Deterministic (Peak-to- VID = 300mV; PRBS=223-1 data; 145 ps
Peak) (2) VCM = 1.2V at 400 Mbps (NRZ)
TRJ LVDS Clock Jitter, Random (2) VID = 300mV; 2.8 ps
VCM = 1.2V at 200 MHz clock
TPLHD Propagation Low to High Delay, Figure 5 2.2 2.8 3.6 ns
TPHLD Propagation High to Low Delay, Figure 5 2.2 2.8 3.9 ns
TSKEW Pulse Skew |TPLHD - TPHLD|(1) 20 340 ps
TCCS Output Channel-to-Channel Skew, Figure 6 (1) 35 91 ps
TPHZ Disable Time (Active to TRI-STATE) High to Z, Figure 1 3.0 6.0 ns
TPLZ Disable Time (Active to TRI-STATE) Low to Z, Figure 1 1.8 6.0 ns
TPZH Enable Time (TRI-STATE to Active) Z to High, Figure 1 10.0 23.0 ns
TPZL Enable Time (TRI-STATE to Active) Z to Low, Figure 1 7.0 23.0 ns
(1) The parameters are specified by design. The limits are based on statistical analysis of the device performance over PVT (process,
voltage and temperature) range.
(2) The measurement used the following equipment and test setup: HP8133A pattern/pulse generator), 5 feet of RG-142 cable with DUT
test board and HP83480A (digital scope mainframe) with HP83484A (50GHz scope module). The HP8133A with the RG-142 cable
exhibit a TDJ = 26ps and TRJ = 1.3 ps
AC TIMING DIAGRAMS
Figure 1. Output active to TRI-STATE and TRI-STATE to active output time
4Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
DS90LV110AT
www.ti.com
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
Figure 2. LVDS Driver TRI-STATE Circuit
Figure 3. LVDS Output Load
Figure 4. LVDS Output Transition Time
Figure 5. Propagation Delay Low-to-High and High-to-Low
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: DS90LV110AT
DS90LV110AT
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
www.ti.com
Figure 6. Output 1 to 10 Channel-to-Channel Skew
APPLICATION INFORMATION
INPUT FAIL-SAFE
The receiver inputs of the DS90LV110A have internal fail-safe biasing for short, open, and teminated input
conditions.
LVDS INPUTS TERMINATION
The LVDS Receiver input must have a 100Ωtermination resistor placed as close as possible across the input
pins.
UNUSED CONTROL INPUTS
The EN control input pin has internal pull down device. If left open, the 10 outputs will default to TRI-STATE.
EXPANDING THE NUMBER OF OUTPUT PORTS
To expand the number of output ports, more than one DS90LV110A can be used. Total propagation delay
through the devices should be considered to determine the maximum expansion. Adding more devices will
increase the output jitter due to each pass.
PCB LAYOUT AND POWER SYSTEM BYPASS
Circuit board layout and stack-up for the DS90LV110A should be designed to provide noise-free power to the
device. Good layout practice also will separate high frequency or high level inputs and outputs to minimize
unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by
using thin dielectrics (4 to 10 mils) for power/ground sandwiches. This increases the intrinsic capacitance of the
PCB power system which improves power supply filtering, especially at high frequencies, and makes the value
and placement of external bypass capacitors less critical. External bypass capacitors should include both RF
ceramic and tantalum electrolytic types. RF capacitors may use values in the range 0.01 µF to 0.1 µF. Tantalum
capacitors may be in the range 2.2 µF to 10 µF. Voltage rating for tantalum capacitors should be at least 5X the
power supply voltage being used. It is recommended practice to use two vias at each power pin of the
DS90LV110A as well as all RF bypass capacitor terminals. Dual vias reduce the interconnect inductance by up
to half, thereby reducing interconnect inductance and extending the effective frequency range of the bypass
components.
The outer layers of the PCB may be flooded with additional ground plane. These planes will improve shielding
and isolation as well as increase the intrinsic capacitance of the power supply plane system. Naturally, to be
effective, these planes must be tied to the ground supply plane at frequent intervals with vias. Frequent via
placement also improves signal integrity on signal transmission lines by providing short paths for image currents
which reduces signal distortion. The planes should be pulled back from all transmission lines and component
mounting pads a distance equal to the width of the widest transmission line or the thickness of the dielectric
separating the transmission line from the internal power or ground plane(s) whichever is greater. Doing so
minimizes effects on transmission line impedances and reduces unwanted parasitic capacitances at component
mounting pads.
6Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
OUT+
OUT- 50:50:
100: Differential T-Line
DS90LV110A
Receiver
IN+
IN-
100:
LVPECL
Driver
OUT+
OUT-
50:50:
VCC
CML3.3V or CML2.5V
Driver
100: Differential T-Line
DS90LV110A
Receiver
IN+
IN-
100:
OUT+
OUT-
DS90LV110A
Receiver
IN+
IN-
100: Differential T-Line
100:
LVDS
Driver
DS90LV110AT
www.ti.com
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
There are more common practices which should be followed when designing PCBs for LVDS signaling. Please
see Application Note: AN-1108(SNLA008) for additional information.
INPUT INTERFACING
The DS90LV110A accepts differential signals and allow simple AC or DC coupling. With a wide common mode
range, the DS90LV110A can be DC-coupled with all common differential drivers (that is, LVPECL, LVDS, CML).
Figure 7,Figure 8, and Figure 9 illustrate typical DC-coupled interface to common differential drivers.
Figure 7. Typical LVDS Driver DC-Coupled Interface to DS90LV110A Input
Figure 8. Typical CML Driver DC-Coupled Interface to DS90LV110A Input
Figure 9. Typical LVPECL Driver DC-Coupled Interface to DS90LV110A Input
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: DS90LV110AT
OUT+
OUT-
CML or
LVPECL or
LVDS
IN+
IN-
100:
100: Differential T-Line
Differential
Receiver
DS90LV110A
Driver
DS90LV110AT
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
www.ti.com
OUTPUT INTERFACING
The DS90LV110A outputs signals that are compliant to the LVDS standard. Their outputs can be DC-coupled to
most common differential receivers. Figure 10 illustrates typical DC-coupled interface to common differential
receivers and assumes that the receivers have high impedance inputs. While most differential receivers have a
common mode input range that can accommodate LVDS compliant signals, it is recommended to check
respective receiver's data sheet prior to implementing the suggested interface implementation.
Figure 10. Typical DS90LV110A Output DC-Coupled Interface to an LVDS, CML or LVPECL Receiver
DS90LV110A PIN DESCRIPTIONS
Pin Name # of Pin Input/Output Description
IN+ 1 I Non-inverting LVDS input
IN - 1 I Inverting LVDS input
OUT+ 10 O Non-inverting LVDS Output
OUT - 10 O Inverting LVDS Output
EN 1 I This pin has an internal pull-down when left open. A logic low on the
Enable puts all the LVDS outputs into TRI-STATE and reduces the
supply current.
VSS 3 P Ground (all ground pins must be tied to the same supply)
VDD 2 P Power Supply (all power pins must be tied to the same supply)
8Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
DS90LV110AT
www.ti.com
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
MULTI-DROP APPLICATIONS
POINT-TO-POINT DISTRIBUTION APPLICATIONS
For applications operating at data rate greater than 400Mbps, a point-to-point distribution application should be
used. This improves signal quality compared to multi-drop applications due to no stub PCB trace loading. The
only load is a receiver at the far end of the transmission line. Point-to-point distribution applications will have a
wider LVDS bus lines, but data rate can increase well above 400Mbps due to the improved signal quality.
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: DS90LV110AT
DS90LV110AT
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
Output Voltage (VOD) vs. Resistive Load (RL) Peak-to-Peak Output Jitter at VCM = +0.4V vs. VID
Peak-to-Peak Output Jitter at VCM = +1.2V vs. VID Peak-to-Peak Output Jitter at VCM = +2.9V vs. VID
10 Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
DS90LV110AT
www.ti.com
SNOSAC2J –AUGUST 2004–REVISED APRIL 2013
REVISION HISTORY
Changes from Revision I (April 2013) to Revision J Page
• Changed layout of National Data Sheet to TI format ............................................................................................................ 1
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: DS90LV110AT
PACKAGE OPTION ADDENDUM
www.ti.com 13-Sep-2014
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
DS90LV110ATMT NRND TSSOP PW 28 48 TBD Call TI Call TI -40 to 85 DS90LV
110ATMT
DS90LV110ATMT/NOPB ACTIVE TSSOP PW 28 48 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 85 DS90LV
110ATMT
DS90LV110ATMTX/NOPB ACTIVE TSSOP PW 28 2500 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 85 DS90LV
110ATMT
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 13-Sep-2014
Addendum-Page 2
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
DS90LV110ATMTX/NOPB TSSOP PW 28 2500 330.0 16.4 6.8 10.2 1.6 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
DS90LV110ATMTX/NOPB TSSOP PW 28 2500 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
