9 Relay I/O Block G7TC Reduces Wiring within the Control Panel and Reduces Installation Time 1 Compact 16-pt models: 182 W l 85 D l 68 H mm; 8-pt block width is 102 mm 1 Can be connected to the PLC with a connecting cable and a snap-in connector 1 Equipped with surge suppressor circuit eo and LED indicators 1 Mounts easily on a DIN rail Ordering Information 3 G7TC RELAY I/O BLOCKS Relay I/O Blocks include the I/O Base with G7T Relays installed. I/O classification I/O points Internal I/O circuit common Rated coil voltage Input p 16 NPN (OE common)) 24 VDC NPN (OE common)) 110/120 VAC Part number G7TC-ID16 DC24V G7TC-ID16-5 DC24V (See Note 1) G7TC-IA16 AC110/120V G7TC-IA16-5 AC100/110V (See Note 1) Output p (S Note (See N t 2) 16 8 220/240 VAC G7TC-IA16 AC220/240V 12 VDC G7TC-OC16 DC12V 24 VDC G7TC-OC16 DC24V PNP (OE common) 24 VDC G7TC-OC16-1 DC24V NPN ( ( common)) 12 VDC G7TC-OC08 DC12V 24 VDC G7TC-OC08 DC24V 24 VDC G7TC-OC08-1 DC24V NPN ( ( common)) PNP (OE common) Note: 1. The "-5" Block is for use with DRT1-ID16X DeviceNet Remote Adapter. 2. Output relays are rated up to 250 VAC. See "Specifications" for specific relay ratings. 3 P7TF BLOCK BASES AND RELAYS Combine Relays and P7TF Block Bases to match your application requirements. Use the table below to configure Relay Blocks. p I/O points Part number Internal I/O circuit i it Block Base 16 inputs (AC coil) il) NPN ((-- common)) P7TF-IS16 AC110/120V 16 inputs (DC coil) NPN (-- common) 1A G7T-1122S AC110/120 or Solid State Relay 25 mA G3TA-IAZR02S AC100/240V G7T-1122S AC200/220V P7TF-IS16 DC24V 1A G7T-1122S DC24V 25 mA G3TA-IDZR02S DC5-24V P7TF-OS16 DC12V 5A G7T-1112S DC12V 2A G3TA-ODX02S 12VDC P7TF-OS16 DC24V 5A G7T-1112S DC24V 2A G3TA-ODX02S DC24V or PNP (-- common) P7TF-OS16-1 DC24V 5A G7T-1112S DC24V 1A G3TA-OD201S DC24V NPN (+ common) P7TF-OS08 DC12V 5A G7T-1112S DC12V 2A G3TA-ODX02S 12VDC NPN (+ common) P7TF-OS08 DC24V 5A G7T-1112S DC24V 2A G3TA-ODX02S DC24V or PNP (-- common) P7TF-OS08-1 DC24V 5A G7T-1112S DC24V 1A G3TA-OD201S DC24V 16 outputs NPN (+ common) (DC coil) il) NPN (+ common) 8 outputs (DC coil) il) I/O Relay G7TC G7TC - G7TC- - P7TF- 1 2 3 4 1 2 3 1. Input/Output Classification I : For input O : For output 2. Type of I/O Signal A : AC coil type for input relays mounted D : DC coil type for input relays mounted C : Contact output 3. Number of I/O Points 16: 16 points 08: 8 points (for output only) 4. Internal I/O Circuit Common Blank:NPN (+) common 1: PNP (--) common 5. Block for use with DeviceNet 4 1. Input/Output Classification I : For input O : For output 2. Type of I/O Signal S : Socket for input or output relays 3. Number of I/O Points 16: 16 points 08: 8 points (for output only) 4. Internal I/O Circuit Common Blank: NPN (+) common 1: PNP (--) common 3 CONNECTOR CABLES Item Length Connecting g cable with ith crimp i type hooks Connecting g cable with ith connector t on both ends Part number 1.0 m (3.28 ft) G79-Y100C 1.5 m (4.92 ft) G79-Y150C 2.0 m (6.56 ft) G79-Y200C 3.0 m (9.84 ft) G79-Y300C 5.0 m (16.40 ft) G79-Y500C 1.0 m (3.28 ft) G79-100C 1.5 m (4.92 ft) G79-150C 2.0 m (6.56 ft) G79-200C 3.0 m (9.84 ft) G79-300C 5.0 m (16.40 ft) G79-500C 3 ACCESSORIES (ORDER SEPARATELY) Description Part number Single I/O socket for SPST and SPDT Relays P7TF-05 Indicator module for AC (with varistor surge suppression) P70A Indicator module for DC (with diode surge suppression) P70D Output short circuit protection module G77-5 Shorting bar G78-04 Finger protection cover for 16-pt blocks G78-E Specifications 3 RATINGS: G7T RELAYS Coil Data (Common to Input/Output per Relay) Rated voltage ( ) (V) Rated current (mA) 50 Hz 60 Hz Coil es sta ce resistance (S Note (See N 1) Must operate Must release Maximum voltage Percent of rated voltage Power consumption per Relay per 16 Relays 80% max. 30% min. 110% 0.7 VA 11 VA 42 13,000 48,300 290 80% max. 10% min. 110% 0.5 W 8W 21 1,150 80% max. 10% min. 110% 0.5 W 8W AC 110/120 220/240 7.5/-- 3.7/-- DC 12 DC 24 6.4/7.0 3.2/3.5 Note: 1. The rated current and coil resistance are measured at a coil temperature of +23C with a tolerance of +15%/--20% for AC rated current and 15% for coil resistance. 2. Approx. 4 mA flows into each LED indicator. To calculate the power supply capacity, add the current value of each indicator. 2 G7TC G7TC Contact Data (G7T I/O Relay) Classification For input For output Load type Resistive load (cos=1) Carry current 1A Switching voltage 250 VAC, 125 VDC Switching current 1A 0.5 A 5A 2A Switching power DC 24 W DC 12 W DC 120 W AC 440 VA DC 48 W AC 220 VA Min. permissible load 100 A at 1 V Electrical life 10,000,000 operations (at 10 mA) 50,000 operations (at 1 A) Mechanical life 50,000,000 operations Inductive load (cos=0.4 L/R=7 ms) Resistive load (cos=1) Inductive load (cos=0.4 L/R=7 ms) 5A 10 mA at 5 V 2,500,000 operations (at 10 mA) 20,000 operations (at 1 A) 1,000,000 operations (under rated load) 3 CHARACTERISTICS: G7T RELAYS Model G7TC-IA16 (Input, AC coil) G7TC-ID16 (Input, DC coil) G7TC-OC16 (-1) (Output, DC coil) LED color Red Green Green Case color Transparent red Transparent green Transparent Contact resistance 50 m max. Operate time 15 ms max. Release time Max. operating p g f frequency G7TC-OC08 (-1) (Output, DC coil) 15 ms max. Mechanical limit 18,000 operations/hour At rated load 1,800 operations/hour Insulation resistance 100 M at 500 VDC Dielectric strength t th Between coil and contact 2,000 VAC, 50/60 Hz for 1 minute Between same polarity contacts 1,000 VAC, 50/60 Hz for 1 minute Between paired connectors 250 VAC, 50/60 Hz for 1 minute Malfunction vibration 10 to 55 Hz with 1.0-mm double amplitude Malfunction shock 200 m/s2 Noise immunity Noise level: 1.5 kV; pulse width: 100 ns to 1 s Rated voltage between positive and negative terminal blocks Rated voltage of controller's (PLC or other) input circuit 24 VDC 5% Rated current between positive and negative terminal blocks Input circuit current of controller (PLC or other) x number of ON points 24 VDC: 25 mA x number of ON points Cable length g To controller 5 m max. (reference value) To I/O devices 50 m max. (reference value, for 2-mm2 CVV cable) Ambient operating temperature 0C to 55C (32F to 131F) Ambient operating humidity 35% to 85% I/O terminal tightening torque 8 to 12 kg : cm Coil surge absorber Variable resistor Diode (1 A, 400 V) Weight Approx. 640 g Approx. 630 g Dependent on load Approx. 670 g Approx. 350 g 3 G7TC G7TC UL and CSA Standards Standard G7TC I/O Blocks, except for the G7TC-OC16-1 and the G7TC-OC08(-1), have met UL and CSA standards (UL file no. E41643; CSA file no. LR31928). Note that the following UL- and CSA-qualifying ratings differ from the performance characteristics of the individual models: Part number Coil ratings Contact ratings G7TC-ID16, G7TC-IA16 10 mA/point, 24 VDC 250 VAC max. G7TC-OC16 Coil drive current, 24 VDC Inductive load: 10 A, 250 VAC Resistive load: 10 A, 30 VDC Rated horsepower: 1/2 HP, 240 VAC 3 RATINGS: G3TA SOLID STATE RELAYS Input Relay Coil Data Part number Rated voltage Input current Operating p g voltage lt G3TA-IAZR02S AC100/240V 100 to 240 VAC 80 to 264 VDC G3TA-IDZR02S DC5-24V 5 to 24 VDC 4 to 32 VDC Voltage level Must operate voltage 5 mA max. Must release voltage 80 VAC max. 10 VAC min. 4 VDC max. 1 VDC min. Contact Data Part number G3TA-IAZR02S AC100/240V Logic level supply voltage Output breakdown voltage 4 to 32 VDC Output current 32 VDC max. 25 mA max. Output current (load current) 0.1 to 25 mA G3TA-IDZR02S DC5-24V Output Relay Coil Data Part number Rated voltage Operating p g voltage lt Voltage level Input p iimpedance d Must operate voltage G3TA-OA202SZ DC12V 12 VDC 9.6 to 13.2 VDC 0.9 k20% 9.6 VDC max. G3TA-OA202SZ DC24V 24 VDC 19.2 to 26.4 VDC 1.7 k20% 19.2 VDC max. G3TA-ODX02S DC24V 12 VDC 9.6 to 13.2 VDC 3.5 k20% 9.6 VDC max. 24 VDC 19.2 to 26.4 VDC 6.5 k20% 19.2 VDC max. 24 VDC 19.2 to 26.4 VDC 6.4 k20% 19.2 VDC max. G3TA-OD201S DC24V Must release voltage 2 VDC min. Contact Data Part number Applicable load Rated load voltage Load voltage G3TA-OA202SZ 100 to 240 VAC 75 to 264 VAC G3TA-OA202SL 100 to 240 VAC 75 to 264 VAC G3TA-ODX02S 5 to 48 VDC G3TA-OD201S 48 to 200 VDC Inrush current 0.05 to 2 A 30 A (60 Hz, 1 cycle) 4 to 60 VDC 0.01 to 2 A 12 A (10 ms) 40 to 200 VDC 0.01 to 1 A 6 A (10 ms) Note: The minimum current value is measured at 10C min. 4 Load current (See Note) G7TC G7TC 3 CHARACTERISTICS: G3TA SOLID STATE RELAYS Input Relay Item G3TA-IAZR02S G3TA-IDZR02S Operate time 20 ms max. 0.5 ms max. Release time 20 ms max. 0.5 ms max. Output ON voltage drop 1.6 V max. Leakage current 5 A max. Insulation resistance 100 M min. at 500 VDC Dielectric strength 4,000 VAC, 50/60 Hz for 1 min between input and output Vibration resistance Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Shock resistance Malfunction: 1,000 m/s2 (approx. 100G) Ambient temperature Operating: --30C to 80C (--22F to 176F) with no icing or condensation Storage: --30C to 100C (--22F to 212F) with no icing or condensation Ambient humidity Operating: 45% to 85% Approved standards UL508 file No. E64562/CSA C22.2 (No. 0, No. 14) file No. LR35535 Weight Approx. 16 g Output Relay Item G3TA-OA202SZ G3TA-ODX02S G3TA-OD201S Operate time 1/2 of load power source cycle + 1 ms max. 0.5 ms max. 2 ms max. Release time 1/2 of load power source cycle + 1 ms max. 2 ms max. 2 ms max. Output ON voltage drop 1.6 V max. Leakage current 5 mA max. at 200 VAC Insulation resistance 100 M min. at 500 VDC Dielectric strength 4,000 VAC, 50/60 Hz for 1 min between input and output Vibration resistance Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Shock resistance Malfunction: 1,000 m/s2 (approx. 100G) Ambient temperature Operating: --30C to 80C (--22F to 176F) with no icing or condensation Storage: --30C to 100C (--22F to 212F) with no icing or condensation Ambient humidity Operating: 45% to 85% Approved standards UL508 file No. E64562, CSA C22.2 (No. 14) file No. LR3553 Weight Approx. 23 g 2.5 V max. 1 mA max. 3 MIXING G3TA WITH G7T RELAYS IN THE SAME I/O BLOCK With up to four G3TA SSRs mounted before G7T Relays, 2-A loads can be switched. G3TA G7T With G3TA SSRs mounted before every other G7T Relays, 2-A loads can be switched. G3TA G7T 5 G7TC G7TC Engineering Data 3 G7T RELAYS 3 G3TA SOLID STATE RELAYS Load Current vs. Ambient Temperature Characteristics Single-point mounting 16-point mounting G3TA-OD201S Load current (A) Load current (A) G3TA-OA202SZ/OA202SL/ODX02S Single-point mounting 16-point mounting Ambient temperature (C) Ambient temperature (C) Inrush Current Non-repetitive (Keep the inrush current to half the rated value if it occurs repetitively.) Energizing time (ms) 6 G3TA-OD201S Inrush current (A. Peak) G3TA-ODX02S Inrush current (A. Peak) Inrush current (A. Peak) G3TA-OA202SZ Energizing time (ms) Energizing time (ms) G7TC G7TC Operation 3 G3TA SOLID STATE RELAYS Circuit Configuration Type AC output DC output AC input Part number Case color G3TA-OA202SZ (with zero cross function) G3TA-OA202SL (without zero cross function) Black G3TA-ODX02S G3TA-OD201S Black G3TA-IAZR02S Red Indicator Circuit Yes Constant-current circuit Zero cross circuit Constant-current circuit Amplification circuit Yes Yes Rectification circuit DC input G3TA-IDZR02S Drive circuit Green Amplification circuit Constant-current circuit Yes G3TA-IDZR02SM No Amplification circuit Constant-current circuit External Connections (Bottom View) G3TA-IAZR02S G3TA-IDZR02S/IDZR02SM Output + 3 Output 5 -4 + 3 5 -4 1 G3TA-OA G3TA-OD Load power supply Load power supply Load Load -- 3 1 5 4 + 1 + 3 -- -- 5 + 1 4 7 G7TC G7TC Dimensions Unit: mm (inch) 3 G7TC RELAY I/O BLOCKS I/O Block for NPN Input (OE common) G7TC-ID16 G7TC-IA16 182 (7.17) 68 (2.68) 85 (3.35) Terminal Arrangement/Internal Connection G7TC-ID16 (-5) (See Note) Note: When the product has a "-5" at the end of the part number, connector pin number 9 and 19 are negative and connector number 10 and 20 are positive. 8 G7TC G7TC G7TC-IA16 (-5) (See Note) Note: When the product has a "-5" at the end of the part number, connector pin number 9 and 19 are negative and connector pin number 10 and 20 are positive. I/O Block for Output G7TC-OC16 (NPN output/ common) G7TC-OC16-1 (PNP output/OE common) G7TC-OC8 (NPN output/ common) G7TC-OC8-1 (PNP output/OE common) 182 (7.17) 16 pts 102 (4.02) 8 pts 68 (2.68) 85 (3.35) 9 G7TC G7TC Terminal Arrangement/Internal Connection G7TC-OC16 A controller with an NPN transistor, common output can be connected to the G7TC-OC16. G7TC-OC16-1 (PNP output/OE OE common) A controller with a PNP transistor, common output can be connected to the G7TC-OC16-1. Do not connect the G71 Remote Interface to the G7TC-OC16-1. Due to the difference in polarity, the G71 will be damaged if the G7TC-OC16-1 and the G71 are connected to each other. Use the G7TC-OC16 (NPN output/ common) instead, to connect to the G71. Terminal Arrangement/Internal Connection 10 G7TC G7TC G7TC-OC08 A controller with an NPN transistor, common output can be connected to the G7TC-OC08. G7TC-OC08-1 (PNP output/OE OE common) A controller with a PNP transistor, common output can be connected to the G7TC-OC08-1. Do not connect the G7TC-OC08-1 with the G71. Due to the difference in polarity, the G71 will be damaged if the G7TC-OC08-1 and the G71 are connected to each other. Use the G7TC-OC08 (NPN output/ common) instead, to connect to the G71. Connector Pin Configuration Top View Note: Pin numbers are indicated for convenience. The ? mark can be used to determine orientation. 11 G7TC G7TC 3 G7T RELAY Unit: mm (inch) 10 max. (0.39) SPST-NO Type G7T-1122S (for input) G7T-1112S (for output) Terminal Arrangement/ Internal Connections (Bottom View) 32 max. 39 max. (1.54) 15 1.6 2.4 Four 1-dia. holes 0.5 10 max. (0.39) 3.15 (0.12) 4 (0.16) 29 max. 33.5 max. (1.32) SPST-NC Type G7T-1012S (for output) 10 max. (0.39) Terminal Arrangement/ Internal Connections (Bottom View) 32 max. 39 max. (1.54) 15 1.6 2.4 0.5 10 max. (0.39) Four 1-dia. holes 4 (0.16) 29 max. 33.5 max. (1.32) 3 G3TA SOLID STATE RELAYS 35.5 max (1.40) 28.4 10 max. (0.39) 31.7 39 max. (1.54) 24 7.1 7.5 12 9 6 3.15 (0.12) G7TC G7TC Unit: mm (inch) 3 P7TF BLOCK BASES For Input (NPN, OE Common) P7TF-IS16 182 (7.17) 68 (2.68) M3.5 85 (3.35) 26 8 +0.2 35.3 0 34 21 10 32.5 For Output (NPN, Common) P7TF-OS16 68 (2.68) 182 (7.17) M3.5 85 (3.35) 8 10 For Output (PNP, OE Common) P7TF-OS08 +0.2 35.3 0 21 32.5 68 (2.68) 102 (4.02) M3.5 85 (3.35) 8 10 +0.2 35.3 0 21 32.5 P7TF-05 19 max. (0.75) Five, M3.5 x 8 Square washer faced screw 71.5 max. (2.81) 59 max. (2.32) 13 G7TC G7TC G7TC Internal I/O Circuit Common NPN Output PLC PNP Output (Output Only) Input G7TC PLC G7TC PLC G7TC Accessories (Order Separately) 3 G79 CONNECTING CABLES G79 Connecting Cable with Crimp-type Hooks Use these convenient Cables to connect relay I/O Blocks to devices equipped with screw terminals. Power line capacity must be within 50 mA per I/O point. Always check driver capacity and I/O relay power consumption when using an Output Block. Hoods are labeled with corresponding connector pin numbers. Connect hooks 9 and 19 and hooks 10 and 20 together when using the G7TC-OC08. Length (c) Part number 1,000 mm G79-Y100C 1,500 mm G79-Y150C 2,000 mm G79-Y200C 3,000 mm G79-Y300C 5,000 mm G79-Y500C G79 Connecting Cable with One-to-One Connector This Cable is convenient for connecting a Relay I/O Block to a single device equipped with one connector socket. Length (c) Part number 1,000 mm G79-100C 1,500 mm G79-150C 2,000 mm G79-200C 3,000 mm G79-300C 5,000 mm G79-500C 14 G7TC G7TC 3 G7TC TO PLC MODULE CONNECTION OPTIONS One-to-One Connections: (16 Points per Cable) The connecting cables with crimp hooks allow G7TC and P7TF blocks to be used with PLCs from all manufacturers. Relay block Omron PLC module Connection method to PLC Connecting cable 3G2A5-ID213 (16 pts) 3G2A5-IM211 (16 pts) C200H-ID212 (16 pts) C200H-IM212 (16 pts) CQM1-ID212 (16 pts) Crimp hooks G79-Y_ _ _ C C500-MD211CN (input side only) C200H-MD215 (input side only) C200H-ID215 (32 pts) One-to-one connector G79-_ _ _ C G79-_ _ _ C (2) 3G2A5-OC221 (16 pts) 3G2A5-OC223 (16 pts) 3G2A5-OD215 (16 pts) 3G2A5-OD411 (16 pts) C200H-OC225 (16 pts) C200H-OD212 (16 pts) CQM1-OC222 (16 pts) CQM1-OD212 (16 pts) Crimp hooks G79-Y_ _ _ C C500-OD415CN (16 pts) C500-MD211CN (output side only) C200H-MD115 (output side only) C200H-MD215 (output side only) C200H-OD215 (16 pts) One-to-one connector G79-_ _ _ C Inputs G7TC-1A16 G7TC-ID16 P7TF-IS16 Outputs G7TC-OC16 P7TF-OS16 One-to-Two Connections: (Cable Splits One Connector to Two Relay Blocks) Relay block PLC module Connection method to PLC Connecting cable 3G2A5-ID219 (64 pts) C500-ID114 (64 pts) C500-ID218CN (32 pts) C200H-ID216 (32 pts) C200H-ID217 (64 pts) CQM1-ID213 (32 pts) Special cable that splits a single connector at the PLC to two at the relay blocks G79-I _ _ _C _ _ _ (2 are required for 64-pt modules) 3G2A5-OD213 (64 pts) C500-OD218 (32 pts) C500-OD415CN (32 pts) C200H-OD218 (32 pts) CQM1-OD219 (64 pts) Special cable that splits a single connector at the PLC to two at the relay blocks G79-O _ _ _C _ _ _ (2 are required for 64-pt modules) Inputs G7TC-1A16 G7TC-ID16 P7TF-IS16 Outputs G7TC-OC16 P7TF-OS16 High-density Connections (Cable Splits One Connector to Three Relay Blocks) Relay block PLC module Connection method to PLC Connecting cable CS1W-ID291 (96 pts) CS1W-MD291 (48 pts, input side only) Special cable that splits a single connector at the PLC to three at the relay blocks G79- _ _ _C -_ _ _- _ _ _ (2 are required for 96-pt modules) CS1W-OD219 (96 pts) CS1W-MD291 (48 pts, output side only) Special cable that splits a single connector at the PLC to three at the relay blocks G79- _ _ _C -_ _ _- _ _ _ (2 are required for 96-pt modules) Inputs G7TC-IA16 G7TC-ID16 P7TF-IS16 Outputs G7TC-OC16 P7TF-OS16 15 G7TC G7TC Unit: mm (inch) 3 SHORTING BAR G78-04 Use this piece for short-circuiting across terminals. Max. current flow: 20 A Item Shorting bar 4.5 Part number 13.3 12.5 (0.52) G78-04 R1.8 10 0.05 10 0.05 10 0.05 37.8 (1.49) R1.0 3 FINGER PROTECTION COVER FOR G7TC OR P7TF (MEETS VDE 0106 PART 100) G78-E This cover is for 16-point relay blocks only and cannot be used with an 8-point relay block. 178 (7.01) 6.30 dia. 14.5 12.5 27 (1.06) 12.5 10 10 10 12.5 6 26.35 (1.04) 13.85 7.5 16 2.5 (0.10) G7TC G7TC I/O Block Details 3 INPUT BLOCKS G7TC-ID16 G7TC-IA16 Supply power to terminals 0 through 15 and C0 through C15 according to the voltage specifications of the I/O Relays and I/O Block. Do not reverse positive and negative terminals on the DC Input Block (0 through 15 are positive; C0 through C15, negative). Shorting bars are available. Supply to the power terminal (positive and negative) the rated voltage of the controller's input circuits (24, 12). Use a low-noise power source. 3 OUTPUT BLOCKS G7TC-OC16(-1) G7TC-OC08(-1) Supply power to contact output terminals 0 through 15 and C0 through C15 according to the requirements of the loads. A 4 terminal Shorting Bar is available. Supply to the power terminals (positive and negative) power both for driving the relays and for controller output transistors. Match the controller and I/O block voltage specifications. Use a low-noise power source. Output Block model G7TC-OC08 does not have terminals 8 through 15 and C8 through C15. Although a 20-pin connector is used, pins 11 through 18 are not connected. 17 G7TC G7TC To Increase the Number of Outputs Use sockets (order separately) to increase the number of outputs or to use SPDT I/O Relays on the G7TC. 3 EXTERNAL CONNECTION EXAMPLE The following is an application example for the P7TF-05 using a SPDT Relay on a terminal of the G7TC-16(-1). *Use the G77-S Output Short-Circuit Module in place of the G7T I/O Relay. With the G77-S voltage output is available between terminals 15 and C15. The maximum current is determined according to the controller. Note: If more than one G77-S Output Short-Circuit Module is employed, the voltage output of the terminals on the G7TC is as follows: G7TC-OS16: The positive side (the lower row) connects to the common line internally. G7TC-OS16-1: The negative side (the upper row) connects to the common line internally. 3 P7TF-05 SOCKET The G7T Relays (SPST-NO, SPST-NC, and SPDT types) and the G3TA I/O Relays can be mounted on the P7TF-05 Socket. To add SPDT relays (G7T-112S) to a G7TC or P7TF installation, use the G77-S Output Short-Circuit Module and the P7TF-05 Socket. Specifications Contact resistance 10 m max. Dielectric strength 2,000 VAC for 1 minute Insulation resistance 100 M at 500 V Vibration 10 to 55 Hz, 1.0 mm double amplitude Shock 200 m/s2 Ambient temperature Operating: 0 to 55C (32F to 131F) Humidity 35% to 85% Weight Approx. 28 g 18 G7TC G7TC Unit: mm (inch) Dimensions Internal Connections (Top View) 19 max. (0.75) 71.5 max. (2.81) 9 4 19.5 59 max. (2.32) Note: Terminal 1 is positive when the I/O SSR is employed. 3 P70 INDICATOR MODULE (WITH SURGE SUPPRESSING FUNCTION) Remove the transparent style strip of the P7TF-05 socket and mount this module and it will function as an operation indicator with the surge suppression. Part number Applicable relay coil voltage For AC relayy P70A For DC relay P70D 110/120 VAC Remarks Surge g suppressing g system y with varistor 220/240 VAC 12/24 VDC Surge suppressing system with diode Note: 1. Order the indicator module suitable for the relay coil voltage. 2. The indicator module for DC relays has a multiple power supply common to both 12 and 24 VDC. Dimensions 29.5 max. (1.16) 8.5 max. (0.33) 32.5 max. 39 max. (1.54) Internal Connection 1.6 0.5 20 2.6 Two 1 dia. holes 19 G7TC G7TC Unit: mm (inch) 3 G77-S OUTPUT SHORT-CIRCUIT MODULE The output of the I/O Block can be obtained without relays through the G77-S Output Short-Circuit Module. Note that the G77-S Output Short-Circuit Module is not available for inputs. 10 max. (0.39) 32 max. 39 max. (1.54) 1.6 Terminal Arrangement/Internal Connections (Bottom View) 15 3.15 (0.12) 0.5 2.4 4 10 max. (0.39) 29 max. 33.5 max. (1.32) Precautions 3 CORRECT INSTALLATION I/O Blocks are color coded, as shown below, according to input/output and AC/DC specifications. I/O Terminal label I/O Terminal indicators Output Block (DC) Yellow Green Transparent Input Bl k Block DC Red Green Green AC Red Red Red Block type I/O Relay case Rails are generally used to mount Relay I/O Blocks. For screw mounting, a 210-mm DIN rail is available that can be used as an adapter in combination with End Plates (PFP-M, two required). 3 USING A SHORTING BAR A Shorting Bar is provided to connect four terminals. The current capacity of the shorting bar is 20 A. As long as this current capacity is not exceeded, the shorting bar can be used in combination as shown at the right to connect more than four terminals. Both Input and Output Blocks do not have internal power supplies. For an Output Block, supply the relay drive power to the positive and negative terminals (either 12 or 24 VDC). Loads (terminal contacts 0 through 15) must also be supplied with appropriate power. For an Input Block, supply power to the positive and negative terminals for the input signals to the controller. The same Connecting Cable, G79-Y, is used for the G7TC-OC08 eight-point Output Block as for other I/O Blocks; leave 8 points unconnected. LEDs indicate the presence or absence of signals. Use the display lever inside each relay for fault diagnosis. (Some relays do not have this lever, depending on the specifications.) Each relay must be pressed down until its hold-down hooks engage completely. Heating or malfunction can result if relays are not mounted properly. Unlabeled terminals are not electrically connected. Use these for repeater terminals. LED positions and relay orientation differ between Input and Output Blocks. This is to aid in differentiating Input Blocks from Output Blocks and in following signal flow. DC I/O Blocks have positive and negative terminals, with the positive terminals normally on the top of the I/O Block. Reversing positive and negative terminals will prevent operation. 20 Operational errors can result if connectors are connected or removed with power supplied to the I/O Block. G7TC G7TC NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4. 9 OMRON ELECTRONICS, INC. OMRON CANADA, INC. One East Commerce Drive Schaumburg, IL 60173 885 Milner Avenue Scarborough, Ontario M1B 5V8 1-800-55-OMRON 416-286-6465 Cat. No. GC RIO-1 04/00 Specifications subject to change without notice. Printed in U.S.A.