New Product Launch Package Soft SMD Grounding Contacts June, 2013 1 New Product Launch Package Description: Laird Technologies' SMD (Surface Mount Device) Grounding Contact is a conductive contacts used for circuit grounding of SMT (Surface Mount Technology) devices. These contacts are designed to be solder reflow compatible, and are suitable for automatic processing Launch Package Number LT201302 Product Composition: Available Dimensions: Design Considerations: Hour Glass Narrow profile under compression Advantage Availability in smaller profiles 3 Launch Package Number LT201302 Rectangular Advantage Stability Advantage Aspect ratio Advantage Tight Board Density Cost Advantage Advantage Part Number Structures: Example: "SLG-060-040-100-TR" rectangle, 6mm width, 4mm height, 10mm length in Tape & Reel Example: "SLH-080-100-070-TR" hourglass, 8mm width, 10mm height, 7mm length in Tape & Reel 4 Launch Package Number LT201302 Advantages: 1. 2. 3. 4. 5. 6. 7. 8. 9. 5 Reflow Soldering using SMT processes. (Peak Temp 260C Max) Tape-and-Reel packaging for automatic processing. Multiple solder reflow operations, up to 3 times. Excellent compressibility and Compression Set. Excellent electrical conductivity at low pressure. Board Level grounding contacts without tooling. Repairable Cost competitive to Metal Contacts Covered by Patent (Pending) Launch Package Number LT201302 Technical Data From Specification Sheet 6 7 Launch Package Number LT201301 Technical Data From MSDS 8 LT-MSDS-046-C SMD grounding contacts 2013/06/07 MATERIAL SAFETY DATA SHEET SECTION 1 SUBSTANCE/PREPARATION AND COMPANY NAME Product Name: Soft SMD Grounding Contacts Manufacturer: Laird Technologies Division: International Operation Address: 3481 Rider Trail South, St. Louis MO 63045 Emergency Phone: +1-866-928-8181 (Global) or +86-755-2714-1166 (China) SECTION 2 COMPOSITION/INFORMATION ON INGREDIENTS SECTION 3 HAZARDS IDENTIFICATION Appearance and odor: no odor. Following our present state of knowledge this product is not classified as a hazardous substance. SECTION 4 FIRST AID MEASURES The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Inhalation: Not applicable under normal conditions of use. Ingestion: Not specifically applicable Skin: Not specifically applicable Eyes: Not specifically applicable In any case, seek medical advice ASAP. SECTION 5 FIRE-FIGHTING MEASURES Extinguishing Media: Carbon dioxide gas, sand/earth, regular foam, water Special Fire Fighting Procedures: Wear self-contained breathing apparatus and protective clothing to prevent contact with skins and eyes. 9 Unusual Fire Hazards: Any chemical can be forced to burn by continuous application or intense heat. Launch Package Number LT201301 SECTION 6 ACCIDENTAL RELEASE MEASURES Leaks and Spills: Sweep up and place into specified containers for disposal. Large Spillage: Incinerate or landfill in accordance with local state regulation Protective Equipment: None SECTION 7 HANDLING AND STORAGE Handling: Does not require any specific handling procedure. Storage: Keep away from heat, sparks, and open flame. SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION Eye Protection: This material does not cause significant eye irritation of eye toxicity requiring special protection. Use good industrial practice to avoid eye contact Skin Protection: Avoid skin contact. Consult glove manufacturer to determine appropriate type of glove for given application. Wash contaminated skin promptly. Wash thoroughly after handling. Respiratory protection: Not needed SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES Boling Point: N/A Specific Gravity: N/A Melting Point: N/A PH: N/A Solubility in Water: Non-soluble Decomposition Temperature: N/A Appearance and Odor: Rubber profile, odorless Additional Comments: It should be noted that these physical and chemical data are based on typical measurements obtained from tests on the material, but not intended for use as guaranteed analysis of any specific lot or as specifications for the product. SECTION 10 STABILITY AND REACTIVITY Stability: Stable. Conditions to avoid: Open flame, heat, spark and any other sources of ignition. Incompatibility (Materials to Avoid): None known. Hazardous Decomposition Product: Combustion will produce CO2, CO, or other chemical. Hazardous Polymerization: Will not occur. 10 SECTION 11 TOXICOLOGICAL INFORMATION Launch Package Number LT201301 Inhalation: Processing vapor may be an irritant. Ingestion: Not known Skin: Wash immediately with plenty of water if symptoms appear. Eyes: Sharp off-cuts may cause eye damage. Long Term Exposure: N/A SECTION 12 ECOLOGICAL INFORMATION On the basis of data concerning degradation and bio accumulation, no environmental harm can be ruled out. SECTION 13 DISPOSAL CONSIDERATIONS The product can be land filled. Disposal should be in accordance with local & state regulation SECTION 14 TRANSPORT INFORMATION Remarks: Not dangerous by any mode of international transport. Class: Not dangerous SECTION 15 REGULATORY INFORMATION Hazardous Symbol: None Risk Phrase: May cause sensitization by long-term skin contact. Safety Phrase: Handle in good industrial hygiene practice. SECTION 16 OTHER INFORMATION Use: For general EMI shielding and grounding. The information given in this Safety Data Sheet is based on our knowledge of the product at the time of publication and is given in good faith. The attention of the user is drawn to the possible risks incurred by using the product for any other purpose than that for which it was intended. It is the sole responsibility of the user to take all precautions in handling the product. We cannot guarantee that the risks referred to above are the only 11 risks present. The final choice of the application of a product is thus the sole responsibility of the user Launch Package Number LT201301 Sales Person / Presenter Information Email and contact info. 12