1.0mm
3.2mm
17mm
Metal fittings
Actuator
0.5 mm Pitch, 1.0 mm above the board Top and Top/Bottom Contact, Back-Flip
actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
FH34(S)Series
1
2013.11w
■Features
1. Low-profile
With the 1.0 mm above the board and width of 3.8 mm the
connectors are used in space saving applications.
2. Increased FPC/FFC retention
As compared with existing similar construction connectors:
* In horizontal direction: Approximately 2.6 times
* In vertical direction: Approximately 2 times
3. Unique Back-Flip rotating actuator
The rotating actuator opens from the back of the connector,
assuring reliable electrical and mechanical connection.
4.
Easy FPC insertion and reliable electrical
connection
Proven Flip Lock actuator allows easy insertion of FPC and
provides a tactile sensation when fully closed, confirming
complete electrical and mechanical connection.
5. Delivered with the actuator open
FPC/FPC can be immediately inserted without the need
for the opening of the actuator.
6. Accepts standard FPC thickness
0.3mm thick standard Flexible Printed Circuit (FPC) can
be used. This is the only ultra-low profile ZIF connector
using standard FPC.
7. Compatible with existing connectors.
FPC/FFC and PCB mounting patterns are the same as for
the FH19SC Series (bottom contact), allowing the use of
both connectors for interconnections between two boards or
replacement of the connectors.
8. Conductive traces on the PCB can run
under the connector
No exposed contacts on the bottom of the connector.
9. Board placement with automatic equipment
Flat upper surface and tape and reel packaging facilitate
vacuum pick-up and placement.
Standard reel packaging contains 5000 connectors.
10.Halogen-free*
*As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm
maximum
Increased FPC/FFC holding force
Compatible with existing connectors.(FH19SC SERIES)
Easy FPC/FFC insertion
17mm
FPC / FFC
Back opening rotating
Top contacts
All four
sides are
chamfered.
Ready to insert FPC/FFC
FPC/FFC inserted and retained.
Completed electrical and mechanical connection.
Delivered with
the actuator open
Delivered with
the actuator open
FPC
FPC
Space saving (30 pos. shown)
1.
Insulation resistance
500 Mø min.
2.
Withstanding voltage
No flashover or insulation breakdown
3. Contact resistance 100 mø max.
* Including FPC and FFC conductor resistance
4. Durability Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
5. Vibration
No electrical discontinuity of 1μs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
6. Shock
No electrical discontinuity of 1μs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
7.
Humidity (Steady state)
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
8. Temperature cycle
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
9.
Resistance to soldering heat
No deformation of components affecting performance
2
Termination type
SH : SMT horizontal mounting type
Specifications
(50)…Standard product 5,000 pieces/reel
(99)…500 pieces/reel
FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■Specifications
Ratings
Current rating 0.5 A (Note 1)
Voltage rating 50 Vrms AC
Operating temperature range:
-55 to +85°C (Note 1)
Operating humidity range:
Relative humidity 90% max. (No condensation)
Storage temperature range:
-10 to +50°C (Note 2)
Storage humidity range:
Relative humidity 90% max. (No condensation)
Recommended FPC/FFC Thickness: 0.3 ± 0.03 mm, Gold plated contact pads
Item Specification Conditions
100 V DC
250 Vrms AC / one minute
1 mA, AC / DC 20mV max (AC: 1kHz)
20 cycles
Frequency: 10 to 55 Hz, single amplitude of 0.75
mm, 10 cycles in each of the 3 axis
Acceleration of 981m/s2, 6 ms duration, sine half-
wave, 3 cycles in each of the 3 axis
96 hours at 40°C and humidity of 90 to 95%
Temperature : -55°C /+15°C to +35°C/+85°C /+15°C to +35°C
Time: 30 /2 to 3 /30 /2 to 3 minutes
5 cycles
Reflow: At the recommended temperature profile
Manual soldering: 350°C ±5°C for 5 seconds (Note 3)
Note1: When passing the current through all of the contacts, use 70% of the rated current.
Note2: Includes temperature rise caused by current flow.
Note3: The term "storage" refers to products stored for a long period prior to mounting and use.
The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage,
shipment or during transportation after board mounting.
■Ordering information
■Materials
Series name : FH
Series No. : 34S
Blank : Top contact
RJ : Top and Bottom contact, halogen-free
(Flame retardance UL94V-0).
Number of positions : 4 to 40
Contact pitch : 0.5mm
1
2
3
4
5
6
7
LCP(8pos.)
PA
LCP
Phosphor bronze
Phosphor bronze
FH34S series
FH34SRJ series
FH34S series
FH34SRJ series
FH34SRJ series
Color:Beige
Color:Gray
Color:Black
Color:Black
Gold plating with nickel barrier
Pure tin reflow plating
UL94V-0
UL94V-0
-------
-------
Insulator
Contacts
Metalfittings
Material Finish RemarksPart
FH 34S RJ - 30S - 0.5 SH (50)
1 2 4 53 6 7
3
CL580-1224-2-50
CL580-1228-3-50
CL580-1208-6-50
CL580-1238-7-50
CL580-1236-1-50
CL580-1231-8-50
CL580-1251-5-50
CL580-1258-4-50
CL580-1253-0-50
CL580-1252-8-50
CL580-1259-7-50
CL580-1248-0-50
CL580-1256-9-50
CL580-1254-3-50
CL580-1255-6-50
CL580-1247-8-50
CL580-1232-0-50
CL580-1261-9-50
CL580-1260-9-50
FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■Connector Dimensions
A**
1±0.1
(1.75)
(3.8)
2.9
0.3
2.9
0.5
1
0.1
∞Number of contacts
(1.95)
HRS mark
Cav No.
Number of contacts indicator
B
(C)
D±0.1
(0.15)
A±0.15
(0.15)
0.5
(3.2)
0.15 H
H
Note 1 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max.
Note 2 : Packaged on tape and reel only. Check packaging specification.
Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector.
Note 4 : After reflow, the terminal plating may change color, however this does not represent a quality issue.
Tape and reel packaging (5,000 pieces/reel, 500 pieces/reel).
Order by number of reels.
All dimensions: mm
Part Number
FH34S-7S-0.5SH(50)
FH34S-23S-0.5SH(50)
FH34S-32S-0.5SH(50)
FH34SRJ-4S-0.5SH(50)
FH34SRJ-6S-0.5SH(50)
FH34SRJ-8S-0.5SH(50)
FH34SRJ-10S-0.5SH(50)
FH34SRJ-11S-0.5SH(50)
FH34SRJ-12S-0.5SH(50)
FH34SRJ-14S-0.5SH(50)
FH34SRJ-16S-0.5SH(50)
FH34SRJ-18S-0.5SH(50)
FH34SRJ-20S-0.5SH(50)
FH34SRJ-22S-0.5SH(50)
FH34SRJ-24S-0.5SH(50)
FH34SRJ-26S-0.5SH(50)
FH34SRJ-30S-0.5SH(50)
FH34SRJ-34S-0.5SH(50)
FH34SRJ-40S-0.5SH(50)
7
23
32
4
6
8
10
11
12
14
16
18
20
22
24
26
30
34
40
5.5
13.5
18
4
5
6
7
7.5
8
9
10
11
12
13
14
15
17
19
22
3
11
15.5
1.5
2.5
3.5
4.5
5
5.5
6.5
7.5
8.5
9.5
10.5
11.5
12.5
14.5
16.5
19.5
4.03
12.07
16.53
2.53
3.53
4.53
5.53
6.03
6.53
7.53
8.57
9.57
10.57
11.57
12.57
13.57
15.57
17.53
20.53
4.88
12.88
17.38
3.38
4.38
5.38
6.38
6.88
7.38
8.38
9.38
10.38
11.38
12.38
13.38
14.38
16.38
18.38
21.38
CL No. Number of Contacts AB C D
4
4
12
16.5
2.5
3.5
4.5
5.5
6
6.5
7.5
8.5
9.5
10.5
11.5
12.5
13.5
15.5
17.5
20.5
FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
0.65±0.03
(Metal mask)
(0.25)
B
0.25±0.03
(Metal mask)
(0.25)
(A)
(2.9)
E±0.1
F±0.1
0.8±0.05
3.3±0.05
(0.15)
(0.15)
(0.065)
(0.185)
∞Number of contacts
0.5
0.8±0.05
0.3±0.05
Recommended metal mask thickness: t=0.1
0.1 J
J
1.5±0.3
2.5MIN(Stiffener)
H
(Uncover area)
G±0.05
B±0.03
0.3±0.03
2-R0.2
0.5±0.07
0.5±0.03 0.3±0.03
■Recommended PCB mounting pattern and metal mask dimensions
■Recommended FPC/FFC Dimensions
All dimensions: mm
Part Number
FH34S-7S-0.5SH(50)
FH34S-23S-0.5SH(50)
FH34S-32S-0.5SH(50)
FH34SRJ-4S-0.5SH(50)
FH34SRJ-6S-0.5SH(50)
FH34SRJ-8S-0.5SH(50)
FH34SRJ-10S-0.5SH(50)
FH34SRJ-11S-0.5SH(50)
FH34SRJ-12S-0.5SH(50)
FH34SRJ-14S-0.5SH(50)
FH34SRJ-16S-0.5SH(50)
FH34SRJ-18S-0.5SH(50)
FH34SRJ-20S-0.5SH(50)
FH34SRJ-22S-0.5SH(50)
FH34SRJ-24S-0.5SH(50)
FH34SRJ-26S-0.5SH(50)
FH34SRJ-30S-0.5SH(50)
FH34SRJ-34S-0.5SH(50)
FH34SRJ-40S-0.5SH(50)
CL580-1224-2-50
CL580-1228-3-50
CL580-1208-6-50
CL580-1238-7-50
CL580-1236-1-50
CL580-1231-8-50
CL580-1251-5-50
CL580-1258-4-50
CL580-1253-0-50
CL580-1252-8-50
CL580-1259-7-50
CL580-1248-0-50
CL580-1256-9-50
CL580-1254-3-50
CL580-1255-6-50
CL580-1247-8-50
CL580-1232-0-50
CL580-1261-9-50
CL580-1260-9-50
7
23
32
4
6
8
10
11
12
14
16
18
20
22
24
26
30
34
40
5.5
13.5
18
4
5
6
7
7.5
8
9
10
11
12
13
14
15
17
19
22
3
11
15.5
1.5
2.5
3.5
4.5
5
5.5
6.5
7.5
8.5
9.5
10.5
11.5
12.5
14.5
16.5
19.5
4.6
12.6
17.1
3.1
4.1
5.1
6.1
6.6
7.1
8.1
9.1
10.1
11.1
12.1
13.1
14.1
16.1
18.1
21.1
5.4
13.4
17.9
3.9
4.9
5.9
6.9
7.4
7.9
8.9
9.9
10.9
11.9
12.9
13.9
14.9
16.9
18.9
21.9
CL No. Number of Contacts A B E F G
Note 1 : Stiffener dimension should be 2.5mm min., and H dimension should be 0.5mm for improved flexibility of FPC.
Note 2 : When using the FPC/FFC in FH34S or FH19SC connectors, the exposed area inserted in either connector is 2.5mm ±
0.3mm and the stiffener is 3.5mm min.
5
FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■
Recommended FPC construction
●Contact FPC manufacturer for specific details.
1. Using Single-sided FPC FPC : Flexible Printed Circuit
Material Name Material
Material Thickness
(μm)
Covering film layer
Cover adhesive
Polyimide 1 mil thick (25)
(25)
Surface treatment
0.2μm thick gold plated over 1
to 5μm thick nickel underplating
3
Copper foil
Base adhesive
Base film
Reinforcement material adhesive
Stiffener
Cu 1oz
Thermosetting adhesive
Polyimide 1 mil thick
Thermosetting adhesive
Polyimide 7 mil thick
35
25
25
35
175
Total 298
3. Using FFC FFC : Flexible Flat Cable
Polyester film
Adhesive Thermoplastic polyester
(12)
(30)
35
30
12
30
188
295
Material Name Material
Material Thickness
(μm)
Gold plated annealed copper foil
Adhesive
Polyester
Adhesive
Stiffener
Polyester
Polyester
Polyester
Total
(25)
(25)
2. Using Double-sided FPC
* To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back
side is not recommended.
FPC : Flexible Printed Circuit
Material Name
Covering layer film
Cover adhesive
Material
Material Thickness
(μm)
Polyimide 1 mil thick
Surface treatment
0.2μm thick gold plated over 1
to 5μm thick nickel underplating
3
Through-hole copper
Copper foil
Base adhesive
Base film
Base adhesive
Cu
Cu 1/2oz
Thermosetting adhesive
Polyimide 1 mil thick
15
18
18
25
18
Copper foil
Cover adhesive
Covering film layer
Reinforcement material adhesive
Stiffener
Cu 1/2oz
Thermosetting adhesive
Polyimide 1 mil thick
Thermosetting adhesive
Polyimide 4 mil thick
(18)
25
25
50
100
Total 297
1. This specification is a recommendation for the construction of the FH34S Series FPC and FFC (t=0.3 ± 0.03).
2. For details about the construction, please contact the FPC/FFC manufacturers.
4. Precautions
6
FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
0
L±0.3
1.75±0.1
Flat surface,
for placement with
automatic equipment
8±0.12±0.154±0.1
M±0.1
Ø1.5
+0.1
Unreeling direction
(0.3)
(2.25)
(3.2)
(4)
(1.95)
Ø1.5 +0.1
0
(1.95)
(2.25)
(0.3)
Flat surface, for placement
with automatic equipment
Unreeling direction
1.7+0.15
1.5+0.1
L±0.3
M±0.1 1.75±0.1
N±0.1
0
0
End section Mounting section
Embossed carrier tape
Lead section (400mm min.)
Top cover tape
No connector inserted
(10 pockets min.)
No connector inserted
(10 pockets min.)
■Packaging Specification
●Embossed Carrier Tape Dimensions
(Tape width 24mm max.)
Ø13±0.5
(Ø80)
(Ø380)
(Q: INSIDE)
(R: OUTSIDE)
●Reel Dimensions
●Embossed Carrier Tape Dimensions
(Tape width of 32mm min.)
All dimensions: mm
Part Number
FH34S-7S-0.5SH(50)
FH34S-23S-0.5SH(50)
FH34S-32S-0.5SH(50)
FH34SRJ-4S-0.5SH(50)
FH34SRJ-6S-0.5SH(50)
FH34SRJ-8S-0.5SH(50)
FH34SRJ-10S-0.5SH(50)
FH34SRJ-11S-0.5SH(50)
FH34SRJ-12S-0.5SH(50)
FH34SRJ-14S-0.5SH(50)
FH34SRJ-16S-0.5SH(50)
FH34SRJ-18S-0.5SH(50)
FH34SRJ-20S-0.5SH(50)
FH34SRJ-22S-0.5SH(50)
FH34SRJ-24S-0.5SH(50)
FH34SRJ-26S-0.5SH(50)
FH34SRJ-30S-0.5SH(50)
FH34SRJ-34S-0.5SH(50)
FH34SRJ-40S-0.5SH(50)
CL580-1224-2-50
CL580-1228-3-50
CL580-1208-6-50
CL580-1238-7-50
CL580-1236-1-50
CL580-1231-8-50
CL580-1251-5-50
CL580-1258-4-50
CL580-1253-0-50
CL580-1252-8-50
CL580-1259-7-50
CL580-1248-0-50
CL580-1256-9-50
CL580-1254-3-50
CL580-1255-6-50
CL580-1247-8-50
CL580-1232-0-50
CL580-1261-9-50
CL580-1260-9-50
7
23
32
4
6
8
10
11
12
14
16
18
20
22
24
26
30
34
40
CL No. Number of Contacts
16
24
32
16
16
16
16
16
24
24
24
24
24
24
24
24
32
32
44
7.5
11.5
14.2
7.5
7.5
7.5
7.5
7.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
14.2
14.2
20.2
—
—
28.4
—
—
—
-
-
-
-
-
-
-
-
-
-
28.4
28.4
40.4
17.4
25.4
33.4
17.4
17.4
17.4
17.4
17.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
33.4
33.4
45.4
21.4
29.4
37.4
21.4
21.4
21.4
21.4
21.4
29.4
29.4
29.4
29.4
29.4
29.4
29.4
29.4
37.4
37.4
49.4
L M N Q R
7
FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■Operation and Precautions
Exercise care when handling connectors. Follow recommendations given below.
1. As delivered
Delivered with the
actuator open. There is
no need to operate the
actuator prior to inserting
the FPC/FFC.
Operation
2.
FPC/FFC insertion (The top contact specification)
Insert the FPC/FFC with
the conductive surfaces
facing up.
Align the FPC/FFC
straight with the
connector and insert it
firmly all the way.
• Do not close the actuator without the FPC/FPC
inserted.
Precautions
• The contacts are making connection with the
FPC/FFC pads from the top.
Do not insert the FPC/FFC with the pads facing
down.
When inserting the FPC/FFC do not twist it. Insert
straight. Improper insertion may cause deformation
of the contacts and connection failures.
• Be sure to insert the FPC/FFC when the actuator is
fully open.
FPC/FFC contact
surfaces face up.
3. Locking
After FPC/FFC insertion, rotate the actuator down
to a full stop, pushing it at the center.
• Do not operate the actuator by only one end. Open
or close by pushing at the center.
• Do not try to rotate the actuator past the fully open
90° position. This will damage the connector,
preventing it from use.
• Do not apply excessive force to the connector when
the actuator is closed.
Rotate
Push at the center of the actuator.
4. FPC/FFC removal (Lock release)
Carefully rotate the actuator up to 90°, lifting it at
the center.
• Do not operate the actuator from one end only.
• The actuator opens only 90°. Do not attempt to
open it past this angle or grasp it.
• During the opening of the actuator do not press it
toward the connector body. Rotate up at the center.
Raise Lift at the center
8
FH34(S)Series●0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■Precautions at the Design Stage
(1) Route the FPC/FFC so that a direct pull force
(2) Make sure that there is enough space to insert/remove the FPC/FFC straight.
(3) Follow the recommendations given in this catalog in regard to mounting pattern, metal mask dimensions and
FPC/FFC mating dimensions.
(4) Consult the manufacturer of the FPC/FFC for the details on the flexibility of the specific FPC/FFC.
(5) When designing the board lay-out and spaces in the device assure that there is enough clearances for the actuator to
fully open/close.
◆When hand soldering:
· Do not perform hand soldering with the FPC inserted in the connector.
* Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads.
* Do not use excessive amount of solder or flux compounds.
Operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds.
◆Handling before mounting on PCB
Insertion of the FPC/FFC or operation of the actuator prior to mounting on the PCB is not recommended.
◆PC board warpage
Minimize the warpage as much as possible. The connector are straight within 0.1 mm max. Make sure that the
mounting area flatness can accept the connector terminals without causing any failure of the solder joints.
◆Forces on the board
◆When braking the large PC board into individual boards exercise care not to damage the installed connectors.
◆When attaching the boards or other components with the screws
make sure that any stresses will not cause board deflections
affecting the mounting areas of the connector.
■Precautions when mounting connectors on the PCB
Connectors
PCB
MAX 250ç
Start
Temperature(ç)
Time (Seconds)
25ç (60 sec.)
(60 sec.)
90 to 120 sec.
Preheating
Soldering
0
50
100
150 150ç
200ç
230ç
200
250
HRS test condition
Solder method : Reflow, IR/hot air
Environment : Room air
Solder composition : Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.'s Part
Number:
M705-221CM5-42-10.5)
Test board : Glass epoxy
25mm∞40mm∞0.8mm thick
Land dimensions : 0.3mm∞0.8mm
Metal mask : 0.25∞0.65∞0.1mm thick
The temperature profiles shown are based on the above
conditions.
In individual applications the actual temperature may
vary, depending on solder paste type, volume / thickness
and board size / thickness. Consult your solder paste and
equipment manufacturer for specific recommendations.
■Temperature Profile