256-Position Two-Time Programmable
I2C Digital Potentiometer
Preliminary Technical Data
AD5170
FEATURES
256-position
TTP(Two-Time Programmable) Set-and-Forget sesistance
setting allows second chance permanent programming
End-to-end resistance 2.5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ
Compact MSOP-10 (3 mm × 4.9 mm) Package
Fast Settling Time: tS = 5µs Typ in Power-Up
Full read/write of wiper register
Power-on preset to midscale
Extra package address decode pins AD0 and AD1
Computer Software Replaces µC in Factory Programming
Applications
Single supply 2.7 V to 5.5 V
Low temperature coefficient 35 ppm/°C
Low power, IDD = 5 µA
Wide operating temperature –40°C to +125°C
Evaluation board available
APPLICATIONS
Systems Calibrations
Electronics Level Settings
Mechanical Trimmers® Replacement in New Designs
Permamenent Factory PCB Setting
Transducer adjustment of pressure, temperature, position,
chemical, and optical sensors
RF amplifier biasing
Automotive electronics adjustment
Gain control and offset adjustment
GENERAL OVERVIEW
The AD5170 is a 256-position, Two-Time Programmable(TTP)
digital potentiometer that employs fuse link technology to
enable two opportunities at permanently programming the
resistance setting. This device performs the same electronic
adjustment function as mechanical potentiometers or variable
resistors, with enhanced resolution, solid-state reliability, and
superior low temperature coefficient performance.
The AD5170 is controlled using a 2-wire, I2C compatible digital
interface. It allows unlimited adjustments before
permanently”(you really have two opportunities) setting the
resistance value. After the final value is determined, a fuse blow
command is executed which freezes the wiper
position(analogous to placing epoxy on a mechanical trimmer).
In addition, for applications that program the AD5170 at the
factory, Analog Devices offers device programming software
running on Windows® NT, 2000, and XP operating systems.
This software effectively replaces any external I2C controllers,
which in turn enhances users systems time-to-market.
An AD5170 evaluation kit and software are available. The kit
includes the connector and cable that can be converted for
further factory programming applications.
FUNCTIONAL BLOCK DIAGRAMS
RDAC
REGISTER
ADDRESS
DECODE
SERIAL INPUT
REGISTER
AWB
8
VDD
GND
SDA
SCL
FUSE
LINKS
12
AD0
AD1
Figure 1. AD5170
Note:
The terms digital potentiometer, VR, and RDAC are used interchangeably.
Purchase of licensed I2C components of Analog Devices or one of its sublicensed
Associated Companies conveys a license for the purchaser under the Philips I2C
Patent Rights to use these components in an I2C system, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.326.8703 © 2003 Analog Devices, Inc. All rights reserved.
Rev. PrE7/9/03
AD5170
Preliminary Technical Data
TABLE OF CONTENTS
Electrical Characteristics—2.5 kΩ Version................................... 3
Electrical Characteristics—10 kΩ, 50 kΩ, 100 kΩ Versions ....... 4
Timing Characteristics—2.5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ Versions
............................................................................................................. 5
Absolute Maximum Ratings1.......................................................... 5
Typical Performance Characteristics ............................................. 6
Test Circuits....................................................................................... 7
I2C Interface....................................................................................... 8
Operation......................................................................................... 10
Programming the Variable Resistor ......................................... 10
Programming the Potentiometer Divider............................... 11
I2C Compatible 2-Wire Serial Bus............................................ 11
Level Shifting for Bidirectional Interface ................................ 12
ESD Protection ........................................................................... 12
Terminal Voltage Operating Range.......................................... 13
Power-Up Sequence ................................................................... 13
POWER supply Considerations ............................................... 13
Layout and Power Supply Bypassing ....................................... 13
Pin Configuration and Function Descriptions........................... 14
Pin Configuration ...................................................................... 14
Pin Function Descriptions ..... Error! Bookmark not defined.
Outline Dimensions....................................................................... 15
Ordering Guide .......................................................................... 15
ESD Caution................................................................................ 15
REVISION HISTORY
Revision 0: Initial Version
Rev. PrE 7/9/03 | Page 2 of 15
Preliminary Technical Data
AD5170
ELECTRICAL CHARACTERISTICS—2.5 kΩ VERSION
(VDD = 5 V ± 10%, or 3 V ± 10%; VA = +VDD; VB = 0 V; –40°C < TA < +125°C; unless otherwise noted.)
Table 1.
Parameter Symbol Conditions Min Typ1 Max Unit
DC CHARACTERISTICS—RHEOSTAT MODE
Resistor Differential Nonlinearity2 R-DNL RWB, VA = no connect –1.5 ±0.1 +1.5 LSB
Resistor Integral Nonlinearity2 R-INL RWB, VA = no connect –4 ±0.75 +4 LSB
Nominal Resistor Tolerance3 ∆RAB T
A = 25°C –30 +30 %
Resistance Temperature Coefficient ∆RAB/∆T VAB = VDD, Wiper = no connect 35 ppm/°C
Wiper Resistance RW 50 120
DC CHARACTERISTICS—POTENTIOMETER DIVIDER MODE (Specifications apply to all VRs)
Resolution N 8 Bits
Differential Nonlinearity4 DNL –1.5 ±0.1 +1.5 LSB
Integral Nonlinearity4 INL –1.5 ±0.6 +1.5 LSB
Voltage Divider Temperature Coefficient ∆VW/∆T Code = 0x80 15 ppm/°C
Full-Scale Error VWFSE Code = 0xFF –6 –2.5 0 LSB
Zero-Scale Error VWZSE Code = 0x00 0 +2 +6 LSB
RESISTOR TERMINALS
Voltage Range5 V
A,B,W GND VDD V
Capacitance6 A, B CA,B f = 1 MHz, measured to GND,
Code = 0x80
45 pF
Capacitance6 W CW f = 1 MHz, measured to GND,
Code = 0x80
60 pF
Shutdown Supply Current7 I
DD_SD VDD = 5.5 V 0.01 1 µA
Common-Mode Leakage ICM V
A = VB = VDD/2 1 nA
DIGITAL INPUTS AND OUTPUTS
Input Logic High VIH 2.4 V
Input Logic Low VIL 0.8 V
Input Logic High VIH V
DD = 3 V 2.1 V
Input Logic Low VIL V
DD = 3 V 0.6 V
Input Current IIL V
IN = 0 V or 5 V ±1 µA
Input Capacitance6 C
IL 5 pF
POWER SUPPLIES
Power Supply Range VDD RANGE 2.7 5.5 V
Supply Current IDD V
IH = 5 V or VIL = 0 V 3 5 µA
Power Dissipation8 P
DISS V
IH = 5 V or VIL = 0 V, VDD = 5 V 0.2 mW
Power Supply Sensitivity PSS ∆VDD = +5 V ± 10%,
Code = Midscale
±0.02 ±0.05 %/%
DYNAMIC CHARACTERISTICS6, 9
Bandwidth –3dB BW_5K RAB = 2.5 kΩ, Code = 0x80 2.4 MHz
Total Harmonic Distortion THDW V
A = 1 V rms, VB = 0 V, f = 1 kHz 0.05 %
V
W Settling Time tS VA= 5 V, VB = 0 V, ±1 LSB error
band
1 µs
Resistor Noise Voltage Density eN_WB R
WB = 2.5 kΩ, RS = 0 4.5 nV/√Hz
Rev. PrE 7/9/03 | Page 3 of 15
AD5170
Preliminary Technical Data
ELECTRICAL CHARACTERISTICS—10 kΩ, 50 kΩ, 100 kΩ VERSIONS
(VDD = 5 V ± 10%, or 3 V ± 10%; VA = VDD; VB = 0 V; –40°C < TA < +125°C; unless otherwise noted.)
Table 2.
Parameter Symbol Conditions Min Typ1 Max Unit
DC CHARACTERISTICS—RHEOSTAT MODE
Resistor Differential Nonlinearity2 R-DNL RWB, VA = no connect –1 ±0.1 +1 LSB
Resistor Integral Nonlinearity2 R-INL RWB, VA = no connect –2 ±0.25 +2 LSB
Nominal Resistor Tolerance3 ∆RAB T
A = 25°C –30 +30 %
Resistance Temperature Coefficient ∆RAB/∆T VAB = VDD,
Wiper = no connect
35 ppm/°C
Wiper Resistance RW V
DD = 5 V 50 120
DC CHARACTERISTICS—POTENTIOMETER DIVIDER MODE (Specifications apply to all VRs)
Resolution N 8 Bits
Differential Nonlinearity4 DNL –1 ±0.1 +1 LSB
Integral Nonlinearity4 INL –1 ±0.3 +1 LSB
Voltage Divider Temperature Coefficient ∆VW/∆T Code = 0x80 15 ppm/°C
Full-Scale Error VWFSE Code = 0xFF –3 –1 0 LSB
Zero-Scale Error VWZSE Code = 0x00 0 1 3 LSB
RESISTOR TERMINALS
Voltage Range5 V
A,B,W GND VDD V
Capacitance6 A, B CA,B f = 1 MHz, measured to
GND, Code = 0x80
45 pF
Capacitance6 W CW f = 1 MHz, measured to
GND, Code = 0x80
60 pF
Shutdown Supply Current7 I
DD_SD VDD = 5.5 V 0.01 1 µA
Common-Mode Leakage ICM V
A = VB = VDD/2 1 nA
DIGITAL INPUTS AND OUTPUTS
Input Logic High VIH 2.4 V
Input Logic Low VIL 0.8 V
Input Logic High VIH V
DD = 3 V 2.1 V
Input Logic Low VIL V
DD = 3 V 0.6 V
Input Current IIL V
IN = 0 V or 5 V ±1 µA
Input Capacitance6 C
IL 5 pF
POWER SUPPLIES
Power Supply Range VDD RANGE 2.7 5.5 V
Supply Current IDD V
IH = 5 V or VIL = 0 V 3 5 µA
Power Dissipation8 P
DISS VIH = 5 V or VIL = 0 V,
VDD = 5 V
0.2 mW
Power Supply Sensitivity PSS ∆VDD = +5 V ± 10%,
Code = Midscale
±0.02 ±0.05 %/%
DYNAMIC CHARACTERISTICS6, 9
Bandwidth –3dB BW RAB = 10 kΩ/50 kΩ/100 kΩ,
Code = 0x80
600/100/40 kHz
Total Harmonic Distortion THDW VA =1 V rms, VB = 0 V,
f = 1 kHz, RAB = 10 kΩ
0.05 %
V
W Settling Time (10 kΩ/50 kΩ/100 kΩ) tS VA = 5 V, VB = 0 V,
±1 LSB error band
2 µs
Resistor Noise Voltage Density eN_WB R
WB = 5 kΩ, RS = 0 9 nV/√Hz
Rev. PrE 7/9/03 | Page 4 of 15
Preliminary Technical Data
AD5170
TIMING CHARACTERISTICS—2.5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ VERSIONS
(VDD = +5V ± 10%, or +3V ± 10%; VA = VDD; VB = 0 V; –40°C < TA < +125°C; unless otherwise noted.)
Table 3.
Parameter Symbol Conditions Min Typ1 Max Unit
I2C INTERFACE TIMING CHARACTERISTICS6, 10 (Specifications Apply to All Parts)
SCL Clock Frequency fSCL 400 kHz
t
BUF Bus Free Time between STOP and START t1 1.3 µs
t
HD;STA Hold Time (Repeated START) t2 After this period, the first clock pulse is
generated.
0.6 µs
t
LOW Low Period of SCL Clock t3 1.3 µs
t
HIGH High Period of SCL Clock t4 0.6 50 µs
t
SU;STA Setup Time for Repeated START Condition t5 0.6 µs
t
HD;DAT Data Hold Time t6 0.9 µs
t
SU;DAT Data Setup Time t7 100 ns
t
F Fall Time of Both SDA and SCL Signals t8 300 ns
t
R Rise Time of Both SDA and SCL Signals t9 300 ns
t
SU;STO Setup Time for STOP Condition t10 0.6 µs
NOTES
1 Typical specifications represent average readings at +25°C and VDD = 5 V.
2 Resistor position nonlinearity error R-INL is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic.
3 VAB = VDD, Wiper (VW) = no connect.
4 INL and DNL are measured at VW with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. VA = VDD and VB = 0 V.
DNL specification limits of ±1 LSB maximum are guaranteed monotonic operating conditions.
5 Resistor terminals A, B, W have no limitations on polarity with respect to each other.
6 Guaranteed by design and not subject to production test.
7 Measured at the A terminal. The A terminal is open circuited in shutdown mode.
8 PDISS is calculated from (IDD × VDD). CMOS logic level inputs result in minimum power dissipation.
9 All dynamic characteristics use VDD = 5 V.
10 See timing diagrams for locations of measured values.
ABSOLUTE MAXIMUM RATINGS1
(TA = +25°C, unless otherwise noted.)
Table 4.
Parameter Value
VDD to GND –0.3 V to +7 V
VA, VB, VW to GND VDD
IMAX1 ±20 mA
Digital Inputs and Output Voltage to GND 0 V to +7 V
Operating Temperature Range –40°C to +125°C
Maximum Junction Temperature (TJMAX) 150°C
Storage Temperature –65°C to +150°C
Lead Temperature (Soldering, 10 sec) 300°C
Thermal Resistance2 θJA: MSOP-10 230°C/W
NOTES
1 Maximum terminal current is bounded by the maximum current handling of
the switches, maximum power dissipation of the package, and maximum
applied voltage across any two of the A, B, and W terminals at a given
resistance.
2 Package power dissipation = (TJMAX – TA)/θJA.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. PrE 7/9/03 | Page 5 of 15
AD5170
Preliminary Technical Data
TYPICAL PERFORMANCE CHARACTERISTICS
Rev. PrE 7/9/03 | Page 6 of 15
Preliminary Technical Data
AD5170
TEST CIRCUITS
Figure 2 to Figure 10 illustrate the test circuits that define the
test conditions used in the product specification tables.
V
MS
AW
B
DUT V+ = VDD
1LSB = V+/2N
V+
Figure 2. Test Circuit for Potentiometer Divider Nonlinearity Error (INL, DNL)
NO CONNECT
IW
VMS
AW
B
DUT
Figure 3. Test Circuit for Resistor Position Nonlinearity Error
(Rheostat Operation; R-INL, R-DNL)
V
MS1
I
W
= V
DD
/R
NOMINAL
V
MS2
V
W
R
W
= [V
MS1
– V
MS2
]/I
W
AW
B
DUT
Figure 4. Test Circuit for Wiper Resistance
V
V
V
V
MS
%
DD
%
PSS (%/%) =
V+ = V
DD
10%
PSRR (dB) = 20 LOG
MS
DD
( )
V
DD
V
A
V
MS
AW
B
V+
Figure 5. Test Circuit for Power Supply Sensitivity (PSS, PSSR)
OP279
W
5V
B
V
OUT
OFFSET
GND OFFSET
BIAS
ADUT
V
IN
Figure 6. Test Circuit for Inverting Gain
B
A
V
IN
OP279
W
5V
V
OUT
OFFSET
GND
OFFSET
BIAS
DUT
Figure 7. Test Circuit for Noninverting Gain
+15V
–15V
W
A
2.5V
B
V
OUT
OFFSET
GND
DUT
AD8610
V
IN
Figure 8. Test Circuit for Gain vs. Frequency
W
B
V
SS
TO V
DD
DUT
I
SW
CODE = 0x00
R
SW
=0.1V
I
SW
0.1V
Figure 9. Test Circuit for Incremental ON Resistance
W
BV
CM
I
CM
A
NC
GND
NC
V
SS
V
DD
DUT
NC = NO CONNECT
Figure 10. Test Circuit for Common-Mode Leakage current
Rev. PrE 7/9/03 | Page 7 of 15
AD5170
Preliminary Technical Data
I2C INTERFACE
Table 5. Write Mode
S 0 1 0 1 1 AD1 AD0
W A 2T SD T 0 OV X X X A D7 D6 D5 D4 D3 D2 D1 D0 A P
Slave Address Byte Instruction Byte Data Byte
Table 6. Read Mode
S 0 1 0 1 1 AD1 AD0 R A D7 D6 D5 D4 D3 D2 D1 D0 A E1 E0 X X X X X X A P
Slave Address Byte Instruction Byte Data Byte
S = Start Condition
P = Stop Condition
A = Acknowledge
X = Dont Care
W = Write
R = Read
2T = Second fuse link array for Two Time Programming.
Logic 0 corresponds to first trim. Logic 1 corresponds to
second trim.
SD = Shutdown connects wiper to B terminal and open
circuits A terminal. It does not change contents of wiper
register.
T = OTP Programming Bit. Logic 1 programs wiper
permanently.
OV = Overwrite fuse setting and program digital pot to
different setting. Note that upon power up, digital pot will
preset to either midscale or fuse setting depending on whether
or not the fuse link has been blown.
D7, D6, D5, D4, D3, D2, D1, D0 = Data Bits
E1, E0 = OTP Validation Bits
0 , 0 = Ready to program
0 , 1 = Test fuse not blown successfully(check setup)
1 , 0 = Fatal error. Retry.
1 , 1 =Programmed Successfully. No further
adjustments possible.
Rev. PrE 7/9/03 | Page 8 of 15
Preliminary Technical Data
AD5170
t
1
t
3
t
4
t
2
t
7
t
8
t
9
PS PS
t
10
t
5
t
9
t
8
SCL
SD
A
t
2
t
6
Figure 11. I2C Interface Detailed Timing Diagram
SCL
FRAME 1 FRAME 2
START BY
MASTER
ACK BY
AD5170
SLAVE ADDRESS BYTE STOP BY
MASTERINSTRUCTION BYTE
SDA 0 1 0 1 1 AD1 AD0 R/W 2T SD 0OV X X X
1 91 9
D7 D6 D5 D4 D3 D2 D1 D0
ACK BY
AD5170 FRAME 3
DATA BYTE
19
ACK BY
AD5170
T
Figure 12. Writing to the RDAC Register
SCL
FRAME 1 FRAME 2
START BY
MASTER
ACK BY
AD5170
SLAVE ADDRESS BYTE STOP BY
MASTER DATA BYTE
SDA 0 1 0 1 1 AD1 AD0 R/W D7 D6 D4 D3 D2 D1 D0
1 91 9
E1 E0 X X X X X X
ACK BY
MASTER FRAME 3
VERIFICATION BYTE
19
NO ACK
BY MASTER
D5
Figure 13 Reading Data from the RDAC Register
Rev. PrE 7/9/03 | Page 9 of 15
AD5170
Preliminary Technical Data
OPERATION
The AD5170 is a 256-position digitally controlled variable
resistor (VR) device.
An internal power-on preset places the wiper at midscale
during power-on, which simplifies the fault condition recovery
at power-up.
If the device has been permanently programmed via the fuse
link technology, the device will power up at that permanent
setting.
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance of the RDAC between terminals A and
B is available in 5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ. The final two
or three digits of the part number determine the nominal
resistance value, e.g., 10 kΩ = 10; 50 kΩ = 50. The nominal
resistance (RAB) of the VR has 256 contact points accessed by
the wiper terminal, plus the B terminal contact. The 8-bit data
in the RDAC latch is decoded to select one of the 256 possible
settings. Assume a 10 kΩ part is used, the wiper’s first
connection starts at the B terminal for data 0x00. Since there is a
60 Ω wiper contact resistance, such connection yields a
minimum of 60 Ω resistance between terminals W and B. The
second connection is the first tap point, which corresponds to
99 Ω (RWB = RAB/256 + RW = 39 Ω + 60 Ω) for data 0x01.
The third connection is the next tap point, representing 138 Ω
(2 × 39 Ω + 60 Ω) for data 0x02, and so on. Each LSB data value
increase moves the wiper up the resistor ladder until the last tap
point is reached at 9961 Ω (RAB – 1 LSB + RW). Figure 14 shows
a simplified diagram of the equivalent RDAC circuit where the
last resistor string will not be accessed; therefore, there is 1 LSB
less of the nominal resistance at full scale in addition to the
wiper resistance.
B
RDAC
LATCH
AND
DECODER
W
A
R
S
R
S
R
S
R
S
SD BIT
D7
D6
D4
D5
D2
D3
D1
D0
Figure 14. AD5170 Equivalent RDAC Circuit
The general equation determining the digitally programmed
output resistance between W and B is
W
AB
WB RR
D
DR +×= 256
)( (1)
where D is the decimal equivalent of the binary code loaded in
the 8-bit RDAC register, RAB is the end-to-end resistance, and
RW is the wiper resistance contributed by the on resistance of
the internal switch.
In summary, if RAB = 10 kΩ and the A terminal is open
circuited, the following output resistance RWB will be set for the
indicated RDAC latch codes.
Table 7. Codes and Corresponding RWB Resistance
D (Dec.) RWB (Ω) Output State
255 9,961 Full Scale (RAB – 1 LSB + RW)
128 5,060 Midscale
1 99 1 LSB
0 60 Zero Scale (Wiper Contact Resistance)
Note that in the zero-scale condition a finite wiper resistance of
60 Ω is present. Care should be taken to limit the current flow
between W and B in this state to a maximum pulse current of
no more than 20 mA. Otherwise, degradation or possible
destruction of the internal switch contact can occur.
Similar to the mechanical potentiometer, the resistance of the
RDAC between the wiper W and terminal A also produces a
digitally controlled complementary resistance RWA . When these
terminals are used, the B terminal can be opened. Setting the
resistance value for RWA starts at a maximum value of resistance
and decreases as the data loaded in the latch increases in value.
The general equation for this operation is
W
ABWA RR
D
DR +×
=256
256
)( (2)
For RAB = 10 kΩ and the B terminal open circuited, the
following output resistance RWA will be set for the indicated
RDAC latch codes.
Table 8. Codes and Corresponding RWA Resistance
D (Dec.) RWA (Ω) Output State
255 99 Full Scale
128 5,060 Midscale
1 9,961 1 LSB
0 10,060 Zero Scale
Typical device to device matching is process lot dependent and
may vary by up to ±30%. Since the resistance element is
Rev. PrE 7/9/03 | Page 10 of 15
Preliminary Technical Data
AD5170
processed in thin film technology, the change in RAB with
temperature has a very low 45 ppm/°C temperature coefficient.
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates a voltage divider at
wiper-to-B and wiper-to-A proportional to the input voltage at
A-to-B. Unlike the polarity of VDD to GND, which must be
positive, voltage across A-B, W-A, and W-B can be at either
polarity.
If ignoring the effect of the wiper resistance for approximation,
connecting the A terminal to 5 V and the B terminal to ground
produces an output voltage at the wiper-to-B starting at 0 V up
to 1 LSB less than 5 V. Each LSB of voltage is equal to the
voltage applied across terminal AB divided by the 256 positions
of the potentiometer divider. The general equation defining the
output voltage at VW with respect to ground for any valid input
voltage applied to terminals A and B is
B
A
WV
D
V
D
DV
256
256
256
)(
+= (3)
For a more accurate calculation, which includes the effect of
wiper resistance, VW, can be found as
B
AB
WA
A
AB
WB
WV
R
DR
V
R
DR
DV )()(
)( += (4)
Operation of the digital potentiometer in the divider mode
results in a more accurate operation over temperature. Unlike
the rheostat mode, the output voltage is dependent mainly on
the ratio of the internal resistors RWA and RWB and not the
absolute values. Therefore, the temperature drift reduces to
15 ppm/°C.
I2C COMPATIBLE 2-WIRE SERIAL BUS
The 2-wire I2C serial bus protocol operates as follows:
1. The master initiates data transfer by establishing a START
condition, which is when a high-to-low transition on the
SDA line occurs while SCL is high. The following byte is
the slave address byte, which consists of the slave address
followed by an R/W bit (this bit determines whether data
will be read from or written to the slave device). AD0 and
AD1 are configurable address bits which allow up to four
devices on one bus(see Table 5).
The slave whose address corresponds to the transmitted
address responds by pulling the SDA line low during the
ninth clock pulse (this is termed the acknowledge bit). At
this stage, all other devices on the bus remain idle while the
selected device waits for data to be written to or read from
its serial register. If the R/W bit is high, the master will read
from the slave device. On the other hand, if the R/W bit is
low, the master will write to the slave device.
2. In the write mode, the second byte is the instruction byte.
The first bit (MSB), 2T, of the instruction byte is the second
trim enable bit. A logic low will select trim#1 and a logic
high will select trim#2. This means that after blowing the
fuses with trim#1, you still have another chance to blow
them again w/ trim #2. Note that using trim#2 before
trim#1 will effectively disable trim#1 and in turn only
allow one time programming.
The second MSB, SD, is a shutdown bit. A logic high
causes an open circuit at terminal A while shorting the
wiper to terminal B. This operation yields almost 0 Ω in
rheostat mode or 0 V in potentiometer mode. It is
important to note that the shutdown operation does not
disturb the contents of the register. When brought out of
shutdown, the previous setting will be applied to the
RDAC. Also, during shutdown, new settings can be
programmed. When the part is returned from shutdown,
the corresponding VR setting will be applied to the RDAC.
The third MSB, T, is the OTP(One Time Programmable)
programming bit. A logic high blows the poly fuses and
programs the resistor setting permanently. For example, if
you wanted to use blow the first array of fuses, the
instruction byte would be 00100XXX. If you wanted to
blow the second array of fuses, your instruction byte would
be 10100XXX. A logic low of the T bit simply allows the
device to act as a typical volatile digital potentiometer.
The fourth MSB must always be at a logic zero.
The fifth MSB, OW, is an overwrite bit. When raised to a
logic high, this bit allows the RDAC setting to be changed
even after the internal fuses have been blown. However,
once the OW bit is returned to a logic zero, the position of
the RDAC will return to the setting prior to overwrite.
Because OW is not static, if the device is powered off and
on, the RDAC will preset to midscale or to the setting at
which the fuses were blown depending on whether or not
the fuses have been permanently set already.
The remainder of the bits in the instruction byte are don’t
cares(see Table 5).
After acknowledging the instruction byte, the last byte in
write mode is the data byte. Data is transmitted over the
serial bus in sequences of nine clock pulses (eight data bits
followed by an acknowledge bit). The transitions on the
SDA line must occur during the low period of SCL and
remain stable during the high period of SCL (see Table 5).
3. In the read mode, the data byte follows immediately after
Rev. PrE 7/9/03 | Page 11 of 15
AD5170
Preliminary Technical Data
the acknowledgment of the slave address byte. Data is
transmitted over the serial bus in sequences of nine clock
pulses(a slight difference with the write mode, where there
are eight data bits followed by an acknowledge bit).
Similarly, the transitions on the SDA line must occur
during the low period of SCL and remain stable during the
high period of SCL (see Figure 13).
Following the data byte, the validation byte contains two
validation bits, E0 and E1. These bits signify the status of
the One Time Programming(see Table 9).
4. After all data bits have been read or written, a STOP
condition is established by the master. A STOP condition is
defined as a low-to-high transition on the SDA line while
SCL is high. In write mode, the master will pull the SDA
line high during the tenth clock pulse to establish a STOP
condition. In read mode, the master will issue a No
Acknowledge for the ninth clock pulse (i.e., the SDA line
remains high). The master will then bring the SDA line low
before the tenth clock pulse which goes high to establish a
STOP condition (see Figure 13).
A repeated write function gives the user flexibility to update the
RDAC output a number of times after addressing and
instructing the part only once. For example, after the RDAC has
acknowledged its slave address and instruction bytes in the
write mode, the RDAC output will update on each successive
byte. If different instructions are needed, the write/read mode
has to start again with a new slave address, instruction, and data
byte. Similarly, a repeated read function of the RDAC is also
allowed.
Table 9. Validation Status
E1 E0 Status
0 0 Ready for Programming
0 1 Test Fuse Not Blown Successfully
(Check Setup)
1 0 Fatal Error. Some Fuses are not
Blown. Retry Again
1 1 Successful. No Further
Programming is Possible
Multiple Devices on One Bus
Figure 15 shows four AD5170 devices on the same serial bus.
Each has a different slave address since the states of their AD0
and AD1 pins are different. This allows each device on the bus
to be written to or read from independently. The master device
output bus line drivers are open-drain pull-downs in a fully I2C
compatible interface.
SD A S CL
AD51 70
AD1
AD0
M
A
STER
SD
A
SCL
Rp Rp
+
5
V
SDA S
C
L
AD5
1
7
0
AD1
AD0
S
D
A S
C
L
A
D
5
1
7
0
A
D
1
A
D
0
S D A SC L
AD5 17 0
AD1
AD0
+5
D
V+
5
V
+5 V
Figure 15. Multiple AD5170 Devices on One I2C Bus
LEVEL SHIFTING FOR BIDIRECTIONAL INTERFACE
While most legacy systems may be operated at one voltage, a
new component may be optimized at another. When two
systems operate the same signal at two different voltages, proper
level shifting is needed. For instance, one can use a 3.3 V
E2PROM to interface with a 5 V digital potentiometer. A level
shifting scheme is needed to enable a bidirectional
communication so that the setting of the digital potentiometer
can be stored to and retrieved from the E2PROM. Figure 16
shows one of the implementations. M1 and M2 can be any
N-channel signal FETs, or if VDD falls below 2.5 V, low threshold
FETs such as the FDV301N.
E2PROM AD5170
SDA1
SCL1
D
G
RPRP
3.3V 5V
S
M1
SCL2
SDA2
R
P
R
P
G
S
M2
VDD1 = 3.3V VDD2 =5V
D
Figure 16. Level Shifting for Operation at Different Potentials
ESD PROTECTION
All digital inputs are protected with a series input resistor and
parallel Zener ESD structures shown in Figure 17 and Figure 18.
This applies to the digital input pins SDA, SCL, and AD0.
LOGIC
340
V
SS
Figure 17. ESD Protection of Digital Pins
Rev. PrE 7/9/03 | Page 12 of 15
Preliminary Technical Data
AD5170
A,B,W
VSS
Figure 18. ESD Protection of Resistor Terminals
TERMINAL VOLTAGE OPERATING RANGE
The AD5172/73 VDD and GND power supply defines the
boundary conditions for proper 3-terminal digital
potentiometer operation. Supply signals present on terminals A,
B, and W that exceed VDD or GND will be clamped by the
internal forward biased diodes (see Figure 19).
A
V
D
D
B
W
V
SS
Figure 19. Maximum Terminal Voltages Set by VDD and VSS
POWER-UP SEQUENCE
Since the ESD protection diodes limit the voltage compliance at
terminals A, B, and W (see Figure 19), it is important to power
VDD/GND before applying any voltage to terminals A, B, and W;
otherwise, the diode will be forward biased such that VDD will be
powered unintentionally and may affect the rest of the user’s
circuit. The ideal power-up sequence is in the following order:
GND, VDD, digital inputs, and then VA/B/W. The relative order of
powering VA, VB, VW, and the digital inputs is not important as
long as they are powered after VDD/GND.
POWER SUPPLY CONSIDERATIONS
AD5170 employs fuse link technology, which requires an
adequate current density to blow the internal fuses to achieve a
given setting. As a result, the power supply, either an on-board
linear regulator or rack-mount power supply, must be rated at
5V with less than ±5% tolerance. The supply should be able to
handle 100mA of transient current, which lasts about 400 ms
during the one-time programming. A low ESR 1uF to 10uF
tantalum or electrolytic bypass capacitor should be applied to
VDD to minimize the transient disturbances during the
programming as shown. Once the programming is completed,
the supply voltage can be reduced to 2.7V with a supply current
as low as 1uA.
For users who have an on-board 3V supply for portable
applications, a separate 5V supply must be applied one time in
the factories for programming and a low VF Schotky Diode
should be designed with the AD5170 to isolate the supply
voltages. Once the programming is done, the 5V supply can be
removed and VDD reduced to 2.7V for minimum operation.
LAYOUT AND POWER SUPPLY BYPASSING
It is a good practice to employ compact, minimum lead length
layout design. The leads to the inputs should be as direct as
possible with a minimum conductor length. Ground paths
should have low resistance and low inductance.
Similarly, it is also a good practice to bypass the power supplies
with quality capacitors for optimum stability. Supply leads to the
device should be bypassed with disc or chip ceramic capacitors
of 0.01 µF to 0.1 µF. Low ESR 1 µF to 10 µF tantalum or
electrolytic capacitors should also be applied at the supplies to
minimize any transient disturbance and low frequency ripple
(see Figure 20). Note that the digital ground should also be
joined remotely to the analog ground at one point to minimize
the ground bounce.
AD5170
VDD
C1
C3
GND
10
µ
F0.1
µ
F
+
V
DD
Figure 20. Power Supply Bypassing
Rev. PrE 7/9/03 | Page 13 of 15
AD5170
Preliminary Technical Data
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PIN CONFIGURATION
BW
ANC
AD0
VDD SCL
SDA
8
7
6
5
4
3
2
1
9
10
GND
AD1
Figure 21.- Pin Configuration
Table 10. Pin Configuration
Pin Name Description
1 B B Terminal.
2 A A Terminal.
3 AD0 Programmable address bit 0 for multiple
package decoding.
4 GND Digital Ground.
5 VDD Positive Power Supply..
6 SCL Serial Clock Input. Positive edge triggered.
7 SDA Serial Data Input/Output.
8 AD1 Programmable address bit 1 for multiple
package decoding.
9 NC No Connect.
10 W W Terminal.
Rev. PrE 7/9/03 | Page 14 of 15
Preliminary Technical Data
AD5170
OUTLINE DIMENSIONS
0.23
0.20
0.17 0.80
0.40
0.15
0.00
0.27
0.17
0.95
0.85
0.75
SEATING
PLANE
1.10 MAX
10 6
5
1
0.50 BSC
3.00 BSC
3
.00 BSC
4.90 BSC
PIN 1
COMPLIANT TO JEDEC STANDARDS MO-187BA
COPLANARITY
0.10
Figure 22. 10-Lead Mini Small Outline Package [MSOP]
(RM-10)
Dimensions shown in millimeters
ORDERING GUIDE
Model RAB (Ω) Temperature Package Description Package Option Branding
AD5170BRM2.5-R2 2.5k –40°C to +125°C MSOP-10 RM-10 D0Y
AD5170BRM2.5-RL7 2.5k –40°C to +125°C MSOP-10 RM-10 D0Y
AD5170BRM10-R2 10k –40°C to +125°C MSOP-10 RM-10 D0Z
AD5170BRM10-RL7 10k –40°C to +125°C MSOP-10 RM-10 D0Z
AD5170BRM50-R2 50k –40°C to +125°C MSOP-10 RM-10 D0W
AD5170BRM50-RL7 50k –40°C to +125°C MSOP-10 RM-10 D0W
AD5170BRM100-R2 100k –40°C to +125°C MSOP-10 RM-10 D0X
AD5170BRM100-RL7 100k –40°C to +125°C MSOP-10 RM-10 D0X
AD5170EVAL See Note 1 Evaluation Board
1The evaluation board is shipped with the 10 kΩ RAB resistor option; however, the board is compatible with all available resistor value options.
The AD5170 contains 2532 transistors. Die size: 30.7 mil × 76.8 mil = 2,358 sq. mil.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. PrE 7/9/03 | Page 15 of 15