LMR14203 www.ti.com SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 LMR14203 SIMPLE SWITCHER(R) 42Vin, 0.3A Step-Down Voltage Regulator in SOT-23 Check for Samples: LMR14203 FEATURES DESCRIPTION * * * * * * * * * * The LMR14203 is a PWM DC/DC buck (step-down) regulator. With a wide input range from 4.5V-42V, it is suitable for a wide range of applications such as power conditioning from unregulated sources. They feature a low RDSON (0.9 typical) internal switch for maximum efficiency (85% typical). Operating frequency is fixed at 1.25 MHz allowing the use of small external components while still being able to have low output voltage ripple. Soft-start can be implemented using the shutdown pin with an external RC circuit allowing the user to tailor the soft-start time to a specific application. 1 2 Input Voltage Range of 4.5V to 42V Output Voltage Range of 0.765V to 34V Output Current up to 0.3A 1.25 MHz Switching Frequency Low Shutdown Iq, 16 A Typical Short Circuit Protected Internally Compensated Soft-Start Function Thin SOT-23-6 Package (2.97 x 1.65 x 1mm) Fully Enabled for WEBENCH(R) Power Designer PERFORMANCE BENEFITS * * * Tight Accuracy for Powering Digital ICs Extremely Easy to Use Tiny Overall Solution Reduces System Cost The LMR14203 is optimized for up to 300 mA load current. Additional features include: thermal shutdown, VIN under-voltage lockout, and gate drive under-voltage lockout. The LMR14203 is available in a low profile SOT-6L package. APPLICATIONS * * * * * * Point-of-Load Conversions from 5V, 12V, and 24V Rails Space Constrained Applications Battery Powered Equipment Industrial Distributed Power Applications Power Meters Portable Hand-Held Instruments System Performance Efficiency vs Load Current VIN = 24V, VOUT = 1.2V and 3.3V 100 100 90 90 80 80 EFFICIENCY (%) EFFICIENCY (%) Efficiency vs Load Current VIN = 12V, VOUT = 1.2V and 3.3V 70 60 50 40 30 20 10 0 0.00 70 60 50 40 30 20 10 1.2Vout 3.3Vout 0.05 0.10 0.15 0.20 0.25 LOAD CURRENT (A) 0 0.30 0.00 1.2Vout 3.3Vout 0.05 0.10 0.15 0.20 0.25 LOAD CURRENT (A) 0.30 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2011-2013, Texas Instruments Incorporated LMR14203 SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 www.ti.com CBOOT L1 VOUT LMR14203 VIN VIN CB SHDN SW GND FB D1 R1 R2 CIN COUT Connection Diagram Top View LMR14203 CB 1 GND 2 FB 3 PIN 1 ID 6 SW 5 VIN 4 SHDN Figure 1. 6 Lead SOT Package See Package Number DDC0006A Pin Descriptions Pin Name Function 1 CB 2 GND SW FET gate bias voltage. Connect CBOOT cap between CB and SW. 3 FB 4 SHDN 5 VIN Power input voltage pin: 4.5V to 42V normal operating range. 6 SW Power FET output: Connect to inductor, diode, and CBOOT cap. Ground connection. Feedback pin: Set feedback voltage divider ratio with VOUT = VFB (1+(R1/R2)). Resistors should be in the 100-10K range to avoid input bias errors. Logic level shutdown input. Pull to GND to disable the device and pull high to enable the device. If this function is not used tie to VIN or leave open. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 LMR14203 www.ti.com SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 Absolute Maximum Ratings (1) (2) VIN -0.3V to +45V SHDN -0.3V to (VIN+0.3V) <45V SW Voltage -0.3V to +45V CB Voltage above SW Voltage 7V FB Voltage -0.3V to +5V Maximum Junction Temperature 150C Power Dissipation (3) Internally Limited For soldering specifications:http://www.ti.com/lit/SNOA549 ESD Susceptibility (4) Human Body Model (1) (2) (3) (4) 1.5 kV Absolute maximum ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is intended to be functional, but device parameter specifications may not be ensured. For ensured specifications and test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, JA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using: PD (MAX) = (TJ(MAX) - TA)/JA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ=175C (typ.) and disengages at TJ=155C (typ). Human Body Model, applicable std. JESD22-A114-C. Operating Conditions Operating Junction Temperature Range (1) -40C to +125C Storage Temperature -65C to +150C Input Voltage VIN 4.5V to 42V SW Voltage (1) Up to 42V All limits specified at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are 100% production tested. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 3 LMR14203 SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 www.ti.com Electrical Characteristics Specifications in standard type face are for TJ = 25C and those with boldface type apply over the full Operating Temperature Range ( TJ = -40C to +125C). Minimum and Maximum limits are ensured through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = +25C, and are provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 12V. Parameter IQ Quiescent current Test Conditions SHDN = 0V Device On, No Load 1.35 1.85 0.9 1.6 0.0 0.5 A (3) Switch leakage current VIN = 42V ICL Switch current limit See (4) See (5) tMIN Minimum ON time fSW Switching frequency DMAX Maximum duty cycle VUVP Undervoltage lockout thresholds 525 0.747 VFB = 0.5V 0.95 ISHDN Shutdown threshold Shutdown pin input bias current 0.1 1.0 0.765 0.782 VFB = 0V On threshold Device on 1.25 81 87 3.7 3.5 2.3 A V ns 1.50 0.35 4.4 mA mA 100 Off threshold VSHDN A 40 1.75 ILSW FB Pin reference voltage Units 16 See Feedback pin bias current Max (1) 1.30 Switch ON resistance VFB Typ (2) Device On, Not Switching RDSON IFB Min (1) MHz % 3.25 1.0 Device off 0.9 0.3 VSHDN = 2.3V (5) 0.05 1.5 VSHDN = 0V 0.02 1.5 V V A THERMAL SPECIFICATIONS RJA (1) (2) (3) (4) (5) (6) 4 Junction-to-Ambient Thermal Resistance, SOT-6L Package See (6) 121 C/W All limits specified at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are 100% production tested. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Typical numbers are at 25C and represent the most likely norm. Includes the bond wires, RDSON from VIN pin to SW pin. Current limit at 0% duty cycle. Bias currents flow into pin. All numbers apply for packages soldered directly onto a 3" x 3" PC board with 2 oz. copper on 4 layers in still air in accordance to JEDEC standards. Thermal resistance varies greatly with layout, copper thickness, number of layers in PCB, power distribution, number of thermal vias, board size, ambient temperature, and air flow. Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 LMR14203 www.ti.com SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 Typical Performance Characteristics Efficiency vs. Load Current (VOUT = 3.3V) Input UVLO Voltage vs. Temperature 100 VIN = 12V EFFICIENCY (%) 80 VIN = 36V 60 VIN = 24V 40 20 0 0.0 0.1 0.2 0.3 LOAD CURRENT (A) Figure 2. Figure 3. Switch Current Limit vs. SHDN Pin Voltage (Soft-start Implementation) SHDN Pin Current vs. SHDN Pin Voltage SWITCH CURRENT LIMIT (mA) 800 600 400 200 0 1.0 1.6 2.2 2.8 3.4 4.0 SHDN PIN VOLTAGE (V) Figure 4. Figure 5. Switching Node and Output Voltage Waveforms VIN = 12V, VOUT = 3.3V, IOUT = 200 mA Top trace: VOUT, 10 mV/div, AC Coupled Bottom trace: SW, 5V/div, DC Coupled T = 1 s/div Figure 6. Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 5 LMR14203 SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) Load Transient Waveforms Start-Up Waveform VIN = 12V, VOUT = 3.3V, IOUT = 300 mA to 200 mA to 300 mA Top trace: VOUT, 20 mV/div, AC Coupled Bottom trace: IOUT, 100 mA/div, DC Coupled T = 200 s/div Figure 7. VIN = 12V, VOUT = 3.3V, IOUT = 50 mA Top trace: VOUT, 1V/div, DC Coupled Bottom trace: SHDN, 2V/div, DC Coupled T = 40 s/div Figure 8. Block Diagram CB + + OSC SET FB + PWM Comp Error Amp + Bandgap Soft Start VIN Max Duty Cycle Limit RESET Inductor Current Measurement DC LIMIT BUCK DRIVE FET Driver SW UVLO TSD UVLO Comp Thermal Shutdown BG Voltage Regulator GND SHDN 6 Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 LMR14203 www.ti.com SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 APPLICATION INFORMATION Protection The LMR14203 has dedicated protection circuitry running during normal operation to protect the IC. The thermal shutdown circuitry turns off the power device when the die temperature reaches excessive levels. The UVLO comparator protects the power device during supply power startup and shutdown to prevent operation at voltages less than the minimum input voltage. A gate drive (CB) under-voltage lockout is included to ensure that there is enough gate drive voltage to drive the MOSFET before the device tries to start switching. The LMR14203 also features a shutdown mode decreasing the supply current to approximately 16 A. Continuous Conduction Mode The LMR14203 contains a current-mode, PWM buck regulator. A buck regulator steps the input voltage down to a lower output voltage. In continuous conduction mode (when the inductor current never reaches zero at steady state), the buck regulator operates in two cycles. The power switch is connected between VIN and SW. In the first cycle of operation the transistor is closed and the diode is reverse biased. Energy is collected in the inductor and the load current is supplied by COUT and the rising current through the inductor. During the second cycle the transistor is open and the diode is forward biased due to the fact that the inductor current cannot instantaneously change direction. The energy stored in the inductor is transferred to the load and output capacitor. The ratio of these two cycles determines the output voltage. The output voltage is defined approximately as: D=VOUT/VIN and D' = (1-D) where * D is the duty cycle of the switch. (1) D and D' will be required for design calculations. Design Procedure This section presents guidelines for selecting external components. Setting the Output Voltage The output voltage is set using the feedback pin and a resistor divider connected to the output as shown on the front page schematic. The feedback pin voltage is 0.765V, so the ratio of the feedback resistors sets the output voltage according to the following equation: VOUT=0.765V(1+(R1/R2)) (2) Typically R2 will be given as 100-10 k for a starting value. To solve for R1 given R2 and VOUT use R1=R2((VOUT/0.765V)-1). Input Capacitor A low ESR ceramic capacitor (CIN) is needed between the VIN pin and GND pin. This capacitor prevents large voltage transients from appearing at the input. Use a 2.2 F-10 F value with X5R or X7R dielectric. Depending on construction, a ceramic capacitor's value can decrease up to 50% of its nominal value when rated voltage is applied. Consult with the capacitor manufacturer's data sheet for information on capacitor derating over voltage and temperature. Inductor Selection The most critical parameters for the inductor are the inductance, peak current, and the DC resistance. The inductance is related to the peak-to-peak inductor ripple current, the input and the output voltages. (VIN - VOUT)VOUT L= VIN x IRIPPLE x fSW (3) A higher value of ripple current reduces inductance, but increases the conductance loss, core loss, and current stress for the inductor and switch devices. It also requires a bigger output capacitor for the same output voltage ripple requirement. A reasonable value is setting the ripple current to be 30% of the DC output current. Since the ripple current increases with the input voltage, the maximum input voltage is always used to determine the inductance. The DC resistance of the inductor is a key parameter for the efficiency. Lower DC resistance is Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 7 LMR14203 SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 www.ti.com available with a bigger winding area. A good tradeoff between the efficiency and the core size is letting the inductor copper loss equal 2% of the output power. See AN-1197 SNVA038 for more information on selecting inductors. A good starting point for most applications is a 10 H to 22 H with a 0.7A or greater current rating for the LMR14203. Using such a rating will enable the LMR14203 to current limit without saturating the inductor. This is preferable to the device going into thermal shutdown mode and the possibility of damaging the inductor if the output is shorted to ground or other longterm overload. Output Capacitor The selection of COUT is driven by the maximum allowable output voltage ripple. The output ripple in the constant frequency, PWM mode is approximated by: VRIPPLE = IRIPPLE(ESR+(1/(8fSWCOUT))) (4) The ESR term usually plays the dominant role in determining the voltage ripple. Low ESR ceramic capacitors are recommended. Capacitors in the range of 22 F-100 F are a good starting point with an ESR of 0.1 or less. Bootstrap Capacitor A 0.15 F ceramic capacitor or larger is recommended for the bootstrap capacitor (CBOOT). For applications where the input voltage is less than twice the output voltage a larger capacitor is recommended, generally 0.15 F to 1 F to ensure plenty of gate drive for the internal switches and a consistently low RDSON. Soft-Start Components The LMR14203 has circuitry that is used in conjunction with the SHDN pin to limit the inrush current on start-up of the DC/DC switching regulator. The SHDN pin in conjunction with a RC filter is used to tailor the soft-start for a specific application. When a voltage applied to the SHDN pin is between 0V and up to 2.3V it will cause the cycle by cycle current limit in the power stage to be modulated for minimum current limit at 0V up to the rated current limit at 2.3V. Thus controlling the output rise time and inrush current at startup. The resistor value should be selected so the current sourced into the SHDN pin will be greater then the leakage current of the SHDN pin (1.5 A ) when the voltage at SHDN is equal or greater then 2.3V. Shutdown Operation The SHDN pin of the LMR14203 is designed so that it may be controlled using 2.3V or higher logic signals. If the shutdown function is not to be used the SHDN pin may be tied to VIN. The maximum voltage to the SHDN pin should not exceed 42V. If the use of a higher voltage is desired due to system or other constraints it may be used, however a 100 k or larger resistor is recommended between the applied voltage and the SHDN pin to protect the device. SCHOTTKY Diode The breakdown voltage rating of the diode (D1) is preferred to be 25% higher than the maximum input voltage. The current rating for the diode should be equal to the maximum output current for best reliability in most applications. In cases where the duty cycle is greater than 50%, the average diode current is lower. In this case it is possible to use a diode with a lower average current rating, approximately (1-D)IOUT, however the peak current rating should be higher than the maximum load current. A 0.5A to 1A rated diode is a good starting point. Layout Considerations To reduce problems with conducted noise pick up, the ground side of the feedback network should be connected directly to the GND pin with its own connection. The feedback network, resistors R1 and R2, should be kept close to the FB pin, and away from the inductor to minimize coupling noise into the feedback pin. The input bypass capacitor CIN must be placed close to the VIN pin. This will reduce copper trace resistance which effects input voltage ripple of the IC. The inductor L1 should be placed close to the SW pin to reduce EMI and capacitive coupling. The output capacitor, COUT should be placed close to the junction of L1 and the diode D1. The L1, D1, and COUT trace should be as short as possible to reduce conducted and radiated noise and increase overall efficiency. The ground connection for the diode, CIN, and COUT should be as small as possible and tied to the system ground plane in only one spot (preferably at the COUT ground point) to minimize conducted noise in the system ground plane. For more detail on switching power supply layout considerations see Application Note AN1149: Layout Guidelines for Switching Power Supplies SNVA021. 8 Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 LMR14203 www.ti.com SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 Typical Applications C BOOT LMR14203 L1 15 PH 3.3V OUT 0.15 PF 4.5V to 42V IN VIN CB SHDN SW GND FB D1 60V 500 mA R1 3.4k R2 1.02k CIN 2.2 PF COUT 47 PF Figure 9. Application Circuit, 3.3V Output L1 15 PH CBOOT LMR14203 5V OUT 0.15 PF 7V to 42V IN VIN CB SHDN SW GND FB D1 60V 500 mA R1 5.62k R2 1.02k CIN 2.2 PF COUT 47 PF Figure 10. Application Circuit, 5V Output L1 47 PH CBOOT LMR14203 15V to 42V IN 12V OUT 0.15 PF VIN CB SHDN SW GND FB D1 60V 500 mA R1 14.7k R2 1k CIN 2.2 PF COUT 22 PF Figure 11. Application Circuit, 12V Output Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 9 LMR14203 SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 www.ti.com L1 47 PH CBOOT LMR14203 0.15 PF 18V to 42V IN VIN CB SHDN SW GND FB 15V OUT D1 60V 500 mA R1 28k R2 1.5k CIN 2.2 PF COUT 22 PF Figure 12. Application Circuit, 15V Output L1 10 PH CBOOT LMR14203 4.5V to 12V IN 0.8V OUT 0.15 PF VIN CB SHDN SW GND FB D1 60V 500 mA R1 30.9 CIN 2.2 PF R2 787 COUT 100 PF Figure 13. Application Circuit, 0.8V Output 10 Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 LMR14203 www.ti.com SNVS732C - OCTOBER 2011 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision B (April 2013) to Revision C * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 10 Submit Documentation Feedback Copyright (c) 2011-2013, Texas Instruments Incorporated Product Folder Links: LMR14203 11 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) (6) LMR14203XMK/NOPB ACTIVE SOT-23-THIN DDC 6 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 SJ3B LMR14203XMKE/NOPB ACTIVE SOT-23-THIN DDC 6 250 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 SJ3B LMR14203XMKX/NOPB ACTIVE SOT-23-THIN DDC 6 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 SJ3B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 3-Mar-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LMR14203XMK/NOPB SOT23-THIN DDC 6 1000 178.0 8.4 LMR14203XMKE/NOPB SOT23-THIN DDC 6 250 178.0 LMR14203XMKX/NOPB SOT23-THIN DDC 6 3000 178.0 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 3-Mar-2017 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMR14203XMK/NOPB SOT-23-THIN DDC 6 1000 210.0 185.0 35.0 LMR14203XMKE/NOPB SOT-23-THIN DDC 6 250 210.0 185.0 35.0 LMR14203XMKX/NOPB SOT-23-THIN DDC 6 3000 210.0 185.0 35.0 Pack Materials-Page 2 PACKAGE OUTLINE DDC0006A SOT - 1.1 max height SCALE 4.000 SOT 3.05 2.55 1.75 1.45 PIN 1 INDEX AREA 1.100 0.847 B 1 0.1 C A 6 4X 0.95 3.05 2.75 1.9 4 3 0.5 0.3 0.2 0.1 TYP 0.0 6X C 0 -8 TYP 0.20 TYP 0.12 C A B SEATING PLANE 0.6 TYP 0.3 0.25 GAGE PLANE 4214841/B 11/2020 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Reference JEDEC MO-193. www.ti.com EXAMPLE BOARD LAYOUT DDC0006A SOT - 1.1 max height SOT SYMM 6X (1.1) 1 6 6X (0.6) SYMM 4X (0.95) 4 3 (R0.05) TYP (2.7) LAND PATTERN EXAMPLE EXPLOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL UNDER SOLDER MASK METAL SOLDER MASK OPENING EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED SOLDER MASK DEFINED SOLDERMASK DETAILS 4214841/B 11/2020 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DDC0006A SOT - 1.1 max height SOT SYMM 6X (1.1) 1 6 6X (0.6) SYMM 4X(0.95) 4 3 (R0.05) TYP (2.7) SOLDER PASTE EXAMPLE BASED ON 0.125 THICK STENCIL SCALE:15X 4214841/B 11/2020 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES "AS IS" AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI's products are provided subject to TI's Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI's provision of these resources does not expand or otherwise alter TI's applicable warranties or warranty disclaimers for TI products. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2020, Texas Instruments Incorporated