This model consists of a 15” bass loudspeaker and a 2” compression driver that is concentrically mounted using the same magnetic structure.
The bass unit features a 4”1/2 voice coil, attached to a double suspension system. The high frequency drives features a 4” titanium diaphragm and
an edgewound ribbon voice coil. This unit has incredible power capacity, high efficiency, smooth response and low distortion.
Este modelo consta de una unidad de gra ves de 15” y de un r epr oductor de agudos de 2” montados concéntricamente uno sobr e otr o compartiendo
el mismo motor. La bobina de graves es de 4”1/2 y va sujeta a un sistema de suspensión doble, mientras que el diafragma de agudos, de titanio,
utiliza una bobina de 4” de hilo plano de aluminio. Este transductor tiene una capacidad de potencia muy importante, una elevada eficiencia y
respuesta muy homogenea con reducida distorsión.
-Pro-
PREDICTED LOW FREQUENCY RESPONSE • Bass-reflex cabinet, Vb=90.00 I, fb=40.0 Hz
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Measured with FD 212, with EQ & -3 dB ATT.
FREQUENCY RESPONSE, PHASE, On axis, 1w @ 1m. L.F. UNIT
FREE AIR IMPEDANCE CURVE, L.F. UNIT
FREQUENCY RESPONSE, PHASE On axis, 1w @ 1m. H.F. UNIT
15DX
CO AXIAL
SPECIFICATIONS
L.F. UNIT
Nominal diameter
Rated impedance
Power capacity*
Program Power
Sensitivity
Frequency range
Recom. enclosure vol.
Voice coil diameter
Magnetic assembly weight
BL factor
Moving mass
Voice coil length
Air gap height
X damage
Voice Coil Inductance, Le@ 1kHz
H.F. UNIT
Rated impedance
Minimum impedance
Power capacity
Frequency range
Sensitivity 1w @ 1m
Voice coil diameter
Flux density
BL factor
Dispersion
380 mm. 15 in.
8 ohms.
350 w RMS
700 Watts.
97 dB 2.83v @ 1m @ 2π
35-1500 Hz
60/180 l 2.14/6.35 ft.3
114 mm. 4.5 in.
9.4 kg. 20.68 lb.
16.6 N/A
0.11 kg.
17 mm.
9 mm.
28 mm.
1.5 mH
8 ohms.
6.3 ohm@ 1kHz
100 w
0.8 - 17 kHz
103 dB
100 mm. 4 in.
1.5 T
12.85 N/A
90°
MOUNTING INFORMATION
388 mm. 15.28 in.
370 mm. 14.57 in.
352 mm. 13.86 in.
355 mm. 13.98 in.
178 mm. 7 in.
7 l 0.25 ft.3
11.3 kg. 24.86 lb.
12.5 kg. 25 lb.
Overall diameter
Bolt circle diameter
Baffle cutout diameter:
-Front mount
-Rear mount
Depth
Volume displaced by driver
Net weight
Shipping weight
MATERIALS
L.F. UNIT
Basket
Cone
Surround
Voice coil
Magnet
H.F. UNIT
Diaphragm
Voice coil
Voice coil former
Die cast aluminium
Paper
Plasticised cloth
Edgewound copper ribbon
Ferrite
Titanium
Edgewound alum. ribbon
Kapton
THIELE-SMALL PARAMETERS**
Resonant Frequency, fs
D.C. Voice Coil Resistance, Re
Mechanical Quality Factor, Qms
Electrical Quality Factor, Qes
Total Quality Factor, Qts
Equivalent Air Volume to Cms, Vas
Mechanical Compliance, Cms
Mechanical Resistance, Rms
Efficiency, o (%)
Effective Surface Area, Sd(m2)
Maximum Displacement, Xmax
Displacement Volume, Vd
40 Hz
5.3 ohms.
9.2
0.45
0.43
160 l
145 µm/N
4 kg/s
2.4
0.088 m2
4 mm.
350 cm.3
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at least two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
** T-S parameters are measured after an exercise period using a
preconditioning power test, using a velocity-current laser transducer,
and will reflect the long term parameters, once the loudspeaker has
been working for a short period of time.
NOTAS
*La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada.
Por potencia programa se entiende la capacidad del altavoz en el
manejo de señales transitorias, como sería el proporcionado por el
contenido de un pasaje musical normal.
* *Los parámetros T-S han sido medidos después de un periodo de
fatiga y estabilización de las suspensiones, mediante transductor laser
de velocidad-corriente, y son el reflejo de los parámetros a largo plazo
del altavoz, una vez éste haya sido instalado y haya trabajado en un
corto espacio de tiempo.
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
L.F. UNIT
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
H.F. UNIT
- 25 -
SPECIFICATIONS
L.F. UNIT
Nominal diameter
Rated impedance
Power capacity*
Program Power
Sensitivity
Frequency range
Recom. enclosure vol.
Voice coil diameter
Magnetic assembly weight
BL factor
Moving mass
Voice coil length
Air gap height
X damage
Voice Coil Inductance, Le@ 1kHz
H.F. UNIT
Rated impedance
Minimum impedance
Power capacity
Frequency range
Sensitivity 1w @ 1m
Voice coil diameter
Flux density
BL factor
Dispersion
380 mm. 15 in.
8 ohms.
250 w RMS
500 Watts.
99 dB 2.83v @ 1m @ 2π
25-3000 Hz
60/150 l 2.14/5.59 ft.3
77 mm. 3 in.
6.4 kg. 14.11 lb.
14.5 N/A
0.070 kg.
13 mm.
8 mm.
28 mm.
1 mH
8 ohms.
6.5 ohm@ 1kHz
80 w
0.8 - 17 kHz
105 dB
72.2 mm. 2.8 in.
1.4 T
7.5 N/A
90°
MOUNTING INFORMATION
388 mm. 15.28 in.
370 mm. 14.57 in.
352 mm. 13.85 in.
355 mm. 13.98 in.
180 mm. 7.1 in.
7 l 0.25 ft.3
8.25 kg. 18.19 lb.
9.25 kg. 20.4 lb.
Overall diameter
Bolt circle diameter
Baffle cutout diameter:
-Front mount
-Rear mount
Depth
Volume displaced by driver
Net weight
Shipping weight
MATERIALS
L.F. UNIT
Basket
Cone
Surround
Voice coil
Magnet
H.F. UNIT
Diaphragm
Voice coil
Voice coil former
Cast aluminium
Paper
Plasticised cloth
Edgewound alum. ribbon
Ferrite
Titanium
Edgewound alum. ribbon
Kapton
THIELE-SMALL PARAMETERS**
Resonant Frequency, fs
D.C. Voice Coil Resistance, Re
Mechanical Quality Factor, Qms
Electrical Quality Factor, Qes
Total Quality Factor, Qts
Equivalent Air Volume to Cms, Vas
Mechanical Compliance, Cms
Mechanical Resistance, Rms
Efficiency, o (%)
Effective Surface Area, Sd(m2)
Maximum Displacement, Xmax
Displacement Volume, Vd
45 Hz
5.68 ohms.
11.4
0.519
0.496
203 l
188.4 µm/N
1.69 kg/s
3.18
0.088 m2
3.5 mm.
300 cm.3
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at least two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
** T-S parameters are measured after an exercise period using a
preconditioning power test, using a velocity-current laser transducer,
and will reflect the long term parameters, once the loudspeaker has
been working for a short period of time.
NOTAS
*La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada.
Por potencia programa se entiende la capacidad del altavoz en el
manejo de señales transitorias, como sería el proporcionado por el
contenido de un pasaje musical normal.
* *Los parámetros T-S han sido medidos después de un periodo de
fatiga y estabilización de las suspensiones, mediante transductor laser
de velocidad-corriente, y son el reflejo de los parámetros a largo plazo
del altavoz, una vez éste haya sido instalado y haya trabajado en un
corto espacio de tiempo.
This dual loudspeaker incorporates a 15” bass transducer, f eaturing a 3” voice coil diameter, edgew ound aluminium ribbon wir e, and a concentrically
mounted 2” compression driver into an integrated voice coil gap magnet system. This design achieves high efficiency, smooth frequency response,
low distortion, reduces phasing problems in the crossover region, and simplifies enclosure design.
15KX
CO AXIAL
Sistema coaxial de 15” con bobina de 3" de diámetro, y motor de compresión de 2” con diafragma de titanio y bobina de 3”.Montados de forma
concéntrica, son movidos por el mismo circuito magnético. La asimilación de los focos de emisión a una fuente puntual reduce de forma notable
los problemas de fase en la zona de transición entre ambos reproductores confiriendo una respuesta muy coherente. Muy recomendado para
aplicaciones en sistemas bass-reflex de tamaño compacto.
-Pro-
PREDICTED LOW FREQUENCY RESPONSE • Bass-reflex cabinet, Vb=90.00 I, fb=40.0 Hz
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Measured with FD 212, with EQ & -3 dB ATT.
FREQUENCY RESPONSE, PHASE, On axis, 1w @ 1m. L.F. UNIT
FREE AIR IMPEDANCE CURVE, L.F. UNIT
FREQUENCY RESPONSE, PHASE On axis, 1w @ 1m. H.F. UNIT
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
L.F. UNIT
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
H.F. UNIT
- 26 -
This dual loudspeaker includes, in a single unit, a 12” bass driver and a concentrically mounted compression tweeter. This provides a single point
source and reduces phasing problems in the crossover region. The bass driver features a 2” (52 mm) voice coil diameter, attached to a lighweight
curvilinear cone, and shows a smoothly extended frequency response up to 7 kHz. The tweeter has excellent efficiency and fast response to
transient attacks.
12CX
CO AXIAL
Modelo de 12" que incluye 2 unidades, una de graves para la reproducción de media y baja frecuencia y otra de compresión para alta frecuencia
que van montadas concéntricamente y radian de forma puntual, lo que evita problemas de rotación de fase en la zona de transición entre ambos
reproductores garantizando una respuesta coherente y de gran calidad.
SPECIFICATIONS
-Pro-
L.F. UNIT
Nominal diameter
Rated impedance
Power capacity*
Program Power
Sensitivity
Frequency range
Recom. enclosure vol.
Voice coil diameter
Magnetic assembly weight
BL factor
Moving mass
Voice coil length
Air gap height
X damage
Voice Coil Inductance, Le@ 1kHz
H.F. UNIT
Rated impedance
Minimum impedance
Power capacity
Frequency range
Sensitivity 1w @ 1m
Voice coil diameter
Flux density
BL factor
Dispersion
300 mm. 12 in.
8 ohms.
100 w RMS
200 Watts.
98 dB 2.83v @ 1m @ 2π
45-7000 Hz
30/100 l 1.06/3.53 ft.3
52 mm. 2 in.
3.85 kg. 8.5 lb.
13 N/A
0.039 kg.
11 mm.
7 mm.
16 mm.
0.7 mH
8 ohms.
8.2 ohm@ 7kHz
15 w
3.5 - 20 kHz
104 dB
25.8 mm. 1 in.
1.45 T
4 N/A
90°
MOUNTING INFORMATION
320 mm. 12.6 in.
299 mm. 11.77 in.
286 mm. 11.26 in.
280 mm. 11.02 in.
157 mm. 6.18 in.
5.5 l 0.16 ft.3
5.26 kg. 11.57 lb.
5.9 kg. 13 lb.
Overall diameter
Bolt circle diameter
Baffle cutout diameter:
-Front mount
-Rear mount
Depth
Volume displaced by driver
Net weight
Shipping weight
MATERIALS
L.F. UNIT
Basket
Cone
Surround
Voice coil
Magnet
H.F. UNIT
Diaphragm
Voice coil
Voice coil former
Die cast aluminium
Paper
Plasticised cloth
Copper
Ferrite
Aluminium
Copper
Kapton
THIELE-SMALL PARAMETERS**
Resonant Frequency, fs
D.C. Voice Coil Resistance, Re
Mechanical Quality Factor, Qms
Electrical Quality Factor, Qes
Total Quality Factor, Qts
Equivalent Air Volume to Cms, Vas
Mechanical Compliance, Cms
Mechanical Resistance, Rms
Efficiency, o (%)
Effective Surface Area, Sd(m2)
Maximum Displacement, Xmax
Displacement Volume, Vd
42 Hz
6.22 ohms.
3.5
0.38
0.34
146.4 l
373 µm/N
2.91 kg/s
2.65
0.053 m2
2 mm.
106 cm.3
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at least two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
** T-S parameters are measured after an exercise period using a
preconditioning power test, using a velocity-current laser transducer,
and will reflect the long term parameters, once the loudspeaker has
been working for a short period of time.
NOTAS
*La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada.
Por potencia programa se entiende la capacidad del altavoz en el
manejo de señales transitorias, como sería el proporcionado por el
contenido de un pasaje musical normal.
* *Los parámetros T-S han sido medidos después de un periodo de
fatiga y estabilización de las suspensiones, mediante transductor laser
de velocidad-corriente, y son el reflejo de los parámetros a largo plazo
del altavoz, una vez éste haya sido instalado y haya trabajado en un
corto espacio de tiempo.
PREDICTED LOW FREQUENCY RESPONSE • Bass-reflex cabinet, Vb=50.00 I, fb=50.0 Hz
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Measured with FD 100, with EQ & -3 dB ATT.
FREQUENCY RESPONSE, PHASE, On axis, 1w @ 1m. L.F. UNIT
FREE AIR IMPEDANCE CURVE, L.F. UNIT
FREQUENCY RESPONSE, PHASE On axis, 1w @ 1m. H.F. UNIT
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
L.F. UNIT
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
H.F. UNIT
- 28 -
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Measured with FD 212, with EQ & -6 dB ATT.
FREQUENCY RESPONSE, PHASE, On axis, 1w @ 1m. L.F. UNIT
FREE AIR IMPEDANCE CURVE, L.F. UNIT
FREQUENCY RESPONSE, PHASE On axis, 1w @ 1m. H.F. UNIT
This dual loudspeaker incorporates a 12” bass transducer, featuring a 3” voice coil diameter, edgewound aluminium ribbon wire, and a concentrically
mounted 2” compression driver into an integrated voice coil gap magnet system. This design achieves high efficiency, smooth frequency response,
low distortion, reduces phasing problems in the crossover region, and simplifies enclosure design.
Sistema coaxial de 12” con bobina de 3” de diámetro y motor de compresión de 2” con diafragma de titanio y bobina de 3”. Montados de forma
concéntrica estan movidos por el mismo circuito magnético.
La asimilación de los focos de emisión a una fuente puntual reduce de forma notable los problemas de fase en la zona de transición entre ambos
reproductores confiriendo una respuesta muy coherente. Muy recomendado para aplicaciones en sistemas bass-reflex de tamaño compacto.
-Pro-
PREDICTED LOW FREQUENCY RESPONSE • Bass-reflex cabinet, Vb=60.00 I, fb=60.00 Hz
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
L.F. UNIT
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
H.F. UNIT
- 29 -
12KX
CO AXIAL
SPECIFICATIONS
L.F. UNIT
Nominal diameter
Rated impedance
Power capacity*
Program Power
Sensitivity
Frequency range
Recom. enclosure vol.
Voice coil diameter
Magnetic assembly weight
BL factor
Moving mass
Voice coil length
Air gap height
X damage
Voice Coil Inductance, Le@ 1kHz
H.F. UNIT
Rated impedance
Minimum impedance
Power capacity
Frequency range
Sensitivity 1w @ 1m
Voice coil diameter
Flux density
BL factor
Dispersion
300 mm. 12 in.
8 ohms.
250 w RMS
500 Watts
98 dB 2.83v @ 1m @ 2π
35-3000 Hz
40/100 l 1.49/3.53 ft.3
77 mm. 3 in.
6.4 kg. 14.11 lb.
14.5 N/A
0.045 kg.
13 mm.
8 mm.
30 mm.
1 mH
8 ohms.
11 ohm@ 1kHz
80 w
0.8 - 17 kHz
105 dB
72.2 mm. 2.8 in.
1.875 T
11 N/A
90°
MOUNTING INFORMATION
320 mm. 12.6 in.
300 mm. 11.8 in.
286 mm. 11.26 in.
280 mm. 11.02 in.
160 mm. 6.30 in.
7 l 0.25 ft.3
7.85 kg. 17.31 lb.
8.5 kg. 18.73 lb.
Overall diameter
Bolt circle diameter
Baffle cutout diameter:
-Front mount
-Rear mount
Depth
Volume displaced by driver
Net weight
Shipping weight
MATERIALS
L.F. UNIT
Basket
Cone
Surround
Voice coil
Magnet
H.F. UNIT
Diaphragm
Voice coil
Voice coil former
Cast aluminium
Paper
Plasticised cloth
Edgewound alum. ribbon
Ferrite
Titanium
Edgewound alum. ribbon
Kapton
THIELE-SMALL PARAMETERS**
Resonant Frequency, fs
D.C. Voice Coil Resistance, Re
Mechanical Quality Factor, Qms
Electrical Quality Factor, Qes
Total Quality Factor, Qts
Equivalent Air Volume to Cms, Vas
Mechanical Compliance, Cms
Mechanical Resistance, Rms
Efficiency, o (%)
Effective Surface Area, Sd(m2)
Maximum Displacement, XmaX
Displacement Volume, Vd
45 Hz
5.6 ohms.
10.4
0.380
0.370
70 l
186 µm/N
1.49 kg/s
2.9
0.055 m2
3.5 mm.
200 cm.3
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at least two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
** T-S parameters are measured after an exercise period using a
preconditioning power test, using a velocity-current laser transducer,
and will reflect the long term parameters, once the loudspeaker has
been working for a short period of time.
NOTAS
*La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada.
Por potencia programa se entiende la capacidad del altavoz en el
manejo de señales transitorias, como sería el proporcionado por el
contenido de un pasaje musical normal.
* *Los parámetros T-S han sido medidos después de un periodo de
fatiga y estabilización de las suspensiones, mediante transductor laser
de velocidad-corriente, y son el reflejo de los parámetros a largo plazo
del altavoz, una vez éste haya sido instalado y haya trabajado en un
corto espacio de tiempo.
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
Measured with FD 102, with EQ & -3 dB ATT.
FREQUENCY RESPONSE, PHASE, On axis, 1w @ 1m. L.F. UNIT
FREE AIR IMPEDANCE CURVE, L.F. UNIT
FREQUENCY RESPONSE, PHASE On axis, 1w @ 1m. H.F. UNIT
This loudspeaker is a single unit, two-way system, comprising of an 8” bass driver and a concentrically mounted tweeter. This provides a single
point source and reduces phasing problems in the crossover region. The bass unit features a 1”3/4 (40mm) voice coil attached to a pol ypropylene
cone and copper ring on the pole piece. This provides a smoothly extended frequency response up to 7 kHz, with reduced harmonic distortion.
The compression tweeter shows excellent efficiency and fast response to transient attacks.
Este alta voz de 8” se compone de 2 unidades montadas de forma concéntrica pr oporcionando una cobertura total del espectro audible. La unidad
de graves utiliza un cono de polipropileno sujeto a una suspensión de goma y movido por una bobina de 1"1/2 realizada con hilo de aluminio, lo
que proporciona una respuesta en graves y medios sorprendentemente natural con una banda pasante excepcional. La unidad de agudos utiliza
un modelo de comprensión con diafragma y bobinado de aluminio que le confiere un elevado rendimiento y una respuesta transitoria exquisita.
Esta combinación ofrece unos resultados espectaculares de naturalidad, dinámica y fidelidad.
-Pro-
PREDICTED LOW FREQUENCY RESPONSE • Bass-reflex cabinet, Vb=30.00 I, fb=50.0 Hz
8BX
CO AXIAL
SPECIFICATIONS
L.F. UNIT
Nominal diameter
Rated impedance
Power capacity*
Program Power
Sensitivity
Frequency range
Recom. enclosure vol.
Voice coil diameter
Magnetic assembly weight
BL factor
Moving mass
Voice coil length
Air gap height
X damage
Voice Coil Inductance, Le@ 1kHz
H.F. UNIT
Rated impedance
Minimum impedance
Power capacity
Frequency range
Sensitivity 1w @ 1m
Voice coil diameter
Flux density
BL factor
Dispersion
200 mm. 8 in.
8 ohms.
100 w RMS
200 Watts.
92 dB 2.83v @ 1m @ 2π
25-8000 Hz
20/60 l 0.746/2.24 ft.3
38.5 mm. 1 1/2 in.
2 kg. 4.4 lb.
7.3 N/A
0.023 kg.
14 mm.
61 mm.
20 mm.
0.2 mH
8 ohms.
6 ohm@ 4kHz
15 w
3/20 kHz
102 dB
26 mm. 1 in.
1.4 T
4 N/A
90°
MOUNTING INFORMATION
215 mm. 8.46 in.
200 mm. 7.9 in.
182 mm. 7.16 in.
185 mm. 7.3in.
120 mm. 4.72 in.
1.5 l 0.056 ft.3
2.9 kg. 6.39 lb.
3.1 kg. 6.83 lb.
Overall diameter
Bolt circle diameter
Baffle cutout diameter:
-Front mount
-Rear mount
Depth
Volume displaced by driver
Net weight
Shipping weight
MATERIALS
L.F. UNIT
Basket
Cone
Surround
Voice coil
Magnet
H.F. UNIT
Diaphragm
Voice coil
Voice coil former
Cast aluminium
Polypropylene
Rubber
Aluminium
Ferrite
Aluminium
Edgewound alum. ribbon
Kapton
THIELE-SMALL PARAMETERS**
Resonant Frequency, fs
D.C. Voice Coil Resistance, Re
Mechanical Quality Factor, Qms
Electrical Quality Factor, Qes
Total Quality Factor, Qts
Equivalent Air Volume to Cms, Vas
Mechanical Compliance, Cms
Mechanical Resistance, Rms
Efficiency, o (%)
Effective Surface Area, Sd(m2)
Maximum Displacement, Xmax
Displacement Volume, Vd
52 Hz
5.5 ohms.
6.1
0.77
0.68
23 l
400 µm/N
1.22 kg/s
0.53
0.022 m2
5 mm.
110 cm.3
NOTES
*The power capacity corresponds to the RMS maximum value that
can dissipate the loudspeaker when a sinus signal is applied for a
period of at least two hours.
Program power is defined as the transducer’s ability to handle normal
music program material.
** T-S parameters are measured after an exercise period using a
preconditioning power test, using a velocity-current laser transducer,
and will reflect the long term parameters, once the loudspeaker has
been working for a short period of time.
NOTAS
*La potencia admisible corresponde a la máxima potencia RMS que
puede disipar el altavoz durante al menos dos horas, cuando se le
aplica una señal senoidal determinada.
Por potencia programa se entiende la capacidad del altavoz en el
manejo de señales transitorias, como sería el proporcionado por el
contenido de un pasaje musical normal.
* *Los parámetros T-S han sido medidos después de un periodo de
fatiga y estabilización de las suspensiones, mediante transductor laser
de velocidad-corriente, y son el reflejo de los parámetros a largo plazo
del altavoz, una vez éste haya sido instalado y haya trabajado en un
corto espacio de tiempo.
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
L.F. UNIT
FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m.
H.F. UNIT
- 31 -
