PHOTOCOUPLER PS9587,PS9587L1,PS9587L2,PS9587L3 HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE 8-PIN DIP HIGH-SPEED PHOTOCOUPLER NEPOC FOR CREEPAGE DISTANCE OF 8 mm Series DESCRIPTION The PS9587, PS9587L1, PS9587L2 and PS9587L3 are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and a signal processing circuit on the output side on one chip. The PS9587L1 and PS9587L2 are designed specifically for long creepage-distance as well as high common mode transient immunity (CMR) and high speed digital output type. Consequently, they are suitable for high speed logic interface that needs long creepage-distance (8 mm) on mounting. The PS9587L1 is lead bending type for long creepage distance. The PS9587L2 is lead bending type for long creepage distance (Gull-wing) for surface mount. The PS9587L3 is lead bending type (Gull-wing) for surface mounting. FEATURES * Long creepage distance (8 mm MIN.: PS9587L1, PS9587L2) * High common mode transient immunity (CM H, CML = 15 kV/ s MIN.) * High isolation voltage (BV = 5 000 Vr.m.s.) * High-speed response (10 Mbps) * Pulse width distortion ( tPHL tPLH = 10 ns TYP.) * Open collector output * Ordering number of tape product: PS9587L2-E3: 1 000 pcs/reel : PS9587L3-E3: 1 000 pcs/reel * Pb-Free product * Safety standards * UL approved: No. E72422 <R> * CSA approved: No. CA 101391 (CA5A, CAN/CSA-C22.2 60065, 60950) * BSI approved: No. 8937, 8938 * SEMKO approved: No. 615433 * NEMKO approved: No. P06207243 * DEMKO approved: No. 314091 * FIMKO approved: No. FI 22827 <R> * DIN EN60747-5-2 (VDE0884 Part2) approved: No. 40019182 (Option) APPLICATIONS * FA Network * Measurement equipment * PDP Document No. PN10678EJ04V0DS (4th edition) Date Published September 2009 NS The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field. PS9587,PS9587L1,PS9587L2,PS9587L3 <R> PACKAGE DIMENSIONS (UNIT: mm) DIP Type Lead Bending Type (Gull-wing) For Surface Mount 2 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 Lead Bending Type For Long Creepage Distance Lead Bending Type For Long Creepage Distance (Gull-wing) For Surface Mount Data Sheet PN10678EJ04V0DS 3 PS9587,PS9587L1,PS9587L2,PS9587L3 PHOTOCOUPLER CONSTRUCTION Parameter PS9587, PS9587L3 PS9587L1, PS9587L2 Air Distance (MIN.) 7 mm 8 mm Outer Creepage Distance (MIN.) 7 mm 8 mm 0.4 mm 0.4 mm Isolation Distance (MIN.) FUNCTIONAL DIAGRAM <R> MARKING EXAMPLE 4 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 ORDERING INFORMATION Part Number Order Number Solder Plating Packing Style Safety Standard Application Part Approval Number*1 Specification PS9587 PS9587-AX Pb-Free Magazine case 50 pcs Standard products PS9587 PS9587L1 PS9587L1-AX (Ni/Pd/Au) (UL, CSA, BSI, PS9587L1 PS9587L2 PS9587L2-AX SEMKO, NEMKO, PS9587L2 PS9587L3 PS9587L3-AX DEMKO, FIMKO PS9587L3 PS9587L2-E3 PS9587L2-E3-AX approved) PS9587L2 PS9587L3-E3 PS9587L3-E3-AX PS9587-V PS9587-V-AX PS9587L1-V Embossed Tape 1 000 pcs/reel PS9587L3 Magazine case 50 pcs DIN EN60747-5-2 PS9587 PS9587L1-V-AX (VDE0884 Part2) PS9587L1 PS9587L2-V PS9587L2-V-AX Approved (Option) PS9587L2 PS9587L3-V PS9587L3-V-AX PS9587L2-V-E3 PS9587L2-V-E3-AX PS9587L3-V-E3 PS9587L3-V-E3-AX PS9587L3 Embossed Tape 1 000 pcs/reel PS9587L2 PS9587L3 *1 For the application of the Safety Standard, following part number should be used. Data Sheet PN10678EJ04V0DS 5 PS9587,PS9587L1,PS9587L2,PS9587L3 ABSOLUTE MAXIMUM RATINGS (T A = 25 C, unless otherwise specified) Parameter Symbol Ratings Unit Forward Current*1 IF 30 mA Reverse Voltage VR 5 V Supply Voltage VCC 7 V Output Voltage VO 7 V IO 25 mA PC 40 mW Isolation Voltage BV 5 000 Vr.m.s. Operating Ambient Temperature TA 40 to +85 C Storage Temperature Tstg 55 to +125 C Diode Detecto r Output Current *2 Power Dissipation *3 *1 Reduced to 0.3 mA/ C at TA = 25 C or more. *2 Applies to output pin V O (Collector pin). Reduced to 1.5 mW/ C at TA = 65 C or more. *3 AC voltage for 1 minute at TA = 25 C, RH = 60% between input and output. Pins 1-4 shorted together, 5-8 shorted together. RECOMMENDED OPERATING CONDITIONS (T A = 25 C) Parameter Symbol MIN. TYP. MAX. Unit High Level Input Current IFH 6.3 10 12.0 mA Low Level Input Voltage VFL 0 0.8 V Supply Voltage VCC 4.5 5.5 V TTL (RL = 1 k , loads) N Pull-up Resistance RL 6 5.0 5 330 4k Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 ELECTRICAL CHARACTERISTICS (T A = 40 to +85 C, unless otherwise specified) Parameter Diode Detector Symbol Forward Voltage VF IF = 10 mA, TA = 25 C Reverse Current IR VR = 3 V, TA = 25 C Terminal Capacitance Ct VF = 0 V, f = 1 MHz, T A = 25 C IOH VCC = VO = 5.5 V, VF = 0.8 V Low Level Output Voltage VOL High Level Supply Current Low Level Supply Current High Level Output Current *2 Coupled Conditions Threshold Input Current (H L) MIN. 1.65 Unit 1.8 V 10 A 30 150 pF 1 100 A VCC = 5.5 V, IF = 5 mA, IOL = 13 mA 0.2 0.6 V ICCH VCC = 5.5 V, IF = 0 mA, VO = Open 5 8 mA ICCL VCC = 5.5 V, IF = 10 mA, VO = Open 9 11 mA 3.3 mA IFHL 1.4 TYP.*1 MAX. TA = 25 C VCC = 5 V, VO = 0.8 V, RL = 350 1.5 5 11 Isolation Resistance RI-O VI-O = 1 kVDC, RH = 40 to 60%, TA = 25 C Isolation Capacitance CI-O V = 0 V, f = 1 MHz, T A = 25 C 0.9 5 pF Propagation Delay Time tPHL VCC = 5 V, 35 75 ns (H *3 L) Propagation Delay Time (L 10 TA = 25 C VTHHL = VTHLH = 1.5 V, tPLH H)*3 RL = 350 , 100 TA = 25 C 45 IF = 7.5 mA, CL = 15 pF 75 ns 100 Rise Time tr 20 ns Fall Time tf 10 ns tPHL-tPLH 10 Pulse Width Distortion 50 ns 60 ns (PWD) *3 Propagation Delay Skew tPSK Common Mode CM H Transient Immunity at High Level VCC = 5 V, TA = 25 C, IF = 0 mA, 15 kV/ s 15 kV/ s VO (MIN.) = 2 V, VCM = 1.5 kV, RL = 350 Output*4 Common Mode Transient Immunity at Low Level Output*4 CM L VCC = 5 V, TA = 25 C, IF = 7.5 mA, VO (MAX.) = 0.8 V, VCM = 1.5 kV, RL = 350 Data Sheet PN10678EJ04V0DS 7 PS9587,PS9587L1,PS9587L2,PS9587L3 *1 Typical values at TA = 25 C *2 Because VOL of 2 V or more may be output when LED current is input and when output power supply is on and off, confirm the characteristics (operation with the power supply on and off) during design, before using this device. *3 Test circuit for propagation delay time *4 Test circuit for common mode transient immunity USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of more than 0.1 F is used between V CC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. *1 3. Pins 1, 4 (which is an NC pin) can either be connected directly to the GND pin on the LED side or left open. <R> *1 Also, Pin 7 (which is an NC pin) can either be connected directly to the GND pin on the detector side or left open. Unconnected pins should not be used as a bypass for signals or for any other similar purpose because this may degrade the internal noise environment of the device. *1 NC: Non-Connection (No Connection) 4. Avoid storage at a high temperature and high humidity. 8 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 TYPICAL CHARACTERISTICS (T A = 25 C, unless otherwise specified) Remark The graphs indicate nominal characteristics. Data Sheet PN10678EJ04V0DS 9 PS9587,PS9587L1,PS9587L2,PS9587L3 Remark The graphs indicate nominal characteristics. 10 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 TAPING SPECIFICATIONS (UNIT: mm) Data Sheet PN10678EJ04V0DS 11 PS9587,PS9587L1,PS9587L2,PS9587L3 12 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) Data Sheet PN10678EJ04V0DS 13 PS9587,PS9587L1,PS9587L2,PS9587L3 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering * Peak reflow temperature 260 C or below (package surface temperature) * Time of peak reflow temperature 10 seconds or less * Time of temperature higher than 220 C 60 seconds or less * Time to preheat temperature from 120 to 180 C 120 30 s * Number of reflows Three * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (2) Wave soldering * Temperature 260 C or below (molten solder temperature) * Time 10 seconds or less * Preheating conditions 120 C or below (package surface temperature) * Number of times One (Allowed to be dipped in solder including plastic mold portion.) * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron * Peak Temperature (lead part temperature) 350 C or below * Time (each pins) 3 seconds or less * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100 C 14 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 (4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler's input and output or between VCCGND at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. Data Sheet PN10678EJ04V0DS 15 PS9587,PS9587L1,PS9587L2,PS9587L3 <R> SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Symbol Climatic test class (IEC 60068-1/DIN EN 60068-1) Speck Unit 40/85/21 Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) Upr = 1.5 UIORM, Pd 5 pC UIORM Upr 1 130 1 695 Vpeak Vpeak Test voltage (partial discharge test, procedure b for all devices) Upr = 1.875 UIORM, Pd 5 pC Upr 2 119 Vpeak Highest permissible overvoltage UTR 8 000 Vpeak Degree of pollution (DIN EN 60664-1 VDE0110 Part 1) Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303 Part 11)) 2 CTI Material group (DIN EN 60664-1 VDE0110 Part 1) 175 III a Storage temperature range Tstg -55 to +125 C Operating temperature range TA -40 to +85 C Ris MIN. Ris MIN. 1012 1011 Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Tsi 175 C Current (input current IF, Psi = 0) Isi 400 mA Power (output or total power dissipation) Psi 700 mW Ris MIN. 109 Isolation resistance, minimum value VIO = 500 V dc at T A = 25C VIO = 500 V dc at T A MAX. at least 100C Isolation resistance VIO = 500 V dc at T A = Tsi 16 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 Data Sheet PN10678EJ04V0DS 17 PS9587,PS9587L1,PS9587L2,PS9587L3 Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth.