LF147/LF347 Wide Bandwidth Quad JFET Input Operational Amplifiers General Description Features The LF147 is a low cost, high speed quad JFET input operational amplifier with an internally trimmed input offset voltage (BI-FET IITM technology). The device requires a low supply current and yet maintains a large gain bandwidth product and a fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The LF147 is pin compatible with the standard LM148. This feature allows designers to immediately upgrade the overall performance of existing LF148 and LM124 designs. The LF147 may be used in applications such as high speed integrators, fast D/A converters, sample-and-hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth. The device has low noise and offset voltage drift. n n n n n n n n Simplified Schematic Connection Diagram Quad Internally trimmed offset voltage: 5 mV max Low input bias current: 50 pA Low input noise current: Wide gain bandwidth: 4 MHz High slew rate: 13 V/s Low supply current: 7.2 mA High input impedance: 1012 Low total harmonic distortion AV = 10,: < 0.02% RL = 10k, VO = 20 Vp-p, BW = 20 Hz-20 kHz n Low 1/f noise corner: 50 Hz n Fast settling time to 0.01%: 2 s Dual-In-Line Package 14 DS005647-1 DS005647-13 Note 1: Available per SMD #8102306, JM38510/11906. Top View Order Number LF147J, LF347M, LF347BN, LF347N, LF147D/883 or LF147J/883 (Note 1) See NS Package Number D14E, J14A, M14A or N14A BI-FET IITM is a trademark of National Semiconductor Corporation. (c) 1999 National Semiconductor Corporation DS005647 www.national.com LF147/LF347 Wide Bandwidth Quad JFET Input Operational Amplifiers April 1998 Absolute Maximum Ratings (Note 2) LF147 Surface Mount Wide (WM) Operating Temperature Range Storage Temperature Range Lead Temperature (Soldering, 10 sec.) Soldering Information Dual-In-Line Package Soldering (10 seconds) Small Outline Package Vapor Phase (60 seconds) Infrared (15 seconds) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Differential Input Voltage Input Voltage Range (Note 3) Output Short Circuit Duration (Note 4) Power Dissipation (Notes 5, 11) Tj max jA Cavity DIP (D) Package Ceramic DIP (J) Package Plastic DIP (N) Package Surface Mount Narrow (M) LF147 22V 38V 19V LF347B/LF347 18V 30V 15V Continuous Continuous 900 mW 1000 mW 150C 150C Parameter Input Offset Voltage Conditions LF147 RS = 10 k, TA = 25C Typ 1 Over Temperature VOS/T Average TC of Input Offset -65CTA150C 260C 260C 260C 215C 220C (Note 7) Min VOS (Note 6) See AN-450 "Surface Mounting Methods and Their Effect on Product Reliability" for other methods of soldering surface mount devices. ESD Tolerance (Note 12) 900V 80C/W 70C/W 75C/W 100C/W DC Electrical Characteristics Symbol LF347B/LF347 85C/W (Note 6) LF347B Max Min 5 Typ 3 8 RS = 10 k 10 Tj = 25C, (Notes 7, 8) 25 LF347 Max Min 5 Typ 5 7 Units Max 10 13 10 10 mV mV V/C Voltage IOS Input Offset Current Over Temperature IB Input Bias Current 50 Over Temperature RIN Input Resistance Tj = 25C Large Signal Voltage Gain VS = 15V, TA = 25C 25 25 Tj = 25C, (Notes 7, 8) AVOL 100 25 4 200 50 50 200 50 8 1012 50 100 1012 100 50 100 25 100 pA 4 nA 200 pA 8 nA 1012 100 V/mV VO = 10V, RL = 2 k Over Temperature 25 25 15 V/mV VO Output Voltage Swing VS = 15V, RL = 10 k 12 13.5 12 13.5 12 13.5 VCM Input Common-Mode Voltage VS = 15V 11 +15 11 +15 11 +15 V -12 V Range -12 -12 V CMRR Common-Mode Rejection Ratio RS10 k 80 100 80 100 70 100 dB PSRR Supply Voltage Rejection Ratio (Note 9) 80 100 80 100 70 100 dB IS Supply Current www.national.com 7.2 2 11 7.2 11 7.2 11 mA AC Electrical Characteristics Symbol Parameter (Note 7) Conditions LF147 Min Amplifier to Amplifier Coupling TA = 25C, Typ LF347B Max Min -120 Typ LF347 Max Min -120 Typ -120 Units Max dB f = 1 Hz-20 kHz (Input Referred) SR Slew Rate VS = 15V, TA = 25C 8 13 8 13 8 13 V/s GBW Gain-Bandwidth Product VS = 15V, TA = 25C 2.2 4 2.2 4 2.2 4 MHz en Equivalent Input Noise Voltage TA = 25C, RS = 100, in Equivalent Input Noise Current Tj = 25C, f = 1000 Hz 20 20 20 0.01 0.01 0.01 f = 1000 Hz Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Note 3: Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage. Note 4: Any of the amplifier outputs can be shorted to ground indefinitely, however, more than one should not be simultaneously shorted as the maximum junction temperature will be exceeded. Note 5: For operating at elevated temperature, these devices must be derated based on a thermal resistance of jA. Note 6: The LF147 is available in the military temperature range -55CTA125C, while the LF347B and the LF347 are available in the commercial temperature range 0CTA70C. Junction temperature can rise to Tj max = 150C. Note 7: Unless otherwise specified the specifications apply over the full temperature range and for VS = 20V for the LF147 and for VS = 15V for the LF347B/LF347. VOS, IB, and IOS are measured at VCM = 0. Note 8: The input bias currents are junction leakage currents which approximately double for every 10C increase in the junction temperature, Tj. Due to limited production test time, the input bias currents measured are correlated to junction temperature. In normal operation the junction temperature rises above the ambient temperature as a result of internal power dissipation, PD. Tj = TA+jA PD where jA is the thermal resistance from junction to ambient. Use of a heat sink is recommended if input bias current is to be kept to a minimum. Note 9: Supply voltage rejection ratio is measured for both supply magnitudes increasing or decreasing simultaneously in accordance with common practice from VS = 5V to 15V for the LF347 and LF347B and from VS = 20V to 5V for the LF147. Note 10: Refer to RETS147X for LF147D and LF147J military specifications. Note 11: Max. Power Dissipation is defined by the package characteristics. Operating the part near the Max. Power Dissipation may cause the part to operate outside guaranteed limits. Note 12: Human body model, 1.5 k in series with 100 pF. 3 www.national.com Typical Performance Characteristics Input Bias Current Input Bias Current DS005647-14 Positive Common-Mode Input Voltage Limit Supply Current DS005647-16 DS005647-15 Negative Common-Mode Input Voltage Limit Positive Current Limit DS005647-19 DS005647-17 Negative Current Limit DS005647-18 Output Voltage Swing DS005647-20 www.national.com Output Voltage Swing DS005647-21 4 DS005647-22 Typical Performance Characteristics (Continued) Bode Plot Gain Bandwidth Slew Rate DS005647-23 Distortion vs Frequency DS005647-24 Undistorted Output Voltage Swing DS005647-25 Open Loop Frequency Response DS005647-26 DS005647-27 Common-Mode Rejection Ratio Power Supply Rejection Ratio DS005647-29 Equivalent Input Noise Voltage DS005647-30 5 DS005647-28 DS005647-31 www.national.com Typical Performance Characteristics (Continued) Output Impedance Open Loop Voltage Gain DS005647-33 DS005647-32 www.national.com Inverter Settling Time 6 DS005647-34 Pulse Response RL = 2 k, CL = 10 pF Small Signal Inverting Small Signal Non-Inverting DS005647-5 DS005647-4 Large Signal Inverting Large Signal Non-Inverting DS005647-6 DS005647-7 Current Limit (RL = 100) DS005647-8 Exceeding the negative common-mode limit on either input will force the output to a high state, potentially causing a reversal of phase to the output. Exceeding the negative common-mode limit on both inputs will force the amplifier output to a high state. In neither case does a latch occur since raising the input back within the common-mode range again puts the input stage and thus the amplifier in a normal operating mode. Application Hints The LF147 is an op amp with an internally trimmed input offset voltage and JFET input devices (BI-FET II). These JFETs have large reverse breakdown voltages from gate to source and drain eliminating the need for clamps across the inputs. Therefore, large differential input voltages can easily be accommodated without a large increase in input current. The maximum differential input voltage is independent of the supply voltages. However, neither of the input voltages should be allowed to exceed the negative supply as this will cause large currents to flow which can result in a destroyed unit. 7 www.national.com Application Hints or that the unit is not inadvertently installed backwards in a socket as an unlimited current surge through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a destroyed unit. As with most amplifiers, care should be taken with lead dress, component placement and supply decoupling in order to ensure stability. For example, resistors from the output to an input should be placed with the body close to the input to minimize "pick-up" and maximize the frequency of the feedback pole by minimizing the capacitance from the input to ground. A feedback pole is created when the feedback around any amplifier is resistive. The parallel resistance and capacitance from the input of the device (usually the inverting input) to AC ground set the frequency of the pole. In many instances the frequency of this pole is much greater than the expected 3 dB frequency of the closed loop gain and consequently there is negligible effect on stability margin. However, if the feedback pole is less than approximately 6 times the expected 3 dB frequency a lead capacitor should be placed from the output to the input of the op amp. The value of the added capacitor should be such that the RC time constant of this capacitor and the resistance it parallels is greater than or equal to the original feedback pole time constant. (Continued) Exceeding the positive common-mode limit on a single input will not change the phase of the output; however, if both inputs exceed the limit, the output of the amplifier will be forced to a high state. The amplifiers will operate with a common-mode input voltage equal to the positive supply; however, the gain bandwidth and slew rate may be decreased in this condition. When the negative common-mode voltage swings to within 3V of the negative supply, an increase in input offset voltage may occur. Each amplifier is individually biased by a zener reference which allows normal circuit operation on 4.5V power supplies. Supply voltages less than these may result in lower gain bandwidth and slew rate. The LF147 will drive a 2 k load resistance to 10V over the full temperature range. If the amplifier is forced to drive heavier load currents, however, an increase in input offset voltage may occur on the negative voltage swing and finally reach an active current limit on both positive and negative swings. Precautions should be taken to ensure that the power supply for the integrated circuit never becomes reversed in polarity Detailed Schematic DS005647-9 www.national.com 8 Typical Applications Digitally Selectable Precision Attenuator DS005647-10 All resistors 1% tolerance * * * * Accuracy of better than 0.4% with standard 1% value resistors No offset adjustment necessary Expandable to any number of stages Very high input impedance A1 A2 A3 VO Attenuation 0 0 0 0 0 0 1 -1 dB 0 1 0 -2 dB 0 1 1 -3 dB 1 0 0 -4 dB 1 0 1 -5 dB 1 1 0 -6 dB 1 1 1 -7 dB 9 www.national.com Typical Applications (Continued) Long Time Integrator with Reset, Hold and Starting Threshold Adjustment DS005647-11 * VOUT starts from zero and is equal to the integral of the input voltage with respect to the threshold voltage: * * * Output starts when VINVTH Switch S1 permits stopping and holding any output value Switch S2 resets system to zero www.national.com 10 Typical Applications (Continued) Universal State Variable Filter DS005647-12 For circuit shown: fo = 3 kHz, fNOTCH = 9.5 kHz Q = 3.4 Passband gain: Highpass -- 0.1 Bandpass -- 1 Lowpass -- 1 Notch -- 10 * foxQ200 kHz * 10V peak sinusoidal output swing without slew limiting to 200 kHz * See LM148 data sheet for design equations 11 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted Hermetic Dual-In-Line Package (D) Order Number LF147D/883 NS Package Number D14E Ceramic Dual-In-Line Package (J) Order Number LF147J or LF147J/883 NS Package Number J14A www.national.com 12 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) S.O. Package (M) Order Number LF347M NS Package Number M14A Molded Dual-In-Line Package (N) Order Number LF347BN or LF347N NS Package Number N14A 13 www.national.com LF147/LF347 Wide Bandwidth Quad JFET Input Operational Amplifiers Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.