Bulletin PD-2.319 rev. C 01/03 MBR1635/ MBR1645 MBRB1635/ MBRB1645 SCHOTTKY RECTIFIER 16 Amp Description/ Features Major Ratings and Characteristics The MBR16.. Schottky rectifier has been optimized for low reverse leakage at high temperature. The proprietary barrier technology allows for reliable operation up to 150 C junction temperature. Typical applications are in switching power supplies, converters, free-wheeling diodes, and reverse battery protection. Characteristics MBR16.. Units IF(AV) Rectangular 16 A VRRM 35/45 V IFSM @ tp = 5 s sine 1800 A High purity, high temperature epoxy encapsulation for enhanced mechanical strength and moisture resistance VF 0.57 V Low forward voltage drop High frequency operation - 65 to 150 C Guard ring for enhanced ruggedness and long term reliability waveform @ 16 Apk, TJ = 125C TJ 150 C TJ operation Case Styles MBR1635/ MBR1645 MBRB1635/ MBRB1645 Base Cathode Base Cathode 2 1 Cathode 3 Anode TO-220AC www.irf.com 1 3 Anode N/C D2PAK 1 MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03 Voltage Ratings Part number VR MBR1635 MBR1645 Max. DC Reverse Voltage (V) 35 VRWM Max. Working Peak Reverse Voltage (V) 45 Absolute Maximum Ratings Parameters MBR16.. Units IF(AV) Max. Average Forward Current IFSM 16 Non-Repetitive Peak Surge Current A 1800 A 150 EAS Non-Repetitive Avalanche Energy 24 mJ IAR Repetitive Avalanche Current 3.6 A Conditions @ TC = 125 C, (Rated VR) Following any rated load 5s Sine or 3s Rect. pulse condition and with rated VRRM applied Surge applied at rated load condition halfwave single phase 60Hz TJ = 25 C, IAS = 3.6 Amps, L = 3.7 mH Current decaying linearly to zero in 1 sec Frequency limited by TJ max. VA = 1.5 x VR typical Electrical Specifications Parameters VFM IRM MBR16.. Units Max. Forward Voltage Drop(1) Conditions 0.63 V @ 16A TJ = 25 C 0.57 V @ 16A TJ = 125 C Max. Instantaneus Reverse Current 0.2 mA TJ = 25 C (1) 40 mA TJ = 125 C Rated DC voltage CT Max. Junction Capacitance 1400 pF VR = 5VDC, (test signal range 100Khz to 1Mhz) 25C LS Typical Series Inductance 8.0 nH Measured from top of terminal to mounting plane 10000 V/ s dv/dt Max. Voltage Rate of Change (Rated VR) (1) Pulse Width < 300s, Duty Cycle <2% Thermal-Mechanical Specifications Parameters MBR16.. Units TJ Max. Junction Temperature Range -65 to 150 Tstg Max. Storage Temperature Range -65 to 175 Conditions C C RthJC Max. Thermal Resistance Junction to Case 1.50 C/W DC operation RthCS Typical Thermal Resistance, Case to Heatsink 0.50 C/W Mounting surface, smooth and greased wt Approximate Weight T Mounting Torque Case Style 2 2 (0.07) g (oz.) Min. 6 (5) Max. 12 (10) Kg-cm (Ibf-in) TO-220AC JEDEC www.irf.com MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03 1000 1000 T =175C J ReverseCurrent - I (mA) R 100 125C 1 100C 75C .1 50C .01 25C .001 .0001 0 10 T =125C J Fig. 2 - Typical Values of Reverse Current Vs. Reverse Voltage 10000 1 .2 .4 .6 .8 10 15 20 25 30 35 40 45 ReverseVoltage- VR(V) T = 25C J .1 0 5 T =175C J JunctionCapacitance- C (pF) T InstantaneousForwardCurrent - IF (A) 100 150C 10 1 1.2 1.4 T =25C J 1000 100 0 1.6 10 20 30 40 50 ReverseVoltage- V (V) R ForwardVoltageDrop- V (V) FM Fig. 1 - Maximum Forward Voltage Drop Characteristics Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage Thermal Impedance- ZthJC(C/W ) 10 1 .1 D=0.50 D=0.33 D=0.25 D=0.17 D=0.08 P DM t 1 t2 Notes: 1. Dutyfactor D= t1/ t2 .01 SinglePulse (Thermal Resistance) .001 .00001 .0001 .001 2. PeakT =P xZ +T J DM thJC C .01 .1 1 10 100 t , Rectangular PulseDuration(Seconds) 1 Fig. 4 - Maximum Thermal Impedance ZthJC Characteristics www.irf.com 3 MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03 15 18TQ RthJC (DC) =1.50C/W 175 AveragePower Loss - (Watts) AllowableCaseTemperature- (C) 180 170 165 DC 160 155 150 0 4 8 12 16 20 24 D=0.08 D=0.17 D=0.25 D=0.33 10 D=0.50 5 0 0 28 DC RMSLimit 4 8 12 16 20 AverageForwardCurrent - I AverageForwardCurrent - IF(AV) (A) Fig. 5 - Maximum Allowable Case Temperature Vs. Average Forward Current 24 F(AV) 28 (A) Fig. 6 - Forward Power Loss Characteristics (A) 10000 Non-Repetitive Surge Current - I FSM At Any Rated Load Condition And With Rated VRRM Applied Following Surge 1000 100 10 100 1000 10000 Square Wave Pulse Duration - t p (microsec) Fig. 7 - Maximum Non-Repetitive Surge Current L DUT IRFP460 Rg = 25 ohm CURRENT MONITOR HIGH-SPEED SWITCH FREE-WHEEL DIODE + Vd = 25 Volt 40HFL40S02 Fig. 8 - Unclamped Inductive Test Circuit 4 www.irf.com MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03 Outline Table 10.54 (0.41) 1.32 (0.05) MAX. 3.78 (0.15) 1.22 (0.05) DIA. 3.54 (0.14) 6.48 (0.25) 6.23 (0.24) 2.92 (0.11) 2.54 (0.10) TERM 2 15.24 (0.60) 14.84 (0.58) 1 2 3 14.09 (0.55) 3.96 (0.16) 13.47 (0.53) 3.55 (0.14) Base Cathode 0.10 (0.004) 2.04 (0.080) MAX. 1.40 (0.05) 2.89 (0.11) 1.15 (0.04) 2.64 (0.10) 0.94 (0.04) 0.69 (0.03) 1 Cathode 1 3 3 Anode 0.61 (0.02) MAX. 4.57 (0.18) 4.32 (0.17) 5.08 (0.20) REF. Conform to JEDEC outline TO-220AC Dimensions in millimeters and (inches) 4.69 (0.18) 4.20 (0.16) 10.16 (0.40) REF. 1.32 (0.05) 1.22 (0.05) 6.47 (0.25) 15.49 (0.61) 93 6.18 (0.24) 14.73 (0.58) 5.28 (0.21) 2.61 (0.10) 4.78 (0.19) 2.32 (0.09) 0.55 (0.02) 8.89 (0.35) 3X REF. 1.40 (0.055) 1.14 (0.045) 2X 0.46 (0.02) 0.93 (0.37) MINIMUM RECOMMENDED FOOTPRINT 0.69 (0.27) 11.43 (0.45) Base Cathode 2 1 3 4.57 (0.18) 4.32 (0.17) 8.89 (0.35) 17.78 (0.70) 2 0.61 (0.02) MAX. 5.08 (0.20) REF. 1 N/C 3.81 (0.15) 3 Anode 2.08 (0.08) 2X 2.54 (0.10) 2X Conform to JEDEC outline D2Pak (SMD-220) Dimensions in millimeters and (inches) www.irf.com 5 MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03 Tape & Reel Information TRR 1.60 (0.063) 1.50 (0.059) 4.10 (0.161) 3.90 (0.153) FEED DIR ECTION 1.60 (0.063) 1.50 (0.059) 1.85 (0.073) DIA. 0.368 (0.0145) 0.342 (0.0135) 11.60 (0.457) 1.65 (0.065) 11.40 (0.449) 15.42 (0.609) 15.22 (0.601) TRL 1.75 (0.069) 10.90 (0.429) 1.25 (0.049) 10.70 (0.421) 24.30 (0.957) 23.90 (0.941) DIA. 4.72 (0.186) 16.10 (0.634) 4.52 (0.178) 15.90 (0.626) FEED DIRECTION 13.50 (0.532) 26.40 (1.039) 12.80 (0.504) DIA. 24.40 (0.961) SMD-220 Tape & Reel When ordering, indicate the part number, part orientation, and the quantity. Quantities are in multiples 60 (2.362) 360 (14.173) of 800 pieces per reel for both TRL and TRR. D IA . MIN . DIA. MAX. Dimensions in millimeters and (inches) Ordering Information Table Device Code MBR B 16 45 1 2 3 4 1 - Essential Part Number 2 - Package Style: none= TO-220 B 6 3 - Current Rating 4 - Voltage Rating = D2 Pak 35 = 35V 45 = 45V www.irf.com MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03 Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 01/03 www.irf.com 7