AT24C04C-SSHM-T - MICROCHIP TECHNOLOGY

AT24C04C/AT24C08C

I²C-Compatible (Two-Wire) Serial EEPROM

4‑Kbit (512 x 8), 8‑Kbit (1,024 x 8)

Features

• Low-Voltage Operation:

– VCC = 1.7V to 5.5V

• Internally Organized as 512 x 8 (4K) or 1,024 x 8 (8K)

• Industrial Temperature Range: -40°C to +85°C

• I2C-Compatible (Two-Wire) Serial Interface:

– 100 kHz Standard mode, 1.7V to 5.5V

– 400 kHz Fast mode, 1.7V to 5.5V

– 1 MHz Fast Mode Plus (FM+), 2.5V to 5.5V

• Schmitt Triggers, Filtered Inputs for Noise Suppression

• Bidirectional Data Transfer Protocol

• Write-Protect Pin for Full Array Hardware Data Protection

• Ultra Low Active Current (3 mA maximum) and Standby Current (6 μA maximum)

• 16-byte Page Write Mode:

– Partial page writes allowed

• Random and Sequential Read Modes

• Self-Timed Write Cycle within 5 ms Maximum

• ESD Protection > 4,000V

• High Reliability:

– Endurance: 1,000,000 write cycles

– Data retention: 100 years

• Green Package Options (Lead-free/Halide-free/RoHS compliant)

• Die Sale Options: Wafer Form and Tape and Reel Available

Packages

• 8-Lead PDIP, 8-Lead SOIC, 5-Lead SOT23, 8-Lead TSSOP, 8-Pad UDFN and 8-Ball VFBGA

Table of Contents

Features.......................................................................................................................... 1

Packages.........................................................................................................................1

1. Package Types (not to scale).................................................................................... 4

2. Pin Descriptions.........................................................................................................5

2.1. Device Address Inputs (A1, A2)................................................................................................... 5

2.2. Ground......................................................................................................................................... 5

2.3. Serial Data (SDA).........................................................................................................................5

2.4. Serial Clock (SCL)........................................................................................................................6

2.5. Write-Protect (WP)....................................................................................................................... 6

2.6. Device Power Supply................................................................................................................... 6

3. Description.................................................................................................................7

3.1. System Configuration Using Two-Wire Serial EEPROMs ........................................................... 7

3.2. Block Diagram.............................................................................................................................. 8

4. Electrical Characteristics........................................................................................... 9

4.1. Absolute Maximum Ratings..........................................................................................................9

4.2. DC and AC Operating Range.......................................................................................................9

4.3. DC Characteristics....................................................................................................................... 9

4.4. AC Characteristics......................................................................................................................10

4.5. Electrical Specifications..............................................................................................................11

5. Device Operation and Communication....................................................................13

5.1. Clock and Data Transition Requirements...................................................................................13

5.2. Start and Stop Conditions.......................................................................................................... 13

5.3. Acknowledge and No-Acknowledge...........................................................................................14

5.4. Standby Mode............................................................................................................................ 14

5.5. Software Reset...........................................................................................................................15

6. Memory Organization.............................................................................................. 16

6.1. Device Addressing..................................................................................................................... 16

7. Write Operations......................................................................................................19

7.1. Byte Write...................................................................................................................................19

7.2. Page Write..................................................................................................................................19

7.3. Acknowledge Polling.................................................................................................................. 20

7.4. Write Cycle Timing..................................................................................................................... 21

7.5. Write Protection..........................................................................................................................21

8. Read Operations..................................................................................................... 22

8.1. Current Address Read................................................................................................................22

8.2. Random Read............................................................................................................................ 22

AT24C04C/AT24C08C

8.3. Sequential Read.........................................................................................................................23

9. Device Default Condition from Microchip................................................................ 25

10. Packaging Information.............................................................................................26

10.1. Package Marking Information.....................................................................................................26

11. Revision History.......................................................................................................41

The Microchip Web Site................................................................................................ 42

Customer Change Notification Service..........................................................................42

Customer Support......................................................................................................... 42

Product Identification System........................................................................................43

Microchip Devices Code Protection Feature................................................................. 44

Legal Notice...................................................................................................................44

Trademarks................................................................................................................... 44

Quality Management System Certified by DNV.............................................................45

Worldwide Sales and Service........................................................................................46

AT24C04C/AT24C08C

1. Package Types (not to scale)

GND

Vcc

SCL

SDA

8-pad UDFN

(Top View)

8-lead PDIP/SOIC/TSSOP

(Top View)

NC 1

A1(1)/NC

GND

Vcc

SCL

SDA

GND

Vcc

SCL

SDA

8-ball VFBGA

(Top View)

5-lead SOT23(2)

(Top View)

SCL 1

GND

SDA

Vcc

4 5

A1(1)/NC

Note:

1. This pin is device address input (A1) pin on the AT24C04C and is a NC or no connect on the

AT24C08C. Refer to Pin Descriptions for additional details.

2. Refer to Device Addressing for details about addressing the SOT23 version of the device.

AT24C04C/AT24C08C

Package Types (not to scale)

2. Pin Descriptions

The descriptions of the pins are listed in Table 2-1.

Table 2-1. Pin Function Table

Name 8-Lead

PDIP

8-Lead

SOIC

8-Lead

TSSOP

5-Lead

SOT23

8-Pad

UDFN(1)

8-Ball

VFBGA

Function

NC 1 1 1 －1 1 No Connect

A1(2,3)/NC 2 2 2 －2 2 Device Address Input/

No Connect

A2(2)3 3 3 －3 3 Device Address Input

GND 4 4 4 2 4 4 Ground

SDA 5 5 5 3 5 5 Serial Data

SCL 6 6 6 1 6 6 Serial Clock

WP(2)7 7 7 5 7 7 Write-Protect

VCC 8 8 8 4 8 8 Device Power Supply

Note:

1. The exposed pad on this package can be connected to GND or left floating.

2. If the A1, A2 or WP pins are not driven, they are internally pulled down to GND. In order to operate

in a wide variety of application environments, the pull-down mechanism is intentionally designed to

be somewhat strong. Once these pins are biased above the CMOS input buffer’s trip

point (~0.5 x VCC), the pull‑down mechanism disengages. Microchip recommends connecting these

pins to a known state whenever possible.

3. This pin is device address input (A1) pin on the AT24C04C and is a NC or no connect on the

AT24C08C.

2.1 Device Address Inputs (A1, A2)

The A1 and A2 pins are device address inputs that are hard-wired (directly to GND or to VCC) for

compatibility with other two-wire Serial EEPROM devices. When the pins are hard-wired on the

AT24C04C, as many as four devices may be addressed on a single bus system. When the A2 pin is

hard‑wired on the AT24C08C, as many as two devices may be addressed on a single bus system. A

device is selected when a corresponding hardware and software match is true. If the pins are left floating,

the A1 and A2 pins will be internally pulled down to GND. However, due to capacitive coupling that may

appear in customer applications, Microchip recommends always connecting the address pins to a known

state. When using a pull-up resistor, Microchip recommends using 10 kΩ or less.

2.2 Ground

The ground reference for the power supply. GND should be connected to the system ground.

2.3 Serial Data (SDA)

The SDA pin is an open-drain bidirectional input/output pin used to serially transfer data to and from the

device. The SDA pin must be pulled high using an external pull-up resistor (not to exceed 10 kΩ in value)

AT24C04C/AT24C08C

Pin Descriptions

and may be wire-ORed with any number of other open-drain or open-collector pins from other devices on

the same bus.

2.4 Serial Clock (SCL)

The SCL pin is used to provide a clock to the device and to control the flow of data to and from the

device. Command and input data present on the SDA pin is always latched in on the rising edge of SCL,

while output data on the SDA pin is clocked out on the falling edge of SCL. The SCL pin must either be

forced high when the serial bus is idle or pulled high using an external pull-up resistor.

2.5 Write-Protect (WP)

The write-protect input, when connected to GND, allows normal write operations. When the WP pin is

connected directly to VCC, all write operations to the protected memory are inhibited.

If the pin is left floating, the WP pin will be internally pulled down to GND. However, due to capacitive

coupling that may appear in customer applications, Microchip recommends always connecting the WP

pin to a known state. When using a pull‑up resistor, Microchip recommends using 10 kΩ or less.

Table 2-2. Write-Protect

WP Pin Status Part of the Array Protected

At VCC Full Array

At GND Normal Write Operations

2.6 Device Power Supply

The VCC pin is used to supply the source voltage to the device. Operations at invalid VCC voltages may

produce spurious results and should not be attempted.

AT24C04C/AT24C08C

Pin Descriptions

3. Description

The AT24C04C/AT24C08C provides 4,096/8,192 bits of Serial Electrically Erasable and Programmable

Read-Only Memory (EEPROM) organized as 512/1,024 words of 8 bits each. The device's cascading

feature allows up to four devices (AT24C04C) or two devices (AT24C08C) to share a common two-wire

bus. These devices are optimized for use in many industrial and commercial applications where

low‑power and low‑voltage operations are essential. The devices are available in space-saving 8-lead

SOIC, 8-lead TSSOP, 8-pad UDFN, 8-lead PDIP, 5-lead SOT23 and 8-ball VFBGA packages. All

packages operate from 1.7V to 5.5V.

3.1 System Configuration Using Two-Wire Serial EEPROMs

I2C Bus Master:

Microcontroller

Slave 0

AT24CXXX

VCC

SDA

SCL

GND

VCC

GND

SCL

SDA

RPUP(max) = tR(max)

0.8473 x CL

RPUP(min) = VCC - VOL(max)

IOL

Slave 1

AT24CXXX

VCC

SDA

SCL

GND

Slave 3

AT24CXXX

VCC

SDA

SCL

GND

VCC

Note: Only two devices can be connected when using the AT24C08C.

AT24C04C/AT24C08C

Description

3.2 Block Diagram

1 page

Start

Stop

Detector

GND

Memory

System Control

Module

High Voltage

Generation Circuit

Data & ACK

Input/Output Control

Address Register

and Counter

Write

Protection

Control

DOUT

DIN

Hardware

Address

Comparator

Vcc

SCL

SDA

Power-on

Reset

Generator

EEPROM Array

Column Decoder

Row Decoder

Data Register

A1(1)

Note:

1. The A1 pin is not available on the AT24C08C.

AT24C04C/AT24C08C

Description

4. Electrical Characteristics

4.1 Absolute Maximum Ratings

Temperature under bias -55°C to +125°C

Storage temperature -65°C to +150°C

VCC 6.25V

Voltage on any pin with respect to ground -1.0V to +7.0V

DC output current 5.0 mA

ESD protection >4 kV

Note: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to

the device. This is a stress rating only and functional operation of the device at these or any other

conditions above those indicated in the operation listings of this specification is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

4.2 DC and AC Operating Range

Table 4-1. DC and AC Operating Range

AT24C04C/AT24C08C

Operating Temperature (Case) Industrial Temperature Range -40°C to +85°C

VCC Power Supply Low Voltage Grade 1.7V to 5.5V

4.3 DC Characteristics

Table 4-2. DC Characteristics

Parameter Symbol Minimum Typical(1)Maximum Units Test Conditions

Supply

Voltage

VCC 1.7 — 5.5 V

Supply

Current

ICC1 — 0.4 1.0 mA VCC = 5.0V, Read at

100 kHz

Supply

Current

ICC2 — 2.0 3.0 mA VCC = 5.0V, Write at

100 kHz

Standby

Current

ISB — — 1.0 μA VCC = 1.7V, VIN = VCC or

GND

— — 6.0 μA VCC = 5.5V, VIN = VCC or

GND

AT24C04C/AT24C08C

Electrical Characteristics

...........continued

Parameter Symbol Minimum Typical(1)Maximum Units Test Conditions

Input

Leakage

Current

ILI — 0.10 3.0 μA VIN = VCC or GND

Output

Leakage

Current

ILO — 0.05 3.0 μA VOUT = VCC or GND

Input Low

Level

VIL -0.6 — VCC x 0.3 V Note 2

Input High

Level

VIH VCC x 0.7 — VCC + 0.5 V Note 2

Output Low

Level

VOL1 — — 0.2 V VCC = 1.7V, IOL = 0.15 mA

Output Low

Level

VOL2 — — 0.4 V VCC = 3.0V, IOL = 2.1 mA

Note:

1. Typical values characterized at TA = +25°C unless otherwise noted.

2. This parameter is characterized but is not 100% tested in production.

4.4 AC Characteristics

Table 4-3. AC Characteristics(1)

Parameter Symbol Fast Mode Fast Mode Plus Units

VCC = 1.7V to 2.5V VCC = 2.5V to 5.5V

Min. Max. Min. Max.

Clock Frequency, SCL fSCL — 400 — 1000 kHz

Clock Pulse Width Low tLOW 1,200 — 500 — ns

Clock Pulse Width High tHIGH 600 — 400 — ns

Input Filter Spike

Suppression

tI— 100 — 50 ns

Clock Low to Data Out

Valid

tAA 100 900 50 450 ns

Bus Free Time between

Stop and Start

tBUF 1,200 — 500 — ns

Start Hold Time tHD.STA 600 — 250 — ns

Start Set-up Time tSU.STA 600 — 250 — ns

Data In Hold Time tHD.DAT 0 — 0 — ns

Data In Set-up Time tSU.DAT 100 — 100 — ns

Inputs Rise Time(2)tR— 300 — 300 ns

Inputs Fall Time(2)tF— 300 — 100 ns

AT24C04C/AT24C08C

Electrical Characteristics

...........continued

Parameter Symbol Fast Mode Fast Mode Plus Units

VCC = 1.7V to 2.5V VCC = 2.5V to 5.5V

Min. Max. Min. Max.

Stop Set-up Time tSU.STO 600 — 250 — ns

Data Out Hold Time tDH 50 — 50 — ns

Write Cycle Time tWR — 5 — 5 ms

Note:

1. AC measurement conditions:

– CL: 100 pF

– RPUP (SDA bus line pull-up resistor to VCC): 1.3 kΩ (1000 kHz), 4 kΩ (400 kHz),

10 kΩ (100 kHz)

– Input rise and fall times: ≤50 ns

– Input and output timing reference voltages: 0.5 x VCC

2. These parameters are determined through product characterization and are not 100% tested in

production.

Figure 4-1. Bus Timing

SCL

SDA In

SDA Out

tHIGH

tLOW

tDH

tAA tBUF

tSU.STO

tSU.DAT

tHD.DAT

tHD.STA

tSU.STA

4.5 Electrical Specifications

4.5.1 Power-Up Requirements and Reset Behavior

During a power-up sequence, the VCC supplied to the AT24C04C/AT24C08C should monotonically rise

from GND to the minimum VCC level, as specified in Table 4-1, with a slew rate no faster than 0.1 V/µs.

4.5.1.1 Device Reset

To prevent inadvertent write operations or any other spurious events from occurring during a power-up

sequence, the AT24C04C/AT24C08C includes a Power-on Reset (POR) circuit. Upon power-up, the

device will not respond to any commands until the VCC level crosses the internal voltage threshold (VPOR)

that brings the device out of Reset and into Standby mode.

The system designer must ensure the instructions are not sent to the device until the VCC supply has

reached a stable value greater than or equal to the minimum VCC level. Additionally, once the VCC is

AT24C04C/AT24C08C

Electrical Characteristics

greater than or equal to the minimum VCC level, the bus master must wait at least tPUP before sending the

first command to the device. See Table 4-4 for the values associated with these power-up parameters.

Table 4-4. Power-up Conditions(1)

Symbol Parameter Min. Max. Units

tPUP Time required after VCC is stable before the device can accept commands 100 －µs

VPOR Power-on Reset Threshold Voltage －1.5 V

tPOFF Minimum time at VCC = 0V between power cycles 500 －ms

Note:

1. These parameters are characterized but they are not 100% tested in production.

If an event occurs in the system where the VCC level supplied to the AT24C04C/AT24C08C drops below

the maximum VPOR level specified, it is recommended that a full power cycle sequence be performed by

first driving the VCC pin to GND, waiting at least the minimum tPOFF time and then performing a new

power-up sequence in compliance with the requirements defined in this section.

4.5.2 Pin Capacitance

Table 4-5. Pin Capacitance(1)

Symbol Test Condition Max. Units Conditions

CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V

CIN Input Capacitance (A1, A2 and SCL) 6 pF VIN = 0V

Note:

1. This parameter is characterized but is not 100% tested in production.

4.5.3 EEPROM Cell Performance Characteristics

Table 4-6. EEPROM Cell Performance Characteristics

Operation Test Condition Min. Max. Units

Write Endurance(1)TA = 25°C, VCC = 3.3V,

Page Write mode

1,000,000 — Write Cycles

Data Retention(1)TA = 55°C 100 — Years

Note:

1. Performance is determined through characterization and the qualification process.

AT24C04C/AT24C08C

Electrical Characteristics

5. Device Operation and Communication

The AT24C04C/AT24C08C operates as a slave device and utilizes a simple I2C-compatible two-wire

digital serial interface to communicate with a host controller, commonly referred to as the bus master. The

master initiates and controls all read and write operations to the slave devices on the serial bus, and both

the master and the slave devices can transmit and receive data on the bus.

The serial interface is comprised of just two signal lines: Serial Clock (SCL) and Serial Data (SDA).

The SCL pin is used to receive the clock signal from the master, while the bidirectional SDA pin is used to

receive command and data information from the master as well as to send data back to the master.

Data is always latched into the AT24C04C/AT24C08C on the rising edge of SCL and always output from

the device on the falling edge of SCL. Both the SCL and SDA pin incorporate integrated spike

suppression filters and Schmitt Triggers to minimize the effects of input spikes and bus noise.

All command and data information is transferred with the Most Significant bit (MSb) first. During bus

communication, one data bit is transmitted every clock cycle, and after eight bits (one byte) of data have

been transferred, the receiving device must respond with either an Acknowledge (ACK) or a

No-Acknowledge (NACK) response bit during a ninth clock cycle (ACK/NACK clock cycle) generated by

the master. Therefore, nine clock cycles are required for every one byte of data transferred. There are no

unused clock cycles during any read or write operation, so there must not be any interruptions or breaks

in the data stream during each data byte transfer and ACK or NACK clock cycle.

During data transfers, data on the SDA pin must only change while SCL is low, and the data must remain

stable while SCL is high. If data on the SDA pin changes while SCL is high, then either a Start or a Stop

condition will occur. Start and Stop conditions are used to initiate and end all serial bus communication

between the master and the slave devices. The number of data bytes transferred between a Start and a

Stop condition is not limited and is determined by the master. In order for the serial bus to be idle, both

the SCL and SDA pins must be in the logic-high state at the same time.

5.1 Clock and Data Transition Requirements

The SDA pin is an open-drain terminal and therefore must be pulled high with an external pull‑up resistor.

SCL is an input pin that can either be driven high or pulled high using an external pull‑up resistor. Data on

the SDA pin may change only during SCL low time periods. Data changes during SCL high periods will

indicate a Start or Stop condition as defined below. The relationship of the AC timing parameters with

respect to SCL and SDA for the AT24C04C/AT24C08C are shown in the timing waveform in Figure 4-1.

The AC timing characteristics and specifications are outlined in AC Characteristics.

5.2 Start and Stop Conditions

5.2.1 Start Condition

A Start condition occurs when there is a high-to-low transition on the SDA pin while the SCL pin is at a

stable logic ‘1’ state and will bring the device out of Standby mode. The master uses a Start condition to

initiate any data transfer sequence; therefore, every command must begin with a Start condition.

The device will continuously monitor the SDA and SCL pins for a Start condition but will not respond

unless one is detected. Refer to Figure 5-1 for more details.

5.2.2 Stop Condition

A Stop condition occurs when there is a low-to-high transition on the SDA pin while the SCL pin is stable

in the logic ‘1’ state.

AT24C04C/AT24C08C

Device Operation and Communication

The master can use the Stop condition to end a data transfer sequence with the AT24C04C/AT24C08C,

which will subsequently return to Standby mode. The master can also utilize a repeated Start condition

instead of a Stop condition to end the current data transfer if the master will perform another operation.

Refer to Figure 5-1 for more details.

5.3 Acknowledge and No-Acknowledge

After every byte of data is received, the receiving device must confirm to the transmitting device that it

has successfully received the data byte by responding with what is known as an Acknowledge (ACK).

An ACK is accomplished by the transmitting device first releasing the SDA line at the falling edge of the

eighth clock cycle followed by the receiving device responding with a logic ‘0’ during the entire high period

of the ninth clock cycle.

When the AT24C04C/AT24C08C is transmitting data to the master, the master can indicate that it is done

receiving data and wants to end the operation by sending a logic ‘1’ response to the AT24C04C/

AT24C08C instead of an ACK response during the ninth clock cycle. This is known as a No-Acknowledge

(NACK) and is accomplished by the master sending a logic ‘1’ during the ninth clock cycle, at which point

the AT24C04C/AT24C08C will release the SDA line so the master can then generate a Stop condition.

The transmitting device, which can be the bus master or the Serial EEPROM, must release the SDA line

at the falling edge of the eighth clock cycle to allow the receiving device to drive the SDA line to a logic ‘0’

to ACK the previous 8-bit word. The receiving device must release the SDA line at the end of the ninth

clock cycle to allow the transmitter to continue sending new data. A timing diagram has been provided in

Figure 5-1 to better illustrate these requirements.

Figure 5-1. Start Condition, Data Transitions, Stop Condition and Acknowledge

SCL

SDA

Must Be

Stable

SDA

Change

Allowed

SDA

Change

Allowed

Acknowledge

Valid

Stop

Condition

Start

Condition

1 2 8 9

SDA

Must Be

Stable Acknowledge Window

The transmitting device (Master or Slave)

must release the SDA line at this point to allow

the receiving device (Master or Slave) to drive the

SDA line low to ACK the previous 8-bit word.

The receiver (Master or Slave)

must release the SDA line at

this point to allow the transmitter

to continue sending new data.

5.4 Standby Mode

The AT24C04C/AT24C08C features a low-power Standby mode that is enabled when any one of the

following occurs:

• A valid power-up sequence is performed (see Power-Up Requirements and Reset Behavior).

• A Stop condition is received by the device unless it initiates an internal write cycle (see Write

Operations).

• At the completion of an internal write cycle (see Write Operations).

AT24C04C/AT24C08C

Device Operation and Communication

5.5 Software Reset

After an interruption in protocol, power loss or system Reset, any two‑wire device can be protocol reset

by clocking SCL until SDA is released by the EEPROM and goes high. The number of clock cycles until

SDA is released by the EEPROM will vary. The software Reset sequence should not take more than nine

dummy clock cycles. Once the software Reset sequence is complete, new protocol can be sent to the

device by sending a Start condition followed by the protocol. Refer to Figure 5-2 for an illustration.

Figure 5-2. Software Reset

SCL 9

Device is

8321

SDA

Dummy Clock Cycles

SDA Released

Software Reset

by EEPROM

In the event that the device is still non-responsive or remains active on the SDA bus, a power cycle must

be used to reset the device (see Power-Up Requirements and Reset Behavior).

AT24C04C/AT24C08C

Device Operation and Communication

6. Memory Organization

The AT24C04C is internally organized as 32 pages of 16 bytes each. The AT24C08C is internally

organized as 64 pages of 16 bytes each.

6.1 Device Addressing

6.1.1 AT24C04C Device Addressing

Accessing the device requires an 8-bit device address byte following a Start condition to enable the

device for a read or write operation. Since multiple slave devices can reside on the serial bus, each slave

device must have its own unique address so the master can access each device independently.

The Most Significant four bits of the device address byte is referred to as the device type identifier. The

device type identifier ‘1010’ (Ah) is required in bits 7 through 4 of the device address byte (see

Table 6‑1).

Following the 4-bit device type identifier are the hardware slave address bits, A2 and A1. These bits can

be used to expand the address space by allowing up to four Serial EEPROM devices on the same bus.

The A2 and A1 values must correlate with the voltage level on the corresponding hardwired device

address input pins A1 and A2. The A1 and A2 pins use an internal proprietary circuit that automatically

biases the pin to a logic ‘0’ state if the pin is allowed to float. In order to operate in a wide variety of

application environments, the pull‑down mechanism is intentionally designed to be somewhat strong.

Once these pins are biased above the CMOS input buffer’s trip point (~0.5 x VCC), the pull-down

mechanism disengages. Microchip recommends connecting the A1 and A2 pins to a known state

whenever possible.

When using the SOT23 package, the A1 and A2 pins are not accessible and are left floating. The

previously mentioned automatic pull‑down circuit will set these pins to a logic ‘0’ state. As a result, to

properly communicate with the device in the SOT23 package, the A2 and A1 software bits must always

be set to logic ‘0’ for any operation.

Following the A2 and A1 hardware slave address bits is bit A8 (bit 1 of the device address byte), which is

the Most Significant bit of the memory array word address. Refer to Table 6-1 to review the bit position.

The eighth bit (bit 0) of the device address byte is the Read/Write Select bit. A read operation is initiated if

this bit is high and a write operation is initiated if this bit is low.

Upon the successful comparison of the device address byte, the AT24C04C will return an ACK. If a valid

comparison is not made, the device will NACK.

Table 6-1. AT24C04C Device Address Byte

Package Device Type Identifier Hardware Slave

Address Bits

Most Significant Bit

of the Word

Address

R/W Select

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

SOIC, TSSOP,

UDFN, PDIP,

VFBGA

1 0 1 0 A2 A1 A8 R/W

SOT23 1 0 1 0 0 0 A8 R/W

AT24C04C/AT24C08C

Memory Organization

For all operations except the current address read, a word address byte must be transmitted to the device

immediately following the device address byte. The word address byte consists of the remaining eight bits

of the 9-bit memory array word address, and is used to specify which byte location in the EEPROM to

start reading or writing. Refer to Table 6-2 to review these bit positions.

Table 6-2. AT24C04C Word Address Byte

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

A7 A6 A5 A4 A3 A2 A1 A0

6.1.2 AT24C08C Device Addressing

Accessing the device requires an 8-bit device address byte following a Start condition to enable the

device for a read or write operation. Since multiple slave devices can reside on the serial bus, each slave

device must have its own unique address so the master can access each device independently.

The Most Significant four bits of the device address byte is referred to as the device type identifier. The

device type identifier ‘1010’ (Ah) is required in bits 7 through 4 of the device address byte (see

Table 6‑3).

Following the 4-bit device type identifier is the hardware slave address bit, A2. This bit can be used to

expand the address space by allowing up to two Serial EEPROM devices on the same bus. The A2 value

must correlate with the voltage level on the corresponding hardwired device address input pin A2. The A2

pin uses an internal proprietary circuit that automatically biases it to a logic ‘0’ state if the pin is allowed to

float. In order to operate in a wide variety of application environments, the pull‑down mechanism is

intentionally designed to be somewhat strong. Once the pin is biased above the CMOS input buffer’s trip

point (~0.5 x VCC), the pull-down mechanism disengages. Microchip recommends connecting the A2 pin

to a known state whenever possible.

When using the SOT23 package, the A2 pin is not accessible and is left floating. The previously

mentioned automatic pull‑down circuit will set this pin to a logic ‘0’ state. As a result, to properly

communicate with the device in the SOT23 package, the A2 software bit must always be set to logic ‘0’

for any operation.

Following the A2 hardware slave address bit are bits A9 and A8 (bit 2 and bit 1 of the device address

byte), which are the two Most Significant bits of the memory array word address. Refer to Table 6-3 to

review these bit positions.

The eighth bit (bit 0) of the device address byte is the Read/Write Select bit. A read operation is initiated if

this bit is high and a write operation is initiated if this bit is low.

Upon the successful comparison of the device address byte, the AT24C08C will return an ACK. If a valid

comparison is not made, the device will NACK.

Table 6-3. AT24C08C Device Address Byte

Package Device Type Identifier Hardware Slave

Address Bit

Most Significant Bits of the

Word Address

R/W Select

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

SOIC, TSSOP,

UDFN, PDIP,

VFBGA

1 0 1 0 A2 A9 A8 R/W

SOT23 1 0 1 0 0 A9 A8 R/W

AT24C04C/AT24C08C

Memory Organization

For all operations except the current address read, a word address byte must be transmitted to the device

immediately following the device address byte. The word address byte consists of the remaining eight bits

of the 10-bit memory array word address, and is used to specify which byte location in the EEPROM to

start reading or writing. Refer to Table 6-4 to review these bit positions.

Table 6-4. AT24C08C Word Address Byte

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

A7 A6 A5 A4 A3 A2 A1 A0

AT24C04C/AT24C08C

Memory Organization

7. Write Operations

All write operations for the AT24C04C/AT24C08C begin with the master sending a Start condition,

followed by a device address byte with the R/W bit set to logic ‘0’, and then by the word address byte.

The data value(s) to be written to the device immediately follow the word address byte.

7.1 Byte Write

The AT24C04C/AT24C08C supports the writing of a single 8-bit byte. Selecting a data word in the

AT24C04C requires a 9-bit word address and selecting a data word in the AT24C08C requires a 10-bit

word address.

Upon receipt of the proper device address and the word address bytes, the EEPROM will send an

Acknowledge. The device will then be ready to receive the 8-bit data word. Following receipt of the 8‑bit

data word, the EEPROM will respond with an ACK. The addressing device, such as a bus master, must

then terminate the write operation with a Stop condition. At that time, the EEPROM will enter an internally

self-timed write cycle, which will be completed within tWR, while the data word is being programmed into

the nonvolatile EEPROM. All inputs are disabled during this write cycle, and the EEPROM will not

respond until the write is complete.

Figure 7-1. Byte Write

SCL

SDA

Device Address Byte Word Address Byte Data Word

Start

Master

ACK

from

Slave

MSB MSB

Stop

Master

MSB

1 2 3 4 5 6 7 8 9

1 0 1 0 A2 @ A8 0 0

1 2 3 4 5 6 7 8 9

D7 D6 D5 D4 D3 D2 D1 D0 0

A7 A6 A5 A4 A3 A2 A1 A0 0

1 2 3 4 5 6 7 8 9

ACK

from

Slave

ACK

from

Slave

(1)

Note:

1. For the AT24C04C, the @ indicates the A1 hardware slave address bit. For the AT24C08C, the @

indicates the A9 word address bit.

7.2 Page Write

A page write operation allows up to 16 bytes to be written in the same write cycle, provided all bytes are

in the same row of the memory array (where address bits A8/A9 through A4 are the same). Partial page

writes of less than 16 bytes are also allowed.

A page write is initiated the same way as a byte write, but the bus master does not send a Stop condition

after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data

word, the bus master can transmit up to fifteen additional data words. The EEPROM will respond with an

ACK after each data word is received. Once all data to be written has been sent to the device, the bus

master must issue a Stop condition (see Figure 7-2) at which time the internally self-timed write cycle will

begin.

The lower four bits of the word address are internally incremented following the receipt of each data word.

The higher order address bits are not incremented and retain the memory page row location.

Page write operations are limited to writing bytes within a single physical page, regardless of the number

of bytes actually being written. When the incremented word address reaches the page boundary, the

address counter will rollover to the beginning of the same page. Nevertheless, creating a rollover event

should be avoided as previously loaded data in the page could become unintentionally altered.

AT24C04C/AT24C08C

Write Operations

Figure 7-2. Page Write

SCL

SDA

Start

Master

ACK

from

Slave

ACK

from

Slave

Device Address Byte Word Address Byte

MSB MSB

1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9

1 0 1 0 A2 @ A8 0 0

ACK

from

Slave

Stop

Master

ACK

from

Slave

Data Word (n) Data Word (n+x), max of 16 without rollover

1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9

MSB MSB

A7 A6 A5 A4 A3 A2 A1 A0 0

D7 D6 D5 D4 D3 D2 D1 D0 0 D7 D6 D5 D4 D3 D2 D1 D0 0

(1)

Note:

1. For the AT24C04C, the @ indicates the A1 hardware slave address bit. For the AT24C08C, the @

indicates the A9 word address bit.

7.3 Acknowledge Polling

An Acknowledge Polling routine can be implemented to optimize time-sensitive applications that would

prefer not to wait the fixed maximum write cycle time (tWR). This method allows the application to know

immediately when the Serial EEPROM write cycle has completed, so a subsequent operation can be

started.

Once the internally self-timed write cycle has started, an Acknowledge Polling routine can be initiated.

This involves repeatedly sending a Start condition followed by a valid device address byte with the R/W

bit set at logic ‘0’. The device will not respond with an ACK while the write cycle is ongoing. Once the

internal write cycle has completed, the EEPROM will respond with an ACK, allowing a new read or write

operation to be immediately initiated. A flowchart has been included below in Figure 7-3 to better illustrate

this technique.

Figure 7-3. Acknowledge Polling Flowchart

Did

the device

ACK?

Send any

Write

protocol.

Send

Stop

condition

to initiate the

Write cycle.

Send Start

condition followed

by a valid

Device Address

byte with R/W = 0.

Proceed to

next Read or

Write operation.

YES

AT24C04C/AT24C08C

Write Operations

7.4 Write Cycle Timing

The length of the self-timed write cycle (tWR) is defined as the amount of time from the Stop condition that

begins the internal write cycle to the Start condition of the first device address byte sent to the

AT24C04C/AT24C08C that it subsequently responds to with an ACK. Figure 7-4 has been included to

show this measurement. During the internally self-timed write cycle, any attempts to read from or write to

the memory array will not be processed.

Figure 7-4. Write Cycle Timing

tWR

Stop

Condition

Start

Condition

Data Word n

ACKD0

SDA

Stop

Condition

SCL 8 9

ACK

First Acknowledge from the device

to a valid device address sequence after

write cycle is initiated. The minimum tWR

can only be determined through

the use of an ACK Polling routine.

7.5 Write Protection

The AT24C04C/AT24C08C utilizes a hardware data protection scheme that allows the user to write-

protect the upper half (1K) memory array contents when the WP pin is at VCC (or a valid VIH). No write

protection will be set if the WP pin is at GND or left floating.

Table 7-1. AT24C04C/AT24C08C Write-Protect Behavior

WP Pin Voltage Part of the Array Protected

VCC Full Array

GND None － Write Protection Not Enabled

The status of the WP pin is sampled at the Stop condition for every byte write or page write operation

prior to the start of an internally self-timed write cycle. Changing the WP pin state after the Stop condition

has been sent will not alter or interrupt the execution of the write cycle.

If an attempt is made to write to the device while the WP pin has been asserted, the device will

acknowledge the device address, word address and data bytes, but no write cycle will occur when the

Stop condition is issued. The device will immediately be ready to accept a new read or write command.

AT24C04C/AT24C08C

Write Operations

8. Read Operations

Read operations are initiated the same way as write operations with the exception that the Read/Write

Select bit in the device address byte must be a logic ‘1’. There are three read operations:

• Current Address Read

• Random Address Read

• Sequential Read

8.1 Current Address Read

The internal data word address counter maintains the last address accessed during the last read or write

operation, incremented by one. This address stays valid between operations as long as the VCC is

maintained to the part. The address roll-over during a read is from the last byte of the last page to the first

byte of the first page of the memory.

A current address read operation will output data according to the location of the internal data word

address counter. This is initiated with a Start condition, followed by a valid device address byte with the

R/W bit set to logic ‘1’. The device will ACK this sequence and the current address data word is serially

clocked out on the SDA line. All types of read operations will be terminated if the bus master does not

respond with an ACK (it NACKs) during the ninth clock cycle. After the NACK response, the master may

send a Stop condition to complete the protocol, or it can send a Start condition to begin the next

sequence.

Figure 8-1. Current Address Read

SCL

SDA

Device Address Byte Data Word (n)

Start

Master

ACK

from

Slave

NACK

from

Master

Stop

Master

MSB MSB

1 0 1 0 A2 @ A8 1 0 D7 D6 D5 D4 D3 D2 D1 D0 1

1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9

(1)

Note:

1. For the AT24C04C, the @ indicates the A1 hardware slave address bit. For the AT24C08C, the @

indicates the A9 word address bit.

8.2 Random Read

A random read begins in the same way as a byte write operation does to load in a new data word

address. This is known as a “dummy write” sequence; however, the data byte and the Stop condition of

the byte write must be omitted to prevent the part from entering an internal write cycle. Once the device

address and word address are clocked in and acknowledged by the EEPROM, the bus master must

generate another Start condition. The bus master now initiates a current address read by sending a Start

condition, followed by a valid device address byte with the R/W bit set to logic ‘1’. In this second device

address byte, the bit position usually reserved for the Most Significant bit of the word address (bit 1 for

AT24C04C and bit 2 and 1 for AT24C08C) are "don’t care" bits since the address that will be read from is

determined only by what was sent in the dummy write portion of the sequence. The EEPROM will ACK

the device address and serially clock out the data word on the SDA line. All types of read operations will

be terminated if the bus master does not respond with an ACK (it NACKs) during the ninth clock cycle.

AT24C04C/AT24C08C

Read Operations

After the NACK response, the master may send a Stop condition to complete the protocol, or it can send

a Start condition to begin the next sequence.

Figure 8-2. Random Read

SCL

SDA

Start

Master

Device Address Byte Word Address Byte

MSB MSB

1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9

1 0 1 0 A2 @ A8 0 0

Dummy Write

Start

Master

Device Address Byte Data Word (n)

Stop

Master

MSB MSB

1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9

1 0 1 0 A2 @ X 1 0 D7 D6 D5 D4 D3 D2 D1 D0 1

A7 A6 A5 A4 A3 A2 A1 A0 0

ACK

from

Slave

ACK

from

Slave

ACK

from

Slave

NACK

from

Master

(1)

Note:

1. For the AT24C04C, the @ indicates the A1 hardware slave address bit. For the AT24C08C, the @

indicates a "don’t care" bit.

8.3 Sequential Read

Sequential reads are initiated by either a current address read or a random read. After the bus master

receives a data word, it responds with an Acknowledge. As long as the EEPROM receives an ACK, it will

continue to increment the word address and serially clock out sequential data words. When the maximum

memory address is reached, the data word address will roll-over and the sequential read will continue

from the beginning of the memory array. All types of read operations will be terminated if the bus master

does not respond with an ACK (it NACKs) during the ninth clock cycle. After the NACK response, the

master may send a Stop condition to complete the protocol, or it can send a Start condition to begin the

next sequence.

AT24C04C/AT24C08C

Read Operations

Figure 8-3. Sequential Read

SCL

SDA

Start

Master

ACK

from

Slave

ACK

from

Master

Device Address Byte Data Word (n)

MSB MSB

1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9

1 0 1 0 A2 @ A8 1 0 D7 D6 D5 D4 D3 D2 D1 D0 0

ACK

from

Master

NACK

from

Master

Stop

Master

ACK

from

Master

Data Word (n+1) Data Word (n+2) Data Word (n+x)

1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9

D7 D6 D5 D4 D3 D2 D1 D0 0 D7 D6 D5 D4 D3 D2 D1 D0 0 D7 D6 D5 D4 D3 D2 D1 D0 1

MSB MSB MSB

(1)

Note:

1. For the AT24C04C, the @ indicates the A1 hardware slave address bit. For the AT24C08C, the @

indicates the A9 word address bit.

AT24C04C/AT24C08C

Read Operations

9. Device Default Condition from Microchip

The AT24C04C/AT24C08C is delivered with the EEPROM array set to logic ‘1’, resulting in FFh data in all

locations.

AT24C04C/AT24C08C

Device Default Condition from Microchip

10. Packaging Information

10.1 Package Marking Information

AT24C04C and AT24C08C: Package Marking Information

Catalog Number Truncation

AT24C04C Truncation Code ###: 04C / ##: 4C

AT24C08C Truncation Code ###: 08C / ##: 8C

Date Codes Voltages

YY = Year Y = Year WW = Work Week of Assembly % = Minimum Voltage

16: 2016 20: 2020 6: 2016 0: 2020 02: Week 2 M: 1.7V min

17: 2017 21: 2021 7: 2017 1: 2021 04: Week 4

18: 2018 22: 2022 8: 2018 2: 2022 ...

19: 2019 23: 2023 9: 2019 3: 2023 52: Week 52

Country of Origin Device Grade Atmel Truncation

CO = Country of Origin H or U: Industrial Grade AT: Atmel

ATM: Atmel

ATML: Atmel

Trace Code

NNN = Alphanumeric Trace Code (2 Characters for Small Packages)

YYWWNNN

###% CO

ATMLHYWW

8-lead SOIC 8-lead TSSOP

YYWWNNN

###%CO

ATHYWW

8-pad UDFN

###

NNN

2.0 x 3.0 mm Body

Note 2: Package drawings are not to scale

Note 1: designates pin 1

5-lead SOT23

##%UYY

WWNNN

Note 3: For SOT23 package with date codes before 7B, the bottom line (YMXX) is marked on the bottom side and there is no Country of Assembly (

) mark on the top line.

8-lead PDIP

YYWWNNN

###% CO

ATMLUYWW

1.5 x 2.0 mm Body

8-ball VFBGA

###U

WNNN

AT24C04C/AT24C08C

Packaging Information

For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Note:

Microchip Technology Drawing No. C04-018D Sheet 1 of 2

8-Lead Plastic Dual In-Line (P) - 300 mil Body [PDIP]

8X b

8X b1

PLANE

.010 C

NOTE 1

TOP VIEW

END VIEWSIDE VIEW

AT24C04C/AT24C08C

Packaging Information

Microchip Technology Drawing No. C04-018D Sheet 2 of 2

For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Note:

8-Lead Plastic Dual In-Line (P) - 300 mil Body [PDIP]

Units INCHES

Dimension Limits MIN NOM MAX

Number of Pins N 8

Pitch e.100 BSC

Top to Seating Plane A - - .210

Molded Package Thickness A2 .115 .130 .195

Base to Seating Plane A1 .015

Shoulder to Shoulder Width E .290 .310 .325

Molded Package Width E1 .240 .250 .280

Overall Length D .348 .365 .400

Tip to Seating Plane L .115 .130 .150

Lead Thickness c.008 .010 .015

Upper Lead Width b1 .040 .060 .070

Lower Lead Width b.014 .018 .022

Overall Row Spacing eB - - .430

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

protrusions shall not exceed .010" per side.

Notes:

Dimensions D and E1 do not include mold flash or protrusions. Mold flash or

Pin 1 visual index feature may vary, but must be located within the hatched area.

§ Significant Characteristic

Dimensioning and tolerancing per ASME Y14.5M

DATUM A DATUM A

ALTERNATE LEAD DESIGN

(VENDOR DEPENDENT)

AT24C04C/AT24C08C

Packaging Information

0.25 CA–B D

SEATING

PLANE

TOP VIEW

SIDE VIEW

VIEW A–A

0.10 C

Microchip Technology Drawing No. C04-057-SN Rev D Sheet 1 of 2

For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Note:

8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC]

NOTE 5

NX b

0.10 CA–B

H0.23

(L1)

R0.13

VIEW C

SEE VIEW C

NOTE 1

AT24C04C/AT24C08C

Packaging Information

Microchip Technology Drawing No. C04-057-SN Rev D Sheet 2 of 2

8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC]

For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Note:

Foot Angle 0° - 8°

15°-5°

Mold Draft Angle Bottom

15°-5°

Mold Draft Angle Top

0.51-0.31

Lead Width

0.25-0.17

Lead Thickness

1.27-0.40LFoot Length

0.50-0.25hChamfer (Optional)

4.90 BSCDOverall Length

3.90 BSCE1Molded Package Width

6.00 BSCEOverall Width

0.25-0.10

Standoff

--1.25A2Molded Package Thickness

1.75--AOverall Height

1.27 BSC

Pitch

8NNumber of Pins

MAXNOMMINDimension Limits

MILLIMETERSUnits

protrusions shall not exceed 0.15mm per side.

3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or

REF: Reference Dimension, usually without tolerance, for information purposes only.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. § Significant Characteristic

4. Dimensioning and tolerancing per ASME Y14.5M

Notes:

Footprint L1 1.04 REF

5. Datums A & B to be determined at Datum H.

AT24C04C/AT24C08C

Packaging Information

RECOMMENDED LAND PATTERN

Microchip Technology Drawing C04-2057-SN Rev B

8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm Body [SOIC]

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

Notes:

Dimensioning and tolerancing per ASME Y14.5M1.

For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Note:

Dimension Limits

Units

CContact Pad Spacing

Contact Pitch

MILLIMETERS

1.27 BSC

MIN

MAX

5.40

Contact Pad Length (X8)

Contact Pad Width (X8)

1.55

0.60

NOM

SILK SCREEN

AT24C04C/AT24C08C

Packaging Information

/HDG3ODVWLF7KLQ6KULQN6PDOO2XWOLQH67±PP%RG\>76623@

1RWHV

 3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD

 'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH

 'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0

%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV

5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\

1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW

KWWSZZZPLFURFKLSFRPSDFNDJLQJ

8QLWV 0,//,0(7(56

'LPHQVLRQ/LPLWV 0,1 120 0$;

1XPEHURI3LQV 1 

3LWFK H %6&

2YHUDOO+HLJKW $ ± ± 

0ROGHG3DFNDJH7KLFNQHVV $   

6WDQGRII $  ± 

2YHUDOO:LGWK ( %6&

0ROGHG3DFNDJH:LGWK (   

0ROGHG3DFNDJH/HQJWK '   

)RRW/HQJWK /   

)RRWSULQW / 5()

)RRW$QJOH  ± 

/HDG7KLFNQHVV F  ± 

/HDG:LGWK E  ± 

NOTE 1

L1 L

0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%

AT24C04C/AT24C08C

Packaging Information

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

AT24C04C/AT24C08C

Packaging Information

0.15 C D

NOTE 1 1 2

TOP VIEW

SIDE VIEW

For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Note:

0.20 C

SEATING PLANE

AA2

NX bB

0.20 C A-B D

E1/2

E/2

0.20 C 2X

(DATUM D)

(DATUM A-B)

SEE SHEET 2

0.20 C

Microchip Technology Drawing C04-21344 Rev B Sheet 1 of 2

5-Lead Plastic Thin Small Outline Transistor (NMB) [TSOT]

Atmel Legacy Global Package Code TSZ

AT24C04C/AT24C08C

Packaging Information

For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Note:

(c)

VIEW A-A

SHEET 1

protrusions shall not exceed 0.25mm per side.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

Foot Angle

Number of Leads

Pitch

Outside lead pitch

Overall Height

Molded Package Thickness

Standoff

Overall Width

Molded Package Width

Overall Length

Foot Length

Footprint

Lead Thickness

Lead Width

Notes:

Dimension Limits

Units

0°

0.08

0.30 -

8°

0.20

0.50

MILLIMETERS

0.95 BSC

1.90 BSC

0.30

0.70

0.60 REF

2.90 BSC

2.80 BSC

1.60 BSC

0.90

MIN

NOM

1.10

1.00

0.10

0.60

MAX

REF: Reference Dimension, usually without tolerance, for information purposes only.

Dimensions D and E1 do not include mold flash or protrusions. Mold flash or

Dimensioning and tolerancing per ASME Y14.5M

Microchip Technology Drawing C04-21344 Rev B Sheet 2 of 2

5-Lead Plastic Thin Small Outline Transistor (NMB) [TSOT]

Atmel Legacy Global Package Code TSZ

AT24C04C/AT24C08C

Packaging Information

RECOMMENDED LAND PATTERN

Dimension Limits

Units

Contact Pitch

MILLIMETERS

0.95 BSC

MIN

MAX

Contact Pad Length (X5)

Contact Pad Width (X5)

1.05

0.60

NOM

SILK SCREEN

1 2

C 06.2gnicapS daP tcatnoC

Contact Pad to Center Pad (X2) G 0.20

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

Notes:

Dimensioning and tolerancing per ASME Y14.5M

For best soldering results, thermal vias, if used, should be filled or tented to avoid solder loss during

reflow process

For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Note:

Microchip Technology Drawing C04-23344 Rev B

5-Lead Plastic Thin Small Outline Transistor (NMB) [TSOT]

Atmel Legacy Global Package Code TSZ

AT24C04C/AT24C08C

Packaging Information

0.10 C

(DATUM B)

(DATUM A)

SEATING

PLANE

2X TOP VIEW

SIDE VIEW

NOTE 1

0.10 C A B

0.10 C

0.08 C

Microchip Technology Drawing C04-21355-Q4B Rev A Sheet 1 of 2

For the most current package drawings, please see the Microchip Packaging Specification locate d a t

http://www.microchip.com/packaging

Note:

8-Lead Ultra Thin Plastic Dual Flat, No Lead Packag e (Q4B) - 2x3 mm Body [UDFN]

Atmel Legacy YNZ Package

E2 K

L8X b

0.10 C A B

0.05 C

(A3)

BOTTOM VIEW

AT24C04C/AT24C08C

Packaging Information

REF: Reference Dimension, usually without tolerance, for information purposes only.

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

Notes:

Pin 1 visual index feature may vary, but must be located within the hatched area.

Package is saw singulated

Dimensioning and tolerancing per ASME Y14.5M

For the most current package drawings, please see the Microchip Packaging Specification locate d a t

http://www.microchip.com/packaging

Note:

Number of Terminals

Overall He ig ht

Terminal Width

Overall Width

Terminal Length

Exposed Pad Width

Terminal Thickness

Pitch

Standoff

Units

Dimension Limit s

N0.50 BSC

0.152 REF

1.20

0.35

0.18

0.50

0.00

0.25

0.40

1.30

0.55

0.02

3.00 BSC

MILLIMETERS

MIN NOM

1.40

0.45

0.30

0.60

0.05

MAX

K-0.20 -Terminal-to-Exposed-Pad

Overall Length

Exposed Pad Length D

D2 1.40 2.00 BSC

1.50 1.60

Microchip Technology Drawing C04-21355-Q4B Rev A Sheet 2 of 2

8-Lead Ultra Thin Plastic Dual Flat, No Lead Packag e (Q4B) - 2x3 mm Body [UDFN]

Atmel Legacy YNZ Package

AT24C04C/AT24C08C

Packaging Information

RECOMMENDED LAND PATTERN

Dimension Limit s

Units

Optional Center Pad Width

Optional Center Pad Length

Contact Pitch

X2 1.40

1.60

MILLIMETERS

0.50 BSC

MIN

EMAX

Contact Pad Length (X8)

Contact Pad Width (X8 ) Y1

X1 0.85

0.30

NOM

CContact Pad Spacing 2.90

Contact Pad to Center Pad (X8) G1 0.20

Thermal Via Diamete r V

Thermal Via Pitch EV 0.30

1.00

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

Notes:

Dimensioning and tolerancing per ASME Y14.5M

For best soldering results, thermal vias, if used, should be filled or ten t ed to avoid solder los s during

reflow process

For the most current package drawings, please see the Microchip Packaging Specification locate d a t

http://www.microchip.com/packaging

Note:

Microchip Technolo gy Drawing C04-21 35 5-Q4 B Re v A

8-Lead Ultra Thin Plastic Dual Flat, No Lead Packag e (Q4B) - 2x3 mm Body [UDFN]

Atmel Legacy YNZ Package

SILK SCREEN X1

ØV

Cont act Pad to Contact Pad (X6) G2 0.33

AT24C04C/AT24C08C

Packaging Information

DRAWING NO. REV. TITLE GPC

8U3-1 G

7/1/14

8U3-1, 8-ball, 1.50mm x 2.00mm body, 0.50mm pitch,

Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA) GXU

COMMON DIMENSIONS

(Unit of Measure - mm)

SYMBOL MIN NOM MAX NOTE

0.73 0.79 0.85

A1 0.09 0.14 0.19

A2 0.40 0.45 0.50

b 0.20 0.25 0.30 2

1.50 BSC

2.0 BSC

0.50 BSC

e1 0.25 REF

1.00 BSC

d1 0.25 REF

1. This drawing is for general information only.

2. Dimension ‘b’ is measured at maximum solder ball diameter.

3. Solder ball composition shall be 95.5Sn-4.0Ag-.5Cu.

Notes:

SIDE VIEW

PIN 1 BALL PAD CORNER

TOP VIEW

8 SOLDER BALLS

BOTTOM VIEW

(d1)

(e1)

PIN 1 BALL PAD CORNER

(4X)d0.10

d0.08 C

f0.10 C

j n 0.15 mC A B

j n 0.08mC

Note: For the most current package drawings, please see the Microchip Packaging Specification located

at http://www.microchip.com/packaging.

AT24C04C/AT24C08C

Packaging Information

11. Revision History

Revision A (December 2018)

Updated to the Microchip template. Microchip DS20006127 replaces Atmel document 8787. Updated Part

Marking Information. Corrected tLOW typo from 400 ns to 500 ns. Corrected tAA typo from 550 ns to

450 ns. Updated Part Marking Information. Updated the "Software Reset" section. Added ESD rating.

Removed lead finish designation. Updated trace code format in package markings. Added a figure for

“System Configuration Using Two‑Wire Serial EEPROMs”. Updated "Block Diagram" figure. Added POR

recommendations section. Updated section content throughout for clarification. Updated the 8U3‑1

VFBGA package drawing. Updated the PDIP, SOIC, TSSOP, SOT23 and UDFN package drawings to

Microchip format.

Atmel Document 8787 Revision F (December 2016)

Part marking SOT23:

• Moved backside mark (YMXX) to front side line2.

• Added @ = Country of Assembly

Atmel Document 8787 Revision E (January 2015)

Added the UDFN expanded quantity options and update the ordering information section. No change in

functional or electrical specification. Updated the 8P3, 8X, 8MA2, and 8U3-1 package outline drawings

and the disclaimer page.

Atmel Document 8787 Revision D (April 2013)

In the Page Write description, corrected from eight to 16 data words. Updated ordering code table,

footers, and disclaimer page.

Atmel Document 8787 Revision C (July 2012)

• Corrected ordering codes:

– AT24C04C-WWU11, Die Sale to AT24C04C-WWU11M, Wafer Sale.

– AT24C08C-WWU11, Die Sale to AT24C08C-WWU11M, Wafer Sale.

• Removed WDT from ordering code detail. Updated Atmel logos and disclaimer page.

Atmel Document 8787 Revision B (May 2012)

Removed preliminary status. Removed A0 signal from the block diagram. ISB2 parameter measured at

5.5V. In AC Characteristics table, changed 1.7V, 2.5V, 2.7V to 1.7 and 5.0V to 2.5V, 2.7V, 5.0V. Increased

tI maximum value from 50 ns to 100 ns. Enduranced parameter is studied at 3.3V, to +25°C, Page mode.

Removed Serial Number Read from read operations. Updated product markings. Updated 8X and 8U3-1

package drawings. Updated template.

Atmel Document 8787 Revision A (October 2011)

Initial release of this document.

AT24C04C/AT24C08C

Revision History

The Microchip Web Site

Microchip provides online support via our web site at http://www.microchip.com/. This web site is used as

a means to make files and information easily available to customers. Accessible by using your favorite

Internet browser, the web site contains the following information:

•Product Support – Data sheets and errata, application notes and sample programs, design

resources, user’s guides and hardware support documents, latest software releases and archived

software

•General Technical Support – Frequently Asked Questions (FAQ), technical support requests,

online discussion groups, Microchip consultant program member listing

•Business of Microchip – Product selector and ordering guides, latest Microchip press releases,

listing of seminars and events, listings of Microchip sales offices, distributors and factory

representatives

Customer Change Notification Service

Microchip’s customer notification service helps keep customers current on Microchip products.

Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata

related to a specified product family or development tool of interest.

To register, access the Microchip web site at http://www.microchip.com/. Under “Support”, click on

“Customer Change Notification” and follow the registration instructions.

Customer Support

Users of Microchip products can receive assistance through several channels:

• Distributor or Representative

• Local Sales Office

• Field Application Engineer (FAE)

• Technical Support

Customers should contact their distributor, representative or Field Application Engineer (FAE) for support.

Local sales offices are also available to help customers. A listing of sales offices and locations is included

in the back of this document.

Technical support is available through the web site at: http://www.microchip.com/support

AT24C04C/AT24C08C

Product Identification System

To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.

Product Family

24C = Standard I2C-compatible

Serial EEPROM

Device Density

Shipping Carrier Option

Device Grade or

Wafer/Die Thickness

Package Option

04 = 4 Kilobit

08 = 8 Kilobit

T = Tape and Reel, Standard Quantity Option

E = Tape and Reel, Extended Quantity Option

B or Blank = Bulk (Tubes)

Operating Voltage

M = 1.7V to 5.5V

H or U = Industrial Temperature Range

(-40°C to +85°C)

11 = 11mil Wafer Thickness

SS = SOIC

X = TSSOP

MA = 2.0mm x 3.0mm UDFN

P = PDIP

ST = SOT23

C = VFBGA

WWU = Wafer Unsawn

AT24C04C-SSHM-B

Device Revision

Examples

Device Package Package

Drawing

Code

Package

Option

Shipping Carrier Option Device Grade

AT24C04C‑PUM PDIP P P Bulk (Tubes) Industrial

Temperature

(-40°C to 85°C)

AT24C04C‑SSHM‑B SOIC SN SS Bulk (Tubes)

AT24C04C‑SSHM‑T SOIC SN SS Tape and Reel

AT24C08C‑SSHM‑T SOIC SN SS Tape and Reel

AT24C04C‑XHM‑B TSSOP ST X Bulk (Tubes)

AT24C08C‑XHM‑T TSSOP ST X Tape and Reel

AT24C04C‑MAHM‑T UDFN Q4B MA Tape and Reel

AT24C04C‑MAHM‑E UDFN Q4B MA Extended Qty. Tape and

Reel

AT24C08C‑MAHM‑E UDFN Q4B MA Extended Qty. Tape and

Reel

AT24C08C‑STUM‑T SOT23 NMB ST Tape and Reel

AT24C08C‑CUM‑T VFBGA 8U3-1 C Tape and Reel

AT24C04C/AT24C08C

Microchip Devices Code Protection Feature

Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the

market today, when used in the intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of

these methods, to our knowledge, require using the Microchip products in a manner outside the

operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is

engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their

code. Code protection does not mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the

code protection features of our products. Attempts to break Microchip’s code protection feature may be a

violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software

or other copyrighted work, you may have a right to sue for relief under that Act.

Legal Notice

Information contained in this publication regarding device applications and the like is provided only for

your convenience and may be superseded by updates. It is your responsibility to ensure that your

application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR

WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY

OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS

CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE.

Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life

support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend,

indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting

from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual

property rights unless otherwise stated.

Trademarks

The Microchip name and logo, the Microchip logo, AnyRate, AVR, AVR logo, AVR Freaks, BitCloud,

chipKIT, chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq,

Kleer, LANCheck, LINK MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB,

OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip Designer, QTouch, SAM-BA, SpyNIC, SST,

SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered trademarks of Microchip Technology

Incorporated in the U.S.A. and other countries.

ClockWorks, The Embedded Control Solutions Company, EtherSynch, Hyper Speed Control, HyperLight

Load, IntelliMOS, mTouch, Precision Edge, and Quiet-Wire are registered trademarks of Microchip

Technology Incorporated in the U.S.A.

Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom,

CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM,

dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming,

ICSP, INICnet, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, memBrain, Mindi, MiWi,

AT24C04C/AT24C08C

motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient

Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE,

Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total

Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are

trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.

SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.

Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries.

GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of

Microchip Technology Inc., in other countries.

All other trademarks mentioned herein are property of their respective companies.

ISBN: 978-1-5224-3943-1

Quality Management System Certified by DNV

ISO/TS 16949

Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer

fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California

and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC®

DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and

analog products. In addition, Microchip’s quality system for the design and manufacture of development

systems is ISO 9001:2000 certified.

AT24C04C/AT24C08C

AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE

Corporate Office

2355 West Chandler Blvd.

Chandler, AZ 85224-6199

Tel: 480-792-7200

Fax: 480-792-7277

Technical Support:

http://www.microchip.com/

support

Web Address:

www.microchip.com

Atlanta

Duluth, GA

Tel: 678-957-9614

Fax: 678-957-1455

Austin, TX

Tel: 512-257-3370

Boston

Westborough, MA

Tel: 774-760-0087

Fax: 774-760-0088

Chicago

Itasca, IL

Tel: 630-285-0071

Fax: 630-285-0075

Dallas

Addison, TX

Tel: 972-818-7423

Fax: 972-818-2924

Detroit

Novi, MI

Tel: 248-848-4000

Houston, TX

Tel: 281-894-5983

Indianapolis

Noblesville, IN

Tel: 317-773-8323

Fax: 317-773-5453

Tel: 317-536-2380

Los Angeles

Mission Viejo, CA

Tel: 949-462-9523

Fax: 949-462-9608

Tel: 951-273-7800

Raleigh, NC

Tel: 919-844-7510

New York, NY

Tel: 631-435-6000

San Jose, CA

Tel: 408-735-9110

Tel: 408-436-4270

Canada - Toronto

Tel: 905-695-1980

Fax: 905-695-2078

Australia - Sydney

Tel: 61-2-9868-6733

China - Beijing

Tel: 86-10-8569-7000

China - Chengdu

Tel: 86-28-8665-5511

China - Chongqing

Tel: 86-23-8980-9588

China - Dongguan

Tel: 86-769-8702-9880

China - Guangzhou

Tel: 86-20-8755-8029

China - Hangzhou

Tel: 86-571-8792-8115

China - Hong Kong SAR

Tel: 852-2943-5100

China - Nanjing

Tel: 86-25-8473-2460

China - Qingdao

Tel: 86-532-8502-7355

China - Shanghai

Tel: 86-21-3326-8000

China - Shenyang

Tel: 86-24-2334-2829

China - Shenzhen

Tel: 86-755-8864-2200

China - Suzhou

Tel: 86-186-6233-1526

China - Wuhan

Tel: 86-27-5980-5300

China - Xian

Tel: 86-29-8833-7252

China - Xiamen

Tel: 86-592-2388138

China - Zhuhai

Tel: 86-756-3210040

India - Bangalore

Tel: 91-80-3090-4444

India - New Delhi

Tel: 91-11-4160-8631

India - Pune

Tel: 91-20-4121-0141

Japan - Osaka

Tel: 81-6-6152-7160

Japan - Tokyo

Tel: 81-3-6880- 3770

Korea - Daegu

Tel: 82-53-744-4301

Korea - Seoul

Tel: 82-2-554-7200

Malaysia - Kuala Lumpur

Tel: 60-3-7651-7906

Malaysia - Penang

Tel: 60-4-227-8870

Philippines - Manila

Tel: 63-2-634-9065

Singapore

Tel: 65-6334-8870

Taiwan - Hsin Chu

Tel: 886-3-577-8366

Taiwan - Kaohsiung

Tel: 886-7-213-7830

Taiwan - Taipei

Tel: 886-2-2508-8600

Thailand - Bangkok

Tel: 66-2-694-1351

Vietnam - Ho Chi Minh

Tel: 84-28-5448-2100

Austria - Wels

Tel: 43-7242-2244-39

Fax: 43-7242-2244-393

Denmark - Copenhagen

Tel: 45-4450-2828

Fax: 45-4485-2829

Finland - Espoo

Tel: 358-9-4520-820

France - Paris

Tel: 33-1-69-53-63-20

Fax: 33-1-69-30-90-79

Germany - Garching

Tel: 49-8931-9700

Germany - Haan

Tel: 49-2129-3766400

Germany - Heilbronn

Tel: 49-7131-67-3636

Germany - Karlsruhe

Tel: 49-721-625370

Germany - Munich

Tel: 49-89-627-144-0

Fax: 49-89-627-144-44

Germany - Rosenheim

Tel: 49-8031-354-560

Israel - Ra’anana

Tel: 972-9-744-7705

Italy - Milan

Tel: 39-0331-742611

Fax: 39-0331-466781

Italy - Padova

Tel: 39-049-7625286

Netherlands - Drunen

Tel: 31-416-690399

Fax: 31-416-690340

Norway - Trondheim

Tel: 47-72884388

Poland - Warsaw

Tel: 48-22-3325737

Romania - Bucharest

Tel: 40-21-407-87-50

Spain - Madrid

Tel: 34-91-708-08-90

Fax: 34-91-708-08-91

Sweden - Gothenberg

Tel: 46-31-704-60-40

Sweden - Stockholm

Tel: 46-8-5090-4654

UK - Wokingham

Tel: 44-118-921-5800

Fax: 44-118-921-5820

Worldwide Sales and Service