LMV7219 7 nsec, 2.7V to 5V Comparator with Rail-to-Rail Output General Description Features The LMV7219 is a low-power, high-speed comparator with internal hysteresis. The LMV7219 operating voltage ranges from 2.7V to 5V with push/pull rail-to-rail output. This device achieves a 7ns propagation delay while consuming only 1.1mA of supply current at 5V. The LMV7219 inputs have a common mode voltage range that extends 200mV below ground, allowing ground sensing. The internal hysteresis ensures clean output transitions even with slow-moving inputs signals. (VS = 5V, TA = 25C, Typical values unless specified) n Propagation delay 7ns n Low supply current 1.1mA n Input common mode voltage range extends 200mv below ground n Ideal for 2.7V and 5V single supply applications n Internal hysteresis ensures clean switching n Fast rise and fall time 1.3ns n Available in space-saving packages: 5-pin SC70-5 and SOT23-5 The LMV7219 is available in the SC70-5 and SOT23-5 packages, which are ideal for systems where small size and low power are critical. Applications n n n n n n n Portable and battery-powered systems Scanners Set top boxes High speed differential line receiver Window comparators Zero-crossing detectors High-speed sampling circuits Typical Application 10105401 (c) 2004 National Semiconductor Corporation DS101054 www.national.com LMV7219 7 nsec, 2.7V to 5V Comparator with Rail-to-Rail Output November 2004 LMV7219 Connection Diagram SC70-5/SOT23-5 10105402 Top View Ordering Information Package 5-pin SC70-5 5-pin SOT23-5 Part Number Marking Supplied as LMV7219M7 C15 1k Units Tape and Reel LMV7219M7X C15 3k Units Tape and Reel LMV7219M5 C14A 1k Units Tape and Reel LMV7219M5X C14A 3k Units Tape and Reel NSC Drawing MAA05A MF05A Simplified Schematic 10105403 www.national.com 2 Voltage at Input/Output pins If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Current at Input Pin (Note 9) ESD Tolerance (Note 2) 10mA Operating Ratings Machine Body 150V Human Model Body Supply voltages (V+ - V-) 2000V Output Short Circuit Duration (Note 3) Supply Voltage (V+ - V-) -40C to +85C Storage Temperature Range 5.5V -65C to +150C Package Thermal Resistance Soldering Information Infrared or Convection (20 sec) 2.7V to 5V Operating Temperature Range (Note 4) Supply Voltage Differential Input Voltage Wave Soldering (10 sec) (V+) + 0.4V (V-) - 0.4V 235C SC70-5 478C/W SOT23-5 265C/W 260C (lead temp) 2.7V Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, VCM = V+/2, V+ = 2.7V, V- = 0V, CL = 10 pF and RL > 1 M to V-. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Typ (Note 5) Limit (Note 6) Units 1 6 8 mV max VOS Input Offset Voltage IB Input Bias Current 450 950 2000 nA max IOS Input Offset Current 50 200 400 nA max CMRR Common Mode Rejection Ratio 0V < VCM < 1.50V 85 62 55 dB min PSRR Power Supply Rejection Ratio V+ = 2.7V to 5V 85 65 55 dB min VCM Input Common-Voltage Range CMRR > 50 dB VCC -1 VCC -1.2 VCC -1.3 V min -0.2 -0.1 0 V max IL = 4 mA, VID = 500 mV VCC -0.22 VCC -0.3 VCC -0.4 IL = 0.4 mA, VID = 500 mV VCC -0.02 VCC -0.05 VCC -0.15 IL = -4 mA, VID = -500 mV 130 200 300 IL = -0.4 mA, VID = -500 mV 15 50 150 Sourcing, VO = 0V (Note 3) 20 Sinking, VO = 2.7V (Note 3) 20 VO Output Swing High Output Swing Low ISC Output Short Circuit Current V min mV max mA IS Supply Current No Load 0.9 VHYST Input Hysteresis Voltage (Note 10) 7 VTRIP+ Input Referred Positive Trip Point (see Figure 1) 3 8 mV max VTRIP- Input Referred Negative Trip Point (see Figure 1) -4 -8 mV min 3 1.6 2.2 mA max mV www.national.com LMV7219 Absolute Maximum Ratings (Note 1) LMV7219 2.7V Electrical Characteristics (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25C, VCM = V+/2, V+ = 2.7V, V- = 0V, CL = 10 pF and RL > 1 M to V-. Boldface limits apply at the temperature extremes. Symbol tPD Parameter Propagation Delay Conditions Typ (Note 5) Limit (Note 6) Units Overdrive = 5 mV VCM = 0V (Note 7) 12 Overdrive = 15 mV VCM = 0V (Note 7) 11 Overdrive = 50 mV VCM = 0V (Note 7) 10 1 ns ns max 20 tSKEW Propagation Delay Skew (Note 8) tr Output Rise Time 10% to 90% 2.5 ns tf Output Fall Time 90% to 10% 2 ns 5V Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, VCM = V+/2, V+ = 5V, V- = 0V, CL = 10 pF and RL > 1 M to V-. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Typ (Note 5) Limit (Note 6) Units 1 6 8 mV max VOS Input Offset Voltage IB Input Bias Current 500 950 2000 nA max IOS Input Offset Current 50 200 400 nA max CMRR Common Mode Rejection Ratio 0V < VCM < 3.8V 85 65 55 dB min PSRR Power Supply Rejection Ratio V+ = 2.7V to 5V 85 65 55 dB min VCM Input Common-Mode Voltage Range CMRR > 50 dB VCC -1 VCC -1.2 VCC -1.3 V min -0.2 -0.1 0 V max IL = 4 mA, VID = 500 mV VCC -0.13 VCC -0.2 VCC -0.3 IL = 0.4 mA, VID = 500 mV VCC -0.02 VCC -0.05 VCC -0.15 IL = -4 mA, VID = -500 mV 80 180 280 IL = -0.4 mA, VID = -500 mV 10 50 150 Sourcing, VO = 0V (Note 3) 68 30 20 Sinking, VO = 5V (Note 3) 65 30 20 1.8 2.4 VO Output Swing High Output Swing Low ISC Output Short Circuit Current V min mV max mA min IS Supply Current No Load 1.1 VHYST Input Hysteresis Voltage (Note 10) 7.5 VTrip+ Input Referred Positive Trip Point (See figure 1) 3.5 8 mV max VTrip- Input Referred Negative Trip Point (See figure 1) -4 -8 mV min www.national.com 4 mA max mV (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25C, VCM = V+/2, V+ = 5V, V- = 0V, CL = 10 pF and RL > 1 M to V-. Boldface limits apply at the temperature extremes. Symbol tPD Parameter Propagation Delay Conditions Typ (Note 5) Limit (Note 6) Units ns max Overdrive = 5 mV VCM = 0V (Note 7) 9 Overdrive = 15mV VCM = 0V (Note 7) 8 20 Overdrive = 50 mV VCM = 0V (Note 7) 7 19 tSKEW Propagation Delay Skew (Note 8) tr Output Rise Time tf Output Fall Time 0.4 ns 10% to 90% 1.3 ns 90% to 10% 1.25 ns Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical characteristics. Note 2: Human body model, 1.5 k in series with 100 pF. Machine model, 200 in series with 100 pF. Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Output currents in excess of 30mA over long term may adversely affect reliability. Note 4: The maximum power dissipation is a function of TJ(MAX), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/JA. All numbers apply for packages soldered directly into a PC board. Note 5: Typical Values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: Propagation delay measurements made with 100 mV steps. Overdrive is measure relative to VTrip. Note 8: Propagation Delay Skew is defined as absolute value of the difference between tPDLH and tPDHL. Note 9: Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage ratings. Note 10: The LMV7219 comparator has internal hysteresis. The trip points are the input voltage needed to change the output state in each direction. The offset voltage is defined as the average of Vtrip+ and Vtrip-, while the hysteresis voltage is the difference of these two. 5 www.national.com LMV7219 5V Electrical Characteristics LMV7219 Typical Performance Characteristics Unless otherwise specified, VS = 5V, CL = 10 pF, TA = 25C VOS vs. Supply Voltage Supply Current vs. Supply Voltage 10105404 10105405 Input Offset and Trip Voltage vs. Supply Voltage Sourcing Current vs. Output Voltage 10105408 10105406 Sourcing Current vs. Output Voltage Sinking Current vs. Output Voltage 10105409 www.national.com 10105410 6 Propagation Delay vs. Temperature (VS = 2.7V, VOD = 15 mV) Sinking Current vs. Output Voltage 10105412 10105411 Propagation Delay vs. Capacitive Load (VS = 5V, VOD = 15 mV) Propagation Delay vs. Temperature (VS = 5V, VOD = 15 mV) 10105413 10105414 Propagation Delay vs. Input Overdrive Propagation Delay (tPD-) 10105416 10105415 7 www.national.com LMV7219 Typical Performance Characteristics Unless otherwise specified, VS = 5V, CL = 10 pF, TA = 25C (Continued) LMV7219 Typical Performance Characteristics Unless otherwise specified, VS = 5V, CL = 10 pF, TA = 25C (Continued) Propagation Delay (tPD+) 10105417 The LMV7219 has a push pull output. When the output switches, there is a direct path between VCC and ground, causing high output sinking or sourcing current during the transition. After the transition, the output current decreases and the supply current settles back to about 1.1mA at 5V, thus conserving power consumption. Most high-speed comparators oscillate when the voltage of one of the inputs is close to or equal to the voltage on the other input due to noise or undesirable feedback. The LMV7219 have 7mV of internal hysteresis to counter parasitic effects and noise. The hysteresis does not change significantly with the supply voltages and the common mode input voltages as reflected in the specification table. Application Section LMV7219 is a single supply comparator with internal hysteresis, 7ns of propagation delay and only 1.1mA of supply current. The LMV7219 has a typical input common mode voltage range of -0.2V below the ground to 1V below Vcc. The differential input stage is a pair of PNP transistors, therefore, the input bias current flows out of the device. If either of the input signals falls below the negative common mode limit, the parasitic PN junction formed by the substrate and the base of the PNP will turn on, resulting in an increase of input bias current. If one of the inputs goes above the positive common mode limit, the output will still maintain the correct logic level as long as the other input stays within the common mode range. However, the propagation delay will increase. When both inputs are outside the common mode voltage range, current saturation occurs in the input stage, and the output becomes unpredictable. The propagation delay does not increase significantly with large differential input voltages. However, large differential voltages greater than the supply voltage should be avoided to prevent damages to the input stage. The internal hysteresis creates two trip points, one for the rising input voltage and one for the falling input voltage. The difference between the trip points is the hysteresis. With internal hysteresis, when the comparator's input voltages are equal, the hysteresis effectively causes one comparatorinput voltage to move quickly past the other, thus taking the input out of the region where oscillation occurs. Standard comparators require hysteresis to be added with external resistors. The fixed internal hysteresis eliminates these resistors. 10105418 FIGURE 1. Input and Output Waveforms, Non-Inverting Input Varied www.national.com 8 If additional hysteresis is desired, this can be done with the addition of three resistors using positive feedback, as shown in Figure 2. The positive feedback method slows the comparator response time. Calculate the resistor values as follows: 1) Select R3. The current through R3 should be greater than the input bias current to minimize errors. The current through R3 (IF) at the trip point is (VREF - VOUT) /R3. Consider the two possible output states when solving for R3, and use the smaller of the two resulting resistor values. The two formulas are: (when VOUT = 0) R3 = VREF/IF (VOUT = VCC) R3 = VCC - VREF /IF 2) Choose a hysteresis band required (VHB). 3) Calculate R1, where R1 = R3 X(VHB/VCC) 4) Choose the trip point for VIN rising. This is the threshold voltage (VTHR) at which the comparator switches from low to high as VIN rises about the trip point. 2. Keep all leads short to reduce stray capacitance and lead inductance. It will also minimize unwanted parasitic feedback around the comparator. 3. The device should be soldered directly to the PC board instead of using a socket. 4. Use a PC board with a good, unbroken low inductance ground plane. Make sure ground paths are low-impedance, especially were heavier currents are flowing. 5. Input traces should be kept away from output traces. This can be achieved by running a topside ground plane between the output and inputs. 6. Run the ground trace under the device up to the bypass capacitor to shield the inputs from the outputs. 7. To prevent parasitic feedback when input signals are slow-moving, a small capacitor of 1000pF or less can be placed between the inputs. It can also help eliminate oscillations in the transition region. However, this capacitor can cause some degradation to tpd when the source impedance is low. 5) Calculate R2 as follows: Zero-Crossing Detector The inverting input is connected to ground and the noninverting input is connected to 100mVp-p signal. As the signal at the non-inverting input crosses 0V, the comparator's output Changes State. 6) Verify the trip voltage and hysteresis as follows: 10105422 FIGURE 3. Zero-Crossing Detector This method is recommended for additional hysteresis of up to a few hundred millivolts. Beyond that, the impedance of R3 is low enough to affect the bias string and adjustment of R1 may be also required. Threshold Detector Instead of tying the inverting input to 0V, the inverting input can be tied to a reference voltage. The non-inverting input is connected to the input. As the input passes the VREF threshold, the comparator's output changes state. 10105421 FIGURE 2. Additional Hysteresis Circuit Layout and Bypassing 10105423 The LMV7219 requires high-speed layout. Follow these layout guidelines: 1. Power supply bypassing is critical, and will improve stability and transient response. A decoupling capacitor such as FIGURE 4. Threshold Detector 9 www.national.com LMV7219 0.1F ceramic should be placed as close as possible to V+ pin. An additional 2.2F tantalum capacitor may be required for extra noise reduction. Additional Hysteresis LMV7219 Crystal Oscillator IR Receiver A simple crystal oscillator using the LMV7219 is shown below. Resistors R1 and R2 set the bias point at the comparator's non-inverting input. Resistors R3, R4 and C1 sets the inverting input node at an appropriate DC average level based on the output. The crystal's path provides resonant positive feedback and stable oscillation occurs. The output duty cycle for this circuit is roughly 50%, but it is affected by resistor tolerances and to a lesser extent by the comparator offset. The LMV7219 is an ideal candidate to be used as an infrared receiver. The infrared photo diode creates a current relative to the amount of infrared light present. The current creates a voltage across RD. When this voltage level cross the voltage applied by the voltage divider to the inverting input, the output transitions. 10105425 FIGURE 6. IR Receiver 10105424 FIGURE 5. Crystal Oscillator www.national.com 10 LMV7219 Physical Dimensions inches (millimeters) unless otherwise noted 5-Pin SC70-5 NS Package Number MAA05A 11 www.national.com LMV7219 7 nsec, 2.7V to 5V Comparator with Rail-to-Rail Output Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 5-Pin SOT23-5 NS Package Number MF05A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560