PS398/PS399 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers Features Description * Low On-Resistance (60-ohm typ.) Minimizes Distortion and Error Voltages * Low Glitching Reduces Step Errors and Improves Settling Times. Charge Injection: <5pC * Split-Supply Operation (+3V to +8V) * Improved Second Sources for MAX398/MAX399 * On-Resistance Matching Between Channels: <6Ohm * On-Resistance Flatness: <11-ohm * Low Off-Channel Leakage, INO(OFF) < 1nA @ +85oC, ICOM(ON), <2.5nA @ +85oC * TTL/CMOS Logic Compatible * Fast Switching Speed, tTRANS <250ns * Break-Before-Make action eliminates momentary crosstalk * Rail-to-Rail Analog Signal Range * Low Power Consumption, <300W * Packaging (Pb-free & Green available): - 16-pin SOIC (W) The PS398/PS399 are improved high precision analog multiplexers. The PS398, an 8-channel single-ended mux, selects one of eight inputs to a common output as determined by a 3-bit address A0-A2. An EN (enable) pin when low disables all switches, useful when stacking several devices. The PS399 is a 4-channel differential multiplexer. It selects one of four differential inputs to a common differential output as determined by a 2-bit address A0, A1. An EN pin may be driven low to disable all switches. These multiplexers operate with dual supplies from +3V to +8V. Single-supply operation is possible from +3V to +15V. With +5V power supplies, the PS398/PS399 guarantee <100-ohm on-resistance. On-Resistance matching between channels is within 6-ohm. On-Resistance flatness is less than 11-ohm over the specified signal range. Each switch conducts current equally well in either direction when on. In the off state each switch blocks voltages up to the powersupply rails. Both devices guarantee low leakage currents (<2.5nA at +85oC) and fast switching speeds (tTRANS <250ns). Break-before-make switching action protects against momentary crosstalk between channels. Applications * * * * * * Data Acquisition Systems Audio Switching and Routing Test Equipment PBX, PABX Telecommunication Systems Battery-Powered Systems Block Diagrams and Pin Configurations PS399 PS398 A0 1 EN 2 V- 16 16 A1 AO 1 15 A2 EN 2 3 14 GND V- 3 NO1 4 13 V+ NO1A 4 13 NO1B NO2 5 12 NO5 NO2A 5 12 NO2B NO3 6 11 NO6 NO3A 6 11 NO3B NO4 7 10 NO7 NO4A 7 10 NO4B COM 8 Decoders/Drivers 9 COMA 8 NO8 1 Decoders/Drivers A1 15 GND 14 V+ 9 COMB PS8185F 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Truth Tables PS398 PS399 A2 A1 A0 EN On Switch X X X 0 None 0 0 0 1 1 0 0 1 1 2 0 1 0 1 0 1 1 1 0 1 A1 A0 EN ON Switch X X 0 None 0 0 1 1 3 0 1 1 2 1 4 1 0 1 3 0 1 5 1 1 1 4 0 1 1 6 1 1 0 1 7 1 1 1 1 8 Logic "0", VAL 0.8V Logic "1", VAH 2.4V Absolute Maximum Ratings Thermal Information Voltages Referenced to V- Continuous Power Dissipation V+ ....................................................................... -0.3V to + 17V SOIC (derate 8.7mW/ C above +70C) ........................... 650mW GND .................................................................... -0.3V to + 17V Storage Temperature ........................................ -65C to +150C GND ........................................................... -0.3V to ( V+) + 0.3V Lead Temperature (soldering, 10s) .................................. +300C VIN, VCOM, VNO (Note 1) ................... (V-) -2V to (V+) + 2V or 30mA, whichever occurs first Current (any terminal ) ......................................................... 30mA Peak Current, COM, NO, NC (pulsed at 1ms, 10% duty cycle) ..................................... 100mA ESD per method 3015.7 .................................................. > 2000V Note 1: Signals on NO, COM, or logic inputs exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to 30mA. Caution: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. 2 PS8185F 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Electrical Specifications - Dual Supplies (V = 5V 10%, GND = 0V, VAH = VENH = 2.4V, VAL = VENL = 0.8V) Parame te r Symbol Conditions Te mp. (C) M in.(2) Full V- Typ.(1) M ax.(2) Units Analog Switch Analog Signal Range (3) VANALOG On Resistance RON On- Resistance Match Between Channels(4) RON On- Resistance Flatness(5) RFLAT(ON) NO Off Leakage Current(6) COM- Off Leakage Current(6) V+ = 4.5V, V- = - 4.5V, VCOM = 3.5V INO = 1mA, INO(OFF) ICOM(OFF) 25 VCOM or VNC = 3.5V, INO = 1mA, V+ = 5V, V- = - 5V INO V+ = 5V, V- = - 5V, = 1mA, VCOM = 3V, 0V V+ = 5.5V, V- = - 5.5V, VCOM = 4.5V, VNO = 4.5V V+ = 5.5V, V- = - 5.5V VCOM = 4.5V, VNO = - /+4.5V P S 398 P S 399 P S 398 COM On Leakage Current(7) ICOM(ON) V+ = 5.5V, V- = - 5.5V VCOM = 4.5V VNO = 4.5V P S 399 V+ 60 V 100 Full 125 25 6 Full 8 25 11 Full 14 25 - 0.1 0.1 Full - 1.0 1.0 25 - 0.2 50 Full - 2.5 100 25 - 0.1 50 Full - 1.5 100 25 - 0.4 0.4 Full -5 5 25 - 0.2 0.2 Full - 2.5 2.5 Ohm nA Logic Input Logic High Input Voltage VAH, VENH Logic Low Input Voltage VAL, VENL 2.4 V 0.8 Full Input Current with Input Voltage High IAH, IENH Input Current with Input Voltage Low IAL, IENL VA = VEN = 2.4V - 0.1 0.1 A VA = VEN = 0.8V 3 - 0.1 0.1 PS8185F 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Electrical Specifications - Dual Supplies (V = 5V 10%, GND = 0V, VAH = VENH = 2.4V, VAL = VENL = 0.8V) (continued) Parame te r Te mp(C) M in.(1) Typ.(2) M ax.(1) Symbol Conditions Transition Time tTRANS Figure 1 Break- Before- Make Time Delay tOPEN Figure 3 Enable Turn- OnTime tON(EN) Figure 2 Enable Turn- Off Time tOFF(EN) Figure 2 Q CL= 1nF, VS = 0V, RS = 0Ohm, 2.8 OIRR VEN = 0V, RL= 1kOhm, f = 100kHz - 101 XTALK RL = 1kOhm, f = 100kHz, Figure 6 - 92 CIN f =1MHz 2.5 CNO(OFF) f =1MHz, VEN = VNO = 0V Units Dynamic Charge Injection(3) Off Isolation(7) Crosstalk Logic Input Capacitance NO Off Capacitance COM Off Capacitance COM On Capacitance CCOM(OFF) CCOM(ON) 150 0 25 40 72 Full 55 Full f =1MHz, VCOM = 0V ns 250 25 f =1MHz, VEN = VCOM =0V 150 150 200 25 5 pC dB 3.6 P S 398 31 P S 399 14 P S 398 35 P S 399 20 pF Supply Power- Supply Range Positive Supply Current NegativeSupply Current Ground Current I+ I- VEN = VA = 0V or V+, V+ =5.5V, V- = - 5.5V IGND Full 3 8 -1 1 -1 1 -1 1 V A Notes: 1. Algebraic convention, where the most negative value is a minimum and the most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. 3. Guaranteed by design. 4. RON = RON max - RON min. 5. Flatness is defined as the difference between the maximum and minimum values of on-resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25C. 7. Off Isolation = 20log10 VCOM / VNO. See Figure 5. 4 PS8185F 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Electrical Characteristics - Single 5V Supply (V+ = + 5V 10%, V- = 0V, GND = 0V, VAH = VENH = +2.4, VAL = VENL = +0.8V) Parame te r Symbol Te mp(C) M in.(1) Conditions Typ.(2) M ax.(1) Units V+ V Switch Analog Signal Range(3) On Resistance VCOM, VNO RON Full INO = 1mA, VCOM = 3.5V, V+ = 4.5V RON Matching Between Channels(4) RON INO = 1mA, VCOM = 3.5V, V+ = 4.5V On - Resistance Flatness RFLAT INO = 1mA, VCOM = 1.5V, 2.5V, 3.5V, V+ = 5V INO(OFF) VNO = 4.5V, VCOM = 0V, V+ = 5.5V NO- Off Leakage Current(8) COM- Off Leakage Current(8) COM- On Leakage Current(8) ICOM(OFF) ICOM(ON) VCOM = 4.5V, VNO =0V, V+ = 5.5V VCOM = 4.5V, VNO =4.5V, V+ = 5.5V P S 398 P S 399 P S 398 P S 399 0 25 100 225 Full 280 25 11 Full 13 25 18 Full 22 25 - 0.1 0.1 Full - 1.0 1.0 25 - 0.2 50 Full - 2.5 100 25 - 0.2 50 Full - 1.5 100 25 - 0.4 0.4 Full -5 5 25 - 0.2 0.2 Full - 2.5 2.5 Ohm n Digital Logic Input Logic High Input Voltage VAH, VENH Logic Low Input Voltage VAH, VENL Input Current with Input Voltage High IAH, IENH Input Current with Input Voltage Low IAH, IENL 2.4 0.8 VA= VEN = 2.4V Full - 0.1 V 0.1 A VA= VEN = 0.8V - 0.1 0.1 3 15 - 1.0 1.0 - 1.0 1.0 - 1.0 1.0 Supply Power- Supply Range V+ Positive- Supply Current I+ Negative- Supply Current I- Ground Current IGND VEN = V+ or 0V, VA = 0V, V+ = 5.5V, V- = 0V 5 Full PS8185F V 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Electrical Characteristics - Single 5V (V+ = +5V 10%, V- = 0V, GND = 0V, VAH = VENH = +2.4, VAL = VENL= +0.8V (continued) Parame te r Symbol Conditions Te mp(C) M in.(1) Typ.(2) M ax.(1) 72 245 Units Dynamic Transition Time tTRANS Break- Before- Make Interval tOPEN Enable Turn- On Time tON(EN) Enable Turn- Off Time tOFF(EN) Charge Injection(3) Q VNO = 3V 10 25 36 110 Full 275 25 65 Full CL = 1nF, VS = 0V, RS = 0Ohm 200 ns 125 200 25 2.8 5 pC Electrical Characteristics - Single 3V Supply (V+ = +3V 10%, V- = 0V, GND = 0V, VAH = VENH = +2.4, VAL = VENL = +0.8V) Parame te r Symbol Te mp.(C) M in.(1) Conditions Typ.(2) M ax.(1) Units V+ V Switch Analog Signal Range(3) VANALOG Full RON INO = 1mA, VCOM = 1.5V, V+ = 3V Transition Time(3) tTRANS Figure 1, VIN = 2.4V VNO1 = 1.5V, VNO8 = 0V Enable Turn- OnTime(3) tON(EN) Figure 2, VINH = 2.4V VINL = 0V, VNO1 = 1.5V Enable Turn- Off Time(3) tOFF(EN) Q On- Resistance 0 25 160 Full 375 425 Ohm Dynamic Charge Injection (3) 200 575 200 500 Figure 2, VINH = 2.4V VINL = 0V, VNO1 = 1.5V 92 400 CL = 10nF, VS = 0V, RS = 0Ohm 2 5 25 ns pC Notes: 1. The algebraic convention, where the most negative value is a minimum and the most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. 3. Guaranteed by design 4. R = R max - R min 5. Flatness is defined as the difference between the maximum and minimum value of on-resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25C. 7. Worst-case isolation is on channel 4 because of its proximity to the COM pin. Off isolation = 20log VCOM/VNO, VCOM = output, VNO = input to off switch 8. Leakage testing at single supply is guaranteed by testing with dual supplies. 6 PS8185F 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Test Circuits/Timing Diagrams Figure 1. Transition Time Figure 2. Enable Switching Time 7 PS8185F 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Figure 3. Break-Before-Make Interval +5V RS VEN VS Channel Select NO EN A0 A1 A2 V+ Logic Input VEN PS398 GND COM V- VOUT CL=1000pF +3V 0FF 0FF V OUT VOUT -5V ON 0VX C VOUT IS THE MEASURED VOLTAGE DUE TO CHARGE TRANSFER WHEN THE CHANNEL TURNS OFF. VOUT x C L Figure 4. Charge Injection Figure 5. Off Isolation Figure 6. CrossTalk 8 PS8185F 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 +5V A2 Channel Select A1 V+ N01 PS398 1MHz Capacitance Analyzer N08 A0 GND EN V- COM f =1MHz -5V Figure 8. NO/COM Capacitance Applications Overvoltage Protection Where n = number of channels scanned: 8 for PS398, 4 for PS399. tTRANS is given on the specification table: 150 ns max. Proper power-supply sequencing is recommended for all CMOS devices. Do not exceed the absolute maximum ratings, because stresses beyond the listed ratings may cause permanent damage to the devices. Always sequence V+ on first, followed by V-, and then logic inputs. If power-supply sequencing is not possible, add two small signal diodes or two current limiting resistors in series with the supply pins for overvoltage protection (Figure 9). Adding diodes reduces the analog signal range, but low switch resistance and low leakage characteristics are unaffected. Settling time is the time needed for the output to stabilize within the desired accuracy band of +1 LSB (least significant bit). Other factors determining settling time are: signal source impedance, capacitive load at the output. Figure 10 illustrates the steady state model. To figure out what the settling time due to the multiplexer is, we can assume that RS = 0, and CL = 0. In real life, the effects of RS and CL should be taken into account when performing these calculations. Maximum Sampling Rate From the sampling theorem, the sampling frequency needed to properly recover the original signal should be more than twice its maximum component frequency. In real applications, sampling at three or four times the maximum signal frequency is customary. Positive Supply V+ The maximum sampling rate of a multiplexer is determined by its transition time (tTRANS), the number of channels being multiplexed, and the settling time (tSETTLING) of the sampled signal at the output. The maximum sampling rate is: NO fS = 1 _______________ COM (1) n (tTRANS + tSETTLING) Vg V- Figure 9. Overvoltage protection is accomplished using two external blocking diodes or two current limiting resistors. 9 PS8185F 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 RON V IN RS CCOM(ON) CL VS Figure 10. Equivalent model of one multiplexer channel The table below shows how many time constants (m) are In equation (1) above, n = 8, tTRANS = 150ns, tSETTLING = 9, needed to reach an accuracy of one LSB. = RON x CCOM(ON) Bits 8 12 15 Accuracy (%) 0.25 0.012 0.0017 = 100ohm x 54pF 1 fS = _______________________ , m 6 9 11 8 [150ns + 9(100ohm x 54pF)] or fS = 630kHz. Assuming a x4 oversampling rate, the maximum sampling speed for the PS398 would be 630/4 = 157kHz. Now, let's calculate what the maximum sampling rate for the PS398. Assume a 12-bit accuracy and room temperature operation. 10 PS8185F 09/28/04 PS398/PS399 Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Packaging Mechanical: 16-pin SOIC (W) 16 .149 .157 3.78 3.99 .0099 .0196 0.25 x 45 0.50 1 .0075 .0098 0-8 .386 .393 9.80 10.00 0.41 1.27 .053 .068 .0155 .0260 0.393 0.660 REF 1.35 1.75 .013 .020 0.330 0.508 .016 .050 .2284 .2440 5.80 6.20 SEATING PLANE .050 BSC 1.27 0.19 0.25 .0040 0.10 .0098 0.25 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Ordering Information Ordering Code PS398CSE PS398CSEE PS398ESE PS398ESEE PS399CSE PS399CSEE PS399ESE PS399ESEE Package Code W W W W W W W W Package Type 16-pin SOIC Pb-free & Green, 16-pin SOIC 16-pin SOIC Pb-free & Green, 16-pin SOIC 16-pin SOIC Pb-free & Green, 16-pin SOIC 16-pin SOIC Pb-free & Green, 16-pin SOIC Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ Pericom Semiconductor Corporation * 1-800-435-2336 * www.pericom.com 11 PS8185F 09/28/04