790D www.vishay.com Vishay Sprague Resin-Molded, Radial-Lead Solid Tantalum Capacitors FEATURES * Terminations: Tin/lead (SnPb), 100 % tin (Sn) * Four case sizes precisely molded with a flame retardant epoxy resin * Stand off on all case sizes * Available on tape for automatic insertion equipment (only A- and B-case, C- and D-case on request) * Low leakage current * Low impedance * Extended value ranges available * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 Note * Lead (Pb)-containing terminations are not RoHS-compliant. Exemptions may apply. PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 C to + 125 C (above 85 C, voltage derating is required) Capacitance Range: 0.1 F to 330 F Capacitance Tolerance: 10 %, 20 % Voltage Rating: 6.3 VDC to 50 VDC ORDERING INFORMATION 790D 157 X0 006 R 2 P E3 MODEL CAPACITANCE CAPACITANCE TOLERANCE DC VOLTAGE RATING CASE CODE STYLE NUMBER PACKAGING RoHS COMPLIANT 790D = Standard and extended range Expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros following. X0 = 20 % X9 = 10 % Expressed in volts. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an "R" (6R3 = 6.3 V) See Ratings and Case Codes table Insulated case (standard) See packing information B: Bulk G: Ammopack (H = 16.5 mm) H: Ammopack (H = 18.5 mm) I: Ammopack shouldered leads (A case) X: Reel pack (H = 16.5 mm) Y: Reel pack (H = 18.5 mm) Z: Reel pack shouldered leads (A case) E3 = 100 % tin termination (RoHS compliant) Blank = SnPb termination DIMENSIONS in inches [millimeters] H 0.3 mm MIN. T + O 12 mm min. D e CASE CODE A B C D Revision: 18-Jun-12 H MAX. 0.287 [7.3] 0.413 [10.5] 0.413 [10.5] 0.413 [10.5] D MAX. 0.185 [4.7] 0.287 [7.3] 0.484 [12.3] 0.484 [12.3] T MAX. 0.165 [4.2] 0.189 [4.8] 0.287 [7.3] 0.484 [12.3] E 0.15 [0.006] 0.100 [2.54] 0.200 [5.08] 0.400 [10.16] 0.400 [10.16] O 0.05 [0.002] (+ 10 %) 0.020 [0.5] 0.020 [0.5] 0.024 [0.6] 0.024 [0.6] Document Number: 42072 1 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 790D www.vishay.com Vishay Sprague RATINGS AND CASE CODES RATED VOLTAGE UR AT + 85 C 6.3 V 10 V 16 V 4.0 V 6.3 V 10 V CR (F) 20 V 25 V 35 V 40 V 50 V 23 V 25 V 32 V CATEGORY VOLTAGE UC AT + 125 C STD. EXT. STD. EXT. STD. 13 V EXT. STD. 16 V EXT. STD. EXT. STD. EXT. STD. 0.10 EXT. A STD. A 0.15 A A 0.22 A A 0.33 A 0.47 A 0.68 A 1.0 1.5 A 2.2 A 3.3 A 4.7 6.8 A A A 22 A 33 B B 100 B C B C C C C C B C B C C B C C D D D C D C 220 B C C C B A B B B B 68 B C B B B 47 330 B B B A A 15 A B A A A B A 10 150 EXT. D D D D STANDARD RATINGS/EXTENDED RATINGS CAPACITANCE CR (F) CASE CODE PART NUMBER MAX. DCL AT + 25 C (A) MAX. DF 120 Hz, AT + 25 C (%) MAX. IMPEDANCE 100 kHz, AT + 25 C () UR = 6.3 VDC AT + 85 C, SURGE = 8 V; UC = 4 VDC AT + 125 C, SURGE = 5 V 6.8 A 790D685X(1)6R3A2(2) 1.0 6 4.0 22 A 790D226X(1)6R3A2(2) 1.3 6 2.1 47 B 790D476X(1)6R3B2(2) 2.9 6 1.3 68 B 790D686X(1)6R3B2(2) 4.2 6 1.3 150 C 790D157X(1)6R3C2(2) 9.4 6 0.6 220 C 790D227X(1)6R3C2(2) 13.8 6 0.6 330 D 790D337X(1)6R3D2(2) 20.7 8 0.4 Notes * Part number definitions: (1) Insert 0 for 20 % tolerance or 9 for 10 % (2) See Ordering Information, packaging code * Extended ratings in bold print Revision: 18-Jun-12 Document Number: 42072 2 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 790D www.vishay.com Vishay Sprague STANDARD RATINGS/EXTENDED RATINGS CAPACITANCE CR (F) CASE CODE PART NUMBER MAX. DCL AT + 25 C (A) MAX. DF 120 Hz, AT + 25 C (%) MAX. IMPEDANCE 100 kHz, AT + 25 C () UR = 10 VDC AT + 85 C, SURGE = 13 V; UC = 6.3 VDC AT + 125 C, SURGE = 8 V 4.7 A 790D475X(1)010A2(2) 1.0 6 4.0 15 A 790D156X(1)010A2(2) 1.5 6 2.5 33 B 790D336X(1)010B2(2) 3.3 6 1.3 47 B 790D476X(1)010B2(2) 4.7 6 1.4 68 B 790D686X(1)010B2(2) 6.8 6 1.3 0.6 100 C 790D107X(1)010C2(2) 10.0 6 150 C 790D157X(1)010C2(2) 15.0 6 0.6 220 D 790D227X(1)010D2(2) 22.0 8 0.4 UR = 16 VDC AT + 85 C, SURGE = 20 V; UC = 10 VDC AT + 125 C, SURGE = 13 V 2.2 A 790D225X(1)016A2(2) 1.0 6 5.5 3.3 A 790D335X(1)016A2(2) 1.0 6 4.4 10 A 790D106X(1)016A2(2) 1.6 6 2.7 15 B 790D156X(1)016B2(2) 2.4 6 1.6 22 B 790D226X(1)016B2(2) 3.5 6 1.3 33 B 790D336X(1)016B2(2) 5.2 6 1.6 47 C 790D476X(1)016C2(2) 7.5 6 0.8 68 C 790D686X(1)016C2(2) 10.8 6 0.6 100 C 790D107X(1)016C2(2) 16.0 6 0.7 100 D 790D107X(1)016D2(2) 16.0 6 0.5 D 790D157X(1)016D2(2) 24.0 8 0.4 150 UR = 20 VDC AT + 85 C, SURGE = 26 V; UC = 13 VDC AT + 125 C, SURGE = 16 V 2.2 A 790D225X(1)020A2(2) 1.0 6 5.5 6.8 A 790D685X(1)020A2(2) 1.3 6 3.5 15 B 790D156X(1)020B2(2) 3.0 6 1.5 22 B 790D226X(1)020B2(2) 4.4 6 2.1 0.7 47 C 790D476X(1)020C2(2) 9.4 6 68 C 790D686X(1)020C2(2) 13.6 6 0.8 100 D 790D107X(1)020D2(2) 20.0 6 0.7 UR = 25 VDC AT + 85 C, SURGE = 32 V; UC = 16 VDC AT + 125 C, SURGE = 20 V 1.5 A 790D155X(1)025A2(2) 1.0 6 6.0 4.7 A 790D475X(1)025A2(2) 1.1 6 4.5 10 B 790D106X(1)025B2(2) 2.5 6 1.6 15 B 790D156X(1)025B2(2) 3.7 6 2.4 22 B 790D226X(1)025B2(2) 5.5 6 2.1 33 C 790D336X(1)025C2(2) 8.2 6 0.8 47 D 790D476X(1)025D2(2) 11.8 6 1.0 UR = 35 VDC AT + 85 C, SURGE = 45 V; UC= 23 VDC AT + 125 C, SURGE = 29 V 3.3 A 790D335X(1)035A2(2) 1.2 6 6.0 10 B 790D106X(1)035B2(2) 3.5 6 2.6 33 C 790D336X(1)035C2(2) 11.6 6 1.3 Notes * Part number definitions: (1) Insert 0 for 20 % tolerance or 9 for 10 % (2) See Ordering Information, packaging code * Extended ratings in bold print Revision: 18-Jun-12 Document Number: 42072 3 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 790D www.vishay.com Vishay Sprague STANDARD RATINGS/EXTENDED RATINGS CAPACITANCE CR (F) CASE CODE PART NUMBER MAX. DCL AT + 25 C (A) MAX. DF 120 Hz, AT + 25 C (%) MAX. IMPEDANCE 100 kHz, AT + 25 C () UR = 40 VDC AT + 85 C, SURGE = 52 V; UC = 25 VDC AT + 125 C, SURGE = 32 V 0.10 A 790D104X(1)040A2(2) 1.0 6 30.0 0.15 A 790D154X(1)040A2(2) 1.0 6 24.0 0.22 A 790D224X(1)040A2(2) 1.0 6 18.0 0.33 A 790D334X(1)040A2(2) 1.0 6 14.0 0.47 A 790D474X(1)040A2(2) 1.0 6 11.0 1.0 A 790D105X(1)040A2(2) 1.0 6 6.5 1.5 B 790D155X(1)040B2(2) 1.0 6 5.2 2.2 B 790D225X(1)040B2(2) 1.0 6 4.0 3.3 A 790D335X(1)040A2(2) 1.3 6 2.8 3.3 B 790D335X(1)040B2(2) 1.3 6 2.8 4.7 B 790D475X(1)040B2(2) 1.8 6 2.0 6.8 B 790D685X(1)040B2(2) 2.7 6 1.6 10 C 790D106X(1)040C2(2) 4.0 6 1.3 15 C 790D156X(1)040C2(2) 6.0 6 1.0 22 C 790D226X(1)040C2(2) 8.8 6 0.8 33 D 790D336X(1)040D2(2) 13.2 6 0.6 D 790D476X(1)040D2(2) 18.8 6 0.5 47 UR = 50 VDC AT + 85 C, SURGE = 65 V; UC = 32 VDC AT + 125 C, SURGE = 41 V 0.10 A 790D104X(1)050A2(2) 1.0 6 30 0.15 A 790D154X(1)050A2(2) 1.0 6 24 0.22 A 790D224X(1)050A2(2) 1.0 6 18 0.68 A 790D684X(1)050A2(2) 1.0 6 8.0 1.0 A 790D105X(1)050A2(2) 1.0 6 6.5 1.5 B 790D155X(1)050B2(2) 1.0 6 5.2 2.2 B 790D225X(1)050B2(2) 1.1 6 4.0 3.3 B 790D335X(1)050B2(2) 1.6 6 2.8 4.7 B 790D475X(1)050B2(2) 2.3 6 2.0 6.8 C 790D685X(1)050C2(2) 3.4 6 1.6 10 C 790D106X(1)050C2(2) 5.0 6 1.3 15 C 790D156X(1)050C2(2) 7.5 6 1.0 Notes * Part number definitions: (1) Insert 0 for 20 % tolerance or 9 for 10 % (2) See Ordering Information, packaging code * Extended ratings in bold print Revision: 18-Jun-12 Document Number: 42072 4 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 790D www.vishay.com Vishay Sprague MAXIMUM PERMISSIBLE RIPPLE VOLTAGE AT + 25 C CASE SIZE "B" 30 20 10 10 7 7 5 3 2 35 50 / V 25 40 V 16 V 10 V 6. V 3V 1 0.7 0.5 0.3 0.2 5 3 2 Urms Urms CASE SIZE "A" 30 20 5 35 0 V / 25 40 V 16 V 1 V 6. 0 V 3V 1 0.7 0.5 0.3 0.2 0.1 0.1 0.1K 0.5 1K 5 10K 50 100K 500 0.1K 0.5 1K 5 FREQUENCY IN Hz 10 10 7 7 5 3 2 5 3 2 5 35 0 V / 25 40 16 V V 10 V 6. V 3V 0.5 0.3 0.2 100K 500 50 100K 500 CASE SIZE "D" 30 20 Urms Urms CASE SIZE "C" 0.7 50 FREQUENCY IN Hz 30 20 1 10K 35 50 / V 25 40 V V 1 16 10 V 6. V 3V 0.7 0.5 0.3 0.2 0.1 0.1 0.1K 0.5 1K 5 10K 50 100K 500 0.1K 0.5 FREQUENCY IN Hz 1K 5 10K FREQUENCY IN Hz TYPICAL CURVES OF IMPEDANCE VS FREQUENCY 100 30 6.3 V 35 V 10 10 6.8 F 1 1 F 47 F 1 150 F 6.8 F 0.1 330 F 47 F 22 F 0.1 1K 10K 100K 1M FREQUENCY IN Hz Revision: 18-Jun-12 10M 100M 1K 10K 100K 1M 10M 100M FREQUENCY IN Hz Document Number: 42072 5 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 790D www.vishay.com Vishay Sprague PACKAGING QUANTITIES CASE CODE REEL X/Y AMMO G/H BULK B 500 A 1000 1000 B 1000 1000 250 C 300 (1) 300 (1) 100 D 200 (1) 200 (1) 50 Note (1) Non preferred configuration on request only PERFORMANCE CHARACTERISTICS 1. Operating Temperature: - 55 C to + 85 C with rated voltage UR applied. + 85 C to 125 C with linear voltage derating to category voltage UC (see general information) applied. 2. Capacitance and Tolerance: Capacitance measured at 100 Hz and + 25 C shall be within the specified tolerance limits of the nominal rating. 7. Life Test: 2000 h at + 85 C with rated voltage applied 2000 h at + 125 C with category voltage applied C/C 10 % of initial value IL 1.25 initial limit DF initial limit 8. Humidity Test: 56 days at + 40 C, 90 % relative humidity C/C 8 % of initial value IL initial limit DF initial limit 9. Charge and Discharge Test: 1 million cycles at + 85 C, 0.5 s charge at UR 0.5 s discharge Series resistance < 0.5 C/C 5 % of initial value IL initial limit DF initial limit 3. Reverse Voltage: 15 % of rated voltage at + 25 C 5 % of rated voltage at + 85 C 4. Surge Voltage: 130 % of UR at + 85 C 130 % of UC at + 125 C 5. Impedance at 100 kHz: Measured at + 20 C 5 C, impedance shall not exceed the values listed in datasheet. 6. Stability at low and high temperatures: Capacitance change with temperature, dissipation factor and DC leakage current shall not exceed the limits of the following table. TEMP. CAPACITANCE DISSIPATION CHANGE FACTOR CRUR 1900 IL CRUR > 1900 - 55 C - 10 % + 25 C - + 85 C + 12 % + 125 C + 15 % 9% 11 % 6% 8% 9% 11 % 12 % Revision: 18-Jun-12 14 % LEAKAGE CURRENT 10. Marking: Top: Rating and polarity Front: Type, date code, Sprague trademark 0.01 CR x UR or 1 A whichever is greater 0.1 CR x UR or 10 A whichever is greater 0.125 CR x UR or 12.5 A whichever is greater Document Number: 42072 6 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 790D www.vishay.com Vishay Sprague TAPE AND REEL PACKING Reel packing "A" and "B" cases only (meets IEC 286-2) h O 20 p SPRAGUE 30 MAX. W2 329 - 331 H0 H W0 W1 Ammopacking W t P0 P2 P1 F OD 191 201 Direction of unreel 41 to 45 320 to 330 DESIGNATIONS SYMBOL DIMENSIONS (mm) Pitch of component P 12.7 1.0 Feed hole pitch P0 12.7 0.3 Tape width W 18 (+ 1/- 0.5) Hold down tape width W0 5.0 Hole position W1 9 (+ 0.75/-0.5) Hold down tape position W2 0 (+ 3/-0) Feed hole diameter D0 4.0 0.3 T 0.5 0.2 Tape thickness Component alignment h 02 Lead clinch height H0 16.0 0.5 Hole center to component center P2 6.35 1.3 F P1 CASE A 2.5 + 0.6/- 0.1 5.1 0.7 CASE B 5 + 0.6/- 0.1 3.85 0.7 CASE B 5 + 0.6/- 0.1 3.85 0.7 Reel pack options H = 16.5 H = 18.5 X Y Z X Y Ammopack options H = 16.5 H = 18.5 G H I G H 1000 1000 1000 Lead wire spacing Feed hole center to wire center Quantity per reel/box PRODUCT INFORMATION Quick Reference Guide www.vishay.com/doc?40037 Selector Guide www.vishay.com/doc?49054 Parameter Comparison Guide www.vishay.com/doc?40033 Mounting of Through-Hole Components www.vishay.com/doc?40108 Frequently Asked Questions www.vishay.com/doc?40110 Revision: 18-Jun-12 Document Number: 42072 7 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000