Maxim > Design Support > App Notes > Wireless and RF > APP 5100 Keywords: layout, pcb, mixed signal, rf pcb, board design, board layout, wireless, printed circuit board, stripline, transmission line APPLICATION NOTE 5100 Sep 14, 2011 General Layout Guidelines for RF and Mixed-Signal PCBs By: Michael Bailey Abstract: This application note provides guidelines and suggestions for RF printed-circuit board (PCB) design and layout, including some discussion of mixed-signal applications. The material provides "best practices" guidance, and should be used in conjunction with all other design and manufacturing guidelines that may apply to particular components, PCB manufacturers, and material sets as applicable. This application note applies to all of Maxim's wireless products. For more information, please select a wireless or RF product. Table of Contents Introduction RF Transmission Lines Microstrip Suspended Stripline Coplanar Waveguide (Grounded) Characteristic Impedance Transmission Line Bends and Corner Compensation Layer Changes for Transmission Lines Signal Line Isolation Ground Planes Special Consideration on Bias and Ground Layers Power (Bias) Routing and Supply Decoupling Selection of Decoupling or Bypass Capacitors Bypass Capacitor Layout Considerations Grounding of Shunt Connected Components IC Ground Plane ("Paddle") Click here for an overview of the wireless components used in a typical radio transceiver. Introduction This application note provides guidelines and suggestions for RF printed-circuit board (PCB) design and layout, including some discussion of mixed-signal applications, such as digital, analog, and RF components on the same PCB. The material is arranged by topic areas and provides "best practices" guidance. It should be used in conjunction with all other design and manufacturing guidelines that may apply to particular components, PCB manufacturers, and material sets as applicable. RF Transmission Lines Many of Maxim's RF components require controlled impedance transmission lines that will transport RF power to (or from) IC pins on the PCB. These transmission lines can be implemented on a exterior layer (top or bottom), or buried in an internal layer. Guidelines for these transmission lines include discussions relating to the microstrip, suspended stripline, coplanar waveguide (grounded), and characteristic impedance. It also describes transmission line bends and corner compensation, and layer changes for transmission lines. Microstrip This type of transmission line consists of fixed-width metal routing (the conductor), along with a solid unbroken ground plane located directly underneath (on the adjacent layer). For example, a microstrip on Layer 1 (top metal) requires a solid ground plane on Layer 2 (Figure 1). The width of the routing, the thickness of the dielectric layer, and the type of dielectric determine the characteristic impedance (typically 50 or 75). Page 1 of 14 Figure 1. Microstrip example (isometric view). Suspended Stripline This line consists of a fixed-width routing on an inner layer, with solid ground planes above and below the center conductor. The conductor can be located midway between the ground planes (Figure 2), or it can be offset (Figure 3). This is the appropriate method for RF routing on inner layers. Figure 2. Suspended stripline (end view). Figure 3. Offset suspended stripline. A variant of the stripline, for PCBs with unequal layer thicknesses (end view). Coplanar Waveguide (Grounded) A coplanar waveguide provides for better isolation between nearby RF lines, as well as other signal lines (end view). This medium consists of a center conductor with ground planes on either side and below (Figure 4). Figure 4. A coplanar waveguide provides for better isolation between nearby RF lines and other signal lines. Page 2 of 14 Via "fences" are recommended on both sides of a coplanar waveguide, as shown in Figure 5. This top view provides an example of a row of ground vias on each top metal gound plane on either side of the center conductor. Return currents induced on the top layer are shorted to the underlying ground layer. Figure 5. Via fences are recommended on both sides of a coplanar waveguide. Characteristic Impedance There are several calculators available to properly set the signal conductor line width to achieve the target impedance. However, caution should be used when entering the dielectric constant of the layers. The outer laminated layers of typical PCBs often contain less glass content than the core of the board, and consequently the dielectric constant is lower. For example, FR4 core is generally given as R = 4.2, whereas the outer laminate (prepreg) layers are typically R = 3.8. Examples given below for reference only, metal thickness assumed for 1oz copper (1.4 mils, 0.036mm). Table 1. Examples of Characteristic Impedance Layer Thickness in mils Media Dielectric (mm) Center Conductor in mils (mm) Gap Characteristic Impedance 6 (0.152) 11.5 (0.292) 10 (0.254) 20 (0.508) Prepreg (3.8) 6 (0.152) 25 (0.635) 6 50.6 (0.152) Stripline FR4 (4.5) 12 (0.305) 3.7 (0.094) N/A 50.0 Offset Stripline Prepreg (3.9) 6 (0.152) upper, 10 (0.254) lower 4.8 (0.122) N/A 50.1 Coplanar WG Prepreg (3.8) 6 (0.152) 14 (0.35) 20 (0.50) 49.7 Microstrip Prepreg (3.8) Diff. Pair N/A 50.3 50.0 Transmission Line Bends and Corner Compensation When transmission lines are required to bend (change direction) due to routing constraints, use a bend radius that is at least 3 times the center conductor width. In other words: Bend Radius 3 x (Line Width). This will minimize any charactericstic impedance changes moving through the bend. In cases where a gradually curved bend is not possible, the transmission line can undergo a right-angle bend (noncurved). See Figure 6. However, this must be compensated to reduce the impedance discontinuity caused by the local increase in effective line width going through the bend. A standard compensation method is the angled miter, as illustrated below. The optimum microstrip right-angle miter is given by the formula of Douville and James: Where M is the fraction (%) of the miter compared to the unmitered bend. This formula is independent of the dielectric constant, and is subject to the constraint that w/h 0.25. Page 3 of 14 Similar methods can be employed for other transmission lines. If there is any uncertaintly as to the correct compensation, the bend should be modeled using an electromagnetic simulator if the design requires high-performance transmission lines. Figure 6. When a curved bend is not possible, the transmission line can undergo a right-angle bend. Layer Changes for Transmission Lines When layout constraints required that a transmission line move to a different layer, it is recommended that at least two via holes be used for each transition to minimize the via inductance loading. A pair of vias will effectively cut the transition inductance by 50%, and the largest diameter via should be utilized that is compatible with the transmission line width. For example, on a 15-mil microstrip line, a via diameter (finished plated diameter) of 15 mils to 18 mils would be used. If space does not permit the use of larger vias, then three transition vias of smaller diameter should be used. Signal Line Isolation Care must be taken to prevent unintended coupling between signal lines. Some examples of potential coupling and preventative measures: RF Transmission Lines: Lines should be kept as far apart as possible, and should not be routed in close proximity for extended distances. Coupling between parallel microstrip lines will increase with decreasing separation and increasing parallel routing distance. Lines that cross on separate layers should have a ground plane keeping them apart. Signal lines that will carry high power levels should be kept away from all other lines whenever possible. The grounded coplanar waveguide provides for excellent isolation between lines. It is impractical to achieve isolation better than approximately -45dB between RF lines on small PCBs. High-Speed Digital Signal Lines: These lines should be routed separately on a different layer than the RF signal lines, to prevent coupling. Digital noise (from clocks, PLLs, etc.) can couple onto RF signal lines, and these can be modulated onto RF carriers. Alternatively, in some cases digital noise can be up/down-converted. V CC /Power Lines: These should be routed on a dedicated layer. Adequate decoupling/bypass capcitors should be provided at the main VCC distribution node, as well as at VCC branches. The choice of the bypass capacitances must be made based on the overall frequency response of the RF IC, and the expected frequency distribution nature of any digital noise from clocks and PLLs. These lines should also be separated from any RF lines that will transmit large amounts of RF power. Ground Planes The recommended practice is to use a solid (continuous) ground plane on Layer 2, assuming Layer 1 is used for the RF components and transmission lines. For striplines and offset striplines, ground planes above and below the center conductor are required. These planes must not be shared or assigned to signal or power nets, but must be uniquely allocated to ground. Partial ground planes on a layer, sometimes required by design constraints, must underlie all RF components and transmission lines. Ground planes must not be broken under transmission line routing. Ground vias between layers should be added liberally throughout the RF portion of the PCB. This helps prevent accrual of parasitic ground inductance due to ground-current return paths. The vias also help to prevent cross-coupling from RF and other signal lines across the PCB. Page 4 of 14 Special Consideration on Bias and Ground Layers The layers assigned to system bias (DC supply) and ground must be considered in terms of the return current for the components. The general guidance is to not have signals routed on layers between the bias layer and the ground layer. Figure 7. Incorrect layer assignment: there are signal layers between the bias layer and ground-current return path on ground layer. Bias line noise can be coupled to the signal layers. Figure 8. Better layer assignment: there are no signal layers between the bias and ground return layers. Power (Bias) Routing and Supply Decoupling A common practice is to use a "star" configuration for the power-supply routes, if a component has several supply connections (Figure 9). A larger decoupling capacitor (tens of Fds) is mounted at the "root" of the star, and smaller capacitors at each of the star branches. The value of these latter capacitors depends on the operating frequency range of the RF IC, and their specific functionality (i.e., interstage vs. main supply decoupling). An example is shown below. Page 5 of 14 More detailed image (PDF, 2MB) Figure 9. If a component has several supply connections, the power-supply routes can be arranged in a star configuration. The "star" configuration avoides long ground return paths that would result if all the pins connected to the same bias net were connected in series. A long ground return path would cause a parasitic inductance that could lead to unintended feedback loops. The key consideration with supply decoupling is that the DC supply connections must be electrically defined as AC ground. Selection of Decoupling or Bypass Capacitors Real capacitors have limited effective frequency ranges due to their self-resonant frequency (SRF). The SRF is available from the manufacturer, but sometimes must be characterized by direct measurement. Above the SRF, the capacitor is inductive, and therefore will not perform the decoupling or bypass function. When broadband decoupling is required, standard practice is to use several capacitors of increasing size (capacitance), all connected in parallel. The smaller value capacitors normally have higher SRFs (for example, a 0.2pF value in a 0402 SMT package with an SRF = 14GHz), while the larger values have lower SRFs (for example, a 2pF value in the same package with an SRF = 4GHz). A typical arrangement is depicted in Table 2. Table 2. Useful Frequency Ranges of Capacitors Component Capacitance Package SRF Useful Frequency Range* Ultra-High Range 20pF 0402 2.5GHz 800MHz to 2.5GHz Very High Range 100pF 0402 800MHz 250MHz to 800MHz High Range 1000pF 0402 250MHz 50MHz to 250MHz Midrange 1F 0402 60MHz 100kHz to 60MHz Low Range 10F 0603 600kHz 10kHz to 600kHz Page 6 of 14 *Low end of useful frequency range defined as less than 5 of capacitive reactance. Bypass Capacitor Layout Considerations Since the supply lines must be AC ground, it is important to minimize the parasitic inductance added to the AC ground return path. These parasitic inductances can be caused by layout or component orientation choices, such as the orientation of a decoupling capacitor's ground. There are two basic methods, shown in Figure 10 and Figure 11. Figure 10. This configuration presents the smallest total footprint for the bypass capcitor and related vias. In this configuration, the vias connecting the VCC pad on the top layer to the inner power plane (layer) poentially impede the AC ground current return, forcing a longer return path with resulting higher parasitic inductance. Any AC current flowing into the VCC pin passes through the bypass capcitor to its ground side before returning on the inner ground layer. This configuration presents the smallest total footprint for the bypass capcitor and related vias. Figure 11. This configuration requires more PCB area. In this alternate configuration, the AC ground return paths are not blocked by the power-plane vias. Generally this configuration requires somewhat more PCB area. Grounding of Shunt-Connected Components For shunt-connected (grounded) components (such as power-supply decoupling capacitors), the recommended practice is to use at least two grounding vias for each component (Figure 12). This reduces the effect of via parasitic inductance. Via ground "islands" can be used for groups of shunt-connected components. Page 7 of 14 Figure 12. Using at least two grounding vias for each components reduces the effect of via parasitic inductance. IC Ground Plane ("Paddle") Most ICs require a solid ground plane on the component layer (top or bottom of PCB) directly underneath the component. This ground plane will carry DC and RF return currents through the PCB to the assigned ground plane. The secondary function of this component "ground paddle" is to provide a thermal heatsink, so the paddle should include the maximum number of thru vias that are allowed by the PCB design rules. The example below shows a 5 x 5 array of via holes embedded in the central ground plane (on the component layer) directly under the RF IC (Figure 13). The maximum number of vias that can be accomodated by other layout considerations should be used. These vias are ideally thru-vias (i.e., penetrate all the way through the PCB), and must be plated. If possible, the vias should be filled with thermally conductive paste to enhance the heatsink (the paste is applied after via plating and prior to final board plating). Figure 13. A 5 x 5 array of via holes embedded in the central ground plane directly under the RF IC. Please see our Wireless and RF Products page for more information. Related Parts DS1870 DS4026 MAX12000 MAX12005 MAX1385 MAX1386 MAX1470 MAX1471 MAX1472 MAX1473 MAX1479 MAX19692 MAX19790 MAX19985 MAX19985A MAX19993 MAX19993A LDMOS RF Power-Amplifier Bias Controller 10MHz to 51.84MHz TCXO 1575MHz GPS Front-End Amplifier Satellite IF Switch Dual RF LDMOS Bias Controllers with IC/SPI Interface Dual RF LDMOS Bias Controllers with IC/SPI Interface 315MHz Low-Power, +3V Superheterodyne Receiver 315MHz/434MHz Low-Power, 3V/5V ASK/FSK Superheterodyne Receiver 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range 300MHz to 450MHz Low-Power, Crystal-Based +10dBm ASK/FSK Transmitter 12-Bit, 2.3Gsps Multi-Nyquist DAC 250MHz to 4000MHz Dual, Analog Voltage Variable Attenuator Dual, SiGe, High-Linearity, High-Gain, 700MHz to 1000MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, High-Gain, 700MHz to 1000MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 1200MHz to 1700MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 1200MHz to 2000MHz Downconversion Mixer with ------ Free Free Free Free Free Samples Samples Samples Samples Samples ----- Free Free Free Free Samples Samples Samples Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples Page 8 of 14 MAX19994 MAX19994A MAX19995 MAX19995A MAX19996 MAX19996A MAX19997A MAX19998 MAX19998A MAX19999 MAX2009 MAX2010 MAX2014 MAX2015 MAX2016 MAX2021 MAX2022 MAX2023 MAX2027 MAX2029 MAX2030 MAX2030A MAX2031 MAX2032 MAX2039 MAX2040 MAX2040A MAX2041 MAX2042 MAX2042A MAX2043 MAX2044 LO Buffer/Switch Dual, SiGe, High-Linearity, 1200MHz to 1700MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 1200MHz to 2000MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 1700MHz to 2200MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 1700MHz to 2200MHz Downconversion Mixer with LO Buffer/Switch SiGe, High-Linearity, High-Gain, 2000MHz to 3000MHz Downconversion Mixer with LO Buffer SiGe, High-Linearity, 2000MHz to 3900MHz Downconversion Mixer with LO Buffer Dual, SiGe High-Linearity, High-Gain, 1800MHz to 2900MHz Downconversion Mixer with LO Buffer/Switch SiGe, High-Linearity, 2300MHz to 4000MHz Downconversion Mixer with LO Buffer SiGe, High-Linearity, High-Gain, 3200MHz to 3900MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe High-Linearity, 3000MHz to 4000MHz Downconversion Mixer with LO Buffer 1200MHz to 2500MHz Adjustable RF Predistorter 500MHz to 1100MHz Adjustable RF Predistorter 50MHz to 1000MHz, 75dB Logarithmic Detector/Controller 0.1GHz to 3GHz, 75dB Logarithmic Detector/Controller LF-to-2.5GHz Dual Logarithmic Detector/Controller for Power, Gain, and VSWR Measurements High-Dynamic-Range, Direct Up-/Downconversion, 750MHz to 1200MHz Quadrature Modulator/Demodulator High-Dynamic-Range, Direct Upconversion 1500MHz to 2500MHz Quadrature Modulator High-Dynamic-Range, Direct Up-/Downconversion 1500MHz to 2300MHz Quadrature Mod/Demod IF Digitally Controlled Variable-Gain Amplifier High-Linearity, 815MHz to 1000MHz Upconversion/Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 700MHz to 1000MHz Up/Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 700MHz to 1000MHz Up/Downconversion Mixer with LO Buffer/Switch High-Linearity, 650MHz to 1000MHz Upconversion/Downconversion Mixer with LO Buffer/Switch High-Linearity, 650MHz to 1000MHz Upconversion/Downconversion Mixer with LO Buffer/Switch High-Linearity, 1700MHz to 2200MHz Upconversion/Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 1700MHz to 2200MHz Up/Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 1700MHz to 3000MHz Up/Downconversion Mixer with LO Buffer/Switch High-Linearity, 1700MHz to 3000MHz Upconversion/Downconversion Mixer with LO Buffer/Switch SiGe High-Linearity, 2000MHz to 3000MHz Upconversion/Downconversion Mixer with LO Buffer SiGe, High-Linearity, 1600MHz to 3900MHz Upconversion/Downconversion Mixer with LO Buffer 1700MHz to 3000MHz High-Linearity, Low LO Leakage Base-Station Rx/Tx Mixer SiGe, High-Linearity, 2300MHz to 4000MHz Upconversion/Downconversion Mixer with LO Buffer -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples ------ Free Free Free Free Free Samples Samples Samples Samples Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples Page 9 of 14 MAX2044A MAX2045 MAX2046 MAX2047 MAX2051 MAX2055 MAX2056 MAX2057 MAX2058 MAX2059 MAX2062 MAX2063 MAX2064 MAX2065 MAX2066 MAX2067 MAX2112 MAX2114 MAX2117 MAX2120 MAX2121 MAX2135A MAX2136 MAX2140 MAX2141 MAX2150 MAX2160 MAX2160EBG MAX2161 MAX2161S MAX2162 MAX2162S MAX2165 MAX2169 MAX2170 MAX2171 MAX2172 MAX2180 MAX2202 MAX2203 MAX2204 MAX2205 MAX2206 MAX2207 MAX2208 MAX2209 MAX2209A MAX2232 MAX2233 MAX2235 MAX2240 MAX2242 SiGe, High-Linearity, 3000MHz to 4000MHz Upconversion/Downconversion Mixer with LO Buffer High-Gain Vector Multipliers High-Gain Vector Multipliers High-Gain Vector Multipliers SiGe, High-Linearity, 850MHz to 1550MHz Up/Downconversion Mixer with LO Buffer Digitally Controlled, Variable-Gain, Differential ADC Driver/Amplifier 800MHz to 1000MHz Variable-Gain Amplifier with Analog Gain Control 1300MHz to 2700MHz Variable-Gain Amplifier with Analog Gain Control 700MHz to 1200MHz High-Linearity, SPI-Controlled DVGA with Integrated Loopback Mixer 1700MHz to 2200MHz, High-Linearity, SPI-Controlled DVGA with Integrated Loopback Mixer Dual 50MHz to 1000MHz High-Linearity, Serial/Parallel-Controlled Analog/Digital VGA Dual 50MHz to 1000MHz High-Linearity, Serial/Parallel-Controlled Digital VGA 50MHz to 1000MHz, High-Linearity, Serial/Analog-Controlled VGA 50MHz to 1000MHz High-Linearity, Serial/Parallel-Controlled Analog/Digital VGA 50MHz to 1000MHz High-Linearity, Serial/Parallel-Controlled Digital VGA 50MHz to 1000MHz High-Linearity, Serial/Analog-Controlled VGA Complete, Direct-Conversion Tuner for DVB-S2 Applications DBS Direct Downconverter Complete, Direct-Conversion Tuner for MMDS Applications Complete, Direct-Conversion Tuner for DVB-S and Free-to-Air Applications Complete Direct-Conversion L-Band Tuner ISDB-T/DVB-T Diversity Tuner ISDB-T/DVB-T Low-IF Tuner Complete SDARS Receiver Low-Power XM Satellite Radio Receiver Wideband I/Q Modulator with Sigma-Delta Fractional-N Synthesizer ISDB-T Single-Segment Low-IF Tuners ISDB-T Single-Segment Low-IF Tuners ISDB-T 1- and 3-Segment Low-IF Tuners ISDB-T 1- and 3-Segment Low-IF Tuners ISDB-T 1- and 3-Segment Low-IF Tuners ISDB-T 1- and 3-Segment Low-IF Tuners Single-Conversion DVB-H Tuner Multiband Tuner for Mobile Multimedia Applications Direct-Conversion to Low-IF Tuners for Digital Audio Broadcast Direct-Conversion to Low-IF Tuners for Digital Audio Broadcast Direct-Conversion to Low-IF Tuner for Digital Audio Broadcast AM/FM Car Antenna Low-Noise Amplifier RMS Power Detector RMS Power Detector RF Power Detector RF Power Detectors in UCSP RF Power Detectors in UCSP RF Power Detectors in UCSP RF Power Detectors in UCSP RF Power Detector RF Power Detector with Shutdown Control 900MHz ISM-Band, 250mW Power Amplifiers with Analog or Digital Gain Control 900MHz ISM-Band, 250mW Power Amplifiers with Analog or Digital Gain Control +3.6V, 1W Autoramping Power Amplifier for 900MHz Applications 2.5GHz, +20dBm Power Amplifier IC in UCSP Package 2.4GHz to 2.5GHz Linear Power Amplifier ----- Free Free Free Free Samples Samples Samples Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples ---------- Free Free Free Free Free Free Free Free Free Samples Samples Samples Samples Samples Samples Samples Samples Samples -- Free Samples -- Free Samples ------- Free Free Free Free Free Free Samples Samples Samples Samples Samples Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples Page 10 of 14 MAX2265 MAX2306 MAX2308 MAX2309 MAX2335 MAX2338 MAX2370 MAX2371 MAX2373 MAX2410 MAX2411A MAX2470 MAX2471 MAX2472 MAX2473 MAX2500B MAX2510 MAX2511 MAX2547 MAX2548 MAX2550 MAX2557 MAX2557A MAX2597 MAX2598 MAX2599 MAX2601 MAX2602 MAX2605 MAX2606 MAX2607 MAX2608 MAX2609 MAX2611 MAX2620 MAX2622 MAX2623 MAX2624 MAX2630 MAX2631 MAX2632 MAX2633 MAX2634 MAX2640 MAX2641 MAX2642 MAX2643 MAX2644 MAX2645 MAX2650 MAX2654 MAX2655 MAX2656 MAX2657 MAX2658 MAX2659 MAX2660 MAX2661 MAX2663 MAX2664 2.7V, Single-Supply, Cellular-Band Linear Power Amplifiers CDMA IF VGAs and I/Q Demodulators with VCO and Synthesizer CDMA IF VGAs and I/Q Demodulators with VCO and Synthesizer CDMA IF VGAs and I/Q Demodulators with VCO and Synthesizer 450MHz CDMA/OFDM LNA/Mixer Triple/Dual-Mode CDMA LNA/Mixers Complete 450MHz Quadrature Transmitter LNAs with Step Attenuator and VGA LNAs with Step Attenuator and VGA Low-Cost RF Up/Downconverter with LNA and PA Driver Low-Cost RF Up/Downconverter with LNA and PA Driver 10MHz to 500MHz, VCO Buffer Amplifiers with Differential Outputs 10MHz to 500MHz, VCO Buffer Amplifiers with Differential Outputs 500MHz to 2500MHz, VCO Buffer Amplifiers 500MHz to 2500MHz, VCO Buffer Amplifiers Complete Cellular Baseband-to-RF Transmitter with PA Low-Voltage IF Transceiver with Limiter RSSI and Quadrature Modulator Low-Voltage IF Transceiver with Limiter and RSSI WCDMA/HSPA Band I RF-to-Bits Femto-Basestation Radio Receiver Quad-Band TDD-WCDMA RF-to-Bits Radio Receiver Complete Single-Chip Femtocell Radio Transceiver Multiband, Multimode RF-to-Bits Femto-Basestation Radio Receiver Multiband, Multimode RF-to-Bits CDMA Femto-Basestation Radio Receiver Femto-Basestation Bits-to-RF Radio Transmitter Quad-Band TDD-WCDMA Bits-to-RF Radio Transmitter Femto Basestation Bits-to-RF Radio Transmitter 3.6V, 1W RF Power Transistors for 900MHz Applications 3.6V, 1W RF Power Transistors for 900MHz Applications 45MHz to 650MHz, Integrated IF VCOs with Differential Output 45MHz to 650MHz, Integrated IF VCOs with Differential Output 45MHz to 650MHz, Integrated IF VCOs with Differential Output 45MHz to 650MHz, Integrated IF VCOs with Differential Output 45MHz to 650MHz, Integrated IF VCOs with Differential Output DC-to-Microwave, Low-Noise Amplifier 10MHz to 1050MHz Integrated RF Oscillator with Buffered Outputs Monolithic Voltage Controlled Oscillators Monolithic Voltage Controlled Oscillators Monolithic Voltage Controlled Oscillators VHF-to-Microwave, +3V, General-Purpose Amplifiers VHF-to-Microwave, +3V, General-Purpose Amplifiers VHF-to-Microwave, +3V, General-Purpose Amplifiers VHF-to-Microwave, +3V, General-Purpose Amplifiers 315MHz/433MHz Low-Noise Amplifier for Automotive RKE 300MHz to 2500MHz SiGe Ultra-Low-Noise Amplifiers 300MHz to 2500MHz SiGe Ultra-Low-Noise Amplifiers 900MHz SiGe, High-Variable IP3, Low-Noise Amplifier 900MHz SiGe, High-Variable IP3, Low-Noise Amplifier 2.4GHz SiGe, High IP3 Low-Noise Amplifier 3.4GHz to 3.8GHz SiGe Low-Noise Amplifier/PA Predriver DC-to-Microwave, +5V Low-Noise Amplifier 1575MHz/1900MHz Variable-IP3 Low-Noise Amplifiers 1575MHz/1900MHz Variable-IP3 Low-Noise Amplifiers 1575MHz/1900MHz Variable-IP3 Low-Noise Amplifiers GPS/GNSS Low-Noise Amplifiers GPS/GNSS Low-Noise Amplifiers GPS/GNSS Low-Noise Amplifier 400MHz to 2.5GHz Upconverters 400MHz to 2.5GHz Upconverters 400MHz to 2.5GHz Upconverters VHF/UHF Low-Noise Amplifiers ---------------- Free Free Free Free Free Free Free Free Free Free Free Free Free Free Free Samples Samples Samples Samples Samples Samples Samples Samples Samples Samples Samples Samples Samples Samples Samples ----- Free Free Free Free Samples Samples Samples Samples ------------------- Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples ------- Free Free Free Free Free Free Samples Samples Samples Samples Samples Samples ------- Free Free Free Free Free Free Samples Samples Samples Samples Samples Samples ----- Free Free Free Free Samples Samples Samples Samples Page 11 of 14 MAX2665 MAX2666 MAX2667 MAX2668 MAX2669 MAX2670 MAX2671 MAX2673 MAX2674 MAX2676 MAX2680 MAX2681 MAX2682 MAX2685 MAX2686 MAX2686L MAX2687 MAX2687L MAX2688 MAX2689 MAX2690 MAX2691 MAX2692 MAX2693 MAX2694 MAX2695 MAX2740 MAX2745 MAX2750 MAX2750AUA MAX2751 MAX2752 MAX2769 MAX2769B MAX2828 MAX2829 MAX2830 MAX2831 MAX2832 MAX2837 MAX2838 MAX2839 MAX2839AS MAX2842 MAX2850 MAX2851 MAX2852 MAX2900 MAX2901 MAX2902 MAX2903 MAX2904 MAX2990 MAX3518 MAX3524 MAX3541 MAX3542 MAX3543 MAX3544 VHF/UHF Low-Noise Amplifiers Tiny Low-Noise Amplifiers for HSPA/LTE GPS/GNSS Ultra-Low-Noise-Figure LNAs Tiny Low-Noise Amplifiers for HSPA/LTE GPS/GNSS Ultra-Low-Noise-Figure LNAs GPS/GNSS Front-End Amplifier 400MHz to 2.5GHz Upconverters 400MHz to 2.5GHz Upconverters GPS/GNSS LNAs with Antenna Switch and Bias GPS/GNSS LNAs with Antenna Switch and Bias 400MHz to 2.5GHz, Low-Noise, SiGe Downconverter Mixers 400MHz to 2.5GHz, Low-Noise, SiGe Downconverter Mixers 400MHz to 2.5GHz, Low-Noise, SiGe Downconverter Mixers Low-Cost, 900MHz, Low-Noise Amplifier and Downconverter Mixer GPS/GNSS Low-Noise Amplifiers GPS/GNSS Low-Noise Amplifier with Integrated LDO GPS/GNSS Low-Noise Amplifiers GPS/GNSS Low-Noise Amplifier with Integrated LDO GPS/GNSS Low-Noise Amplifiers GPS/GNSS Low-Noise Amplifier Low-Noise, 2.5GHz Downconverter Mixer GPS/GNSS Low-Noise Amplifier for L2 Band WLAN/WiMax Low-Noise Amplifiers GPS/GNSS Low-Noise Amplifier GPS/GNSS Low-Noise Amplifiers WLAN/WiMax Low-Noise Amplifiers Integrated GPS Receiver and Synthesizer Single-Chip Global Positioning System Front-End Downconverter 2.4GHz Monolithic Voltage-Controlled Oscillators 2.4GHz Monolithic Voltage-Controlled Oscillator for Automotive 2.4GHz Monolithic Voltage-Controlled Oscillators 2.4GHz Monolithic Voltage-Controlled Oscillators Universal GPS Receiver Universal GPS Receiver Single-/Dual-Band 802.11a/b/g World-Band Transceiver ICs Single-/Dual-Band 802.11a/b/g World-Band Transceiver ICs 2.4GHz to 2.5GHz 802.11g/b RF Transceiver with PA and Rx/Tx/Diversity Switch 2.4GHz to 2.5GHz, 802.11g RF Transceivers with Integrated PA 2.4GHz to 2.5GHz, 802.11g RF Transceivers with Integrated PA 2.3GHz to 2.7GHz Wireless Broadband RF Transceiver 3.3GHz to 3.8GHz Wireless Broadband RF Transceiver 2.3GHz to 2.7GHz MIMO Wireless Broadband RF Transceiver 2.3GHz to 2.7GHz MIMO Wireless Broadband RF Transceiver 3.3GHz to 3.9GHz MIMO Wireless Broadband RF Transceiver 5GHz, 4-Channel MIMO Transmitter 5GHz, 5-Channel MIMO Receiver 5GHz Receiver 200mW Single-Chip Transmitter ICs for 868MHz/915MHz ISM Bands 200mW Single-Chip Transmitter ICs for 868MHz/915MHz ISM Bands 200mW Single-Chip Transmitter ICs for 868MHz/915MHz ISM Bands 200mW Single-Chip Transmitter ICs for 868MHz/915MHz ISM Bands 200mW Single-Chip Transmitter ICs for 868MHz/915MHz ISM Bands 10kHz to 490kHz OFDM-Based Power Line Communications Modem DOCSIS 3.0 Upstream Amplifier Low-Noise, High-Linearity Broadband Amplifier Complete Single-Conversion Television Tuner Complete Single-Conversion Television Tuner Multiband Analog and Digital Television Tuner Multiband Digital Television Tuner -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples ------- Free Free Free Free Free Free Samples Samples Samples Samples Samples Samples ----- Free Free Free Free Samples Samples Samples Samples ----------------- Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Free Samples Page 12 of 14 MAX3580 MAX3654 MAX4000 MAX4001 MAX4002 MAX4987AE MAX4987BE MAX5879 MAX5894 MAX66901-K00 MAX7030 MAX7031 MAX7032 MAX7033 MAX7034 MAX7036 MAX7042 MAX7044 MAX7049 MAX7057 MAX7058 MAX7060 MAX8805 MAX8805W MAX8805X MAX8805Y MAX8805Z MAX9930 MAX9931 MAX9932 MAX9933 MAX9947 MAX9957 MAX9981 MAX9982 MAX9984 MAX9985 MAX9985A MAX9986 MAX9986A MAX9987 MAX9988 MAX9989 MAX9990 MAX9993 Direct-Conversion TV Tuner 47MHz to 870MHz Analog CATV Transimpedance Amplifier 2.5GHz 45dB RF-Detecting Controllers 2.5GHz 45dB RF-Detecting Controllers 2.5GHz 45dB RF-Detecting Controllers Overvoltage-Protection Controller with USB ESD Protection Overvoltage-Protection Controller with USB ESD Protection 14-Bit, 2.3Gsps Direct RF Synthesis DAC with Selectable Frequency Response 14-Bit, 500Msps, Interpolating and Modulating Dual DAC with CMOS Inputs High-Frequency Developers Kit for ISO 14443B and ISO 15693 RFID Keys Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with FractionalN PLL Low-Cost, 308MHz, 315MHz, and 433.92MHz FSK Transceiver with FractionalN PLL Low-Cost, Crystal-Based, Programmable, ASK/FSK Transceiver with Fractional-N PLL 315MHz/433MHz ASK Superheterodyne Receiver with AGC Lock 315MHz/434MHz ASK Superheterodyne Receiver 300MHz to 450MHz ASK Receiver with Internal IF Filter 308MHz/315MHz/418MHz/433.92MHz Low-Power, FSK Superheterodyne Receiver 300MHz to 450MHz High-Efficiency, Crystal-Based +13dBm ASK Transmitter High-Performance, 288MHz to 945MHz ASK/FSK ISM Transmitter 300MHz to 450MHz Frequency-Programmable ASK/FSK Transmitter 315MHz/390MHz Dual-Frequency ASK Transmitter 280MHz to 450MHz Programmable ASK/FSK Transmitter 600mA/650mA PWM Step-Down Converters in 2mm x 2mm WLP for WCDMA PA Power 600mA/650mA PWM Step-Down Converters in 2mm x 2mm WLP for WCDMA PA Power 600mA/650mA PWM Step-Down Converters in 2mm x 2mm WLP for WCDMA PA Power 600mA/650mA PWM Step-Down Converters in 2mm x 2mm WLP for WCDMA PA Power 600mA/650mA PWM Step-Down Converters in 2mm x 2mm WLP for WCDMA PA Power 2MHz to 1.6GHz 45dB RF-Detecting Controllers and RF Detector 2MHz to 1.6GHz 45dB RF-Detecting Controllers and RF Detector 2MHz to 1.6GHz 45dB RF-Detecting Controllers and RF Detector 2MHz to 1.6GHz 45dB RF-Detecting Controllers and RF Detector AISG Integrated Transceiver Fast Dual Driver for ATE with Waveform Shaping 825MHz to 915MHz, Dual SiGe High-Linearity Active Mixer 825MHz to 915MHz, SiGe High-Linearity Active Mixer SiGe High-Linearity, 400MHz to 1000MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 700MHz to 1000MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 700MHz to 1000MHz Downconversion Mixer with LO Buffer/Switch SiGe High-Linearity, 815MHz to 995MHz Downconversion Mixer with LO Buffer/Switch SiGe High-Linearity, 815MHz to 1000MHz Downconversion Mixer with LO Buffer/Switch +14dBm to +20dBm LO Buffers/Splitters with 1dB Variation +14dBm to +20dBm LO Buffers/Splitters with 1dB Variation +14dBm to +20dBm LO Buffers with 1dB Variation +14dBm to +20dBm LO Buffers with 1dB Variation High-Linearity 1700MHz to 2200MHz Down-Conversion Mixer with LO Buffer/Switch ------- Free Free Free Free Free Free Samples Samples Samples Samples Samples Samples -- Free Samples -- Free Samples -- Free Samples -- Free Samples ----- Free Free Free Free Samples Samples Samples Samples ------ Free Free Free Free Free Samples Samples Samples Samples Samples ---------- Free Free Free Free Free Free Free Free Free Samples Samples Samples Samples Samples Samples Samples Samples Samples -- Free Samples -- Free Samples -- Free Samples ------ Free Free Free Free Free Samples Samples Samples Samples Samples Page 13 of 14 MAX9994 MAX9995 MAX9995A MAX9996 SiGe High-Linearity, 1400MHz to 2200MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 1700MHz to 2700MHz Downconversion Mixer with LO Buffer/Switch Dual, SiGe, High-Linearity, 1700MHz to 2200MHz Downconversion Mixer with LO Buffer/Switch SiGe High-Linearity, 1700MHz to 2200MHz Downconversion Mixer with LO Buffer/Switch -- Free Samples -- Free Samples -- Free Samples Automatic Updates Would you like to be automatically notified when new application notes are published in your areas of interest? Sign up for EEMailTM. More Information For Technical Support: http://www.maxim-ic.com/support For Samples: http://www.maxim-ic.com/samples Other Questions and Comments: http://www.maxim-ic.com/contact Application Note 5100: http://www.maxim-ic.com/an5100 AN5100, AN 5100, APP5100, Appnote5100, Appnote 5100 Copyright (c) by Maxim Integrated Products Additional Legal Notices: http://www.maxim-ic.com/legal Page 14 of 14