POWER
SIL/SMT40C2 Series
C-Class Non-Isolated
Total Power: 40 Amps
Input Voltage: 4.5 - 13.8 Vdc
# of Outputs: Single
SPECIAL FEATURES
40 A current rating
Input voltage range: 4.5 - 13.8 Vdc
Output voltage: 0.6 - 5 V
Industry-leading value
Cost optimized design
Excellent transient response
Output enable
output voltage adjustability
path for future upgrades
Supports silicon voltage migration
Reduced design-in and qual time
RoHS compliant
SAFETY
UL, cUL CAN/CSA 22.2 No.
E139421 UL6950 File No. TBD
TÜV Product Service (EN60950)
Certicate No. TBD
CB report and certicate to
IEC60950
Electrical Specications
Input
Input voltage ra nge 4.5 - 13.8 Vdc
Input current Minimum load
Remote OFF
50 mA
5 mA
Input current (max.) See Note 3 25 A @ lo max.
Start-up time Remote ON/OFF 3 ms
Output
Output voltage See Note 5 0.6 - 5 V
Output setpoint accuracy 0.1% trim resistors ±1.0%
Line regulation Low line to high line ±0.2%
Load regulation Full load to min. load ±0.5%
Min./max. load 0 A/40 A
Overshoot At turn-on 0.5% max.
Undershoot At turn-off 100 mV max.
Ripple and noise
5 Hz to 20 MHz
See Note 1 25 mV
Vin = 5 V, Vout = 2.5 V
Transient response See Note 1, 2 130 mV max. deviation 50 μs
recovery to within regulation band
General
Efciency (high input) Vin = 5 V, Vo = 2.5 V, lo = 20 A 94%
Switching frequency Fixed 500 kHz
Material ammability UL94V-0
Weight 17 g (0.06 oz.)
MTBF 12 V @ 40 °C, 100% load
Bellcore 332
6,749,409 hours
Coplanarity Surface mount models 150 μm
Data Sheet
SIL/SMT40C2 Series Data Sheet
Environmental Specications
Thermal performance Operating ambient temperature -0 °C to +70 °C
See Note 5 Non-operating temperature -40 °C to +125 °C
Protection
Short-circuit Hiccup, non-latching
Overvoltage protection Hiccup, non-latching
Recommended System Capacitance
Input See Note 6 0 μF
Output See Note 7 0 μF
Output Voltage Adjustment
The ultra-wide output voltage trim range offers major advantages to users
who select the SIL40C2 series. It is no longer necessary to purchase a variety
of modules in order to cover different output voltages. The output voltage can
be trimmed in a range of 0.6-5 V. When the SIL40C2 converter leaves the
factory, the output has been adjusted to the default voltage of 0.6 V.
Ordering Information
Model
Number (3,5)
Input
Voltage
Output
Voltage
Output Current
(Min.)
Output Current
(Max.)
Efficiency
(Typical)
Regulation
Line Load
SIL40C2-00SADJ-VJ 4.5 - 13.8 Vdc 0.6 - 5 V 0 A 40 A 94% ±0.2% ±0.5%
SIL40C2-00SADJHJ 4.5 - 13.8 Vdc 0.6 - 5 V 0 A 40 A 94% ±0.2% ±0.5%
SMT40C2-00SADJJ 4.5 - 13.8 Vdc 0.6 - 5 V 0 A 40 A 94% ±0.2% ±0.5%
Notes:
1. Measured as per recommended system capacitance.
2. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.75 lo to full lo and full lo to 0.75.
3. External input fusing is recommended.
4. Additional part numbers may be available with different output voltages.
5. Airflow dependent, 100 LFM minimum required.
6. No capacitors needed for ripple current stability.
7. No capacitors needed for stability.
8. NOTICE: Some models do not support all options. Please contact your local Artesyn Embedded
Technologies representative or use the on-line model number search tool at
http://www.Artesyn.com/power to find a suitable alternative.
9. To order a Horizontal Mounting option with a pin length of 0.165”, please use model
SIL40C2-00S-HP5.
Part Number System with Options
SIL 40 C 2 - 00 SADJ - V J
Product Family
SIL = Single In Line
SMT = Surface Mount
Output Voltage
Single Adjustable
Output
Performance
C = Cost
Optimized
Input Voltage
00 = 4.5 - 13.8 V
Generation
Blank = Standard
2 = Increased
current density
RoHS Compliance
J = Pb free (RoHS
6/6 compliant)
Mounting Option
V = Vertical
H = Horizontal
(Applicable to SIL
version only)
Rated Output
Current
06 = 6 Amp
15 = 15 Amp
20 = 20 Amp
30 = 30 Amp
40 = 40 Amp
Standard Application Drawing
7,8
10,11
6
9
5
1,2,3
4
SIL40C2
Enable
Vin
GND
Rtrim
(for trim
down)
Cout R
L
O
A
D
Power Good
Vout
+R sense
Cin
SIL/SMT40C2 Series Data Sheet
Mechanical Drawings
0.100 (2.54)
1.050 (26.67)
9 PLACES
1.100 (27.94)
1.200 (30.48)
0.050 (1.27) REF
0.140 (3.56) TYP
PIN 1
0.050 (1.27) TYP
0.255 (6.48)
0.110 (2.79)
0.427 (10.85)
0.025 (0.64) ±.001
SQ PINS TYP
0.062 (1.57) REF
0.100 (2.54) TYP
1.100 (27.94)
1.200 (30.48)
PIN 1
0.255 (6.48)
0.110 (2.79) REF
0.468 (11.89)
0.062 (1.57) REF
.150 (3.81) TYP
0.025 (0.64) ±.001
SQ PINS TYP
13 PLACES
2X 1.050 (26.67)
0.100 (2.54) REF
0.050 (1.27) REF
1.000 (25.40)
2X
0.050 (1.27)
0.100 (2.54) TYP
9 PLACES
Vertical Mount
Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25)
Horizontal Mount
Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25)
SIL/SMT40C2 Series Data Sheet
WORLDWIDE OFFICES
Americas
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
For more information: www.artesyn.com/power
For support: productsupport.ep@artesyn.com
www.artesyn.com
While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn
Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use
of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn
Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc.
All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective
owners. © 2015 Artesyn Embedded Technologies, Inc. SIL/SMT40C2 Series 24Mar2015
Mating Connectors
Mechanical Drawings
1.100 (27.94)
1.200 (30.48)
PIN 1
0.255 (6.48)
0.110 (2.79) REF
0.442 (11.23)
0.062 (1.57) REF
0.125 (3.18) TYP
2X 1.050 (26.67)
0.100 (2.54) REF
0.050 (1.27) REF
1.000 (25.40)
2X
0.050 (1.27)
0.100 (2.54) TYP
9 PLACES
Surface Mount
Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25)
Pin Assignments
Pin Function
1 Vout
2 Vout
3 Vout
4 Trim
5 Enable
6 Power Good
7 Ground
8 Ground
9 (+) Sense
10 Vin
11 Vin
12 Mech Pin (Horz/SMT only)
13 Mech Pin (Horz/SMT only)