GN
125
GN-RELAYS
ULTRA-SMALL PACKAGE
SLIM POLARIZED RELAY
5.70±0.3
.224±.012
10.60±0.3
.417±.012
9.00±0.3
.354±.012
5.70±0.3
.224±.012
10.60±0.3
.417±.012
Max.10.00
.394
mm inch
FEATURES
• Compact slim body saves space
Thanks to the small surface area of 5.7
mm
×
10.6 mm .224 inch
×
.417 inch and
low height of 9.0 mm .354 inch, the pack-
aging density can be increased to allow
for much smaller designs.
• Outstanding surge resistance.
Surge withstand between open contacts:
1,500 V 10
×
160
µ
s (FCC part 68)
Surge withstand between contacts and
coil: 2,500 V 2
×
10
µ
s (Bellcore)
• The use of twin cr ossbar contacts en-
sures high contact reliability.
AgPd contact is used because of its good
sulfide resistance. Adopting low-gas
molding material. Coil assembly molding
technology which avoids generating vola-
tile gas from coil.
• Increased packaging density
Due to highly efficient magnetic circuit de-
sign, leakage flux is reduced and changes
in electrical characteristics from compo-
nents being mounted close-together are
minimized. This all means a packaging
density higher than ever before.
• Nominal operating power: 140 mW
• Outstanding vibration and shock re-
sistance.
Functional shock resistance:
750 m/s
2
{75G}
Destructive shock resistance:
1,000 m/s
2
{100G}
Functional vibration resistance:
10 to 55 Hz (at double amplitude of 3.3
mm .130 inch)
Destructive vibration resistance:
10 to 55 Hz (at double amplitude of 5 mm
.197 inch)
SPECIFICATIONS
Contact
Remarks:
* Specifications will vary with foreign standards certification ratings.
*
1
Measurement at same location as "Initial breakdown voltage" section.
*
2
Detection current: 10mA.
*
3
Nominal voltage applied to the coil, excluding contact bounce time.
*
4
By resistive method, nominal v oltage applied to the coil; contact carrying current:
1 A.
*
5
Half-wave pulse of sine wave: 6 ms; detection time: 10
µ
s.
*
6
Half-wave pulse of sine wave: 6 ms.
*
7
Detection time: 10
µ
s.
*
8
Refer to 5. Conditions for operation, transpor t and storage mentioned in
AMBIENT ENVIRONMENT (Page 61)
Characteristics
Notes:
❇
1 This value can change due to the s witching frequency , environmental conditions,
and desired reliability level, therefore it is recommended to check this with the
actual load.
❇
2 The upper limit for the ambient temperature is the maximum temperature that
can satisfy the coil temperature rise. Under the packing condition, allowable
temperature range is from –40 to +70
°
C –40
°
to +158
°
F.
Arrangement 2 Form C
Initial contact resistance, max.
(By voltage drop 6 V DC 1A ) 100 m
Ω
Contact material Stationary: AgPd+A u clad
Movable: AgPd
Rating
Nominal switching capacity
(resistive load) 1 A 30 V DC
0.3 A 125 V AC
Max. switching power
(resistive load) 30 W, 37.5 V A
Max. switching voltage 110 V DC, 125 V AC
Max. switching current 1 A
Min. switching capacity
❇
1 10
µ
A 10 mV DC
Nominal
operating
power
Single side stable 140mW (1.5 to 12 V DC)
230mW (24 V DC)
1 coil latching 100mW (1.5 to 12 V DC)
120mW (24 V DC)
Expected
life (min.
operations)
Mechanical (at 180 cpm) 5
×
10
7
Electrical
(at 20 cpm)
1 A 30 V DC
resistive 10
5
0.3 A 125 V AC
resistive 10
5
Initial insulation resistance*
1
Min. 1,000M
Ω
(at 500V DC)
Initial
breakdown
voltage*
2
Between open contacts 750 Vrms for 1min.
Between contact sets 1,000 Vrms for 1min.
Between contacts and coil 1,500 Vrms for 1min.
Initial surge
voltage
Between open contacts
(10
×
160
µ
s) 1,500 V (FCC Part 68)
Between contacts and coil
(2
×
10
µ
s) 2,500 V (Bellcore)
Operate time [Set time]*
3
(at 20
°
C) Max. 4 ms (Approx. 2 ms)
[Max. 4 ms (Approx. 2 ms)]
Release time (without diode)
[Reset time]*
3
(at 20
°
C) Max. 4 ms (Approx. 1 ms)
[Max. 4 ms (Approx. 2 ms)]
Temperature rise*
4
(at 20
°
C) Max. 50
°
C
Shock resistance Functional*
5
Min. 750 m/s
2
{75G]
Destructive*
6
Min. 1,000 m/s
2
{100G]
Vibration resistance Functional*
7
10 to 55 Hz at double
amplitude of 3.3 mm
Destructive 10 to 55 Hz at double
amplitude of 5 mm
Conditions for opera-
tion, transport and
storage*
8
(Not freezing and con-
densing at low tem-
perature)
Ambient
temperature
❇
2–40
°
C to 85
°
C
–40
°
F to 185
°
F
Humidity 5 to 85% R.H.
Unit weight Approx. 1 g.035 oz
TESTING
GN
126
TYPICAL APPLICATIONS
• Telephone exchange, transmission
equipment
• Communications devices
• Measurement devices
• Home appliances, and audio/visual
equipment
• Handheld and portable products
ORDERING INFORMATION
200A Z1HEx. AGN
Contact arrangement
Terminal shapeOperating function Packing style
Coil voltage (DC)
Nil: Standard PC board terminal
A: Surface-mount terminal A type
S: Surface-mount terminal S type
2: 2 Form C 0: Single side stable
1: 1 coil latching
Type of operation
0: Standard type
(B.B.M.)
Nil: Tube packing
Z:
Tape and reel packing
(piked from 5/6/7/8
pin side)
1H: 1.5V
03
: 3V
4H: 4.5V
06
: 6V
09
: 9V
12
: 12V
24
: 24V
Note: Tape and reel packing symbol “-Z” is not marked on the relay. “X” type tape and reel packing (picked from 1/2/3/4-pin side) is also available. Suffix “X” instead of “Z”.
TYPES AND COIL DATA (at 20
°
C 68
°
F)
(1) Standard PC board terminal
1) Standard packing: 50 pcs. in an inner package (tube); 1,000 pcs. in an outer package
2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
(2) Surface-mount terminal
❍
: For each surface-mounted terminal variation, input the following letter.
A type: A, S type: S
1) Standard packing: 50 pcs.(tube), 500pcs. (tape and reel)in an inner package; 1,000 pcs. in an outer package
2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
Operating
Function
Part No. Coil Rating,
V DC
Pick-up volt-
age, V DC
(max.)
(initial)
Drop-out
voltage,
V DC (min.)
(initial)
Nominal
operating
current,
mA (
±
10%)
Coil resistance,
Ω
(
±
10%) Nominal
operating
power, mW
Max. allowable
voltage,
V DC
Standard PC
board terminal
Single side
stable
AGN2001H 1.5 1.13 0.15 93.8 16 140 2.25
AGN20003 3 2.25 0.3 46.7 64.2 140 4.5
AGN2004H 4.5 3.38 0.45 31 145 140 6.75
AGN20006 6 4.5 0.6 23.3 257 140 9
AGN20009 9 6.75 0.9 15.5 579 140 13.5
AGN20012 12 9 1.2 11.7 1,028 140 18
AGN20024 24 18 2.4 9.6 2,504 230 28.8
Operating
Function
Part No. Coil Rating,
V DC Set voltage,
V DC (max.)
(initial)
Reset voltage ,
V DC (max.)
(initial)
Nominal
operating
current,
mA (
±
10%)
Coil resistance,
Ω
(
±
10%) Nominal
operating
power, mW
Max. allowable
voltage,
V DC
Standard PC
board terminal
1 coil latching
AGN2101H 1.5 1.13 1.13 66.7 22.5 100 2.25
AGN21003 3 2.25 2.25 33.3 90 100 4.5
AGN2104H 4.5 3.38 3.38 22.2 202.5 100 6.75
AGN21006 6 4.5 4.5 16.7 360 100 9
AGN21009 9 6.75 6.75 11.1 810 100 13.5
AGN21012 12 9 9 8.3 1,440 100 18
AGN21024 24 18 18 5.0 4,800 120 36
Operating
Function
Part No. Coil Rating,
V DC
Pick-up
voltage,
V DC (max.)
(initial)
Drop-out
voltage,
V DC (min.)
(initial)
Nominal
operating
current,
mA (
±
10%)
Coil
resistance,
Ω
(
±
10%)
Nominal
operating
power,
mW
Max.
allowable
voltage,
V DC
Tube packing Tape and reel
packing
Single side
stable
AGN200
❍
1H AGN200
❍
1HZ 1.5 1.13 0.15 93.8 16 140 2.25
AGN200
❍
03 AGN200
❍
03Z 3 2.25 0.3 46.7 64.2 140 4.5
AGN200
❍
4H AGN200
❍
4HZ 4.5 3.38 0.45 31 145 140 6.75
AGN200
❍
06 AGN200
❍
06Z 6 4.5 0.6 23.3 257 140 9
AGN200
❍
09 AGN200
❍
09Z 9 6.75 0.9 15.5 579 140 13.5
AGN200
❍
12 AGN200
❍
12Z 12 9 1.2 11.7 1,028 140 18
AGN200
❍
24 AGN200
❍
24Z 24 18 2.4 9.6 2,504 230 28.8
GN
127
❍
: For each surface-mounted terminal variation, input the following letter.
A type: A, S type: S
1) Standard packing: 50 pcs.(tube), 500pcs. (tape and reel)in an inner package; 1,000 pcs. in an outer package
2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
Operating
Function
Part No. Coil Rating,
V DC Set voltage,
V DC (max.)
(initial)
Reset
voltage,
V DC (max.)
(initial)
Nominal
operating
current,
mA (
±
10%)
Coil
resistance,
Ω
(
±
10%)
Nominal
operating
power,
mW
Max.
allowable
voltage,
V DC
Tube packing Tape and reel
packing
1 coil
latching
AGN210
❍
1H AGN210
❍
1HZ 1.5 1.13 1.13 66.7 22.5 100 2.25
AGN210
❍
03 AGN210
❍
03Z 3 2.25 2.25 33.3 90 100 4.5
AGN210
❍
4H AGN210
❍
4HZ 4.5 3.38 3.38 22.2 202.5 100 6.75
AGN210
❍
06 AGN210
❍
06Z 6 4.5 4.5 16.7 360 100 9
AGN210
❍
09 AGN210
❍
09Z 9 6.75 6.75 11.1 810 100 13.5
AGN210
❍
12 AGN210
❍
12Z 12 9 9 8.3 1,440 100 18
AGN210
❍
24 AGN210
❍
24Z 24 18 18 5.0 4,800 120 36
DIMENSIONS
1. PC board terminal
10.60±0.3
.417±.012 5.70±0.3
.224±.012
0.40±0.1
.016±.004
(1.50)
(.059)
2.20±0.15
.087±.006
3.20±0.15
.126±.006
0.25±0.1
.010±.004
3.20±0.15
.126±.006
3.50±0.3
.138±.012
(0.50)
(.020)
9.00±0.3
.354±.012
PC board pattern
Tolerance:
±
0.1
±
.004
3.20
.126
2.20
.087
7.60
.299
3.20
.126
8-0.85 dia.
8-.033 dia
Schematic (Bottom view)
Single side stable
(Deenergized condition) 1 coil latching
(Reset condition)
Direction indication
8 765
1 234
Direction indication
4
5
2
78
1
6
3
mm inch
2. Surface-mount terminal
1) A type 10.60±0.3
.417±.012 5.70±0.3
.224±.012
0.40±0.1
.016±.004
(1.50)
(.059)
3.20±0.15
.126±.006
3.20±0.15
.126±.006
0.25±0.1
.010±.004
2.20±0.15
.087±.006 7.40±0.3
.291±.012
(0.50)
(.020)
9.00±0.3
.354±.012 Max. 10.00
.394
Suggested mounting pad
Tolerance: ±0.1 ±.004
2.20
.087
3.20
.126
5.30
.209
3.10
.122
0.80
.031
1) S type 10.60±0.3
.417±.012 5.70±0.3
.224±.012
3.20±0.15
.126±.006
0.40±0.1
.016±.004
(1.50)
(.059)
0.25±0.1
.010±.004
3.20±0.15
.126±.006
2.20±0.15
.087±.006 5.70±0.3
.224±.012
(0.50)
(.020)
9.00±0.3
.354±.012 Max. 10.00
.394
Suggested mounting pad
Tolerance: ±0.1 ±.004
2.20
.087
3.20
.126
4.45
.175
2.25
.089
0.80
.031
Schematic (Top view)
Single side stable
(Deenergized condition) 1 coil latcing
(Reset condition)
Direction indication
1 234
8 765
Direction indication
5678
2134
REFERENCE DATA
1. Max. switching capacity 2. Life curve
30 100
Contact voltage, V
1.0
0.3
DC resistive load
AC resistive load
Switching current, A
Switching current, A
No. of operations, × 104
0.2 0.4 0.6 0.8 1.0 1.2
100
50
30
40
20
10
0
DC 30V resistive load
AC 125V
resistive load
GN
128
NOTES
1. Coil operating power
1) As a general rule, only a pure DC pow-
er supply should be used f or the coil driv e.
2) T o ensure proper operation, the voltage
applied to both terminals of the coil should
be ±5% (at 20°C 68°F) the rated operating
voltage of the coil. Also, be a ware that the
pick-up and drop-out voltages will fluctu-
ate depending on the ambient tempera-
ture and operating conditions.
3) The ripple factor f or the voltage applied
to the coil should be less than 5%.
4) For set and reset latching relays, the
rated operating v oltage should be applied
to the coil for 10 ms or more.
2. Coil connection
When connecting coils, ref er to the wiring
diagram to prevent mis-operation or mal-
function.
3. External magnetic field
Since GN relays are highly sensitive po-
larized rela ys , their char acteristics will be
affected by a strong external magnetic
field. Avoid using the rela y under that con-
ditions.
4. Cleaning
In automatic cleaning, cleaning with the
boiling method is recommended. A v oid ul-
trasonic cleaning which subjects the rela y
to high frequency vibrations. It may cause
the contacts to stick.
lt is recommended that a fluorinated hy-
drocarbon or other alcoholic solvent be
used.
5. Packing style
1) The relay is packed in a tube with the
relay orientation mark on the left side, as
shown in the figure below.
2) Tape and reel packing
(A type)
(1)-1 Tape dimensions mm inch
(S type)
(1)-2 Tape dimensions
(2) Dimensions of plastic peel mm inch
6. Automatic insertion
To maintain the internal function of the
relay, the chucking pressure should not
exceed the values below.
Chucking pressure in the direction A:
4.9 N {500gf} or less
Chucking pressure in the direction B:
9.8 N {1 kgf} or less
Chucking pressure in the direction C:
9.8 N {1 kgf} or less
Please chuck the portion.
Avoid chucking the center of the relay.
In addition, excessive chucking pressure
to the pinpoint of the relay should be
avoided.
Orientation (indicates PIN No.1)stripe
Stopper (green) Stopper (red)
Relay polarity bar
(Z type)
Tape coming out direction
General tolerance ±0.1 mm .004 inch
4.00
.157 1.75
.069
0.40
.016
10.70±0.2
.421±.008
2.00
.079
2.00dia
.079dia
GN relays 16.00
.630 8.00
.315
11.50
.453
24.00±0.3
.945±.012
11.10
.437
1.50+0.1
0 dia
.059+.004
0 dia
Relay polarity bar
(Z type)
Tape coming out direction
General tolerance ±0.1 mm .004 inch
1.50+0.1
0 dia
.059+.004
0 dia
2.0dia
.079dia
4.00
.157 1.75
.069
10.70±0.2
.421±.008
0.40
.016
2.00
.079
GN relays 16.00
.630 6.3
.248
11.50
.453
11.10
.437
24.00±0.3
.945±.012
21±0.8 dia.
.827±.031 dia.
13±0.2 dia.
.512±.008 dia.
24.4
.961+2
0
+.079
0
100±1 dia.
3.937±.039 dia.
2.0±0.2
.079±.008
370±2 dia.
14.567±.079 dia.
2.0±0.5
.079±.020
ACB
,
,
,,
,
,
For Cautions for Use, see Relay Technical Information (Page 48 to 76).
9/1/2000 All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.
Go To Online Catalog
