Datasheet CMOS LDO Regulator Series for Portable Equipments Versatile Package FULL CMOS LDO Regulator BUxxTD2WNVX series General Description BUxxTD2WNVX series is high-performance FULL CMOS regulator with 200-mA output, which is mounted on versatile package SSON004X1010 (1.00mm x 1.00 mm x 0.60mm). It has excellent noise characteristics and load responsiveness characteristics despite its low circuit current consumption of 35A. It is most appropriate for various applications such as power supplies for logic IC, RF, and camera modules.ROHM's. Key Specifications Output voltage: Accuracy output voltage: Low current consumption: Operating temperature range: 1.0V to 3.4V 1.0% (25mV) 35A -40C to +85C Applications Battery-powered portable equipment, etc. Package SSON004X1010 : Features High accuracy detection low current consumption Compatible with small ceramic capacitor(Cin=Co=0.47uF) With built-in output discharge circuit High ripple rejection ON/OFF control of output voltage With built-in over current protection circuit and thermal shutdown circuit Low dropout voltage 1.00mm x 1.00mm x 0.60mm Typical Application Circuit STBY VIN STBY VOUT VOUT VIN GND GND GND Fig.1 Application Circuit Product structure:Silicon monolithic integrated circuit This product is not designed protection against radioactive rays. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211114001 1/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Connection Diagram BOTTOM VIEW SSON004X1010 (TOP VIEW) 4 VIN 3 STBY 1 VOUT 2 GND LOT Number reverse FIN 1 2 Part Number Marking 1 VOUT 2 GND 4 VIN 3 STBY 1PIN MARK Pin Descriptions SSON004X1010 Symbol Function VOUT Output Voltage GND Grouding ON/OFF control of output voltage STBY (High: ON, Low: OFF) VIN Power Supply Voltage FIN Substrate (Connect to GND) PIN No. 1 2 3 4 reverse Ordering Information B U x Part Number x T Output Voltage 10 : 1.0V D 2 W Low Dropout Voltage Maximum Output Current 200mA N V with Package output discharge NVX : SSON004X1010 X - T L Packageing and forming specification Embossed tape and reel TL : The pin number 1 is the lower left 34 : 3.4V SSON004X1010 <Tape and Reel information> 1.00.1 0.6MAX 1.00.1 1PIN MARK 0.320.1 1 2 5000pcs (0.12) +0.03 0.02 -0.02 05 0.650.05 0. 8 4 0. Embossed carrier tape Quantity Direction of feed S 0.05 Tape TL The direction is the 1pin of product is at the lower left when you hold ( reel on the left hand and you pull out the tape on the left hand ) 3-C0.18 R0.05 45 0.070.1 0.250.05 3 0.250.1 5 0 0. 48 0. 4 1pin (Unit : mm) Reel www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 2/40 Direction of feed Order quantity needs to be multiple of the minimum quantity. TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Lineup Marking Output Voltage Part Number A 1.0V BU10 6 1.05V BU1A 5 1.1V BU11 2 1.15V BU1B B 1.2V BU12 3 1.25V BU1C 5i 1.3V BU13 C 1.5V BU15 D 1.8V BU18 E 1.85V BU1J F 1.9V BU19 G 2.0V BU20 r 2.05V BU2A 0 2.1V BU21 1 2.3V BU23 H 2.5V BU25 J 2.6V BU26 K 2.7V BU27 a 2.75V BU2H L 2.8V BU28 M 2.85V BU2J N 2.9V BU29 P 3.0V BU30 Q 3.1V BU31 R 3.2V BU32 U 3.3V BU33 Y 3.4V BU34 Absolute Maximum Ratings (Ta=25C) PARAMETER Power Supply Voltage Power Dissipation Maximum junction temperature Operating Temperature Range Storage Temperature Range Symbol Limit Unit VMAX -0.3 +6.5 V 560(*1) mW +125 Topr -40 +85 Tstg -55 +125 Pd TjMAX (*1)Pd deleted at 5.6mW/ at temperatures above Ta=25, mounted on 70x70x1.6 mm glass-epoxy PCB. RECOMMENDED OPERATING RANGE (not to exceed Pd) PARAMETER Symbol Limit Unit Power Supply Voltage VIN 1.7~6.0 V Maximum Output Current IMAX 200 mA OPERATING CONDITIONS PARAMETER Symbol MIN. TYP. MAX. Unit Input Capacitor Cin 0.22(*2) 0.47 - F Output Capacitor Co 0.22(*2) 0.47 - F CONDITION Ceramic capacitor recommended (*2)Make sure that the output capacitor value is not kept lower than this specified level across a variety of temperature, DC bias, changing as time progresses characteristic. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 3/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Electrical Characteristics (Ta=25, VIN=VOUT+1.0V (*3), STBY=VIN, Cin=0.47F, Co=0.47F, unless otherwise noted.) PARAMETER Symbol Limit MIN. TYP. MAX. Unit Conditions Overall Device VOUTx0.99 Output Voltage VOUT VOUT-25mV Operating Current Operating Current (STBY) Ripple Rejection Ratio Dropout Voltage VOUT VOUTx1.01 V VOUT+25mV IOUT=10A, VOUT2.5V IOUT=10A, VOUT2.5V IIN - 35 60 A IOUT=0mA ISTBY - - 1.0 A STBY=0V RR 45 70 - dB VRR=-20dBv, fRR=1kHz, IOUT=10mA - 800 1100 mV 1.0VVOUT1.2V(IOUT=200mA) - 600 900 mV 1.2VVOUT1.5V(IOUT=200mA) - 440 700 mV 1.5VVOUT1.8V(IOUT=200mA) - 380 600 mV 1.8VVOUT2.5V(IOUT=200mA) - 280 540 mV 2.5VVOUT2.6V(IOUT=200mA) - 260 500 mV 2.7VVOUT2.85V(IOUT=200mA) - 240 460 mV 2.9VVOUT3.1V(IOUT=200mA) - 220 420 mV 3.2VVOUT3.4V(IOUT=200mA) VSAT Line Regulation VDL - 2 20 mV VIN=VOUT+1.0V to 5.5V (*4), IOUT=10A Load Regulation VDLO - 10 80 mV IOUT=0.01mA to 100mA Over Current Protection (OCP) Limit Current ILMAX 220 400 700 mA Vo=VOUT*0.95 Short Current ISHORT 20 70 150 mA Vo=0V VIN=4.0V, STBY=0V, VOUT=4.0V Standby Block Discharge Resistor RDSC 20 50 80 STBY Pin Pull-down Current ISTB 0.1 0.6 2.0 A ON VSTBH 1.2 - 6.0 V OFF VSTBL -0.3 - 0.3 V STBY Control Voltage STBY=1.5V This product is not designed for protection against radioactive rays. (*3) VIN=2.5V for VOUT1.5V (*4) VIN=2.5V to 3.6V for VOUT1.5V Block Diagrams VIN VIN 4 VREF VOUT Cin VOUT 1 GND 2 OCP Co TSD STBY STBY 3 STBY Discharge Cin0.47F (Ceramic) Co 0.47F (Ceramic) Fig. 2 Block Diagrams www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 4/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU12TD2WNVX (Ta=25C unless otherwise specified.) 1.4 100 1.25 Temp=25C 1.0 0.8 Io=0uA Io=100uA Io=50mA Io=200mA 0.6 0.4 0.2 VIN=STBY VIN=STBY 1.22 1.21 1.20 1.19 Io=0uA Io=100uA Io=50mA Io=200mA 1.18 1.17 1.16 0.0 Io=0uA 1.23 Gnd Current (uA) Output Voltage (V) Output Voltage (V) Temp=25C 1.24 1.2 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 Temp=85 Temp=25C Temp=-40C 60 40 20 VIN=STBY 0 1.15 0 80 1.1 1.2 1.3 1.4 Input Voltage (V) 1.5 1.6 1.7 1.8 1.9 0 2 0.5 1 1.5 Fig 3. Output Voltage 2 2.5 3 3.5 4 4.5 5 5.5 Input Voltage (V) Input Voltage (V) Fig 4. Line Regulation Fig 5. Circuit Current IGND 1.25 100 Temp=85C 1.0 0.8 0.6 0.4 Temp=25C 1.23 60 40 Temp=-40C Temp=25C 20 Temp=-40C Temp=85C Output Voltage (V) 1.2 80 0.2 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 1.20 1.19 1.18 1.17 Temp=-40C 0.05 0.1 0.15 0.2 0 1.24 VIN=2.5V Io=0mA 0.6 0.4 1.23 Output Voltage (V) Output Voltage (V) VIN=2.5V VIN=5.5V 1.0 Temp=25C 0.5 Temp=-40C Temp=85C 0.2 0.0 0.0 0.2 0.3 0.4 0.5 VIN=2.5V STBY=1.5V Io=0.1mA 1.22 1.21 1.20 1.19 1.18 1.17 1.16 STBY=1.5V 0.1 0.2 1.25 1.5 1.2 1.0 0.15 Fig 8. Load Regulation Fig 7. IOUT - IGND Temp=25C 0.1 Output Current (A) 1.4 VIN=1.7V 0.05 Output Current (A) Fig 6. VSTBY - ISTBY Output Voltage (V) Temp=85C 1.21 1.15 0 Input Voltage (V) 0 Temp=25C 1.22 1.16 0.0 0.8 VIN=2.5V STBY=1.5V 1.24 VIN=2.5V STBY=1.5V 1.4 Gnd Current (uA) STBY Pin Current (uA) 1.6 0 0.6 0.5 1 1.5 STBY Voltage (V) Output Current (A) -15 10 35 60 85 Temp (C) Fig 10. STBY Threshold Fig 9. OCP Threshold 1.15 -40 Fig 11. VOUT - Temp 60 1.0 VIN=2.5V STBY=1.5V Io=0mA 0.9 Gnd Current (uA) Gnd Current (uA) 50 40 30 20 VIN=2.5V STBY=0V 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 0.1 0 -40 0.0 -15 10 35 60 85 -40 Fig 12. IGND vs Temp -15 10 60 85 Fig 13. IGND - Temp (STBY) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 Temp (C) Temp (C) 5/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU12TD2WNVX (Ta=25C unless otherwise specified.) IOUT=0mA50mA 0 100 50 IOUT=50mA0mA 1.30 Output Voltage (V) Output Voltage (V) 1.25 1.20 1.15 1.10 1.25 1.20 1.15 Fig 15. Load Response Fig 14. Load Response 0 100 50 IOUT=100mA0mA 1.20 1.15 1.10 1.25 1.20 1.15 Fig 17. Load Response Fig 16. Load Response 0 200 100 IOUT=200mA0mA 0 1.40 Output Voltage (V) Output Voltage (V) 1.30 Output Current (mA) 100 Output Current (mA) 200 IOUT=0mA200mA 1.20 1.10 1.00 1.30 1.20 1.10 Fig 18. Load Response Fig 19. Load Response 0 100 IOUT=100mA50mA 50 0 1.25 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 1.25 Output Voltage (V) Output Voltage (V) 0 1.30 Output Voltage (V) Output Voltage (V) 1.25 Output Current (mA) 50 Output Current (mA) 100 IOUT=0mA100mA 1.20 1.15 1.10 Fig 20. Load Response 1.20 1.15 1.10 Fig 21. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 Output Current (mA) 50 Output Current (mA) 100 6/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU12TD2WNVX (Ta=25C unless otherwise specified.) 2.0 1.0 0.0 1.0 0.0 Fig 23. Start Up Time Iout=0mA Iout=200mA 2.0 VIN=STBY=02.5V 0.0 Output Voltage (V) 0.0 4.0 2.0 1.0 0.0 2.0 1.0 0.0 Fig 24. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA Fig 25. Start Up Time (VIN=STBY) Iout=200mA 3.5 2.5 2.0 1.21 Output Voltage (V) Output Voltage (V) 0.0 4.5 VIN=2.5V3.5V2.5V Input Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=1.50V STBY Voltage (V) 2.0 STBY Voltage (V) VIN=STBY=02.5V Output Voltage (V) 2.0 Fig 22. Start Up Time 4.0 1.0 0.0 1.20 1.19 1.18 Fig 27. VIN Response Fig 26. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1.0 0.0 Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY=01.5V STBY Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=01.5V 7/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU15TD2WNVX (Ta=25C unless otherwise specified.) 2.0 Temp=25C 1.54 1.4 1.2 1.0 0.8 Io=0uA Io=100uA Io=50mA Io=200mA 0.6 0.4 1.52 1.51 1.50 1.49 1.47 0.0 1.45 1 1.5 2 2.5 3 3.5 4 4.5 5 Io=0uA Io=100uA Io=50mA Io=200mA 1.48 1.46 0.5 5.5 1.4 Temp=-40C 1.5 1.6 1.7 1.8 1.9 2 0 2.1 Temp=85C 0.8 0.6 80 40 Temp=-40C Temp=25C 2 2.5 3 3.5 4 4.5 5 5.5 2.5 3 3.5 4 4.5 5 5.5 1.53 1.52 Temp=25C Temp=85C 1.51 1.50 1.49 1.48 1.47 Temp=-40C 1.46 1.45 0 1.5 2 VIN=2.5V STBY=1.5V 1.54 Temp=85C 60 20 Temp=-40C 0.0 1 1.5 1.55 VIN=2.5V STBY=1.5V 0.2 0.5 1 Fig 30. Circuit Current IGND Output Voltage (V) Gnd Current (uA) 1.2 0 0.5 Input Voltage (V) 100 1.4 Temp=25C Temp=25C 40 20 Fig 29. Line Regulation 1.6 0.4 Temp=85C 60 Input Voltage (V) Fig 28. Output Voltage 1.0 VIN=STBY 80 0 Input Voltage (V) STBY Pin Current (uA) IO=0uA 1.53 0.2 0 VIN=STBY Gnd Current (uA) 1.6 Output Voltage (V) Output Voltage (V) 100 1.55 Temp=25C 1.8 0 0.05 Input Voltage (V) 0.1 0.15 0 0.2 0.05 0.15 0.2 Fig 33. Load Regulation Fig 32. IOUT - IGND Fig 31. VSTBY - ISTBY 0.1 Output Current (A) Output Current (A) 1.55 2.0 2.0 Temp=25C 1.6 Output Voltage (V) Output Voltage (V) VIN=2.5V 1.4 VIN=2.0V VIN=5.5V 1.2 1.0 0.8 0.6 0.4 0.2 1.5 1.0 Temp=25C 0.0 0 0.1 0.2 0.3 0.4 0.5 1.53 1.52 1.51 1.50 1.49 1.48 1.47 1.46 STBY=1.5V 0.0 0.6 1.45 0 0.5 Output Current (A) 1 1.5 -40 -15 10 35 60 85 Temp (C) STBY Voltage (V) Fig 34. OCP Threshold Fig 36. VOUT - Temp Fig 35. STBY Threshold 1.0 60 VIN=2.5V STBY=1.5V Io=0mA 0.9 Gnd Current (uA) 50 Gnd Current (uA) Temp=-40C Temp=85C 0.5 VIN=2.5V STBY=1.5V Io=0.1mA 1.54 VIN=3.8V Io=0mA Output Voltage (V) 1.8 40 30 20 VIN=2.5V STBY=0V 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 0.1 0.0 0 -40 -15 10 35 60 85 -40 Fig 37. IGND vs Temp -15 10 60 85 Fig 38. IGND vs Temp (STBY) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 Temp (C) Temp (C) 8/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU15TD2WNVX (Ta=25C unless otherwise specified.) IOUT=0mA50mA 0 100 50 IOUT=50mA0mA Output Voltage (V) Output Voltage (V) 1.55 1.50 1.45 1.40 1.60 1.30 1.55 1.25 1.50 1.20 1.45 1.15 Fig 40. Load Response Fig 39. Load Response 0 100 50 IOUT=100mA0mA Output Output Voltage Voltage (V) (V) Output Voltage (V) 1.55 1.50 1.45 1.40 1.30 1.60 1.25 1.55 1.20 1.50 1.15 1.45 Fig 42. Load Response Fig 41. Load Response 0 200 100 IOUT=200mA0mA 1.40 1.70 Output Output Voltage Voltage (V) (V) 1.60 Output Voltage (V) 0 Output Current Current (mA) (mA) Output 100 Output Current (mA) 200 IOUT=0mA200mA 1.50 1.40 1.30 1.30 1.60 1.20 1.50 1.10 1.40 Fig 44. Load Response Fig 43. Load Response 0 100 IOUT=100mA50mA 50 0 1.55 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 1.60 Output Voltage (V) Output Voltage (V) 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=0mA100mA 1.50 1.45 1.40 Fig 45. Load Response 1.55 1.50 1.45 Fig 46. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 Output Current (mA) 50 Output Current (mA) 100 9/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU15TD2WNVX (Ta=25C unless otherwise specified.) 2.0 1.0 0.0 1.0 0.0 Fig 48. Start Up Time Iout=0mA Iout=200mA 4.0 2.0 VIN=STBY=02.5V Output Voltage (V) 0.0 2.0 1.0 0.0 2.0 1.0 0.0 Fig 50. Start Up Time (VIN=STBY) Iout=200mA Fig 49. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA 3.5 2.5 1.51 2.0 Output Voltage (V) Output Voltage (V) 0.0 4.5 VIN=2.5V3.5V2.5V Input Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=1.50V STBY Voltage (V) 0.0 STBY Voltage (V) 2.0 VIN=STBY=02.5V Output Voltage (V) 2.0 Fig 47. Start Up Time 4.0 1.0 0.0 1.50 1.49 1.48 Fig 52. VIN Response Fig 51. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1.0 0.0 Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY=01.5V STBY Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=01.5V 10/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU18TD2WNVX (Ta=25C unless otherwise specified.) 2.0 1.85 Temp=25C 1.84 1.4 1.2 1.0 Io=0uA Io=100uA Io=50mA Io=200mA 0.8 0.6 0.4 VIN=STBY 0.2 VIN=STBY 1.82 1.81 1.80 1.79 Io=0uA Io=100uA Io=50mA Io=200mA 1.78 1.77 1.76 0.0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 1.7 Temp=-40C 1.8 1.9 2 2.1 2.2 2.3 2.4 0 2.5 0.5 1 1.5 0.8 0.6 80 3.5 4 4.5 5 5.5 VIN=2.8V STBY=1.5V 1.84 Temp=85C 60 40 Temp=-40C Temp=25C 20 Temp=-40C 3 1.85 VIN=2.8V STBY=1.5V Output Voltage (V) Gnd Current (uA) Temp=85C 2.5 Fig 55. Circuit Current IGND 100 1.4 1.2 2 Input Voltage (V) Fig 54. Line Regulation 1.6 Temp=25C Temp=25C 40 Input Voltage (V) Fig 53. Output Voltage 0.4 Temp=85C 60 0 Input Voltage (V) 1.0 VIN=STBY 80 20 1.75 0 STBY Pin Current (uA) Io=0uA 1.83 Gnd Current (uA) 1.6 Output Voltage (V) Output Voltage (V) 100 Temp=25C 1.8 0.2 1.83 Temp=25C 1.82 Temp=85C 1.81 1.80 1.79 1.78 1.77 Temp=-40C 1.76 0 0.0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 1.75 0 5.5 0.05 0.1 0.15 0.2 0 0.05 0.15 0.2 Fig 58. Load Regulation Fig 57. IOUT - IGND Fig 56. VSTBY - ISTBY 0.1 Output Current (A) Output Current (A) Input Voltage (V) 1.85 2.0 2.0 VIN=2.8V STBY=1.5V Io=0.1mA 1.84 1.6 Output Voltage (V) Output Voltage (V) VIN=2.8V VIN=5.5V 1.4 VIN=2.3V 1.2 1.0 0.8 0.6 0.4 Temp=25C 0.2 STBY=1.5V 1.5 1.0 Temp=25C Temp=-40C Temp=85C 0.5 0.0 0.1 0.2 0.3 0.4 0.5 1.83 1.82 1.81 1.80 1.79 1.78 1.77 1.76 0.0 0.0 1.75 0 0.6 0.5 1 1.5 60 -15 10 35 60 85 Fig 61. VOUT - Temp Fig 60. STBY Threshold Fig 59. OCP Threshold -40 Temp (C) STBY Voltage (V) Output Current (mA) 1.0 VIN=2.8V STBY=1.5V Io=0mA 0.9 Gnd Current (uA) 50 Gnd Current (uA) Output Voltage (V) VIN=3.8V Io=0mA 1.8 40 30 20 VIN=2.8V STBY=0V 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 0.1 0 0.0 -40 -15 10 35 60 85 -40 Temp (C) Fig 62. IGND - Temp -15 10 60 85 Fig 63. IGND - Temp (STBY) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 Temp (C) 11/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU18TD2WNVX (Ta=25C unless otherwise specified.) 0 100 50 IOUT=50mA0mA 1.90 Output Voltage (V) Output Voltage (V) 1.85 1.80 1.75 1.85 1.80 1.75 1.70 Fig 65. Load Response Fig 64. Load Response 50 0 100 50 IOUT=100mA0mA 1.90 Output Voltage (V) Output Voltage (V) 1.85 1.80 1.75 1.70 1.85 1.80 1.75 Fig 67. Load Response Fig 66. Load Response 0 200 100 IOUT=200mA0mA 2.00 Output Voltage (V) 1.90 Output Voltage (V) 0 Output Current (mA) 100 Output Current (mA) 200 IOUT=0mA200mA 1.80 1.70 1.60 1.90 1.80 1.70 Fig 69. Load Response Fig 68. Load Response 50 0 100 IOUT=100mA50mA 50 0 1.90 Output Current (mA) 100 Output Current (mA) IOUT=50mA100mA 1.85 Output Voltage (V) Output Voltage (V) 0 Output Current (mA) 100 Output Current (mA) IOUT=0mA100mA 1.80 1.70 1.60 1.80 1.75 1.70 Fig 71. Load Response Fig 70. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 Output Current (mA) 50 IOUT=0mA50mA Output Current (mA) 100 12/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU18TD2WNVX (Ta=25C unless otherwise specified.) 2.0 1.0 0.0 1.0 0.0 Fig 73. Start Up Time Iout=0mA Iout=200mA 2.0 VIN=STBY=2.80V 2.0 1.0 0.0 2.0 1.0 0.0 Fig 74. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA Fig 75. Start Up Time (VIN=STBY) Iout=200mA 3.8 2.8 1.81 2.0 Output Voltage (V) Output Voltage (V) 0.0 4.8 VIN=2.8V3.8V2.8V Input Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=1.50V 2.0 0.0 Output Voltage (V) 0.0 4.0 STBY Voltage (V) STBY Voltage (V) VIN=STBY=02.8V Output Voltage (V) 2.0 Fig 72. Start Up Time 4.0 1.0 0.0 1.80 1.79 1.78 Fig 77. VIN Response Fig 76. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1.0 0.0 Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY=01.5V STBY Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=01.5V 13/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series BU19TD2WNVX Reference data (Ta=25C unless otherwise specified.) 1.95 2.0 Temp=25C 100 Temp=25C 1.94 IO=0uA 1.93 Io=0uA Io=100uA Io=50mA Io=200mA 1.4 1.2 1.0 0.8 0.6 0.4 1.92 1.91 1.90 1.89 Io=0uA Io=100uA Io=50mA Io=200mA 1.88 1.87 0.2 1.86 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 1.9 2 20 Temp=-40C 2.1 Input Voltage (V) 2.3 2.4 0 2.5 1.5 Temp=85C 0.8 0.6 2.5 3 3.5 4 4.5 5 5.5 1.95 VIN=3.9V STBY=1.5V 80 VIN=2.9V STBY=1.5V 1.94 Temp=85C 1.93 60 40 Temp=-40C Temp=25C 20 Temp=-40C 2 Fig 80. Circuit Current IGND Output Voltage (V) Gnd Current (uA) 1.2 Temp=25C 1 Input Voltage (V) 100 1.4 0.4 0.5 Fig 79. Line Regulation 1.6 STBY Pin Current (uA) 2.2 Input Voltage (V) Fig 78. Output Voltage 1.0 Temp=25C 40 0 1.85 1.8 5.5 Temp=85C 60 VIN=STBY 0.0 0 VIN=STBY 80 Gnd Current (uA) 1.6 Output Voltage (V) Output Voltage (V) 1.8 0.2 1.92 Temp=25C 1.91 1.90 1.89 1.88 Temp=-40C 1.87 Temp=85C 1.86 0 0.0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0 5.5 0.05 0.1 0.15 1.85 0.2 0 Output Current (A) Input Voltage (V) 0.1 0.15 0.2 Output Current (A) Fig 82. IOUT - IGND Fig 81. VSTBY - ISTBY 0.05 Fig 83. Load Regulation 1.95 2.0 2.0 VIN=2.4V 1.4 1.2 1.0 0.8 0.6 0.4 Temp=25C 0.2 STBY=1.5V 1.5 1.0 Temp=25C 0.2 0.3 0.4 0.5 0.5 0.6 1 1.5 STBY Voltage (V) Fig 84. OCP Threshold 1.89 1.88 1.85 -40 -15 10 35 60 85 Fig 86. VOUT - Temp Fig 85. STBY Threshold 60 1.0 VIN=2.9V STBY=1.5V Io=0A 0.9 Gnd Current (uA) Gnd Current (uA) 1.90 Temp (C) Output Current (A) 50 1.91 1.86 0 0.1 1.92 1.87 0.0 0.0 0 Temp=-40C Temp=85C 0.5 VIN=2.9V STBY=1.5V Io=100A 1.93 Output Voltage (V) 1.6 Output Voltage (V) Output Voltage (V) VIN=2.9V VIN=5.5V 1.94 VIN=3.9V Io=0mA 1.8 40 30 20 VIN=2.9V STBY=0V 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 0.1 0.0 0 -40 -40 -15 10 35 60 85 10 60 85 Fig 88. IGND - Temp (STBY) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 Temp (C) Temp (C) Fig 87. IGND - Temp -15 14/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU19TD2WNVX (Ta=25C unless otherwise specified.) IOUT=0mA50mA 0 100 50 IOUT=50mA0mA 0 2.00 Output Voltage (V) Output Voltage (V) 1.95 1.90 1.85 1.80 1.95 1.90 1.85 Fig 89. Load Response Fig 90. Load Response 0 100 50 IOUT=100mA0mA 2.00 Output Voltage (V) Output Voltage (V) 1.95 1.90 1.85 1.80 1.95 1.90 1.85 Fig 91. Load Response Fig 92. Load Response 0 200 100 IOUT=200mA0mA 2.10 Output Voltage (V) Output Voltage (V) 2.00 0 Output Current (mA) 100 Output Current (mA) 200 IOUT=0mA200mA 1.90 1.80 1.70 2.00 1.90 1.80 Fig 93. Load Response Fig 94. Load Response 0 100 IOUT=100mA50mA 50 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 2.00 Output Voltage (V) 1.95 Output Voltage (V) 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=0mA100mA 1.90 1.85 1.80 1.95 1.90 1.85 Fig 96. Load Response Fig 95. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Output Current (mA) 50 Output Current (mA) 100 15/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU19TD2WNVX (Ta=25C unless otherwise specified.) 2.0 1.0 0.0 1.0 0.0 Fig 98. Start Up Time Iout=0mA Iout=200mA 2.0 1.0 0.0 2.0 1.0 0.0 Fig 99. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA Fig 100. Start Up Time (VIN=STBY) Iout=200mA 3.9 2.9 1.91 2.0 Output Voltage (V) Output Voltage (V) 0.0 4.9 VIN=2.9V3.9V2.9V Input Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=1.50V 2.0 0.0 Output Voltage (V) 0.0 4.0 VIN=STBY=02.9V STBY Voltage (V) 2.0 STBY Voltage (V) VIN=STBY=02.9V Output Voltage (V) 2.0 Fig 97. Start Up Time 4.0 1.0 0.0 1.90 1.89 1.88 Fig 102. VIN Response Fig 101. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1.0 0.0 Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY=01.5V STBY Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=01.5V 16/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU25TD2WNVX (Ta=25C unless otherwise specified.) 3.5 100 2.55 Temp=25C 2.54 IO=0uA Output Voltage (V) 2.0 Io=0uA Io=100uA Io=50mA Io=200mA 1.5 1.0 2.52 2.51 2.50 2.49 2.48 20 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 2.4 2.5 2.6 Input Voltage (V) 2.8 2.9 3 0 3.1 Temp=85C 0.8 0.6 Temp=25C 1.5 80 2.5 3 3.5 4 4.5 5 5.5 VIN=3.5V STBY=1.5V 2.54 Temp=85C 60 40 Temp=-40C Temp=25C 20 Temp=-40C 2 2.55 VIN=3.5V STBY=1.5V 2.53 Output Voltage (V) Gnd Current (uA) 1.2 0.4 1 Fig 105. Circuit Current IGND 100 1.4 1.0 0.5 Input Voltage (V) Fig 104. Line Regulation 1.6 2.52 Temp=25C 2.51 2.50 2.49 2.48 Temp=-40C 2.47 0.2 Temp=85C 2.46 0 0.0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 2.45 0 5.5 0.05 0.1 0.15 0.35 3.0 0.30 2.5 Output Voltage (V) Temp=85C 0.25 Temp=25C Temp=-40C 0.10 0.05 0.1 0.15 2.5 VIN=5.5V 2.0 VIN=3.0V 1.5 1.0 1.5 Temp=25C 1.0 Temp=-40C Temp=85C STBY=1.5V 0.0 0 0.2 0.1 0.2 0.3 0.4 0.5 0.6 0 0.5 Output Current (A) 2.55 1.0 VIN=3.5V STBY=1.5V Io=0mA Gnd Current (uA) 50 2.52 2.51 2.50 2.49 2.48 2.47 1.5 Fig 111. STBY Threshold 60 VIN=3.5V STBY=1.5V Io=0.1mA 1 STBY Voltage (V) Fig 110. OCP Threshold Fig 109. Dropout Voltage 2.53 2.0 0.5 Output Current (A) 2.54 0.2 VIN=3.5V Io=0mA VIN=3.5V 0.0 0.00 0 0.15 Fig 108. Load Regulation 0.5 VIN = 0.98 x VOUT STBY=1.5V 0.1 3.0 Temp=25C 0.05 0.05 Output Current (A) Fig 107. IOUT - IGND Fig 106. VSTBY - ISTBY 0.15 0 Output Current (A) Input Voltage (V) 0.20 0.2 0.9 Gnd Current (uA) STBY Pin Current (uA) 2.7 Input Voltage (V) Fig 103. Output Voltage Dropout Voltage (V) Temp=-40C 0 2.45 0 Output Voltage (V) Temp=25C 40 VIN=STBY 2.46 0.0 Temp=85C 60 2.47 0.5 VIN=STBY VIN=STBY 80 Output Voltage (V) Output Voltage (V) 2.5 Io=0uA Io=100uA Io=50mA Io=200mA 2.53 Gnd Current (uA) Temp=25C 3.0 40 30 20 VIN=3.5V STBY=0V 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 2.46 0.1 2.45 0 -40 -15 10 35 60 85 0.0 -40 Temp (C) Fig 112. VOUT - Temp -15 10 Temp (C) Fig 113. IGND - Temp www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 17/40 60 85 -40 -15 10 35 60 85 Temp (C) Fig 114. IGND - Temp (STBY) TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU25TD2WNVX (Ta=25C unless otherwise specified.) 0 100 50 IOUT=50mA0mA 2.60 Output Voltage (V) Output Voltage (V) 2.55 2.50 2.45 2.40 2.55 2.50 2.45 Fig 115. Load Response Fig 116. Load Response 0 200 100 IOUT=100mA0mA 2.60 Output Voltage (V) Output Voltage (V) 2.55 2.50 2.45 2.40 2.55 2.50 2.45 Fig 117. Load Response Fig 118. Load Response 0 200 100 IOUT=200mA0mA 0 2.70 Output Voltage (V) Output Voltage (V) 2.60 Output Current (mA) 100 Output Current (mA) 200 IOUT=0mA200mA 2.50 2.40 2.30 2.60 2.50 2.40 Fig 119. Load Response Fig 120. Load Response 0 100 IOUT=100mA50mA 50 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 2.60 Output Voltage (V) 2.55 Output Voltage (V) 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=0mA100mA 2.50 2.45 2.40 2.55 2.50 2.45 Fig 122. Load Response Fig 121. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 Output Current (mA) 50 IOUT=0mA50mA Output Current (mA) 100 18/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU25TD2WNVX (Ta=25C unless otherwise specified.) 1.0 4.0 0.0 4.0 2.0 0.0 Fig 123. Start Up Time Fig 124. Start Up Time Iout=0mA Iout=200mA 2.0 0.0 Output Voltage (V) 0.0 4.0 VIN=STBY=03.5V 4.0 2.0 0.0 4.0 2.0 0.0 Fig 126. Start Up Time (VIN=STBY) Iout=200mA Fig 125. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA 4.5 3.5 2.51 4.0 Output Voltage (V) Output Voltage (V) 0 5.5 VIN=3.5V4.5V3.5V Input Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=1.50V STBY Voltage (V) 2.0 STBY Voltage (V) 4.0 2.0 0.0 2.50 2.49 2.48 Fig 128. VIN Response Fig 127. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1.0 0.0 2.0 VIN=STBY=03.5V Output Voltage (V) STBY=01.5V Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY Voltage (V) STBY=01.5V STBY Voltage (V) 2.0 19/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU26TD2WNVX (Ta=25C unless otherwise specified.) 2.65 Temp=25C Output Voltage (V) 2.5 2.0 1.5 Io=0uA Io=100uA Io=50mA Io=200mA 1.0 0.5 2.63 0.0 2.62 2.61 2.60 2.59 Io=0uA Io=100uA Io=50mA Io=200mA 2.58 2.57 Temp=25C 40 20 Temp=-40C 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0 2.5 5.5 2.6 2.7 Input Voltage (V) 2.8 2.9 3 3.1 0 3.2 Gnd Current (uA) 1.2 Temp=85C 0.8 0.6 Temp=25C 3 3.5 40 Temp=-40C Temp=25C 2.62 1.5 2 2.5 3 3.5 4.5 5 2.59 2.58 2.57 Temp=85C 2.55 0 5.5 0.05 0.1 0.15 0.2 0 3.0 0.30 2.5 Temp=25C 0.15 Temp=-40C 0.10 VIN = 0.98 x VOUT STBY=1.5V 0.05 VIN=5.5V VIN=3.6V 2.0 1.5 1.0 0.15 Temp=-40C Temp=85C 0.1 0.2 0.3 0.4 0.5 0.6 0 0.5 Output Current (A) Fig 135. Dropout Voltage 1.0 VIN=3.6V STBY=1.5V Io=0mA Gnd Current (uA) 50 2.62 2.61 2.60 2.59 2.58 2.57 1.5 Fig 137. STBY Threshold 60 VIN=3.6V STBY=1.5V Io=0.1mA 1 STBY Voltage (V) Fig 136. OCP Threshold 2.65 2.63 Temp=25C 1.0 0.0 0 Output Current (A) 2.64 1.5 STBY=1.5V 0.2 0.9 Gnd Current (uA) 0.1 2.0 0.5 0.0 0.05 VIN=3.6V Io=0mA 2.5 0.5 0.00 0 0.2 3.0 VIN=3.1V Output Voltage (V) Output Voltage (V) 0.25 0.15 Fig 134. Load Regulation Temp=25C Temp=85C 0.1 Output Current (A) Fig 133. IOUT - IGND Fig 132. VSTBY - ISTBY 0.20 0.05 Output Current (A) Input Voltage (V) 0.35 5.5 Temp=25C Temp=-40C 4 5 2.60 0 1 4.5 2.61 2.56 0.5 4 2.63 0.2 0 Dropout Voltage (V) 2.5 VIN=3.6V STBY=1.5V 2.64 Temp=85C 60 20 Temp=-40C 2 2.65 VIN=3.6V STBY=1.5V 80 0.0 Output Voltage (V) 1.5 Fig 131. Circuit Current IGND 100 1.4 0.4 1 Input Voltage (V) Fig 130. Line Regulation 1.6 1.0 0.5 Input Voltage (V) Fig 129. Output Voltage STBY Pin Current (uA) Temp=85C 60 2.55 0 VIN=STBY 80 2.56 VIN=STBY IO=0uA VIN=STBY Output Voltage (V) Output Voltage (V) 100 Temp=25C 2.64 Gnd Current (uA) 3.0 40 30 20 VIN=3.6V STBY=0V 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 2.56 0.1 2.55 0 -40 -15 10 35 60 85 0.0 -40 Temp (C) Fig 138. VOUT - Temp -15 10 60 Temp (C) Fig 139. IGND - Temp www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 20/40 85 -40 -15 10 35 60 85 Temp (C) Fig 140. IGND - Temp (STBY) TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU26TD2WNVX (Ta=25C unless otherwise specified.) 0 100 50 IOUT=50mA0mA 0 2.70 Output Voltage (V) Output Voltage (V) 2.65 2.60 2.55 2.50 2.65 2.60 2.55 Fig 141. Load Response Fig 142. Load Response 0 100 IOUT=100mA0mA 50 0 2.70 Output Voltage (V) Output Voltage (V) 2.65 2.60 2.55 2.50 2.65 2.60 2.55 Fig 143. Load Response Fig 144. Load Response 0 200 100 IOUT=200mA0mA 0 2.80 Output Voltage (V) 2.70 Output Voltage (V) Output Current (mA) 100 Output Current (mA) 200 IOUT=0mA200mA 2.60 2.50 2.40 2.70 2.60 2.50 Fig 145. Load Response Fig 146. Load Response 0 100 IOUT=100mA50mA 50 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 2.62 Output Voltage (V) 2.65 Output Voltage (V) Output Current (mA) 50 Output Current (mA) 100 IOUT=0mA100mA 2.60 2.55 2.50 2.61 2.60 2.59 Fig 148. Load Response Fig 147. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Output Current (mA) 50 IOUT=0mA50mA Output Current (mA) 100 21/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU26TD2WNVX (Ta=25C unless otherwise specified.) 1.0 4.0 0.0 4.0 2.0 0.0 Fig 149. Start Up Time Fig 150. Start Up Time Iout=0mA Iout=200mA 2.0 0.0 Output Voltage (V) 0.0 4.0 VIN=STBY=03.6V 4.0 2.0 0.0 4.0 2.0 0.0 Fig 152. Start Up Time (VIN=STBY) Iout=200mA Fig 151. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA 4.6 3.6 Output Voltage (V) Output Voltage (V) 0.0 5.6 VIN=3.6V4.6V3.6V 4.0 2.0 0.0 Input Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=1.50V STBY Voltage (V) 2.0 STBY Voltage (V) 4.0 2.65 2.60 2.55 Fig 154. VIN Response Fig 153. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1.0 0.0 2.0 VIN=STBY=03.6V Output Voltage (V) STBY=01.5V Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY Voltage (V) STBY=01.5V STBY Voltage (V) 2.0 22/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series BU27TD2WNVX Reference data (Ta=25C unless otherwise specified.) Temp=25C 2.74 Output Voltage (V) 2.5 2.0 1.5 Io=0uA Io=100uA Io=50mA Io=200mA 1.0 0.5 0.0 2.72 2.71 2.70 2.69 Io=0uA Io=100uA Io=50mA Io=200mA 2.68 2.67 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 2.7 2.8 3 3.1 3.2 3.3 0 1.2 Temp=85C 0.8 0.6 Temp=25C 0.5 1 1.5 2.5 3 3.5 4 4.5 5 5.5 Fig 157. Circuit Current IGND 2.75 VIN=3.7V STBY=1.5V 80 VIN=3.7V STBY=1.5V 2.74 Temp=85C 60 40 Temp=-40C Temp=25C 20 Temp=-40C 2 Input Voltage (V) 2.73 Output Voltage (V) Gnd Current (uA) 2.72 Temp=25C 2.71 2.70 2.69 2.68 2.67 0.2 Temp=85C Temp=-40C 2.66 0 0.0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 2.65 0 5.5 0.05 0.1 0.15 0.2 0 0.35 3.0 0.30 2.5 Temp=25C 0.20 Temp=-40C 0.10 VIN=3.7V Io=0mA 2.5 VIN=5.5V VIN=3.6V 2.0 1.5 1.0 Temp=25C 0.5 VIN = 0.98 x VOUT STBY=1.5V 0.05 0.05 0.1 0.15 Temp=25C 1.0 Temp=-40C Temp=85C 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0 0.5 Output Current (A) 2.75 1.0 VIN=3.7V STBY=1.5V Io=0.1mA Gnd Current (uA) 50 2.72 2.71 2.70 2.69 2.68 2.67 1.5 Fig 163. STBY Threshold 60 VIN=3.7V STBY=1.5V Io=0.1mA 1 STBY Voltage (V) Fig 162. OCP Threshold Fig 161. Dropout Voltage 2.73 1.5 STBY=1.5V 0 0.2 Output Current (A) 2.74 2.0 0.5 0.0 0.00 0 0.2 3.0 Output Voltage (V) Output Voltage (V) 0.25 0.15 Fig 160. Load Regulation VIN=3.1V Temp=85C 0.1 Output Current (A) Fig 159. IOUT - IGND Fig 158. VSTBY - ISTBY 0.15 0.05 Output Current (A) Input Voltage (V) 0.9 Gnd Current (uA) STBY Pin Current (uA) 2.9 100 1.4 0.4 Temp=-40C 20 Fig 156. Line Regulation 1.6 Dropout Voltage (V) Temp=25C 40 Input Voltage (V) Fig 155. Output Voltage 1.0 Temp=85C 0 2.6 5.5 Input Voltage (V) Output Voltage (V) 60 2.65 0 VIN=STBY 80 2.73 2.66 VIN=STBY IO=0uA VIN=STBY Gnd Current (uA) Temp=25C Output Voltage (V) 100 2.75 3.0 40 30 20 VIN=3.7V STBY=0V 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 2.66 0.1 2.65 0 -40 -15 10 35 60 85 0.0 -40 Temp (C) Fig 164. VOUT - Temp -15 10 60 Temp (C) Fig 165. IGND - Temp www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 23/40 85 -40 -15 10 35 60 85 Temp (C) Fig 166. IGND - Temp (STBY) TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU27TD2WNVX (Ta=25C unless otherwise specified.) 0 100 50 IOUT=50mA0mA 2.80 Output Voltage (V) Output Voltage (V) 2.75 2.70 2.65 2.60 2.75 2.70 2.65 Fig 167. Load Response Fig 168. Load Response 0 100 50 IOUT=100mA0mA 0 2.80 Output Voltage (V) Output Voltage (V) 2.75 2.70 2.65 2.60 2.75 2.70 2.65 Fig 170. Load Response Fig 169. Load Response 0 200 100 IOUT=200mA0mA 0 2.90 Output Voltage (V) Output Voltage (V) 2.80 Output Current (mA) 100 Output Current (mA) 200 IOUT=0mA200mA 2.70 2.60 2.50 2.80 2.70 2.60 Fig 171. Load Response Fig 172. Load Response 0 100 IOUT=100mA50mA 50 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 2.80 Output Voltage (V) 2.75 Output Voltage (V) Output Current (mA) 50 Output Current (mA) 100 IOUT=0mA100mA 2.70 2.65 2.60 2.75 2.70 2.65 Fig 174. Load Response Fig 173. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 Output Current (mA) 50 IOUT=0mA50mA Output Current (mA) 100 24/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU27TD2WNVX (Ta=25C unless otherwise specified.) 1.0 0.0 4.0 2.0 0.0 4.0 2.0 0.0 Fig 175. Start Up Time Fig 176. Start Up Time Iout=0mA Iout=200mA 2.0 0.0 Output Voltage (V) 0.0 4.0 VIN=STBY=03.7V 4.0 2.0 0.0 4.0 2.0 0.0 Fig 177. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA Fig 178. Start Up Time (VIN=STBY) Iout=200mA 4.7 3.7 2.71 4.0 Output Voltage (V) Output Voltage (V) 0.0 5.7 Input Voltage (V) 1.0 STBY=1.50V STBY Voltage (V) 2.0 2.0 0.0 2.70 2.69 2.68 Fig 180. VIN Response Fig 179. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 STBY Voltage (V) 2.0 STBY Voltage (V) 4.0 VIN=STBY=03.7V Output Voltage (V) 1.0 STBY=01.5V Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY Voltage (V) STBY=01.5V STBY Voltage (V) 2.0 25/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series BU28TD2WNVX Reference data (Ta=25C unless otherwise specified.) 2.85 Temp=25C Output Voltage (V) 2.5 2.0 1.5 Io=0uA Io=100uA Io=50mA Io=200mA 1.0 0.5 VIN=STBY 2.83 2.82 2.81 2.80 2.79 2.78 2.77 Temp=-40C 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 0 2.7 2.8 2.9 3 3.1 3.2 3.3 3.4 0 Temp=85C 0.8 0.6 80 40 Temp=-40C Temp=25C 2.82 1 1.5 2 2.5 3 3.5 4 4.5 5 0.05 Input Voltage (V) Fig 184. VSTBY - ISTBY 3.0 2.5 2.78 2.77 0.1 0.15 0 0.2 0.20 Temp=25C 0.15 Temp=-40C 0.10 VIN = 0.98 x VOUT STBY=1.5V 0.05 0.1 0.15 VIN=3.8V 2.0 1.5 1.0 Temp=25C 0.5 0.1 Temp=25C 1.0 0.2 0.3 0.4 0.5 0.6 0 0.5 Gnd Current (uA) 2.81 2.80 2.79 2.78 2.77 1.5 Fig 189. STBY Threshold 1.0 VIN=3.8V STBY=1.5V Io=0mA 50 2.82 1 STBY Voltage (V) 60 VIN=3.8V STBY=1.5V Io=0.1mA Temp=-40C Temp=85C 0.5 Fig 188. OCP Threshold Fig 187. Dropout Voltage 2.83 1.5 Output Current (A) Output Current (A) 2.84 2.0 0.0 0 2.85 0.2 VIN=3.8V Io=0mA 2.5 VIN=5.5V 0.2 0.15 3.0 0.0 0.05 0.1 Fig 186. Load Regulation STBY=1.5V 0.00 0 0.05 Output Current (A) Output Voltage (V) Output Voltage (V) 0.25 Temp=85C Temp=-40C VIN=3.3V Temp=85C 5.5 2.79 Fig 185. IOUT - IGND 0.30 5 2.80 Output Current (A) 0.35 4.5 2.75 0 5.5 4 Temp=25C 2.76 0.5 3.5 2.81 0 0 3 2.83 0.2 0.0 2.5 VIN=3.8V STBY=1.5V 2.84 Temp=85C 60 20 Temp=-40C 2 2.85 VIN=3.8V STBY=1.5V Output Voltage (V) Gnd Current (uA) 1.2 Temp=25C 1.5 Fig 183. Circuit Current IGND 100 1.4 0.4 1 Input Voltage (V) Fig 182. Line Regulation 1.6 1.0 0.5 Input Voltage (V) Fig 181. Output Voltage STBY Pin Current (uA) Temp=25C 40 20 Input Voltage (V) Dropout Voltage (V) Temp=85C 60 2.75 0 VIN=STBY Io=0uA 80 2.76 0.0 Output Voltage (V) VIN=STBY Io=0uA Io=100uA Io=50mA Io=200mA VIN=3.8V STBY=0V 0.9 Gnd Current (uA) Output Voltage (V) 100 Temp=25C 2.84 Gnd Current (uA) 3.0 40 30 20 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 2.76 0.1 2.75 0 -40 -15 10 35 60 85 0.0 -40 Temp (C) Fig 190. VOUT - Temp -15 10 60 Temp (C) Fig 191. IGND - Temp www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 26/40 85 -40 -15 10 35 60 85 Temp (C) Fig 192. IGND - Temp (STBY) TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU28TD2WNVX (Ta=25C unless otherwise specified.) 50 IOUT=0mA50mA 0 Output Current (mA) 100 Output Voltage (V) 2.85 2.80 2.75 2.70 Fig 193. Load Response Fig 194. Load Response 0 100 50 IOUT=100mA0mA 0 2.90 Output Voltage (V) Output Voltage (V) 2.85 2.80 2.75 2.70 2.85 2.80 2.75 Fig 195. Load Response Fig 196. Load Response 0 200 100 IOUT=200mA0mA 3.00 Output Voltage (V) Output Voltage (V) 2.90 2.80 2.70 2.60 2.90 2.80 2.70 Fig 197. Load Response Fige 198. Load Response 0 100 IOUT=100mA50mA 50 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 2.90 Output Voltage (V) 2.85 Output Voltage (V) 0 Output Current (mA) 100 Output Current (mA) 200 IOUT=0mA200mA 2.80 2.75 2.70 2.85 2.80 2.75 Fig 200. Load Response Fig 199. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Output Current (mA) 50 Output Current (mA) 100 IOUT=0mA100mA 27/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU28TD2WNVX (Ta=25C unless otherwise specified.) 1.0 2.0 0.0 4.0 2.0 0.0 Fig 201. Start Up Time Fig 202. Start Up Time Iout=0mA Iout=200mA 2.0 0.0 Output Voltage (V) 0.0 4.0 VIN=STBY=03.8V 4.0 2.0 0.0 4.0 2.0 0.0 Fig 203. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA Fig 204. Start Up Time (VIN=STBY) Iout=200mA 4.8 3.8 4.0 2.81 Output Voltage (V) Output Voltage (V) 0.0 5.8 VIN=3.84.8V3.8V Input Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=1.50V STBY Voltage (V) 2.0 STBY Voltage (V) 4.0 2.0 0.0 2.80 2.79 2.78 Fig 206. VIN Response Fig 205. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1.0 0.0 4.0 VIN=STBY=03.8V Output Voltage (V) STBY=01.5V Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY Voltage (V) STBY=01.5V STBY Voltage (V) 2.0 28/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU30TD2WNVX (Ta=25C unless otherwise specified.) 3.05 Temp=25C Output Voltage (V) 2.0 Io=0uA Io=100uA Io=50mA Io=200mA 1.5 1.0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 3.02 3.01 3.00 2.99 Io=0uA Io=100uA Io=50mA Io=200mA 2.98 2.97 2.95 2.9 0.0 5.5 20 Temp=-40C 3 3.1 3.2 3.3 3.4 3.5 3.6 0 Temp=85C 0.8 0.6 Temp=25C Temp=-40C 80 2 2.5 3 3.5 4 4.5 40 Temp=-40C Temp=25C 20 5 5.5 0 0.05 2.97 0.1 0.15 Temp=-40C 0 0.2 Temp=-40C 0.10 VIN = 0.98 x VOUT STBY=1.5V 0.05 0.05 0.1 0.15 2.5 VIN=3.5V 2.0 1.5 1.0 Temp=25C 2.0 1.5 Temp=25C 1.0 0.2 0.3 0.4 0.5 0.6 0 0.5 1.0 VIN=4.0V STBY=1.5V Io=0mA Gnd Current (uA) 50 3.01 3.00 2.99 2.98 2.97 1.5 Fig 215. STBY Threshold 60 3.02 1 STBY Voltage (V) Fig 214. OCP Threshold VIN=4.0V STBY=1.5V Io=0.1mA Temp=-40C Temp=85C Output Current (A) Fig 213. Dropout Voltage 3.03 2.5 0.0 0.1 Output Current (A) 3.04 0.2 0.5 STBY=1.5V 0 3.05 0.15 VIN=4.0V Io=0mA 3.0 VIN=4.0V VIN=5.5V 0.2 0.1 3.5 0.0 0 0.05 Fig 212. Load Regulation 0.5 0.00 Temp=85C Output Current (A) Output Voltage (V) Output Voltage (V) 0.15 5.5 2.98 3.0 Temp=25C 5 2.99 3.5 0.20 4.5 3.00 Fig 211. IOUT - IGND Temp=85C 4 Temp=25C 3.01 Output Current (A) Fig 210. VSTBY - ISTBY 0.25 3.5 2.95 Input Voltage (V) 0.30 3 3.02 2.96 1.5 2.5 3.03 0 1 2 VIN=4.0V STBY=1.5V 3.04 Temp=85C 60 0.0 0.5 1.5 3.05 VIN=4.0V STBY=1.5V 0.2 0 1 Fig 209. Circuit Current IGND Output Voltage (V) 1.2 0.4 0.5 Input Voltage (V) 100 1.4 Gnd Current (uA) STBY Pin Current (uA) Temp=25C 40 Fig 208. Line Regulation 1.6 Dropout Voltage (V) Temp=85C 60 Input Voltage (V) Fig 207. Output Voltage 1.0 VIN=STBY 80 0 Input Voltage (V) Output Voltage (V) Io=0uA 3.03 2.96 VIN=STBY 0.5 VIN=STBY VIN=4.0V STBY=0V 0.9 Gnd Current (uA) Output Voltage (V) 2.5 0 100 Temp=25C 3.04 3.0 Gnd Current (uA) 3.5 40 30 20 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 0.1 2.96 2.95 0.0 0 -40 -15 10 35 60 85 -40 Temp (C) Fig 216. VOUT - Temp -15 10 60 Temp (C) Fig 217. IGND - Temp www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 29/40 85 -40 -15 10 35 60 85 Temp (C) Fig 218. IGND - Temp (STBY) TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU30TD2WNVX (Ta=25C unless otherwise specified.) 0 100 50 IOUT=50mA0mA 0 3.10 Output Voltage (V) Output Voltage (V) 3.05 3.00 2.95 2.90 3.05 3.00 2.95 Fig 219. Load Response Fig 220. Load Response 0 100 50 IOUT=100mA0mA 0 3.10 Output Voltage (V) Output Voltage (V) 3.05 3.00 2.95 2.90 3.05 3.00 2.95 Fig 221. Load Response Fig 222. Load Response 0 200 100 IOUT=200mA0mA 0 3.20 Output Voltage (V) 3.10 Output Voltage (V) Output Current (mA) 100 Output Current (mA) 200 IOUT=0mA200mA 3.00 2.90 2.80 3.10 3.00 2.90 Fig 223. Load Response Fig 224. Load Response 0 100 IOUT=100mA50mA 50 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 3.10 Output Voltage (V) 3.05 Output Voltage (V) Output Current (mA) 50 Output Current (mA) 100 IOUT=0mA100mA 3.00 2.95 2.90 3.05 3.00 2.95 Fig 226. Load Response Fig 225. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Output Current (mA) 50 IOUT=0mA50mA Output Current (mA) 100 30/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU30TD2WNVX (Ta=25C unless otherwise specified.) 0.0 4.0 2.0 0.0 4.0 2.0 0.0 Fig 227. Start Up Time Fig 228. Start Up Time Iout=0mA Iout=200mA 4.0 2.0 0.0 4.0 2.0 0.0 Fig 229. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA Fig 230. Start Up Time (VIN=STBY) Iout=200mA STBY=1.50V 5.0 VIN=4.05.0V4.0V 4.0 4.0 3.01 Output Voltage (V) Output Voltage (V) 0.0 6.0 Input Voltage (V) 2.0 STBY Voltage (V) 4.0 2.0 0.0 3.00 2.99 2.98 Fig 232. VIN Response Fig 231. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 2.0 0.0 Output Voltage (V) 0.0 4.0 VIN=STBY=04.0V STBY Voltage (V) 2.0 STBY Voltage (V) 4.0 VIN=STBY=04.0V Output Voltage (V) 1.0 STBY=01.5V Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY Voltage (V) 1.0 STBY=01.5V STBY Voltage (V) 2.0 31/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series BU31TD2WNVX Reference data (Ta=25C unless otherwise specified.) 100 3.15 Temp=25C 3.14 Temp=25C Output Voltage (V) 2.5 2.0 Io=0uA Io=100uA Io=50mA Io=200mA 1.5 1.0 0.5 3.13 3.12 3.11 3.10 3.09 Io=0uA Io=100uA Io=50mA Io=200mA 3.08 3.07 3.06 VIN=STBY 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 3.1 3.2 Fig 233. Output Voltage Temp=-40C 3.3 3.4 3.5 3.6 0 3.7 Temp=85C 0.8 0.6 0.4 Temp=25C 1 1.5 2.5 3 3.5 4 4.5 5 5.5 3.15 VIN=4.1V STBY=1.5V 80 VIN=4.1V STBY=1.5V Temp=85C 60 40 Temp=-40C Temp=25C 20 Temp=-40C 2 Fig 235. Circuit Current IGND 3.13 Output Voltage (V) 1.2 1.0 0.5 Input Voltage (V) 100 1.4 Gnd Current (uA) Temp=25C 3.11 3.09 Temp=85C Temp=-40C 3.07 0.2 0.0 3.05 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0 5.5 0.05 Input Voltage (V) 0.15 0 0.2 3.0 Output Voltage (V) 3.5 0.25 Temp=85C 0.20 Temp=25C 0.15 Temp=-40C 0.10 VIN = 0.98 x VOUT STBY=1.5V 0.15 VIN=5.5V 2.0 1.5 1.0 Temp=25C 2.0 1.5 Temp=25C 1.0 Temp=-40C Temp=85C STBY=1.5V 0.0 0 0.2 0.1 0.2 0.3 0.4 0.5 0 0.6 0.5 Output Current (A) 1.0 VIN=4.1V STBY=1.5V Io=0mA Gnd Current (uA) 50 3.11 3.10 3.09 3.08 3.07 1.5 Fig 241. STBY Threshold 60 VIN=4.1V STBY=1.5V Io=0.1mA 1 STBY Voltage (V) Fig 240. OCP Threshold 3.15 3.12 2.5 0.5 Fig 239. Dropout Voltage 3.13 VIN=4.1V Io=0mA 3.0 VIN=4.1V 2.5 Output Current (A) 3.14 0.2 3.5 VIN=3.6V 0.0 0.1 0.15 Fig 238. Load Regulation 0.5 0.00 0.05 0.1 Output Current (A) Fig 237. IOUT - IGND 0.30 0 0.05 Output Current (A) Fig 236. VSTBY - ISTBY 0.05 0.1 Output Voltage (V) STBY Pin Current (uA) 20 Fig 234. Line Regulation 1.6 Dropout Voltage (V) Temp=25 40 Input Voltage (V) Input Voltage (V) Output Voltage (V) Temp=85 60 0 3 5.5 VIN=STBY 80 3.05 0.0 0 IO=0uA VIN=STBY VIN=4.1V STBY=0V 0.9 Gnd Current (uA) Output Voltage (V) 3.0 Gnd Current (uA) 3.5 40 30 20 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 3.06 0.1 0 3.05 -40 -15 10 35 60 85 0.0 -40 Temp (C) Fig 242. VOUT - Temp -15 10 60 Temp (C) Fig 243. IGND - Temp www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 32/40 85 -40 -15 10 35 60 85 Temp (C) Fig 244. IGND - Temp (STBY) TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU31TD2WNVX (Ta=25C unless otherwise specified.) 0 100 50 IOUT=50mA0mA 3.20 Output Voltage (V) Output Voltage (V) 3.15 3.10 3.05 3.00 3.15 3.10 3.05 Fig 245. Load Response Fig 246. Load Response 0 100 50 IOUT=100mA0mA 3.20 Output Voltage (V) Output Voltage (V) 3.15 3.10 3.05 3.00 3.15 3.10 3.05 Fig 247. Load Response Fig 248. Load Response 0 200 100 IOUT=200mA0mA 3.30 Output Voltage (V) 3.20 Output Voltage (V) 0 Output Current (mA) 100 Output Current (mA) 200 IOUT=0mA200mA 3.10 3.00 2.90 3.20 3.10 3.00 Fig 249. Load Response Fig 250. Load Response 0 100 IOUT=100mA50mA 50 0 3.15 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 3.20 Output Voltage (V) Output Voltage (V) 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=0mA100mA 3.10 3.05 3.00 3.15 3.10 3.05 Fig 252. Load Response Fig 251. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 Output Current (mA) 50 IOUT=0mA50mA Output Current (mA) 100 33/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU31TD2WNVX (Ta=25C unless otherwise specified.) 1.0 2.0 0.0 4.0 2.0 0.0 Fig 253. Start Up Time Fig 254. Start Up Time Iout=0mA Iout=200mA 2.0 0.0 Output Voltage (V) 0.0 4.0 VIN=STBY=04.1V 4.0 2.0 0.0 4.0 2.0 0.0 Fig 255. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA Fig 256. Start Up Time (VIN=STBY) Iout=200mA 5.1 4.1 4.0 3.11 Output Voltage (V) Output Voltage (V) 0.0 6.1 VIN=4.1V5.1V4.1V Input Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=1.50V STBY Voltage (V) 2.0 STBY Voltage (V) 4.0 2.0 0.0 3.10 3.09 3.08 Fig 258. VIN Response Fig 257. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1.0 0.0 4.0 VIN=STBY=04.1V Output Voltage (V) STBY=01.5V Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY Voltage (V) STBY=01.5V STBY Voltage (V) 2.0 34/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series BU33TD2WNVX Reference data (Ta=25C unless otherwise specified.) 3.5 3.35 Output Voltage (V) 2.5 2.0 Io=0uA Io=100uA Io=50mA Io=200mA 1.5 1.0 0.5 VIN=STBY VIN=STBY 3.32 3.31 3.30 3.29 3.28 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 20 5.5 3.2 3.3 3.4 3.6 3.7 3.8 3.9 0 Temp=85C 0.8 0.6 80 60 40 Temp=-40C Temp=25C 20 Temp=-40C 3.32 1.5 2 2.5 3 3.5 4 4.5 5 0.05 Input Voltage (V) Fig 262. VSTBY - ISTBY 0.1 0.15 3.27 0.15 Temp=-40C 0.10 VIN = 0.98 x VOUT STBY=1.5V 0.05 0.05 0.1 0.15 1.50 1.00 Temp=25C 0.50 STBY=1.5V 2.0 1.5 Temp=25C 1.0 0.2 0.3 0.4 0.5 0.6 0 0.5 1.0 VIN=4.3V STBY=1.5V Io=0mA Gnd Current (uA) 50 3.30 3.29 3.28 3.27 1.5 Fig 267. STBY Threshold 60 3.31 1 STBY Voltage (V) Fig 266. OCP Threshold 3.32 Temp=-40C Temp=85C 0.5 0.0 0.1 Fig 265. Dropout Voltage 3.33 2.5 Output Current (A) VIN=4.3V STBY=1.5V Io=0.1mA 0.2 VIN=4.3V Io=0mA 3.0 2.00 Output Current (A) 3.34 0.15 Fig 264. Load Regulation VIN=4.3V 2.50 0 3.35 0.1 3.5 VIN=5.5V 0.2 Temp=85C 0.05 Output Current (A) 0.00 0.00 0 Temp=-40C 0 0.2 Output Voltage (V) Output Voltage (V) Temp=25C 5.5 3.28 VIN=3.8V 3.00 0.20 5 3.29 Fig 263. IOUT - IGND Temp=85C 4.5 3.30 3.50 0.25 4 Temp=25C Output Current (A) 0.30 3.5 3.25 0 5.5 3 3.31 0 1 2.5 3.33 3.26 0.0 2 VIN=4.3V STBY=1.5V 3.34 Temp=85C 0.2 0.5 1.5 3.35 VIN=4.3V STBY=1.5V Output Voltage (V) 1.2 0 1 Fig 261. Circuit Current IGND 100 1.4 Temp=25C 0.5 Input Voltage (V) Fig 260. Line Regulation Gnd Current (uA) STBY Pin Current (uA) 3.5 Input Voltage (V) 1.6 0.4 Temp=-40C 0 Fig 259. Output Voltage Dropout Voltage (V) Temp=25C 40 3.27 Input Voltage (V) 1.0 Temp=85C 60 3.25 0 VIN=STBY 80 3.26 0.0 Output Voltage (V) Io=0uA Io=0uA Io=100uA Io=50mA Io=200mA 3.33 0.9 Gnd Current (uA) Output Voltage (V) 100 Temp=25C 3.34 Gnd Current (uA) Temp=25C 3.0 40 30 20 VIN=4.3V STBY=0V 0.8 0.7 0.6 0.5 0.4 0.3 0.2 10 3.26 0.1 3.25 0 -40 -15 10 35 60 85 0.0 -40 Temp (C) Fig 268. VOUT - Temp -15 10 60 Temp (C) Fig 269. IGND - Temp www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35 35/40 85 -40 -15 10 35 60 85 Temp (C) Fig 270. IGND - Temp (STBY) TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU33TD2WNVX (Ta=25C unless otherwise specified.) 0 100 50 IOUT=50mA0mA 0 3.40 Output Voltage (V) Output Voltage (V) 3.35 3.30 3.25 3.20 3.35 3.30 3.25 Fig 271. Load Response Fig 272. Load Response 0 100 50 IOUT=100mA0mA 0 3.40 Output Voltage (V) Output Voltage (V) 3.35 3.30 3.25 3.20 3.35 3.30 3.25 Fig 273. Load Response Fig 274. Load Response 0 200 100 IOUT=200mA0mA 0 3.50 Output Voltage (V) Output Voltage (V) 3.40 Output Current (mA) 100 IOUT=0mA200mA Output Current (mA) 200 3.30 3.20 3.10 3.40 3.30 3.20 Fig 275. Load Response Fig 276. Load Response 0 100 IOUT=100mA50mA 50 0 Output Current (mA) 50 Output Current (mA) 100 IOUT=50mA100mA 3.40 Output Voltage (V) 3.35 Output Voltage (V) Output Current (mA) 50 IOUT=0mA100mA Output Current (mA) 100 3.30 3.25 3.20 3.35 3.30 3.25 Fig 278. Load Response Fig 277. Load Response www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Output Current (mA) 50 IOUT=0mA50mA Output Current (mA) 100 36/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Reference data BU33TD2WNVX (Ta=25C unless otherwise specified.) 1.0 2.0 0.0 4.0 2.0 0.0 Fig 279. Start Up Time Fig 280. Start Up Time Iout=0mA Iout=200mA 4.0 2.0 0.0 4.0 2.0 0.0 Fig 281. Start Up Time (VIN=STBY) Iout=0mA Iout=0mA Fig 282. Start Up Time (VIN=STBY) Iout=200mA 5.3 4.3 4.0 3.31 Output Voltage (V) Output Voltage (V) 0.0 6.3 VIN=4.3V5.3V5.3V Input Voltage (V) 1.0 STBY Voltage (V) 2.0 STBY=1.50V 2.0 0.0 Output Voltage (V) 0.0 4.0 VIN=STBY=04.3V STBY Voltage (V) 2.0 STBY Voltage (V) 4.0 2.0 0.0 3.30 3.29 3.28 Fig 284. VIN Response Fig 283. Discharge Time www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1.0 0.0 4.0 VIN=STBY=04.3 V Output Voltage (V) STBY=01.5V Output Voltage (V) Output Voltage (V) 0.0 2.0 STBY Voltage (V) STBY=01.5V STBY Voltage (V) 2.0 37/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series z About power dissipation (Pd) As for power dissipation, an approximate estimate of the heat reduction characteristics and internal power consumption of IC are shown, so please use these for reference. Since power dissipation changes substantially depending on the implementation conditions (board size, board thickness, metal wiring rate, number of layers and through holes, etc.), it is recommended to measure Pd on a set board. Exceeding the power dissipation of IC may lead to deterioration of the original IC performance, such as causing operation of the thermal shutdown circuit or reduction in current capability. Therefore, be sure to prepare sufficient margin within power dissipation for usage. Calculation of the maximum internal power consumption of IC (PMAX) PMAX=(VIN-VOUT)xIOUT(MAX.) (VIN: Input voltage VOUT: Output voltage IOUT(MAX): Maximum output current) { Measurement conditions Standard ROHM Board Evaluation Board 1 Top Layer (Top View) Top Layer (Top View) Layout of Board for Measurement IC Implementation Position Bottom Layer (Top View) Bottom Layer (Top View) Measurement State With board implemented (Wind speed 0 m/s) With board implemented (Wind speed 0 m/s) Board Material Glass epoxy resin (Double-side board) Glass epoxy resin (Double-side board) Board Size 70 mm x 70 mm x 1.6 mm 40 mm x 40 mm x 1.6 mm Top layer Wiring Bottom Rate layer Through Hole Metal (GND) wiring rate: Approx. 0% Metal (GND) wiring rate: Approx. 50% Metal (GND) wiring rate: Approx. 50% Metal (GND) wiring rate: Approx. 50% Diameter 0.5mm x 6 holes Diameter 0.5mm x 25 holes Power Dissipation Thermal Resistance 0.56W 0.39W ja=178.6C/W ja=256.4C/W 0.6 0.56W 0.5 Pd [W] 0.4 0.39W 0.3 * Please design the margin so that PMAX becomes is than Pd (PMAX<Pd) within the usage temperature range 0.2 0.1 0 0 25 50 75 85 100 125 Ta [] Fig. 285 SSON004X1010 Power dissipation heat reduction characteristics (Reference) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 38/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Operation Notes 1.) Absolute maximum ratings Use of the IC in excess of absolute maximum ratings (such as the input voltage or operating temperature range) may result in damage to the IC. Assumptions should not be made regarding the state of the IC (e.g., short mode or open mode) when such damage is suffered. If operational values are expected to exceed the maximum ratings for the device, consider adding protective circuitry (such as fuses) to eliminate the risk of damaging the IC. 2.) GND potential The potential of the GND pin must be the minimum potential in the system in all operating conditions. Never connect a potential lower than GND to any pin, even if only transiently. 3.) Thermal design Use a thermal design that allows for a sufficient margin for that package power dissipation rating (Pd) under actual operating conditions. 4.) Inter-pin shorts and mounting errors Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting or shorts between pins may result in damage to the IC. 5.) Operation in strong electromagnetic fields Strong electromagnetic fields may cause the IC to malfunction. Caution should be exercised in applications where strong electromagnetic fields may be present. 6.) Common impedance Wiring traces should be as short and wide as possible to minimize common impedance. Bypass capacitors should be use to keep ripple to a minimum. 7.) Voltage of STBY pin To enable standby mode for all channels, set the STBY pin to 0.3 V or less, and for normal operation, to 1.2 V or more. STBY to a voltage between 0.3 and 1.2 V may cause malfunction and should be avoided. Setting Keep transition time between high and low (or vice versa) to a minimum. Additionally, if STBY is shorted to VIN, the IC will switch to standby mode and disable the output discharge circuit, causing a temporary voltage to remain on the output pin. occur on the output. If the IC is switched on again while this voltage is present, overshoot may Therefore, in applications where these pins are shorted, the output should always be completely discharged before turning the IC on. 8.) Over-current protection circuit (OCP) This IC features an integrated over-current and short-protection circuitry on the output to prevent destruction of the IC when the output is shorted. The OCP circuitry is designed only to protect the IC from irregular conditions (such as motor output shorts) and is not designed to be used as an active security device for the application. Therefore, applications should not be designed under the assumption that this circuitry will engage. 9.) Thermal shutdown circuit (TSD) This IC also features a thermal shutdown circuit that is designed to turn the output off when the junction temperature of the IC exceeds about 150. This feature is intended to protect the IC only in the event of thermal overload and is not designed to guarantee operation or act as an active security device for the application. Therefore, applications should not be designed under the assumption that this circuitry will engage. 10.) Input/output capacitor Capacitors must be connected between the input/output pins and GND for stable operation, and should be physically mounted as close to the IC pins as possible. The input capacitor helps to counteract increases in power supply impedance, and increases stability in applications with long or winding power supply traces. The output capacitance value is directly related to the Unstablevalue region overall stability and transient response of the regulator, and should be set to the largest possible for the application to increase these characteristics. During design, keep in mind that in general, ceramic capacitors have a wide range of tolerances, temperature coefficients and DC bias characteristics, and that their capacitance values tend to decrease over time. Confirm these details before choosing appropriate capacitors for your application.(Please refer the technical note, regarding ceramic capacitor of recommendation) Cout=0.47F, Cin=0.47F, Temp=+25 11.) About the equivalent series resistance (ESR) of a ceramic capacitor 100 Capacitors generally have ESR (equivalent series resistance) and it operates stably in the ESR-IOUT area shown on the right. 10 capacitors, etc. generally have different ESR, please check the ESR of the capacitor to be used and use it within the stability area range shown in the right graph for evaluation of the actual application. ESR[] [] ESR Since ceramic capacitors, tantalum capacitors, electrolytic 1 0.1 0.01 0 50 100 150 200 IOUT [mA] Fig. 286 www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 39/40 Stable region (example) TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet BUxxTD2WNVX series Revision History Date Revision 7.Feb.2013 001 15.Mar.2013 002 24.Apr.2013 003 31.Jul.2013 004 21.Aug.2013 28.Aug.2013 005 006 24.Oct.2013 007 14.Jan.2014 008 Changes New Release. Adding Reference data. Adding a Revision History. Adding 1.3V product. Adding dropout voltage. Delete ELECTRICAL CHARACTERISTICS of each Output Voltage. VSBYH is changed. Adding dropout voltage. Ordering Information is changed. Adding Pin Descriptions. Adding BOTTOM VIEW. Adding 1.1V product www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 40/40 TSZ02201-0RBR0A300050-1-2 14.Jan.2013.Rev.008 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice - WE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet bu1atd2wnvx - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS bu1atd2wnvx SSON004X1010 5000 5000 Taping inquiry Yes