6N138S1-V - Everlight International Corp.

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 1 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

Features:

• High current transfer ratio–2000% typical

• High isolation voltage between input

and output (Viso=5000 Vrms )

• Guaranteed performance from 0°C to 70°C

• Pb free and RoHS compliant.

• UL approved (No. 214129)

• VDE approved (No. 132249)

• SEMKO approved

• NEMKO approved

• DEMKO approved

• FIMKO approved

• CSA approved (No. 2037145)

Description

The 6N138 and 6N139 devices each consists of an infrared

emitting diode, optically coupled to a high gain split Darlington

photo detector. They provide extremely high current transfer

ratio between input and output, with access to a base terminal

to adjust the gain bandwidth.

Schematic

These devices are packaged in an 8-pin DIP package

and available in wide-lead spacing and SMD options.

1 8

Applications 2

• Digital logic ground isolation

• RS-232C line receiver

• Low input current line receiver

• Microprocessor bus isolation

• Current loop receiver

Pin Configuration

1. No Connection

2. Anode

3. Cathode

4. No Connection

5. Gnd

6. Vout

7. VB

8. Vcc

5

6

7

3

4

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 2 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

Absolute Maximum Ratings (Ta=25°C unless otherwise specified)

Parameter Symbol Rating Unit

Forward current IF 20 mA

Peak forward current

(50% duty, 1ms P.W) IFP 40 mA

Peak transient current

(≤1μs P.W, 300pps) IFtrans 1 A

Reverse voltage VR 5 V

Input

Power dissipation PIN 45 mW

Power dissipation PO 100 mW

Output current IO 60 mA

Emitter-Base Reverse Voltage VER 0.5 V

6N138 -0.5 to 7 V

Output voltage

6N139

VO

-0.5 to 18 V

6N138 -0.5 to 7 V

Output

Supply voltage

6N139

VCC

-0.5 to 18 V

Isolation voltage *1 V

ISO 5000 V rms

Operating temperature TOPR -40 ~ +85 °C

Storage temperature TSTG -55 ~ +125 °C

Soldering temperature *2 T

SOL 260 °C

Notes

*1 AC for 1 minute, R.H.= 40 ~ 60% R.H. In this test, pins 1, 2, 3, 4 are shorted together, and pins 5, 6, 7, 8

are shorted together.

*2 For 10 seconds.

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 3 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

Electrical Characteristics (Ta=0 to 70°C unless specified otherwise)

Input

Parameter Symbol Min. Typ.* Max. Unit Condition

Forward voltage VF - 1.3 1.7 V

IF = 1.6mA

Reverse Voltage VR 5.0 - - V

IR = 10μA, TA=25°C

Temperature coefficient of

forward voltage ΔVF/ΔTA - -1.8 - mV/°C IF =1.6mA

Output

Parameter Symbol Min. Typ.* Max. Unit Condition

6N139 - 0.01 100

Logic High

Output Current 6N138

IOH

- - 250

µA

IF=0mA, VO=VCC=18V

Logic Low

Supply Current

6N138

6N139 ICCL - 0.6 1.5

mA IF=1.6mA, VO=Open,

VCC=18V

Logic High

Supply Current

6N138

6N139 ICCH - 0.05 10 µA IF=0mA, VO=Open,

VCC=18V

Transfer Characteristics (Ta=0 to 70°C unless specified otherwise, Vcc=4.5V)

Parameter Symbol Min. Typ.* Max. Unit Condition

400 2500 - IF = 0.5mA, VO = 0.4V,

VCC=4.5V

6N139

500 2000 -

Current Transfer

Ratio

6N138

CTR

300 2000 -

%

IF = 1.6mA, VO = 0.4V,

VCC=4.5V

- 0.05 0.4 IF = 0.5mA, IO = 2mA,

VCC=4.5V

- 0.09 0.4 IF = 1.6mA, IO = 8mA,

VCC=4.5V

- 0.12 0.4 IF = 5mA, IO = 15mA,

VCC=4.5V

6N139

- 0.17 0.4 IF = 12mA, IO = 24mA,

VCC=4.5V

Logic Low

Output Voltage

6N138

VOL

- 0.06 0.4

V

IF = 1.6mA, IO = 4.8mA,

VCC=4.5V

* Typical values at Ta = 25°C

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 4 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

Switching Characteristics (Ta=0 to 70°C unless specified otherwise, Vcc=5V)

Parameter Symbol Min. Typ.* Max. Unit Condition

- 5 25 IF = 0.5mA , RL=4.7kΩ,

TA=25°C

- - 30 IF = 0.5mA , RL=4.7kΩ

- 0.2 1 IF = 12mA , RL=270Ω,

TA=25°C

6N139

- - 2 IF = 12mA , RL=270Ω

- 1.4 10 IF = 1.6mA , RL=2.2kΩ,

TA=25°C

Propagation

Delay Time to

Logic Low

(Fig. 13)

6N138

TPHL

- - 15

µs

IF = 1.6mA , RL=2.2kΩ

- 16 60 IF = 0.5mA , RL=4.7kΩ,

TA=25°C

- - 90 IF = 0.5mA , RL=4.7kΩ

- 1.7 7 IF = 12mA , RL=270Ω,

TA=25°C

6N139

- - 10 IF = 12mA , RL=270Ω

- 8 35 IF = 1.6mA , RL=2.2kΩ,

TA=25°C

Propagation

Delay Time to

Logic High

(Fig. 13)

6N138

TPLH

- -

50

µs

IF = 1.6mA , RL=2.2kΩ

Common Mode Transient

Immunity at Logic High

(Fig. 14) *3 CMH 1,000 - - V/µs IF = 0mA , VCM=10Vp-p,

RL=2.2KΩ, TA=25°C

Common Mode Transient

Immunity at Logic Low

(Fig. 14) *3 CML 1,000 - - V/µs IF = 1.6mA , VCM=10Vp-p,

RL=2.2KΩ, TA=25°C

* Typical values at Ta = 25°C

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 5 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

Typical Performance Curves

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 6 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

Everlight Electronics Co., Ltd. 7 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER 6N138 6N139

Fig. 13 Switching Time Test Circuit and Waveform

Fig. 14 Common Mode Transient Immunity Test Circuit and Waveform

Note:

*3 Common mode transient immunity in logic high level is the maximum tolerable (positive) dVcm/dt on the

leading edge of the common mode pulse signal VCM, to assure that the output will remain in a logic high

state (i.e., VO > 2.0V).

Common mode transient immunity in logic low level is the maximum tolerable (negative) dVcm/dt on the

trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a logic low

state (i.e., VO < 0.8V).

IF

VO

5V

1.5V

VOL

tPLH tPHL

+

5V

V

o

RL

0.1uF 0.1uF

Rin

IF

Monitor

IF

Pulse

Generator

Tr=5ns,

Zo=50Ω

VF

CMH: Switch at B (IF=0mA)

CML: Switch at A (IF=1.6mA)

IF +

5V

RL

0.1uF

VF

Vo

B

A

VFF

VCM

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 8 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

Order Information

Part Number

6N13XY(Z)-V

Note

X = Part No. (X = 8 or 9)

Y = Lead form option (S, S1, M or none)

Z = Tape and reel option (TA, TB or none).

V = VDE (optional)

Option Description Packing quantity

None Standard DIP-8 45 units per tube

M Wide lead bend (0.4 inch spacing) 45 units per tube

S (TA) Surface mount lead form + TA tape & reel option 1000 units per reel

S (TB) Surface mount lead form + TB tape & reel option 1000 units per reel

S1 (TA) Surface mount lead form (low profile) + TA tape & reel option 1000 units per reel

S1 (TB) Surface mount lead form (low profile) + TB tape & reel option 1000 units per reel

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

Everlight Electronics Co., Ltd. 9 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

SPLIT DARLINGTON PHOTOCOUPLER

6N138 6N139

Package Drawing

(Dimensions in mm)

Standard DIP Type

Option M Type

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 10 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

Option S Type

Option S1 Type

Everlight Electronics Co., Ltd. 11 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

6N138 6N139

Recommended pad layout for surface mount leadform

Device Marking

EL

6N138

YWWV

Notes

6N138 denotes Device Number

Y denotes 1 digit Year code

WW denotes 2 digit Week code

V denotes VDE (Optional)

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 12 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

Tape & Reel Packing Specifications

ape dimensions

Dimension No. A B Do D1 E F

Option TA Option TB

Direction of feed from reel Direction of feed from reel

T

Dimension(mm) 10.4±0.1 10.0±0.1 1.5±0.1 1.5±0.1 1.75±0.1 7.5±0.1

Dimension No. Po P1 P2 t W K

12.0±0.1 2.0±0.1 0.4±0.1 16.0+0.3/

-0.1 4.5±0.1 Dimension(mm) 4.0±0.1

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 13 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

TIME

(

S

)

150°C

1-3 °C/Sec Max

70

–

170 Sec

200°

217°

260 °C (p

em P

eak,10 Sec Max)

Solder Reflow T perature rofile

>255 °C

(

30s Max

)

1-3 °C/Sec Max 60

–

140 Sec

8 PIN DIP LOW INPUT CURRENT HIGH GAIN

SPLIT DARLINGTON PHOTOCOUPLER

Everlight Electronics Co., Ltd. 14 http://www.everlight.com

Document No：DPC-0000019 Rev.2 February 23, 2009

6N138 6N139

DISCLAIMER

. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change

for above specification.

. When using this product, please observe the absolute maximum ratings and the instructions for using

outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting

from use of the product which does not comply with the absolute maximum ratings and the instructions

included in these specification sheets.

ation sheets include materials protected under copyright of EVERLIGHT corporation. Please

1

2

3. These specific

don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.